Enable the I2C bus mode if I2C_FUNC_I2C is set. Based on da6093 commit:
"586478bfc9f7 mfd: da9063: Support SMBus and I2C mode"
Signed-off-by: Andrej Picej <andrej.picej@norik.com>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211124065119.2514872-1-andrej.picej@norik.com
Use of_device_get_match_data() to make the code slightly smaller.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/da9062-core.c:614:34: warning: ‘da9062_dt_ids’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify a number of static struct resource. The only usage of the
structs are to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The da9062 interrupt handler cannot necessarily be low active.
Add a function to configure the interrupt type based on what is defined in the device tree.
The allowable interrupt type is either low or high level trigger.
Signed-off-by: Shreyas Joshi <shreyas.joshi@biamp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The watchdog driver compatible is "dlg,da9062-watchdog" and not
"dlg,da9062-wdt". Therefore the mfd-core can't populate the of_node and
fwnode. As result the watchdog driver can't parse the devicetree.
Fixes: 9b40b030c4 ("mfd: da9062: Supply core driver")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently the da9062 GPIO's aren't available. The patch adds the support
to make these available by adding a gpio device with the corresponding
irq resources. Furthermore the patch fixes a minor style issue for the
onkey device.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace multi-line entries in the regmap_range arrays with single
line macros: regmap_reg_range(). This will leave the static structure
array entries for regmap_range unaltered. It will significantly reduce
the line count in the DA9062/61 core file.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch was applied to the MFD twice, causing unwanted behavour.
This reverts commit b77eb79acc.
Fixes: b77eb79acc ("mfd: da9061: Fix to remove BBAT_CONT register from chip model")
Reported-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the register DA9062AA_BBAT_CONT (0x0C5) from the DA9061 chip model
regmap access ranges. This applies to both da9061_aa_readable_ranges[]
and da9061_aa_writeable_ranges[].
This change is to correct the DA9061 chip model and align it with the
latest DA9061 Datasheet.
This register previously appeared in the DA9061 Datasheet, Revision 3.2,
01-Mar-2016 and has been removed from later DA9061 datasheet from Dialog,
Revision 3.3, 04-Apr-2017.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the register DA9062AA_BBAT_CONT (0x0C5) from the DA9061 chip model
regmap access ranges. This applies to both da9061_aa_readable_ranges[]
and da9061_aa_writeable_ranges[].
This change is to correct the DA9061 chip model and align it with the
latest DA9061 Datasheet.
This register previously appeared in the DA9061 Datasheet, Revision 3.2,
01-Mar-2016 and has been removed from later DA9061 datasheet from Dialog,
Revision 3.3, 04-Apr-2017.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
MFD support for DA9061 is provided as part of the DA9062 device driver.
The registers header file adds two new chip variant IDs defined in DA9061
and DA9062 hardware. The core header file adds new software enumerations
for listing the valid DA9061 IRQs and a da9062_compatible_types enumeration
for distinguishing between DA9061/62 devices in software.
The core source code adds a new .compatible of_device_id entry. This is
extended from DA9062 to support both "dlg,da9061" and "dlg,da9062". The
.data entry now holds a reference to the enumerated device type.
A new regmap_irq_chip model is added for DA9061 and this supports the new
list of regmap_irq entries. A new mfd_cell da9061_devs[] array lists the
new sub system components for DA9061. Support is added for a new DA9061
regmap_config which lists the correct readable, writable and volatile
ranges for this chip.
The probe function uses the device tree compatible string to switch on the
da9062_compatible_types and configure the correct mfd cells, irq chip and
regmap config.
Kconfig is updated to reflect support for DA9061 and DA9062 PMICs.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add an updated set of registers listed in the core regmap_range volatile
ranges defined for the DA9062.
These new registers contain bits that cannot be considered under the full
control of software. Under various conditions the hardware will set and/or
automatically clear bit(s) contained in these registers.
When using a cached version of regmap, the volatility of these registers must
be identified otherwise the regmap operations may not ensure the registers
are explicitly altered.
As well as updating the list of volatile registers, this change will fix a
corner case discovered in the DA9063 ONKEY which is used by the DA9062 core.
In the ONKEY case, the CONTROL_B register is now listed as volatile in the
regmap_range because it contains the bit field NONKEY_LOCK. This bit can be
altered by hardware, in which case regmap must be notified of its ability
to be manpiulated outside of software control.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Rename get_device_type() to da9062_get_device_type().
This function is only used in this file so make it static.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add MFD core driver support for a OnKey component
- MFD core adds the resource da9062_onkey_resources[] for the OnKey
- An appropriate value has been added into mfd_cell da9062_devs[] to
support component .name = "da9062-onkey" and
.of_compatible = "dlg,da9062-onkey"
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add MFD core driver support for a RTC component
- MFD core adds the RTC resources da9062_rtc_resources[] for the RTC
alarm and tick timer IRQ
- An appropriate mfd_cell has been added into da9062_devs[] to support
a component .name = "da9062-rtc" and .of_compatible = "dlg,da9062-rtc"
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Andrej Picej