Our spinlocks are only 32-bit (2x16-bit tickets) and, on processors
with 64-bit atomic instructions, cmpxchg64 makes use of the double-word
exclusive accessors.
This patch wires up the cmpxchg-based lockless lockref implementation
for ARM.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch introduces cmpxchg64_relaxed for arm, which performs a 64-bit
cmpxchg operation without barrier semantics. cmpxchg64_local is updated
to use the new operation.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Our cmpxchg64 macros are wrappers around atomic64_cmpxchg. Whilst this is
great for code re-use, there is a case for barrier-less cmpxchg where it
is known to be safe (for example cmpxchg64_local and cmpxchg-based
lockrefs).
This patch introduces a 64-bit cmpxchg implementation specifically
for the cmpxchg64_* macros, so that it can be later used by the lockref
code.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This implements output of debug messages on efm32 SoCs.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
With LPAE enabled, physical address space is larger than 4GB. Allow mapping any
part of it via /dev/mem by using PHYS_MASK to determine valid range.
PHYS_MASK covers 40 bits with LPAE enabled and 32 bits otherwise.
Reported-by: Vassili Karpov <av1474@comtv.ru>
Signed-off-by: Sergey Dyasly <dserrg@gmail.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CS2 region contains the Assabet board configuration and status
registers, which are 32-bit. Unfortunately, some boot loaders do not
configure this region correctly, leaving it setup as a 16-bit region.
Fix this.
Cc: <stable@vger.kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This updates the h3600 defconfig against the latest kernel with
some small options coming and going due to Kconfig structure,
then modernize it to:
- Configure for low latency preemptive kernel
- Configure for tickless idle
- Enable HRtimers
Tested on the iPAQ h3630.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SA1100 was implementing its own variants of gpio_get_value()
and gpio_set_value() and only selectively falling back to
gpiolib for extended (EGPIO) handling. However the driver in
gpio/gpio-sa1100.c already handles the same functionality for
these lines, yet remain unused.
The only upside would be things like a timing-critical hotpath
on bit-banged GPIO, but that kind of things does not seem to
happen on these GPIOs, so it is not worth having the extra
complexity.
Tested with some buttons on the Compaq iPAQ H3630.
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When removing the complex GPIO interface from the SA1100 machines,
we also removed the implicit #includes for a few header files
that was included by <linux/gpio.h> thru <mach/gpio.h>, causing
a compile warning on the simpad boardfile, as <asm/irq.h> was no
longer #included, as follows:
./../arch/arm/include/asm/irq.h:9:0: warning: "NR_IRQS" redefined
[enabled by default]
#define NR_IRQS NR_IRQS_LEGACY
^
In file included from ../../arch/arm/mach-sa1100/simpad.c:29:0:
../../arch/arm/mach-sa1100/include/mach/irqs.h:87:0: note: this is the
location of the previous definition
#define NR_IRQS (IRQ_BOARD_START + NR_IRQS_LOCOMO)
This resolves the problem by explicitly including <asm/irq.h>
into the simpad boardfile.
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Cc: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 'f52bb722547f43caeaecbcc62db9f3c3b80ead9b'
Author: Sricharan R <r.sricharan@ti.com>
ARM: mm: Correct virt_to_phys patching for 64 bit physical addresses
introduced a __ARMEB__ macro usage in a new place, but missed the second
underscore. So correcting it here.
Also a explicit .align keyword is needed for the label with .long
data-type to be aligned on the 4 byte boundary. Otherwise this can
cause problem for thumb2 build. So adding it here.
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Two of the versatile irq definitions are incorrect, mostly because two
devices have connections to more than one interrupt controller. Fix them
by using the new interrupts-extended property to fan out without using
an awful interrupt-map nexus node.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The standard interrupts property in device tree can only handle
interrupts coming from a single interrupt parent. If a device is wired
to multiple interrupt controllers, then it needs to be attached to a
node with an interrupt-map property to demux the interrupt specifiers
which is confusing. It would be a lot easier if there was a form of the
interrupts property that allows for a separate interrupt phandle for
each interrupt specifier.
This patch does exactly that by creating a new interrupts-extended
property which reuses the phandle+arguments pattern used by GPIOs and
other core bindings.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
[grant.likely: removed versatile platform hunks into separate patch]
Cc: Rob Herring <rob.herring@calxeda.com>
This converts the gemini machine to use generic clockevents
by rewriting the timer driver.
Cc: arm@kernel.org
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add a lot of N900 nodes
Add OPP table to OMAP5/DRA7
Add support for Newflow NanoBone board
Add i2c aliases
Add McASP and audio support
Add reset/idle on init bindings for OMAP
Add more nodes for AM4272
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=8KX8
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Some more dts changes from Benoit Cousson <bcousson@baylibre.com> via
Tony Lindgren:
- Add a lot of N900 nodes
- Add OPP table to OMAP5/DRA7
- Add support for Newflow NanoBone board
- Add i2c aliases
- Add McASP and audio support
- Add reset/idle on init bindings for OMAP
- Add more nodes for AM4272
* tag 'omap-for-v3.13/dt-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (42 commits)
ARM: dts: omap5-uevm: Remove pinmux for dmic pins
ARM: dts: omap5-uevm: Correct twl6040 reset GPIO pinmux
ARM: dts: TWL4030: Add power button support
ARM: dts: omap3-n900: Add LP5523 support
ARM: dts: omap3-n900: Add TLV320AIC3X support
ARM: dts: omap3-n900:: Mux RX51_LCD_RESET_GPIO in DTS
ARM: dts: omap3-n900: Add NAND support
ARM: dts: omap3-n900: Specify regulator info
ARM: dts: TWL4030: Add missing regulators
ARM: dts: omap3-n900: Add LP5523 support
ARM: dts: omap3-n900: Add vibrator device
ARM: dts: omap3-n900: GPIO key definitions
ARM: dts: omap3-n900: Add support for SD cards
ARM: dts: omap3-n900: Add UART support
ARM: dts: omap3-n900: Fix i2c bus speed
ARM: dts: omap3-n900: Add pinctrl for i2c devices
ARM: dts: DRA7: Add CPU OPP table
ARM: dts: OMAP5: Add CPU OPP table
ARM: dts: dra7-evm: add smps123 supply for CPU
ARM: dts: omap5-uevm: add smps123 supply for CPU
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Note that this branch has a dependency to the patches merged
with omap-for-v3.13/board-removal-signed-take2.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=E/nA
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/cpufreq-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
Few patches to make cpufreq work for omap3 with device tree.
Note that this branch has a dependency to the patches merged
with omap-for-v3.13/board-removal-signed-take2.
* tag 'omap-for-v3.13/cpufreq-late' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3+: use cpu0-cpufreq driver in device tree supported boot
ARM: OMAP2+: add missing lateinit hook for calling pm late init
ARM: OMAP3+: do not register non-dt OPP tables for device tree boot
Signed-off-by: Olof Johansson <olof@lixom.net>
Move some of the OMAP2+ CM and System Control Module direct
register accesses into CM- and System Control
Module-specific "drivers" underneath arch/arm/mach-omap2/. This
is a prerequisite for moving this code out of arch/arm/mach-omap2/ into
drivers/.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/cm_scm_cleanup_a_v3.13/20131019101809/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=L37r
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/cm-scm-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Paul Walmsley <paul@pwsan.com> via Tony Lindgren:
Move some of the OMAP2+ CM and System Control Module direct
register accesses into CM- and System Control
Module-specific "drivers" underneath arch/arm/mach-omap2/. This
is a prerequisite for moving this code out of arch/arm/mach-omap2/ into
drivers/.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/cm_scm_cleanup_a_v3.13/20131019101809/
* tag 'omap-for-v3.13/cm-scm-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: control: add API for setting IVA bootmode
ARM: OMAP3: CM/control: move CM scratchpad save to CM driver
ARM: OMAP3: McBSP: do not access CM register directly
ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock
ARM: OMAP2: CM/PM: remove direct register accesses outside CM code
+ Linux 3.12-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
wait for the merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=WhmE
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/fixes-not-urgent-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes-non-critical
From Tony Lindgren:
Few more omap fixes that are not regressions or oopses and can
wait for the merge window.
* tag 'omap-for-v3.13/fixes-not-urgent-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: irq, AM33XX add missing register check
ARM: OMAP2+: wakeupgen: AM43x adaptation
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch enables all drivers and alike to make defconfig-ed
kernels use Versatile Express specific features, like power
management services (PSCI, MCPM with drivers for DCCSB on
Fast Models and SPC on TC2), CMA for frame buffer allocation,
all virtio device drivers (for QEMU, KVM tools and Fast Models),
MTD physmap drivers with squashfs and UBIFS for flash,
I2C master, regulator and hwmon drivers and LEDs support with
most useful triggers. The maximum amount of CPUs has been
increased to 8 to facilitate big.Little systems.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch updates the Versatile Express defconfig to a level
which makes it possible to run a defconfig-ed kernel work
on the board and in QEMU with modern userspace. It does:
- update cmdline to contain "console=ttyAMA0" only
- enable devtmpfs filesystem
- enable voltage regulator support
- enable ext4 filesystem
- disable low level debug and early printk
Signed-off-by: Fathi Boudra <fathi.boudra@linaro.org>
[PM: removed DEBUG_LL - it doesn't work on qemu]
[PM: reworded the commit message]
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* Use macros for mxs pinctrl settings
* New board support: VF610 Cosmic/Cosmic+, imx6q-udoo, MSR M28CU3
* Support DSPI device for vf610
* Add PCIe device for imx6qdl
* Add UHS pinctrl states for imx6sl and imx6qdl
* Display support for APF and imx51-babbage boards
* Enable SPI NOR and USB for imx6sl-evk board
* Enable LVDS for imx6q-sabrelite and SPDIF for imx6qdl-wandboard
* Misc updates on boards: TX28, imx6qdl-wandboard, imx53-qsb etc.
