In some rare cases the 32 bit Rt value will overflow if z2 and x is max,
z1 is minimal value and x_plate_ohms is relatively high (for example 800
ohm). This would happen on some screen age with low pressure.
There are two possible fixes:
- make Rt 64bit
- reorder calculation to avoid overflow
The second variant seems to be preferable, since 64 bit calculation on
32 bit system is a bit more expensive.
Fixes: ffa458c1bd ("spi: ads7846 driver")
Co-developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201113112240.1360-1-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Starting with 3eac5c7e44 ("Input: ads7846 - extend the driver for ads7845
controller support"), the ads7845 was partially converted to full duplex
mode.
Since it is not touchscreen controller specific, it is better to extend
this conversion to cover entire driver. This will reduce CPU load and make
driver more readable.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201110085041.16303-2-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If touchscreen is released while busy reading HWMON device, the release
can be missed. The IRQ thread is not started because no touch is active
and BTN_TOUCH release event is never sent.
Fixes: f5a28a7d48 ("Input: ads7846 - avoid pen up/down when reading hwmon")
Co-developed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201027105416.18773-1-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"A fix for use-after-free in the Sun keyboard driver, a fix to firmware
updates on newer ICs in the Elan touchpad diver, and a couple misc
driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - fix firmware update on newer ICs
Input: resistive-adc-touch - fix kconfig dependency on IIO_BUFFER
Input: sunkbd - avoid use-after-free in teardown paths
Input: i8042 - allow insmod to succeed on devices without an i8042 controller
Input: adxl34x - clean up a data type in adxl34x_probe()
Fixes the following W=1 kernel build warning(s):
drivers/input/touchscreen/imx6ul_tsc.c: In function ‘adc_irq_fn’:
drivers/input/touchscreen/imx6ul_tsc.c:307:6: warning: variable ‘value’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20201112110204.2083435-6-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/keyboard/samsung-keypad.c: In function ‘samsung_keypad_irq’:
drivers/input/keyboard/samsung-keypad.c:149:15: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201112110204.2083435-3-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Do not overwrite spi->mode flags set by spi framework, otherwise the
chip select polarity will get lost.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20201027095724.18654-3-o.rempel@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Hard-coding resolution for st1633 device was wrong. Some of LCDs like
YTS700TLBC-02-100C has assembled Sitronix st1633 touchcontroller too. But
the resolution is not 320x480 as was hard-coded.
Add new function which reads correct resolution directly from register.
Signed-off-by: Andrej Valek <andrej.valek@siemens.com>
Link: https://lore.kernel.org/r/20201103073949.12198-1-andrej.valek@siemens.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When TOUCHSCREEN_ADC is enabled and IIO_BUFFER is disabled, it results
in the following Kbuild warning:
WARNING: unmet direct dependencies detected for IIO_BUFFER_CB
Depends on [n]: IIO [=y] && IIO_BUFFER [=n]
Selected by [y]:
- TOUCHSCREEN_ADC [=y] && !UML && INPUT [=y] && INPUT_TOUCHSCREEN [=y] && IIO [=y]
The reason is that TOUCHSCREEN_ADC selects IIO_BUFFER_CB without depending
on or selecting IIO_BUFFER while IIO_BUFFER_CB depends on IIO_BUFFER. This
can also fail building the kernel.
Honor the kconfig dependency to remove unmet direct dependency warnings
and avoid any potential build failures.
Fixes: aa132ffb6b ("input: touchscreen: resistive-adc-touch: add generic resistive ADC touchscreen")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20201102221504.541279-1-fazilyildiran@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the kerneldoc warnings from building the driver with W=1.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104162427.2984742-2-lee.jones@linaro.org
[dtor: folded together several Lee's patches; added more descriptions]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
In file included from drivers/input/touchscreen/cyttsp_i2c_common.c:24:
drivers/input/touchscreen/cyttsp4_core.h:236:27: warning: ‘cyttsp4_tch_abs_string’ defined but not used [-Wunused-const-variable=]
236 | static const char const cyttsp4_tch_abs_string[] = {
| ^~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/input/touchscreen/cyttsp4_i2c.c:17:
drivers/input/touchscreen/cyttsp4_core.h:236:27: warning: ‘cyttsp4_tch_abs_string’ defined but not used [-Wunused-const-variable=]
236 | static const char * const cyttsp4_tch_abs_string[] = {
| ^~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/input/touchscreen/cyttsp4_spi.c:17:
drivers/input/touchscreen/cyttsp4_core.h:236:27: warning: ‘cyttsp4_tch_abs_string’ defined but not used [-Wunused-const-variable=]
236 | static const char * const cyttsp4_tch_abs_string[] = {
| ^~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104162427.2984742-16-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/mouse/cyapa_gen5.c:392: warning: Function parameter or member 'cyapa' not described in 'cyapa_i2c_pip_write'
drivers/input/mouse/cyapa_gen5.c:392: warning: Function parameter or member 'buf' not described in 'cyapa_i2c_pip_write'
drivers/input/mouse/cyapa_gen5.c:392: warning: Function parameter or member 'size' not described in 'cyapa_i2c_pip_write'
drivers/input/mouse/cyapa_gen5.c:444: warning: Function parameter or member 'cyapa' not described in 'cyapa_empty_pip_output_data'
drivers/input/mouse/cyapa_gen5.c:444: warning: Function parameter or member 'buf' not described in 'cyapa_empty_pip_output_data'
drivers/input/mouse/cyapa_gen5.c:444: warning: Function parameter or member 'len' not described in 'cyapa_empty_pip_output_data'
drivers/input/mouse/cyapa_gen5.c:444: warning: Function parameter or member 'func' not described in 'cyapa_empty_pip_output_data'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104162427.2984742-4-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/mouse/cyapa.c:130: warning: Function parameter or member 'reg' not described in 'cyapa_i2c_write'
drivers/input/mouse/cyapa.c:130: warning: Excess function parameter 'ret' description in 'cyapa_i2c_write'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20201104162427.2984742-3-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/misc/ab8500-ponkey.c:32: warning: Function parameter or member 'idev' not described in 'ab8500_ponkey'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104162427.2984742-5-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/keyboard/cros_ec_keyb.c:72: warning: cannot understand function prototype: 'struct cros_ec_bs_map '
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Link: https://lore.kernel.org/r/20201104162427.2984742-8-lee.jones@linaro.org
[dtor: fixed up docbook comments for cros_ec_keyb structure as well]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/keyboard/gpio_keys.c:119: warning: Function parameter or member 'dev' not described in 'get_bm_events_by_type'
drivers/input/keyboard/gpio_keys.c:119: warning: Excess function parameter 'input' description in 'get_bm_events_by_type'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104162427.2984742-12-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/mouse/elantech.c:1837: warning: Function parameter or member 'psmouse' not described in 'elantech_setup_smbus'
drivers/input/mouse/elantech.c:1837: warning: Function parameter or member 'info' not described in 'elantech_setup_smbus'
drivers/input/mouse/elantech.c:1837: warning: Function parameter or member 'leave_breadcrumbs' not described in 'elantech_setup_smbus'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104162427.2984742-13-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'num_rows' not described in 'pmic8xxx_kp'
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'num_cols' not described in 'pmic8xxx_kp'
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'input' not described in 'pmic8xxx_kp'
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'regmap' not described in 'pmic8xxx_kp'
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'key_sense_irq' not described in 'pmic8xxx_kp'
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'key_stuck_irq' not described in 'pmic8xxx_kp'
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'keycodes' not described in 'pmic8xxx_kp'
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'dev' not described in 'pmic8xxx_kp'
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'keystate' not described in 'pmic8xxx_kp'
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'stuckstate' not described in 'pmic8xxx_kp'
drivers/input/keyboard/pmic8xxx-keypad.c:106: warning: Function parameter or member 'ctrl_reg' not described in 'pmic8xxx_kp'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104162427.2984742-21-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/keyboard/nomadik-ske-keypad.c:71: warning: Function parameter or member 'pclk' not described in 'ske_keypad'
drivers/input/keyboard/nomadik-ske-keypad.c:71: warning: Function parameter or member 'ske_keypad_lock' not described in 'ske_keypad'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104162427.2984742-20-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/misc/drv2667.c:109: warning: Function parameter or member 'input_dev' not described in 'drv2667_data'
drivers/input/misc/drv2667.c:109: warning: Function parameter or member 'client' not described in 'drv2667_data'
drivers/input/misc/drv2667.c:109: warning: Function parameter or member 'regmap' not described in 'drv2667_data'
drivers/input/misc/drv2667.c:109: warning: Function parameter or member 'work' not described in 'drv2667_data'
drivers/input/misc/drv2667.c:109: warning: Function parameter or member 'regulator' not described in 'drv2667_data'
drivers/input/misc/drv2667.c:109: warning: Function parameter or member 'page' not described in 'drv2667_data'
drivers/input/misc/drv2667.c:109: warning: Function parameter or member 'magnitude' not described in 'drv2667_data'
drivers/input/misc/drv2667.c:109: warning: Function parameter or member 'frequency' not described in 'drv2667_data'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104162427.2984742-19-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/misc/drv2665.c:59: warning: Function parameter or member 'input_dev' not described in 'drv2665_data'
drivers/input/misc/drv2665.c:59: warning: Function parameter or member 'client' not described in 'drv2665_data'
drivers/input/misc/drv2665.c:59: warning: Function parameter or member 'regmap' not described in 'drv2665_data'
drivers/input/misc/drv2665.c:59: warning: Function parameter or member 'work' not described in 'drv2665_data'
drivers/input/misc/drv2665.c:59: warning: Function parameter or member 'regulator' not described in 'drv2665_data'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104162427.2984742-18-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'input_dev' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'client' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'regmap' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'work' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'enable_gpio' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'regulator' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'magnitude' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'mode' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'library' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'rated_voltage' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:194: warning: Function parameter or member 'overdrive_voltage' not described in 'drv260x_data'
drivers/input/misc/drv260x.c:244: warning: Function parameter or member 'voltage' not described in 'drv260x_calculate_voltage'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104162427.2984742-17-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We need to make sure we cancel the reinit work before we tear down the
driver structures.
Reported-by: Bodong Zhao <nopitydays@gmail.com>
Tested-by: Bodong Zhao <nopitydays@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The eKTF2132 is a touchscreen controller found, for example, in the Kobo
Aura ebook reader. It is similar to the ektf2127, but it uses a different
packet type to report touch events.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Link: https://lore.kernel.org/r/20201106112412.390724-3-j.neuschaefer@gmx.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The i8042 module exports several symbols which may be used by other
modules.
Before this commit it would refuse to load (when built as a module itself)
on systems without an i8042 controller.
This is a problem specifically for the asus-nb-wmi module. Many Asus
laptops support the Asus WMI interface. Some of them have an i8042
controller and need to use i8042_install_filter() to filter some kbd
events. Other models do not have an i8042 controller (e.g. they use an
USB attached kbd).
Before this commit the asus-nb-wmi driver could not be loaded on Asus
models without an i8042 controller, when the i8042 code was built as
a module (as Arch Linux does) because the module_init function of the
i8042 module would fail with -ENODEV and thus the i8042_install_filter
symbol could not be loaded.
This commit fixes this by exiting from module_init with a return code
of 0 if no controller is found. It also adds a i8042_present bool to
make the module_exit function a no-op in this case and also adds a
check for i8042_present to the exported i8042_command function.
The latter i8042_present check should not really be necessary because
when builtin that function can already be used on systems without
an i8042 controller, but better safe then sorry.
Reported-and-tested-by: Marius Iacob <themariusus@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201008112628.3979-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The "revid" is used to store negative error codes so it should be an int
type.
Fixes: e27c729219 ("Input: add driver for ADXL345/346 Digital Accelerometers")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Link: https://lore.kernel.org/r/20201026072824.GA1620546@mwanda
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull more parisc updates from Helge Deller:
- During this merge window O_NONBLOCK was changed to become 000200000,
but we missed that the syscalls timerfd_create(), signalfd4(),
eventfd2(), pipe2(), inotify_init1() and userfaultfd() do a strict
bit-wise check of the flags parameter.
To provide backward compatibility with existing userspace we
introduce parisc specific wrappers for those syscalls which filter
out the old O_NONBLOCK value and replaces it with the new one.
- Prevent HIL bus driver to get stuck when keyboard or mouse isn't
attached
- Improve error return codes when setting rtc time
- Minor documentation fix in pata_ns87415.c
* 'parisc-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
ata: pata_ns87415.c: Document support on parisc with superio chip
parisc: Add wrapper syscalls to fix O_NONBLOCK flag usage
hil/parisc: Disable HIL driver when it gets stuck
parisc: Improve error return codes when setting rtc time
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----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=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
cros-ec:
* Error code cleanup across cros-ec by Guenter.
* Remove cros_ec_cmd_xfer in favor of cros_ec_cmd_xfer_status.
cros_ec_typec:
* Landed initial USB4 support in typec connector class driver for cros_ec.
* Role switch bugfix on disconnect, and reordering configuration steps.
cros_ec_lightbar:
* Fix buffer outsize and result for get_lightbar_version.
misc:
* Remove config MFD_CROS_EC, now that transition from MFD is complete.
* Enable KEY_LEFTMETA in new location on arm based cros-ec-keyboard keymap.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQQCtZK6p/AktxXfkOlzbaomhzOwwgUCX5G2IAAKCRBzbaomhzOw
wo4JAQC7BcJJwYgoVnRQvYd4xXCEsl/F9cVFJJLRYAH/PA4x6gEA+wfdIxebAXbO
RapU2HOppxiQGFkr+0FX5xV+O7cRNAo=
=gkul
-----END PGP SIGNATURE-----
Merge tag 'tag-chrome-platform-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"cros-ec:
- Error code cleanup across cros-ec by Guenter
- Remove cros_ec_cmd_xfer in favor of cros_ec_cmd_xfer_status
cros_ec_typec:
- Landed initial USB4 support in typec connector class driver for
cros_ec
- Role switch bugfix on disconnect, and reordering configuration
steps
cros_ec_lightbar:
- Fix buffer outsize and result for get_lightbar_version
misc:
- Remove config MFD_CROS_EC, now that transition from MFD is complete
- Enable KEY_LEFTMETA in new location on arm based cros-ec-keyboard
keymap"
* tag 'tag-chrome-platform-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
ARM: dts: cros-ec-keyboard: Add alternate keymap for KEY_LEFTMETA
platform/chrome: Use kobj_to_dev() instead of container_of()
platform/chrome: cros_ec_proto: Drop cros_ec_cmd_xfer()
platform/chrome: cros_ec_proto: Update cros_ec_cmd_xfer() call-sites
platform/chrome: Kconfig: Remove the transitional MFD_CROS_EC config
platform/chrome: cros_ec_lightbar: Reduce ligthbar get version command
platform/chrome: cros_ec_trace: Add fields to command traces
platform/chrome: cros_ec_typec: Re-order connector configuration steps
platform/chrome: cros_ec_typec: Avoid setting usb role twice during disconnect
platform/chrome: cros_ec_typec: Send enum values to usb_role_switch_set_role()
platform/chrome: cros_ec_typec: USB4 support
pwm: cros-ec: Simplify EC error handling
platform/chrome: cros_ec_proto: Convert EC error codes to Linux error codes
platform/input: cros_ec: Replace -ENOTSUPP with -ENOPROTOOPT
pwm: cros-ec: Accept more error codes from cros_ec_cmd_xfer_status
platform/chrome: cros_ec_sysfs: Report range of error codes from EC
cros_ec_lightbar: Accept more error codes from cros_ec_cmd_xfer_status
iio: cros_ec: Accept -EOPNOTSUPP as 'not supported' error code
When starting a HP machine with HIL driver but without an HIL keyboard
or HIL mouse attached, it may happen that data written to the HIL loop
gets stuck (e.g. because the transaction queue is full). Usually one
will then have to reboot the machine because all you see is and endless
output of:
Transaction add failed: transaction already queued?
