When we restore regulatory settings the world regulatory domain
is properly reset on cfg80211 (or user prefered regulatory domain)
but we were never setting back channel values for drivers that use
WIPHY_FLAG_CUSTOM_REGULATORY. Set these values up again by using
the orig_ channel parameters.
This fixes restoring custom regulatory settings upon disconnect
events.
Cc: compat@orbit-lab.org
Cc: Paul Stewart <pstew@google.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Senthilkumar Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By definition WIPHY_FLAG_STRICT_REGULATORY was intended to allow the
wiphy to adjust itself to the country IE power information if the
card had no regulatory data but we had no way to tell cfg80211 that if
the card also had its own custom regulatory domain (these are typically
custom world regulatory domains) that we want to follow the country IE's
noted values for power for each channel. We add support for this and
document it.
This is not a critical fix but a performance optimization for cards
with custom regulatory domains that associate to an AP with sends
out country IEs with a higher EIRP than the one on the custom
regulatory domain. In practice the only driver affected right now
are the Atheros drivers as they are the only drivers using both
WIPHY_FLAG_STRICT_REGULATORY and WIPHY_FLAG_CUSTOM_REGULATORY --
used on cards that have an Atheros world regulatory domain. Cards
that have been programmed to follow a country specifically will not
follow the country IE power. So although not a stable fix distributions
should consider cherry picking this.
Cc: compat@orbit-lab.org
Cc: Paul Stewart <pstew@google.com>
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Cc: Senthilkumar Balasubramanian <senthilb@qca.qualcomm.com>
Reported-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Regulatory updates set by CORE are ignored for custom regulatory cards.
Let us notify the changes to the driver, as some drivers uses core hint
to restore its orig_* reg domain setting.
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes' patch for "cfg80211: fix regulatory NULL dereference"
broke user regulaotry hints and it did not address the fact that
last_request was left populated even if the previous regulatory
hint was stale due to the wiphy disappearing.
Fix user reguluatory hints by only bailing out if for those
regulatory hints where a request_wiphy is expected. The stale last_request
considerations are addressed through the previous fixes on last_request
where we reset the last_request to a static world regdom request upon
reset_regdomains(). In this case though we further enhance the effect
by simply restoring reguluatory settings completely.
Cc: stable@vger.kernel.org
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a theoretical race that if hit will trigger
a crash. The race is between when we issue the first
regulatory hint, regulatory_hint_core(), gets processed
by the workqueue and between when the first device
gets registered to the wireless core. This is not easy
to reproduce but it was easy to do so through the
regulatory simulator I have been working on. This
is a port of the fix I implemented there [1].
[1] a246ccf81f
Cc: stable@vger.kernel.org
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This grants drivers access to the DFS region that a
regulatory domain belongs to.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wireless-regdb now has support for mapping a country to
one DFS region. CRDA sends this to us now so process it
so we can provide that hint to drivers. This will later be
used by code for processing DFS in a way that meets the
criteria for the DFS region the country belongs to.
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By the time userspace returns with a response to
the regulatory domain request, the wiphy causing
the request might have gone away. If this is so,
reject the update but mark the request as having
been processed anyway.
Cc: Luis R. Rodriguez <lrodriguez@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 4d9d88d1 by Scott James Remnant <keybuk@google.com> added
the .uevent() callback for the regulatory device used during
the platform device registration. The change was done to account
for queuing up udev change requests through udevadm triggers.
The change also meant that upon regulatory core exit we will now
send a uevent() but the uevent() callback, reg_device_uevent(),
also accessed last_request. Right before commiting device suicide
we free'd last_request but never set it to NULL so
platform_device_unregister() would lead to bogus kernel paging
request. Fix this and also simply supress uevents right before
we commit suicide as they are pointless.
This fix is required for kernels >= v2.6.39
$ git describe --contains 4d9d88d1
v2.6.39-rc1~468^2~25^2^2~21
The impact of not having this present is that a bogus paging
access may occur (only read) upon cfg80211 unload time. You
may also get this BUG complaint below. Although Johannes
could not reproduce the issue this fix is theoretically correct.
