Adds more cases to do flogi retry, now also retry
on getting bad response due to either no ELS response
or flogi response payload length not large enough.
In those cases flogi was not retried and that
was leaving lport offline.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1745 commits)
dp83640: free packet queues on remove
dp83640: use proper function to free transmit time stamping packets
ipv6: Do not use routes from locally generated RAs
|PATCH net-next] tg3: add tx_dropped counter
be2net: don't create multiple RX/TX rings in multi channel mode
be2net: don't create multiple TXQs in BE2
be2net: refactor VF setup/teardown code into be_vf_setup/clear()
be2net: add vlan/rx-mode/flow-control config to be_setup()
net_sched: cls_flow: use skb_header_pointer()
ipv4: avoid useless call of the function check_peer_pmtu
TCP: remove TCP_DEBUG
net: Fix driver name for mdio-gpio.c
ipv4: tcp: fix TOS value in ACK messages sent from TIME_WAIT
rtnetlink: Add missing manual netlink notification in dev_change_net_namespaces
ipv4: fix ipsec forward performance regression
jme: fix irq storm after suspend/resume
route: fix ICMP redirect validation
net: hold sock reference while processing tx timestamps
tcp: md5: add more const attributes
Add ethtool -g support to virtio_net
...
Fix up conflicts in:
- drivers/net/Kconfig:
The split-up generated a trivial conflict with removal of a
stale reference to Documentation/networking/net-modules.txt.
Remove it from the new location instead.
- fs/sysfs/dir.c:
Fairly nasty conflicts with the sysfs rb-tree usage, conflicting
with Eric Biederman's changes for tagged directories.
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Except for obtaining the netdev from lport, fcoe_get_lesb is the common code
for the LLDs.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Acked-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently fcoe_ddp_min doesn't have default value
so by default not used, so setting up default value
as 4k as this works better by avoiding overhead
of programing DDP for small IOs.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use real dev in case it has HW vlan acceleration
support since in this case the real dev would
do needed vlan processing, this way unnecessary
vlan layer processing avoided and it gives
slightly better IOPS with 512B size IOs.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since fcoe_percpu_thread_create() creates percpu kthread, it makes sense
to use kthread_create_on_node() to get proper NUMA affinity for kthread
stack.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch does several things:
- introduces __ethtool_get_settings which is called from ethtool code and
from drivers as well. Put ASSERT_RTNL there.
- dev_ethtool_get_settings() is replaced by __ethtool_get_settings()
- changes calling in drivers so rtnl locking is respected. In
iboe_get_rate was previously ->get_settings() called unlocked. This
fixes it. Also prb_calc_retire_blk_tmo() in af_packet.c had the same
problem. Also fixed by calling __dev_get_by_index() instead of
dev_get_by_index() and holding rtnl_lock for both calls.
- introduces rtnl_lock in bnx2fc_vport_create() and fcoe_vport_create()
so bnx2fc_if_create() and fcoe_if_create() are called locked as they
are from other places.
- use __ethtool_get_settings() in bonding code
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
v2->v3:
-removed dev_ethtool_get_settings()
-added ASSERT_RTNL into __ethtool_get_settings()
-prb_calc_retire_blk_tmo - use __dev_get_by_index() and lock
around it and __ethtool_get_settings() call
v1->v2:
add missing export_symbol
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> [except FCoE bits]
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was pointed out by 'make versioncheck' that some includes of
linux/version.h are not needed in drivers/scsi/.
This patch removes them.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Export fcoe_get_wwn, fcoe_validate_vport_create and fcoe_wwn_to_str so that all
LLDs can use these common function.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Robert Love <robert.w.love@intel.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: devel@open-fcoe.org
Cc: linux-scsi@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup to:
- have selection for all types of frames, not just FCP.
- remove redundant cpu_online check once fcoe_select_cpu called
as this is not required since later code flow check for offlined
cpu.
- Simplify fcoe_select_cpu() by removing unnecessary checks to
skip curr_cpu, this also fixes possibly infinite loop in case
of curr_cpu is the only cpu while iterating in the loop.
This cleanup mainly applies to target as incoming request are
mostly for target, therefore Kiran has verified the patch
with target also.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use pending queue to retry FIP frame in case its tx
fails and use common pending queue for both fcoe
and fip frames using fcoe_port_send.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Drop the rx frame having xid with wrong cpu info
or received with xid not matching to our xid.
Not dropping such frame is causing panic as
that causes accessing data struct beyond their
bounds.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There is no need to cache the ptype in fcoe_rcv_info struct as it is never
used anywhere.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When NPIV port destroy handler is called it does not do all the cleanup
required for the given NPIV port. This was happening as some of the
lport cleanup moved to fcoe_interface_cleanup() routine, which is not
called as part of the vport delete process.
This patch rearranges the sequence in which the fcoe_if_destory() and
fcoe_interface_cleanup() functions are being called from various places
in the code. It now matches the sequence they are constructed during the
create process for both N_Port as well as NPIV port.
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Problem: Selection of RX queue on target is based on RX-ID. FCoE used
8 Net Rx queues. HW post the packets based on rx_id %
num_rx_queue. Due to this has based filtering, only one CPU is busy
servicing incoming request including post-processing of incoming
request. This is gating factor because
1. Only one CPU is utilized 100% while others CPUs are not used at all.
2. CPU which received request assign "sequence' by selecting exchange
from per CPU pool (num_ddp_context / num_online_cpus,
approxi.). Due to which if if rate of incoming request is higher
than rate of servicing request, existing code path end of sending
"BUSY" response (SAM_STAT_BUSY because unable to allocate
exchange).
Fix: Fan-out incoming request to all other CPUs excluding the CPU
which is receiving all incoiming request. This path also addresses,
selecting same CPU based on rx_id from received frame for completion
of the request such as "releasing exchange to the per CPU Pool". This
fix is applicable for FCoE target since initiator code path already
takes care of selecting CPU to complete post-processing of request
once OX_ID is assigned.
Notes: N/A
Dependencines: N/A
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Problem: Earlier mechanism of selection of CPU was, to select the same CPU
which has received incoming request. Hence in case of rx_id = 0xFFFF,
request was always posted to same NetRx queue, hence only 1 CPU is utilized
for handling the command. It was also causing problem of "running out of
exchanges from per CPU pool of exchanges (in case of DDP offload)
Fix: Implemented new algo. to select CPU for post-processing of
incoming commands when rx_id is unknown. This is simple Round robin
algo. for CPU selection.
Notes/Dependencies: N/A
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Problem: When initiator sends write command to target, target tries to
assign new sequence. It allocates new exchangeID (RX_ID)
always from non-offloaded pool (Non-offload EMA)
Fix: Enhanced fcoe_oem_match routine to look at F_CTL flags and if it
is exchange responder and command type is WRITEDATA, then function
returns TRUE instead of FALSE. This function is used to determine
which pool to use (offload pool of exchange is used only if this
function returns TRUE).
Technical Notes: N/A
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add ddp_target() support to the Open-FCoE sw fcoe hba driver (fcoe.ko).
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libfcoe's interface consists of create, destroy, enable,
disable and create_vn2vn. These are currently module
paramaters added durring the module initialization. A
concern arose that the module parameters were being added
with write permissions before the module had completed
initialization. The following code was added to each
sysfs store file.
* Make sure the module has been initialized, and is not about to be
* removed. Module parameter sysfs files are writable before the
* module_init function is called and after module_exit.
*/
if (THIS_MODULE->state != MODULE_STATE_LIVE)
goto out_nodev;
This check was called out as unhelpful as the module can
go dead at any time and therefore its state isn't a reliable
thing to look at as a sign of stability and initialization
completion. Also, that functional interfaces like these
should be added after module initialization.
