The current SocketCAN implementation for the Bosch c_can cell doesn't
account the TX bytes correctly, because it calls
c_can_inval_msg_object() (which clears the msg ctrl register) before
reading the DLC value:
for (/* nix */; (priv->tx_next - priv->tx_echo) > 0; priv->tx_echo++) {
msg_obj_no = get_tx_echo_msg_obj(priv);
c_can_inval_msg_object(dev, 0, msg_obj_no);
val = c_can_read_reg32(priv, &priv->regs->txrqst1);
if (!(val & (1 << msg_obj_no))) {
can_get_echo_skb(dev,
msg_obj_no - C_CAN_MSG_OBJ_TX_FIRST);
stats->tx_bytes += priv->read_reg(priv,
&priv->regs->ifregs[0].msg_cntrl)
& IF_MCONT_DLC_MASK;
stats->tx_packets++;
}
}
So, we will always read 0 for the DLC value and "ifconfig" will report
*0* TX Bytes.
The fix is quite easy: Just move c_can_inval_msg_object() to the end of
the if() statement. So:
* We only call c_can_inval_msg_object() if the message was
actually transmitted
* We read out the DLC value _before_ clearing the msg ctrl
register
Signed-off-by: Jan Altenberg <jan@linutronix.de>
Acked-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the check in the probe function whether a IRQ was supplied
to the driver. The original driver check the irq "struct resource *" against
<= 0. Use "platform_get_irq" instead.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch disables the one shot mode, until the driver has been fixed and
tested to support it.
> I'm quite sure I've seen a situation where msg_obj 17 "seemed" to be
> pending, while msg_obj 18 and 19 already have been transmitted. But
> in that case, I enabled ONESHOT for the can interface, which enables
> the DA mode (automatic retransmission is disabled).
Reported-by: Jan Altenberg <jan@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Cc: Bhupesh Sharma <bhupesh.sharma@st.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'irq-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tile: Use generic show_interupts()
tile: Convert to new irq function names
dma: Ipu: Convert interupt code
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator: Add MODULE_DEVICE_TABLE to max8997 and max8998
regulator: fix tps6524x section mismatch
regulator: Remove more wm831x-specific IRQ operations
regulator: add ab8500 enable and raise time delays
regulator: provide consumer interface for fall/rise time
regulator: add set_voltage_time_sel infrastructure
regulator: initialization for ab8500 regulators
regulator: add support for USB voltage regulator
regulator: switch the ab3100 to use enable_time()
Regulator: add suspend-finish API for regulator core.
regulator: fix typo in Kconfig
regulator: Convert WM831x regulators to genirq
regulator: If we fail when setting up a supply say which supply
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
staging: Fix bdops->check_events() misconversion in cyasblkdev_block.c
ide: ensure that we re-run the queue handler
* 'for-2.6.39/drivers' of git://git.kernel.dk/linux-2.6-block: (122 commits)
cciss: fix lost command issue
drbd: need include for bitops functions declarations
Revert "cciss: Add missing allocation in scsi_cmd_stack_setup and corresponding deallocation"
cciss: fix missed command status value CMD_UNABORTABLE
cciss: remove unnecessary casts
cciss: Mask off error bits of c->busaddr in cmd_special_free when calling pci_free_consistent
cciss: Inform controller we are using 32-bit tags.
cciss: hoist tag masking out of loop
cciss: Add missing allocation in scsi_cmd_stack_setup and corresponding deallocation
cciss: export resettable host attribute
drbd: drop code present under #ifdef which is relevant to 2.6.28 and below
drbd: Fixed handling of read errors on a 'VerifyS' node
drbd: Fixed handling of read errors on a 'VerifyT' node
drbd: Implemented real timeout checking for request processing time
drbd: Remove unused function atodb_endio()
drbd: improve log message if received sector offset exceeds local capacity
drbd: kill dead code
drbd: don't BUG_ON, if bio_add_page of a single page to an empty bio fails
drbd: Removed left over, now wrong comments
drbd: serialize admin requests for new verify run with pending bitmap io
...
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (f71882fg) Add support for the F71889A
hwmon: (f71882fg) Add support for the F81865F
hwmon: (f71882fg) Document all supported devices
hwmon: (f71882fg) Per-chip fan/temperature input count tables
hwmon: (f71882fg) Secure chip property definition arrays
The device table is required to load modules based on modaliases.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: MyungJoo Ham <myungjoo.ham@smasung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Use the combined irq_set_chip_and_handler() function
instead. Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
irq_desc checking in the interrupt demux routine is totally
pointless. The driver sets those lines up, so that cant go away
magically.
Remove the open coded handler magic and use the proper accessor.
This driver needs to be converted to threaded interrupts and buslock.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
irq_desc checking in a function which is called with that irq
descriptor locked, is pointless. Equally pointless as the irq desc
check in the interrupt service routine. The driver sets those lines
up, so that cant go away magically.
Remove the open coded handler magic and use the proper accessor.
No need to fiddle with irq_desc in the type setting function. The
original value is in irq_data and the core code stores the new setting
when the return value is 0.
This driver needs to be converted to threaded interrupts and buslock.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove the pointless irq_desc check in set_type. This function is
called with that irq descriptor locked. Also remove the write back of
the flow type as the core code does this already when the return value
is 0.
Also store the flow type in the chip data structure, so there is no
need to fiddle in the irq descriptor.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Replace the open coded handler call with the prober accessor. Retrieve
the handler data from desc. That avoids a redundant lookup in the
sparse irq case.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There is no point in checking irq_desc here, as it _is_ available. The
driver configured those lines, so they cannot go away.
The home brewn disabled/note_interrupt magic can be removed as well by
adding a irq_disable callback which avoids the lazy disable.
That driver needs to be converted to threaded interrupts.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove the open coded access to irq_desc and use the proper wrappers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The TPS61050/61052 driver uses MFD core code, yet does not specify the
dependency in Kconfig. If it is the only MFD driver configured, compilation
fails with
ERROR: "mfd_add_devices" [drivers/mfd/tps6105x.ko] undefined!
ERROR: "mfd_remove_devices" [drivers/mfd/tps6105x.ko] undefined!
Fix the problem by adding "select MFD_CORE" to the respective Kconfig entry.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The device table is required to load modules based on modaliases.
After adding MODULE_DEVICE_TABLE, below entry will be added to modules.pcimap:
rdc321x-southbridge 0x000017f3 0x00006030 0xffffffff 0xffffffff 0x00000000 0x00000000 0x0
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch enables IRQ handling for MAX8997/8966 chips.
Please note that Fuel-Gauge-related IRQs are not implemented in this
initial release. The fuel gauge module in MAX8997 is identical to
MAX17042, which is already in Linux kernel. In order to use the
already-existing MAX17042 driver for fuel gauge module in MAX8997, the
main interrupt handler of MAX8997 should relay related interrupts to
MAX17042 driver. However, in order to do this, we need to modify
MAX17042 driver as well because MAX17042 driver does not have any
interrupt handlers for now. We are not going to implement this in this
initial release as it is not crucial in basic operations of MAX8997.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Harald Welte <laforge@gnumonks.org>
Cc: Matti Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cs5535-pms cell doesn't actually need to be cloned, so we can drop that
and simply have the olpc-xo1.c driver use "cs5535-pms" directly.
Also, rename the cs5535-acpi clones to what we actually use for the (currently
out-of-tree) SCI driver. In the process, that fixes a subtle bug in
olpc-xo1.c which broke powerdown on XO-1s.. olpc-xo1-ac-acpi was a typo, not
something that actually existed.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Replace mfd_shared_platform_driver_register with mfd_clone_cell. The
former was called by an mfd client, and registered both a platform driver
and device. The latter is called by an mfd driver, and registers only a
platform device.
The downside of this is that mfd drivers need to be modified whenever
new clients are added that share a cell; the upside is that it fits
Linux's driver model better. It's also simpler.
This also converts cs5535-mfd/olpc-xo1 from the old API. cs5535-mfd
now creates the olpc-xo1-{acpi,pms} devices, while olpc-xo1 binds to
them via platform drivers.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Also add TMIO_BBS.