mac80211_hwsim: unregister radios
mac80211_hwsim: closing netlink
BUG: unable to handle kernel paging request at ffff88001a06b5ab
IP: [<ffffffffa030df9a>] reg_device_uevent+0x1a/0x50 [cfg80211]
PGD 1836063 PUD 183a063 PMD 1ffcb067 PTE 1a06b160
Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
CPU 0
Modules linked in: cfg80211(-) [last unloaded: mac80211]
Pid: 2279, comm: rmmod Tainted: G W 3.1.0-wl+ #663 Bochs Bochs
RIP: 0010:[<ffffffffa030df9a>] [<ffffffffa030df9a>] reg_device_uevent+0x1a/0x50 [cfg80211]
RSP: 0000:ffff88001c5f9d58 EFLAGS: 00010286
RAX: 0000000000000000 RBX: ffff88001d2eda88 RCX: ffff88001c7468fc
RDX: ffff88001a06b5a0 RSI: ffff88001c7467b0 RDI: ffff88001c7467b0
RBP: ffff88001c5f9d58 R08: 000000000000ffff R09: 000000000000ffff
R10: 0000000000000000 R11: 0000000000000001 R12: ffff88001c7467b0
R13: ffff88001d2eda78 R14: ffffffff8164a840 R15: 0000000000000001
FS: 00007f8a91d8a6e0(0000) GS:ffff88001fc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffff88001a06b5ab CR3: 000000001c62e000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process rmmod (pid: 2279, threadinfo ffff88001c5f8000, task ffff88000023c780)
Stack:
ffff88001c5f9d98 ffffffff812ff7e5 ffffffff8176ab3d ffff88001c7468c2
000000000000ffff ffff88001d2eda88 ffff88001c7467b0 ffff880000114820
ffff88001c5f9e38 ffffffff81241dc7 ffff88001c5f9db8 ffffffff81040189
Call Trace:
[<ffffffff812ff7e5>] dev_uevent+0xc5/0x170
[<ffffffff81241dc7>] kobject_uevent_env+0x1f7/0x490
[<ffffffff81040189>] ? sub_preempt_count+0x29/0x60
[<ffffffff814cab1a>] ? _raw_spin_unlock_irqrestore+0x4a/0x90
[<ffffffff81305307>] ? devres_release_all+0x27/0x60
[<ffffffff8124206b>] kobject_uevent+0xb/0x10
[<ffffffff812fee27>] device_del+0x157/0x1b0
[<ffffffff8130377d>] platform_device_del+0x1d/0x90
[<ffffffff81303b76>] platform_device_unregister+0x16/0x30
[<ffffffffa030fffd>] regulatory_exit+0x5d/0x180 [cfg80211]
[<ffffffffa032bec3>] cfg80211_exit+0x2b/0x45 [cfg80211]
[<ffffffff8109a84c>] sys_delete_module+0x16c/0x220
[<ffffffff8108a23e>] ? trace_hardirqs_on_caller+0x7e/0x120
[<ffffffff814cba02>] system_call_fastpath+0x16/0x1b
Code: <all your base are belong to me>
RIP [<ffffffffa030df9a>] reg_device_uevent+0x1a/0x50 [cfg80211]
RSP <ffff88001c5f9d58>
CR2: ffff88001a06b5ab
---[ end trace 147c5099a411e8c0 ]---
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Scott James Remnant <keybuk@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These files are non modular, but need to export symbols using
the macros now living in export.h -- call out the include so
that things won't break when we remove the implicit presence
of module.h from everywhere.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files were getting access to these two via the implicit
presence of module.h everywhere. They aren't modules, so they
don't need the full module.h inclusion though.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
During the association, the regulatory is updated by country IE
that reaps the previously found beacons. The impact is that
after a STA disconnects *or* when for any reason a regulatory
domain change happens the beacon hint flag is not cleared
therefore preventing future beacon hints to be learned.
This is important as a regulatory domain change or a restore
of regulatory settings would set back the passive scan and no-ibss
flags on the channel. This is the right place to do this given that
it covers any regulatory domain change.
Cc: stable@kernel.org
Reviewed-by: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reorder functions to remove the need for a forward declaration
introduced by the last commit.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Daniel Mack <daniel@zonque.org>
Cc: linux-wireless@vger.kernel.org
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function wiphy_update_regulatory() uses the static variable
last_request and thus needs to be called with reg_mutex held.
This is the case for all users in reg.c, but the function was
exported for use by wiphy_register(), from where it is called
without the lock being held.
Fix this by making wiphy_update_regulatory() private and introducing
regulatory_update() as a wrapper that acquires and holds the lock.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Daniel Mack <daniel@zonque.org>
Cc: linux-wireless@vger.kernel.org
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Two spaces and the second "KHz" suggest that the code author meant to
print the bandwidth but forgot it. The code appears in commit e702d3cf
already with two spaces and "KHz" in place of the bandwidth.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Several uses were missing terminating newlines.
Typo fix and macro neatening.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just a typo fix changing regulaotry to regulatory.