* Some random updates on imx51 device tree
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSZJgGAAoJEFBXWFqHsHzOskMIALiVd2Cs/Kl4LBufL5JM7JIz
Kh8mW24QmuwoMV0KHGEbzVlZbrIXyQj/8P89AnxaWTBhx9BKTBI1hWPrhCoXEGVQ
mxwpPce9WGiabwR0za9BEYnMOWo4E3s3XAb8rVm5I8d95oe42kCK+yJrhnG+2oQE
Z6+HRfmVTFcXtETcMwggOjgYdV+CRtXiMgoDFiQ10WSrv/9FI9bbS7fEirqEDzaR
4ZkAKNIjbeMYPi0VBbM7bjXezuPUswENyJQQurbCi/h51vpL/oPxEIJKJI3g8Kpi
KLcQu4VAWdzSrrKMdQpVqIcofJLLG5+LJGd7ay8zBGoGgyTtyrAEtwYIjzj/LGE=
=Ya6+
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-3.13' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
From Shawn Guo:
The imx/mxs device tree changes for 3.13:
- Use macros for mxs pinctrl settings
- New board support: VF610 Cosmic/Cosmic+, imx6q-udoo, MSR M28CU3
- Support DSPI device for vf610
- Add PCIe device for imx6qdl
- Add UHS pinctrl states for imx6sl and imx6qdl
- Display support for APF and imx51-babbage boards
- Enable SPI NOR and USB for imx6sl-evk board
- Enable LVDS for imx6q-sabrelite and SPDIF for imx6qdl-wandboard
- Misc updates on boards: TX28, imx6qdl-wandboard, imx53-qsb etc.
- Some random updates on imx51 device tree
* tag 'imx-dt-3.13' of git://git.linaro.org/people/shawnguo/linux-2.6: (44 commits)
ARM: imx: imx6sl iomuxc syscon is compatible to imx6q
ARM: dts: imx6sl-evk: enable the SPI NOR
ARM: dts: imx6sl: add a pinctrl for ECSPI1
ARM: imx27: add missing #pwm-cells property
ARM: dts: imx6sl: add pinctrl uhs states for usdhc
ARM: dts: imx6qdl-sabresd: Add backlight support for lvds
ARM: dts: imx51-babbage: Make DVI and WVGA panel functional
ARM: imx27-apf27dev: Add framebuffer support
ARM: imx51-apf51dev: Add parallel display support
ARM: dts: imx53-qsb: Do not use GPIO1_8 as wakeup source
ARM: dts: imx53-qsb: SDHC1 does not have cd-gpios
ARM: dts: imx53-qsb: SDHC3 is connected in 8-bit mode
ARM: dts: mxs: Add MSR M28CU3 board
ARM: dts: imx6qdl-wandboard: Provide phy-reset-gpios
ARM: dts: imx6qdl-sabresd: Provide phy-reset-gpios
ARM: dts: imx6q-sabrelite: Add ethernet phy reset pin into hog
ARM: dts: imx6qdl: add pcie device node
ARM: dts: imx6q-udoo: Add initial board support
ARM: dts: mxs: Add muxing options for the SSP2 MMC
ARM: dts: add initial VF610 Cosmic/Cosmic+ board support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
* Low-level debug support for Vybrid
* Support soc bus/device for imx6
* Suspend support for imx6dl and imx6sl
* The imx6q clock updates for PCIe and audio PLL support
* IOMUXC GPR update for fec support
* Some random cleanup
* A few defconfig updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSZI9RAAoJEFBXWFqHsHzOhgkH/RpZ6cvXFFaRdTWQu/SZCXTN
m3Ul0VpuaUp9gsbDNbu//OmqCAsayXaKI7PuJhs885zDKw6R3yMH7hbwXY7z0Qrq
jl9hP1Wzj7oU4CHTQbSDdcO3glUk+jl58a2MrsMsUaXPJTF8iMb8RkatwnReYhiZ
uCBXPwaet7SJTuVQOL1uJmq35LmiROwyAkGsDKnDmphg3ZDUiI9mhqlyOyrS522w
TjmCXrzZQiHkTp12Xo42fIEvE6BF5wCLDlJbq9HRDAlT82CnV62uQC/9os45Hott
H1pJbwdbcdv3+6gUdnWbraukrbhCxT8Yk0As4ljP6YBCxC7Sau+oMh3ii4pvuI0=
=VUrE
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-3.13' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
From Shawn Guo:
The imx/mxs soc changes for 3.13:
* Low-level debug support for Vybrid
* Support soc bus/device for imx6
* Suspend support for imx6dl and imx6sl
* The imx6q clock updates for PCIe and audio PLL support
* IOMUXC GPR update for fec support
* Some random cleanup
* A few defconfig updates
* tag 'imx-soc-3.13' of git://git.linaro.org/people/shawnguo/linux-2.6: (31 commits)
ARM: imx: enable suspend for imx6sl
ARM: imx: ensure dsm_request signal is not asserted when setting LPM
ARM: imx6q: call WB and RBC configuration from imx6q_pm_enter()
ARM: imx6q: move low-power code out of clock driver
ARM: imx: drop extern with function prototypes in common.h
ARM: imx: reset core along with enable/disable operation
ARM: imx: do not return from imx_cpu_die() call
ARM: imx_v6_v7_defconfig: Select CONFIG_PROVE_LOCKING
ARM: imx_v6_v7_defconfig: Enable LEDS_GPIO related options
ARM: mxs_defconfig: Turn off CONFIG_DEBUG_GPIO
ARM: imx: replace imx6q_restart() with mxc_restart()
ARM: mach-imx: mm-imx5: Retrieve iomuxc base address from dt
ARM: mach-imx: mm-imx5: Retrieve tzic base address from dt
ARM: mach-imx: clk-imx51-imx53: Retrieve base address and irq from dt
ARM: mxs_defconfig: Add CHIPIDEA_UDC support
ARM: imx: Include linux/err.h
ARM: imx_v6_v7_defconfig: Add CHIPIDEA_UDC support
ARM: imx_v6_v7_defconfig: Add SPDIF support
ARM: imx6q: clock and Kconfig update for PCIe support
ARM: imx: Add LVDS general-purpose clocks to i.MX6Q
...
Signed-off-by: Olof Johansson <olof@lixom.net>
From Maxime Ripard:
Allwinner sunXi defconfig changes for 3.13
This pull request only see the introduction of a sunxi_defconfig.
* tag 'sunxi-defconfig-for-3.13' of https://github.com/mripard/linux:
ARM: sunxi: Add a defconfig for the Allwinner SoCs
Signed-off-by: Olof Johansson <olof@lixom.net>
The machine entries were split up, but the cleanup to remove .init_time
removed the function that the new/split entries refer to. Remove them
since they are no longer needed.
Cc: Maxime Ripard <mripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Nothing outstanding here, mostly some documentation cleanup, and the split of
the previous generic machine declaration into three different machines to
handle the sun4i/sun5i, sun6i and sun7i separately.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=2aio
-----END PGP SIGNATURE-----
Merge tag 'sunxi-core-for-3.13' of https://github.com/mripard/linux into next/soc
From Maxime Ripard:
Allwinner sunXi SoCs machine additions for 3.13
Nothing outstanding here, mostly some documentation cleanup, and the split of
the previous generic machine declaration into three different machines to
handle the sun4i/sun5i, sun6i and sun7i separately.
* tag 'sunxi-core-for-3.13' of https://github.com/mripard/linux:
Documentation: dt: Remove clock gates IDs list for Allwinner SoCs
Documentation: dt: Remove interrupt sources list for Allwinner SoCs
Documentation: sunxi: Update Allwinner SoC documentation
Documentation: sunxi: Update A13 user manual dead link
ARM: sunxi: Order Kconfig options alphabetically
ARM: sunxi: Simplify restart setup code
ARM: sunxi: Split out the DT machines for sun6i and sun7i
Signed-off-by: Olof Johansson <olof@lixom.net>
Merging in dt clock cleanup as a pre-req with some of the later SoC branches.
There are a handful of conflicts here -- some of the already merged SoC
branches should have been based on the cleanup but weren't.
In particular, a remove/add of include on highbank and two remove/remove
conflicts on kirkwood were fixed up.