This patch removes the unnecessary checks and hopes to
disprove the concern about initialization ordering.
Recent fcoe transport rework changes now require fcoe
transports to register with libfcoe before any operation
can take place. libfcoe may access some static variables
but nothing that could cause a problem. Once a fcoe transport
is registered, libfcoe is usable and any interface calls will
be functional.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
This patch adds a validation step before allowing creation of a new NPIV port.
It checks whether the WWPN passed for the new NPIV port to be created is unique
for the given physical port.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Host doesnt handle CVL to NPIV instantiated ports correctly.
- As per FC-BB-5 Rev 2 CVLs with no VN_Port descriptors shall be treated as
implicit logout of ALL vn_ports.
- CVL for NPIV ports should be handled before physical port even if descriptor
for physical port appears before NPIV ports
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
Currently fcoe interface cleanup is done after ndo_fcoe_disable
and that prevents logoff going out to the peer, so this patch
moves all netdev cleanup and its releasing inside
fcoe_interface_cleanup to have log off before ndo_fcoe_disable
disables the fcoe.
This patch also fixes asymmetric rtnl locking around fcoe_if_destroy,
as currently this function requires rtnl held by its caller
and then have this func drops the lock, instead now don't have
any processing under rtnl inside fcoe_if_destroy, this required
moving few func to get build working again.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
fix typo of '_attach' -> '_detach' in the comment.
Reported-by: Frank Zhang <frank_1.zhang@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
possible buffer overflow in fcoe_transport_show when reaching the end of
buffer and crossing PAGE_SIZE boundary.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When rmmoving the underlying fcoe transport driver module by force when
it's attached and in use, the correspoding netdev mapping should be
cleaned up properly as well, otherwise the lookup for a given netdev
for the transport would still return non NULL pointer, causing "unable
to handle paging request" bug.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The check of module state being MODULE_STATE_LIVE is no longer needed for the
individual fcoe transport driver, e.g., fcoe.ko, as sysfs entries now go to
libfcoe now, if it reaches fcoe.ko, it has to be already registered. The module
state check for libfcoe will guard the possible race condition of sysfs being
writable before module_init function is called and after module_exit.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
These checks were initially added to avoid a lockdep
false positive when dealing with the s_active, rtnl
and fcoe_config_mutex mutexes. Recently the create,
destroy, enable and disable sysfs entries were moved
from fcoe.ko to libfcoe.ko. With this change the mutex
usage was shuffled around and the lockdep false
positive stopped happening. We can now remove these
checks.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This code was incorrectly ported from fcoe.c when the
fcoe transport infrastructure was put into place. It
was originally needed in fcoe.c when dealing with
the rtnl mutex. In that code it was only needed to
avoid a lockdep false positive. In libfcoe we don't
deal with the rtnl mutex, we don't get the lockdep
false positive and therefore we don't need these
checks.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This makes sure that when a driver calls the ethtool's
get/set_settings() callback of another driver, the data passed to it
is clean. This guarantees that speed_hi will be zeroed correctly if
the called callback doesn't explicitely set it: we are sure we don't
get a corrupted speed from the underlying driver. We also take care of
setting the cmd field appropriately (ETHTOOL_GSET/SSET).
This applies to dev_ethtool_get_settings(), which now makes sure it
sets up that ethtool command parameter correctly before passing it to
drivers. This also means that whoever calls dev_ethtool_get_settings()
does not have to clean the ethtool command parameter. This function
also becomes an exported symbol instead of an inline.
All drivers visible to make allyesconfig under x86_64 have been
updated.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (170 commits)
[SCSI] scsi_dh_rdac: Add MD36xxf into device list
[SCSI] scsi_debug: add consecutive medium errors
[SCSI] libsas: fix ata list corruption issue
[SCSI] hpsa: export resettable host attribute
[SCSI] hpsa: move device attributes to avoid forward declarations
[SCSI] scsi_debug: Logical Block Provisioning (SBC3r26)
[SCSI] sd: Logical Block Provisioning update
[SCSI] Include protection operation in SCSI command trace
[SCSI] hpsa: fix incorrect PCI IDs and add two new ones (2nd try)
[SCSI] target: Fix volume size misreporting for volumes > 2TB
[SCSI] bnx2fc: Broadcom FCoE offload driver
[SCSI] fcoe: fix broken fcoe interface reset
[SCSI] fcoe: precedence bug in fcoe_filter_frames()
[SCSI] libfcoe: Remove stale fcoe-netdev entries
[SCSI] libfcoe: Move FCOE_MTU definition from fcoe.h to libfcoe.h
[SCSI] libfc: introduce __fc_fill_fc_hdr that accepts fc_hdr as an argument
[SCSI] fcoe, libfc: initialize EM anchors list and then update npiv EMs
[SCSI] Revert "[SCSI] libfc: fix exchange being deleted when the abort itself is timed out"
[SCSI] libfc: Fixing a memory leak when destroying an interface
[SCSI] megaraid_sas: Version and Changelog update
...
Fix up trivial conflicts due to whitespace differences in
drivers/scsi/libsas/{sas_ata.c,sas_scsi_host.c}
Check for bonding master and refuse to use that.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Robert Love <robert.w.love@intel.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset using "fcoeadm -r" also needs to restart FIP before
doing libfc lport reset, this is needed for new switch firmware
requiring FIP solicitation before doing FLOGI again during reset.
So this patch does this by doing fcoe_ctlr_link_down and then
fcoe_ctlr_link_up to reset the interface.
The fcoe_ctlr_link_down call path also does lport reset
and then fcoe_ctlr_link_up re-starts the fabric login after
doing FIP solicitation first to get reset feature working
again.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Negate has higher precedence than bitwise AND. FCPHF_CRC_UNCHECKED is
0x1 so the original code is equivalent to: if (!fr_flags(fp)) { ...
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When L2 driver is unloaded, libfcoe_destroy tries to access the fcoe
transport structure matching the netdev. However, since the netdev is
unregistered by that time, it fails to do so. Hence the stale mappings
exists in the fcoe-netdev list. Handle NETDEV_UREGISTER device
notification mechanism to remove the stale fcoe-netdev mapping.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
both fcoe and bnx2fc drivers can access the common definition of
FCOE_MTU.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
EM anchors list initialization for only master port was not enough to
keep npiv working as described here:-
https://lists.open-fcoe.org/pipermail/devel/2011-January/011063.html
So this patch moves fc_exch_mgr_list_clone to update npiv ports
EMs once EM anchors list initialized.
Also some cleanup, no need to set lport = NULL as that always
get initialized later.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
To facilitate LLDDs to reuse the code, skb queue related functions are moved to
libfcoe, so that both fcoe and bnx2fc drivers can use them. The common structures
fcoe_port, fcoe_percpu_s are moved to libfcoe. fcoe_port will now have an
opaque pointer that points to corresponding driver's interface structure.
Also, fcoe_start_io and fcoe_fc_crc are moved to libfcoe.
As part of this change, fixed fcoe_start_io to return ENOMEM if
skb_clone fails.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
fcoe uses the system_wq to destroy ports and the work items need to be
flushed before the driver is unloaded. As the work items free the
containing data structure, they can't be flushed directly. The
workqueue should be flushed instead.
Also, the destruction works can be chained - ie. destruction of a port
may lead to destruction of another port where the work item for the
former queues the work for the latter. Currently, the depth of chain
can be at most two and fcoe_exit() makes sure everything is complete
by calling flush_scheduled_work() twice.