Signed-off-by: Mihai Moldovan <ionic@ionic.de>
CC: John W. Linville <linville@tuxdriver.com>
CC: Mohammed Shafi <shafi.wireless@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At the beginning of wiphy_update_regulatory() a check is performed
whether the request is to be ignored. Then the request is sent to
the driver nevertheless. This happens even if last_request points
to NULL, leading to a crash in the driver:
[<bf01d864>] (lbs_set_11d_domain_info+0x28/0x1e4 [libertas]) from [<c03b714c>] (wiphy_update_regulatory+0x4d0/0x4f4)
[<c03b714c>] (wiphy_update_regulatory+0x4d0/0x4f4) from [<c03b4008>] (wiphy_register+0x354/0x420)
[<c03b4008>] (wiphy_register+0x354/0x420) from [<bf01b17c>] (lbs_cfg_register+0x80/0x164 [libertas])
[<bf01b17c>] (lbs_cfg_register+0x80/0x164 [libertas]) from [<bf020e64>] (lbs_start_card+0x20/0x88 [libertas])
[<bf020e64>] (lbs_start_card+0x20/0x88 [libertas]) from [<bf02cbd8>] (if_sdio_probe+0x898/0x9c0 [libertas_sdio])
Fix this by returning early. Also remove the out: label as it is
not any longer needed.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Cc: linux-wireless@vger.kernel.org
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Daniel Mack <daniel@zonque.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These warnings are exposed by gcc 4.6.
net/wireless/reg.c: In function 'freq_reg_info_regd':
net/wireless/reg.c:675:38: warning: variable 'pr' set but not used
[-Wunused-but-set-variable]
net/wireless/lib80211_crypt_wep.c: In function 'lib80211_wep_build_iv':
net/wireless/lib80211_crypt_wep.c:99:12: warning: variable 'len' set but
not used [-Wunused-but-set-variable]
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch "cfg80211: add a timer for invalid user reg hints"
introduced a regression for the case where a secondary identical
regulatory hint from a user is sent. What would happen is the
second hint would schedule delayed work in to catch a timeout
but since we are never processing it given that the hint was already
applied we'd always hit the timeout and and restore regulatory
settings back to world regulatory domain. This is fixed by simply
avoiding sheduling work if the hint was already applied.
Tested-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have no other option but to inform userspace that we
have queued up their regulatory hint request when we are
given one given that nl80211 operates atomically on user
requests. The best we can do is accept the request, and
add a delayed work item for processing failure and cancel it
if we succeeed. Upon failure we restore the regulatory
settings and ignore the user input.
This fixes this reported bug:
https://bugzilla.kernel.org/show_bug.cgi?id=28112
Reported-by: gregoryx.alagnou@intel.com
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we restore regulatory settings its possible CRDA
will not reply because of a bogus user entry. In this
case the bogus entry will prevent any further processing
on cfg80211 for regulatory domains even if we restore
regulatory settings.
To prevent this we suck out all pending requests when
restoring regulatory settings and add them back into the
queue after we have queued up the reset work.
The impact of not having this applied is that a user
with privileges can issue a userspace regulatory hint
while we are disasocciating and this would prevent any
further processing of regulatory domains.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Regulatory devices issue change uevents to inform userspace of a need
to call the crda tool; however these can often be sent before udevd is
running, and were not previously included in the results of
udevadm trigger (which requests a new change event using the /uevent
attribute of the sysfs object).
Add a uevent function to the device type which includes the COUNTRY
information from the last request if it has yet to be processed, the
case of multiple requests is already handled in the code by checking
whether an unprocessed one is queued in the same manner and refusing
to queue a new one.
The existing udev rule continues to work as before.
Signed-off-by: Scott James Remnant <keybuk@google.com>
Acked-By: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Extend channel to frequency mapping for 802.11j Japan 4.9GHz band, according to
IEEE802.11 section 17.3.8.3.2 and Annex J. Because there are now overlapping
channel numbers in the 2GHz and 5GHz band we can't map from channel to
frequency without knowing the band. This is no problem as in most contexts we
know the band. In places where we don't know the band (and WEXT compatibility)
we assume the 2GHz band for channels below 14.
This patch does not implement all channel to frequency mappings defined in
802.11, it's just an extension for 802.11j 20MHz channels. 5MHz and 10MHz
channels as well as 802.11y channels have been omitted.
The following drivers have been updated to reflect the API changes:
iwl-3945, iwl-agn, iwmc3200wifi, libertas, mwl8k, rt2x00, wl1251, wl12xx.
The drivers have been compile-tested only.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Brian Prodoehl <bprodoehl@gmail.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes the misplaced article in the following:
"cfg80211: Updating information on frequency 5785 MHz for
20 a MHz width channel with regulatory rule:"
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No change in output for pr_<level> prefixes.
netdev_<level> output is different, arguably improved.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When two cards are connected with the same regulatory domain
if CRDA had a delayed response then cfg80211's own set regulatory
domain would still be the world regulatory domain. There was a bug
on cfg80211's logic such that it assumed that once you pegged a
request as the last request it was already the currently set
regulatory domain. This would mean we would race setting a stale
regulatory domain to secondary cards which had the same regulatory
domain since the alpha2 would match.