In the higher layers hp_sdc_enqueue_transaction() is called to queued up
a HIL packet. This function returns an error code, and this patch adds
the necessary checks for this return code and disables the HIL driver if
further packets can't be sent.
Tested on a HP 730 and a HP 715/64 machine.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: <stable@vger.kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAl+FqrsTHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXnN8B/4sRg7j9OTzVBlDiXF2vj6vbuplTIH6
JR6S5f4PNjUg4gV6ghzSnsx1zqNhPSOr78zDqYto8vv+wqqj3thmld8+gAnSbKtt
yoAa7mhbbN1ryJiwPlZzvX4ApzGZPC7byqEi3+zPIcag6TEl8eyYJOmvY3x1zv8x
CsAb57oCC4erD0n4xlTyfuc8TLpO+EiU53PXbR9AovKQHe4m2/8LWyEbmrm5cRUR
gx8RxoLkkrqK0unzcmanbm47QodiaOTUpycs3IvaBeWZQsqSgFZdI1RAdTZNg+U+
GT8eMRXAwpgDpilPm/0n1O0PKGAsVh9Lbw8Btb/ggqnjTUlA4Z3Df23E
=Wy5n
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V updates from Wei Liu:
- a series from Boqun Feng to support page size larger than 4K
- a few miscellaneous clean-ups
* tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
hv: clocksource: Add notrace attribute to read_hv_sched_clock_*() functions
x86/hyperv: Remove aliases with X64 in their name
PCI: hv: Document missing hv_pci_protocol_negotiation() parameter
scsi: storvsc: Support PAGE_SIZE larger than 4K
Driver: hv: util: Use VMBUS_RING_SIZE() for ringbuffer sizes
HID: hyperv: Use VMBUS_RING_SIZE() for ringbuffer sizes
Input: hyperv-keyboard: Use VMBUS_RING_SIZE() for ringbuffer sizes
hv_netvsc: Use HV_HYP_PAGE_SIZE for Hyper-V communication
hv: hyperv.h: Introduce some hvpfn helper functions
Drivers: hv: vmbus: Move virt_to_hvpfn() to hyperv header
Drivers: hv: Use HV_HYP_PAGE in hv_synic_enable_regs()
Drivers: hv: vmbus: Introduce types of GPADL
Drivers: hv: vmbus: Move __vmbus_open()
Drivers: hv: vmbus: Always use HV_HYP_PAGE_SIZE for gpadl
drivers: hv: remove cast from hyperv_die_event
All evdev clients share a common waitgroup. On new input events, all
clients waiting on this waitgroup are woken up, even those filtering out
the events, possibly more than once per event. This leads to duplicated
and unwanted wakeups.
Split the shared waitgroup into per-client waitgroups for more
fine-grained wakeups.
Signed-off-by: Kenny Levinsen <kl@kl.wtf>
Link: https://lore.kernel.org/r/20200429184126.2155-1-kl@kl.wtf
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
With the new RMI4 F3A support, we're now able to enable full RMI4
support for this model. We also tidy up the comments a bit, as the X1E
is essentially the same computer as the P1.
Acked-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://lore.kernel.org/r/20200930225046.173190-3-Jason@zx2c4.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
With the recent addition of the F3A support, we can now accept
bootloader v8, which will help support recent Thinkpads.
Acked-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://lore.kernel.org/r/20200930225046.173190-2-Jason@zx2c4.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
RMI4 F3A supports the touchpad GPIO function, it's designed to
support more GPIOs and used on newer touchpads. This patch adds
support of the touchpad buttons.
Signed-off-by: Vincent Huang <vincent.huang@tw.synaptics.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Link: https://lore.kernel.org/r/20200930094147.635556-3-vincent.huang@tw.synaptics.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
f30_data in rmi_device_platform_data could be also referenced by RMI
function 3A, so rename it and the structure name to avoid confusion.
Signed-off-by: Vincent Huang <vincent.huang@tw.synaptics.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Link: https://lore.kernel.org/r/20200930094147.635556-2-vincent.huang@tw.synaptics.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for the bt541 touchscreen IC from zinitix, loosely based on
downstream driver. The driver currently supports multitouch (5 touch points).
The bt541 seems to support touch keys, but the support was not added because
that functionality is not being utilized by the touchscreen used for testing.
Based on the similartities between downstream drivers, it seems likely that
other similar touchscreen ICs can be supported with this driver in the future.
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
Link: https://lore.kernel.org/r/20201001122949.16846-1-michael.srba@seznam.cz
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"A couple more driver quirks, now enabling newer trackpoints from
Synaptics for real"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add nopnp quirk for Acer Aspire 5 A515
Input: trackpoint - enable Synaptics trackpoints
Touchpad on this laptop is not detected properly during boot, as PNP
enumerates (wrongly) AUX port as disabled on this machine.
Fix that by adding this board (with admittedly quite funny DMI
identifiers) to nopnp quirk list.
Reported-by: Andrés Barrantes Silman <andresbs2000@protonmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Link: https://lore.kernel.org/r/nycvar.YFH.7.76.2009252337340.3336@cbobk.fhfr.pm
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add Synaptics IDs in trackpoint_start_protocol() to mark them as valid.
Signed-off-by: Vincent Huang <vincent.huang@tw.synaptics.com>
Fixes: 6c77545af1 ("Input: trackpoint - add new trackpoint variant IDs")
Reviewed-by: Harry Cutts <hcutts@chromium.org>
Tested-by: Harry Cutts <hcutts@chromium.org>
Link: https://lore.kernel.org/r/20200924053013.1056953-1-vincent.huang@tw.synaptics.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For a Hyper-V vmbus, the size of the ringbuffer has two requirements:
1) it has to take one PAGE_SIZE for the header
2) it has to be PAGE_SIZE aligned so that double-mapping can work
VMBUS_RING_SIZE() could calculate a correct ringbuffer size which
fulfills both requirements, therefore use it to make sure vmbus work
when PAGE_SIZE != HV_HYP_PAGE_SIZE (4K).
Note that since the argument for VMBUS_RING_SIZE() is the size of
payload (data part), so it will be minus 4k (the size of header when
PAGE_SIZE = 4k) than the original value to keep the ringbuffer total
size unchanged when PAGE_SIZE = 4k.
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Cc: Michael Kelley <mikelley@microsoft.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20200916034817.30282-9-boqun.feng@gmail.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
platform_get_irq() returns -ERRNO on error. In such case comparison
to 0 would pass the check.
Fixes: e443631d20 ("Input: serio - add support for Alwinner A10/A20 PS/2 controller")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200828145744.3636-4-krzk@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
platform_get_irq() returns -ERRNO on error. In such case casting to
unsigned and comparing to 0 would pass the check.
Fixes: 7abf38d6d1 ("Input: twl4030-keypad - add device tree support")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200828145744.3636-3-krzk@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
platform_get_irq() returns -ERRNO on error. In such case comparison
to 0 would pass the check.
Fixes: f3a1ba60db ("Input: omap4-keypad - use platform device helpers")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200828145744.3636-2-krzk@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
platform_get_irq() returns -ERRNO on error. In such case comparison
to 0 would pass the check.
Fixes: 60214f058f ("Input: ep93xx_keypad - update driver to new core support")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200828145744.3636-1-krzk@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In stmfts_sysfs_hover_enable_write(), we should check value and
sdata->hover_enabled is all true.
Fixes: 78bcac7b2a ("Input: add support for the STMicroelectronics FingerTip touchscreen")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20200916141941.16684-1-yuehaibing@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If imx6ul_tsc_init() fails then we need to clean up the clocks.
I reversed the "if (input_dev->users) {" condition to make the code a
bit simpler.
Fixes: 6cc527b058 ("Input: imx6ul_tsc - propagate the errors")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200905124942.GC183976@mwanda
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds a new behavior to report touch major resolution
based on information provided by firmware.
In initial process, driver acquires touch information from touch ic.
It contains one byte about the resolution value of ABS_MT_TOUCH_MAJOR.
Touch driver will report touch major resolution by this information.
Signed-off-by: Johnny Chuang <johnny.chuang.emc@gmail.com>
Reviewed-by: Harry Cutts <hcutts@chromium.org>
Link: https://lore.kernel.org/r/1598581195-9874-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On an AMD chromebook, where the same I2C bus is shared by both Raydium
touchscreen and a trackpad device, it is observed that interleaving of
I2C messages when `raydium_i2c_read_message()` is called leads to the
Raydium touch IC reporting incorrect information. This is the sequence
that was observed to result in the above issue:
* I2C write to Raydium device for RM_CMD_BANK_SWITCH
* I2C write to trackpad device
* I2C read from trackpad device
* I2C write to Raydium device for setting address
* I2C read from Raydium device >>>> This provides incorrect
information
This change adds a new helper function `raydium_i2c_xfer()` that
performs I2C transactions to the Raydium device. It uses the register
address to decide if RM_CMD_BANK_SWITCH header needs to be sent to the
device (i.e. if register address is greater than 255, then bank switch
header is sent before the rest of the transaction). Additionally, it
ensures that all the I2C operations performed as part of
`raydium_i2c_xfer()` are done as a single i2c_transfer. This
guarantees that no other transactions are initiated to any other
device on the same bus in between. Additionally,
`raydium_i2c_{send|read}*` functions are refactored to use this new
helper function.
Verified with the patch across multiple reboots (>100) that the
information reported by the Raydium touchscreen device during probe
is correct.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Link: https://lore.kernel.org/r/20200821024006.3399663-1-furquan@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some 2-in-1s which use the soc_button_array driver have this ugly issue in
their DSDT where the _LID method modifies the irq-type settings of the
GPIOs used for the power and home buttons. The intend of this AML code is
to disable these buttons when the lid is closed.
The AML does this by directly poking the GPIO controllers registers. This
is problematic because when re-enabling the irq, which happens whenever
_LID gets called with the lid open (e.g. on boot and on resume), it sets
the irq-type to IRQ_TYPE_LEVEL_LOW. Where as the gpio-keys driver programs
the type to, and expects it to be, IRQ_TYPE_EDGE_BOTH.
This commit adds a workaround for this which (on affected devices) does
not set gpio_keys_button.gpio on these 2-in-1s, instead it gets the irq for
the GPIO, configures it as IRQ_TYPE_LEVEL_LOW (to match how the _LID AML
code configures it) and passes the irq in gpio_keys_button.irq.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200906122016.4628-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to the Microsoft documentation for Windows 8 convertible
devices, these devices should implement a PNP0C60 "laptop/slate mode state
indicator" ACPI device.
This device can work in 2 ways, if there is a GPIO which directly
indicates the device is in tablet-mode or not then the direct-gpio mode
should be used. If there is no such GPIO, but instead the events are
coming from e.g. the embedded-controller, then there should still be
a PNP0C60 ACPI device and event-injection should be used to send the
events. The drivers/platform/x86/intel-vbtn.c code is an example from
a standardized manner of doing the latter.
On various 2-in-1s with either a detachable keyboard, or with 360°
hinges, the direct GPIO mode is indicated by an ACPI device with a
HID of INT33D3, which contains a single GpioInt in its ACPI resource
table, which directly indicates if the device is in tablet-mode or not.
This commit adds support for this to the soc_button_array code, as
well as for the alternative ID9001 HID which some devices use
instead of the INT33D3 HID.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200826150601.12137-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is a preparation patch for adding support for Intel INT33D3
ACPI devices. These INT33D3 devices follow yet another Intel defined
(but not documented) ACPI GPIO button standard.
Unlike the ACPI GPIO button devices supported so far, the GPIO used in
the INT33D3 devices is active-high, rather then active-low.
This commit makes setting the gpio_keys_button.active_low flag
configurable through the soc_button_info struct and enables it for all
currently supported devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200826150601.12137-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
-----BEGIN PGP SIGNATURE-----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=bjMI
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc
Samsung S3C24xx and S3C64xx machine code cleanup for v5.10
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
* tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits)
ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup
ARM: s3c: Cleanup from old plat-samsung include
ARM: s3c: make headers local if possible
ARM: s3c: move into a common directory
ARM: s3c24xx: stop including mach/hardware.h from mach/io.h
cpufreq: s3c24xx: move low-level clk reg access into platform code
cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh
ARM: s3c: remove cpufreq header dependencies
cpufreq: s3c24xx: split out registers
fbdev: s3c2410fb: remove mach header dependency
ARM: s3c24xx: bast: avoid irq_desc array usage
ARM: s3c24xx: spi: avoid hardcoding fiq number in driver
ARM: s3c24xx: include mach/irqs.h where needed
ARM: s3c24xx: move s3cmci pinctrl handling into board files
ARM: s3c24xx: move iis pinctrl config into boards
ARM: s3c24xx: move spi fiq handler into platform
ARM: s3c: adc: move header to linux/soc/samsung
ARM: s3c24xx: move irqchip driver back into platform
ARM: s3c24xx: move regs-spi.h into spi driver
ARM: s3c64xx: remove mach/hardware.h
...
Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
-ENOTSUPP is not a SUSV4 error code and should not be used. Use
-ENOPROTOOPT instead to report EC_RES_INVALID_VERSION responses
from the EC. This matches match the NFS response for unsupported
protocol versions.