* cleanup/dt-clock: (28 commits)
ARM: vt8500: remove custom .init_time hook
ARM: vexpress: remove custom .init_time hook
ARM: tegra: remove custom .init_time hook
ARM: sunxi: remove custom .init_time hook
ARM: sti: remove custom .init_time hook
ARM: socfpga: remove custom .init_time hook
ARM: rockchip: remove custom .init_time hook
ARM: prima2: remove custom .init_time hook
ARM: nspire: remove custom .init_time hook
ARM: nomadik: remove custom .init_time hook
ARM: mxs: remove custom .init_time hook
ARM: kirkwood: remove custom .init_time hook
ARM: imx: remove custom .init_time hook
ARM: highbank: remove custom .init_time hook
ARM: exynos: remove custom .init_time hook
ARM: dove: remove custom .init_time hook
ARM: bcm2835: remove custom .init_time hook
ARM: bcm: provide common arch init for DT clocks
ARM: call of_clk_init from default time_init handler
ARM: vt8500: prepare for arch-wide .init_time callback
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Transparent Huge Pages and hugetlbfs support for KVM/ARM
- Yield CPU when guest executes WFE to speed up CPU overcommit
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSZ5NVAAoJEEtpOizt6ddyEJgH+wWw6KWqHlParb+rf04cqCQV
Fj3euz+SpYr2U2u0RimgkmeahUiGUhnlBSSH+tkLmt1if6nLawBJbUcIhaZMVdv+
cvS6k+NtK7ibwPOyFeoZCS8taEbVDut2YgrtRKbne6QDLRYBEXFtpY8o6ptLoSu4
ifQCF0FZyElCGLylSxFt9GsK+LjNjQWatVrzoHap9d58u2bma6GYwr4mEzVMHms7
REtTvpwWgsDR5C/69aG8wE4cpJZALH3OeCgy6AccdzTLaQWWpK2YLWz8AFOvoYx6
EsFmBFHZYcuwN+fv2jILgA3Is1oWwqI6k5lL+N3g/oTNNALDSWnfiJkXypJsfow=
=2Ijm
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-3.13-2' of git://git.linaro.org/people/cdall/linux-kvm-arm into kvm-queue
Updates for KVM/ARM, take 2 including:
- Transparent Huge Pages and hugetlbfs support for KVM/ARM
- Yield CPU when guest executes WFE to speed up CPU overcommit
From Kukjin Kim, these are device-tree updates for Exynos. Among the changes:
- add MIPI PHY node for exynos4
- update regulator for origen and exynos5250-arndale
- add support HDMI for exynos5250, exynos5420
* commit '93457b9cb980ffeeef020c3bcd99065c3807619b':
ARM: dts: Add HDMI related I2C nodes for Arndale board
ARM: dts: enable hdmi subsystem for exynos5420 smdk board
ARM: dts: add dt nodes for hdmi subsystem for exynos5420
ARM: dts: add i2c device nodes for Exynos5420
ARM: dts: add clocks to hdmi dt node for exynos5250
ARM: dts: add mixer clocks to mixer node for Exynos5250
of/documentation: update with clock information for exynos hdmi subsystem
ARM: dts: Disable Exynos5250 I2S controllers by default
ARM: dts: Add reg property to regulator nodes in exynos5250-arndale
ARM: dts: Add fixed voltage regulator to simple bus for origen
ARM: dts: Add MIPI PHY node to exynos4.dtsi
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WYJE
-----END PGP SIGNATURE-----
Merge tag 's3c24xx-dma' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/drivers
From Kukjin Kim, this branch adds device-tree support to the DMA controller
on the older Samsung SoCs. It also adds support for one of the missing SoCs
in the family (2410).
The driver has been Ack:ed by Vinod Koul, but is merged through here due
to dependencies with platform code.
* tag 's3c24xx-dma' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C24XX: add dma pdata for s3c2410, s3c2440 and s3c2442
dmaengine: s3c24xx-dma: add support for the s3c2410 type of controller
ARM: S3C24XX: Fix possible dma selection warning
ARM: SAMSUNG: set s3c24xx_dma_filter for s3c64xx-spi0 device
ARM: S3C24XX: add platform-devices for new dma driver for s3c2412 and s3c2443
dmaengine: add driver for Samsung s3c24xx SoCs
ARM: S3C24XX: number the dma clocks
+ Linux 3.12-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>
- remove unnecessary config options and header inclusions
- use CONFIG_ARCH_S3C64XX instead of PLAT_S3C64XX
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=jVqg
-----END PGP SIGNATURE-----
Merge tag 'samsung-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup
From Kukjin Kim:
Samsung Cleanup for v3.13
- remove unnecessary config options and header inclusions
- use CONFIG_ARCH_S3C64XX instead of PLAT_S3C64XX
* tag 'samsung-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: remove CONFIG_MACH_EXYNOS[4, 5]_DT config options
ARM: EXYNOS: remove unnecessary header inclusions from exynos4/5 dt machine file
ARM: S3C64XX: Kill CONFIG_PLAT_S3C64XX
ASoC: samsung: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
s3c-camif: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
gpio: samsung: Use CONFIG_ARCH_S3C64XX to check for S3C64XX support
ARM: S3C64XX: Move if ARCH_S3C64XX statement into mach-s3c64xx
Signed-off-by: Olof Johansson <olof@lixom.net>
and adding SSP/SPI devices to the device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJSYYhgAAoJEEEQszewGV1zHx8QAJwXuxowqE5kqlq2gRA8R420
yqEaP5PX/34kVzuAAkhDosqtEEmcCvKtC+OhTAlyds78fF6iSvecg0YdiTQ9vzNf
3khW97pvCjIOyDVfKST1gjC0HVwxAVNuA9b/LhORB/3Hi3CzvRJ5PhXHf3rqPUS6
9HN9/Y4h4zPYU+Wk3PIBAmfmg79TA7pR4l3sF2Rf63CeYC5d3Zv/x/SEAYZ2Ilqo
TTZc4zNDUznqTnm9wM8C/FY/cg7fa3q2vlXyF1rcHle6uNAvWOFxc7nuir3nF0Qu
NNPUk7LEAwsdQ5eK1XybNGBofSJYzsNRjWq4Lp3/DytTBH6gUKE/CUQ4A4ujJYEY
8zhQV3wMSrs0cVhoubu9rPolVl5dGb/dtambZvwtL6RcDBBaUesixrDmLHIkTSqi
u7WZ1kMhb5txQKmn+oNmu3qzxEXYF/mp5mYzOnurGfJ/DFTfc+mfui1WUq1ybCTz
Z2yCku9iKyeBpyw2Kt9PVJ+qk2JWEP/c3MddJtw5YvWopkol9avkhXUnjCpSTY3R
aO3nwusXaYSPSNZZAVkHrDruoEafAWktITEiCTWURQFd5OSYiUcHVqJ32XwOnwWD
9wtZMLhnPkRgM4CpkzvYclUyY6Wuyy2mhd6PO305mBqQp8GZIm5dMggGctaHNi1H
pVJ2WpQkn8mMekoI716u
=p/3j
-----END PGP SIGNATURE-----
Merge tag 'ux500-dt-for-v3.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From Linus Walleij:
Five incremental device tree patches around the clock handling,
and adding SSP/SPI devices to the device tree.
* tag 'ux500-dt-for-v3.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: register all SSP and SPI blocks
ARM: ux500: fix I2C4 clock bit
ARM: ux500: fix clock for GPIO blocks 6 and 7
clk: ux500: fix erroneous bit assignment
ARM: ux500: fix clock for GPIO block 8
Signed-off-by: Olof Johansson <olof@lixom.net>
This DT series sees the introduction of the cubietruck DT, plus the addition of
the i2c controller for the A20 based boards, and of the Security ID found in
all the Allwinner SoCs but the A31.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJSYW3yAAoJEBx+YmzsjxAg5HoP/jCsw/QQ+Po6fvf3h0C1PLQs
JKPredNJwaAjv436zawhlOZWSm6kj0qI6EKshtFUnOm436Ie5vAV/HthlI3vImBs
xtnaCCphfBRB/9MpjOaqQILBMGiVFbI5Rfsx1VgY3lOnLG7yp87PLJ/2d1h+drKF
21LgjkDtc5zP1X+42bNF+oK0UDVkWJUxPxcm5JlwYQUFUBoE/FIqUKU5LM5/fsXE
26eeFPQnf2zqW0Bxx09Jd8wKdRWXLM1+JVlgH+NG2KPL3g5kFbaHHfElzMgsal81
JKk4qmefGcfzLyJAUPTV8B002o4FKGiwaLZdULDVAXFQcJP6AONTCW9cbNAqTZdE
6wSwvo01LOFaAXqJD1HB56ZCASc4qXaoq0vK4Jdefjjb7x4MDeNPD89L6sK21TaQ
atHtFPvzElPyQw5kfJpBypAwSB9+iCk78L7OO2g6bAKvR9WPS2QWr+K7ipuILooT
c9QX9ww9wIMg8whumKsKGkGreSi075FXoSyhF7NEz3TR8P7ghCUdFuK5pdLhiXXi
W/ZejujJDMDjuJtW8VblXFBNa6VrPab51jp5fs+k4IJWDcLbnSpD5PbetMZRNlce
DYAPqhmlx96R2bwzr1Cq+7Ww+7G+xd1HgTh5wZElm2JtBGHVkXOEZbb85stZ5bA8
i4/5xcEPIFExI69Dj9LV
=Qc5W
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-3.13' of https://github.com/mripard/linux into next/dt
From Maxime Ripard:
Allwinner sunXi SoCs device tree changes for 3.13
This DT series sees the introduction of the cubietruck DT, plus the addition of
the i2c controller for the A20 based boards, and of the Security ID found in
all the Allwinner SoCs but the A31.
* tag 'sunxi-dt-for-3.13' of https://github.com/mripard/linux:
ARM: sunxi: dts: Add support for the cubieboard3, the CubieTruck
ARM: sun7i: olinuxino-micro: Enable the I2C controllers
ARM: sun7i: cubieboard2: Enable the I2C controllers
ARM: sun7i: Add the pin muxing options for the I2C controllers
ARM: sun7i: Enable the I2C controllers
ARM: sunxi: dt: Add sunxi-sid to dts for sun4i, sun5i and sun7i
Signed-off-by: Olof Johansson <olof@lixom.net>
* pm-cpufreq: (167 commits)
cpufreq: create per policy rwsem instead of per CPU cpu_policy_rwsem
intel_pstate: Add Baytrail support
intel_pstate: Refactor driver to support CPUs with different MSR layouts
cpufreq: Implement light weight ->target_index() routine
PM / OPP: rename header to linux/pm_opp.h
PM / OPP: rename data structures to dev_pm equivalents
PM / OPP: rename functions to dev_pm_opp*
cpufreq / governor: Remove fossil comment
cpufreq: exynos4210: Use the common clock framework to set APLL clock rate
cpufreq: exynos4x12: Use the common clock framework to set APLL clock rate
cpufreq: Detect spurious invocations of update_policy_cpu()
cpufreq: pmac64: enable cpufreq on iMac G5 (iSight) model
cpufreq: pmac64: provide cpufreq transition latency for older G5 models
cpufreq: pmac64: speed up frequency switch
cpufreq: highbank-cpufreq: Enable Midway/ECX-2000
exynos-cpufreq: fix false return check from "regulator_set_voltage"
speedstep-centrino: Remove unnecessary braces
acpi-cpufreq: Add comment under ACPI_ADR_SPACE_SYSTEM_IO case
cpufreq: arm-big-little: use clk_get instead of clk_get_sys
cpufreq: exynos: Show a list of available frequencies
...