We fix this by processing each regulatory request atomically,
and only move on to the next one once we get it fully processed.
In the case CRDA is not present we will simply world roam.
This issue is only present when you have a slow system and the
CRDA processing is delayed. Because of this it is not a known
regression.
Without this fix when a delay is present with CRDA the second card
would end up with an intersected regulatory domain and not allow it
to use the channels it really is designed for. When two cards with
two different regulatory domains were inserted you'd end up
rejecting the second card's regulatory domain request.
This fails with mac80211_hswim's regtest=2 (two requests, same alpha2)
and regtest=3 (two requests, different alpha2) module parameter
options.
This was reproduced and tested against mac80211_hwsim using this
CRDA delayer:
#!/bin/bash
echo $COUNTRY >> /tmp/log
sleep 2
/sbin/crda.orig
And these regulatory tests:
modprobe mac80211_hwsim regtest=2
modprobe mac80211_hwsim regtest=3
Reported-by: Mark Mentovai <mark@moxienet.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be required in the next patch and it makes the
next patch easier to review.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These will be used earlier in the next few patches.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will simplify the synchronization for pending requests.
Without this we have a race between the core and when we
restore regulatory settings, although this is unlikely
its best to just avoid that race altogether.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Mark Mentovai <mark@moxienet.com>
Tested-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Everyone's doing it, its the cool thing.
Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the worst case you are seeing really odd things you want
more information than what is provided right now, for those
that insist and want debug info through CONFIG_CFG80211_REG_DEBUG
provide a print of when we are processing a channel and with what
regulatory rule.
Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can help with debugging issues. You will only see
these with CONFIG_CFG80211_REG_DEBUG enabled.
Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After a module loads you will have loaded the world roaming regulatory
domain or a custom regulatory domain. Further regulatory hints are
welcomed and should be respected unless the regulatory hint is coming
from a country IE as the IEEE spec allows for a country IE to be a subset
of what is allowed by the local regulatory agencies.
So disable all channels that do not fit a regulatory domain sent
from a unless the hint is from a country IE and the country IE had
no information about the band we are currently processing.
This fixes a few regulatory issues, for example for drivers that depend
on CRDA and had no 5 GHz freqencies allowed were not properly disabling
5 GHz at all, furthermore it also allows users to restrict devices
further as was intended.
If you recieve a country IE upon association we will also disable the
channels that are not allowed if the country IE had at least one
channel on the respective band we are procesing.
This was the original intention behind this design but it was
completely overlooked...
Cc: David Quan <david.quan@atheros.com>
Cc: Jouni Malinen <jouni.malinen@atheros.com>
cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should be enabling country IE hints for WIPHY_FLAG_STRICT_REGULATORY
even if we haven't yet recieved regulatory domain hint for the driver
if it needed one. Without this Country IEs are not passed on to drivers
that have set WIPHY_FLAG_STRICT_REGULATORY, today this is just all
Atheros chipset drivers: ath5k, ath9k, ar9170, carl9170.
This was part of the original design, however it was completely
overlooked...
Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is required later.
Cc: Easwar Krishnan <easwar.krishnan@atheros.com>
Cc: stable@kernel.org
signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch 4f366c5:
wireless: only use alpha2 regulatory information from country IE
removed some complex intersection we were always doing between the AP's
country IE info and what we got from CRDA. When CRDA sent us back a
regulatory domain we would do some sanity checks on that regulatory
domain response we just got. Part of these sanity checks included
checking that we already had performed an intersection for the
request of NL80211_REGDOM_SET_BY_COUNTRY_IE type.
This mean that cfg80211 was only processing country IEs for cases
where we already had an intersection, but since we removed enforcing
this this is no longer required, we should just apply the country
IE country hint with the data received from CRDA.
This patch has fixes intended for kernels >= 2.6.36.
Cc: stable@kernel.org
Reported-by: Easwar Krishnan <easwar.krishnan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using a WARN_ON(!mutex_is_locked())
use lockdep_assert_held() which compiles away
completely when lockdep isn't enabled, and
also is a more accurate assertion since it
checks that the current thread is holding the
mutex.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This provides a little more flexibility for human users, and it allows
us to use isalpha rather than the custom is_alpha_upper.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some cases there could be possible dereferencing freed pointer. The
update is intended to avoid this issue.
Signed-off-by: Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The "rd" variable isn't needed any more since 4f366c5dab
"wireless: only use alpha2 regulatory information from country IE"
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"Might as well remove reg_same_country_ie_hint() completely since we
already dealt with suspend/resume through the regulatory hint
disconnect." -- Luis
Reported-by: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The meaning and/or usage of the country IE is somewhat poorly defined.