This allows these defines to also be used by zboot.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit cafb0bfca1 (staging: Convert to bdops->check_events())
incorrectly set bd->user_disk_0->events while initializing
bd->user_disk_1. Fix it.
The problem was spotted by Milton's suspect code pattern detector.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The conversion to blk_delay_queue() missed parts of IDE.
Add a blk_delay_queue() to ensure that the request handler
gets reinvoked when it needs to.
Note that in all but one place the old plug re-run delay of
3 msecs is used, even though it probably could be shorter
for performance reasons in some of those cases.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Commit 8677011 added auto-update to temperature limit registers.
Unfortunately, the update flag is also used to determine if an attribute
is writable, which results in read-only temperature limit registers.
To fix the problem, pass 'readonly' as separate flag to the function used
to add sensor attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix section mismatch that is caused by init code calling exit code:
pmic_remove() cannot be marked as __devexit.
WARNING: drivers/regulator/tps6524x-regulator.o(.devinit.text+0x205): Section mismatch in reference from the function pmic_probe() to the function .devexit.text:pmic_remove()
The function __devinit pmic_probe() references
a function __devexit pmic_remove().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __devexit annotation of
pmic_remove() so it may be used outside an exit section.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
These are the last users in the tree.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This uses the new infrastructure to provide proper delays when
enabling or setting the voltage of one specific regulator.
Cc: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This exposes the functionality for rise/fall fime when setting
voltage to the consumers.
Cc: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This makes it possible to set the stabilization time for voltage
regulators in the same manner as enable_time(). The interface
only supports regulators that implements fixed selectors.
Cc: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The regulators on the AB8500 have a lot of custom
hardware control settings pertaining to 8 external
signals, settings which are board-specific and need
be provided from the platform at startup.
Initialization added for regulators Vana, VextSupply1,
VextSupply2, VextSupply3, Vaux1, Vaux2, Vaux3, VTVout,
Vintcore12, Vaudio, Vdmic, Vamic1, Vamic2, VrefDDR.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This switches the ab3100 core to use the enable_time()
infrastructure from the regulator core.
Cc: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The regulator core had suspend-prepare that turns off the regulators
when entering a system-wide suspend. However, it did not have
suspend-finish that pairs with suspend-prepare and the regulator core
has assumed that the regulator devices and their drivers support
autonomous recover at resume.
This patch adds regulator_suspend_finish that pairs with the
previously-existed regulator_suspend_prepare. The function
regulator_suspend_finish turns on the regulators that have always_on set
or positive use_count so that we can reset the regulator states
appropriately at resume.
In regulator_suspend_finish, if has_full_constraints, it disables
unnecessary regulators.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
--
Updates
v3
comments corrected (Thanks to Igor)
v2
disable unnecessary regulators (Thanks to Mark)
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Fix typo: s/TPS695x0/TPS659x0/
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Makes it a bit easier to identify if it's a problem with the supplies,
the usual error would be omitting the supply name entirely.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the Fintek F81865F. It's essentially compatible with
the F71882FG, but has fewer inputs: 7 voltage, 2 temperature and 2 fan
inputs only.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
The list of supported devices was not always well documented in all
places. Clarify and list all devices in documentation, Kconfig and
the driver itself.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Use tables to list the count of fan and temperature inputs for all
supported chips, almost similar to (but more simple than) what is
already done for voltage inputs. This avoids repeating the same tests
in different functions, and will make it easier to add support for
chips with a different count of fan or temperature inputs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Using C99-style array initialization will ensure definitions won't
drift if the chips enum gets new values added.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
* 'syscore' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
Introduce ARCH_NO_SYSDEV_OPS config option (v2)
cpufreq: Use syscore_ops for boot CPU suspend/resume (v2)
KVM: Use syscore_ops instead of sysdev class and sysdev
PCI / Intel IOMMU: Use syscore_ops instead of sysdev class and sysdev
timekeeping: Use syscore_ops instead of sysdev class and sysdev
x86: Use syscore_ops instead of sysdev classes and sysdevs
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (55 commits)
[SCSI] tcm_loop: Add multi-fabric Linux/SCSI LLD fabric module
[SCSI] qla4xxx: Use polling mode for disable interrupt mailbox completion
[SCSI] Revert "[SCSI] Retrieve the Caching mode page"
[SCSI] bnx2fc: IO completion not processed due to missed wakeup
[SCSI] qla4xxx: Update driver version to 5.02.00-k6
[SCSI] qla4xxx: masking required bits of add_fw_options during initialization
[SCSI] qla4xxx: added new function qla4xxx_relogin_all_devices
[SCSI] qla4xxx: add support for ql4xsess_recovery_tmo cmd line param
[SCSI] qla4xxx: Add support for ql4xmaxqdepth command line parameter
[SCSI] qla4xxx: cleanup function qla4xxx_process_ddb_changed
[SCSI] qla4xxx: Prevent other port reinitialization during remove_adapter
[SCSI] qla4xxx: remove unused ddb flag DF_NO_RELOGIN
[SCSI] qla4xxx: cleanup DDB relogin logic during initialization
[SCSI] qla4xxx: Do not retry ISP82XX initialization if H/W state is failed
[SCSI] qla4xxx: Do not send mbox command if FW is in failed state
[SCSI] qla4xxx: cleanup qla4xxx_initialize_ddb_list()
[SCSI] ses: add subenclosure support
[SCSI] bnx2fc: Bump version to 1.0.1
[SCSI] bnx2fc: Remove unnecessary module state checks
[SCSI] bnx2fc: Fix MTU issue by using static MTU
...
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kdb: add usage string of 'per_cpu' command
kgdb,x86_64: fix compile warning found with sparse
kdb: code cleanup to use macro instead of value
kgdboc,kgdbts: strlen() doesn't count the terminator
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
route: Take the right src and dst addresses in ip_route_newports
ipv4: Fix nexthop caching wrt. scoping.
ipv4: Invalidate nexthop cache nh_saddr more correctly.
net: fix pch_gbe section mismatch warning
ipv4: fix fib metrics
mlx4_en: Removing HW info from ethtool -i report.
net_sched: fix THROTTLED/RUNNING race
drivers/net/a2065.c: Convert release_resource to release_region/release_mem_region
drivers/net/ariadne.c: Convert release_resource to release_region/release_mem_region
bonding: fix rx_handler locking
myri10ge: fix rmmod crash
mlx4_en: updated driver version to 1.5.4.1
mlx4_en: Using blue flame support
mlx4_core: reserve UARs for userspace consumers
mlx4_core: maintain available field in bitmap allocator
mlx4: Add blue flame support for kernel consumers
mlx4_en: Enabling new steering
mlx4: Add support for promiscuous mode in the new steering model.
mlx4: generalization of multicast steering.
mlx4_en: Reporting HW revision in ethtool -i
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: Disable ASPM when _OSC control is not granted for PCIe services
PCI: Changing ASPM policy, via /sys, to POWERSAVE could cause NMIs
PCI: PCIe links may not get configured for ASPM under POWERSAVE mode
PCI/ACPI: Report ASPM support to BIOS if not disabled from command line
* git://git.infradead.org/battery-2.6: (30 commits)
bq20z75: Fix time and temp units
bq20z75: Fix issues with present and suspend
z2_battery: Fix count of properties
s3c_adc_battery: Fix method names when PM not set
z2_battery: Add MODULE_DEVICE_TABLE
ds2782_battery: Add MODULE_DEVICE_TABLE
bq20z75: Add MODULE_DEVICE_TABLE
power_supply: Update power_supply_is_watt_property
bq20z75: Add i2c retry mechanism
bq20z75: Add optional battery detect gpio
twl4030_charger: Make the driver atomic notifier safe
bq27x00: Use single i2c_transfer call for property read
bq27x00: Cleanup bq27x00_i2c_read
bq27x00: Minor cleanups
bq27x00: Give more specific reports on battery status
bq27x00: Add MODULE_DEVICE_TABLE
bq27x00: Add new properties
bq27x00: Poll battery state
bq27x00: Cache battery registers
bq27x00: Add bq27000 support
...