Conflicts:
drivers/devfreq/exynos/exynos5_bus.c
* pm-cpuidle:
ARM: AT91: DT: pm: Select ram controller standby based on DT
ARM: AT91: pm: Factorize standby function
ARM: at91: cpuidle: Move driver to drivers/cpuidle
ARM: at91: cpuidle: Convert to platform driver
ARM: ux500: cpuidle: fix section mismatch
ARM: zynq: cpuidle: convert to platform driver
ARM: zynq: cpuidle: Remove useless compatibility string
drivers: cpuidle: rename ARM big.LITTLE driver config and makefile entries
ARM: EXYNOS: convert cpuidle driver to be a platform driver
intel_idle: mark some functions with __init tag
intel_idle: mark states tables with __initdata tag
intel_idle: shrink states tables
Currently, the prototype of cpufreq_drivers target routines is:
int target(struct cpufreq_policy *policy, unsigned int target_freq,
unsigned int relation);
And most of the drivers call cpufreq_frequency_table_target() to get a valid
index of their frequency table which is closest to the target_freq. And they
don't use target_freq and relation after that.
So, it makes sense to just do this work in cpufreq core before calling
cpufreq_frequency_table_target() and simply pass index instead. But this can be
done only with drivers which expose their frequency table with cpufreq core. For
others we need to stick with the old prototype of target() until those drivers
are converted to expose frequency tables.
This patch implements the new light weight prototype for target_index() routine.
It looks like this:
int target_index(struct cpufreq_policy *policy, unsigned int index);
CPUFreq core will call cpufreq_frequency_table_target() before calling this
routine and pass index to it. Because CPUFreq core now requires to call routines
present in freq_table.c CONFIG_CPU_FREQ_TABLE must be enabled all the time.
This also marks target() interface as deprecated. So, that new drivers avoid
using it. And Documentation is updated accordingly.
It also converts existing .target() to newly defined light weight
.target_index() routine for many driver.
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Russell King <linux@arm.linux.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Since Operating Performance Points (OPP) functions are specific
to device specific power management, be specific and rename opp.h
to pm_opp.h
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since Operating Performance Points (OPP) data structures are specific
to device specific power management, be specific and rename opp_* data
structures in OPP library with dev_pm_opp_* equivalent.
Affected structures are:
struct opp
enum opp_event
Minor checkpatch warning resulting of this change was fixed as well.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since Operating Performance Points (OPP) functions are specific to
device specific power management, be specific and rename opp_*
accessors in OPP library with dev_pm_opp_* equivalent.
Affected functions are:
opp_get_voltage
opp_get_freq
opp_get_opp_count
opp_find_freq_exact
opp_find_freq_floor
opp_find_freq_ceil
opp_add
opp_enable
opp_disable
opp_get_notifier
opp_init_cpufreq_table
opp_free_cpufreq_table
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch moves the handling of the chip's enable pin from the board
code into the driver. It also updates all board-code files using the
driver to incorporate this change.
This is needed for device tree support of the enable pin.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
There's really only one bugfix in this branch, which is a fix for timers on
the integrator platform. Since Linus Walleij is resurrecting support for
the platform it seems valuable to get the fix into 3.12 even though the
regression has been around a while.
The rest are a handful of maintainers updates. If you prefer to hold those
until 3.13 then just merge the first patch on the branch which is the fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7MQ0
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"There's really only one bugfix in this branch, which is a fix for
timers on the integrator platform. Since Linus Walleij is
resurrecting support for the platform it seems valuable to get the fix
into 3.12 even though the regression has been around a while.
The rest are a handful of maintainers updates. If you prefer to hold
those until 3.13 then just merge the first patch on the branch which
is the fix"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: Add maintainers entry for Rockchip SoCs
MAINTAINERS: Tegra updates, and driver ownership
MAINTAINERS: ARM: mvebu: add Sebastian Hesselbarth
ARM: integrator: deactivate timer0 on the Integrator/CP
This branch includes:
* SoC fuse values are used as device randomness at boot.
* Initial support for the Tegra124 SoC is added. When coupled with an
appropriate clock driver, which should also be merged for 3.13, we are
able to boot to user-space using an initrd.
* The powergate code gains support for Tegra114.
This branch is based on previous pull request tegra-for-3.13-cleanup.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSYbeKAAoJEMzrak5tbycx3tIQAKmPgax0hf4te1f1Z5mNpafK
07ri4iuGiBSflfXsz+WL5WvfLBr0ONB6q5sqwrUIYk1iCxkNT3uXS/Z67V6YobF/
U3URwpM2/p09k7LGbP/TqnprwMYzFDaPNpJBBAYh++dzSD9QzcB5CJ6EWGtP0OnL
FvtBF2HIbCRlSqUlOVDSHXwyf/y3jqSg3XSPOYeqPWYF/a7WQGf/wXSgAZusohB+
K93gMmHp4KFgoW1udqOCbC7kzl0B96+nkiAq55JL9WbuJ6V56xmrf2+J9rcd3c4x
o5+y8mRd2Zp1Llk+LTFHAmBtdO/aWhP286kPCKapsneKsi268lciR82/QEMvday8
iBbcnxK1bwwKJTLW4HJI6u+aKrxF0uk9usdeJw5wFEh7pMD0Zvh9D02S34Qdu5mu
DoSu5xSLZ4pb3ChPK5IH1cKWKOGM0pR/mWxkUVfg9f0E4yenFepS9+2zP40xEz3W
CiLbLdmoAExiZkqvadYgOnA47u4z57NByPyKEeH0jMCbX0M39QCg+DDBRZrjt0OV
XJrToVdZYk7syDxW94nnFWKNCJT+oqpn3j8xUAz7OplEFEZ3My0Ndz1vaY5glv6d
CuylPtx5+GmEZJH8Lynh8tBAE20+ngbqMDo7awnl4U/+XsNgqli88GZEwHD+XxWp
/45R36Fm/MyA8hD/ymM5
=2btl
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.13-soc-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/soc
From Stephen Warren:
ARM: tegra: core SoC support changes for 3.13
This branch includes:
* SoC fuse values are used as device randomness at boot.
* Initial support for the Tegra124 SoC is added. When coupled with an
appropriate clock driver, which should also be merged for 3.13, we are
able to boot to user-space using an initrd.
* The powergate code gains support for Tegra114.
This branch is based on previous pull request tegra-for-3.13-cleanup.
* tag 'tegra-for-3.13-soc-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ARM: tegra: Add Tegra114 powergate support
ARM: tegra: Constify list of CPU domains
ARM: tegra: Remove duplicate powergate defines
ARM: tegra: add LP1 support code for Tegra124
ARM: tegra: re-calculate the LP1 data for Tegra30/114
ARM: tegra: enable CPU idle for Tegra124
ARM: tegra: make tegra_resume can work with current and later chips
ARM: tegra: CPU hotplug support for Tegra124
ARM: tegra: add PMC compatible value for Tegra124
ARM: tegra: add Tegra124 SoC support
ARM: tegra: add fuses as device randomness
ARM: tegra: fix ARCH_TEGRA_114_SOC select sort order
ARM: tegra: make tegra_init_fuse() __init
ARM: tegra: remove much of iomap.h
ARM: tegra: move resume vector define to irammap.h
ARM: tegra: delete gpio-names.h
ARM: tegra: delete stale header content
ARM: tegra: remove common.c
ARM: tegra: split tegra_pmc_init() in two
Signed-off-by: Kevin Hilman <khilman@linaro.org>
This is similar to what it is done on X86: biovecs are prevented from merging
otherwise every dma requests would be forced to bounce on the swiotlb buffer.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Changes in v7:
- remove the extra autotranslate check in biomerge.c.
Introduce xen_dma_map_page, xen_dma_unmap_page,
xen_dma_sync_single_for_cpu and xen_dma_sync_single_for_device.
They have empty implementations on x86 and ia64 but they call the
corresponding platform dma_ops function on arm and arm64.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Changes in v9:
- xen_dma_map_page return void, avoid page_to_phys.
Final conversions to configfs for mass storage, acm_ms, and
multi gadgets.
MUSB should now work out of the box on AM335x-based boards
(beagle bone white and black) with DMA thanks to Sebastian's
work.
We can now enable VERBOSE_DEBUG on builds of drivers/usb/gadget/
by selecting CONFIG_USB_GADGET_VERBOSE.
s3c-hsotg got quite a few non-critical fixes but also learned
a few new tricks (isochronous transfers, multi count support).
The Marvel USB3 Controller driver got a memory leak fix.
devm_usb_get_phy() learned not to return NULL, ever.
Other than these patches, we have the usual set of cleanups
ranging from removal of unnecessary *_set_drvdata() to using
SIMPLE_DEV_PM_OPS.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=LDY7
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.13
Final conversions to configfs for mass storage, acm_ms, and
multi gadgets.
MUSB should now work out of the box on AM335x-based boards
(beagle bone white and black) with DMA thanks to Sebastian's
work.
We can now enable VERBOSE_DEBUG on builds of drivers/usb/gadget/
by selecting CONFIG_USB_GADGET_VERBOSE.
s3c-hsotg got quite a few non-critical fixes but also learned
a few new tricks (isochronous transfers, multi count support).
The Marvel USB3 Controller driver got a memory leak fix.
devm_usb_get_phy() learned not to return NULL, ever.
Other than these patches, we have the usual set of cleanups
ranging from removal of unnecessary *_set_drvdata() to using
SIMPLE_DEV_PM_OPS.
