Commit Graph

42 Commits

Author SHA1 Message Date
Vladislav Zolotarov 72fd071833 bnx2x: Parity errors handling for 57710 and 57711
This patch introduces the parity errors handling code for 57710 and 57711 chips.

HW is configured to stop all DMA transactions to the host and sending packets to the network
once parity error is detected, which is meant to prevent silent data corruption.
At the same time HW generates the attention interrupt to every function of the device where parity
has been detected so that driver can start the recovery flow.

The recovery is actually resetting the chip and restarting the driver on all active functions
of the chip where the parity error has been reported.

Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-04-19 13:17:05 -07:00
Linus Torvalds 4ef58d4e2a Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (42 commits)
  tree-wide: fix misspelling of "definition" in comments
  reiserfs: fix misspelling of "journaled"
  doc: Fix a typo in slub.txt.
  inotify: remove superfluous return code check
  hdlc: spelling fix in find_pvc() comment
  doc: fix regulator docs cut-and-pasteism
  mtd: Fix comment in Kconfig
  doc: Fix IRQ chip docs
  tree-wide: fix assorted typos all over the place
  drivers/ata/libata-sff.c: comment spelling fixes
  fix typos/grammos in Documentation/edac.txt
  sysctl: add missing comments
  fs/debugfs/inode.c: fix comment typos
  sgivwfb: Make use of ARRAY_SIZE.
  sky2: fix sky2_link_down copy/paste comment error
  tree-wide: fix typos "couter" -> "counter"
  tree-wide: fix typos "offest" -> "offset"
  fix kerneldoc for set_irq_msi()
  spidev: fix double "of of" in comment
  comment typo fix: sybsystem -> subsystem
  ...
2009-12-09 19:43:33 -08:00
André Goddard Rosa af901ca181 tree-wide: fix assorted typos all over the place
That is "success", "unknown", "through", "performance", "[re|un]mapping"
, "access", "default", "reasonable", "[con]currently", "temperature"
, "channel", "[un]used", "application", "example","hierarchy", "therefore"
, "[over|under]flow", "contiguous", "threshold", "enough" and others.

Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-12-04 15:39:55 +01:00
Yaniv Rosner 46d15cc7a0 bnx2x: Fix 10G mode in BCM8481/BCM84823
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-05 20:00:48 -08:00
Yaniv Rosner 15ddd2d0ef bnx2x: Enable FC when parallel-detect is used
When parallel detect is used, flow-control is set to the
req_fc_auto_adv instead of none.

Motive: when 577xx is FC configuration is set to AUTO, while LP speed
is set to FORCE mode and FC to force RX/TX, link would come up using
parallel detect, and the FC will be set to NONE since FC capabilities
were not negotiated, although the LP is setting FC to force RX/TX.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-05 20:00:35 -08:00
Yaniv Rosner 7846e471b5 bnx2x: Fix CL73 autoneg issues
- Advertise 1G KX4 in CL73 when 1G speed capability is enabled
- Add flow-control negotiation over CL73
- External loopback test on Serdes should be done in FORCE mode, since in
CL73 it is unable to link up with the same core using AUTONEG
- Fix bnx2x_set_led function to support CL73 link leds

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-05 20:00:29 -08:00
Anand Gadiyar 411c940385 trivial: fix typo "for for" in multiple files
trivial: fix typo "for for" in multiple files

Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-09-21 15:14:54 +02:00
Eilon Greenstein ab6ad5a487 bnx2x: Whitespaces and comments
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-12 23:03:01 -07:00
Eilon Greenstein 9c63de6293 bnx2x: Removing unused definitions
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-12 23:03:00 -07:00
Eilon Greenstein 573f203574 bnx2x: Re-factor the initialization code
Moving the code to a more logical place and beautifying it. No real change in
behavior.

Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-12 23:02:59 -07:00
Eilon Greenstein 239d686d49 bnx2x: Adding XAUI CL73 autoneg support
Adding CL73 support to the built in PHY in the 5771x device. Also supporting
fallbacks to CL73 if the link partner does not respond.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-12 23:02:27 -07:00
Eilon Greenstein 2f9044603c bnx2x: BCM8481 LED4 instead of LASI
The BCM8481 does not generate LASI interrupt for 10M, 100M and 1G link, so we
are using LED4 output as the interrupt input to the 57711. This requires some
adaptation in the link interrupt routines

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-12 23:02:18 -07:00
Eilon Greenstein ca00392cb8 bnx2x: Using the new FW
The new FW improves the packets per second rate. It required a lot of change in
the FW which implies many changes in the driver to support it. It is now also
possible for the driver to use a separate MSI-X vector for Rx and Tx - this also
add some to the complicity of this change.

All things said - after this patch, practically all performance matrixes show
improvement.
Though Vladislav Zolotarov is not signed on this patch, he did most of the job
and deserves credit for that.

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-08-12 22:53:28 -07:00
Eilon Greenstein 581ce43d26 bnx2x: Receive traffic that maches management filtering rules
Due to lack of configuration, if the BMC configures the chip to pass all
broadcast/multicast traffic to it, the host will not receive it. On top of
fixing it, also make sure that in promiscuous mode, the host will receive the
management traffic as well.