With commit c8efcc25 (workqueue: allow chained queueing during
destruction), destroy_workqueue() can take care of chained works on
workqueue destruction. Add and use fcoe_wq instead. Simply
destroying fcoe_wq on driver unload takes care of flushing.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove the existing sysfs entry points of the fcoe.ko module parameters that
are used to create/destroy/enable/disable an FCoE instance, rather, use the
newly added fcoe transport code to attach itself as an FCoE transport provider
when fcoe.ko gets loaded. There is no functionality change on the logic of
fcoe interacts with upper libfc and lower netdev. The fcoe transport only acts
as thin layer to provide a unified interface for all fcoe transport providers
so all FCoE instances on any network interfaces from all vendors can be
managed through the same Open-FCoE.org's user space tool package, which also
has full DCB support.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Prepare the fcoe to convert it to use the newly added fcoe transport, making
it as the default fcoe transport provider for libfcoe. This patch is to rename
some of the variables to avoid any confusing names later as now there are
several transports in the same file.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Now we can include the fcoe_transport.c to the build of the kernel libfcoe
module. Move the module information to fcoe_transport, and it will have
all the module parameters later for the create/destroy/enable/disable of an
FCoE instance.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The existing libfcoe.c is mostly for FIP support, rename it to reflect that
fact and so we can add fcoe_transport.c to the make file to include both
into the libfcoe kernel module.
[ Minor modifications by Robert Love converting a few
"__attribute__((packed))" modifiers to "__packed" to remove new
checkpatch.pl WARNINGS ]
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add the new fcoe_transport.c file that implements basic fcoe transport
interface. Eventually, the sysfs entries to create/destroy/enable/disable
an FCoE instance will be coming to the fcoe transport layer, who does a
look-up to find the corresponding transport provide and pass the corresponding
action over to the identified provider.
The fcoe.ko will become the default fcoe transport provider that can support
FCoE on any given netdev interfaces, as the Open-FCoE.org's default software
FCoE HBA solution. Any vendor specific FCoE HBA driver that is built on top
of Open-FCoE's kernel stack of libfc & libfcoe as well as the user land tool
of fcoe-utils can easily plug-in and start running FCoE on their network
interfaces. The fcoe.ko will be converted to act as the default provider if
no vendor specific transport provider is found, as it is always added to the
very end of the list of attached transports.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
libfcoe kernel module debug macros will used by the fcoe transport code
as well when later it gets added.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Allowing FCoE LOGO followed by CVL in this case prevents
FIP login back to the FCF and then keeps lport offline,
only FIP LOGO and CLV needs to be processed while in
FIP mode, therefore this patch drops FCoE LOGO in FIP mode.
Added fcoe_filter_frames() to filter out above mentioned LOGO
in fcoe rx path along with other existing filtering in code
for bad CRC frames. Adding separate fcoe_filter_frames function
helped with better code indentations and if needed then same
will allow adding more filters at one place in future.
This LOGO drop is added after FCP frames passed up to avoid
any additional checks on fast path for this.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
vports are not grabbing module references but are
releasing them. This causes the module reference count
to decrement too many times and it wraps around past 0.
The solution is to do a module_put() in
fcoe_interface_release() so that the reference is only
released when the fcoe_interface is released. There is a
one-to-one relationship between the N_Port and the
fcoe_interface, so the module reference will only be
dropped when the N_Port is destroyed
To create symetry in the code this patch moves the
try_module_get() call into fcoe_interface_create(). This
means that only the N_Port will grab a reference to the
module when its corresponding fcoe_interface is created.
This patch also makes it so that the fcoe_interface_create()
routine encodes any error codes in the fcoe_interface
pointer returned. This way its caller, fcoe_create(), can
return an accurate error code.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Neaten several calls to fip_select() by having it return the
pointer to the new FCF.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When there are several FCFs to choose from, the one most likely
to accept a FLOGI on certian switches is the one that last
answered a multicast solicit.
So, when receiving an advertisement, move the FCF to the front
of the list so that it gets chosen first among those with the
same priority.
Without this, more FLOGIs need to be sent in a test with
multiple FCFs and a switch in NPV mode, but it still
eventually finds one that accepts the FLOGI.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When multiple FCFs to the same fabric exist, the debug messages
all look alike. Change the message to include the MAC address.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Switches using multiple-FCFs may reject FLOGI in order to
balance the load between multiple FCFs. Even though the FCF
was available, it may have more load at the point we actually
send the FLOGI.
If the FLOGI fails, select a different FCF
if possible, among those with the same priority. If no other
FCF is available, just deliver the reject to libfc for retry.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The check for conflicting fabrics in fcoe_ctlr_select()
ignores any FCFs that aren't usable. This is a minor
problem now but becomes more pronounced after later patches.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Move some of the code in fcoe_ctlr_timer_work() to
fcoe_ctlr_select() so that it can be shared
with another function in a forthcoming patch.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Move the announcement code to a separate function for reuse in
a forthcoming patch.
For messages regarding FCF timeout and selection, use the
previously-announced FCF MAC address (dest_addr) in the fcoe_ctlr struct.
Only print (announce) the FCF if it is new. Print MAC for
timed-out or deselected FCFs.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add missing newlines.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This happens when then tearing down the fcoe interface with active I/O.
The back trace shows dead000000200200 in RAX, i.e., LIST_POISON2, indicating
that the fsp is already being dequeued, which is probably why no complaining
was seen in fc_fcp_destroy() about outstanding fsp not freed, since we dequeue
it in the end of fc_io_compl() before releasing it. The bug is due to the
fact that we have already destroyed lport's scsi_pkt_pool while on-going i/o
is still accessing it through fc_fcp_pkt_release(), like this trace or the
similar code path from scsi-ml to fc_eh_abort, etc. This is fixed by moving
the fc_fcp_destroy() after lport is detached from scsi-ml since fc_fcp_destroy
is supposed to called only once where no lport lock is taken, otherwise the
fc_fcp_pkt_release() would have to grab the lport lock.
BUG: unable to handle kernel NULL pointer dereference at (null)
.......
RIP: 0010:[<0000000000000000>]
[<(null)>] (null)
RSP: 0018:ffff8803270f7b88 EFLAGS: 00010282
RAX: dead000000200200 RBX: ffff880197d2fbc0 RCX: 0000000000005908
RDX: ffff880195ea6d08 RSI: 0000000000000282 RDI: ffff880180f4fec0
RBP: ffff8803270f7bc0 R08: ffff880197d2fbe0 R09: 0000000000000000
R10: ffff88032867f090 R11: 0000000000000000 R12: ffff880195ea6d08
R13: 0000000000000282 R14: ffff880180f4fec0 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff8801b5820000(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000000 CR3: 00000001a6eae000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process fc_rport_eq (pid: 5278, threadinfo ffff8803270f6000, task ffff880326254ab0)
Stack:
ffffffffa02c39ca ffff8803270f7ba0 ffff88019331cbc0 ffff880197d2fbc0
0000000000000000 ffff8801a8c895e0 ffff8801a8c895e0 ffff8803270f7c10
ffffffffa02c4962 ffff8803270f7be0 ffffffff814c94ab ffff8803270f7c10
Call Trace:
[<ffffffffa02c39ca>] ? fc_io_compl+0x10a/0x530 [libfc]
[<ffffffffa02c4962>] fc_fcp_complete_locked+0x72/0x150 [libfc]
[<ffffffff814c94ab>] ? _spin_unlock_bh+0x1b/0x20
[<ffffffffa02b98ff>] ? fc_exch_done+0x3f/0x60 [libfc]
[<ffffffffa02c4a8f>] fc_fcp_retry_cmd+0x4f/0x60 [libfc]
[<ffffffffa02c6150>] fc_fcp_recv+0x9b0/0xc30 [libfc]
[<ffffffff8106ba7a>] ? _call_console_drivers+0x4a/0x80
[<ffffffff8107d5ec>] ? lock_timer_base+0x3c/0x70
[<ffffffff8107e06b>] ? try_to_del_timer_sync+0x7b/0xe0
[<ffffffffa02b9dcf>] fc_exch_mgr_reset+0x1df/0x250 [libfc]
[<ffffffffa02c57a0>] ? fc_fcp_recv+0x0/0xc30 [libfc]
[<ffffffffa02c1042>] fc_rport_work+0xf2/0x4e0 [libfc]
[<ffffffff8109203e>] ? prepare_to_wait+0x4e/0x80
[<ffffffffa02c0f50>] ? fc_rport_work+0x0/0x4e0 [libfc]
[<ffffffff8108c6c0>] worker_thread+0x170/0x2a0
[<ffffffff81091d50>] ? autoremove_wake_function+0x0/0x40
[<ffffffff8108c550>] ? worker_thread+0x0/0x2a0
[<ffffffff810919e6>] kthread+0x96/0xa0
[<ffffffff810141ca>] child_rip+0xa/0x20
[<ffffffff81091950>] ? kthread+0x0/0xa0
[<ffffffff810141c0>] ? child_rip+0x0/0x20
Code:
Bad RIP value.