Signed-of-by: Felipe Balbi <balbi@ti.com>
dpll4_m3_ck and dpll4_m4_ck have divider bit fields which are 6 bits
wide. However, only values from 1 to 32 are allowed. This means we have
to add a divider tables and list the dividers explicitly.
I believe the same issue is there for other dpll4_mx_ck clocks, but as
I'm not familiar with them, I didn't touch them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Set CLK_SET_RATE_PARENT flag for dss1_alwon_fck_3430es2,
dss1_alwon_fck_3430es1 and dpll4_m4x2_ck so that the DSS's fclk can be
configured without the need to get the parent's parent of the fclk.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Set CLK_SET_RATE_PARENT flag for dss_dss_clk so that the DSS's fclk can
be configured without the need to get the parent of the fclk.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Several architectures open code effectively the same code block for
finding and mapping PCI irqs. This patch consolidates it down to a
single function.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Replace some instances of of_irq_map_one()/irq_create_of_mapping() and
of_irq_to_resource() by the simpler equivalent irq_of_parse_and_map().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
[grant.likely: resolved conflicts with core code renames]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
This patch extends the DT selftest code with some test cases for the
interrupt parsing functions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
All the callers of irq_create_of_mapping() pass the contents of a struct
of_phandle_args structure to the function. Since all the callers already
have an of_phandle_args pointer, why not pass it directly to
irq_create_of_mapping()?
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
struct of_irq and struct of_phandle_args are exactly the same structure.
This patch makes the kernel use of_phandle_args everywhere. This in
itself isn't a big deal, but it makes some follow-on patches simpler.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The OF irq handling code has been overloading the term 'map' to refer to
both parsing the data in the device tree and mapping it to the internal
linux irq system. This is probably because the device tree does have the
concept of an 'interrupt-map' function for translating interrupt
references from one node to another, but 'map' is still confusing when
the primary purpose of some of the functions are to parse the DT data.
This patch renames all the of_irq_map_* functions to of_irq_parse_*
which makes it clear that there is a difference between the parsing
phase and the mapping phase. Kernel code can make use of just the
parsing or just the mapping support as needed by the subsystem.
The patch was generated mechanically with a handful of sed commands.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
DMA mapping permissions were being derived from pgprot_kernel directly
without using PAGE_KERNEL. This causes them to be marked with executable
permission, which is not what we want. Fix this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Conflicts:
drivers/net/usb/qmi_wwan.c
include/net/dst.h
Trivial merge conflicts, both were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Architectures which support CONFIG_PARPORT_PC should select
ARCH_MIGHT_HAVE_PC_PARPORT.
Signed-off-by: Mark Salter <msalter@redhat.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: linux-arm-kernel@lists.infradead.org
The CODEC power supplies should be looked up on the Arizona device as
they will be created here by device tree also update the only user of
non-device tree bindings.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Armada 370/XP SoC has a clock provider called "Core Divider",
that is derived from a fixed 2 GHz PLL clock.
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Armada 370/XP SoCs have a 2 GHz fixed PLL that is used to feed
other clocks. This commit adds a DT representation of this clock
through a fixed-clock compatible node.
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add OPP table to OMAP5/DRA7
Add support for Newflow NanoBone board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=inDp
-----END PGP SIGNATURE-----
Merge tag 'for_3.13_super_late/dts_signed' of git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt into omap-for-v3.13/dt
Add a lot of N900 nodes
Add OPP table to OMAP5/DRA7
Add support for Newflow NanoBone board
When the omap5-evm.dts file has been renamed to omap5-uevm.dts and the sEVM
support got deprecated in favor of uEVM (or Panda5) the content was not
validated.
Panda5 does not have support for digital microphones so remove the pinmux
section for it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
When the omap5-evm.dts file has been renamed to omap5-uevm.dts and the sEVM
support got deprecated in favor of uEVM (or Panda5) the content was not
validated.
On uEVM the twl6040 reset GPIO is from gpio5_141 and not via gpio5_145, which
was the case in sEVM.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This patch adds support for Nokia N900 TLV320AIC3X chips.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add RX51_LCD_RESET_GPIO pin mux information to
display.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This patch adds supports for Nokia N900 NAND memory.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add regulator names and voltage information to
the Nokia N900 DTS file.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The twl4030.dtsi is missing some regulators. This patch adds
the missing ones and orders the regulators alphabetically.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add device tree node for the GPIO keys provided by the
N900 board. This is a simple conversion of the existing
board code.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add pin muxing support for the Nokia N900 i2c controllers.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Pull networking fixes from David Miller:
"Sorry I let so much accumulate, I was in Buffalo and wanted a few
things to cook in my tree for a while before sending to you. Anyways,
it's a lot of little things as usual at this stage in the game"
1) Make bonding MAINTAINERS entry reflect reality, from Andy
Gospodarek.
2) Fix accidental sock_put() on timewait mini sockets, from Eric
Dumazet.
3) Fix crashes in l2tp due to mis-handling of ipv4 mapped ipv6
addresses, from François CACHEREUL.
4) Fix heap overflow in __audit_sockaddr(), from the eagle eyed Dan
Carpenter.
5) tcp_shifted_skb() doesn't take handle FINs properly, from Eric
Dumazet.
6) SFC driver bug fixes from Ben Hutchings.
7) Fix TX packet scheduling wedge after channel change in ath9k driver,
from Felix Fietkau.
8) Fix user after free in BPF JIT code, from Alexei Starovoitov.
9) Source address selection test is reversed in
__ip_route_output_key(), fix from Jiri Benc.
10) VLAN and CAN layer mis-size netlink attributes, from Marc
Kleine-Budde.
11) Fix permission checks in sysctls to use current_euid() instead of
current_uid(). From Eric W Biederman.
12) IPSEC policies can go away while a timer is still pending for them,
add appropriate ref-counting to fix, from Steffen Klassert.
13) Fix mis-programming of FDR and RMCR registers on R8A7740 sh_eth
chips, from Nguyen Hong Ky and Simon Horman.
14) MLX4 forgets to DMA unmap pages on RX, fix from Amir Vadai.
15) IPV6 GRE tunnel MTU upper limit is miscalculated, from Oussama
Ghorbel.
16) Fix typo in fq_change(), we were assigning "initial quantum" to
"quantum". From Eric Dumazet.
17) Set a more appropriate sk_pacing_rate for non-TCP sockets, otherwise
FQ packet scheduler does not pace those flows properly. Also from
Eric Dumazet.
18) rtlwifi miscalculates packet pointers, from Mark Cave-Ayland.
19) l2tp_xmit_skb() can be called from process context, not just softirq
context, so we must always make sure to BH disable around it. From
Eric Dumazet.
20) On qdisc reset, we forget to purge the RB tree of SKBs in netem
packet scheduler. From Stephen Hemminger.
21) Fix info leak in farsync WAN driver ioctl() handler, from Dan
Carpenter and Salva Peiró.
22) Fix PHY reset and other issues in dm9000 driver, from Nikita
Kiryanov and Michael Abbott.
23) When hardware can do SCTP crc32 checksums, we accidently don't
disable the csum offload when IPSEC transformations have been
applied. From Fan Du and Vlad Yasevich.
24) Tail loss probing in TCP leaves the socket in the wrong congestion
avoidance state. From Yuchung Cheng.
25) In CPSW driver, enable NAPI before interrupts are turned on, from
Markus Pargmann.
26) Integer underflow and dual-assignment in YAM hamradio driver, from
Dan Carpenter.
27) If we are going to mangle a packet in tcp_set_skb_tso_segs() we must
unclone it. This fixes various hard to track down crashes in
drivers where the SKBs ->gso_segs was changing right from underneath
the driver during TX queueing. From Eric Dumazet.
28) Fix the handling of VLAN IDs, and in particular the special IDs 0
and 4095, in the bridging layer. From Toshiaki Makita.
29) Another info leak, this time in wanxl WAN driver, from Salva Peiró.
30) Fix race in socket credential passing, from Daniel Borkmann.
31) WHen NETLABEL is disabled, we don't validate CIPSO packets properly,
from Seif Mazareeb.
32) Fix identification of fragmented frames in ipv4/ipv6 UDP
Fragmentation Offload output paths, from Jiri Pirko.
33) Virtual Function fixes in bnx2x driver from Yuval Mintz and Ariel
Elior.
34) When we removed the explicit neighbour pointer from ipv6 routes a
slight regression was introduced for users such as IPVS, xt_TEE, and
raw sockets. We mix up the users requested destination address with
the routes assigned nexthop/gateway. From Julian Anastasov and
Simon Horman.
35) Fix stack overruns in rt6_probe(), the issue is that can end up
doing two full packet xmit paths at the same time when emitting
neighbour discovery messages. From Hannes Frederic Sowa.
36) davinci_emac driver doesn't handle IFF_ALLMULTI correctly, from
Mariusz Ceier.
37) Make sure to set TCP sk_pacing_rate after the first legitimate RTT
sample, from Neal Cardwell.
38) Wrong netlink attribute passed to xfrm_replay_verify_len(), from
Steffen Klassert.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (152 commits)
ax88179_178a: Add VID:DID for Samsung USB Ethernet Adapter
ax88179_178a: Correct the RX error definition in RX header
Revert "bridge: only expire the mdb entry when query is received"
tcp: initialize passive-side sk_pacing_rate after 3WHS
davinci_emac.c: Fix IFF_ALLMULTI setup
mac802154: correct a typo in ieee802154_alloc_device() prototype
ipv6: probe routes asynchronous in rt6_probe
netfilter: nf_conntrack: fix rt6i_gateway checks for H.323 helper
ipv6: fill rt6i_gateway with nexthop address
ipv6: always prefer rt6i_gateway if present
bnx2x: Set NETIF_F_HIGHDMA unconditionally
bnx2x: Don't pretend during register dump
bnx2x: Lock DMAE when used by statistic flow
bnx2x: Prevent null pointer dereference on error flow
bnx2x: Fix config when SR-IOV and iSCSI are enabled
bnx2x: Fix Coalescing configuration
bnx2x: Unlock VF-PF channel on MAC/VLAN config error
bnx2x: Prevent an illegal pointer dereference during panic
bnx2x: Fix Maximum CoS estimation for VFs
drivers: net: cpsw: fix kernel warn during iperf test with interrupt pacing
...