In practice, this means that regulatory rulesets in a country IE are
often incomplete and might be untrustworthy. This removes the code
associated with interpreting those rulesets while preserving respect
for country "alpha2" codes also contained in the country IE.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
regulatory_init is only called by cfg80211_init which is in .init.text,
too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
smc91c92_cs: fix the problem of "Unable to find hardware address"
r8169: clean up my printk uglyness
net: Hook up cxgb4 to Kconfig and Makefile
cxgb4: Add main driver file and driver Makefile
cxgb4: Add remaining driver headers and L2T management
cxgb4: Add packet queues and packet DMA code
cxgb4: Add HW and FW support code
cxgb4: Add register, message, and FW definitions
netlabel: Fix several rcu_dereference() calls used without RCU read locks
bonding: fix potential deadlock in bond_uninit()
net: check the length of the socket address passed to connect(2)
stmmac: add documentation for the driver.
stmmac: fix kconfig for crc32 build error
be2net: fix bug in vlan rx path for big endian architecture
be2net: fix flashing on big endian architectures
be2net: fix a bug in flashing the redboot section
bonding: bond_xmit_roundrobin() fix
drivers/net: Add missing unlock
net: gianfar - align BD ring size console messages
net: gianfar - initialize per-queue statistics
...
Stanse discovered that kmalloc is being called with GFP_KERNEL while
holding this spinlock. The spinlock can be a mutex instead, which also
enables the removal of the unlock/lock around the lock/unlock of
cfg80211_mutex and the call to set_regdom.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This adds a new regulatory hint to be used when we know all
devices have been disconnected and idle. This can happen
when we suspend, for instance. When we disconnect we can
no longer assume the same regulatory rules learned from
a country IE or beacon hints are applicable so restore
regulatory settings to an initial state.
Since driver hints are cached on the wiphy that called
the hint, those hints are not reproduced onto cfg80211
as the wiphy will respect its own wiphy->regd regardless.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When cfg80211 starts it will send a core regulatory hint. This is
sent to the global workqueue but we force processing of it by
flushing the global workqueue. The flushing was done since
cfg80211 needs last_request to always be populated.
Avoid flushing the global workqueue by processing the work
required immediately instead of putting it into a linked
list and processing it after the flush.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In practice APs do not send country IE channel triplets for channels
the AP is not operating on and if they were to do so they would have
to use the regulatory extension which we currently do not process.
No AP has been seen in practice that does this though so just drop
those country IEs.
Additionally it has been noted the first series of country IE
channels triplets are specific to the band the AP sends. Propagate
the band on which the country IE was found on reject the country
IE then if the triplets are ever oustide of the band.
Although we now won't process country IE information with multiple
band information we leave the intersection work as is as it is
technically possible for someone to want to eventually process these
type of country IEs with regulatory extensions.
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previous to this and the last patch, titled,
"cfg80211: Fix 2 GHz subband calculation for country IEs"
we would end up treating these IEs as single channel units. These are in
fact just bogus IE triplets so ignore the entire IE if these are found.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Country IEs triplets are getting an extra channel with
the current count. This does not affect regulatory because
we always took the intersection between what the AP gave
and what CRDA believed is correct.
This however does fix processing some Country IEs with multiple
sequential 2 GHz triplets. Since our parser and the spec mandates
all channels be monitonically increasing we would drop the IE after
noticing the second triplet begins on a channel already processed.
APs that send these type of country IEs seems rare though.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enhances the way we parse country IEs to minimize
the number of regulatory rules that we create. It also fixes
our current implementation which treated country IE triplets
with only one channel as one independed regulatory rule even
though adjecent rules were also being provided.
Without this patch APs which send country IE information with
a channel triplet for each individual channel will force cfg80211
to deny HT40 operation as a regulatory rule would have been created
independently for each channel and as such configured only for
20 MHz operation.
Although 802.11n APs which send country IEs triplets in this fassion
are likely rare Benoit reports this against the Ubiquity NanoStation M5,
with Country "FR" and HT40 enabled.
Since we now have a helper which parses the triplets in intermediate
steps we now take care extra care to process padding.
Reported-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The max power from each country IE triplet was being ignored.
This fix isn't critical as CRDA was always being used for the lower
limit, but we should process it in case the AP still wants to
decrease power output even more for whatever reason.
Reported-by: Benoit PAPILLAULT <benoit.papillault@free.fr>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of sprinkling code with ifdef's define REG_DBG_PRINT() instead.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a syntax error when setting up the user regulatory
hint. This change yields the same exact binary object though
so it ends up just being a syntax typo fix, fortunately.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch provides infrastructure for machine translation of the
regulatory rules database used by CRDA into a C data structure.