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
dm stripe: implement merge method
dm mpath: allow table load with no priority groups
dm mpath: fail message ioctl if specified path is not valid
dm ioctl: add flag to wipe buffers for secure data
dm ioctl: prepare for crypt key wiping
dm crypt: wipe keys string immediately after key is set
dm: add flakey target
dm: fix opening log and cow devices for read only tables
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: tsc2005 - fix locking issue
Input: tsc2005 - use relative jiffies to schedule the watchdog
Input: tsc2005 - driver should depend on GENERIC_HARDIRQS
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] cmpxchg: implement cmpxchg64()
[S390] xchg/cmpxchg: move to own header file
[S390] ccwgroup_driver: remove duplicate members
[S390] ccw_bus_type: make it static
[S390] ccw_driver: remove duplicate members
[S390] qdio: prevent handling of buffers if count is zero
[S390] setup: register bss section as resource
[S390] setup: simplify setup_resources()
[S390] wire up sys_syncfs
[S390] wire up sys_clock_adjtime
[S390] wire up sys_open_by_handle_at
[S390] wire up sys_name_to_handle_at
[S390] oprofile: disable hw sampling for CONFIG_32BIT
[S390] early: limit savesys cmd string handling
[S390] early: Fix possible overlapping data buffer
This is an off by one because strlen() doesn't count the null
terminator. We strcpy() these strings into an array of size
MAX_CONFIG_LEN.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Convert to the new irq chip functions and cleanup the name space.
[ Guennadi reported: irq_data_get_chip_data is undefined. Yes, I screwed up.
it needs to be irq_data_get_irq_chip_data ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Dan Williams <dan.j.williams@intel.com>
LKML-Reference: <alpine.LFD.2.00.1103251220000.31464@localhost6.localdomain6>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6: (9356 commits)
[media] rc: update for bitop name changes
fs: simplify iget & friends
fs: pull inode->i_lock up out of writeback_single_inode
fs: rename inode_lock to inode_hash_lock
fs: move i_wb_list out from under inode_lock
fs: move i_sb_list out from under inode_lock
fs: remove inode_lock from iput_final and prune_icache
fs: Lock the inode LRU list separately
fs: factor inode disposal
fs: protect inode->i_state with inode->i_lock
lib, arch: add filter argument to show_mem and fix private implementations
SLUB: Write to per cpu data when allocating it
slub: Fix debugobjects with lockless fastpath
autofs4: Do not potentially dereference NULL pointer returned by fget() in autofs_dev_ioctl_setpipefd()
autofs4 - remove autofs4_lock
autofs4 - fix d_manage() return on rcu-walk
autofs4 - fix autofs4_expire_indirect() traversal
autofs4 - fix dentry leak in autofs4_expire_direct()
autofs4 - reinstate last used update on access
vfs - check non-mountpoint dentry might block in __follow_mount_rcu()
...
NOTE!
This merge commit was created to fix compilation error. The block
tree was merged upstream and removed the 'elv_queue_empty()'
function which the new 'mtdswap' driver is using. So a simple
merge of the mtd tree with upstream does not compile. And the
mtd tree has already be published, so re-basing it is not an option.
To fix this unfortunate situation, I had to merge upstream into the
mtd-2.6.git tree without committing, put the fixup patch on top of
this, and then commit this. The result is that we do not have commits
which do not compile.
In other words, this merge commit "merges" 3 things: the MTD tree, the
upstream tree, and the fixup patch.
Fix the following compilation warning:
drivers/mtd/mtdswap.c: In function ‘mtdswap_pick_gc_eblk’:
drivers/mtd/mtdswap.c:859: warning: ‘idx’ may be used uninitialized in this function
drivers/mtd/mtdswap.c:859: note: ‘idx’ was declared here
Initialize idx to -1 because this value means "no tree choosen".
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
As Artem Bityutskiy suggested: this option is controversial, as we
do not really have any prove it is useful. And it is too much to have
it as a config parameter. So, better kill it and let the real mtdswap
users decide whether it is needed or not.
Signed-off-by: Yang Ruirui<ruirui.r.yang@tieto.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The power-mode sequence on MMC is MMC_POWER_OFF -> MMC_POWER_UP ->
MMC_POWER_ON and not MMC_POWER_ON -> MMC_POWER_UP, as the driver currently
is implying.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
SDIO IRQs got unmasked on sh-mobile while writing to the
CTL_CLK_AND_WAIT_CTL register, because that register at address 0x138
is not implemented on those SoCs and writes to it overwrite the
register at address 0x38: CTL_SDIO_IRQ_MASK. Previous patches
eliminated access to register above 0xff on sh-mobile, so that this
work-around isn't needed anymore.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Not all tmio implementations have registers above oxff. Accessing
them on thise platforms is dangerous. In some cases it leads to
address wrapping to addresses below 0x100, which corrupts random
unrelated registers.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
On sh-mobile platforms the SDHI driver was using the tmio_mmc SD/SDIO
MFD cell driver. Now that the tmio_mmc driver has been split into a
core and a separate MFD glue, we can support SDHI natively without the
need to emulate an MFD controller. This also allows to support systems
with an on-SoC SDHI controller and a separate MFD with a TMIO core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
TMIO MMC chips contain an SD / SDIO IP core from Panasonic, similar to
the one, used in MN5774 and other MN57xx controllers. These IP cores are
included in many multifunction devices, in sh-mobile chips from Renesas,
in the latter case they can also use DMA. Some sh-mobile implementations
also have some other specialities, that MFD-based solutions don't have.
This makes supporting all these features in a monolithic driver inconveniet
and error-prone. This patch splits the driver into 3 parts: the core,
the MFD glue and the DMA support. In case of a modular build, two modules
will be built: mmc_tmio_core and mmc_tmio.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch allows transferring of some requests in PIO and some in DMA
mode and defaults to using DMA only for transfers longer than 8 bytes.
This is especially useful with SDIO, which can have lots of 2- and 4-byte
transfers, creating unnecessary high overhead, when executed in DMA.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
On some SDHI tmio implementations the order of DMA and command completion
interrupts swaps, which leads to malfunction. This patch postpones
DMA activation until the MMC command completion IRQ time.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch is based on the commit "af51715079e7fb6b290e1881d63d815dc4de5011":
* Bugfix to that mmc_send_cxd_data() code: dma-to-stack is
unsafe/nonportable, so kmalloc a bounce buffer instead.
The driver may invalidate the mmc_card->csd when host driver uses dma.
So this subroutine also needs a kmalloc buffer.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix the NO INT in the Multi-BLK IO in SD/MMC, and Multi-BLK read in
SDIO on imx53.
The CMDTYPE of the CMD register (offset 0xE) should be set to "11"
when the STOP CMD12 is issued on imx53 to abort one open ended
multi-blk IO. Otherwise the TC INT wouldn't be generated.
In exact block transfer, the controller doesn't complete the
operations automatically as required at the end of the transfer
and remains on hold if the abort command is not sent on imx53.
As a result, the TC flag is not asserted and SW receives timeout
exception. Set bit1 of Vendor Spec register to fix it.
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add one flag to indicate the GPIO CD/WP is enabled or not
on imx platforms, and reuse the writel/readl as the general
APIs for imx SOCs.
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add the abort CMDTYPE bits definition of command register (offset 0xE)
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sdhci-esdhc-imx does not need SDHCI_QUIRK_NO_CARD_NO_RESET.
Make it OF-specific.
Signed-off-by: Richard Zhu <Hong-Xing.Zhu@freescale.com>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since these are the headers that provide irq_of_parse_and_map()
and NO_IRQ.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Chris Ball <cjb@laptop.org>
New IO FPGA implementation for Versatile Express boards contain
MMCI (PL180) cell with FIFO extended to 128 words (512 bytes).
Matt Waddel reports that this patch improves MMC performance on
his vexpress system, and also fixes "mmcblk0: error -5 transferring
data" errors.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Tested-by: Matt Waddel <matt.waddel@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch uses the fixed burst bit when using an internal DMA controller.
I found increased performance with IDMAC when this bit is set.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The SDHCI driver uses PCI_CLASS_REVISION instead of PCI_REVISION_ID, so
it was not converted by commit 44c10138fd
(PCI: Change all drivers to use pci_device->revision). The newer VIA
driver has similar code too. This patch converts both drivers to use
the 'revision' field of 'struct pci_dev'.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fixes:
drivers/mmc/card/mmc_test.c: In function ‘mmc_test_seq_perf’:
drivers/mmc/card/mmc_test.c:1878:28: warning: variable ‘ts’ set but not
used [-Wunused-but-set-variable]
There's no reason to be calling timespec_sub() here, because
mmc_test_print_avg_rate() is going to do that itself.