Cc: Gwendal Grignou <gwendal@chromium.org>
Cc: Yu-Hsuan Hsu <yuhsuan@chromium.org>
Cc: Prashant Malani <pmalani@chromium.org>
Cc: Brian Norris <briannorris@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
There are multiple drivers using the private adc interface.
It seems unlikely that they would ever get converted to iio,
so make the current state official by making the header file
global.
The s3c2410_ts driver needs a couple of register definitions
as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-22-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
changes to arch/sh.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJfODUiAAoJELcQ+SIFb8Hau0wH/iPeZyv0EhIwL41OPrWhm5wb
26MNWPvPjYIpKVpr0HMXiffILv595ntvrH0Ujnh1+e8J2kRj0eT+T91UkoyGSfav
oWmjgcG3NRK6p9882Oo8Xavjr1cTTclOmmDInR4lpAcfIBXkeq2eX0R1h2IuGdNM
idGlXhJMkgV+xTlgZy7pYmw5pvFMqL5j7fAUQxm0UoY9kbu8Ac4bOR5WrqtFpkjt
xTh9141YvSSfpRx9uMzrQLuUYGzGePhnjUGSUf/b1deYG/33lNtzhHr+QMK6BpXr
zdhFalJP40+m+2tG0nCBpAIZcWiOLGb23in5n/trFx3BGZfUf5EKnhZEGUYeE7Q=
=XWDn
-----END PGP SIGNATURE-----
Merge tag 'sh-for-5.9' of git://git.libc.org/linux-sh
Pull arch/sh updates from Rich Felker:
"Cleanup, SECCOMP_FILTER support, message printing fixes, and other
changes to arch/sh"
* tag 'sh-for-5.9' of git://git.libc.org/linux-sh: (34 commits)
sh: landisk: Add missing initialization of sh_io_port_base
sh: bring syscall_set_return_value in line with other architectures
sh: Add SECCOMP_FILTER
sh: Rearrange blocks in entry-common.S
sh: switch to copy_thread_tls()
sh: use the generic dma coherent remap allocator
sh: don't allow non-coherent DMA for NOMMU
dma-mapping: consolidate the NO_DMA definition in kernel/dma/Kconfig
sh: unexport register_trapped_io and match_trapped_io_handler
sh: don't include <asm/io_trapped.h> in <asm/io.h>
sh: move the ioremap implementation out of line
sh: move ioremap_fixed details out of <asm/io.h>
sh: remove __KERNEL__ ifdefs from non-UAPI headers
sh: sort the selects for SUPERH alphabetically
sh: remove -Werror from Makefiles
sh: Replace HTTP links with HTTPS ones
arch/sh/configs: remove obsolete CONFIG_SOC_CAMERA*
sh: stacktrace: Remove stacktrace_ops.stack()
sh: machvec: Modernize printing of kernel messages
sh: pci: Modernize printing of kernel messages
...
As of commit 37744feebc ("sh: remove sh5 support"), support for
the SH5-based Cayman platform can no longer be selected.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rich Felker <dalias@libc.org>
Pull input updates from Dmitry Torokhov:
- an update to Elan touchpad controller driver supporting newer ICs
with enhanced precision reports and a new firmware update process
- an update to EXC3000 touch controller supporting additional parts
- assorted driver fixups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (27 commits)
Input: exc3000 - add support to query model and fw_version
Input: exc3000 - add reset gpio support
Input: exc3000 - add EXC80H60 and EXC80H84 support
dt-bindings: touchscreen: Convert EETI EXC3000 touchscreen to json-schema
Input: sentelic - fix error return when fsp_reg_write fails
Input: alps - remove redundant assignment to variable ret
Input: ims-pcu - return error code rather than -ENOMEM
Input: elan_i2c - add ic type 0x15
Input: atmel_mxt_ts - only read messages in mxt_acquire_irq() when necessary
Input: uinput - fix typo in function name documentation
Input: ati_remote2 - add missing newlines when printing module parameters
Input: psmouse - add a newline when printing 'proto' by sysfs
Input: synaptics-rmi4 - drop a duplicated word
Input: elan_i2c - add support for high resolution reports
Input: elan_i2c - do not constantly re-query pattern ID
Input: elan_i2c - add firmware update info for ICs 0x11, 0x13, 0x14
Input: elan_i2c - handle firmware updated on newer ICs
Input: elan_i2c - add support for different firmware page sizes
Input: elan_i2c - fix detecting IAP version on older controllers
Input: elan_i2c - handle devices with patterns above 1
...
Expose model and fw_version via sysfs. Also query the model
in probe to make sure, that the I2C communication with the
device works before successfully probing the driver.
This is a bit complicated, since EETI devices do not have
a sync interface. Sending the commands and directly reading
does not work. Sending the command and waiting for some time
is also not an option, since there might be touch events in
the mean time.
Last but not least we do not cache the results, since this
interface can be used to check the I2C communication is still
working as expected.
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20200805160520.456570-5-sebastian.reichel@collabora.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add basic support for an optional reset gpio.
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200805160520.456570-4-sebastian.reichel@collabora.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds support for EXC80H60 and EXCH84 controllers, which
use a different event type id and have two extra bits for the
resolution (so the maximum is 16K instead of 4K).
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200805160520.456570-3-sebastian.reichel@collabora.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently when the call to fsp_reg_write fails -EIO is not being returned
because the count is being returned instead of the return value in retval.
Fix this by returning the value in retval instead of count.
Addresses-Coverity: ("Unused value")
Fixes: fc69f4a6af ("Input: add new driver for Sentelic Finger Sensing Pad")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200603141218.131663-1-colin.king@canonical.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The variable ret is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200603135742.130852-1-colin.king@canonical.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently the assignment of -ENOMEM to error is redundant because error
is not being read and -ENOMEM is being hard coded as an error return.
Fix this by returning the error code in variable 'error'; this also
allows the error code from a failed call to input_register_device to
be preserved and returned to the caller rather than just returning
a possibly inappropriate -ENOMEM.
Kudos to Dan Carpenter for the suggestion of an improved fix.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200603152151.139337-1-colin.king@canonical.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here is the large set of Staging and IIO driver patches for 5.9-rc1.
Lots of churn here, but overall the size increase in lines added is
small, while adding a load of new IIO drivers.
Major things in here:
- lots and lots of IIO new drivers and frameworks added
- IIO driver fixes and updates
- lots of tiny coding style cleanups for staging drivers
- vc04_services major reworks and cleanups
We had 3 set of drivers move out of staging in this round as well:
- wilc1000 wireless driver moved out of staging
- speakup moved out of staging
- most USB driver moved out of staging
Full details are in the shortlog.
All of these have been in linux-next with no reported issues. The last
few changes here were to resolve reported linux-next issues, and they
seem to have resolved the problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXyv2rA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yngIgCfZOVj022X+paV81NwvO/TroMDA7oAn1C4XCmY
Fxz55oHIyk9lbQxsDhID
=ujqG
-----END PGP SIGNATURE-----
Merge tag 'staging-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO driver updates from Greg KH:
"Here is the large set of Staging and IIO driver patches for 5.9-rc1.
Lots of churn here, but overall the size increase in lines added is
small, while adding a load of new IIO drivers.
Major things in here:
- lots and lots of IIO new drivers and frameworks added
- IIO driver fixes and updates
- lots of tiny coding style cleanups for staging drivers
- vc04_services major reworks and cleanups
We had 3 set of drivers move out of staging in this round as well:
- wilc1000 wireless driver moved out of staging
- speakup moved out of staging
- most USB driver moved out of staging
Full details are in the shortlog.
All of these have been in linux-next with no reported issues. The last
few changes here were to resolve reported linux-next issues, and they
seem to have resolved the problems"
* tag 'staging-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (428 commits)
staging: most: fix up movement of USB driver
staging: rts5208: clear alignment style issues
staging: r8188eu: replace rtw_netdev_priv define with inline function
staging: netlogic: clear alignment style issues
staging: android: ashmem: Fix lockdep warning for write operation
drivers: most: add USB adapter driver
staging: most: Use %pM format specifier for MAC addresses
staging: ks7010: Use %pM format specifier for MAC addresses
staging: qlge: qlge_dbg: removed comment repition
staging: wfx: Use flex_array_size() helper in memcpy()
staging: rtl8723bs: Align macro definitions
staging: rtl8723bs: Clean up function declations
staging: rtl8723bs: Fix coding style errors
drivers: staging: audio: Fix the missing header file for helper file
staging: greybus: audio: Enable GB codec, audio module compilation.
staging: greybus: audio: Add helper APIs for dynamic audio modules
staging: greybus: audio: Resolve compilation error in topology parser
staging: greybus: audio: Resolve compilation errors for GB codec module
staging: greybus: audio: Maintain jack list within GB Audio module
staging: greybus: audio: Update snd_jack FW usage as per new APIs
...
- Prepare for tasklet API modernization (Romain Perier, Allen Pais, Kees Cook)
-----BEGIN PGP SIGNATURE-----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=hb+e
-----END PGP SIGNATURE-----
Merge tag 'tasklets-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull tasklets API update from Kees Cook:
"These are the infrastructure updates needed to support converting the
tasklet API to something more modern (and hopefully for removal
further down the road).
There is a 300-patch series waiting in the wings to get set out to
subsystem maintainers, but these changes need to be present in the
kernel first. Since this has some treewide changes, I carried this
series for -next instead of paining Thomas with it in -tip, but it's
got his Ack.
This is similar to the timer_struct modernization from a while back,
but not nearly as messy (I hope). :)
- Prepare for tasklet API modernization (Romain Perier, Allen Pais,
Kees Cook)"
* tag 'tasklets-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
tasklet: Introduce new initialization API
treewide: Replace DECLARE_TASKLET() with DECLARE_TASKLET_OLD()
usb: gadget: udc: Avoid tasklet passing a global
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEeOVYVaWZL5900a/pOQOGJssO/ZEFAl8eiUATHHJwcHRAbGlu
dXguaWJtLmNvbQAKCRA5A4Ymyw79kWs8B/4wEWVJGTkjyrMX57/Ew8yRYAJE6JjA
kSONPjElVrPR1pRLYyjyde+zqumkJFhk+41De09J2byL29p7tK8ISNrTwJrIN7n/
dzT73CmuNEjI0rZJxPX+USKFph75FQVvAVOOWs+6fiBFxdUaIsBheVntH7/NsCTk
HFrIjIn5wXFVs5Nh+2cHydvEpOVoUWzjvs+uJIEpHCVCBz6gaYq2dxEmeTquKuz1
k7PZqCqVsyB9iWLqN65/Q+30N8znJwcUl8HAzs5nvPrXLjGxwuEjOxtYYhbdLAfP
OBiIF9J77sZxBlms0WNomDW3Rr5Vlt5nF9oUWpi3AmHNWIuX0GkM4i0C
=V+Kl
-----END PGP SIGNATURE-----
Merge tag 'rm-unicore32' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/linux
Pull unicore32 removal from Mike Rapoport:
"Remove unicore32 support.
The unicore32 port do not seem maintained for a long time now, there
is no upstream toolchain that can create unicore32 binaries and all
the links to prebuilt toolchains for unicore32 are dead. Even
compilers that were available are not supported by the kernel anymore.
Guenter Roeck says:
"I have stopped building unicore32 images since v4.19 since there is
no available compiler that is still supported by the kernel. I am
surprised that support for it has not been removed from the kernel"
However, it's worth pointing out two things:
- Guan Xuetao is still listed as maintainer and asked for the port to
be kept around the last time Arnd suggested removing it two years
ago. He promised that there would be compiler sources (presumably
llvm), but has not made those available since.
- https://github.com/gxt has patches to linux-4.9 and qemu-2.7, both
released in 2016, with patches dated early 2019. These patches
mainly restore a syscall ABI that was never part of mainline Linux
but apparently used in production. qemu-2.8 removed support for
that ABI and newer kernels (4.19+) can no longer be built with the
old toolchain, so apparently there will not be any future updates
to that git tree"
* tag 'rm-unicore32' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/linux:
MAINTAINERS: remove "PKUNITY SOC DRIVERS" entry
rtc: remove fb-puv3 driver
video: fbdev: remove fb-puv3 driver
pwm: remove pwm-puv3 driver
input: i8042: remove support for 8042-unicore32io
i2c/buses: remove i2c-puv3 driver
cpufreq: remove unicore32 driver
arch: remove unicore32 port
This converts all the existing DECLARE_TASKLET() (and ...DISABLED)
macros with DECLARE_TASKLET_OLD() in preparation for refactoring the
tasklet callback type. All existing DECLARE_TASKLET() users had a "0"
data argument, it has been removed here as well.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
The workaround of reading all messages until an invalid is received is a
way of forcing the CHG line high, which means that when using
edge-triggered interrupts the interrupt can be acquired.
With level-triggered interrupts the workaround is unnecessary.
Also, most recent maXTouch chips have a feature called RETRIGEN which, when
enabled, reasserts the interrupt line every cycle if there are messages
waiting. This also makes the workaround unnecessary.
Note: the RETRIGEN feature is only in some firmware versions/chips, it's
not valid simply to enable the bit.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
(cherry picked from ndyer/linux/for-upstream commit 1ae4e8281e491b22442cd5acdfca1862555f8ecb)
[gdavis: Fix conflicts due to v4.6-rc7 commit eb43335c40 ("Input:
atmel_mxt_ts - use mxt_acquire_irq in mxt_soft_reset").]
Signed-off-by: George G. Davis <george_davis@mentor.com>
[jiada: reset use_retrigen_workaround at beginning of mxt_check_retrigen()
call mxt_check_retrigen() after mxt_acquire_irq() in mxt_initialize()
replace white-spaces with tab for MXT_COMMS_RETRIGEN
Changed to check if IRQ is level type]
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Link: https://lore.kernel.org/r/20200727151637.23810-1-jiada_wang@mentor.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When I cat some module parameters by sysfs, it displays as follows. It's
better to add a newline for easy reading.
root@syzkaller:~# cat /sys/module/ati_remote2/parameters/mode_mask
0x1froot@syzkaller:~# cat /sys/module/ati_remote2/parameters/channel_mask
0xffffroot@syzkaller:~#
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/20200720092148.9320-1-wangxiongfeng2@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When I cat parameter 'proto' by sysfs, it displays as follows. It's
better to add a newline for easy reading.
root@syzkaller:~# cat /sys/module/psmouse/parameters/proto
autoroot@syzkaller:~#
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Link: https://lore.kernel.org/r/20200720073846.120724-1-wangxiongfeng2@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Newer controllers (identified as "pattern" version 2) send higher
resolution reports, with 16-bit X and Y coordinates (previous generations
used 12-bit values). These new high resolution reports use report ID of
0x60.
