There are two types of 160 MHz spectral scan support mentioned below
1. Fragmented approach
2. Single event approach
In this fragmented approach, single 160 MHz will be split as two
80 MHz buffer. First fft sample buffer will contain spectral scan
result of primary 80 MHz and the second fft sample buffer will contain
secondary 80 MHz and here cfreq1 and cfreq2 will be mentioned.
In case of 160 MHz on 36th channel will contain cfreq1 as 5210 and
cfreq2 as 5290. Chipsets which support this approach are IPQ8074/IPQ6018.
Replacing freq1 with freq2 in every secondary sepctral scan event to
distinguish between two different 80 MHz spectral event data.
In the 2nd approach each fft sample buffer will contain spectral scan
result for whole 160 MHz by mentioning cfreq1 as 5250 which is center
frequency of whole 160 MHz. Chipset which support this approach is QCN9074.
Host will receive spectral event from target for every 5 fft samples.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01120-QCAHKSWPL-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01120-QCAHKSWP
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220725055001.15194-1-quic_tamizhr@quicinc.com
Add support to get the following power save information through debugfs interface,
* Current ps state of the peer
* Time duration since the peer is in power save
* Total duration of the peer spent in power save
Above information is helpful in debugging the issues with power save clients.
This patch also add trace log support for PS timekeeper to track the PS state
change of the peers alongs with the peer MAC address and timestamp.
Use the below commands to get the above power save information,
To know the time_since_station_in_power_save:
cat /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/
XX:XX:XX:XX:XX:XX/current_ps_duration
To know power_save_duration:
cat /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/
XX:XX:XX:XX:XX:XX/total_ps_duration
To reset the power_save_duration of all stations connected to AP:
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath11k/reset_ps_duration
To enable/disable the ps_timekeeper:
echo Y > /sys/kernel/debug/ieee80211/phyX/ath11k/ps_timekeeper_enable
Y = 1 to enable and Y = 0 to disable.
To record PS timekeeer logs after enabling ps_timekeeper:
trace-cmd record -e ath11k_ps_timekeeper
Tested-on: Tested-on: IPQ8074 WLAN.HK.2.5.0.1-00991-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220725054601.14719-1-quic_tamizhr@quicinc.com
This patch try to fix the following error.
Wed Jun 1 22:19:30 2022 kern.warn kernel: [ 119.561227] ath11k c000000.wifi: peer already added vdev id 0 req, vdev id 1 present
Wed Jun 1 22:19:30 2022 kern.warn kernel: [ 119.561282] ath11k c000000.wifi: Failed to add peer: 28:c2:1f:xx:xx:xx for VDEV: 0
Wed Jun 1 22:19:30 2022 kern.warn kernel: [ 119.568053] ath11k c000000.wifi: Failed to add station: 28:c2:1f:xx:xx:xx for VDEV: 0
Wed Jun 1 22:19:31 2022 daemon.notice hostapd: wlan2: STA 28:c2:1f:xx:xx:xx IEEE 802.11: Could not add STA to kernel driver
Wed Jun 1 22:19:31 2022 daemon.notice hostapd: wlan2: STA 28:c2:1f:xx:xx:xx IEEE 802.11: did not acknowledge authentication response
Wed Jun 1 22:19:31 2022 daemon.notice hostapd: wlan1: AP-STA-DISCONNECTED 28:c2:1f:xx:xx:xx
Wed Jun 1 22:19:31 2022 daemon.info hostapd: wlan1: STA 28:c2:1f:xx:xx:xx IEEE 802.11: disassociated due to inactivity
Wed Jun 1 22:19:32 2022 daemon.info hostapd: wlan1: STA 28:c2:1f:xx:xx:xx IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE)
To repro this:
- Have 2 Wifi with the same bssid and pass on different band (2.4 and
5GHz)
- Enable 802.11r Fast Transaction with same mobility domain
- FT Protocol: FT over the Air
From a openwrt system issue the command (with the correct mac)
ubus call hostapd.wlan1 wnm_disassoc_imminent '{"addr":"28:C2:1F:xx:xx:xx"}'
Notice the log printing the errors.