Signed-off-by: Chris Ball <cjb@laptop.org>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Fix the following compile failure:
drivers/media/rc/ite-cir.c: In function 'ite_decode_bytes':
drivers/media/rc/ite-cir.c:190: error: implicit declaration of function 'generic_find_next_le_bit'
drivers/media/rc/ite-cir.c:199: error: implicit declaration of function 'generic_find_next_zero_le_bit'
Caused by commit 620a32bba4 ("[media] rc: New rc-based ite-cir driver
for several ITE CIRs") interacting with commit c4945b9ed4
("asm-generic: rename generic little-endian bitops functions").
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit ddd588b5dd ("oom: suppress nodes that are not allowed from
meminfo on oom kill") moved lib/show_mem.o out of lib/lib.a, which
resulted in build warnings on all architectures that implement their own
versions of show_mem():
lib/lib.a(show_mem.o): In function `show_mem':
show_mem.c:(.text+0x1f4): multiple definition of `show_mem'
arch/sparc/mm/built-in.o:(.text+0xd70): first defined here
The fix is to remove __show_mem() and add its argument to show_mem() in
all implementations to prevent this breakage.
Architectures that implement their own show_mem() actually don't do
anything with the argument yet, but they could be made to filter nodes
that aren't allowed in the current context in the future just like the
generic implementation.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: James Bottomley <James.Bottomley@hansenpartnership.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/vblank: update recently added vbl interface to be more future proof.
drm radeon: Return -EINVAL on wrong pm sysfs access
drm/radeon/kms: fix hardcoded EDID handling
Revert "drm/i915: Don't save/restore hardware status page address register"
drm/i915: Avoid unmapping pages from a NULL address space
drm/i915: Fix use after free within tracepoint
drm/i915: Restore missing command flush before interrupt on BLT ring
drm/i915: Disable pagefaults along execbuffer relocation fast path
drm/i915: Fix computation of pitch for dumb bo creator
drm/i915: report correct render clock frequencies on SNB
drm/i915/dp: Correct the order of deletion for ghost eDP devices
drm/i915: Fix tiling corruption from pipelined fencing
drm/i915: Re-enable self-refresh
drm/i915: Prevent racy removal of request from client list
drm/i915: skip redundant operations whilst enabling pipes and planes
drm/i915: Remove surplus POSTING_READs before wait_for_vblank
drm/radeon/kms: prefer legacy pll algo for tv-out
drm: check for modesetting on modeset ioctls
drm/kernel: vblank wait on crtc > 1
drm: Fix use-after-free in drm_gem_vm_close()
Commit 1765a57533 ("net: make dev->master general") introduced a
test of an uninitialized netdev. Fix the code so the intended netdev
is tested.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix section mismatch warning by renaming the pci_driver variable to a
recognized (whitelisted) name.
WARNING: drivers/net/pch_gbe/pch_gbe.o(.data+0x1f8): Section mismatch in reference from the variable pch_gbe_pcidev to the variable .devinit.rodata:pch_gbe_pcidev_id
The variable pch_gbe_pcidev references
the variable __devinitconst pch_gbe_pcidev_id
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
LKML-Reference: <20110324212509.118888535@linutronix.de>
Converted with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
LKML-Reference: <20110324212509.025730689@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
gpiolib plus two gpio implementations in arm fiddle in the guts of
irq_desc in a racy and buggy way. Remove the stuff. I already told the
gpio folks that we can provide that information in a proper way if
necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
LKML-Reference: <20110324212508.931638262@linutronix.de>
Avoiding abuse of ethtool_drvinfo.driver field.
HW specific info can be retrieved using lspci.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-2.6.39/core' of git://git.kernel.dk/linux-2.6-block: (65 commits)
Documentation/iostats.txt: bit-size reference etc.
cfq-iosched: removing unnecessary think time checking
cfq-iosched: Don't clear queue stats when preempt.
blk-throttle: Reset group slice when limits are changed
blk-cgroup: Only give unaccounted_time under debug
cfq-iosched: Don't set active queue in preempt
block: fix non-atomic access to genhd inflight structures
block: attempt to merge with existing requests on plug flush
block: NULL dereference on error path in __blkdev_get()
cfq-iosched: Don't update group weights when on service tree
fs: assign sb->s_bdi to default_backing_dev_info if the bdi is going away
block: Require subsystems to explicitly allocate bio_set integrity mempool
jbd2: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
jbd: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
fs: make fsync_buffers_list() plug
mm: make generic_writepages() use plugging
blk-cgroup: Add unaccounted time to timeslice_used.
block: fixup plugging stubs for !CONFIG_BLOCK
block: remove obsolete comments for blkdev_issue_zeroout.
blktrace: Use rq->cmd_flags directly in blk_add_trace_rq.
...
Fix up conflicts in fs/{aio.c,super.c}
* 'usb-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: cdc-acm: fix potential null-pointer dereference on disconnect
USB: cdc-acm: fix potential null-pointer dereference
USB: cdc-acm: fix memory corruption / panic
USB: Fix 'bad dma' problem on WDM device disconnect
usb: wwan: fix compilation without CONFIG_PM_RUNTIME
USB: uss720 fixup refcount position
usb: musb: blackfin: fix typo in new bfin_musb_vbus_status func
usb: musb: blackfin: fix typo in new dev_pm_ops struct
usb: musb: blackfin: fix typo in platform driver name
usb: musb: Fix for merge issue
ehci-hcd: Bug fix: don't set a QH's Halt bit
USB: Do not pass negative length to snoop_urb()
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (442 commits)
[media] videobuf2-dma-contig: make cookie() return a pointer to dma_addr_t
[media] sh_mobile_ceu_camera: Do not call vb2's mem_ops directly
[media] V4L: soc-camera: explicitly require V4L2_BUF_TYPE_VIDEO_CAPTURE
[media] v4l: soc-camera: Store negotiated buffer settings
[media] rc: interim support for 32-bit NEC-ish scancodes
[media] mceusb: topseed 0x0011 needs gen3 init for tx to work
[media] lirc_zilog: error out if buffer read bytes != chunk size
[media] lirc: silence some compile warnings
[media] hdpvr: use same polling interval as other OS
[media] ir-kbd-i2c: pass device code w/key in hauppauge case
[media] rc/keymaps: Remove the obsolete rc-rc5-tv keymap
[media] remove the old RC_MAP_HAUPPAUGE_NEW RC map
[media] rc/keymaps: Rename Hauppauge table as rc-hauppauge
[media] rc-rc5-hauppauge-new: Fix Hauppauge Grey mapping
[media] rc-rc5-hauppauge-new: Add support for the old Black RC
[media] rc-rc5-hauppauge-new: Add the old control to the table
[media] rc-winfast: Fix the keycode tables
[media] a800: Fix a few wrong IR key assignments
[media] opera1: Use multimedia keys instead of an app-specific mapping
[media] dw2102: Use multimedia keys instead of an app-specific mapping
...
Fix up trivial conflicts (remove/modify and some real conflicts) in:
arch/arm/mach-omap2/devices.c
drivers/staging/Kconfig
drivers/staging/Makefile
drivers/staging/dabusb/dabusb.c
drivers/staging/dabusb/dabusb.h
drivers/staging/easycap/easycap_ioctl.c
drivers/staging/usbvideo/usbvideo.c
drivers/staging/usbvideo/vicam.c
* 'devicetree/merge' of git://git.secretlab.ca/git/linux-2.6:
spi/pl022: Add loopback support for the SPI on 5500
spi/omap_mcspi: Fix broken last word xfer
of/flattree: minor cleanups
dt: eliminate OF_NO_DEEP_PROBE and test for NULL match table
dt: protect against NULL matches passed to of_match_node()
dt: Refactor of_platform_bus_probe()
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (42 commits)
ACPI: minor printk format change in acpi_pad
ACPI: make acpi_pad /sys output more readable
ACPICA: Update version to 20110316
ACPICA: Header support for SLIC table
ACPI: Make sure the FADT is at least rev 2 before using the reset register
ACPI: Bug compatibility for Windows on the ACPI reboot vector
ACPICA: Fix access width for reset vector
ACPI battery: fribble sysfs files from a resume notifier
ACPI button: remove unused procfs I/F
ACPI, APEI, Add PCIe AER error information printing support
PCIe, AER, use pre-generated prefix in error information printing
ACPI, APEI, Add ERST record ID cache
ACPI: Use syscore_ops instead of sysdev class and sysdev
ACPI: Remove the unused EC sysdev class
ACPI: use __cpuinit for the acpi_processor_set_pdc() call tree
ACPI: use __init where possible in processor driver
Thermal_Framework-Fix_crash_during_hwmon_unregister
ACPICA: Update version to 20110211.