SMbus controllers use the same buffer size for both the new and old
reports, and because of that high resolution reports no longer carry
area of contact data with SMbus.
Signed-off-by: Jingle Wu <jingle.wu@emc.com.tw>
Link: https://lore.kernel.org/r/20200710054116.5529-1-jingle.wu@emc.com.tw
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We do not need to constantly re-query pattern ID, we can instead query it
once and then pass to methods that need it.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl8UzA4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGQ7cH/3v+Gv+SmHJCvaT2
CSu0+7okVnYbY3UTb3hykk7/aOqb6284KjxR03r0CWFzsEsZVhC5pvvruASSiMQg
Pi04sLqv6CsGLHd1n+pl4AUYEaxq6k4KS3uU3HHSWxrahDDApQoRUx2F8lpOxyj8
RiwnoO60IMPA7IFJqzcZuFqsgdxqiiYvnzT461KX8Mrw6fyMXeR2KAj2NwMX8dZN
At21Sf8+LSoh6q2HnugfiUd/jR10XbfxIIx2lXgIinb15GXgWydEQVrDJ7cUV7ix
Jd0S+dtOtp+lWtFHDoyjjqqsMV7+G8i/rFNZoxSkyZqsUTaKzaR6JD3moSyoYZgG
0+eXO4A=
=9EpR
-----END PGP SIGNATURE-----
Merge 5.8-rc6 into staging-next
We need the staging fixes in here, and it resolves a merge issue with an
iio driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds firmware size and page sizes for ic types 0x11, 0x13 and 0x14.
IC 0x14 uses 512-byte firmware page size.
Signed-off-by: Jingle Wu <jingle.wu@emc.com.tw>.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Newer ICs with IC type value starting with 0x0D and newer bootloader code
use 128-byte firmware pages. Their bootloader also needs to be switched to
proper mode before executing firmware update.
Signed-off-by: Jingle Wu <jingle.wu@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Prepare driver for devices that use different sizes of firmware pages.
Signed-off-by: Jingle Wu <jingle.wu@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Extend fetching and parsing parameters of the controllers to devices with
"patterns" above 1 (which currently should be handled in the same fashion
as devices with pattern 1).
Signed-off-by: Jingle Wu <jingle.wu@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On older controllers IC type is reported in the 2nd byte of
ETP_I2C_OSM_VERSION_CMD, however if controller's firmware is not flashed
correctly it may return incorrect data. Fortunately there is also
ETP_I2C_IAP_VERSION_P0_CMD command that can be used when controller in
either normal or IAP mode, and which is guaranteed to return accurate data,
so let's use it.
Signed-off-by: Jingle Wu <jingle.wu@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Not all versions of firmware implement "get pattern" command. When
encountering those assume that the controllers use older pattern.
Signed-off-by: Jingle Wu <jingle.wu@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some new devices, but particularly good this time is the core rework coming
from Alexandru. Some of this has been in Analog's tree a long time, but other
parts are motivated by closing down common mistakes in new drivers.
Changes since first try at this pull request:
* Add missed patch to actually remove iio_priv_to_dev and as a result
also drop a few ingenic patches that need to be updated to take this
into account.
* Fix an ordering issue int he pollfunc attach in the core rework.
New device support
* qcom pmic7 adc
- New driver using common qcom-vadc library. Some associated cleanups and
refactors.
* invensense icm42600
- New driver supporting icm42600, icm42602, icm42605 and icm42622 via i2c
or spi. These are all 6 axis IMUs with gyro and accelerometers.
Driver supports buffered modes using the hardware fifo and interpolation
for accurate timestamps.
* sensirion scd30
- New driver for this carbon dioxide sensor including i2c and serial
interfaces + bindings.
Features
* ak8975
- Add reset gpio support.
* bma400
- Support SPI.
* bmc150
- Document and add support for bmc156b and bmm150b, tidy up _magn endings.
* bmi160
- Regulator and mount matrix support.
* mxc4005
- Add ID for mxc6655
* rockchip-saradc
- Triggered buffer support.
DT bindings
* qcom spmi-vadc converted to yaml + pmic7 bindings
* ak8975 tidy up and convert to yaml + add reset-gpio binding
* ingenic-adc -convert to yaml.
Core rework all carried through by Alexandru Ardelean.
* Assign parent device in the core rather than every driver. A few devices
need to provide specific non standard parents, so there is support for
overriding.
* Start to take parts of struct iio_dev opaque to the drivers.
This will be a long term job, but should reduce the number of drivers
we get that use parts that are currently only 'internal' by documentation.
* Move attach and detach of pollfunc to the core. Every triggered buffer
using driver had to do the same thing, so lets do it in the core. The
hard part here was getting all the drivers into canonical form so there
would be no functional changes in this final patch. That's taken quite
a lot of work over last couple of cycles!
Cleanups and minor fixes.
* docs
- Improve IIO_CONCENTRATION channel type description in ABI docs.
- Drop doubled word cases.
- Http to Https conversion.
* core
- Make iio_device_get_drvdata take a const struct iio_dev * avoiding some
nasty casts.
* ADCs
- Drop lots of users of of_match_ptr macro, includes of mod_devicetable.h
and CONFIG_OF protections. These prevent use of ACPI PRP0001 with these
drivers and get coppied into lots of new drivers.
* ad5380
- Constify iio_chan_spec_ext_info
* ad5592r
- Constify iio_chan_spec_ext_info
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* ad8366
- Make gpio optional as doesn't matter if its there or not.
* adis16480
- Use irq types instead of the flags.
* atlas-ezo-sensor
- Minimize scope of ret variable.
* at91-adc
- Add COMPILE_TEST dependency to driver to improve build coverage.
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* at91-sama5d2
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
- Drop Ludovic as a co-maintaienr.
* cros_ec
- Reapply the range after resume.
- Add a read only frequency entry for legacy version.
- Typo fixes
* hts221
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* inv_mpu
- Drop double check on ACPI companion device.
* iqs621
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* iqs624
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* max11100
- Constify iio_chan_spec
* mmc35240
- Constify reg_default
* rockchip-saradc
- Move to managed allocators for everything in probe.
- Use more distinctive prefix for channel macros.
* stk3310
- Constify regmap_config.
* stm32-adc
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* stm32-dfsdm-adc
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* ti-am335x
- Use managed allocations where straight forward in probe function.
* tsl2563
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
-----BEGIN PGP SIGNATURE-----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=LyRl
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.9a-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, cleanups and features for IIO in the 5.9 cycle
Some new devices, but particularly good this time is the core rework coming
from Alexandru. Some of this has been in Analog's tree a long time, but other
parts are motivated by closing down common mistakes in new drivers.
Changes since first try at this pull request:
* Add missed patch to actually remove iio_priv_to_dev and as a result
also drop a few ingenic patches that need to be updated to take this
into account.
* Fix an ordering issue int he pollfunc attach in the core rework.
New device support
* qcom pmic7 adc
- New driver using common qcom-vadc library. Some associated cleanups and
refactors.
* invensense icm42600
- New driver supporting icm42600, icm42602, icm42605 and icm42622 via i2c
or spi. These are all 6 axis IMUs with gyro and accelerometers.
Driver supports buffered modes using the hardware fifo and interpolation
for accurate timestamps.
* sensirion scd30
- New driver for this carbon dioxide sensor including i2c and serial
interfaces + bindings.
Features
* ak8975
- Add reset gpio support.
* bma400
- Support SPI.
* bmc150
- Document and add support for bmc156b and bmm150b, tidy up _magn endings.
* bmi160
- Regulator and mount matrix support.
* mxc4005
- Add ID for mxc6655
* rockchip-saradc
- Triggered buffer support.
DT bindings
* qcom spmi-vadc converted to yaml + pmic7 bindings
* ak8975 tidy up and convert to yaml + add reset-gpio binding
* ingenic-adc -convert to yaml.
Core rework all carried through by Alexandru Ardelean.
* Assign parent device in the core rather than every driver. A few devices
need to provide specific non standard parents, so there is support for
overriding.
* Start to take parts of struct iio_dev opaque to the drivers.
This will be a long term job, but should reduce the number of drivers
we get that use parts that are currently only 'internal' by documentation.
* Move attach and detach of pollfunc to the core. Every triggered buffer
using driver had to do the same thing, so lets do it in the core. The
hard part here was getting all the drivers into canonical form so there
would be no functional changes in this final patch. That's taken quite
a lot of work over last couple of cycles!
Cleanups and minor fixes.
* docs
- Improve IIO_CONCENTRATION channel type description in ABI docs.
- Drop doubled word cases.
- Http to Https conversion.
* core
- Make iio_device_get_drvdata take a const struct iio_dev * avoiding some
nasty casts.
* ADCs
- Drop lots of users of of_match_ptr macro, includes of mod_devicetable.h
and CONFIG_OF protections. These prevent use of ACPI PRP0001 with these
drivers and get coppied into lots of new drivers.
* ad5380
- Constify iio_chan_spec_ext_info
* ad5592r
- Constify iio_chan_spec_ext_info
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* ad8366
- Make gpio optional as doesn't matter if its there or not.
* adis16480
- Use irq types instead of the flags.
* atlas-ezo-sensor
- Minimize scope of ret variable.
* at91-adc
- Add COMPILE_TEST dependency to driver to improve build coverage.
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* at91-sama5d2
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
- Drop Ludovic as a co-maintaienr.
* cros_ec
- Reapply the range after resume.
- Add a read only frequency entry for legacy version.
- Typo fixes
* hts221
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* inv_mpu
- Drop double check on ACPI companion device.
* iqs621
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* iqs624
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* max11100
- Constify iio_chan_spec
* mmc35240
- Constify reg_default
* rockchip-saradc
- Move to managed allocators for everything in probe.
- Use more distinctive prefix for channel macros.
* stk3310
- Constify regmap_config.
* stm32-adc
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* stm32-dfsdm-adc
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* ti-am335x
- Use managed allocations where straight forward in probe function.
* tsl2563
- Avoid use of iio_priv_to_dev (precursor to taking parts of iio_dev opaque)
* tag 'iio-for-5.9a-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (107 commits)
iio: buffer: fix attach/detach pollfunc order
iio: core: remove iio_priv_to_dev() helper
Replace HTTP links with HTTPS ones: drivers/iio
Replace HTTP links with HTTPS ones: Documentation/devicetree/bindings/iio
dt-bindings: iio/adc: Convert ingenic-adc docs to YAML.
iio: cros_ec_accel_legacy: Add Read Only frequency entries
MAINTAINERS: adc: at91-sama5d2_adc: remove myself as co-maintainer
iio: adc: ti_am335x_adc: alloc kfifo & IRQ via devm_ functions
iio: adc: ti_am335x_adc: alloc channels via devm_kcalloc()
iio:adc:ingenic: drop of_match_ptr protection and include mod_devicetable.h
iio:adc:ti-tlc4541: Drop CONFIG_OF and of_match_ptr protections.
iio:adc:ti-adc161s626: Drop of_match_ptr protection.
iio:adc:ti-adc084s021: drop of_match_ptr protection
iio:adc:ti-adc0832: drop CONFIG_OF and of_match_ptr protections
iio:adc:ti-adc081c: Drop of_match_ptr and change to mod_devicetable.h
iio:adc:sd_adc_modulator: Drop of_match_ptr and tweak includes
iio:adc:mcp3422: remove CONFIG_OF and of_match_ptr protections
iio:adc:mcp320x: Drop CONFIG_OF and of_match_ptr protections
iio:adc:max1118: Drop CONFIG_OF / of_match_ptr protections
iio:adc:max11100: Drop of_match_ptr protection / add mod_devicetable.h include
...
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
Pull input fixes from Dmitry Torokhov:
"A few quirks for the Elan touchpad driver, another Thinkpad is being
switched over from PS/2 to native RMI4 interface, and we gave a brand
new SW_MACHINE_COVER switch definition"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - add more hardware ID for Lenovo laptops
Input: i8042 - add Lenovo XiaoXin Air 12 to i8042 nomux list
Revert "Input: elants_i2c - report resolution information for touch major"
Input: elan_i2c - only increment wakeup count on touch
Input: synaptics - enable InterTouch for ThinkPad X1E 1st gen
ARM: dts: n900: remove mmc1 card detect gpio
Input: add `SW_MACHINE_COVER`
This fixes two finger trackpad scroll on the Lenovo XiaoXin Air 12.
Without nomux, the trackpad behaves as if only one finger is present and
moves the cursor when trying to scroll.
Signed-off-by: David Pedersen <limero1337@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200625133754.291325-1-limero1337@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The variable error is being initialized with a value that is
never read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200603140431.131347-1-colin.king@canonical.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This reverts commit 0617067163 - it turns
out that the resolution of 1 unit per mm was not correct for a number of
touch screens, causing touch sizes to be reported as way too large.
See https://crbug.com/1085648
Reported-by: Harry Cutts <hcutts@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This moves the wakeup increment for elan devices to the touch report.
This prevents the drivers from incorrectly reporting a wakeup when the
resume callback resets then device, which causes an interrupt to
occur.
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Link: https://lore.kernel.org/r/20200706235046.1984283-1-dbasehore@chromium.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested on my own laptop, touchpad feels slightly more responsive with
this on, though it might just be placebo.
Signed-off-by: Ilya Katsnelson <me@0upti.me>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20200703143457.132373-1-me@0upti.me
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The unicore32 port is removed from the kernel.
There is no point to keep stale definitions to support this architecture.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
This patch applies the semantic patch:
@@
expression I, P, SP;
@@
I = devm_iio_device_alloc(P, SP);
...
- I->dev.parent = P;
It updates 302 files and does 307 deletions.
This semantic patch also removes some comments like
'/* Establish that the iio_dev is a child of the i2c device */'
But this is is only done in case where the block is left empty.
The patch does not seem to cover all cases. It looks like in some cases a
different variable is used in some cases to assign the parent, but it
points to the same reference.
In other cases, the block covered by ... may be just too big to be covered
by the semantic patch.