Add DT OPP table for DRA7xx family of devices. This data is decoded by
OF with of_init_opp_table() helper function.
The data is based on DRA75x, DRA74x Data Manual revision F (Sept 2013).
TODO: add OPP_HIGH after AVS-Class0 is functional
NOTE: The voltage and frequency values work well only on NOM samples
and it is mandatory to use ABB/AVS Class 0 support for all OPPs.
Clock nodes are pending clock node alignment.
[nm@ti.com: cleanups and rebase to latest]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add DT OPP table for OMAP54xx family of devices. This data is
decoded by OF with of_init_opp_table() helper function.
The data is based on OMAP543x ES2.0 DM Operating Condition Addendum
Version 0.6(April 2013)
NOTE: The voltage and frequency values work well only on NOM samples
and are supposed to work properly only with ABB/AVS for ALL OPPs.
TODO: Add SPEED BIN OPP after ABB and AVS support so the cpufreq works
on all samples seamlessly. Clock node is pending alignment for clock
dts conversion
[nm@ti.com: sync to latest and fixes]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
regulator smps123 supply from Palmas PMIC powers CPU0 on OMAP5uEVM.
Based on a patch by J Keerthy <j-keerthy@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
With OMAP3+ and AM33xx supported SoC having defined CPU device tree
entries with operating-points and clock nodes defined, we can now use
the SoC generic cpufreq-cpu0 driver by registering appropriate device.
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM335x, AM43xx, OMAP5 and DRA7 have missing late init hook. Introduce
SoC specific hook with a call to OMAP2+ generic lateinit hook. This
allows the generic late initializations such as cpufreq hooks to be
active.
Based on out-of-tree patches that need to be introduced in
mainline, this introduction allows us to provide the foundation for
further SoC specific features as they are developed.
Cc: Benoit Cousson <bcousson@baylibre.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP3+ supports both device tree and non-device tree boot.
Device tree bindings for OMAP3+ is supposed to be added via dts following:
Documentation/devicetree/bindings/power/opp.txt
Since we now have device tree entries for OMAP3+ cpu OPPs,
The current code wrongly adds duplicate OPPs. So, dont register OPPs
when booting using device tree.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The KVM PSCI code blindly assumes that vcpu_id and MPIDR are
the same thing. This is true when vcpus are organized as a flat
topology, but is wrong when trying to emulate any other topology
(such as A15 clusters).
Change the KVM PSCI CPU_ON code to look at the MPIDR instead
of the vcpu_id to pick a target CPU.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Now that the KVM/arm code knows about affinity, remove the hard
limit of 4 vcpus per VM.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The L2CTLR register contains the number of CPUs in this cluster.
Make sure the register content is actually relevant to the vcpu
that is being configured by computing the number of cores that are
part of its cluster.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
In order to be able to support more than 4 A7 or A15 CPUs,
we need to fix the MPIDR computing to reflect the fact that
both A15 and A7 can only exist in clusters of at most 4 CPUs.
Fix the MPIDR computing to allow virtual clusters to be exposed
to the guest.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Correct mcspi pin descriptions to match corresponding node name and
add chip select number to be consistent with OMAP5 TRM.
Signed-off-by: Eric Witcher <ewitcher@mindspring.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Control module is not usb specific.
Changes the label to usb_ctrl_mod.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
am33xx has a INTC_PENDING_IRQ3 register that is not checked for pending
interrupts. This patch adds AM33XX to the ifdef of SOCs that have to
check this register.
Cc: stable@vger.kernel.org
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM43x has 224 interrupts and 7 banks, make it as maximum values. Keep
default values as earlier, if am43x is detected, update interrupts and
banks accordingly.
Also AM43x has only one cpu, ensure that clearing bitmask at wakeupgen
is done only for the single existing cpu, existing code assumes that
there are two cpu's.
If bitmask is cleared in wakeupgen for the nonexistent second cpu,
an imprecise abort happens as soon as Kernel switches to user space.
It was rootcaused by Sekhar Nori <nsekhar@ti.com>.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
NanoBone Specification:
-----------------------
CPU:
TI AM335x
Memory:
256MB DDR3
128MB NOR flash
128KB FRAM
Ethernet:
2 x 10/100 connected to SMSC LAN8710 PHY
USB:
1 x USB2.0 Type A
I2C:
2Kbit EEPROM (Microchip 24AA02)
RTC (Maxim DS1338)
GPIO Expander (Microchip MCP23017)
Expansion connector:
6 x UART
1 x MMC/SD
1 x USB2.0
Signed-off-by: Mark Jackson <mpfj@newflow.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Looks like omap3 is still relying on hwmod data for some basic
device tree information. Let's add the information to omap3.dtsi
so we can remove the related hwmod data once omap3 is DT only.
Acked-by: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Provide alias to allow ordering the i2c devices correctly.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Currently, on OMAP5, i2c1 and i2c5 defer probe due to pinctrl
dependencies. This changes the i2c ID each bus is registered with in
i2c-dev interface. As a result of this, many userspace tools break and
there is no consistent manner to fix the same if the i2c dev interface
have no consistent numbering.
Since this could happen for other OMAP derivatives, provide i2c alias
for all OMAP3+ SoCs to allow ordering the i2c devices correctly.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Add nodes for McASP0 and McASP1 for AM43xx.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Several configurations are selecting errata 798181 without SMP
being selected. This causes a warning from Kconfig:
warning: (ARCH_HIGHBANK && ARCH_KEYSTONE && SOC_OMAP5 && ARCH_TEGRA_114_SOC) selects ARM_ERRATA_798181 which has unmet direct dependencies (CPU_V7 && SMP)
The dependencies are compile time dependencies; select violates these,
resulting in:
arch/arm/kernel/built-in.o: In function `setup_processor':
psci.c:(.init.text+0x808): undefined reference to `erratum_a15_798181_init'
at build time. Fix this by fixing the select statements for Tegra and
Highbank.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The imx6sl low power mode implementation inherits imx6q/dl one,
and pm-imx6q.c can just work for imx6sl with some minor updates.
Let's enable imx6sl suspend support by reusing pm-imx6q.c and use
cpu_is_imxXX() to handle the those minor differences between imx6sl
and imx6q/dl.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
There is a defect in imx6 LPM design. When SW tries to enter low power
mode with following sequence, the chip will enter low power mode before
A9 CPU execute WFI instruction:
1. Set CCM_CLPCR[1:0] to 2'b00;
2. ARM CPU enters WFI;
3. ARM CPU wakeup from an interrupt event, which is masked by GPC or not
visible to GPC, such as interrupt from local timer;
4. Set CCM_CLPCR[1:0] to 2'b01 or 2'b10;
5. ARM CPU execute WFI.
Before the last step, the chip will enter WAIT mode if CCM_CLPCR[1:0] is
set to 2'b01, or enter STOP mode if CCM_CLPCR[1:0] is set to 2'b10.
The patch implements a recommended workaround for this issue.
1. SW triggers irq #32(IOMUX) to be always pending manually by setting
IOMUX_GPR1_GINT bit;
2. SW should then unmask it in GPC before setting CCM LPM;
3. SW should mask it right after CCM LPM is set (bit0-1 of CCM_CLPCR).
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The WB and RBC configuration calls are currently made from
imx6q_set_lpm() for WAIT_CLOCKED and WAIT_UNCLOCKED mode with a simple
state tracking. This becomes unnecessary since we can make the calls
from imx6q_pm_enter() directly now for suspend.
More importantly, the current call of imx6q_enable_wb() from
imx6q_set_lpm() is buggy. The CLPCR register bits configured by
imx6q_enable_wb() will get lost, because imx6q_set_lpm() caches the same
register and write it back at the end of the function. That's why the
imx6dl suspend/resume does not work currently - the wakeup from suspend
triggers a reset on imx6dl.
Moves the WB and RBC calls into imx6q_pm_enter() to save the state
tracking and fixes above bug, so that suspend/resume can start working
on imx6dl.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The LPM (Low Power Mode) code that currently sits in imx6q clock driver
will be reused by imx6sl. Let's move it into pm-imx6q.c, so that we
can keep clock driver SoC specific and reuse pm-imx6q.c on imx6sl.
In order to avoid adding another ioremap for CCM block,
imx6q_pm_set_ccm_base() is created to let clock driver set up ccm_base
for pm code.
During the move, the unused CCGR macros get removed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since commit 70dc8a4 (checkpatch: warn when using extern with function
prototypes in .h files), we will get checkpatch warning when updating
common.h following the existing convention which has extern for function
prototypes.
