* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] qla1280: retain firmware for error recovery
[SCSI] attirbute_container: Initialize sysfs attributes with sysfs_attr_init
[SCSI] advansys: fix regression with request_firmware change
[SCSI] qla2xxx: Updated version number to 8.03.02-k2.
[SCSI] qla2xxx: Prevent sending mbx commands from sysfs during isp reset.
[SCSI] qla2xxx: Disable MSI on qla24xx chips other than QLA2432.
[SCSI] qla2xxx: Check to make sure multique and CPU affinity support is not enabled at the same time.
[SCSI] qla2xxx: Correct vp_idx checking during PORT_UPDATE processing.
[SCSI] qla2xxx: Honour "Extended BB credits" bit for CNAs.
[SCSI] scsi_transport_fc: Make sure commands are completed when rport is offline
[SCSI] libiscsi: Fix recovery slowdown regression
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
On specific platforms, MSI is unreliable on some of the QLA24xx chips, resulting
in fatal I/O errors under load, as reported in <http://bugs.debian.org/572322>
and by some RHEL customers.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Checks should only be done for NPIV-capable ISPs. Original code
could result in PORT_UPDATEs being missed on non-NPIV-capable
ISPs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Original code incorrectly assumed only status-type-0
IOCBs would be queued to the response-queue, and thus all
entries would safely reference a VHA from the IOCB
'handle.'
Cc: stable@kernel.org
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
qla2xxx: EEH added call to pci_restore_state.
qla2xxx: EEH added delay in slot reset routine.
qla2xxx: EEH moved call to pci_save_state(), see (1).
qla2xxx: EEH additional changes for RHEL5.5.
qla2xxx: EEH added function call, removed function call, see (2).
(1) In qla2xxx_probe_one the call to pci_save_state() has been
moved to after the call to qla2xxx_request_irqs().
(2) Add call to pci_disable_pcie_error_reporting() in remove_one.
Delete call to pci_cleanup_aer_uncorrect_error_status() in pci_resume.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix to accommodate a hardware bug in multiqueue mode that does not
work properly when acknowledgement of MSIX Interrupts is disabled.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Removed the module parameters ql2xqfulltracking and ql2xqfullrampup
since the queue depth ramp up/down functionality is moved to scsi-ml.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Correct issues where the lower scsi-status would be improperly
cleared, instead, allow the midlayer to process the status after
the proper residual-count checks are performed. Finally,
validate firmware status flags prior to assigning values from the
FCP_RSP frame.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Michael Hernandez <michael.hernandez@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The mailbox register values may assist in debugging efforts.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In fabric-login based on iop BIT_8 firmware notifies presence of
a FCP2 device and not necessarily a TAPE device. So instead of
setting FCF_TAPE_PRESENT flag there we set it using
scsi_device->type after mid-layer scan recognises "type" of the
device.
It also adds a new flag FCF_FCP2_DEVICE for any future use.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
ISPs which support this feature include 23xx and above.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The interrupt handler clears the interrupt status register for response
updates in the base queue while working in the multique mode. This could lead
to missing interrupt for async events, mail box completions etc. as these are
also handled in the base queue. The fix ensures that the interrupt bit is not
cleared for response updates in the ISR when the driver is working in
multiqueue mode.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The RSCN processing is skipped if the event received is global and vha is not recipient.
Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Treat a global port-unavailable PORT_UPDATE (8014h) AEN as a
loop-down event. For this case, within the FCoE domain, the
'logical' interface has been terminated, but the driver will
not receive the classic LOOP_DOWN AEN.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Reverted back a change in qla*_intr_handler code that caused an increase in
cpu cycles by allowing interrupts to occur while the instance hardware lock
was being held. Fix by taking the lock in irqsave mode.
Reported-and-tested-by: Douglas W. Styner <douglas.w.styner@intel.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The SCSI-midlayer's fast-fail codes consider an DID_ERROR status
as a driver-error and the failed I/O would then be retried in the
midlayer without being fast-failed to dm-multipath. DID_BUS_BUSY
status returns would induce unneeded path-failures events being
propagated to the DM/MD.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Changing a lun's queue depth (/sys/block/sdX/device/queue_depth)
isn't sticky when the device is connected via a QLogic fibre
channel adapter.
The QLogic qla2xxx fibre channel driver dynamically adjusts a
lun's queue depth. If a user has a specific need to limit the
number of commands issued to a lun (say a tape drive, or a shared
raid where the total commands issued to all luns is limited at
the controller level, for example) and writes a limiting value to
/sys/block/sdXX/device/queue_depth, the qla2xxx driver will
silently and gradually increase the queue depth back to the
driver limit of ql2xmaxqdepth. While reducing this value (module
parameter) or increasing the interval between ramp ups
(ql2xqfullrampup) offers the potential for a work around it would
be better to have the option of just disabling the dynamic
adjustment of queue depth.
This patch implements an "off switch" as a module parameter.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the module parameter ql2xmultique_tag to 1 to enable this
feature. In this mode, the total number of response queues
created is equal to the number of online cpus. Turning the block
layer's rq_affinity mode on enables requests to be routed to the
proper cpu and at the same time it enables completion of the IO
in a response queue that is affined to the cpu in the request
path.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the number of request queues to the module paramater
ql2xmaxqueues. Each vport gets a request queue. The QoS value
set to the request queues determines priority control for queued
IOs. If QoS value is not specified, the vports use the default
queue 0.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
When IRQs are shared by multiple controllers and if the first one
to register does not disable the IRQ, then IRQ will be enabled
for all other controllers by default, irrespective of their
setting. With IRQF_DISABLED registration, the driver interrupt
routine was called with interrupt enabled always. Disbaling the
registration with IRQF_DISABLED, since driver code is re-entrant
safe and all critical sections are guarded with interrupt safe
locks.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
General cleanup of extraneous/legacy crud.