However, this looks pretty good as well, as it does cover a big bulk of the
drivers that should remove the parent assignment.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Pull input updates from Dmitry Torokhov:
- a new driver for the Azoteq IQS269A capacitive touch controller
- a new driver for the Cypress CY8CTMA140 touchscreen
- updates to Elan and ft5x06 touchscreen drivers
- assorted driver fixes
- msm-vibrator has been removed as we have a more generic solution
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (28 commits)
Input: adi - work around module name confict
Input: iqs269a - add missing I2C dependency
Input: elants - refactor elants_i2c_execute_command()
Input: elants - override touchscreen info with DT properties
Input: elants - remove unused axes
Input: add support for Azoteq IQS269A
dt-bindings: input: Add bindings for Azoteq IQS269A
Input: imx_sc_key - use devm_add_action_or_reset() to handle all cleanups
Input: remove msm-vibrator driver
dt-bindings: Input: remove msm-vibrator
Input: elants_i2c - provide an attribute to show calibration count
Input: introduce input_mt_report_slot_inactive()
dt-bindings: input: touchscreen: elants_i2c: convert to YAML
Input: add driver for the Cypress CY8CTMA140 touchscreen
dt-bindings: touchscreen: Add CY8CTMA140 bindings
Input: edt-ft5x06 - prefer asynchronous probe
Input: edt-ft5x06 - improve power management operations
Input: edt-ft5x06 - move parameter restore into helper
Input: edt-ft5x06 - fix get_default register write access
Input: atkbd - receive and use physcode->keycode mapping from FW
...
Making module name conflicts a fatal error breaks sparc64 allmodconfig:
Error log:
error: the following would cause module name conflict:
drivers/char/adi.ko
drivers/input/joystick/adi.ko
Renaming one of the modules would solve the problem, but then cause other
problems because neither of them is automatically loaded and changing
the name is likely to break any setup that relies on manually loading
it by name.
As there is probably no sparc64 system with this kind of ancient joystick
attached, work around it by adding a Kconfig dependency that forbids
them from both being modules. It is still possible to build the joystick
driver if the sparc64 adi driver is built-in.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200609100643.1245061-1-arnd@arndb.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- Support for userspace to send requests directly to the on-chip GZIP
accelerator on Power9.
- Rework of our lockless page table walking (__find_linux_pte()) to make it
safe against parallel page table manipulations without relying on an IPI for
serialisation.
- A series of fixes & enhancements to make our machine check handling more
robust.
- Lots of plumbing to add support for "prefixed" (64-bit) instructions on
Power10.
- Support for using huge pages for the linear mapping on 8xx (32-bit).
- Remove obsolete Xilinx PPC405/PPC440 support, and an associated sound driver.
- Removal of some obsolete 40x platforms and associated cruft.
- Initial support for booting on Power10.
- Lots of other small features, cleanups & fixes.
Thanks to:
Alexey Kardashevskiy, Alistair Popple, Andrew Donnellan, Andrey Abramov,
Aneesh Kumar K.V, Balamuruhan S, Bharata B Rao, Bulent Abali, Cédric Le
Goater, Chen Zhou, Christian Zigotzky, Christophe JAILLET, Christophe Leroy,
Dmitry Torokhov, Emmanuel Nicolet, Erhard F., Gautham R. Shenoy, Geoff Levand,
George Spelvin, Greg Kurz, Gustavo A. R. Silva, Gustavo Walbon, Haren Myneni,
Hari Bathini, Joel Stanley, Jordan Niethe, Kajol Jain, Kees Cook, Leonardo
Bras, Madhavan Srinivasan., Mahesh Salgaonkar, Markus Elfring, Michael
Neuling, Michal Simek, Nathan Chancellor, Nathan Lynch, Naveen N. Rao,
Nicholas Piggin, Oliver O'Halloran, Paul Mackerras, Pingfan Liu, Qian Cai, Ram
Pai, Raphael Moreira Zinsly, Ravi Bangoria, Sam Bobroff, Sandipan Das, Segher
Boessenkool, Stephen Rothwell, Sukadev Bhattiprolu, Tyrel Datwyler, Wolfram
Sang, Xiongfeng Wang.
-----BEGIN PGP SIGNATURE-----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=o0WU
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
- Support for userspace to send requests directly to the on-chip GZIP
accelerator on Power9.
- Rework of our lockless page table walking (__find_linux_pte()) to
make it safe against parallel page table manipulations without
relying on an IPI for serialisation.
- A series of fixes & enhancements to make our machine check handling
more robust.
- Lots of plumbing to add support for "prefixed" (64-bit) instructions
on Power10.
- Support for using huge pages for the linear mapping on 8xx (32-bit).
- Remove obsolete Xilinx PPC405/PPC440 support, and an associated sound
driver.
- Removal of some obsolete 40x platforms and associated cruft.
- Initial support for booting on Power10.
- Lots of other small features, cleanups & fixes.
Thanks to: Alexey Kardashevskiy, Alistair Popple, Andrew Donnellan,
Andrey Abramov, Aneesh Kumar K.V, Balamuruhan S, Bharata B Rao, Bulent
Abali, Cédric Le Goater, Chen Zhou, Christian Zigotzky, Christophe
JAILLET, Christophe Leroy, Dmitry Torokhov, Emmanuel Nicolet, Erhard F.,
Gautham R. Shenoy, Geoff Levand, George Spelvin, Greg Kurz, Gustavo A.
R. Silva, Gustavo Walbon, Haren Myneni, Hari Bathini, Joel Stanley,
Jordan Niethe, Kajol Jain, Kees Cook, Leonardo Bras, Madhavan
Srinivasan., Mahesh Salgaonkar, Markus Elfring, Michael Neuling, Michal
Simek, Nathan Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin,
Oliver O'Halloran, Paul Mackerras, Pingfan Liu, Qian Cai, Ram Pai,
Raphael Moreira Zinsly, Ravi Bangoria, Sam Bobroff, Sandipan Das, Segher
Boessenkool, Stephen Rothwell, Sukadev Bhattiprolu, Tyrel Datwyler,
Wolfram Sang, Xiongfeng Wang.
* tag 'powerpc-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (299 commits)
powerpc/pseries: Make vio and ibmebus initcalls pseries specific
cxl: Remove dead Kconfig options
powerpc: Add POWER10 architected mode
powerpc/dt_cpu_ftrs: Add MMA feature
powerpc/dt_cpu_ftrs: Enable Prefixed Instructions
powerpc/dt_cpu_ftrs: Advertise support for ISA v3.1 if selected
powerpc: Add support for ISA v3.1
powerpc: Add new HWCAP bits
powerpc/64s: Don't set FSCR bits in INIT_THREAD
powerpc/64s: Save FSCR to init_task.thread.fscr after feature init
powerpc/64s: Don't let DT CPU features set FSCR_DSCR
powerpc/64s: Don't init FSCR_DSCR in __init_FSCR()
powerpc/32s: Fix another build failure with CONFIG_PPC_KUAP_DEBUG
powerpc/module_64: Use special stub for _mcount() with -mprofile-kernel
powerpc/module_64: Simplify check for -mprofile-kernel ftrace relocations
powerpc/module_64: Consolidate ftrace code
powerpc/32: Disable KASAN with pages bigger than 16k
powerpc/uaccess: Don't set KUEP by default on book3s/32
powerpc/uaccess: Don't set KUAP by default on book3s/32
powerpc/8xx: Reduce time spent in allow_user_access() and friends
...
This causes a build error with CONFIG_WALNUT because kb_cs and kb_data
were removed in commit 917f0af9e5 ("powerpc: Remove arch/ppc and
include/asm-ppc").
ld.lld: error: undefined symbol: kb_cs
> referenced by i8042-ppcio.h:28 (drivers/input/serio/i8042-ppcio.h:28)
> input/serio/i8042.o:(__i8042_command) in archive drivers/built-in.a
> referenced by i8042-ppcio.h:28 (drivers/input/serio/i8042-ppcio.h:28)
> input/serio/i8042.o:(__i8042_command) in archive drivers/built-in.a
> referenced by i8042-ppcio.h:28 (drivers/input/serio/i8042-ppcio.h:28)
> input/serio/i8042.o:(__i8042_command) in archive drivers/built-in.a
ld.lld: error: undefined symbol: kb_data
> referenced by i8042.c:309 (drivers/input/serio/i8042.c:309)
> input/serio/i8042.o:(__i8042_command) in archive drivers/built-in.a
> referenced by i8042-ppcio.h:33 (drivers/input/serio/i8042-ppcio.h:33)
> input/serio/i8042.o:(__i8042_command) in archive drivers/built-in.a
> referenced by i8042.c:319 (drivers/input/serio/i8042.c:319)
> input/serio/i8042.o:(__i8042_command) in archive drivers/built-in.a
> referenced 15 more times
Presumably since nobody has noticed this for the last 12 years, there is
not anyone actually trying to use this driver so we can just remove this
special walnut code and use the generic header so it builds for all
configurations.
Fixes: 917f0af9e5 ("powerpc: Remove arch/ppc and include/asm-ppc")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20200518181043.3363953-1-natechancellor@gmail.com
The Lenovo Thinkpad T470s I own has a different touchpad with "LEN007a"
instead of the already included PNP ID "LEN006c". However, my touchpad
seems to work well without any problems using RMI. So this patch adds the
other PNP ID.
Signed-off-by: Dennis Kadioglu <denk@eclipso.email>
Link: https://lore.kernel.org/r/ff770543cd53ae818363c0fe86477965@mail.eclipso.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If CONFIG_INPUT_IQS269A is selected yet CONFIG_I2C is not, the build
fails. To solve this problem, add I2C as a dependency.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 04e49867fa ("Input: add support for Azoteq IQS269A")
Link: https://lore.kernel.org/r/1589809466-22748-1-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Allow overriding of information from hardware and support additional
common DT properties like axis inversion. This is required for eg.
Nexus 7 and TF300T where the programmed values in firmware differ
from reality.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
[moved "prop" before DMA buffer]
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/49ea996878264f7c8bde25204e4ddf4b1e85ae71.1587923061.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Driver only ever reports MT events and input_mt_init_slots() sets up
emulated axes already. Clear the capabilities not generated directly
and move MT axes setup, so they are visible by input_mt_init_slots().
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/d5eee8cd305adb144a11264d70da94f7b6570366.1587923061.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use devm_add_action_or_reset() to handle all cleanups of failure in
.probe and .remove, then .remove callback can be dropped.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1584082751-17047-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The address referenced by this driver is within the Qualcomm Clock
namespace so let's drop the msm-vibrator bindings so that a more generic
solution can be used instead. No one is currently using driver so this
won't affect any users.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Link: https://lore.kernel.org/r/20200513013140.69935-3-masneyb@onstation.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is an non-touch case by non-calibration after update firmware.
Elan could know calibrate or not by calibration count.
The value of '0xffff' means we didn't calibrate after update firmware.
If calibrate success, it will plus one and change to '0x0000'.
Signed-off-by: Johnny Chuang <johnny.chuang@emc.com.tw>
Link: https://lore.kernel.org/r/1588754932-5902-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_mt_report_slot_state() ignores "tool" argument when the slot is
closed, which has caused a bit of confusion. Let's introduce
input_mt_report_slot_inactive() to report inactive slot state.
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Link: https://lore.kernel.org/r/20200508055656.96389-2-jiada_wang@mentor.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl6BIG4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGlHUH/RCFve2sfHRPjRW+
xR5SaLVAw6XKvtKBq7yvKmHEwqNJnL79IHyqqtSrtfFr2FfaH/KvYiCbbAezvSrM
np0udGu7STKGd21CWuyEZJudyhXkOwMRNiFiCXWp7rs35oh8T0TpJxMzo2Nc1nLk
JFQPqAP6OSvq4IkWEywKQI+Au3Z1IBf83xVjZ1s+MKPQHYD49x2hc4cQntL5/cnm
a3DoR2iBkYiGZCZ9dDqAqJTnMQIiCbACdZXgGjNRUpdyA/dtAjsMl11NPYHm8TA2
3AHBupAK50WBZGad6xv2qKQyScsmoJG2mv92QjlOFz0Tpiu6rLnDlLYREDVB6YH6
qbLDsc8=
=XEIU
-----END PGP SIGNATURE-----
Merge tag 'v5.6' into next
Sync up with mainline to get device tree and other changes.
This adds a new driver for the Cypress CY8CTMA140 touchscreen.
This driver is inspired by out-of-tree code for the Samsung
GT-S7710 mobile phone.
I have tried to compare the structure and behaviour of this
touchscreen to the existing CYTTSP and CYTTSP4 generics and
it seems pretty different. It is also different in character
from the cy8ctmg110_ts.c. It appears to rather be vaguely
related to the Melfas MMS114 driver, yet distinctly
different.
Dmitry Torokhov rewrote the key scanning code during the
submission process so the driver is a joint work.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200506123435.187432-2-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20200507185347.GA14499@embeddedor
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Probing the device takes a while, because we sleep for 300 ms after a
reset; allow asynchronous probing so this can happen in the background
while other devices are being probed.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20200227112819.16754-5-m.felsch@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We need to restore the parameters if we switch between the
factory/work mode and during the resume process if we switched off the
power-supply. Therefore refactor edt_ft5x06_work_mode() and move the
"restore the parameters" into a helper routine so we can reuse it later.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20200227112819.16754-3-m.felsch@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since commit b6eba86030 ("Input: edt-ft5x06 - add offset support for
ev-ft5726") offset-x and offset-y is supported. Devices using those
offset parameters don't support the offset parameter so we need to add
the NO_REGISTER check for edt_ft5x06_ts_get_defaults().
Fixes: b6eba86030 ("Input: edt-ft5x06 - add offset support for ev-ft5726")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20200227112819.16754-2-m.felsch@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On some X86 devices we do not register an input-device, because the
power-button is also handled by the soc_button_array (GPIO) input driver,
and we want to avoid reporting power-button presses to userspace twice.
Sofar when we did this we also did not register our interrupt handlers,
since those were only necessary to report input events.
But on at least 2 device models the Medion Akoya E1239T and the GPD win,
the GPIO pin used by the soc_button_array driver for the power-button
cannot wakeup the system from suspend. Why this does not work is not clear,
I've tried comparing the value of all relevant registers on the Cherry
Trail SoC, with those from models where this does work. I've checked:
PMC registers: FUNC_DIS, FUNC_DIS2, SOIX_WAKE_EN, D3_STS_0, D3_STS_1,
D3_STDBY_STS_0, D3_STDBY_STS_1; PMC ACPI I/O regs: PM1_STS_EN, GPE0a_EN
and they all have identical contents in the working and non working cases.
I suspect that the firmware either sets some unknown register to a value
causing this, or that it turns off a power-plane which is necessary for
GPIO wakeups to work during suspend.
What does work on the Medion Akoya E1239T is letting the AXP288 wakeup
the system on a power-button press (the GPD win has a different PMIC).
Move the registering of the power-button press/release interrupt-handler
from axp20x_pek_probe_input_device() to axp20x_pek_probe() so that the
PMIC will wakeup the system on a power-button press, even if we do not
register an input device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20200426155757.297087-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix a use-after-free noticed by running with KASAN enabled. If
rmi_irq_fn() is run twice in a row, then rmi_f11_attention() (among
others) will end up reading from drvdata->attn_data.data, which was
freed and left dangling in rmi_irq_fn().