ACPICA: Add mechanism to defer _REG methods for some installed handlers
ACPICA: Add support for FunctionalFixedHW in acpi_ut_get_region_name
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB: Increase DMA max_segment_size on Mellanox hardware
IB/mad: Improve an error message so error code is included
RDMA/nes: Don't print success message at level KERN_ERR
RDMA/addr: Fix return of uninitialized ret value
IB/srp: try to use larger FMR sizes to cover our mappings
IB/srp: add support for indirect tables that don't fit in SRP_CMD
IB/srp: rework mapping engine to use multiple FMR entries
IB/srp: allow sg_tablesize to be set for each target
IB/srp: move IB CM setup completion into its own function
IB/srp: always avoid non-zero offsets into an FMR
We should unlock here and also decrement the number of &map->users.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
copy_to_user() returns the amount of data remaining to be copied. We
want to return a negative error code here. The upper layers just
call WARN_ON() if we return non-zero so this doesn't change the
behavior. But returning -EFAULT is still cleaner.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This patch fixes a brown-paperbag bug which was introduced by me:
I used incorrect "GFP_KERNEL | GFP_NOFS" allocation flags to make
sure my allocations do not cause write-back. But the correct form
is "GFP_NOFS".
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Implement a merge function in the striped target.
When the striped target's underlying devices provide a merge_bvec_fn
(like all DM devices do via dm_merge_bvec) it is important to call down
to them when building a biovec that doesn't span a stripe boundary.
Without the merge method, a striped DM device stacked on DM devices
causes bios with a single page to be submitted which results
in unnecessary overhead that hurts performance.
This change really helps filesystems (e.g. XFS and now ext4) which take
care to assemble larger bios. By implementing stripe_merge(), DM and the
stripe target no longer undermine the filesystem's work by only allowing
a single page per bio. Buffered IO sees the biggest improvement
(particularly uncached reads, buffered writes to a lesser degree). This
is especially so for more capable "enterprise" storage LUNs.
The performance improvement has been measured to be ~12-35% -- when a
reasonable chunk_size is used (e.g. 64K) in conjunction with a stripe
count that is a power of 2.
In contrast, the performance penalty is ~5-7% for the pathological worst
case stripe configuration (small chunk_size with a stripe count that is
not a power of 2). The reason for this is that stripe_map_sector() is
now called once for every call to dm_merge_bvec(). stripe_map_sector()
will use slower division if stripe count isn't a power of 2.
Signed-off-by: Mustafa Mesanovic <mume@linux.vnet.ibm.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch adjusts the multipath target to allow a table with both 0
priority groups and 0 for the initial priority group number.
If any mpath device is held open when all paths in the last priority
group have failed, userspace multipathd will attempt to reload the
associated DM table to reflect the fact that the device no longer has
any priority groups. But the reload attempt always failed because the
multipath target did not allow 0 priority groups.
All multipath target messages related to priority group (enable_group,
disable_group, switch_group) will handle a priority group of 0 (will
cause error).
When reloading a multipath table with 0 priority groups, userspace
multipathd must be updated to specify an initial priority group number
of 0 (rather than 1).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Babu Moger <babu.moger@lsi.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fail the reinstate_path and fail_path message ioctl if the specified
path is not valid.
The message ioctl would succeed for the 'reinistate_path' and
'fail_path' messages even if action was not taken because the
specified device was not a valid path of the multipath device.
Before, when /dev/vdb is not a path of mpathb:
$ dmsetup message mpathb 0 reinstate_path /dev/vdb
$ echo $?
0
After:
$ dmsetup message mpathb 0 reinstate_path /dev/vdb
device-mapper: message ioctl failed: Invalid argument
Command failed
$ echo $?
1
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add DM_SECURE_DATA_FLAG which userspace can use to ensure
that all buffers allocated for dm-ioctl are wiped
immediately after use.
The user buffer is wiped as well (we do not want to keep
and return sensitive data back to userspace if the flag is set).
Wiping is useful for cryptsetup to ensure that the key
is present in memory only in defined places and only
for the time needed.
(For crypt, key can be present in table during load or table
status, wait and message commands).
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Prepare code for implementing buffer wipe flag.
No functional change in this patch.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Always wipe the original copy of the key after processing it
in crypt_set_key().
Signed-off-by: Milan Broz <mbroz@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This target is the same as the linear target except that it returns I/O
errors periodically. It's been found useful in simulating failing
devices for testing purposes.
I needed a dm target to do some failure testing on btrfs's raid code, and
Mike pointed me at this.
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If a table is read-only, also open any log and cow devices it uses read-only.
Previously, even read-only devices were opened read-write internally.
After patch 75f1dc0d07
block: check bdev_read_only() from blkdev_get()
was applied, loading such tables began to fail. The patch
was reverted by e51900f7d3
block: revert block_dev read-only check
but this patch fixes this part of the code to work with the original patch.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This makes the interface a bit cleaner by leaving a single gap in the
vblank bit space instead of creating two gaps.
Suggestions from Michel on mailing list/irc.
Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Throw an error if someone tries to fill this with
wrong data, instead of simply ignoring the input.
Now you get:
echo hello >/sys/../power_method
-bash: echo: write error: Invalid argument
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: Alexander.Deucher@amd.com
CC: dri-devel@lists.freedesktop.org
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On some servers there is a hardcoded EDID provided
in the vbios so that the driver will always see a
display connected even if something like a KVM
prevents traditional means like DDC or load
detection from working properly. Also most
server boards with DVI are not actually DVI, but
DVO connected to a virtual KVM service processor.
If we fail to detect a monitor via DDC or load
detection and a hardcoded EDID is available, use
it.
Additionally, when using the hardcoded EDID, use
a copy of it rather than the actual one stored
in the driver as the detect() and get_modes()
functions may free it if DDC is successful.
This fixes the virtual KVM on several internal
servers.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-fixes' of ../drm-next:
Revert "drm/i915: Don't save/restore hardware status page address register"
drm/i915: Avoid unmapping pages from a NULL address space
drm/i915: Fix use after free within tracepoint
drm/i915: Restore missing command flush before interrupt on BLT ring
drm/i915: Disable pagefaults along execbuffer relocation fast path
drm/i915: Fix computation of pitch for dumb bo creator
drm/i915: report correct render clock frequencies on SNB
drm/i915/dp: Correct the order of deletion for ghost eDP devices
drm/i915: Fix tiling corruption from pipelined fencing
drm/i915: Re-enable self-refresh
drm/i915: Prevent racy removal of request from client list
drm/i915: skip redundant operations whilst enabling pipes and planes
drm/i915: Remove surplus POSTING_READs before wait_for_vblank
This reverts commit a7a75c8f70.
There are two different variations on how Intel hardware addresses the
"Hardware Status Page". One as a location in physical memory and the
other as an offset into the virtual memory of the GPU, used in more
recent chipsets. (The HWS itself is a cacheable region of memory which
the GPU can write to without requiring CPU synchronisation, used for
updating various details of hardware state, such as the position of
the GPU head in the ringbuffer, the last breadcrumb seqno, etc).