It includes code for searching that database as an alternative
to dynamic regulatory rules updates via CRDA. Most people should
use CRDA instead of this infrastructure, but it provides a better
alternative than the WIRELESS_OLD_REGULATORY infrastructure (which
can now be removed).
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update "US" and "JP" for current rules, and replace "EU" rules with the
world roaming domain (since it was only a pseudo-domain anyway).
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've accumulated a number of options for wiphys
which make more sense as flags as we keep adding
more. Convert the existing ones.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the max_bandwidth attribute. It is only ever
written to, and is duplicated by max_bandwidth_khz in the
regulatory code.
Signed-off-by: Pat Erley <pat-lkml@erley.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the bss is always set now once we are connected, if the
bss has its own information element we refer to it and pass that
instead of relying on mac80211's parsing.
Now all cfg80211 drivers get country IE support, automatically and
we reduce the call overhead that we had on mac80211 which called this
upon every beacon and instead now call this only upon a successfull
connection by a STA on cfg80211.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We change regulatory code to be protected by its own regulatory
mutex and alleviate cfg80211_mutex to only be used to protect
cfg80211_rdev_list, the registered device list.
By doing this we will be able to work on regulatory core components
without having to have hog up the cfg80211_mutex. An example here is
we no longer need to use the cfg80211_mutex during driver specific
wiphy_apply_custom_regulatory(). We also no longer need it for the
the country IE regulatory hint; by doing so we end up curing this
new lockdep warning:
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.31-rc4-wl #12
-------------------------------------------------------
phy1/1709 is trying to acquire lock:
(cfg80211_mutex){+.+.+.}, at: [<ffffffffa00af852>] regulatory_hint_11d+0x32/0x3f0 [cfg80211]
but task is already holding lock:
(&ifmgd->mtx){+.+.+.}, at: [<ffffffffa0144228>] ieee80211_sta_work+0x108/0x10f0 [mac80211]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 (&ifmgd->mtx){+.+.+.}:
[<ffffffff810857b6>] __lock_acquire+0xd76/0x12b0
[<ffffffff81085dd3>] lock_acquire+0xe3/0x120
[<ffffffff814eeae4>] mutex_lock_nested+0x44/0x350
[<ffffffffa0141bb8>] ieee80211_mgd_auth+0x108/0x1f0 [mac80211]
[<ffffffffa0148563>] ieee80211_auth+0x13/0x20 [mac80211]
[<ffffffffa00bc3a1>] __cfg80211_mlme_auth+0x1b1/0x2a0 [cfg80211]
[<ffffffffa00bc516>] cfg80211_mlme_auth+0x86/0xc0 [cfg80211]
[<ffffffffa00b368d>] nl80211_authenticate+0x21d/0x230 [cfg80211]
[<ffffffff81416ba6>] genl_rcv_msg+0x1b6/0x1f0
[<ffffffff81415c39>] netlink_rcv_skb+0x89/0xb0
[<ffffffff814169d9>] genl_rcv+0x29/0x40
[<ffffffff8141591d>] netlink_unicast+0x29d/0x2b0
[<ffffffff81416514>] netlink_sendmsg+0x214/0x300
[<ffffffff813e4407>] sock_sendmsg+0x107/0x130
[<ffffffff813e45b9>] sys_sendmsg+0x189/0x320
[<ffffffff81011f82>] system_call_fastpath+0x16/0x1b
[<ffffffffffffffff>] 0xffffffffffffffff
-> #2 (&wdev->mtx){+.+.+.}:
[<ffffffff810857b6>] __lock_acquire+0xd76/0x12b0
[<ffffffff81085dd3>] lock_acquire+0xe3/0x120
[<ffffffff814eeae4>] mutex_lock_nested+0x44/0x350
[<ffffffffa00ab304>] cfg80211_netdev_notifier_call+0x1a4/0x390 [cfg80211]
[<ffffffff814f3dff>] notifier_call_chain+0x3f/0x80
[<ffffffff81075a91>] raw_notifier_call_chain+0x11/0x20
[<ffffffff813f665a>] dev_open+0x10a/0x120
[<ffffffff813f59bd>] dev_change_flags+0x9d/0x1e0
[<ffffffff8144eb6e>] devinet_ioctl+0x6fe/0x760
[<ffffffff81450204>] inet_ioctl+0x94/0xc0
[<ffffffff813e25fa>] sock_ioctl+0x6a/0x290
[<ffffffff8111e911>] vfs_ioctl+0x31/0xa0
[<ffffffff8111ea9a>] do_vfs_ioctl+0x8a/0x5c0
[<ffffffff8111f069>] sys_ioctl+0x99/0xa0
[<ffffffff81011f82>] system_call_fastpath+0x16/0x1b
[<ffffffffffffffff>] 0xffffffffffffffff
-> #1 (&rdev->mtx){+.+.+.}:
[<ffffffff810857b6>] __lock_acquire+0xd76/0x12b0
[<ffffffff81085dd3>] lock_acquire+0xe3/0x120
[<ffffffff814eeae4>] mutex_lock_nested+0x44/0x350
[<ffffffffa00ac4d0>] cfg80211_get_dev_from_ifindex+0x60/0x90 [cfg80211]
[<ffffffffa00b21ff>] get_rdev_dev_by_info_ifindex+0x6f/0xa0 [cfg80211]
[<ffffffffa00b51eb>] nl80211_set_interface+0x3b/0x260 [cfg80211]
[<ffffffff81416ba6>] genl_rcv_msg+0x1b6/0x1f0