Commit 55edde9fff ("Input: synaptics-rmi4 - prevent UAF reported by
KASAN") correctly identified and analyzed this bug. However the attempted
fix only NULLed out a local variable, missing the fact that
drvdata->attn_data is a struct, not a pointer.
NULL out the correct pointer in the driver data to prevent the attention
functions from copying from it.
Fixes: 55edde9fff ("Input: synaptics-rmi4 - prevent UAF reported by KASAN")
Fixes: b908d3cd81 ("Input: synaptics-rmi4 - allow to add attention data")
Signed-off-by: Evan Green <evgreen@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200427145537.1.Ic8f898e0147beeee2c005ee7b20f1aebdef1e7eb@changeid
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This reverts commit 1893150646. From Kevin
Locke:
"... nomux only appeared to fix the issue because the controller
continued working after warm reboots. After more thorough testing from
both warm and cold start, I now believe the entry should be added to
i8042_dmi_reset_table rather than i8042_dmi_nomux_table as i8042.reset=1
alone is sufficient to avoid the issue from both states while
i8042.nomux is not."
Allow the firmware to specify the mapping between the scan code and the
linux keycode. This takes the form of a "linux,keymap" property which is
an array of u32 values, each value specifying mapping for a key.
Signed-off-by: Rajat Jain <rajatja@google.com>
Link: https://lore.kernel.org/r/20200427210259.91330-3-rajatja@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Certain keyboards have their top-row keys intended for actions such as
"Browser back", "Browser Refresh", "Fullscreen" etc as their primary mode,
thus they will send scan codes for those actions. Further, they don't
have a dedicated "Fn" key so don't have the capability to generate
function key codes (e.g. F1, F2 etc..). However in this case, if
userspace still wants to "synthesize" those function keys using the top
row action keys, it needs to know the physical position of the top row
keys. (Essentially a mapping between usage codes and a physical location
in the top row).
This patch enhances the atkbd driver to receive such a mapping from the
firmware / device tree, and expose it to userspace in the form of a
function-row-physmap attribute. The attribute would be a space separated
ordered list of physical codes, for the keys in the function row, in
left-to-right order.
The attribute will only be present if the kernel knows about such mapping,
otherwise the attribute shall not be visible.
Signed-off-by: Rajat Jain <rajatja@google.com>
Link: https://lore.kernel.org/r/20200427210259.91330-2-rajatja@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Attach the firmware node to the serio i8042 kbd device so that device
properties can be passed from the firmware.
Signed-off-by: Rajat Jain <rajatja@google.com>
Link: https://lore.kernel.org/r/20200427210259.91330-1-rajatja@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MMS345L is another first generation touch screen from Melfas,
which uses mostly the same registers as MMS152.
However, there is some garbage printed during initialization.
Apparently MMS345L does not have the MMS152_COMPAT_GROUP register
that is read+printed during initialization.
TSP FW Rev: bootloader 0x6 / core 0x26 / config 0x26, Compat group: \x06
On earlier kernel versions the compat group was actually printed as
an ASCII control character, seems like it gets escaped now.
But we probably shouldn't print something from a random register.
Add a separate "melfas,mms345l" compatible that avoids reading
from the MMS152_COMPAT_GROUP register. This might also help in case
there is some other device-specific quirk in the future.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Andi Shyti <andi@etezian.org>
Link: https://lore.kernel.org/r/20200423102431.2715-1-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to the file name and Kconfig, a 'k' is missing in this driver
name. It should be "dlink-dir685-touchkeys".
Fixes: 131b3de701 ("Input: add D-Link DIR-685 touchkeys driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200412213937.5287-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Sending [ 0x05, 0x20, 0x00, 0x0f, 0x06 ] packet for Xbox One S controllers
fixes an issue where controller is stuck in Bluetooth mode and not sending
any inputs.
Signed-off-by: Łukasz Patron <priv.luk@gmail.com>
Reviewed-by: Cameron Gutman <aicommander@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200422075206.18229-1-priv.luk@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_flush_device() should only be called once the struct file is being
released and no open descriptors remain, but evdev_flush() was calling
it whenever a file descriptor was closed.
This caused uploaded force-feedback effects to be erased when a process
did a dup()/close() on the event FD, called system(), etc.
Call input_flush_device() from evdev_release() instead.
Reported-by: Mathieu Maret <mathieu.maret@gmail.com>
Signed-off-by: Brendan Shanks <bshanks@codeweavers.com>
Link: https://lore.kernel.org/r/20200421231003.7935-1-bshanks@codeweavers.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is now an IIO driver for GP2AP002A00F and GP2AP002S00F in
drivers/iio/light/gp2ap002.c.
Delete this driver, it is unused in the kernel tree and new users can make
use of the IIO driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200417203059.8151-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some processes, such as systemd, are only polling for EPOLLERR|EPOLLHUP.
As evdev uses unkeyed wakeups, such a poll receives many spurious
wakeups from uninteresting events.
Use keyed wakeups to allow the wakeup target to more efficiently discard
these uninteresting events.
Signed-off-by: Kenny Levinsen <kl@kl.wtf>
Link: https://lore.kernel.org/r/20200410233557.3892-1-kl@kl.wtf
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Based on available information this uses the singletouch irtouch
protocol. This is tested and confirmed to be fully functional on
the BonXeon TP hardware I have.
Signed-off-by: James Hilliard <james.hilliard1@gmail.com>
Link: https://lore.kernel.org/r/20200413184217.55700-1-james.hilliard1@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch makes use of cros_ec_cmd_xfer_status() instead of
cros_ec_cmd_xfer(). In this case there is no advantage of doing this
apart from that we want to make cros_ec_cmd_xfer() a private function
for the EC protocol and let people only use the
cros_ec_cmd_xfer_status() to return Linux standard error codes.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20200414210434.1534982-1-enric.balletbo@collabora.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MMS345L is another first generation touch screen from Melfas,
which uses the same registers as MMS152.
However, using I2C_M_NOSTART for it causes errors when reading:
i2c i2c-0: sendbytes: NAK bailout.
mms114 0-0048: __mms114_read_reg: i2c transfer failed (-5)
The driver works fine as soon as I2C_M_NOSTART is removed.
Reviewed-by: Andi Shyti <andi@etezian.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200405170904.61512-1-stephan@gerhold.net
[dtor: removed separate mms345l handling, made everyone use standard
transfer mode, propagated the 10bit addressing flag to the read part of the
transfer as well.]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Elan uses the least significant bit of byte 33 to signal the type of
contact (finger versus palm). The default value is 1 for all firmwares,
which is reported as MT_TOOL_FINGER. If firmware supports palm detection,
the bit will change to 0 and the driver will report such contact as
MT_TOOL_PALM.
Signed-off-by: Johnny Chuang <johnny.chuang@emc.com.tw>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Link: https://lore.kernel.org/r/1585551756-29066-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"An update to the Goodix touchscreen driver to enable it work properly
on various Bay Trail and Cherry Trail devices, and a few other
assorted changes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (26 commits)
Input: update SPDX tag for input-event-codes.h
Input: i8042 - add Acer Aspire 5738z to nomux list
Input: goodix - fix compilation when ACPI support is disabled
dt-bindings: touchscreen: Convert edt-ft5x06 to json-schema
Input: of_touchscreen - explicitly choose axis
Input: goodix - support gt9147 touchpanel
dt-bindings: touchscreen: goodix: support of gt9147
Input: goodix - add support for Goodix GT917S
Input: goodix - use string-based chip ID
dt-bindings: input: touchscreen: add compatible string for Goodix GT917S
Input: goodix - add support for more then one touch-key
Input: goodix - fix spurious key release events
Input: goodix - try to reset the controller if the i2c-test fails
Input: goodix - restore config on resume if necessary
Input: goodix - make goodix_send_cfg() take a raw buffer as argument
Input: goodix - add minimum firmware size check
Input: goodix - save a copy of the config from goodix_read_config()
Input: goodix - move defines to above struct goodix_ts_data declaration
Input: goodix - add support for controlling the IRQ pin through ACPI methods
Input: goodix - add support for getting IRQ + reset GPIOs on Bay Trail devices
...
- Add support for IQS620A/621/622/624/625 Azoteq IQS62X Sensors
- New Device Support
- Add support for ADC, IRQ, Regulator, RTC and WDT to Ricoh RN5T618 PMIC
- Add support for Comet Lake to Intel LPSS
- New Functionality
- Add support for Charger Detection to Spreadtrum SC27xx PMICs
- Add support for Interrupt Polarity to Dialog Semi DA9062/61 PMIC
- Add ACPI enumeration support to Diolan DLN2 USB Adaptor
- Fix-ups
- Device Tree; iqs62x, rn5t618, cros_ec_dev, stm32-lptimer, rohm,bd71837, rohm,bd71847
- I2C registration; rn5t618
- Kconfig; MFD_CPCAP, AB8500_CORE, MFD_WM8994, MFD_WM97xx, MFD_STPMIC1
- Use flexible-array members; omap-usb-tll, qcom-pm8xxx
- Remove unnecessary casts; omap-usb-host, omap-usb-tll
- Power (suspend/resume/poweroff) enhancements; rk808
- Improve error/sanity checking; dln2
- Use snprintf(); aat2870-core
- Bug Fixes
- Fix PCI IDs; intel-lpss-pci
-----BEGIN PGP SIGNATURE-----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=hJ2o
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull mfd updates from Lee Jones:
"New Drivers:
- Add support for IQS620A/621/622/624/625 Azoteq IQS62X Sensors
New Device Support:
- Add support for ADC, IRQ, Regulator, RTC and WDT to Ricoh RN5T618 PMIC
- Add support for Comet Lake to Intel LPSS
New Functionality:
- Add support for Charger Detection to Spreadtrum SC27xx PMICs
- Add support for Interrupt Polarity to Dialog Semi DA9062/61 PMIC
- Add ACPI enumeration support to Diolan DLN2 USB Adaptor
Fix-ups:
- Device Tree; iqs62x, rn5t618, cros_ec_dev, stm32-lptimer, rohm,bd71837, rohm,bd71847
- I2C registration; rn5t618
- Kconfig; MFD_CPCAP, AB8500_CORE, MFD_WM8994, MFD_WM97xx, MFD_STPMIC1
- Use flexible-array members; omap-usb-tll, qcom-pm8xxx
- Remove unnecessary casts; omap-usb-host, omap-usb-tll
- Power (suspend/resume/poweroff) enhancements; rk808
- Improve error/sanity checking; dln2
- Use snprintf(); aat2870-core
Bug Fixes:
- Fix PCI IDs in intel-lpss-pci"
* tag 'mfd-next-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (33 commits)
mfd: intel-lpss: Fix Intel Elkhart Lake LPSS I2C input clock
mfd: aat2870: Use scnprintf() for avoiding potential buffer overflow
mfd: dln2: Allow to be enumerated via ACPI
mfd: da9062: Add support for interrupt polarity defined in device tree
dt-bindings: bd718x7: Yamlify and add BD71850
mfd: dln2: Fix sanity checking for endpoints
mfd: intel-lpss: Add Intel Comet Lake PCH-V PCI IDs
mfd: sc27xx: Add USB charger type detection support
dt-bindings: mfd: Document STM32 low power timer bindings
mfd: rk808: Convert RK805 to shutdown/suspend hooks
mfd: rk808: Reduce shutdown duplication
mfd: rk808: Stop using syscore ops
mfd: rk808: Ensure suspend/resume hooks always work
mfd: rk808: Always use poweroff when requested
mfd: omap: Remove useless cast for driver.name
mfd: Kconfig: Fix some misspelling of the word functionality
mfd: pm8xxx: Replace zero-length array with flexible-array member
mfd: omap-usb-tll: Replace zero-length array with flexible-array member
mfd: cpcap: Fix compile if MFD_CORE is not selected
mfd: cros_ec: Check DT node for usbpd-notify add
...
The Acer Aspire 5738z has a button to disable (and re-enable) the
touchpad next to the touchpad.
When this button is pressed a LED underneath indicates that the touchpad
is disabled (and an event is send to userspace and GNOME shows its
touchpad enabled / disable OSD thingie).
So far so good, but after re-enabling the touchpad it no longer works.
The laptop does not have an external ps2 port, so mux mode is not needed
and disabling mux mode fixes the touchpad no longer working after toggling
it off and back on again, so lets add this laptop model to the nomux list.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200331123947.318908-1-hdegoede@redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
acpi_evaluate_object() and acpi_execute_simple_method() are not part of
the group of ACPI related functions which get stubbed by
include/linux/acpi.h when ACPI support is disabled, so the
IRQ_PIN_ACCESS_ACPI_METHOD handling code must be stubbed out.
For consistency use the same #if condition as which is used to replace
goodix_add_acpi_gpio_mappings with a stub.
Fixes: c5fca48532 ("Input: goodix - add support for controlling the IRQ pin through ACPI methods")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200401014529.GL75430@dtor-ws
[dtor: stubbed out the ACPI method accessors]
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here is the "big" set of driver core changes for 5.7-rc1.
Nothing huge in here, just lots of little firmware core changes and use
of new apis, a libfs fix, a debugfs api change, and some driver core
deferred probe rework.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXoHLIg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yle2ACgjJJzRJl9Ckae3ms+9CS4OSFFZPsAoKSrXmFc
Z7goYQdZo1zz8c0RYDrJ
=Y91m
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the "big" set of driver core changes for 5.7-rc1.
Nothing huge in here, just lots of little firmware core changes and
use of new apis, a libfs fix, a debugfs api change, and some driver
core deferred probe rework.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (44 commits)
Revert "driver core: Set fw_devlink to "permissive" behavior by default"
driver core: Set fw_devlink to "permissive" behavior by default
driver core: Replace open-coded list_last_entry()
driver core: Read atomic counter once in driver_probe_done()
libfs: fix infoleak in simple_attr_read()
driver core: Add device links from fwnode only for the primary device
platform/x86: touchscreen_dmi: Add info for the Chuwi Vi8 Plus tablet
platform/x86: touchscreen_dmi: Add EFI embedded firmware info support
Input: icn8505 - Switch to firmware_request_platform for retreiving the fw
Input: silead - Switch to firmware_request_platform for retreiving the fw
selftests: firmware: Add firmware_request_platform tests
test_firmware: add support for firmware_request_platform
firmware: Add new platform fallback mechanism and firmware_request_platform()
Revert "drivers: base: power: wakeup.c: Use built-in RCU list checking"
drivers: base: power: wakeup.c: Use built-in RCU list checking
component: allow missing unbind callback
debugfs: remove return value of debugfs_create_file_size()
debugfs: Check module state before warning in {full/open}_proxy_open()
firmware: fix a double abort case with fw_load_sysfs_fallback
arch_topology: Fix putting invalid cpu clk
...