These two types of addresses were updated in different locations of code
- one inline with the ringbuffer initialisation, and the other during
device initialisation. (The HWS page is logically associated with
the rings, and there is one HWS page per ring.) During resume, only the
ringbuffers were being re-initialised along with the virtual HWS page,
leaving the older physical address HWS untouched. This then caused a
hang on the older gen3/4 (915GM, 945GM, 965GM) the first time we tried
to synchronise the GPU as the breadcrumbs were never being updated.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Jan Niehusmann <jan@gondor.com>
Reported-and-tested-by: Justin P. Mattock <justinmattock@gmail.com>
Reported-and-tested-by: Michael "brot" Groh <brot@minad.de>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Commit 0b950d3 (Input: tsc2005 - add open/close) introduced a
locking issue with the ESD watchdog: __tsc2005_disable() is calling
cancel_delayed_work_sync() with mutex held, and the work also needs the
same mutex.
Fix the problem by using mutex_trylock() in tsc2005_esd_work(). If the
mutex is taken, we know we are in the middle of disable or enable and
the watchdog check can be skipped.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use relative jiffies to schedule the watchdog. Otherwise it will run
like a mad one.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
drivers/input/touchscreen/tsc2005.c: In function ‘tsc2005_probe’:
drivers/input/touchscreen/tsc2005.c:666: error: implicit declaration of function ‘set_irq_wake’
In addition, migrate from set_irq_wake() (marked "do not use" as of commit
a0cd9ca2b9 ("genirq: Namespace cleanup")) to
irq_set_irq_wake().
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (35 commits)
ARM: Update (and cut down) mach-types
ARM: 6771/1: vexpress: add support for multiple core tiles
ARM: 6797/1: hw_breakpoint: Fix newlines in WARNings
ARM: 6751/1: vexpress: select applicable errata workarounds in Kconfig
ARM: 6753/1: omap4: Enable ARM local timers with OMAP4430 es1.0 exception
ARM: 6759/1: smp: Select local timers vs broadcast timer support runtime
ARM: pgtable: add pud-level code
ARM: 6673/1: LPAE: use phys_addr_t instead of unsigned long for start of membanks
ARM: Use long long format when printing meminfo physical addresses
ARM: integrator: add Integrator/CP sched_clock support
ARM: realview/vexpress: consolidate SMP bringup code
ARM: realview/vexpress: consolidate localtimer support
ARM: integrator/versatile: consolidate FPGA IRQ handling code
ARM: rationalize versatile family Kconfig/Makefile
ARM: realview: remove old AMBA device DMA definitions
ARM: versatile: remove old AMBA device DMA definitions
ARM: vexpress: use new init_early for clock tree and sched_clock init
ARM: realview: use new init_early for clock tree and sched_clock init
ARM: versatile: use new init_early for clock tree and sched_clock init
ARM: integrator: use new init_early for clock tree init
...
Extend the vendor data with a loopback field, and add new
amba-pl022 vendor data for the DB5500 pl023, as the pl023
on db8500 and db5500 vary.
Signed-off-by: Prajadevi H <prajadevi.h@stericsson.com>
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
- Introduce ns_capable to test for a capability in a non-default
user namespace.
- Teach cap_capable to handle capabilities in a non-default
user namespace.
The motivation is to get to the unprivileged creation of new
namespaces. It looks like this gets us 90% of the way there, with
only potential uid confusion issues left.
I still need to handle getting all caps after creation but otherwise I
think I have a good starter patch that achieves all of your goals.
Changelog:
11/05/2010: [serge] add apparmor
12/14/2010: [serge] fix capabilities to created user namespaces
Without this, if user serge creates a user_ns, he won't have
capabilities to the user_ns he created. THis is because we
were first checking whether his effective caps had the caps
he needed and returning -EPERM if not, and THEN checking whether
he was the creator. Reverse those checks.
12/16/2010: [serge] security_real_capable needs ns argument in !security case
01/11/2011: [serge] add task_ns_capable helper
01/11/2011: [serge] add nsown_capable() helper per Bastian Blank suggestion
02/16/2011: [serge] fix a logic bug: the root user is always creator of
init_user_ns, but should not always have capabilities to
it! Fix the check in cap_capable().
02/21/2011: Add the required user_ns parameter to security_capable,
fixing a compile failure.
02/23/2011: Convert some macros to functions as per akpm comments. Some
couldn't be converted because we can't easily forward-declare
them (they are inline if !SECURITY, extern if SECURITY). Add
a current_user_ns function so we can use it in capability.h
without #including cred.h. Move all forward declarations
together to the top of the #ifdef __KERNEL__ section, and use
kernel-doc format.
02/23/2011: Per dhowells, clean up comment in cap_capable().
02/23/2011: Per akpm, remove unreachable 'return -EPERM' in cap_capable.
(Original written and signed off by Eric; latest, modified version
acked by him)
[akpm@linux-foundation.org: fix build]
[akpm@linux-foundation.org: export current_user_ns() for ecryptfs]
[serge.hallyn@canonical.com: remove unneeded extra argument in selinux's task_has_capability]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Daniel Lezcano <daniel.lezcano@free.fr>
Acked-by: David Howells <dhowells@redhat.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If rio is not a switch then "rswitch" is null.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removes resource reservation from the common sybsystem initialization code
and make it part of mport driver initialization. This resolves conflict
with resource reservation by device specific mport drivers.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changes mport ID and host destination ID assignment to implement unified
method common to all mport drivers. Makes "riohdid=" kernel command line
parameter common for all architectures with support for more that one host
destination ID assignment.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Subsystem initialization sequence modified to support presence of multiple
RapidIO controllers in the system. The new sequence is compatible with
initialization of PCI devices.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. Add an option to include RapidIO support if the PCI is available.
2. Add FSL_RIO configuration option to enable controller selection.
3. Add RapidIO support option into x86 and MIPS architectures.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This set of patches eliminates RapidIO dependency on PowerPC architecture
and makes it available to other architectures (x86 and MIPS). It also
enables support of new platform independent RapidIO controllers such as
PCI-to-SRIO and PCI Express-to-SRIO.
This patch:
Extend number of mport callback functions to eliminate direct linking of
architecture specific mport operations.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add new sysfs attributes.
1. Routing information required to to reach the RIO device:
destid - device destination ID (real for for endpoint, route for switch)
hopcount - hopcount for maintenance requests (switches only)
2. device linking information:
lprev - name of device that precedes the given device in the enumeration
or discovery order (displayed along with of the port to which it
is attached).
lnext - names of devices (with corresponding port numbers) that are
attached to the given device as next in the enumeration or
discovery order (switches only)
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Thomas Moll <thomas.moll@sysgo.com>
Cc: Micha Nelissen <micha@neli.hopto.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reduce the lines of code and simplify the logic.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert calls to func_enter on leaving a function to func_exit.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- func_enter();
+ func_exit();
return...;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Roger Wolff <R.E.Wolff@BitWizard.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
put_tty_driver calls tty_driver_kref_put on its argument, and then
tty_driver_kref_put calls kref_put on the address of a field of this
argument. kref_put checks for NULL, but in this case the field is likely
to have some offset and so the result of taking its address will not be
NULL. Labels are added to be able to skip over the call to put_tty_driver
when the argument will be NULL.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
@@
*if (x == NULL)
{ ...
* put_tty_driver(x);
...
return ...;
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Torben Hohn <torbenh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As a preparation for removing ext2 non-atomic bit operations from
asm/bitops.h. This converts ext2 non-atomic bit operations to
little-endian bit operations.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Alasdair Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As a preparation for removing ext2 non-atomic bit operations from
asm/bitops.h. This converts ext2 non-atomic bit operations to
little-endian bit operations.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit a7a75c8f70.
There are two different variations on how Intel hardware addresses the
"Hardware Status Page". One as a location in physical memory and the
other as an offset into the virtual memory of the GPU, used in more
recent chipsets. (The HWS itself is a cacheable region of memory which
the GPU can write to without requiring CPU synchronisation, used for
updating various details of hardware state, such as the position of
the GPU head in the ringbuffer, the last breadcrumb seqno, etc).