[<ffffffff81415c39>] netlink_rcv_skb+0x89/0xb0
[<ffffffff814169d9>] genl_rcv+0x29/0x40
[<ffffffff8141591d>] netlink_unicast+0x29d/0x2b0
[<ffffffff81416514>] netlink_sendmsg+0x214/0x300
[<ffffffff813e4407>] sock_sendmsg+0x107/0x130
[<ffffffff813e45b9>] sys_sendmsg+0x189/0x320
[<ffffffff81011f82>] system_call_fastpath+0x16/0x1b
[<ffffffffffffffff>] 0xffffffffffffffff
other info that might help us debug this:
3 locks held by phy1/1709:
#0: ((wiphy_name(local->hw.wiphy))){+.+.+.}, at: [<ffffffff8106b45d>] worker_thread+0x19d/0x340
#1: (&ifmgd->work){+.+.+.}, at: [<ffffffff8106b45d>] worker_thread+0x19d/0x340
#2: (&ifmgd->mtx){+.+.+.}, at: [<ffffffffa0144228>] ieee80211_sta_work+0x108/0x10f0 [mac80211]
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify the country IE hint code by just bailing out if
a previous country IE has been issued. We currently just trust
the first AP we connect to on any card. The idea was to perform
conflict resolution within this routine but since we can no longer
iterate over the registered device list here we leave conflict
resolution to be dealt with at a later time on the workqueue.
This code has no functional changes other than saving us an
interation over the registered device list when a second card
is connected, or you unplug and connect the same one, and a
country IE is received. This would have been done upon every
beacon received.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has no functional changes.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A regression was added through patch a4ed90d6:
"cfg80211: respect API on orig_flags on channel for beacon hint"
We did indeed respect _orig flags but the intention was not clearly
stated in the commit log. This patch fixes firmware issues picked
up by iwlwifi when we lift passive scan of beaconing restrictions
on channels its EEPROM has been configured to always enable.
By doing so though we also disallowed beacon hints on devices
registering their wiphy with custom world regulatory domains
enabled, this happens to be currently ath5k, ath9k and ar9170.
The passive scan and beacon restrictions on those devices would
never be lifted even if we did find a beacon and the hardware did
support such enhancements when world roaming.
Since Johannes indicates iwlwifi firmware cannot be changed to
allow beacon hinting we set up a flag now to specifically allow
drivers to disable beacon hints for devices which cannot use them.
We enable the flag on iwlwifi to disable beacon hints and by default
enable it for all other drivers. It should be noted beacon hints lift
passive scan flags and beacon restrictions when we receive a beacon from
an AP on any 5 GHz non-DFS channels, and channels 12-14 on the 2.4 GHz
band. We don't bother with channels 1-11 as those channels are allowed
world wide.
This should fix world roaming for ath5k, ath9k and ar9170, thereby
improving scan time when we receive the first beacon from any AP,
and also enabling beaconing operation (AP/IBSS/Mesh) on cards which
would otherwise not be allowed to do so. Drivers not using custom
regulatory stuff (wiphy_apply_custom_regulatory()) were not affected
by this as the orig_flags for the channels would have been cleared
upon wiphy registration.
I tested this with a world roaming ath5k card.
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were treating ieee80211_regdom module parameter hints
as core hints, this means we were not letting the user help
compliance further when using the module parameter. It also
meant that users with a device with a custom regulatory
domain set (wiphy->custom_regulatory) using this module
parameter were being stuck to the original default core
static regualtory domain. We fix this by using the static
cfg80211_regdomain alpha2 as the core hint and treating the
module parameter separately.
All iwlwifi and ath5k/ath9k/ar9170 devices which world roam
set the wiphy->custom_regulatory. This change allows users
using this module parameter to have it trated as a a proper
user hint and not have it ignored.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've named the registered devices 'drv' sometimes,
thinking of "driver", which is not what it is, it's
the internal representation of a wiphy, i.e. a
device. Let's clean up the naming once and and use
'rdev' aka 'registered device' everywhere.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes an incorrect assumption (BUG_ON) made in
cfg80211 when handling country IE regulatory requests.