Let's change the convention to not use extern with function prototypes
in this header.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
From hotplug stress test result, resetting core during enable/disable
operation can improve cpu hotplug stability. So let's set
SRC reset bit in imx_enable_cpu() for the core when its enable bit is
accessed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
When imx_cpu_die() is being called, the cpu should never return from the
call but just in WFI and wait for hardware to take it down. So let's
do cpu_do_idle() repeatly in the call. Doing this help improve the
relibility of hotplug operation.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This is very useful for detecting 'circular locking dependency' issues.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Having CONFIG_DEBUG_GPIO=y leads to several debug messages polluting kernel log:
[ 0.580325] of_get_named_gpio_flags: can't parse gpios property of node '/regulators/3p3v[0]'
[ 0.581185] 3P3V: 3300 mV
[ 0.584827] of_get_named_gpio_flags exited with status 124
[ 0.585852] vddio-sd0: 3300 mV
[ 0.590023] of_get_named_gpio_flags exited with status 79
[ 0.590770] fec-3v3: 3300 mV
[ 0.594805] of_get_named_gpio_flags exited with status 105
[ 0.595491] usb0_vbus: 5000 mV
[ 0.599687] of_get_named_gpio_flags exited with status 104
[ 0.600380] usb1_vbus: 5000 mV
[ 0.604463] of_get_named_gpio_flags exited with status 126
[ 0.605153] lcd-3v3: 3300 mV
[ 0.608970] of_get_named_gpio_flags exited with status 77
Turn this option off, as these messages are not really useful for normal usage.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The imx6q_restart() works fine with normal reboot but will run into
problem with emergency reboot like sysrq-b. In that case, of_iomap()
gets called from interrupt context and hence triggers the BUG_ON in
__get_vm_area_node().
Actually, since commit c1e31d1 (ARM: imx: create
mxc_arch_reset_init_dt() for DT boot), imx6q/dl should try to use
mxc_restart() by calling mxc_arch_reset_init_dt() beforehand, where
things like of_iomap() can be done.
The patch updates mxc_restart() a little bit to get it work for imx6q/dl
and kill imx6q_restart() completely.
Reported-by: Nathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
As mx53 is a dt-only SoC, we should retrieve the iomuxc base address from the
device tree, instead of using the old MX53_IO_ADDRESS method.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
As mx53 is a dt-only SoC, we should retrieve the tzic base address from the
device tree, instead of using the old MX53_IO_ADDRESS method.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
As mx53 is a dt-only SoC, we should retrieve the gpt base address and irq
from the device tree, instead of using the old MX53_IO_ADDRESS method.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The IS_ERR() macro is defined in the linux/err.h header file, so include
it explicitly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The i.MX6 has two general-purpose LVDS clocks that can be driven
from a variety of sources. This patch adds a mux and a gate for
both of these clocks.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The patch enables soc bus infrastructure and adds a function
imx_soc_device_init() to report soc info via soc device interface for
imx6qdl and imx6sl. With the support, user space can get soc related
info by looking at sysfs like below.
$ cat /sys/devices/soc0/machine
Freescale i.MX6 Quad SABRE Smart Device Board
$ cat /sys/devices/soc0/family
Freescale i.MX
$ cat /sys/devices/soc0/soc_id
i.MX6Q
$ cat /sys/devices/soc0/revision
1.2
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add imx6sl support into imx_init_revision_from_anatop(), so that it can
be used to initialize cpu type and revision on imx6sl.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The patch creates a common function imx_init_revision_from_anatop() by
merging imx6q_init_revision() and imx_anatop_get_digprog(), so that any
SoC that encodes revision info in anatop can use it to initialize
revision.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It calls imx_set_soc_revision() to set up soc revision in
imx6q_init_revision(), and replaces all the occurrences of
imx6q_revision() with common helper imx_get_soc_revision().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Similar to what we do for cpu type, the patch adds helper functions
imx_set_soc_revision() and imx_get_soc_revision() to maintain
imx_soc_revision in cpu.c.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add low-level debug support for vybrid, so that earlyprintk can be
enabled for debugging early boot issue.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This flag is a NOOP since 2.6.35 and can be removed.
This is an update for 3.11 of a patch already sent for 3.10
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Config iomux-gpr1 to select clock source for fec system clock.
Clear gpr1[14], gpr1[18-17] bit to select the fec clock source
from internal anatop PLL.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
There's a pll4_audio_div clock, an extra divider for pll4, missing
in current clock tree, thus add it.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
EXYNOS is now Device Tree (DT) only platform so it makes no sense to have
config options responsible for enabling platform specific DT support.
Moreover the kernel image won't even link if neither CONFIG_MACH_EXYNOS4_DT
nor CONFIG_MACH_EXYNOS5_DT config option is enabled (linker fails with "no
machine record defined" error).
Remove CONFIG_MACH_EXYNOS[4,5]_DT config options and just use the standard
CONFIG_ARCH_EXYNOS[4,5] ones instead.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
s3c2410 and s3c2442 share the same dma channels while s3c2440 has
slight differences. But on all three the reachable sources per dma
channel has constraints attached and thus encodes the usable
combinations using the S3C24XX_DMA_CHANREQ macro.
This also fixes the warning about s3c2410_dma_resource being unused
as reported by Olof Johansson.
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Currently the s3c sound support selects CONFIG_S3C2410_DMA on s3c24xx
architectures while the generic dma config is enabled by CONFIG_S3C24XX_DMA.
With the way the Kconfig options are layed out currently it is possible
to enable Samsung sound support without enabling the necessary dma support
resulting in warnings like
warning: (SND_SOC_SAMSUNG && SND_S3C24XX_I2S && SND_S3C2412_SOC_I2S &&
SND_SOC_SAMSUNG_SMDK2443_WM9710 && SND_SOC_SAMSUNG_LN2440SBC_ALC650)
selects S3C2410_DMA which has unmet direct dependencies (ARCH_S3C24XX &&
S3C24XX_DMA && (CPU_S3C2410 || CPU_S3C2442))
Therefore bring the s3c2410 dma support in line with the way the other
s3c24xx SoCs handle this by having the SoC dma-support selected if the generic
s3c dma support is enabled and have the sound support depend on S3C24XX_DMA
on these arches. The s3c2442 is using the same dma descriptors and therefore
also selected S3C2410_DMA.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The generic PHY framewrok expects different properties than the
old USB PHY framework. Supply those properties.
Fixes USB OTG port on beagle after the Generic PHY framework was
merged in greg/usb-next. [1]
[1] - https://lkml.org/lkml/2013/9/27/581
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
AM335x EVM-SK have only support for audio playback (stereo jack on the
board) via tlv320aic3106 codec connected to McASP1.
Enable the support for audio playback on the board:
- McASP1 configuration
- tlv320aic3106 configuration
- Machine driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
This patch adds a second tuple to reg property. The new property tuple
describes the memory location for data port registers mapped trough
L3 bus on am33xx. The both property tuples are named accordingly in
the reg-names property.
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
-> Adding pinmux for cpsw, i2c0.
-> Enabling the modules that are present in AM4372 EPOS EVM
These modules are tested on AM4372 EPOS EVM.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Populate nodes for l2-cache-controller, EDMA, mailbox,
mmc, sham.
Update as well DT properties for epwmss, aes, des.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Added dr_mode property in dwc3 and set its default mode to device.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
smps10 should be enabled only in the case of host mode. So stop
doing always_on, boot_on from smps10_out1. The driver will enable
it in host mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Do not reset GPIO1 at boot-up because GPIO 7 in GPIO1 block is used on
OMAP4460 PandaBoard-ES to select voltage register in TPS62361 which
supplies VDD_MPU.
Without this, OMAP4460 PandaBoard-ES boards fail to boot-up because
MPU voltage switches over to VSET0 voltage value (boot voltage) which
is not sufficient to operate the device at OPP100.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Do not reset GPIO0 at boot-up because GPIO0 is used
on AM335x EVM-SK to control VTT regulators on DDR3.
Without this EVM-SK boards fail to boot-up because
of DDR3 corruption.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
On OMAP we have co-processor IPs, memory controllers,
GPIOs which control regulators and power switches to
PMIC, and SoC internal Bus IPs, some or most of which
should either not be reset or idled or both at init.
(In some cases there are erratas which prevent an IP
from being reset)
Have a way to pass this information from DT.
Update the am33xx/omap4 and omap5 dtsi files with the
new bindings for modules which either should not be
idled. reset or both. A later patch would cleanup the
same information that exists today as part of the hwmod
data files.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The generic PHY framewrok expects different properties than the
old USB PHY framework. Supply those properties.
Fixes USB OTG port on GAT04 and N900 after the Generic PHY framework was
merged in greg/usb-next. [1]
[1] - https://lkml.org/lkml/2013/9/27/581
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The arm arch timers frequency are now programmed in the CNTFREQ
per-cpu register by the timer code using the secure API [1].
So remove the redundant entry from the dts.
[1] http://marc.info/?l=linux-omap&m=138139106312786&w=2
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Generate ep93xx_defconfig by doing:
make ep93xx_defconfig
make savedefconfig
mv defconfig arch/arm/configs/ep93xx_defconfig
No function change. This just refreshes the ep93xx_defconfig to make it
easier and cleaner when adding new entries.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <rmallon@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order for ASID macro to be used as expression passed to
inline asm as 'r' operand it needs to give 32 bit unsigned result,
not unsigned 64bit expression.
Otherwise when 64bit ASID is passed to inline assembler statement
as 'r' operand (32bit) compiler behavior is not well specified.
For example when __flush_tlb_mm function compiled in big endian
case, and ASID is passed to tlb_op macro directly, 0 will be passed
as 'mcr 15, 0, r4, cr8, cr3, {2}' argument in r4, unless ASID
macro changed to produce 32 bit result.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
In big endian mode mcpm_entry_point is first function
that called on secondaries CPU. First it should switch
CPU into big endian code.
[ben.dooks@codethink.co.uk: merge fix patch from Victor into this]
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
In case of BE8 kernel data is in BE order whereas code stays in LE
order. Move sigreturn_codes to separate .S file and use proper
assembler mnemonics for these code snippets. In this case compiler
will take care of proper instructions byteswaps for BE8 case.
Change assumes that sufficiently Thumb-capable tools are used to
build kernel.
Problem was discovered during ltp testing of BE system: all rt_sig*
tests failed. Tested against the same tests in both BE and LE modes.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Fix inline asm for atomic64_xxx functions in arm atomic.h. Instead of
%H operand specifiers code should use %Q for least significant part
of the value, and %R for the most significant part of the value. %H
always returns the higher of the two register numbers, and therefore
it is not endian neutral. %H should be used with ldrexd and strexd
instructions.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
The arch_kgdb_breakpoint() function uses an inline assembly directive
to assemble a specific instruction using .word. This means the linker
will not treat is as an instruction, and therefore incorrectly swap
the endian-ness if running BE8.