RIP
[<(null)>] (null)
RSP <ffff8803270f7b88>
CR2: 0000000000000000
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
A previous patch attempted to validate the destination
MAC address of a FCoE frame by checking that MAC
address against the received port's MAC address. The
implementation seems fine on the surface, but any
VN_Ports added using the NPIV feature will have their
own MAC addresses and these MACs were not being checked,
which prevented any NPIV VN_Ports from receiving frames.
In other words, the following patch has broken NPIV.
519e5135e2
[SCSI] fcoe: adds src and dest mac address
checking for fcoe frames
Part of the offending patch is correct, but the part
that broke NPIV was attempting to satisfy FC-BB-5
section D.5, 2.1-
(discard frames that) "contain a destination MAC
address/destination N_Port_ID pair that was not
assigned by an FCF to one of the VN_Ports on the ENode"
The language does _not_ say to compare the destination
FC-MAP/destination N_Port_ID, but instead to compare
the destination MAC address/destination N_Port_ID.
>From the FC-BB-5 specification,
"A properly formed FPMA is one in which the 24 most
significant bits equal the Fabric’s FC-MAP value and
the least significant 24 bits equal the N_Port_ID
assigned to the VN_Port by the FCF."
This means that we need to compare the FC Frame's
destination FCID against the embedded FCID in the
destination MAC address. This patch checks the lower
24 bits of the destination MAC address against
destination FCID in the Fibre Channel frame.
For MAC validation the first line of defense is the
hardware MAC filtering. Each VN_Port will have a
unicast MAC addresses added to the hardware's
filtering table. The Ethernet driver should drop any
MACs not destined for a programmed MAC. This patch
adds a second line of defense that very specfically
compares an element in the FC frame against an element
in the Ethernet header, which is appropriate for the
FCoE layer.
Many alternative approaches were considered, including
a LLD callback from libfc. The second most reasonable
approach seemed to be walking the list of NPIV ports
and check each of their MAC addresses against the
destination MAC address of the received frame. The
problem with this approach was that it is likely that
performance would suffer with the more NPIV ports added
to the system since every received frame would need to
walk this list, comparing each entry's MAC.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix: When FIP frame is received, function fcoe_ctlr_vn_recv calls function
fcoe_ctlr_vn_parse which does memset for addr (&buf.rdata) which leads to
memory corruption. Code was trying to treat "buf" as struct but it was defined
as union. Fix is to change from union to struct for "buf" in function fcoe_ctlr_vn_recv.
Technical Details: N/A
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Acked-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Since sometimes current FIP_MODE_AUTO mode falls back to non-FIP
mode while DCB link still getting ready in fabric mode with
its peer switch, it falls back after few libfc flogi retries
and that is not we want while working with FIP enabled
switches in FABRIC mode, therefore sets default as FIP_MODE_FABRIC
as discussed and agreed before in this mail thread
http://www.open-fcoe.org/pipermail/devel/2010-August/010511.html
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (276 commits)
[SCSI] zfcp: Trigger logging in the FCP channel on qdio error conditions
[SCSI] zfcp: Introduce experimental support for DIF/DIX
[SCSI] zfcp: Enable data division support for FCP devices
[SCSI] zfcp: Prevent access on uninitialized memory.
[SCSI] zfcp: Post events through FC transport class
[SCSI] zfcp: Cleanup QDIO attachment and improve processing.
[SCSI] zfcp: Cleanup function parameters for sbal value.
[SCSI] zfcp: Use correct width for timer_interval field
[SCSI] zfcp: Remove SCSI device when removing unit
[SCSI] zfcp: Use memdup_user and kstrdup
[SCSI] zfcp: Fix retry after failed "open port" erp action
[SCSI] zfcp: Fail erp after timeout
[SCSI] zfcp: Use forced_reopen in terminate_rport_io callback
[SCSI] zfcp: Register SCSI devices after successful fc_remote_port_add
[SCSI] zfcp: Do not try "forced close" when port is already closed
[SCSI] zfcp: Do not unblock rport from REOPEN_PORT_FORCED
[SCSI] sd: add support for runtime PM
[SCSI] implement runtime Power Management
[SCSI] convert to the new PM framework
[SCSI] Unify SAM_ and SAM_STAT_ macros
...
This check prevents FCF selection in NPV mode due to zero fabric name
in that case and in turn flogi fails. Though NPV mode should not have
this zero and should be fixed there also but spec also does not require
initiator to ensure that fabric name must be non-zero, therefore dropping
this check to get flogi working in NPV mode.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This reverts commit cc0136c2e9.
That commit introduced vlan id info to WWPN but WWPN needs to
remain static as an unique port identifier in the fabric, therefore
variable fabric vlan id info doesn't need to be coded inside WWPN.
After this revert, port arg to fcoe_wwn_from_mac is always zero
but still leaving it as-is okay to later allow users to use NAA 2
scheme with this additional port arg.
Note with this patch, existing zoning using WWPN would require
re-zoning this time only and later no more re-zoning due to any
vlan id changes.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently, when FCoE netdev feature flags are toggled by the LLD, lport's
corresponding flags are not updated. This causes the fc_fcp to still try to
offload the I/O. This patch adds support of NETDEV_FEAT_CHANGE event in fcoe
netdev device notification callback so we can update the lport offload flags
appropriately.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Incoming requests shouldn't require a local exchange if we're
just going to reply with one or two frames and don't expect
anything further. Don't allocate exchanges for such requests
until requested by the upper-layer protocol.
The sequence is always NULL for new requests, so remove
that as an argument to request handlers.
Also change the first argument to lport->tt.seq_els_rsp_send
from the sequence pointer to the received frame pointer, to
supply the exchange IDs and destination ID info.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add module parameter create_vn2vn that behaves like the create
parameter except that the new instance is created in FIP vn2vn mode.
This can be replaced once we change create to allow modifying
per-instance attributes before starting the instance.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In VN2VN mode, map_dest means to use the default VN2VN OUI.
Change code that uses the default FCoE OUI to use the one
set in the fcoe_ctlr struct.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When sending a FLOGI LS_ACC, which we only do in point-to-multipoint
mode, the MAC descriptor should have the granted MAC set to
0x0efd00 || D_ID.
When sending an LS_RJT, there should be no MAC descriptor.
When sending either an LS_ACC or LS_RJT, the subcode should indicate
an reply, not a request.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The FC-BB-6 committee is proposing a new FIP usage model called
VN_port to VN_port mode. It allows VN_ports to discover each other
over a loss-free L2 Ethernet without any FCF or Fibre-channel fabric
services. This is point-to-multipoint. There is also a variant
of this called point-to-point which provides for making sure there
is just one pair of ports operating over the Ethernet fabric.