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code used an overabundance of indirect pointers to
function helpers. Instead, the driver can exploit the immutable
properties of a queue's ISP-association and ID, which are both
known at queue initialization-time.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
To ensure smooth operations amongst the FCoE and NIC side
components of the ISP81xx chip, the FCoE driver (qla2xxx) must
ensure the 10gb NIC driver (qlge) does not timeout waiting for
IDC (Inter-Driver Communication) acknowledgments. The
acknowledgment requirements are trivial -- a simple mirroring of
incoming mailbox registers during the AEN to a process-context
capable mailbox command.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Correct response-queue-0 processing by instructing the firmware
to run with interrupt-handshaking disabled, similarly to what is
now done for all non-0 response queues. Since all
response-queues now run in the same mode, the driver no longer
needs the hot-path 'is-disabled-HCCR' test.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Codes to support new FCoE boards.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code would inadvertanly place I/Os on the default
request-queue. Also, correctly pass in the proper MSI-X vector
during response-queue initialization.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Software should not touch this region of flash, as the firmware
will be the only writer and consumer of the region.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following changes have been made:
1. Scan outstanding commands only in the queue where it is submitted
2. Update queue registers directly in the fast path
3. Queue specific BAR is remapped only for multiq capable adapters
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following changes have been made.
1. qla_hw_data structure holds an array for request queue pointers,
and an array for response queue pointers.
2. The base request and response queues are created by default.
3. Additional request and response queues are created at the time of vport
creation. If queue resources are exhausted during vport creation, newly
created vports use the default queue.
4. Requests are sent to the request queue that the vport was assigned
in the beginning.
5. Responses are completed on the response queue with which the request queue
is associated with.
[fixup memcpy argument reversal spotted by davej@redhat.com]
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following changes have been made:
1. Outstanding commands are based on a request queue, scsi_qla_host
does not maintain it anymore.
2. start_scsi is accessed via isp_ops struct instead of direct
invocation.
3. Interrupt registrations are done using response queue instead of
device id.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This has qla2xxx use the new transport error values instead of
DID_BUS_BUSY. I am not sure if all the errors
in qla_isr.c I changed are transport related. We end up blocking/deleting
the rport for all of them so it is better to use the new transport error since
the fc classs will decide when to fail the IO.
With this patch if I pull a cable then IO that had reached
the driver, will be failed with DID_TRANSPORT_DISRUPTED (not including
tape). The fc class will then fail the IO when the fast io fail tmo
has fired, and the driver will flush any other commands running.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As the driver is only interested in bits 0-9 of the 1st
RSCN-payload word:
rsvd[15:14]RscnEventQualifier[13:10]Fmt[9:8]Domain[7:0]
Area[15:8]Alpa[7:0]
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Add additional tightening of residual-count handling (originally
from commit 6acf819002) where the
driver should discard any lower SCSI-status during
firmware/transport residual-count mismatches.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix "occured" spelling errors. Most of these are in comments, which
I wouldn't normally bother with, but a couple are in printks, which
irritate me more. So I just fixed them all at the same time.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Josip Rodin noted
(http://article.gmane.org/gmane.linux.ports.sparc/10152) the
driver oopsing during registration of an rport to the
FC-transport layer with a backtrace indicating a dereferencing of
an shost->shost_data equal to NULL. David Miller identified a
small window in driver logic where this could happen:
> Look at how the driver registers the IRQ handler before the host has
> been registered with the SCSI layer.
>
> That leads to a window of time where the shost hasn't been setup
> fully, yet ISRs can come in and trigger DPC thread events, such as
> loop resyncs, which expect the transport area to be setup.
>
> But it won't be setup, because scsi_add_host() hasn't finished yet.
>
> Note that in Josip's crash log, we don't even see the
>
> qla_printk(KERN_INFO, ha, "\n"
> " QLogic Fibre Channel HBA Driver: %s\n"
> " QLogic %s - %s\n"
> " ISP%04X: %s @ %s hdma%c, host#=%ld, fw=%s\n",
> ...
>
> message yet.
>
> Which means that the crash occurs between qla2x00_request_irqs()
> and printing that message.
Close this window by enabling RISC interrupts after the host has
been registered with the SCSI midlayer.
Reported-by: Josip Rodin <joy@entuzijast.net>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The executing-HA of an SRB can be referenced from the sp->fcport.
Use this correct value while processing status-continuation data
and abort processing.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* Use correct 'ha' to mark a device lost from ISR.
I/Os will always be returned on the physical-HA.
qla2x00_mark_device_lost() should be called with the HA bound
to the fcport.
* Mark *all* devices lost during ISP-ABORT (bighammer).
These fixes correct issues discovered locally where during
link-perturbation and heavy vport-I/O fcport/rport states would
stray and an rport's scsi-target lost (timed-out).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
By allowing the qla2x00_alert_all_vps() to manage per-vport
recognition of the MBA.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This reverts commit bd2a1846b2.
The original (prior to the reverted commit) code was correct.
Additionally, the vp_idx should be checked during MBA_PORT_UPDATE
in order for proper handling to take place for a given vport.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Linus Torvalds