This patch adds key and switch support for the Azoteq IQS620A,
IQS621, IQS622, IQS624 and IQS625 multi-function sensors.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull input fixes from Dmitry Torokhov:
- a fix to generate proper timestamps on key autorepeat events that
were broken recently
- a fix for Synaptics driver to only activate reduced reporting mode
when explicitly requested
- a new keycode for "selective screenshot" function
- other assorted fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: fix stale timestamp on key autorepeat events
Input: move the new KEY_SELECTIVE_SCREENSHOT keycode
Input: avoid BIT() macro usage in the serio.h UAPI header
Input: synaptics-rmi4 - set reduced reporting mode only when requested
Input: synaptics - enable RMI on HP Envy 13-ad105ng
Input: allocate keycode for "Selective Screenshot" key
Input: tm2-touchkey - add support for Coreriver TC360 variant
dt-bindings: input: add Coreriver TC360 binding
dt-bindings: vendor-prefixes: Add Coreriver vendor prefix
Input: raydium_i2c_ts - fix error codes in raydium_i2c_boot_trigger()
We need to refresh timestamp when emitting key autorepeat events, otherwise
they will carry timestamp of the original key press event.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=206929
Fixes: 3b51c44bd6 ("Input: allow drivers specify timestamp for input events")
Cc: stable@vger.kernel.org
Reported-by: teika kazura <teika@gmx.com>
Tested-by: teika kazura <teika@gmx.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The previous patch "c5ccf2ad3d33 (Input: synaptics-rmi4 - switch to
reduced reporting mode)" enabled reduced reporting mode unintentionally
on some devices, if the firmware was configured with default Delta X/Y
threshold values. The result unintentionally degrade the performance of
some touchpads.
This patch checks to see that the driver is modifying the delta X/Y
thresholds before modifying the reporting mode.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Fixes: c5ccf2ad3d ("Input: synaptics-rmi4 - switch to reduced reporting mode")
Link: https://lore.kernel.org/r/20200312005549.29922-1-aduggan@synaptics.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This laptop (and perhaps other variants of the same model) reports an
SMBus-capable Synaptics touchpad. Everything (including suspend and
resume) works fine when RMI is enabled via the kernel command line, so
let's add it to the whitelist.
Signed-off-by: Yussuf Khalil <dev@pp3345.net>
Link: https://lore.kernel.org/r/20200307213508.267187-1-dev@pp3345.net
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The 'axis + 1' calculation is implicit and potentially error prone.
Moreover, few lines before the axis is set explicitly for both X and Y.
Do the same when retrieving different properties for X and Y.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200303180917.12563-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for it by adding compatible and supported chip data
(default settings used).
The chip data on GT9147 is similar to GT912, like
- config data register has 0x8047 address
- config data register max len is 240
- config data checksum has 8-bit
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/1583144308-3781-3-git-send-email-yannick.fertre@st.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Goodix GT917S is a touchscreen chip from Goodix that is in the GT1x
family.
Add its support by assigning the gt1x config to it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200228010146.12215-4-icenowy@aosc.io
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For Goodix GT917S chip, the chip ID string is "917S", which contains not
only numbers now.
Use string-based chip ID in the driver to support this chip and further
chips with alphanumber ID.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200228010146.12215-3-icenowy@aosc.io
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some devices with a goodix touchscreen have more then 1 capacitive
touch-key. This commit replaces the current support for a single
touch-key, which ignored the reported key-code. With support for
up to 7 touch-keys, based upon checking the key-code which is
post-fixed to any reported touch-data.
KEY_LEFTMETA is assigned to the first touch-key (it will still be
the default keycode for devices with a single touch-key).
KEY_F1, KEY_F2... are assigned as default keycode for the other
touch-keys.
This commit also add supports for keycode remapping, so that
systemd-udev's hwdb can be used to remap the codes to send
keycodes to match the icons on the buttons for devices with more
then 1 touch-key.
Signed-off-by: Dmitry Mastykin <dmastykin@astralinux.ru>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200316075302.3759-1-dmastykin@astralinux.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The goodix panel sends spurious interrupts after a 'finger up' event,
which always cause a timeout.
We were exiting the interrupt handler by reporting touch_num == 0, but
this was still processed as valid and caused the code to use the
uninitialised point_data, creating spurious key release events.
Report an error from the interrupt handler so as to avoid processing
invalid point_data further.
Signed-off-by: Dmitry Mastykin <dmastykin@astralinux.ru>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200316075302.3759-2-dmastykin@astralinux.ru
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On some ACPI/x86 devices (where we use one of the ACPI IRQ pin access
methods) the firmware is buggy, it does not properly reset the controller
at boot, and we cannot communicate with it.
Normally on ACPI/x86 devices we do not want to reset the controller at
probe time since in some cases this causes the controller to loose its
configuration and this is loaded into it by the system's firmware.
So on these systems we leave the reset_controller_at_probe flag unset,
even though we have a access to both the IRQ and reset pins and thus
could reset it.
In the case of the buggy firmware we have to reset the controller to
actually be able to talk to it.
This commit adds a special case for this, if the goodix_i2c_test() fails,
and we have not reset the controller yet; and we do have a way to reset
the controller then retry the i2c-test after resetting the controller.
This fixes the driver failing at probe on ACPI/x86 systems with this
firmware bug.
Reported-and-tested-by: Dmitry Mastykin <dmastykin@astralinux.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200311191013.10826-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Our goodix_check_cfg_* helpers do things like:
int i, raw_cfg_len = cfg->size - 2;
...
if (check_sum != cfg->data[raw_cfg_len]) {
When cfg->size < 2, this will end up indexing the cfg->data array with
a negative value, which will not end well.
To fix this this commit adds a new GOODIX_CONFIG_MIN_LENGTH define and
adds a minimum size check for firmware-config files using this new define.
For consistency this commit also adds a new GOODIX_CONFIG_GT9X_LENGTH for
the length used for recent gt9xx and gt1xxx chips, instead of using
GOODIX_CONFIG_MAX_LENGTH for this, so that if other length defines get
added in the future it will be clear that the MIN and MAX defines should
contain the min and max values of all the other defines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200307121505.3707-9-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On most Bay Trail (x86, UEFI + ACPI) devices the ACPI tables do not have
a _DSD with a "daffd814-6eba-4d8c-8a91-bc9bbf4aa301" UUID, adding
"irq-gpios" and "reset-gpios" mappings, so we cannot get the GPIOS by name
without first manually adding mappings ourselves.
These devices contain 2 GpioIo resource in their _CRS table, on all 4 such
devices which I have access to, the order of the 2 GPIOs is reset, int.
Note that the GPIO to which the touchscreen controller irq pin is connected
is configured in direct-irq mode on these Bay Trail devices, the
pinctrl-baytrail.c driver still allows controlling the pin as a GPIO in
this case, but this is not necessarily the case on other X86 ACPI
platforms, nor do we have a guarantee that the GPIO order is the same
elsewhere, so we limit the use of a _CRS table with 2 GpioIo resources
to Bay Trail devices only.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-5-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On most Cherry Trail (x86, UEFI + ACPI) devices the ACPI tables do not have
a _DSD with a "daffd814-6eba-4d8c-8a91-bc9bbf4aa301" UUID, adding
"irq-gpios" and "reset-gpios" mappings, so we cannot get the GPIOS by name
without first manually adding mappings ourselves.
These devices contain 1 GpioInt and 1 GpioIo resource in their _CRS table:
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (RBUF, ResourceTemplate ()
{
I2cSerialBusV2 (0x0014, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\_SB.PCI0.I2C2",
0x00, ResourceConsumer, , Exclusive,
)
GpioInt (Edge, ActiveLow, Shared, PullDefault, 0x0000,
"\\_SB.GPO1", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0013
}
GpioIo (Shared, PullDefault, 0x0000, 0x0000,
IoRestrictionOutputOnly,
"\\_SB.GPO1", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x0019
}
})
Return (RBUF) /* \_SB_.PCI0.I2C2.TCS1._CRS.RBUF */
}
There is no fixed order for these 2. This commit adds code to check that
there is 1 of each as expected and then registers a mapping matching their
order using devm_acpi_dev_add_driver_gpios().
This gives us access to both GPIOs allowing us to properly suspend the
controller during suspend, and making it possible to reset the controller
if necessary.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200307121505.3707-4-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Before this commit we would always reset the controller at probe when we
have access to the GPIOs which are necessary to do a reset.
Doing the reset requires access to the GPIOs, but just because we have
access to the GPIOs does not mean that we should always reset the
controller at probe. On X86 ACPI platforms the BIOS / UEFI firmware will
already have reset the controller and it will have loaded the device
specific config into the controller. Doing the reset sometimes causes the
controller to lose its configuration, so on X86 ACPI platforms this is not
a good idea.
This commit adds a new reset_controller_at_probe boolean to control the
reset at probe behavior.
This commits sets the new bool to true when we set irq_pin_access_method
to IRQ_PIN_ACCESS_GPIO, so there are no functional changes.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
At least on X86 ACPI platforms it is not necessary to load the touchscreen
controller config from disk, if it needs to be loaded this has already been
done by the BIOS / UEFI firmware.
Even on other (e.g. devicetree) platforms the config-loading as currently
done has the issue that the loaded cfg file is based on the controller
model, but the actual cfg is device specific, so the cfg files are not
part of linux-firmware and this can only work with a device specific OS
image which includes the cfg file.
And we do not need access to the GPIOs at all to load the config, if we
do not have access we can still load the config.
So all in all tying the decision to try to load the config from disk to
being able to access the GPIOs is not desirable. This commit adds a new
load_cfg_from_disk boolean to control the firmware loading instead.
This commits sets the new bool to true when we set irq_pin_access_method
to IRQ_PIN_ACCESS_GPIO, so there are no functional changes.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200307121505.3707-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.
So far we have only effectively supported this on devices which use
devicetree. On X86 ACPI platforms both looking up the pins; and using a
pin as both IRQ and GPIO is a bit more complicated. E.g. on some devices
we cannot directly access the IRQ pin as GPIO and we need to call ACPI
methods to control it instead.
This commit adds a new irq_pin_access_method field to the goodix_chip_data
struct and adds goodix_irq_direction_output and goodix_irq_direction_input
helpers which together abstract the GPIO accesses to the IRQ pin.
This is a preparation patch for adding support for properly suspending the
touchscreen on X86 ACPI platforms.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1786317
BugLink: https://github.com/nexus511/gpd-ubuntu-packages/issues/10
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=199207
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20200307121505.3707-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Unfortunately sofar we have been unable to get permission to redistribute
icn8505 touchscreen firmwares in linux-firmware. This means that people
need to find and install the firmware themselves before the touchscreen
will work
Some UEFI/x86 tablets with an icn8505 touchscreen have a copy of the fw
embedded in their UEFI boot-services code.
This commit makes the icn8505 driver use the new firmware_request_platform
function, which will fallback to looking for such an embedded copy when
direct filesystem lookup fails. This will make the touchscreen work OOTB
on devices where there is a fw copy embedded in the UEFI code.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200115163554.101315-9-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unfortunately sofar we have been unable to get permission to redistribute
Silead touchscreen firmwares in linux-firmware. This means that people
need to find and install the firmware themselves before the touchscreen
will work
Some UEFI/x86 tablets with a Silead touchscreen have a copy of the fw
embedded in their UEFI boot-services code.
This commit makes the silead driver use the new firmware_request_platform
function, which will fallback to looking for such an embedded copy when
direct filesystem lookup fails. This will make the touchscreen work OOTB
on devices where there is a fw copy embedded in the UEFI code.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200115163554.101315-8-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Coreriver TouchCore 360 is like the midas board touchkey, but it is
using a fixed regulator.
Signed-off-by: Nick Reitemeyer <nick.reitemeyer@web.de>
Link: https://lore.kernel.org/r/20200121141525.3404-3-nick.reitemeyer@web.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These functions are supposed to return negative error codes but instead
it returns true on failure and false on success. The error codes are
eventually propagated back to user space.
Fixes: 48a2b78348 ("Input: add Raydium I2C touchscreen driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200303101306.4potflz7na2nn3od@kili.mountain
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch supports reporting resolution for ABS_MT_TOUCH_MAJOR event.
This information is needed in showing pressure/width radius.
Signed-off-by: Johnny Chuang <johnny.chuang@emc.com.tw>
Reviewed-by: Harry Cutts <hcutts@chromium.org>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/1582766000-23023-1-git-send-email-johnny.chuang.emc@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchscreen on the Cube I15-TC don't match the default display,
with 0,0 touches being reported when touching at the top-right of
the screen.
Add a quirk to invert the x coordinate.
Reported-and-tested-by: Arkadiy <arkan49@yandex.ru>
Signed-off-by: Sergei A. Trusov <sergei.a.trusov@ya.ru>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- a few drivers have been updated to use flexible-array syntax instead
of GCC extension
- ili210x touchscreen driver now supports the 2120 protocol flavor
- a couple more of Synaptics devices have been switched over to RMI4
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cyapa - replace zero-length array with flexible-array member
Input: tca6416-keypad - replace zero-length array with flexible-array member
Input: gpio_keys_polled - replace zero-length array with flexible-array member
Input: synaptics - remove the LEN0049 dmi id from topbuttonpad list
Input: synaptics - enable SMBus on ThinkPad L470
Input: synaptics - switch T470s to RMI4 by default
Input: gpio_keys - replace zero-length array with flexible-array member
Input: goldfish_events - replace zero-length array with flexible-array member
Input: psmouse - switch to using i2c_new_scanned_device()
Input: ili210x - add ili2120 support
Input: ili210x - fix return value of is_visible function
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200214172132.GA28389@embeddedor
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200214172022.GA27490@embeddedor
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200214171907.GA26588@embeddedor
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Yoga 11e is using LEN0049, but it doesn't have a trackstick.
Thus, there is no need to create a software top buttons row.
However, it seems that the device works under SMBus, so keep it as part
of the smbus_pnp_ids.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200115013023.9710-1-benjamin.tissoires@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200213002600.GA31916@embeddedor.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200213002430.GA31056@embeddedor.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Move from the deprecated i2c_new_probed_device() to the new
i2c_new_scanned_device(). Make use of the new ERRPTR if suitable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20200210165902.5250-1-wsa+renesas@sang-engineering.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds support for the Ilitek ili2120 touchscreen found in the
Fairphone 2 smartphone.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20200209151904.661210-1-luca@z3ntu.xyz
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The is_visible function expects the permissions associated with an
attribute of the sysfs group or 0 if an attribute is not visible.