We add these new states: VNMP_START, _PROBE1, _PROBE2, _CLAIM, and _UP.
These usually go quickly in that sequence. After waiting a random
amount of time up to 100 ms in START, we select a pseudo-random
proposed locally-unique port ID and send out probes in states PROBE1
and PROBE2, 100 ms apart. If no probe responses are heard, we
proceed to CLAIM state 400 ms later and send a claim notification.
We wait another 400 ms to receive claim responses, which give us
a list of the other nodes on the network, including their FC-4
capabilities. After another 400 ms we go to VNMP_UP state and
should start interoperating with any of the nodes for whic we
receivec claim responses. More details are in the spec.j
Add the new mode as FIP_MODE_VN2VN. The driver must specify
explicitly that it wants to operate in this mode. There is
no automatic detection between point-to-multipoint and fabric
mode, and the local port initialization is affected, so it isn't
anticipated that there will ever be any such automatic switchover.
It may eventually be possible to have both fabric and VN2VN
modes on the same L2 network, which may be done by two separate
local VN_ports (lports).
When in VN2VN mode, FIP replaces libfc's fabric-oriented discovery
module with its own simple code that adds remote ports as they
are discovered from incoming claim notifications and responses.
These hooks are placed by fcoe_disc_init().
A linear list of discovered vn_ports is maintained under the
fcoe_ctlr struct. It is expected to be short for now, and
accessed infrequently. It is kept under RCU for lock-ordering
reasons. The lport and/or rport mutexes may be held when we
need to lookup a fcoe_vnport during an ELS send.
Change fcoe_ctlr_encaps() to lookup the destination vn_port in
the list of peers for the destination MAC address of the
FIP-encapsulated frame.
Add a new function fcoe_disc_init() to initialize just the
discovery portion of libfcoe for VN2VN mode.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Enhancement: add debug messages at all state transitions.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
There are three modes that libfcoe currently supports, and a new one
is coming. Change the fcoe_ctlr_init() interface to add the mode
desired. This should not change any functionality.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
It turns out most of the FIP work is now done from worker threads
or process context now, so there's no need to use a spin lock.
Change to use mutex instead of spin lock and delayed_work instead
of a timer.
This will make it nicer for the VN_port to VN_port feature that
will interact more with the libfc layers requiring that
spinlocks not be held.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This is per FC-BB-5 Annex-D recommendation and per that
if address checking fails then drop the frame.
FIP code paths are already doing this so only needed for fcoe
frames.
The src address checking is limited to only fip mode since
this might break non-fip mode used in p2p due to used OUI
based addressing in some p2p code paths, going forward FIP
will be the only mode, therefore limited this to only FIP
mode so that it won't break non-fip p2p mode for now.
-v2
Removes FCOE packet type checking since fcoe_rcv is
registered to receive only FCoE type packets from netdev
and it is already checked by netdev.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The fc_fabric_logoff and fc_fabric_login are redundant
here after recently added fcoe_ctlr_link_down/up to
these functions, therefore this patch removes logoff
and login to only use link down and up here. This works
best for their current usages with fcoe DCB link down or up.
This also works well to avoid EIO errors when fcoe DCB link
goes down as lport state moves out of ready quickly from
fcoe_ctlr_link_down and that allows re-queuing timed out IOs
for this case also.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
As per FC-BB-5 rev.2, section 7.8.7.1, strict ordering of FIP descriptors
is required for ELS requests. Also, look for missing and duplicate critical
descriptors.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Clear virtual link for NPIV ports is now handled by resetting
the matching vnport.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
As per FC-BB-5 rev 2, section 7.8.6.2, malformed FIP frame shall be
discarded. Drop discovery adv, ELS and CLV's with duplicate critical
descriptors.
[Resending after incorporating Joe's review comments]
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Allow the D flag (indicating that keep-alives are not needed) to
be updated dynamically from received FIP advertisements.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
keep alives are disabled due to fd_flags set and also
stop updating keep alive values in that case.
Update select fcf time only if fcf is not already selected or
select time is not already determined from parse adv, and then
have select time cleared only once after fcf is selected.
Changed deadline check to time_after_eq() from time_after()
since now next timeout will be on exact 2.5 times FKA followed
by first advertisement.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
[This patch has several improvements to the code in
the fip timers. It hasn't been tested yet.
I'm sending it out for review. Vasu, perhaps you can
merge this with your patch and test it together.]
The current code allows an advertisement to be used
even if it has been 3 times the FCF keep-alive
advertisement period (FKA) since one was received from
that FCF. The spec. calls for 2.5 times FKA.
Fix this and make sure we detect missed keep-alives promptly.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Host does not send discovery solicitation messages if Disc. Adv
from FCF are dropped. It restarts sending solicitation only
after receiving a Discovery Adv. from FCF. Fix is to restart
solicitation immediately after CVL processing.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Avoid infinite loop while processing FIP ELS or discovery
advertisement with non-critical descriptors.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Acked-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
A check in fcoe_ctlr_send_keep_alive() returns if there's no
port_id for the local port. This could miss a keep alive if
we just did a host reset and have logged off and will log back in.
Return only if we are doing the port keep alive, in which case
we need to be logged in.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
There is a small possibility that a reader gets incorrect values on 32
bit arches. SNMP applications could catch incorrect counters when a
32bit high part is changed by another stats consumer/provider.
One way to solve this is to add a rtnl_link_stats64 param to all
ndo_get_stats64() methods, and also add such a parameter to
dev_get_stats().
Rule is that we are not allowed to use dev->stats64 as a temporary
storage for 64bit stats, but a caller provided area (usually on stack)
Old drivers (only providing get_stats() method) need no changes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- C99 knows about USHRT_MAX/SHRT_MAX/SHRT_MIN, not
USHORT_MAX/SHORT_MAX/SHORT_MIN.
- Make SHRT_MIN of type s16, not int, for consistency.
[akpm@linux-foundation.org: fix drivers/dma/timb_dma.c]
[akpm@linux-foundation.org: fix security/keys/keyring.c]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (182 commits)
[SCSI] aacraid: add an ifdef'd device delete case instead of taking the device offline
[SCSI] aacraid: prohibit access to array container space
[SCSI] aacraid: add support for handling ATA pass-through commands.
[SCSI] aacraid: expose physical devices for models with newer firmware
[SCSI] aacraid: respond automatically to volumes added by config tool
[SCSI] fcoe: fix fcoe module ref counting
[SCSI] libfcoe: FIP Keep-Alive messages for VPorts are sent with incorrect port_id and wwn
[SCSI] libfcoe: Fix incorrect MAC address clearing
[SCSI] fcoe: fix a circular locking issue with rtnl and sysfs mutex
[SCSI] libfc: Move the port_id into lport
[SCSI] fcoe: move link speed checking into its own routine
[SCSI] libfc: Remove extra pointer check
[SCSI] libfc: Remove unused fc_get_host_port_type
[SCSI] fcoe: fixes wrong error exit in fcoe_create
[SCSI] libfc: set seq_id for incoming sequence
[SCSI] qla2xxx: Updates to ISP82xx support.
[SCSI] qla2xxx: Optionally disable target reset.
[SCSI] qla2xxx: ensure flash operation and host reset via sg_reset are mutually exclusive
[SCSI] qla2xxx: Silence bogus warning by gcc for wrap and did.
[SCSI] qla2xxx: T10 DIF support added.
...
Currently fcoe module ref count is used for tracking
active fcoe instances, it means each fcoe instance create
increments the count while destroy dec the count.
The dec is done only if fcoe instance is destroyed from
/sysfs but not if destroyed due to NETDEV_UNREGISTER event.