The cause of this error has been investigated and we found that this is
related to the WiFi Fast Transaction feature. We observed that this is
triggered when the router tells the device to change band. In this case
the device first auth to the other band and then the disconnect path
from the prev band is triggered.
This is problematic with the current rhash implementation since the
addrs is used as key and the logic of "adding first, delete later"
conflicts with the rhash logic.
In fact peer addition will fail since the peer is already added and with
that fixed a peer deletion will cause unitended effect by removing the
peer just added.
Current solution to this is to add additional logic to the peer delete,
make sure we are deleting the correct peer taken from the rhash
table (and fallback to the peer list) and for the peer add logic delete
the peer entry for the rhash list before adding the new one (counting as
an error only when a peer with the same vlan_id is asked to be added).
With this change, a sta can correctly transition from 2.4GHz and 5GHZ
with no drop and no error are printed.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Fixes: 7b0c70d92a ("ath11k: Add peer rhash table support")
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220603164559.27769-1-ansuelsmth@gmail.com
The number of spatial streams used when acting as a beamformee in VHT
mode are reported by the firmware as 7 (8 sts - 1) both in IPQ6018 and
IPQ8074 which respectively have 2 and 4 sts each. So the firmware should
report 1 (2 - 1) and 3 (4 - 1).
Fix this by checking that the number of VHT beamformee sts reported by
the firmware is not greater than the number of receiving antennas - 1.
The fix is based on the same approach used in this same function for
sanitizing the number of sounding dimensions reported by the firmware.
Without this change, acting as a beamformee in VHT mode is not working
properly.
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Jesus Fernandez Manzano <jesus.manzano@galgus.net>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220616173947.21901-1-jesus.manzano@galgus.net
Devices may provide their own MAC address via system firmware (e.g.,
device tree), especially in the case where the device doesn't have a
useful EEPROM on which to store its MAC address (e.g., for integrated
ahb WCN6750).
Use the generic device helper to retrieve the MAC address, and (if
present) honor it above the MAC address advertised by the card.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Jun Yu <junyuu@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220920003117.841442-1-junyuu@chromium.org
Driver does not support get_txpower mac ops because of which
cfg80211 returns vif->bss_conf.txpower to user space. bss_conf.txpower
gets its value from ieee80211_channel->max_reg_power. However, the final
txpower is dependent on few other parameters apart from max regulatory
supported power. It is the firmware which knows about all these
parameters and considers the minimum for each packet transmission.
All ath11k firmware reports the final tx power in firmware pdev stats
which falls under fw_stats.
Add get_txpower mac ops to get the tx power from firmware leveraging
fw_stats and return it accordingly.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220603082814.31466-3-quic_adisi@quicinc.com
Currently, firmware stats, comprising pdev, vdev and beacon stats are
part of debugfs. In firmware pdev stats, firmware reports the final
Tx power used to transmit each packet. If driver wants to know the
final Tx power being used at firmware level, it can leverage from
firmware pdev stats.
Move firmware stats out of debugfs context in order to leverage
the final Tx power reported in it even when debugfs is disabled.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220603082814.31466-2-quic_adisi@quicinc.com
When running suspend test, kernel crash happened in ath10k, and it is
fixed by commit b72a4aff94 ("ath10k: skip ath10k_halt during suspend
for driver state RESTARTING").
Currently the crash is fixed, but as a common code style, it is better
to set the pointer to NULL after memory is free.