Change the code to return the attribute permissions when the attribute
should be visible which resolves the warning:
Attribute calibrate: Invalid permissions 01
Fixes: cc12ba1872 ("Input: ili210x - optionally show calibrate sysfs attribute")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Sven Van Asbroeck <TheSven73@gmail.com>
Link: https://lore.kernel.org/r/20200209145628.649409-1-luca@z3ntu.xyz
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Merge more updates from Andrew Morton:
"The rest of MM and the rest of everything else: hotfixes, ipc, misc,
procfs, lib, cleanups, arm"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (67 commits)
ARM: dma-api: fix max_pfn off-by-one error in __dma_supported()
treewide: remove redundant IS_ERR() before error code check
include/linux/cpumask.h: don't calculate length of the input string
lib: new testcases for bitmap_parse{_user}
lib: rework bitmap_parse()
lib: make bitmap_parse_user a wrapper on bitmap_parse
lib: add test for bitmap_parse()
bitops: more BITS_TO_* macros
lib/string: add strnchrnul()
proc: convert everything to "struct proc_ops"
proc: decouple proc from VFS with "struct proc_ops"
asm-generic/tlb: provide MMU_GATHER_TABLE_FREE
asm-generic/tlb: rename HAVE_MMU_GATHER_NO_GATHER
asm-generic/tlb: rename HAVE_MMU_GATHER_PAGE_SIZE
asm-generic/tlb: rename HAVE_RCU_TABLE_FREE
asm-generic/tlb: add missing CONFIG symbol
asm-gemeric/tlb: remove stray function declarations
asm-generic/tlb: avoid potential double flush
mm/mmu_gather: invalidate TLB correctly on batch allocation failure and flush
powerpc/mmu_gather: enable RCU_TABLE_FREE even for !SMP case
...
support by Dexuan Cui.
- Fix for a warning shown when host sends non-aligned balloon requests
by Tianyu Lan.
-----BEGIN PGP SIGNATURE-----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=3tZ1
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull Hyper-V updates from Sasha Levin:
- Most of the commits here are work to enable host-initiated
hibernation support by Dexuan Cui.
- Fix for a warning shown when host sends non-aligned balloon requests
by Tianyu Lan.
* tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
hv_utils: Add the support of hibernation
hv_utils: Support host-initiated hibernation request
hv_utils: Support host-initiated restart request
Tools: hv: Reopen the devices if read() or write() returns errors
video: hyperv: hyperv_fb: Use physical memory for fb on HyperV Gen 1 VMs.
Drivers: hv: vmbus: Ignore CHANNELMSG_TL_CONNECT_RESULT(23)
video: hyperv_fb: Fix hibernation for the deferred IO feature
Input: hyperv-keyboard: Add the support of hibernation
hv_balloon: Balloon up according to request page number
When the distance thresholds are set the controller must be in reduced
reporting mode for them to have any effect on the interrupt generation.
This has a potentially large impact on the number of events the host
needs to process.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Link: https://lore.kernel.org/r/20200120111628.18376-1-l.stach@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
Add suspend() and resume() functions so the Hyper-V virtual keyboard
can participate in VM hibernation.
Note that the keyboard is a "wakeup" device that could abort an in-progress
hibernation if there is keyboard event. No attempt is made to suppress this
behavior. If desired, a sysadmin can disable the keyboard as a wakeup device
using standard mechanisms such as:
echo disabled > /sys/bus/vmbus/drivers/hyperv_keyboard/XXX/power/wakeup
(where XXX is the device's GUID)
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch adds a platform driver for supporting keyboard and mouse
interface of SGI IOC3 chips.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Link: https://lore.kernel.org/r/20200122135220.22354-1-tbogendoerfer@suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are many devices, including several mobile battery-powered
devices, using other AXP variants as their PMIC. Allow them to use
the power key as a wakeup source.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20200115051253.32603-3-samuel@sholland.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Unlike most other power button drivers, this driver unconditionally
enables its wakeup IRQ. It should be using device_may_wakeup() to
respect the userspace configuration of wakeup sources.
Because the AXP20x MFD device uses regmap-irq, the AXP20x PEK IRQs are
nested off of regmap-irq's threaded interrupt handler. The device core
ignores such interrupts, so to actually disable wakeup, we must
explicitly disable all non-wakeup interrupts during suspend.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200115051253.32603-2-samuel@sholland.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20191210141103.15910-1-alexandru.ardelean@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Setting the vibrator enable_mask is not implemented correctly:
For regmap_update_bits(map, reg, mask, val) we give in either
regs->enable_mask or 0 (= no-op) as mask and "val" as value.
But "val" actually refers to the vibrator voltage control register,
which has nothing to do with the enable_mask.
So we usually end up doing nothing when we really wanted
to enable the vibrator.
We want to set or clear the enable_mask (to enable/disable the vibrator).
Therefore, change the call to always modify the enable_mask
and set the bits only if we want to enable the vibrator.
Fixes: d4c7c5c96c ("Input: pm8xxx-vib - handle separate enable register")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200114183442.45720-1-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver was issuing synchronous uninterruptible control requests
without using a timeout. This could lead to the driver hanging on probe
due to a malfunctioning (or malicious) device until the device is
physically disconnected. While sleeping in probe the driver prevents
other devices connected to the same hub from being added to (or removed
from) the bus.
The USB upper limit of five seconds per request should be more than
enough.
Fixes: 99f83c9c9a ("[PATCH] USB: add driver for Keyspan Digital Remote")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org> # 2.6.13
Link: https://lore.kernel.org/r/20200113171715.30621-1-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We need the of_match table if we want to use the compatible string in
the pmic's child node and get the onkey driver loaded automatically.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The F54 Report Data is apparently read through a fifo and for
the smbus protocol that means that between reading a block of 32
bytes the rmiaddr shouldn't be incremented. However, changing
that causes other non-fifo reads to fail and so that change was
reverted.
This patch changes just the F54 function and it now reads 32 bytes
at a time from the fifo, using the F54_FIFO_OFFSET to update the
start address that is used when reading from the fifo.
This has only been tested with smbus, not with i2c or spi. But I
suspect that the same is needed there since I think similar
problems will occur there when reading more than 256 bytes.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Timo Kaufmann <timokau@zoho.com>
Link: https://lore.kernel.org/r/20200115124819.3191024-3-hverkuil-cisco@xs4all.nl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This reverts commit a284e11c37.
This causes problems (drifting cursor) with at least the F11 function that
reads more than 32 bytes.
The real issue is in the F54 driver, and so this should be fixed there, and
not in rmi_smbus.c.
So first revert this bad commit, then fix the real problem in F54 in another
patch.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Timo Kaufmann <timokau@zoho.com>
Fixes: a284e11c37 ("Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200115124819.3191024-2-hverkuil-cisco@xs4all.nl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl4SYegeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG4m4H+QGCUN8SXN+2B+0/
BfzOf7PFoKzAx3NwDbJQIZqhSl+Zfa4n3VGPEF8sXsvoQgdYvuJnS/5JiAZ9iRIH
HAfFzegzQ3mCl8Du+SqCvQKs2Jt4OMCX62KGRebRBhpoKfZdwmN7n7pn9lWO771K
9rxTpeItXhmK46jOFRbi5oyQfmkfSfyUN1b9CB53FXFS+ZDkDNA7QQiIYnKOD7SZ
RrL7czhZ580QOC61qOlnz1GIhRzvU5SXg4OtuI3YfoOJRY5FKC3YtOgLReT0vPs+
vEhAyP93upVXIhqm10WHNjd4t4a45Vy5ff64uFsQ9QV4nnqsC2C70YwWbVDdtz/W
Lm0mvE8=
=NECs
-----END PGP SIGNATURE-----
Merge tag 'v5.5-rc5' into next
Sync up with mainline to get SPI "delay" API changes.
We do not have to handle the wake-irq within the driver because the pm
core can handle this for us. The only use case for the suspend/resume
callbacks was to handle the wake-irq so we can remove the callbacks.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since day one the touch controller acts as wakeup-source. This seems to
be wrong since the device supports deep-sleep mechanism [1] which
requires a reset to leave it. Also some designs won't use the
touchscreen as wakeup-source.
According discussion [2] we decided to break backward compatibility and
go the common way by using the 'wakeup-source' device-property.
[1] https://www.newhavendisplay.com/appnotes/datasheets/touchpanel/FT5x26.pdf
[2] https://patchwork.kernel.org/patch/11149037/
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It seems that the include order is historical increased and no one takes
care of it. Fix this to align it with the common rule to be in a
alphabetical order.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The EP0700MLP1 returns bogus data on the first register read access
(reading the threshold parameter from register 0x00):
edt_ft5x06 2-0038: crc error: 0xfc expected, got 0x40
It ignores writes until then. This patch adds a dummy read after which
the number of sensors and parameter read/writes work correctly.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: bdb5c57f20 ("Input: add sur40 driver for Samsung SUR40 (aka MS Surface 2.0/Pixelsense)")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-8-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Drop the second, redundant reinitialisation of the endpoint-descriptor
pointer from probe.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-7-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure to use the current altsetting when printing size of any extra
descriptors of the interface.
Also fix the s/endpoint/interface/ mixup in the message itself.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-6-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver was checking the number of endpoints of the first alternate
setting instead of the current one, something which could lead to the
driver binding to an invalid interface.
This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 162f98dea4 ("Input: gtco - fix crash on detecting device without endpoints")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-5-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make sure to always use the descriptors of the current alternate setting
to avoid future issues when accessing fields that may differ between
settings.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-4-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver was checking the number of endpoints of the first alternate
setting instead of the current one, something which could lead to the
driver binding to an invalid interface.
This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 8e20cf2bce ("Input: aiptek - fix crash on detecting device without endpoints")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-3-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver was checking the number of endpoints of the first alternate
setting instead of the current one, something which could be used by a
malicious device (or USB descriptor fuzzer) to trigger a NULL-pointer
dereference.
Fixes: 1afca2b66a ("Input: add Pegasus Notetaker tablet driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Martin Kepplinger <martink@posteo.de>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-2-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver misses a check for devm_thermal_zone_of_sensor_register().
Add a check to fix it.
Fixes: e28d0c9cd3 ("input: convert sun4i-ts to use devm_thermal_zone_of_sensor_register")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We observed a large(order-3) allocation in evdev_open() and it may
cause an OOM kernel panic in kzalloc(), before we getting to the
vzalloc() fallback.
Fix it by converting kzalloc()/vzalloc() to kvzalloc() to avoid the
OOM killer logic as we have a vmalloc fallback.
InputReader invoked oom-killer: gfp_mask=0x240c2c0
(GFP_KERNEL|__GFP_NOWARN|__GFP_COMP|__GFP_ZERO), nodemask=0, order=3,
oom_score_adj=-900
...
(dump_backtrace) from (show_stack+0x18/0x1c)
(show_stack) from (dump_stack+0x94/0xa8)
(dump_stack) from (dump_header+0x7c/0xe4)
(dump_header) from (out_of_memory+0x334/0x348)
(out_of_memory) from (__alloc_pages_nodemask+0xe9c/0xeb8)
(__alloc_pages_nodemask) from (kmalloc_order_trace+0x34/0x128)
(kmalloc_order_trace) from (__kmalloc+0x258/0x36c)
(__kmalloc) from (evdev_open+0x5c/0x17c)
(evdev_open) from (chrdev_open+0x100/0x204)
(chrdev_open) from (do_dentry_open+0x21c/0x354)
(do_dentry_open) from (vfs_open+0x58/0x84)
(vfs_open) from (path_openat+0x640/0xc98)
(path_openat) from (do_filp_open+0x78/0x11c)
(do_filp_open) from (do_sys_open+0x130/0x244)
(do_sys_open) from (SyS_openat+0x14/0x18)
(SyS_openat) from (__sys_trace_return+0x0/0x10)
...
Normal: 12488*4kB (UMEH) 6984*8kB (UMEH) 2101*16kB (UMEH) 0*32kB
0*64kB 0*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB = 139440kB
HighMem: 206*4kB (H) 131*8kB (H) 42*16kB (H) 2*32kB (H) 0*64kB
0*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB = 2608kB
...
Kernel panic - not syncing: Out of memory and no killable processes...
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"Just a few small fixups here"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: imx_sc_key - only take the valid data from SCU firmware as key state
Input: add safety guards to input_set_keycode()
Input: input_event - fix struct padding on sparc64
Input: uinput - always report EPOLLOUT
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The two device attrbitues are not declared outside this file
so make them static to avoid the following warnings:
drivers/input/misc/axp20x-pek.c:194:1: warning: symbol 'dev_attr_startup' was not declared. Should it be static?
drivers/input/misc/axp20x-pek.c:195:1: warning: symbol 'dev_attr_shutdown' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20191217152541.2167080-1-ben.dooks@codethink.co.uk
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When reading key state from SCU, the response data from SCU firmware
is 4 bytes due to MU message protocol, but ONLY the first byte is the
key state, other 3 bytes could be some dirty data, so we should ONLY
take the first byte as key state to avoid reporting incorrect state.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Fixes: 688f1dfb69 ("Input: keyboard - imx_sc: Add i.MX system controller key support")
Link: https://lore.kernel.org/r/1576202909-1661-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Going through all uses of timeval, I noticed that we screwed up
input_event in the previous attempts to fix it:
The time fields now match between kernel and user space, but all following
fields are in the wrong place.
Add the required padding that is implied by the glibc timeval definition
to fix the layout, and use a struct initializer to avoid leaking kernel
stack data.
Fixes: 141e5dcaa7 ("Input: input_event - fix the CONFIG_SPARC64 mixup")
Fixes: 2e746942eb ("Input: input_event - provide override for sparc64")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20191213204936.3643476-2-arnd@arndb.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
uinput device is always available for writing so we should always report
EPOLLOUT and EPOLLWRNORM bits, not only when there is nothing to read from
the device.
Fixes: d4b675e1b5 ("Input: uinput - fix returning EPOLLOUT from uinput_poll")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/20191209202254.GA107567@dtor-ws
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To avoid flashing incompatible firmware onto a device we should check
whether "Remark ID" in firmware matches with the one in the controller.
This function is supported by Elan's latest version of boot code, so the
driver decides whether to perform the check based on the boot code version.
Signed-off-by: Johnny Chuang <johnny.chuang@emc.com.tw>
Link: https://lore.kernel.org/r/00a901d5af3c$193e9cd0$4bbbd670$@emc.com.tw
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>