These two types of addresses were updated in different locations of code
- one inline with the ringbuffer initialisation, and the other during
device initialisation. (The HWS page is logically associated with
the rings, and there is one HWS page per ring.) During resume, only the
ringbuffers were being re-initialised along with the virtual HWS page,
leaving the older physical address HWS untouched. This then caused a
hang on the older gen3/4 (915GM, 945GM, 965GM) the first time we tried
to synchronise the GPU as the breadcrumbs were never being updated.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Jan Niehusmann <jan@gondor.com>
Reported-by: Justin P. Mattock <justinmattock@gmail.com>
Reported-and-tested-by: Michael "brot" Groh <brot@minad.de>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce Kconfig option allowing architectures where sysdev
operations used during system suspend, resume and shutdown have been
completely replaced with struct sycore_ops operations to avoid
building sysdev code that will never be used.
Make callbacks in struct sys_device and struct sysdev_driver depend
on ARCH_NO_SYSDEV_OPS to allows us to verify if all of the references
have been actually removed from the code the given architecture
depends on.
Make x86 select ARCH_NO_SYSDEV_OPS.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The cpufreq subsystem uses sysdev suspend and resume for
executing cpufreq_suspend() and cpufreq_resume(), respectively,
during system suspend, after interrupts have been switched off on the
boot CPU, and during system resume, while interrupts are still off on
the boot CPU. In both cases the other CPUs are off-line at the
relevant point (either they have been switched off via CPU hotplug
during suspend, or they haven't been switched on yet during resume).
For this reason, although it may seem that cpufreq_suspend() and
cpufreq_resume() are executed for all CPUs in the system, they are
only called for the boot CPU in fact, which is quite confusing.
To remove the confusion and to prepare for elimiating sysdev
suspend and resume operations from the kernel enirely, convernt
cpufreq to using a struct syscore_ops object for the boot CPU
suspend and resume and rename the callbacks so that their names
reflect their purpose. In addition, put some explanatory remarks
into their kerneldoc comments.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The Intel IOMMU subsystem uses a sysdev class and a sysdev for
executing iommu_suspend() after interrupts have been turned off
on the boot CPU (during system suspend) and for executing
iommu_resume() before turning on interrupts on the boot CPU
(during system resume). However, since both of these functions
ignore their arguments, the entire mechanism may be replaced with a
struct syscore_ops object which is simpler.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Request_mem_region should be used with release_mem_region, not
release_resource.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,E;
@@
*x = request_mem_region(...)
... when != release_mem_region(x)
when != x = E
* release_resource(x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Request_mem_region should be used with release_mem_region, not
release_resource.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,E;
@@
*x = request_mem_region(...)
... when != release_mem_region(x)
when != x = E
* release_resource(x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit adef658 "spi/omap_mcspi: catch xfers of non-multiple SPI word size"
broke the transmission of last word in cases where access is multiple of
word size and word size is 16 or 32 bits.
Fix this by replacing the test "c > (word_len>>3)" in do-while loops with
"c >= 'pointer increment size'". This ensures that the last word is
transmitted in above case and still allow to break the loop and prevent
variable c underflow in cases where word size != 'pointer increment size'.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Tested-by: Sourav Poddar<sourav.poddar@ti.com>
Acked-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
- static-ize some functions
- add some additional comments
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There are no users of OF_NO_DEEP_PROBE, and of_match_node() now
gracefully handles being passed a NULL pointer, so the checks at the
top of of_platform_bus_probe can be dropped.
While at it, consolidate the root node pointer check to be easier to
read and tidy up related comments.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There are a few use cases where it is convenient to pass NULL to
of_match_node() and have it fail gracefully. The patch adds a null
check to the beginning so taht it does so.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The current implementation uses three copies of of basically identical
code. This patch consolidates them to make the code simpler.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix potential null-pointer exception on disconnect introduced by commit
11ea859d64 (USB: additional power savings
for cdc-acm devices that support remote wakeup).
Only access acm->dev after making sure it is non-null in control urb
completion handler.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Must check return value of tty_port_tty_get.
Cc: stable <stable@kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the WDM class driver a disconnect event leads to calls to
usb_free_coherent to put back two USB DMA buffers allocated earlier.
The call to usb_free_coherent uses a different size parameter
(desc->wMaxCommand) than the corresponding call to usb_alloc_coherent
(desc->bMaxPacketSize0).
When a disconnect event occurs, this leads to 'bad dma' complaints
from usb core because the USB DMA buffer is being pushed back to the
'buffer-2048' pool from which it has not been allocated.
This patch against the most recent linux-2.6 kernel ensures that the
parameters used by usb_alloc_coherent & usb_free_coherent calls in
cdc-wdm.c match.
Signed-off-by: Robert Lukassen <robert.lukassen@tomtom.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pm usage counter must be accessed with the proper wrappers
to allow compilation under all configurations.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My testprog do a lot of bitbang - after hours i got following warning and my machine lockups:
WARNING: at /build/buildd/linux-2.6.38/lib/kref.c:34
After debugging uss720 driver i discovered that the completion callback was called before
usb_submit_urb returns. The callback frees the request structure that is krefed on return by
usb_submit_urb.
Signed-off-by: Peter Holik <peter@holik.at>
Acked-by: Thomas Sailer <t.sailer@alumni.ethz.ch>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The common code has a "get" in the middle, but each implementation
does not have it.
Cc: stable@kernel.org
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: stable@kernel.org
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The modularization of the Blackfin driver set the name to "musb-blackfin"
in all the boards, but "musb-bfin" in the driver itself. Since the driver
file name uses "blackfin", change the driver to "musb-blackfin". This is
also easier as it's only one file to change.
Cc: stable@kernel.org
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There was conflict while merging 2 patches. Enabling vbus code
is wrongly moved to error check if loop.
This is a fix to resolve the merge issue.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1453) fixes a long-standing bug in the ehci-hcd driver.
There is no need to set the Halt bit in the overlay region for an
unlinked or blocked QH. Contrary to what the comment says, setting
the Halt bit does not cause the QH to be patched later; that decision
(made in qh_refresh()) depends only on whether the QH is currently
pointing to a valid qTD. Likewise, setting the Halt bit does not
prevent completions from activating the QH while it is "stopped"; they
are prevented by the fact that qh_completions() temporarily changes
qh->qh_state to QH_STATE_COMPLETING.
On the other hand, there are circumstances in which the QH will be
reactivated _without_ being patched; this happens after an URB beyond
the head of the queue is unlinked. Setting the Halt bit will then
cause the hardware to see the QH with both the Active and Halt bits
set, an invalid combination that will prevent the queue from
advancing and may even crash some controllers.
Apparently the only reason this hasn't been reported before is that
unlinking URBs from the middle of a running queue is quite uncommon.
However Test 17, recently added to the usbtest driver, does exactly
this, and it confirms the presence of the bug.
In short, there is no reason to set the Halt bit for an unlinked or
blocked QH, and there is a very good reason not to set it. Therefore
the code that sets it is removed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Andiry Xu <andiry.xu@amd.com>
CC: David Brownell <david-b@pacbell.net>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When `echo Y > /sys/module/usbcore/parameters/usbfs_snoop` and
usb_control_msg() returns error, a lot of kernel memory is dumped to dmesg
until unhandled kernel paging request occurs.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Under certain workloads a command may seem to get lost. IOW, the Smart Array
thinks all commands have been completed but we still have commands in our
completion queue. This may lead to system instability, filesystems going
read-only, or even panics depending on the affected filesystem. We add an
extra read to force the write to complete.
Testing shows this extra read avoids the problem.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This prevents possible race between bond_enslave and bond_handle_frame
as reported by Nicolas by moving rx_handler register/unregister.
slave->bond is added to hold pointer to master bonding sructure. That
way dev->master is no longer used in bond_handler_frame.
Also, this removes "BUG: scheduling while atomic" message
Reported-by: Nicolas de Pesloüan <nicolas.2p.debian@gmail.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Tested-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rmmod myri10ge crash at free_netdev() -> netif_napi_del(), because napi
structures are already deallocated. To fix call netif_napi_del() before
kfree() at myri10ge_free_slices().
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Doorbell is used according to usage of BlueFlame.
For Blue Flame to work in Ethernet mode QP number should have 0
at bits 6,7.