This is to address the code style and it will avoid potential bug of
use-after-free.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220505092248.787-1-quic_wgong@quicinc.com
It has a fail log which is ath11k_dbg in ath11k_dp_rx_process_mon_status(),
as below, it will not print when debug_mask is not set ATH11K_DBG_DATA.
ath11k_dbg(ab, ATH11K_DBG_DATA,
"failed to find the peer with peer_id %d\n",
ppdu_info.peer_id);
When run scan with station disconnected, the peer_id is 0 for case
HAL_RX_MPDU_START in ath11k_hal_rx_parse_mon_status_tlv() which called
from ath11k_dp_rx_process_mon_status(), and the peer_id of ppdu_info is
reset to 0 in the while loop, so it does not match condition of the
check "if (ppdu_info->peer_id == HAL_INVALID_PEERID" in the loop, and
then the log "failed to find the peer with peer_id 0" print after the
check in the loop, it is below call stack when debug_mask is set
ATH11K_DBG_DATA.
The reason is this commit 01d2f285e3 ("ath11k: decode HE status tlv")
add "memset(ppdu_info, 0, sizeof(struct hal_rx_mon_ppdu_info))" in
ath11k_dp_rx_process_mon_status(), but the commit does not initialize
the peer_id to HAL_INVALID_PEERID, then lead the check mis-match.
Callstack of the failed log:
[12335.689072] RIP: 0010:ath11k_dp_rx_process_mon_status+0x9ea/0x1020 [ath11k]
[12335.689157] Code: 89 ff e8 f9 10 00 00 be 01 00 00 00 4c 89 f7 e8 dc 4b 4e de 48 8b 85 38 ff ff ff c7 80 e4 07 00 00 01 00 00 00 e9 20 f8 ff ff <0f> 0b 41 0f b7 96 be 06 00 00 48 c7 c6 b8 50 44 c1 4c 89 ff e8 fd
[12335.689180] RSP: 0018:ffffb874001a4ca0 EFLAGS: 00010246
[12335.689210] RAX: 0000000000000000 RBX: ffff995642cbd100 RCX: 0000000000000000
[12335.689229] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff99564212cd18
[12335.689248] RBP: ffffb874001a4dc0 R08: 0000000000000001 R09: 0000000000000000
[12335.689268] R10: 0000000000000220 R11: ffffb874001a48e8 R12: ffff995642473d40
[12335.689286] R13: ffff99564212c5b8 R14: ffff9956424736a0 R15: ffff995642120000
[12335.689303] FS: 0000000000000000(0000) GS:ffff995739000000(0000) knlGS:0000000000000000
[12335.689323] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[12335.689341] CR2: 00007f43c5d5e039 CR3: 000000011c012005 CR4: 00000000000606e0
[12335.689360] Call Trace:
[12335.689377] <IRQ>
[12335.689418] ? rcu_read_lock_held_common+0x12/0x50
[12335.689447] ? rcu_read_lock_sched_held+0x25/0x80
[12335.689471] ? rcu_read_lock_held_common+0x12/0x50
[12335.689504] ath11k_dp_rx_process_mon_rings+0x8d/0x4f0 [ath11k]
[12335.689578] ? ath11k_dp_rx_process_mon_rings+0x8d/0x4f0 [ath11k]
[12335.689653] ? lock_acquire+0xef/0x360
[12335.689681] ? rcu_read_lock_sched_held+0x25/0x80
[12335.689713] ath11k_dp_service_mon_ring+0x38/0x60 [ath11k]
[12335.689784] ? ath11k_dp_rx_process_mon_rings+0x4f0/0x4f0 [ath11k]
[12335.689860] call_timer_fn+0xb2/0x2f0
[12335.689897] ? ath11k_dp_rx_process_mon_rings+0x4f0/0x4f0 [ath11k]
[12335.689970] run_timer_softirq+0x21f/0x540
[12335.689999] ? ktime_get+0xad/0x160
[12335.690025] ? lapic_next_deadline+0x2c/0x40
[12335.690053] ? clockevents_program_event+0x82/0x100
[12335.690093] __do_softirq+0x151/0x4a8
[12335.690135] irq_exit_rcu+0xc9/0x100
[12335.690165] sysvec_apic_timer_interrupt+0xa8/0xd0
[12335.690189] </IRQ>
[12335.690204] <TASK>
[12335.690225] asm_sysvec_apic_timer_interrupt+0x12/0x20
Reset the default value to HAL_INVALID_PEERID each time after memset
of ppdu_info as well as others memset which existed in function
ath11k_dp_rx_process_mon_status(), then the failed log disappeared.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: 01d2f285e3 ("ath11k: decode HE status tlv")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220518033556.31940-1-quic_wgong@quicinc.com
Currently commit 1f682dc9fb ("ath11k: reduce the wait time of 11d scan
and hw scan while add interface") introduced a wait_for_completion_timeout
operation for ar->scan.completed, another one is existed in ath11k_scan_stop(),
then ath11k has two places to wait for the ar->scan.completed and they
run in different thread, thus it is possible to happend that the two
thread both enter wait status. To handle this scenario, ath11k should
change the complete() to complete_all() for the ar->scan.completed. This
also work well when it is only one thread wait for ar->scan.completed.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220919024413.25083-1-quic_wgong@quicinc.com
Add support for WoW on WCN6750 chipset.