So this patch moves only module_put doing dec to common
fcoe_if_destroy function, so that dec would occur on ever
fcoe instance destroy.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
All VNports are sending FIP Keep-Alive messages with port_id and wwpn of the parent host instead of it's own port_id and wwpn. Standard FIP descriptor type 11 indicates to send own port_id and port_name.
Signed-off-by: Kaladhar Musunuru <kmusunuru@juniper.net>
Acked-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix typo in memset. Incorrect length parameter to memset resulting non-zero MAC address in FPMA messages.
Signed-off-by: Kaladhar Musunuru <kmusunuru@juniper.net>
Acked-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently rtnl mutex is grabbed during fcoe create, destroy, enable
and disable operations while sysfs s_active read mutex is already
held, but simultaneously other networking events could try grabbing
write s_active mutex while rtnl is already held and that is causing
circular lock warning, its detailed log pasted at end.
In this log, the rtnl was held before write s_active during device
renaming but there are more such cases as Joe reported another
instance with tg3 open at:-
http://www.open-fcoe.org/pipermail/devel/2010-February/008263.html
This patch fixes this issue by not waiting for rtnl mutex during
fcoe ops, that means if rtnl mutex is not immediately available
then restart_syscall() to allow others waiting in line to
grab s_active along with rtnl mutex to finish their work first
under these mutex.
Currently rtnl mutex was grabbed twice during fcoe_destroy call flow,
second grab was from fcoe_if_destroy called from fcoe_destroy after
dropping rtnl mutex before calling fcoe_if_destroy, so instead made
fcoe_if_destroy always called with rtnl mutex held to have this mutex
grabbed only once in this code path.
However left matching rtnl_unlock as-is in its original place as it was
dropped there for good reason since very next call causes synchronous
fip worker flush and if rtnl mutex is still held before flush
then that would cause new circular warning between fip->recv_work and
rtnl mutex, I've added detailed comment for this on fcoe_if_destroy
calling and rtnl muxtes unlocking.
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.33.1linux-stable-2.6.33 #1
-------------------------------------------------------
fcoemon/18823 is trying to acquire lock:
(fcoe_config_mutex){+.+.+.}, at: [<ffffffffa02ba5fc>] fcoe_create+0x27/0x4f7
[fcoe]
but task is already holding lock:
(s_active){++++.+}, at: [<ffffffff8115ef93>] sysfs_get_active_two+0x31/0x48
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (s_active){++++.+}:
[<ffffffff81077bdb>] __lock_acquire+0xb73/0xd2b
[<ffffffff81077e60>] lock_acquire+0xcd/0xf1
[<ffffffff8115e5df>] sysfs_deactivate+0x8b/0xe0
[<ffffffff8115edfb>] sysfs_addrm_finish+0x36/0x55
[<ffffffff8115d0cc>] sysfs_hash_and_remove+0x53/0x6a
[<ffffffff8115f353>] sysfs_remove_link+0x21/0x23
[<ffffffff812b6c93>] device_rename+0x99/0xcb
[<ffffffff8138dbf0>] dev_change_name+0xd5/0x1d2
[<ffffffff8138deee>] dev_ifsioc+0x201/0x2ac
[<ffffffff8138e4ba>] dev_ioctl+0x521/0x632
[<ffffffff81379e43>] sock_do_ioctl+0x3d/0x47
[<ffffffff8137a254>] sock_ioctl+0x213/0x222
[<ffffffff81114614>] vfs_ioctl+0x32/0xa6
[<ffffffff81114b94>] do_vfs_ioctl+0x490/0x4d6
[<ffffffff81114c30>] sys_ioctl+0x56/0x79
[<ffffffff81009b42>] system_call_fastpath+0x16/0x1b
-> #1 (rtnl_mutex){+.+.+.}:
[<ffffffff81077bdb>] __lock_acquire+0xb73/0xd2b
[<ffffffff81077e60>] lock_acquire+0xcd/0xf1
[<ffffffff8142f343>] __mutex_lock_common+0x4b/0x383
[<ffffffff8142f73f>] mutex_lock_nested+0x3e/0x43
[<ffffffff813959f9>] rtnl_lock+0x17/0x19
[<ffffffff8138ccae>] register_netdevice_notifier+0x1e/0x19b
[<ffffffffa02580c1>] 0xffffffffa02580c1
[<ffffffff81002069>] do_one_initcall+0x5e/0x15e
[<ffffffff81084094>] sys_init_module+0xd8/0x23a
[<ffffffff81009b42>] system_call_fastpath+0x16/0x1b
-> #0 (fcoe_config_mutex){+.+.+.}:
[<ffffffff81077a85>] __lock_acquire+0xa1d/0xd2b
[<ffffffff81077e60>] lock_acquire+0xcd/0xf1
[<ffffffff8142f343>] __mutex_lock_common+0x4b/0x383
[<ffffffff8142f73f>] mutex_lock_nested+0x3e/0x43
[<ffffffffa02ba5fc>] fcoe_create+0x27/0x4f7 [fcoe]
[<ffffffff810635b1>] param_attr_store+0x27/0x35
[<ffffffff81063619>] module_attr_store+0x26/0x2a
[<ffffffff8115dae3>] sysfs_write_file+0x108/0x144
[<ffffffff81107bd1>] vfs_write+0xae/0x10b
[<ffffffff81107cee>] sys_write+0x4a/0x6e
[<ffffffff81009b42>] system_call_fastpath+0x16/0x1b
other info that might help us debug this:
3 locks held by fcoemon/18823:
#0: (&buffer->mutex){+.+.+.}, at: [<ffffffff8115da17>]
sysfs_write_file+0x3c/0x144
#1: (s_active){++++.+}, at: [<ffffffff8115ef86>]
sysfs_get_active_two+0x24/0x48
#2: (s_active){++++.+}, at: [<ffffffff8115ef93>]
sysfs_get_active_two+0x31/0x48
stack backtrace:
Pid: 18823, comm: fcoemon Tainted: G W 2.6.33.1linux-stable-2.6.33 #1
Call Trace:
[<ffffffff81076c38>] print_circular_bug+0xa8/0xb6
[<ffffffff81077a85>] __lock_acquire+0xa1d/0xd2b
[<ffffffffa02ba5fc>] ? fcoe_create+0x27/0x4f7 [fcoe]
[<ffffffff81077e60>] lock_acquire+0xcd/0xf1
[<ffffffffa02ba5fc>] ? fcoe_create+0x27/0x4f7 [fcoe]
[<ffffffffa02ba5fc>] ? fcoe_create+0x27/0x4f7 [fcoe]
[<ffffffff8142f343>] __mutex_lock_common+0x4b/0x383
[<ffffffffa02ba5fc>] ? fcoe_create+0x27/0x4f7 [fcoe]
[<ffffffff8106ac70>] ? cpu_clock+0x43/0x5e
[<ffffffff81074e12>] ? lockstat_clock+0x11/0x13
[<ffffffff81074e40>] ? lock_release_holdtime+0x2c/0x127
[<ffffffff8115ef93>] ? sysfs_get_active_two+0x31/0x48
[<ffffffff8142f73f>] mutex_lock_nested+0x3e/0x43
[<ffffffffa02ba5fc>] fcoe_create+0x27/0x4f7 [fcoe]
[<ffffffff810635b1>] param_attr_store+0x27/0x35
[<ffffffff81063619>] module_attr_store+0x26/0x2a
[<ffffffff8115dae3>] sysfs_write_file+0x108/0x144
[<ffffffff81107bd1>] vfs_write+0xae/0x10b
[<ffffffff81076596>] ? trace_hardirqs_on_caller+0x125/0x150
[<ffffffff81107cee>] sys_write+0x4a/0x6e
[<ffffffff81009b42>] system_call_fastpath+0x16/0x1b
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch creates a port_id member in struct fc_lport.
