Currently the driver boots only via device tree hence add a
dependency on CONFIG_OF. This leaves with a bunch of unused code
so clean that up. This patch also makes use of probe_new function
in place of the probe function so as to avoid passing i2c_device_id.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Rework the IRQ handler by using HW IRQ number and status bit.
Each HW IRQ number is matched with TPS65217 register layout[*].
(USB IRQ number is 0, AC is 1, Push button is 2)
When an interrupt is enabled, mask bit should be cleared (unmasked).
If an interrupt is disabled, then mask bit should be set (masked).
This mask value is updated into the TPS65217 register in irq_sync_unlock().
Mask bit and interrupt status bit can be handled with HW IRQ number.
Eventually, additional IRQ data, 'tps65217_irqs[]' and the function,
'irq_to_tps65217_irq()' are not necessary.
[*] TPS65217 interrupt register layout
Bit7 6 5 4 3 2 1 0
----------------------------------------------
| x | PBM | ACM | USBM | x | PBI | ACI | USBI
PBM: Push button status change interrupt mask
ACM: AC interrupt mask
USBM: USB power status change interrupt mask
PBI: Push button status change interrupt
ACI: AC power status change interrupt
USBI: USB power status change interrupt
x: Not used
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
TPS65217 interrupt register includes read/writeable mask bits with
read-only status bits. (bit 4, 5, 6 are R/W, bit 0, 1, 2 are RO)
And reserved bit is not required.
Register update operation is preferred for disabling all interrupts during
the device initialisation.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Enum value of 'tps65217_irq_type' is not matched with DT parsed hwirq
number[*].
The MFD driver gets the IRQ data by referencing hwirq, but the value is
different. So, irq_to_tps65217_irq() returns mismatched IRQ data.
Eventually, the power button driver enables not PB but USB interrupt
when it is probed.
According to the TPS65217 register map[**], USB interrupt is the LSB.
This patch defines synchronized IRQ value.
[*] include/dt-bindings/mfd/tps65217.h
[**] http://www.ti.com/lit/ds/symlink/tps65217.pdf
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for handling IRQs: power button, AC and USB power state
changes. Mask and interrupt bits are shared within one register, which
prevents us to use regmap_irq implementation. New irq_domain is created in
order to add interrupt handling for each tps65217's subsystem. IRQ
resources have been added for charger subsystem to be able to notify about
AC and USB state changes.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The TPS65217 has a pre-defined power-up / power-down sequence which in
a typical application does not need to be changed. However, it is possible
to define custom sequences under I2C control. The power-up sequence is
defined by strobes and delay times. Each output rail is assigned to a
strobe to determine the order in which the rails are enabled.
Every regulator of tps65217 PMIC has sequence registers and every
regulator has a default strobe value and gets disabled when a particular
power down sequence occurs.
To keep a regulator on during suspend we write value 0 to strobe so
that the regulator is out of all sequencers and is not impacted by any
power down sequence. Hence saving the default strobe value during probe
so that when we want to regulator to be enabled during suspend we write 0
to strobe and when we want it to get disabled during suspend we write
the default saved strobe value.
This allows platform data to specify which power rails should be on or off
during RTC only suspend. This is necessary to keep DDR state while in RTC
only suspend.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
[Enhanced commit log and added dynamic allocation for strobes]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow regmap to provide debugfs access to the register map by telling it
what registers are valid.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Now this driver uses devm_regulator_register() so we don't need to save rdev
pointer to tps->rdev[i] for cleanup.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
If we compile the TPS65217 for a 64bit architecture we receive the following
warnings:
drivers/mfd/tps65217.c: In function ‘tps65217_probe’:
drivers/mfd/tps65217.c:173:13:
warning: cast from pointer to integer of different size
chip_id = (unsigned int)match->data;
^
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Below is the equation in original code:
tps65217_uv1_ranges:
0 ... 24: uV = vsel * 25000 + 900000;
25 ... 52: uV = (vsel - 24) * 50000 + 1500000;
= (vsel - 25) * 50000 + 1550000;
53 ... 55: uV = (vsel - 52) * 100000 + 2900000;
= (vsel - 53) * 100000 + 3000000;
56 ... 62: uV = 3300000;
tps65217_uv2_ranges:
0 ... 8: uV = vsel * 50000 + 1500000;
9 ... 13: uV = (vsel - 8) * 100000 + 1900000;
= (vsel - 9) * 100000 + 2000000;
14 ... 31: uV = (vsel - 13) * 50000 + 2400000;
= (vsel - 14) * 50000 + 2450000;
The voltage tables are composed of linear ranges.
This patch converts this driver to use multiple linear ranges APIs.
In original code, voltage range for DCDC1 is 900000 ~ 1800000 and voltage range
for DCDC3 is 900000 ~ 1500000. This patch separates the range 25~52 in
tps65217_uv1_ranges table to two linear ranges: 25~30 and 31~52.
This change makes it possible to reuse the same linear_ranges table for DCDCx.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The TPS65217 chip contains a boost converter and current sinks which can be
used to drive LEDs for use as backlights. Expose this functionality via the
backlight API.
Tested on an AM335x based custom board with a single WLED string, using
different values for ISEL and FDIM (though it would be hard to tell the
difference except for the value in WLEDCTRL1). Both instantiation through the
device tree and by passing platform data have been tested. Testing has been
done with an Androidized 3.2 kernel from the rowboat project. Koen Kooi
reported the driver to be working on a Beaglebone board with LCD3 cape
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Regulator platform data handling was mistakenly added to MFD
driver. So we will see build errors if we compile MFD drivers
without CONFIG_REGULATOR. This patch moves regulator platform
data handling from TPS65217 MFD driver to regulator driver.
This makes MFD driver independent of REGULATOR framework so
build error is fixed if CONFIG_REGULATOR is not set.
drivers/built-in.o: In function `tps65217_probe':
tps65217.c:(.devinit.text+0x13e37): undefined reference
to `of_regulator_match'
This patch also fix allocation size of tps65217 platform data.
Current implementation allocates a struct tps65217_board for each
regulator specified in the device tree. But the structure itself
provides array of regulators so one instance of it is sufficient.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
This commit adds device tree support for tps65217 pmic. And usage
details are added to device tree documentation. Driver is tested
by using kernel module with regulator set and get APIs.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert tps65217_pmic_ldo1_ops to use regulator_list_voltage_table.
We have n_voltages and volt_table settings in regulator_desc,
so we don't need the table and table_len fields in struct tps_info.
Thus remove them from struct tps_info.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch converts .is_enabled and .get_voltage_sel to
regulator_is_enabled_regmap and regulator_get_voltage_sel_regmap.
For .enable, .disable, and .set_voltage_sel, the write protect level is either
1 or 2. So we cannot use regulator_[enable|disable|set_voltage_sel]_regmap.
Now we store the enable reg/mask and vsel reg/mask in regulator_desc,
so we can remove enable_mask, set_vout_reg, and set_vout_mask from
struct tps_info.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The TPS65217 chip is a power management IC for Portable Navigation Systems
and Tablet Computing devices. It contains the following components:
- Regulators
- White LED
- USB battery charger
This patch adds support for tps65217 mfd device. At this time only
the regulator functionality is made available.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Keerthy