Unlike other chips where WoW exit happens after sending WoW wakeup
WMI command, exit from WoW suspend in the case of WCN6750 happens
upon sending a WoW exit SMP2P (Shared memory point to point) message
to the firmware.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220902112520.24804-3-quic_mpubbise@quicinc.com
Add required bindings to support WoW (Wake on Wireless) on
WCN6750 which is based on ath11k driver.
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220902112520.24804-2-quic_mpubbise@quicinc.com
In current code STA_KEEPALIVE_ARP_RESPONSE TLV header is included only
when ARP method is used, this causes firmware always to crash when wowlan
is enabled because firmware needs it to be present no matter ARP method
is used or not.
Fix this issue by including STA_KEEPALIVE_ARP_RESPONSE TLV header by
default.
Also fix below typo:
s/WMI_TAG_STA_KEEPALVE_ARP_RESPONSE/WMI_TAG_STA_KEEPALIVE_ARP_RESPONSE/
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: 0f84a156aa ("ath11k: Handle keepalive during WoWLAN suspend and resume")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220913044358.2037-1-quic_bqiang@quicinc.com
The signal-to-noise-ratio SNR is returned by the wcn36xx firmware for each
received frame. SNR represents all of the unwanted interference signal
after filtering out the fundamental frequency and harmonics of the
frequency.
Noise can come from various electromagnetic sources, from temperature
affecting the performance hardware components or quantization effects
converting from analog to digital domains.
The SNR value returned by the WiFi firmware then is a good source of
entropy.
Other WiFi drivers offer up the noise component of the FFT as an entropy
source for the random pool e.g.
commit 2aa56cca35 ("ath9k: Mix the received FFT bins to the random pool")
I attended Jason's talk on sources of randomness at Plumbers and it
occurred to me that SNR is a reasonable candidate to add.
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220915004117.1562703-2-bryan.odonoghue@linaro.org
Fix documentation issues reported by kernel-doc:
- Incorrect use of /** for non-kernel-doc comments
- Mismatch between documented and actual identifiers
- Incorrect identifier syntax
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220909151246.22961-1-quic_jjohnson@quicinc.com
Increase TCL data ring size to 2048 for WCN6750. This is
needed to meet 160 MHz TX throughput.
Add a new hw_param to indicate the TX ring size for
individual devices.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220905071805.31625-4-quic_mpubbise@quicinc.com
Currently in the case of WCN6750, only one TCL ring is used for TX,
this is limiting the TX throughput in 160 MHz case, enabling multiple
TCL rings on WCN6750 has shown an improvement of nearly 300 Mbps in
the case of TCP TX, therefore add the support of multi TX ring for
WCN6750.
Currently TCL ring is selected based on CPU ID, this logic cannot be
applied for WCN6750 as there is chance of out of order TX of packets
and to avoid this, choose TCL ring based on flow hash so that packets
of the same flow will end up on same TCL ring. For the same reason,
TCL ring retry logic is also not applicable for WCN6750.
Also the mapping of TCL, WBM & RBM IDs for WCN6750 is different from
existing devices. Create a new TCM/WBM/RBM mapping for WCN6750.