Allocating range of QPs accordingly.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not allow a kernel consumer to allocate a UAR to serve for blue flame if the
number of available UARs gets below MLX4_NUM_RESERVED_UARS (currently 8). This
will allow userspace apps to open a device file and run things like
ibv_devinfo.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mlx4_bitmap_avail() to give the number of available resources. We want to
use this as a hint to whether to allocate a resources or not. This patch is
introduced to be used with allocation blue flame registers.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using blue flame can improve latency by allowing the HW to more efficiently
access the WQE. This patch presents two functions that are used to allocate or
release HW resources for using blue flame; the caller need to supply a struct
mlx4_bf object when allocating resources. Consumers that make use of this API
should post doorbells to the UAR object pointed by the initialized struct
mlx4_bf;
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx4_en module now uses the new steering mechanism.
The RX packets are now steered through the MCG table instead
of Mac table for unicast, and default entry for multicast.
The feature is enabled through INIT_HCA
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Ethernet mode only,
When we want to register QP as promiscuous, it must be added to all the
existing steering entries and also to the default one.
The promiscuous QP might also be on of "real" QPs,
which means we need to monitor every entry to avoid duplicates and ensure
we close an entry when all it has is promiscuous QPs.
Same mechanism both for unicast and multicast.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same packet steering mechanism would be used both for IB and Ethernet,
Both multicasts and unicasts.
This commit prepares the general infrastructure for this.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW revision is derived from device ID and rev id.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver queries the FW for WOL support.
Ethtool get/set_wol is implemented accordingly.
Only magic packets are supported at the time.
Signed-off-by: Igor Yarovinsky <igory@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each RX ring will have its own interrupt vector, and TX rings will share one
(we mostly use polling for TX completions).
The vectors are assigned first time device is opened, and its name includes
the interface name and ring number.
Signed-off-by: Markuze Alex <markuze@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a pool of MSI-X vectors and EQs that can be used explicitly by mlx4_core
customers (mlx4_ib, mlx4_en). The consumers will assign their own names to the
interrupt vectors. Those vectors are not opened at mlx4 device initialization,
opened by demand.
Changed the max number of possible EQs according to the new scheme, no longer relies on
on number of cores.
The new functionality is exposed through mlx4_assign_eq() and mlx4_release_eq().
Customers that do not use the new API will get completion vectors as before.
Signed-off-by: Markuze Alex <markuze@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of reseting the module parameters each ifup or mtu change,
they are being set once at device initialization
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 86271e460a introduced a
regression that caused mac80211 queues in stopped state.
ath_drain_all_txq is called in driver flush which would reset
the stopped flag and the mac80211 queues were never started
after that. iperf traffic is completely stalled due to this issue.
Restart the mac80211 queues in driver flush only if the txqs were
drained.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the recent tx status optimization in mac80211, we bail out as
and and when invalid rate index is found. So the behavior of resetting
rate idx to -1 and count to 0 has changed for the rate indexes that
were not part of the driver's retry series.
This has resulted in ath9k using incorrect rate table index which
caused the system to panic. Ideally ath9k need to loop only for the
indexes that were part of the retry series and so simply use hw->max_rates
as the loop counter.
Pasted the stack trace of the panic issue for reference.
[ 754.093192] BUG: unable to handle kernel paging request at ffff88046a9025b0
[ 754.093256] IP: [<ffffffffa02eac49>] ath_tx_status+0x209/0x2f0 [ath9k]
[ 754.094888] Call Trace:
[ 754.094903] <IRQ>
[ 754.094928] [<ffffffffa051f883>] ieee80211_tx_status+0x203/0x9e0 [mac80211]
[ 754.094975] [<ffffffffa053e305>] ? __ieee80211_wake_queue+0x125/0x140 [mac80211]
[ 754.095017] [<ffffffffa02e66c9>] ath_tx_complete_buf+0x1b9/0x370 [ath9k]
[ 754.095054] [<ffffffffa02e6fcf>] ath_tx_complete_aggr+0x51f/0xb50 [ath9k]
[ 754.095098] [<ffffffffa05382a3>] ? ieee80211_prepare_and_rx_handle+0x173/0xab0 [mac80211]
[ 754.095148] [<ffffffff81350e62>] ? _raw_spin_unlock_irqrestore+0x32/0x40
[ 754.095186] [<ffffffffa02e9735>] ath_tx_tasklet+0x365/0x4b0 [ath9k]
[ 754.095224] [<ffffffff8107a2a2>] ? clockevents_program_event+0x62/0xa0
[ 754.095261] [<ffffffffa02e2628>] ath9k_tasklet+0x168/0x1c0 [ath9k]
[ 754.095298] [<ffffffff8105599b>] tasklet_action+0x6b/0xe0
[ 754.095331] [<ffffffff81056278>] __do_softirq+0x98/0x120
[ 754.095361] [<ffffffff8100cd5c>] call_softirq+0x1c/0x30
[ 754.095393] [<ffffffff8100efb5>] do_softirq+0x65/0xa0
[ 754.095423] [<ffffffff810563fd>] irq_exit+0x8d/0x90
[ 754.095453] [<ffffffff8100ebc1>] do_IRQ+0x61/0xe0
[ 754.095482] [<ffffffff81351413>] ret_from_intr+0x0/0x15
[ 754.095513] <EOI>
[ 754.095531] [<ffffffff81014375>] ? native_sched_clock+0x15/0x70
[ 754.096475] [<ffffffffa02bcfa6>] ? acpi_idle_enter_bm+0x24d/0x285 [processor]
[ 754.096475] [<ffffffffa02bcf9f>] ? acpi_idle_enter_bm+0x246/0x285 [processor]
[ 754.096475] [<ffffffff8127fab2>] cpuidle_idle_call+0x82/0x100
[ 754.096475] [<ffffffff8100a236>] cpu_idle+0xa6/0xf0
[ 754.096475] [<ffffffff81339bc1>] rest_init+0x91/0xa0
[ 754.096475] [<ffffffff814efccd>] start_kernel+0x3fd/0x408
[ 754.096475] [<ffffffff814ef347>] x86_64_start_reservations+0x132/0x136
[ 754.096475] [<ffffffff814ef451>] x86_64_start_kernel+0x106/0x115
[ 754.096475] RIP [<ffffffffa02eac49>] ath_tx_status+0x209/0x2f0 [ath9k]
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On hardware busy the scan request pointer should be cleared, as higher
levels will release. This avoids a crash when that pointer is
erroneously used later.
Signed-off-by: Joseph J. Gunn <armadefuego@yahoo.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clearly a mistake, since pointers won't suddenly
change their value...
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the TCM_Loop Linux/SCSI LLD fabric module for
accessing TCM device backstores as locally accessable SCSI LUNs in
virtual SAS, FC, and iSCSI Target ports using the generic fabric
TransportID and Target Port WWN naming handlers from TCM's
target_core_fabric_lib.c The TCM_Loop module uses the generic fabric
configfs infratructure provided by target_core_fabric_configfs.c and
adds a module dependent attribute for the creation/release of the
virtual I_T Nexus connected the TCM_Loop Target and Initiator Ports.
TCM_Loop can also be used with scsi-generic and BSG drivers so that
STGT userspace fabric modules, QEMU-KVM and other hypervisor SCSI
passthrough support can access TCM device backstore and control CDB
emulation.
For more information please see:
http://linux-iscsi.org/wiki/Tcm_loop
[jejb: fixed up checkpatch stuff]
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Disable Interrupt MBX completion will disable the interrupt on
successful completion. Fixed the bug where driver was waiting for
Interrupt to come in for its completion. Now driver will poll for
disable interrupt MBX completion.
Signed-off-by: Sarang Radke <sarang.radke@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This reverts commit 24d720b726.
Previously we thought there was little possibility that devices would
crash with this, but some have been found.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Driver does not detect a new CQE (completion queue entry) if a thread receives
the wakup when it is in TASK_RUNNING state. Fix is to set the state to
TASK_INTERRUPTIBLE while holding the fp_work_lock.
Also, Use __set_current_task() since it is now set inside a spinlock with
synchronization.
Two other related optimizations:
1. After we exit the while (!kthread_should_stop()) loop, use
__set_current_state() since synchronization is no longer needed.
2. Remove set_current_state(TASK_RUNNING) after schedule() since it
should always be TASK_RUNNING after schedule().
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Move relogin to all devices code from do_dpc to new
fuction qla4xxx_relogin_all_devices()
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jan Altenberg