This allows libfc to just deal with fc_lport instances
instead of calling into the fc_host to get the port_id.
This change helps in only using symbols necessary for
operation from the libfc structures. libfc still needs
to change the fc_host_port_id() if the port_id changes
so the presentation layer (scsi_transport_fc) can provide
the user with the correct value, but libfc shouldn't
rely on the presentation layer for operational values.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
It doesn't make sense to update the link speed in the is_link_ok()
routine. Move it to it's own routine and acquire the device speed
when we're configuring the device initially as well as if there are
any netdev events received.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The fcf pointer is checked again after this verification
making the first check redundant. Remote the first check.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
fcoe_create exits using out_nodev label when module is not
yet LIVE but this exit path unlocks the rtnl_lock though
rtnl lock was not held in this case.
So this patch replaces out_nodev with out_nomod to exit
w/o unlocking rtnl_lock.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Print all world wide node names (node, port and fabric) with the same
format specifier of "%16.16llx". That makes sure they all print as a
16 character hex string, with lower case letters, no 0x prefix, and
without stripping off any leading 0s.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
No reason to restrict CDB size to 12 bytes in fcoe, so
increased to 16 so that 16 bytes SCSI CDB doesn't fail.
Uses common define to set max_cmd_len for fcoe and fnic,
fnic is already setting max_cmd_len to 16.
sg_readcap -l fails without this fix.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Allow for dormant states while link configuration completes.
In the default link mode, this is equivalent to the old check.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The FIP controler state wasn't being reset on a disable.
A disable/enable sequence should be treated as a link event.
Otherwise, when using disable to mask a time when the link
is up but unusable, FCF discovery would attempt to continue
and login would jump directly to the non-FIP fallback on
enable.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FPMA indicates that the Fabric will provide the host's
N_Port's MAC address. When sending a FLOGI/FDISC frame
and FPMA was negotiated through FIP discovery we still
need to provide the MAC descriptor, as per the
specification, but the MAC should be zero'd out since
the FCF will be providing it in the FLOGI/FDISC ACC.
In FC-BB-5 section 7.8.7.4.2 (Fabric login) it states:
The MAC address field in the MAC address descriptor of a FIP FLOGI
Request operation or a FIP NPIV FDISC Request operation shall contain:
a) the proposed MAC address to use as VN_Port MAC address if the ENode
is requesting to use SPMA (see table 27);
b) all zeroes to indicate no MAC address is proposed if the ENode is
requesting to use FPMA (see table 27); or
c) the proposed MAC address to use as VN_Port MAC address if the ENode
supports both SPMA and FPMA and leaves the decision of which
addressing scheme to use to the FCF (i.e., if both the FP and SP
bits are set to one, see table 27).
This patch fixes case B.
This patch also adds debug statements to illustrate
whether a FPMA or SPMA MAC is added to a FLOGI/FDISC
frame.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When the kernel is configured for preemption, using smp_processor_id()
when preemption is enabled causes a warning backtrace and is wrong
since we could move off of that CPU as soon as we get the ID,
and we would be referencing the wrong CPU, and possibly an invalid one
if it could be hotswapped out.
Remove the fc_lport_get_stats() function and explicitly use per_cpu_ptr()
to get the statistics. Where preemption has been disabled by holding
a _bh lock continue to use smp_processor_id(), but otherwise use
get_cpu()/put_cpu().
In fcoe_recv_frame() also changed the cases where we return in the
middle to do a goto to the code which bumps ErrorFrames and does
a put_cpu(). Two of these cases didn't bump ErrorFrames before, but
doing so is harmless because they "can't happen", due to prior length
checks.
Also rearranged code in fcoe_recv_frame() to have only one call to
fc_exch_recv(). It's just as efficient and saves a call to put_cpu().
In fc_fcp.c, adjusted a FIXME comment for code which doesn't need fixing.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The link and last_link fields in the fcoe_ctlr struct are no
longer useful, since they are always set to the same value,
and FIP always calls libfc to pass link information to the lport.
Eliminate those fields and rename link_work to timer_work, since
it no longer has any link change work to do.
Thanks to Brian Uchino for discovering this issue.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove an unused variable, mac, in fcoe_recv_frame().
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In point-to-point mode, we need to save the source MAC
from received FLOGI requests to use as the destination MAC
for all outgoing frames. We stopped doing that at some point.
Use the lport_set_port_id method to catch incoming FLOGI frames
and pass them to fcoe_ctlr_recv_flogi() so it can save the source MAC.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The debug message that indicated we are using non-FIP mode was
being printed only if we were already in non-FIP mode.
Also changed the message text to make it more clear the mode
is being set, not that the message is indicating how FLOGI
was received.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In point-to-point mode, the destination MAC address for
the FLOGI response was zero because the LS_ACC for the FLOGI
wasn't getting intercepted by FIP.
Change to call fcoe_ctlr_els_send when sending any ELS,
not just requests.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
+little renaming of unicast functions to be smooth with multicast ones
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Currently we're gracefully tearing down each active connection
when fcoe.ko is removed. We shouldn't allow the user to destroy
connections by removing the module. We should force the user to
destroy each connection and then the module can be removed.
This patch makes it so a refrerence count on the module is taken
each time a fcoe_interface is created. The reference count
is dropped when the fcoe_interface is destroyed. This makes it
so that module_exit() doesn't get called unless all fcoe_interfaces
have been destroyed.
This patch leaves the removal of interfaces in the module_exit
routine so that if the user does a 'rmmod -f' we'll clean everything
up before removing the module.
The module_put line was put before the out_putdev goto line because
we should only be decrementing the reference count if a
fcoe_interface is actually destroyed. If we can't find the netdev
or the fcoe_interface then it's assumed that something else has
destroyed the fcoe_interface and it would have decremented the
reference count at that time.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
libfcoe module doesnt send port keep alive every
FIP_VN_KA_PERIOD due to improper assignment of timeout value.
Update the port_ka_time appropriately by incrementing it by
FIP_VN_KA_PERIOD in fcoe_ctlr_timeout(), so that the link_work
is scheduled to send the port LKA.
Signed-off-by: Bhanu Gollapudi <bprakash@broadcom.com>
Acked-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* 'cpumask-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
cpumask: rename tsk_cpumask to tsk_cpus_allowed
cpumask: don't recommend set_cpus_allowed hack in Documentation/cpu-hotplug.txt
cpumask: avoid dereferencing struct cpumask
cpumask: convert drivers/idle/i7300_idle.c to cpumask_var_t
cpumask: use modern cpumask style in drivers/scsi/fcoe/fcoe.c
cpumask: avoid deprecated function in mm/slab.c
cpumask: use cpu_online in kernel/perf_event.c
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: "James E.J. Bottomley" <James.Bottomley@suse.de>
Cc: Robert Love <robert.w.love@intel.com>
Cc: Chris Leech <christopher.leech@intel.com>
Cc: linux-scsi@vger.kernel.org
This is to allow fcoemon util to enable or disable a fcoe interface
according to DCB link state change.
Adds sysfs module param enable and disable for this and also
updates existing other module param description to be consistent
and more accurate since older description had double "fcoe" word
with less meaningful netdev reference to user space.
Adds code to ignore redundant fc_lport_enter_reset handling for a
already disabled fcoe interface by checking LPORT_ST_DISABLED
or LPORT_ST_LOGO states, this also prevents lport state transition
on link flap on a disabled interface.