Change does not impact existing ath11k devices.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220905071805.31625-3-quic_mpubbise@quicinc.com
Enable threaded NAPI on all ath11k targets. Unlike traditional
NAPI poll which runs in softirq context and on the core which
scheduled the NAPI, threaded NAPI makes use of kernel threads
which are under direct control of the scheduler and helps in
balancing the NAPI processing load across multiple CPUs thereby
improving throughput.
In the case of WCN6750, enabling threaded NAPI has improved
160 MHz RX throughput by nearly 400 Mbps. Similar gains can
be expected on other ath11k devices as well.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220905071805.31625-2-quic_mpubbise@quicinc.com
mhi_alloc_controller() allocates a memory space for mhi_ctrl. When gets
some error, mhi_ctrl should be freed with mhi_free_controller(). But
when ath11k_mhi_read_addr_from_dt() fails, the function returns without
calling mhi_free_controller(), which will lead to a memory leak.
We can fix it by calling mhi_free_controller() when
ath11k_mhi_read_addr_from_dt() fails.
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220907073704.58806-1-niejianglei2021@163.com
On-board SRAM contains valuable information for firmware debugging so
add a new file named "sram" to debugfs with which we can dump SRAM
content using following the following:
cp /sys/kernel/debug/ath11k/wcn6855\ hw2.0/sram /tmp/sram
Currently this feature is enabled for QCA6390 and WCN6855.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220802075533.1744-3-quic_bqiang@quicinc.com
ath11k_pcic_write32/read32 tries to do wake up before doing actual
write/read work, which means each time a u32 is written/read, wake
up is performed. This is not necessary in case where we do a
large amount of write/read, because only one time of wake up is needed.
So split each one into two parts, the first part does wake up and
release, and the second one does actual write/read work.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220802075533.1744-2-quic_bqiang@quicinc.com
Enable remain on channel support on WCN6750 as it is needed for
GAS, Passpoint.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220901080656.3450-1-quic_mpubbise@quicinc.com
Add support to connect to a non-transmit MBSSID AP profile.
Non-transmit MBSSID profile parameters are passed to the firmware
via WMI VDEV UP command and this helps firmware to track MBSSID
profile within the multi-BSS beacon and report beacon loss if
any.
WCN6750, QCA6390 & WCN6855 firmwares have the support and hence
enable the support on these hardwares.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220901080616.29414-1-quic_mpubbise@quicinc.com
Currently, creation of debugfs entries for TWT is failing during
hardware restart because of the residual TWT files which were
created during add_interface(). Since, struct arvif{} is memset
to zero upon add_interface() invocation, when the hardware restart
is triggered, arvif is memset to 0 and TWT files are attempted to
create again which will fail because of the residual TWT files
already in place, this leads to hardware restart failure.
Also, it is not a good idea to return error from add_interface()
because of debugfs file creation failures. Moreover, debugfs
framework can very well handle the errors in it's create file &
remove file APIs and the errors returned by these APIs are not
checked in most usecases.
Fix the HW restart failure by ignoring the errors returned from
the debugfs APIs.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Fixes: fe98a6137d ("ath11k: add debugfs for TWT debug calls")
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220720135150.22193-3-quic_mpubbise@quicinc.com
Currently TWT debugfs files required for manually testing the
TWT feature are created only for the AP interfaces; these debugfs
hooks are also required for the station interfaces in order to
test the TWT feature manually, therefore create these debugfs
hooks for station iftype as well.
In the case of station interfaces, TWT is entirely handled in the
firmware based on input parameters passed to it during association
via TWT enable WMI command. In order to manually test this feature,
firmware expects to first disable the TWT feature and then send the
enable command with sta_cong_timer_ms parameter set to 0.
This is true for WCN6750, QCA6390 & WCN6855 hardwares.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220720135150.22193-2-quic_mpubbise@quicinc.com
Add cold boot calibration support on WCN6750. Unlike other
chipsets where firmware(FW) is restarted after cold boot
calibration is completed, it is recommended not to restart
the firmware for WCN6750.