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-30 12:19:20 -07:00
Eilon Greenstein 4d295db0ef bnx2x: Supporting BCM8727 PHY
Adding support for BCM8727 - a dual port SFP+ PHY. That includes verification of
the optic module vendor and part number - the list of approved modules resides
on the nvram and the module is verified by the FW. Since not all users would
like to use this verification feature, it can be disabled. The default behavior
is to issue a warning if the module is not approved, but still allow using it -
but it is also possible to disable the link if the module is not approved.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-21 11:18:30 -07:00
Eilon Greenstein 279abdf59c bnx2x: Stop management traffic in loopback test
Since management traffic cannot go on the wire while configured to loopback,
simply stop it to avoid race condition when the MAC is set to loopback in the
middle of a packet

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-21 11:18:26 -07:00
Eilon Greenstein cc1cb004df bnx2x: Supporting new BCM8726 FW
Microcode download requires write of another register and read from
"Limiting/LRM mode" register before setting

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 22:32:43 -08:00
Eilon Greenstein 0d1a8d2d7d bnx2x: Misleading name
As noted by Ben Hutchings <bhutchings@solarflare.com>, these are the
capabilities offsets and not the ID itself

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-02 22:32:37 -08:00
Eilon Greenstein 052a38e096 bnx2x: Using registers name
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15 23:31:42 -08:00
Eilon Greenstein c2c8b03e20 bnx2x: Pre emphasis configuration
Supporting non-default pre-emphasis settings for the internal and some external
PHYs

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15 23:31:41 -08:00
Eilon Greenstein c1b7399027 bnx2x: Using the HW 5th lane
This 1G interface (on top of the 4 lanes 10G interface) requires additional
setting to work in CL45

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15 23:31:36 -08:00
Eilon Greenstein 811a2f2d3b bnx2x: EMAC reset
The NIG_ENABLE does not reset the emac. Replace it with explicit reset

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15 23:31:33 -08:00
Eilon Greenstein 46c6a67495 bnx2x: PHY lock list
Some dual port PHY require HW lock since they are used by both interfaces
(different driver instances). Since this list is getting longer, update a
parameter at load time instead of calculating it on runtime

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15 23:31:26 -08:00
Eilon Greenstein 589abe3a0f bnx2x: Supporting BCM8726 PHY
Also adding the ability to recognize the optic module and disable it if it is
not authorized for safety reasons - since this feature might upset some users
which are willing to take the risk, it is optional and can be disabled by
setting an nvram bit (or a trivial driver patch to set this bit).
This dual port PHY requires special handling if the ports are swapped.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15 23:31:24 -08:00
Eilon Greenstein 4acac6a53a bnx2x: GPIO accessories
A GPIO is used with the 8726 PHY. Adding the GPIO related functions in this

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15 23:31:20 -08:00
Eilon Greenstein 1c06328c03 bnx2x: Flow control enhancement
Setting better HW thresholds and enabling FW capabilities for better
enforcement. Also set the HW to more efficiently use the internal buffers if
this is a single port design

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15 23:31:15 -08:00
Eilon Greenstein f1ef27ef42 bnx2x: Disabling interrupts after iSCSI-boot
Before initializing the chip after iSCSI boot, the interrupts of the function
that was used to boot must be disabled. That means that the driver needs to set
the chip as if it is the iSCSI PCI function - this bug is exposed only with MSI

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15 23:31:09 -08:00
Eilon Greenstein 8badd27aa0 bnx2x: MSI support
Enabling MSI on top of MSI-X and INTA. Also changing the module parameter to
allow choosing INTA or MSI even when MSI-X is available. The default status
block should not be reversed for endianity. Since MSI can issue
re-configuration, the interrupt disable function now requires mmiowb

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15 23:31:05 -08:00
Eilon Greenstein 8d9c5f34a2 bnx2x: New FW
This is the FW blob and the relevant definitions without any logic. It
also contains the minimal mandatory code changes to work with this FW
but it does not contain enabling of the new features that this FW
provides.

This FW is needed for:
- More efficient multi-queue
- per queue statistics
- Big-endian issue with MSI
- Improved pause response

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-02-15 23:24:08 -08:00
Eilon Greenstein d05c26ce69 bnx2x: Version update
Updating the version and the year of updated files

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-01-19 16:20:15 -08:00
Eilon Greenstein 3347162995 bnx2x: Spelling mistakes
Spelling mistakes
Spelling has to L's in it...

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-08-13 16:05:37 -07:00
Yaniv Rosner 8c99e7b043 bnx2x: Pause settings
Pause settings
- 1G pause was not working due to missing write to the emac block
  (TX_MODE_FLOW_EN)
- The flow control should use the negotiated result (after autoneg) so
  we should save both the requested autoneg and the result
- The HW credits with flow control at 1G speed were not optimized and
  caused low throughput
- It is recommended to turn off flow control if the MTU is bigger than
  5000B due to internal buffers size

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-08-13 16:04:30 -07:00
Yaniv Rosner 57963ed94c bnx2x: Link order with external PHY
Link order with external PHY
When external PHY exists (second chip with the PHY to translate to
another physical medium) the link with the eternal PHY and the network
should be established before setting the link between the 5771x and the
PHY. This is the right order and it is important when using autoneg -
the link to the network should use the autoneg and the link between the
two chips should be forced to the network result.