As noted, this code means that kgdb is really only usable on arm32
kernels, and should be made dependant on not being a thumb2 kernel
until fixed. However this is not something to be added to this patch.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Currently BUG() uses .word or .hword to create the necessary illegal
instructions. However if we are building BE8 then these get swapped
by the linker into different illegal instructions in the text. This
means that the BUG() macro does not get trapped properly.
Change to using <asm/opcodes.h> to provide the necessary ARM instruction
building as we cannot rely on gcc/gas having the `.inst` instructions
which where added to try and resolve this issue (reported by Dave Martin
<Dave.Martin@arm.com>).
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Use <asm/opcodes.h> to correctly transform instruction byte ordering
into in-memory ordering.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
The <hardware/coresight.h> needs to take into account the endian-ness
of the processor when reading and writing data, so change to using
the readl/writel relaxed variants from the raw ones.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
To avoid having to make every text section swap the instruction order
of all instructions, make sure modules are built also built with --be8
(as is the current kernel final link).
If we do not do this, we would end up having to swap all instructions
when loading a module, instead of just the instructions that we are
applying ELF relocations to.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
When in BE8 mode, our instructions are not in the same ordering as the
data, so use <asm/opcodes.h> to take this into account.
Note, also requires modules to be built --be8
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
The trap handler needs to take into account the endian configuration of
the system when loading instructions. Use <asm/opcodes.h> to provide the
necessary conversion functions.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
If we are in BE8 mode, we must deal with the instruction stream being
in LE order when data is being loaded in BE order. Ensure the data is
swapped before processing to avoid thre following:
Change to using <asm/opcodes.h> to provide the necessary conversion
functions to change the byte ordering.
This stops the following warning messages from the kernel on a fault:
Unhandled fault: alignment exception (0x001) at 0xbfa09567
Alignment trap: not handling instruction 030091e8 at [<80333e8c>]
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add indication we can run these cores in BE mode, and ensure that the
secondary CPU is set to big-endian mode in the initialisation code as
the initial code runs little-endian.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Apart from a xgmac driver issue, the highbank seems to work correctly in
big-endian mode. Allow the selection of big-endian in the system.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Rob Herring <rob.herring@calxeda.com>
The smp_scu driver needs to use the relaxed readl/write accessors
to avoid any issues with the endian mode the processor core is in.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Ensure the twd driver uses the correct calls to access the hardware
to ensure that we do not end up with data in the wrong endian format.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
The PL01X debug code needs to take into account which endian mode the
processor is running in. If it is big-endian, ensure the data is swapped
appropriately.
Note, we could do this slightly more efficiently if we have an macro to
do the necessary swap for the bits used by test.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
If we are booting in LE and compiled for BE8, then add code to
set the state to bE8. Since the instruction stream is always LE,
we do not need to do anything special to the instruction.
Also ensure that the secondary processors are started in the same mode.
Note, we do add about 20 bytes to the kernel image, but it seems easier
to do this than adding another configuration to change.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The fixup_pv_table assumes that the instructions are in the same
endian configuration as the data, but when the CPU is running in
BE8 the instructions stay in little-endian format.
Make sure if CONFIG_CPU_ENDIAN_BE8 is set that we do all the
alterations to the instructions taking in to account the LDR/STR
will be swapping the data endian-ness.
Since the code is only modifying a byte, we avoid dual-swapping
the data, and just change the bits we clear and ORR in (in the
case where the code is not thumb2).
For thumb2, we add the necessary rev16 instructions to ensure that
the instructions are processed in the correct format, as it was
easier than re-writing the code to contain a mask and shift.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Add ARM_BE8() helper to wrap any code conditional on being
compile when CONFIG_ARM_ENDIAN_BE8 is selected and convert
existing places where this is to use it.
Acked-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
The Kconfig for arch/arm/mach-ixp4xx has a local definition
of ARCH_SUPPORTS_BIG_ENDIAN which could be used elsewhere.
This means that if IXP4xx is selected and this symbol is
selected eleswhere then an warning is produced.
Clean the following error up by making the symbol be
selected by the main ARCH_IXP4XX definition and have a
common definition in arch/arm/mm/Kconfig
warning: (ARCH_xxx) selects ARCH_SUPPORTS_BIG_ENDIAN which has unmet direct dependencies (ARCH_IXP4XX)
warning: (ARCH_xxx) selects ARCH_SUPPORTS_BIG_ENDIAN which has unmet direct dependencies (ARCH_IXP4XX)
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
OMAP3 PM core requires IVA2 bootmode to be set to idle during init. Currently,
a direct register write is used for this. Add a new ctrl API for this purpose
instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP3 PM code for off-mode currently saves the scratchpad contents for CM
registers within OMAP control module driver. However, as we are separating
CM code into its own driver, this must be moved also. This patch adds a
new API for saving the CM scratchpad contents and uses this from the high
level scratchpad save function.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
McBSP driver require special hacks to enable/disable the autoidle feature
for its interface clock for the proper function of the sidetone hardware.
Currently the driver just writes CM registers directly, which should be
avoided. Thus, changed the driver to use the new deny/allow_autoidle
clock API calls.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some drivers require direct access to the autoidle functionality of the
interface clocks. Added clock APIs for these, so that the drivers do not
need to access CM registers directly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Users of the CM funtionality should not access the CM registers directly
by themselves. Thus, added new CM driver APIs for the OMAP2 specific
functionalities which support the existing direct register accesses, and
changed the platform code to use these. This is done in preparation
for moving the CM code into its own individual driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Extend the list of power gates found on Tegra114. Note that there are
now holes in the list, so perhaps a simple array is no longer the best
data structure to represent it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
There's no need to modify these at runtime, it is static data and never
needs to change.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Instead of duplicating powergate defines, reuse the ones from the
include/linux/tegra-powergate.h header file.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The LP1 suspend procedure is the same with Tegra30 and Tegra114. Just
need to update the difference of the register address, then we can
continue to share the code.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch re-calculates the LP1 data of tegra30/114_sdram_pad_address
to base on its label not rely on others. This can make easier to
maintain if some other Tegra chips keep re-using these codes in the
future. And change the name of tegra30_sdram_pad_save to
tegra_sdram_pad_save to make it more common to other chips.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The CPUIdle function of Tegra124 is identical to Tegra114, so we share
the same driver with Tegra114.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Because the CPU0 was the first up and the last down core when cluster
power up/down or platform suspend. So only CPU0 needs the rest of the
functions to reset flow controller and re-enable SCU and L2. We also
move the L2 init function for Cortex-A15 to there. The secondery CPU
can just call cpu_resume.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The procedure of CPU hotplug for Tegra124 is same with Tegra114. We
re-use the same function with it.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The PMC HW is not identical to the existing Tegra SoC. Hence add to it.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add Tegra124 SoC support that base on CortexA15MP Core. And enable the
SMP function that can re-use the same procedure with Tegra114.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Various fuses on Tegra include information that's unique to an individual
chip, or a subset of chips. Call add_device_randomness() with this data
to perturb the initial state of the random pool.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
omap3 boards.
Note that that these are based on a merge of the
following for the dependencies:
- v3.12-rc5 for fixes to pinctrl mask
- omap-for-v3.13/dt-signed to avoid pointless merge conflicts
- omap-for-v3.13/quirk-signed for legacy pdata handling
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=9Iuv
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/board-removal-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
Changes needed to drop legacy booting support for some
omap3 boards.
Note that that these are based on a merge of the
following for the dependencies:
- v3.12-rc5 for fixes to pinctrl mask
- omap-for-v3.13/dt-signed to avoid pointless merge conflicts
- omap-for-v3.13/quirk-signed for legacy pdata handling
* tag 'omap-for-v3.13/board-removal-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (125 commits)
ARM: OMAP2+: remove legacy support for IGEP boards
ARM: OMAP2+: Remove legacy support for zoom platforms
ARM: OMAP2+: Remove legacy booting support for omap3 EVM
ARM: OMAP2: delete board-rm680
ARM: dts: add minimal DT support for Nokia N950 & N9 phones
ARM: dts: Add basic support for zoom3
ARM: dts: Add basic support for TMDSEVM3730 (Mistral AM/DM37x EVM)
ARM: dts: Add common support for omap3-evm
ARM: dts: Shared file for omap GPMC connected smsc911x
+Linux 3.12-rc5
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Commit f8e7ba66 (ARM: OMAP1: fix incorrect placement of
__initdata tag) fixed things but we started seeing section
warnings. Looks like I missed those in my automatic
build scripts:
Section mismatch in reference from the variable omap7xx_gpio6 to the (unknown reference) .init.data:(unknown)
Section mismatch in reference from the variable omap7xx_gpio6 to the (unknown reference) .init.data:(unknown)
Section mismatch in reference from the variable omap7xx_gpio5 to the (unknown reference) .init.data:(unknown)
...
Fix the issue by removing __initdata for the resources.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Device Tree support for IGEP boards in mainline is almost
finished. The only remaining bits are support for the
Marvell SD8686 wifi + BT and TFP410 DVI chips.
Adding support for these should be straightforward so let's
not block OMAP3 moving to Device Tree only boot and remove
the board file for IGEP boards.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We now have pretty decent device tree based support for
zoom platforms. It's not complete, but basics work for
me so adding more features should be quite trivial.
Looks like also 3630 sdp is zoom based, and looking
at it's board file should also be trivial to support
with the device tree based booting.
Patches are welcome if people are still using these.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We now have pretty decent support with the device tree
based booting. Patches to add more features are welcome.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Will Deacon