For WCN6750, FW sends both CAL_DONE & FW_READY QMI indication
to the driver after cold boot calibration is completed.
QMI message flow for WCN6750 with cold boot support:
FW_INIT_DONE to HOST -> CALIBRATION Mode to FW -> CAL_DONE to Host ->
FW_READY to Host -> MODE_ON to FW
QMI message flow for other chipsets with cold boot support:
FW_INIT_DONE to Host -> CALIBRATION Mode to FW -> FW_READY to Host ->
Trigger FW restart -> FW_INIT_DONE to HOST -> MODE_ON to FW
QMI message flow for chipsets without cold boot support:
FW_INIT_DONE to Host -> MODE_ON to FW
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220720134909.15626-3-quic_mpubbise@quicinc.com
QMI message IDs for some of the QMI messages were incorrectly
defined in the original implementation. These have to be corrected
to enable cold boot support on WCN6750. These corrections are
applicable for all chipsets and will not impact them. Refactor the
code accordingly.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220720134909.15626-2-quic_mpubbise@quicinc.com
When the system shuts down, SMMU driver will be stopped and
will not assist in IOVA translations. SMMU driver expects all
of its consumers to shutdown before shutting down itself.
WCN6750 being one of the consumer device should not perform any
DMA operations after the SMMU has shutdown which will otherwise
result in SMMU faults.
SMMU driver will call the shutdown() callback of all its
consumer devices and the consumers shall stop further DMA
activity after the invocation of their respective shutdown()
callbacks.
Register the shutdown() callback to the platform core for WCN6750.
Change will not impact other AHB ath11k devices.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220720134710.15523-1-quic_mpubbise@quicinc.com
syzbot is reporting uninit value at ath9k_htc_rx_msg() [1], for
ioctl(USB_RAW_IOCTL_EP_WRITE) can call ath9k_hif_usb_rx_stream() with
pkt_len = 0 but ath9k_hif_usb_rx_stream() uses
__dev_alloc_skb(pkt_len + 32, GFP_ATOMIC) based on an assumption that
pkt_len is valid. As a result, ath9k_hif_usb_rx_stream() allocates skb
with uninitialized memory and ath9k_htc_rx_msg() is reading from
uninitialized memory.
Since bytes accessed by ath9k_htc_rx_msg() is not known until
ath9k_htc_rx_msg() is called, it would be difficult to check minimal valid
pkt_len at "if (pkt_len > 2 * MAX_RX_BUF_SIZE) {" line in
ath9k_hif_usb_rx_stream().
We have two choices. One is to workaround by adding __GFP_ZERO so that
ath9k_htc_rx_msg() sees 0 if pkt_len is invalid. The other is to let
ath9k_htc_rx_msg() validate pkt_len before accessing. This patch chose
the latter.
Note that I'm not sure threshold condition is correct, for I can't find
details on possible packet length used by this protocol.
Link: https://syzkaller.appspot.com/bug?extid=2ca247c2d60c7023de7f [1]
Reported-by: syzbot <syzbot+2ca247c2d60c7023de7f@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/7acfa1be-4b5c-b2ce-de43-95b0593fb3e5@I-love.SAKURA.ne.jp
* rtw88: operation, locking, warning, and code style fixes
* rtw89: small updates
* cfg80211/mac80211: more EHT/MLO (802.11be, WiFi 7) work
* brcmfmac: a couple of fixes
* misc cleanups etc.
-----BEGIN PGP SIGNATURE-----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=J5Fc
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2022-08-26-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes berg says:
====================
Various updates:
* rtw88: operation, locking, warning, and code style fixes
* rtw89: small updates
* cfg80211/mac80211: more EHT/MLO (802.11be, WiFi 7) work
* brcmfmac: a couple of fixes
* misc cleanups etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The Lenovo OneLink+ Dock contains an RTL8153 controller that behaves as
a broken CDC device by default. Add the custom Lenovo PID to the r8152
driver to support it properly.