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-08-13 16:04:03 -07:00
Eilon Greenstein 5c86284817 bnx2x: PBA Table Page Alignment Workaround
PBA Table Page Alignment Workaround
The PBA table starts on the middle of the page and that's causing very
low performance with virtualization. The solution is not to update via
the BAR directly but via chip access to the same memory

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-08-13 16:03:37 -07:00
Eilon Greenstein 3fcaf2e566 bnx2x: HW attention lock
HW attention lock
Making sure that only one function will handle the HW attention. This
makes the device parameter aeu_mask redundant so it is removed

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-08-13 16:02:33 -07:00
Yitchak Gertner 4a37fb660c bnx2x: HW lock mechanism
HW lock mechanism
Enhancing the HW lock to work per function and not only per port - this
is needed for the next patch that protects races over HW attention
detection between the different functions. At this chance, changing the
functions names to be more inline with the current naming convention

Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-08-13 16:02:32 -07:00
Vladislav Zolotarov da5a662a23 bnx2x: Load/Unload under traffic
Load/Unload under traffic
Few issues were found when loading and unloading under traffic:
- When receiving Tx interrupt call netif_wake_queue if the queue is
  stopped but the state is open
- Check that interrupts are enabled before doing anything else on the
  msix_fp_int function
- In nic_load, enable the interrupts only when needed and ready for it
- Function stop_leading returns status since it can fail
- Add 1ms delay when unloading the driver to validate that there are no
  open transactions that already started by the FW
- Splitting the "has work" function into Tx and Rx so the same function
  will be used on unload and interrupts
- Do not request for WoL if only resetting the device (save the time
  that it takes the FW to set the link after reset)
- Fixing the device reset after iSCSI boot and before driver load - all
  internal buffers must be cleared before the driver is loaded

Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-08-13 16:02:04 -07:00
Yitchak Gertner 66e855f3f5 bnx2x: Statistics
Statistics
- Making sure that each drop is accounted for in the driver statistics
- Clearing the FW statistics when driver is loaded to prevent
  inconsistency with HW statistics
- Once error is detected (bnx2x_panic_dump), stop the statistics
  before other actions (currently it is stopped last and can corrupt
  the data) - Adding HW checksum error counter to the statistics
- Removing unused variable stats_ticks
- Using macros instead of magic numbers to indicate which statistics are
  shared per port and which are per function

Signed-off-by: Yitchak Gertner <gertner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-08-13 16:01:31 -07:00
Eilon Greenstein 34f80b04f3 bnx2x: Add support for BCM57711 HW
Supporting the 57711 and 57711E - refers to in the code as E1H. The
57710 is referred to as E1.

To support the new members in the family, the bnx2x structure was
divided to 3 parts: common, port and function. These changes caused some
rearrangement in the bnx2x.h file.

A set of accessories macros were added to make access to the bnx2x
structure more readable

Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-23 20:33:01 -07:00
Yaniv Rosner c18487ee24 bnx2x: New link code
New Link code:
Moving all the link related code (including the calculations, the
initialization of the MAC and PHY and the external PHY's code) into
a separated file. The changes from the code that used to be part of
bnx2x.c (now called bnx2x_main.c) are:
- Using separate structures for link inputs and link outputs to clearly 
  identify what was configured and what is the outcome
- Adding code to read external PHY FW version and print it as part of 
  ethtool -i
- Adding code to upgrade external PHY FW from ethtool -E with special 
  magic number - Changing the link down indication to ERR level
- Adding a lock on all PHY access to prevent an interrupt and 
  setting changes to overlap
- Adding support for emulation and FPGA (small chunk of code that really 
  helps in the lab) - Adding support for 1G on BCM8706 PHY
- Adding clear debug print incase of fan failure (the PHY type is now 
  "failure")

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-06-23 20:27:52 -07:00
Eliezer Tamir f14106478e [BNX2X]: Correct Link management
Properly protect PHY access between two devices on the same board with
a HW lock.

Use GPIO to clear all previous configurations before changing link
parameters.

Shut down the external PHY in case of fan failure.

Reducing the MDC/MDIO clock to 2.5MHz due to problems with some
devices.

Resolve the flow control response according to autoneg with external
PHY.

Unmasking all PHY interrupts in single write to prevent a race in the
interrupts order.

LASI indication fixes to work with peculiarities of PHYs.

Disable MAC RX to avoid a HW bug when closing the MAC under traffic.

Disable parallel detection on HiGig due to HW limitation.

Updating the shared memory structure to work with the current
bootcode.

Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-02-28 11:51:50 -08:00
Eliezer Tamir a2fbb9ea23 add bnx2x driver for BCM57710
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-01-28 15:03:53 -08:00