Above changes required lport state transition to get out of
disabled or logo state on call to fc_fabric_login.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If the LLD wants its own WWNN/WWPN to be used, it should implement the
netdev_ops.ndo_fcoe_get_wwn(). If that is the case, we query the LLD and use
the queried WWNN/WWPN from the LLD.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add a member function pointer as get_lesb to libfc_function_template so LLD
can fill the LESB based on its own statistics. For fcoe, it fills the LESB
as a fcoe_fc_els_lesb struct according to FC-BB-5.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add tracking the Missing Discovery Advertisement count for FIP Fiber Channel
Forwarder (FCF) as described in FC-BB-5 Rev2.0 for LESB. The time is 1.5 times
the FKA_ADV_PERIOD of the corresponding FCF.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add tracking the Virtual Link Failure count when either we have found
the FCF as "aged" or we are receiving FIP Clear Virtual Link from the
FCF.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When the D bit is set if the FKA_ADV_Period of the FIP Discovery
Advertisement, the ENode should not transmit period ENode FIP Keep Alive and
VN_Port FIP Keep Alive (FC-BB-5 Rev2, 7.8.3.13).
Note that fcf->flags is taken directly from the fip_header, I am claiming one
bit for the purpose of the FIP_FKA_Period D bit as FIP_FL_FK_ADV_B, and use
FIP_HEADER_FLAGS as bitmask for bits used in fip_header.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Allow FCP frames to bypass the FCoE receive processing threads and handle
them directly in softirq context, if they are received on the correct CPU.
This preserves the queuing to threads for scaling out receive processing
to multiple CPUs, but allows FCoE-aware multi-queue network drivers that
direct frames to the originating CPUs to handle FCP processing with less
scheduling latency.
Only FCP is handled directly, because libfc makes use of mutexes in ELS
handling routines.
The bulk of this change is just moving the FCoE receive processing out of
the receive thread function, leaving behind just the thread and queue
management. The interesting bits are in fcoe_rcv()
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The FC-LS spec. says ELS timeouts should be 2 x R_A_TOV.
The FC-GS spec. says CT timeouts should be 3 x R_A_TOV.
We've been using E_D_TOV for both of those.
Change for all ELS and CT requests except FLOGI, which we
leave at 2 seconds (using E_D_TOV). One could argue that
R_A_TOV is locally determined until after FLOGI succeeds.
This does change FLOGI for vports which becomes FDISC.
This does not change the REC/SRR timeout which is 2 seconds.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
According to the FC-BB-5 Rev2.0, 7.8.6.2, we should not pad FIP keep-alive
frames.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
There are cases outside of our control that may result in a transmit
skb being linearized in dev_queue_xmit. There are a couple of bugs
in libfc/fcoe that can result in a panic at that point. This patch
contains two fixes to prevent those panics.
1) use fast cloning instead of shared skbs with dev_queue_xmit
dev_queue_xmit doen't want shared skbuffs being passed in, and
__skb_linearize will BUG if the skb is shared. FCoE is holding an extra
reference around the call to dev_queue_xmit, so that when it returns an
error code indicating the frame has been dropped it can maintain it's
own backlog and retransmit. Switch to using fast skb cloning for this
instead.
2) don't append compound pages as > PAGE_SIZE skb fragments
fc_fcp_send_data will append pages from a scatterlist to the nr_frags[]
if the netdev supports it. But, it's using > PAGE_SIZE compound pages
as a single skb_frag. In the highmem linearize case that page will be
passed to kmap_atomic to get a mapping to copy out of, but
kmap_atomic will only allow access to the first PAGE_SIZE part.
The memcpy will keep going and cause a page fault once is crosses the
first boundary.
If fc_fcp_send_data uses linear buffers from the start, it calls
kmap_atomic one PAGE_SIZE at a time. That same logic needs to be
applied when setting up skb_frags.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If the underlying netdev is a VLAN device, make sure the VLAN ID is integrated
into the WWNN/WWPN name generation. Also added/updated the comments to reflect
this change.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We are still using netdev->dev_addr to generate lport's WWNN/WWPN even if the
LLD has support for NETDEV_HW_ADDR_T_SAN. Instead, we should just use the
fip->ctl_src_addr, which is the NETDEV_HW_ADDR_T_SAN if LLD supports it or it
is just the netdev->dev_addr if it does not.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Make sure we are get the SAN MAC address from the real netdev if the input
netdev is a VLAN device.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This was fixed before in 7a7f0c7 but it's introduced again recently.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
There was a locking problem where the fip->lock was held during
the call to update_mac(). The rtnl_lock() must be taken before
the fip->lock, not the other way around. This fixes that.
Now that fcoe_ctlr_recv_flog() is called only from the response handler
to a FLOGI request, some checking can be eliminated. Instead of calling
update_mac(), just fill in the granted_mac address for the passed-in
frame (skb).
Eliminate the passed-in source MAC address since it is also in the skb.
Also, in fcoe, call fcoe_set_src_mac() directly instead of going thru
the fip function pointer. This will generate less code.
Then, since fip isn't needed for LOGO response, use lport as the arg.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch adds a check to fail gracefully when the netdevice
is bonded. Previously, the error was detected but the stack
would continue to load. This resulted in a partially enabled
fcoe intance and errors when the fcoe instance was destroy.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Remove the two extra function decalartions in fcoe.c.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If link is up, but no FCF is selected, don't send any ELS frames.
This came up when an fnic received a multicast advertisement but
no solitited advertisments, so no FCF was selected. It tried
to send FLOGIs anyway.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The fnic driver with FIP is reporting link up, even though it's down.
When the interface is shut down by the switch, we receive a clear
virtual link, and set the state reported to libfc as down, although
we still report it up. Clearly wrong. That causes the subsequent
link down event not to be reported, and /sys shows the host "Online".
Currently, in FIP mode, if an FCF times out, then link to libfc
is reported as down, to stop FLOGIs. That interferes with the LLD
link down being reported.
Users really need to know the physical link information, to diagnose
cabling issues, so physical link status should be reported to libfc.
If the selected FCF needs to be reported, that should be done
separately, in a later patch.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
FIP's fcoe_ctlr_recv() function was previously only called from
the soft IRQ in FCoE. It's not performance critical and is more
convenient for some drivers to call it from the IRQ level. Just
Change to use skb_queue()/dequeue() which uses spinlock_irqsave
instead of separate locking with _bh locks.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use scsi host number to identify debug messages.
Previously, no instance information was given, so if multiple
ports were active, it became confusing.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Allow FIP to be disabled by the driver for devices
that want to use libfcoe in non-FIP mode.
The driver merely sets the fcoe_ctlr mode to the state which
should be entered when the link comes up. The default is auto.
No change is needed for fcoe.c which uses auto mode.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added kernel-doc comment blocks to all structures and functions.
Renamed fc_lport instances rom lp to lport to be inline with our
naming convention.
Renamed all misnamed net_device instances to netdev to be inline
with our naming convention.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Ensures that there are kernel-doc style comments for all
routines and structures.
There were also a few instances of fc_lport's named 'lp'
which were switched to 'lport' as per the libfc/libfcoe/fcoe
naming convention.
Also, emacs 'indent-region' and 'tabify' were ran on libfcoe.c.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This is the Open-FCoE implementation of the FC
passthrough support via bsg interface.
Passthrough support is added to both N_Ports and
VN_Ports.
Signed-off-by: Steve Ma <steve.ma@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Allow a vport specific string to be appended to the port symbolic
name. The new symbolic name is sent to the name server after it
is set.
This currently messes with libhbalinux, which is looking for
the fcoe "fcoe <ver> over <ethX>" string and expects whatever
comes after the "over" to be a network interface name only.
Adds an EXPORT_SYMBOL to libfc for fc_frame_alloc_fill, which is
needed to allow fcoe to allocate a frame of variable length for
the RSPN request.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Vasu Dev