Also, systems compatible with this dock provide a BIOS option to enable
MAC address passthrough (as per Lenovo document "ThinkPad Docking
Solutions 2017"). Add the custom PID to the MAC passthrough list too.
Tested on a ThinkPad 13 1st gen with the expected results:
passthrough disabled: Invalid header when reading pass-thru MAC addr
passthrough enabled: Using pass-thru MAC addr XX:XX:XX:XX:XX:XX
Signed-off-by: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-08-24 (ice)
This series contains updates to ice driver only.
Marcin adds support for TC parsing on TTL and ToS fields.
Anatolli adds support for devlink port split command to allow
configuration of various port configurations.
Jake allows for passing and writing an additional NVM write activate
field by expanding current cmd_flag.
Ani makes PHY debug output more readable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
clang reports uninitialized use:
>> drivers/net/wireless/realtek/rtw88/main.c:731:2: warning: variable
'primary_channel_idx' is used uninitialized whenever switch default is
taken [-Wsometimes-uninitialized]
default:
^~~~~~~
drivers/net/wireless/realtek/rtw88/main.c:754:39: note: uninitialized
use occurs here
hal->current_primary_channel_index = primary_channel_idx;
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/realtek/rtw88/main.c:687:24: note: initialize the
variable 'primary_channel_idx' to silence this warning
u8 primary_channel_idx;
^
= '\0'
This situation could not happen, because possible channel bandwidth
20/40/80MHz are enumerated.
Fixes: 341dd1f7de ("wifi: rtw88: add the update channel flow to support setting by parameters")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20220815062004.22920-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As per RGMII specification v2.0, section 3.4.1, RGMII/RTBI has an
optional in-band status feature where the PHY's link status, speed and
duplex mode can be passed to the MAC.
Allow RGMII/RTBI to use in-band status.
Signed-off-by: Qingfang DENG <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maksym Glubokiy says:
====================
net: prestera: matchall features
This patch series extracts matchall rules management out of SPAN API
implementation and adds 2 features on top of that:
- support for egress traffic (mirred egress action)
- proper rule priorities management between matchall and flower
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
matchall rules can be added only to chain 0 and their priorities have
limitations:
- new matchall ingress rule's priority must be higher (lower value)
than any existing flower rule;
- new matchall egress rule's priority must be lower (higher value)
than any existing flower rule.
The opposite works for flower rule adding:
- new flower ingress rule's priority must be lower (higher value)
than any existing matchall rule;
- new flower egress rule's priority must be higher (lower value)
than any existing matchall rule.
This is a hardware limitation and thus must be properly handled in
driver by reporting errors to the user when newly added rule has such a
priority that cannot be installed into the hardware.
To achieve this, the driver must maintain both min/max matchall
priorities for every flower block when user adds/deletes a matchall
rule, as well as both min/max flower priorities for chain 0 for every
adding/deletion of flower rules for chain 0.
Cc: Serhiy Boiko <serhiy.boiko@plvision.eu>
Signed-off-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds more clarity to handling of TC_CLSMATCHALL_REPLACE and
TC_CLSMATCHALL_DESTROY events by calling newly added *_mall_*() handlers
instead of directly calling SPAN API.
This also extracts matchall rules management out of SPAN API since SPAN
is a hardware module which is used to implement 'matchall egress mirred'
action only.
Signed-off-by: Taras Chornyi <tchornyi@marvell.com>
Signed-off-by: Serhiy Boiko <serhiy.boiko@plvision.eu>
Signed-off-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add phylink based ethtool pause configuration
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some exotic ax88772 based devices which may require
functionality provide by the phylink framework. For example:
- US100A20SFP, USB 2.0 auf LWL Converter with SFP Cage
- AX88772B USB to 100Base-TX Ethernet (with RMII) demo board, where it
is possible to switch between internal PHY and external RMII based
connection.
So, convert this driver to phylink as soon as possible.
Tested with:
- AX88772A + internal PHY
- AX88772B + external DP83TD510E T1L PHY
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.
Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tamizh Chelvam Raja