The assumption was that we won't try to call_crda()
twice for the same event and therefore we will not
recieve two replies through nl80211 for the regulatory
request. As it turns out it is true we don't call_crda()
twice for the same event, however, kobject_uevent_env()
*might* send the udev event twice and/or userspace can
simply process the udev event twice. We remove the BUG_ON()
and simply ignore the duplicate request.
For details refer to this thread:
http://marc.info/?l=linux-wireless&m=124149987921337&w=2
Cc: stable@kernel.org
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Device drivers using wiphy_apply_custom_regulatory() want some
regulatory settings applied to their wiphy, if no bands were
configured on the wiphy then something went wrong.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a race on access to last_request and its alpha2
through reg_is_valid_request() and us possibly processing
first another regulatory request on another CPU. We avoid
this improbably race by locking with the cfg80211_mutex as
we should have done in the first place. While at it add
the assert on locking on reg_is_valid_request().
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is more consistent with our nl80211 naming convention
for HT40-/+.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are not correctly listening to the regulatory max bandwidth
settings. To actually make use of it we need to redesign things
a bit. This patch does the work for that. We do this to so we
can obey to regulatory rules accordingly for use of HT40.
We end up dealing with HT40 by having two passes for each channel.
The first check will see if a 20 MHz channel fits into the channel's
center freq on a given frequency range. We check for a 20 MHz
banwidth channel as that is the maximum an individual channel
will use, at least for now. The first pass will go ahead and
check if the regulatory rule for that given center of frequency
allows 40 MHz bandwidths and we use this to determine whether
or not the channel supports HT40 or not. So to support HT40 you'll
need at a regulatory rule that allows you to use 40 MHz channels
but you're channel must also be enabled and support 20 MHz by itself.
The second pass is done after we do the regulatory checks over
an device's supported channel list. On each channel we'll check
if the control channel and the extension both:
o exist
o are enabled
o regulatory allows 40 MHz bandwidth on its frequency range
This work allows allows us to idependently check for HT40- and
HT40+.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Its possible for cfg80211 to have scheduled the work and for
the global workqueue to not have kicked in prior to a cfg80211
driver's regulatory hint or wiphy_apply_custom_regulatory().
Although this is very unlikely its possible and should fix
this race. When this race would happen you are expected to have
hit a null pointer dereference panic.
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 0ad8acaf "cfg80211: fix NULL pointer deference in
reg_device_remove()" added a check that last_request is non-NULL,
rendering the 2nd check superfluous. While there, rearrange the code a
bit so it's a little more straight forward.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We forgot to lock using the cfg80211_mutex in
wiphy_apply_custom_regulatory(). Without the lock
there is possible race between processing a reply from CRDA
and a driver calling wiphy_apply_custom_regulatory(). During
the processing of the reply from CRDA we free last_request and
wiphy_apply_custom_regulatory() eventually accesses an
element from last_request in the through freq_reg_info_regd().
This is very difficult to reproduce (I haven't), it takes us
3 hours and you need to be banging hard, but the race is obvious
by looking at the code.
This should only affect those who use this caller, which currently
is ath5k, ath9k, and ar9170.
EIP: 0060:[<f8ebec50>] EFLAGS: 00210282 CPU: 1
EIP is at freq_reg_info_regd+0x24/0x121 [cfg80211]
EAX: 00000000 EBX: f7ca0060 ECX: f5183d94 EDX: 0024cde0
ESI: f8f56edc EDI: 00000000 EBP: 00000000 ESP: f5183d44
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process modprobe (pid: 14617, ti=f5182000 task=f3934d10 task.ti=f5182000)
Stack: c0505300 f7ca0ab4 f5183d94 0024cde0 f8f403a6 f8f63160 f7ca0060 00000000
00000000 f8ebedf8 f5183d90 f8f56edc 00000000 00000004 00000f40 f8f56edc
f7ca0060 f7ca1234 00000000 00000000 00000000 f7ca14f0 f7ca0ab4 f7ca1289
Call Trace:
[<f8ebedf8>] wiphy_apply_custom_regulatory+0x8f/0x122 [cfg80211]
[<f8f3f798>] ath_attach+0x707/0x9e6 [ath9k]
[<f8f45e46>] ath_pci_probe+0x18d/0x29a [ath9k]
[<c023c7ba>] pci_device_probe+0xa3/0xe4
[<c02a860b>] really_probe+0xd7/0x1de
[<c02a87e7>] __driver_attach+0x37/0x55
[<c02a7eed>] bus_for_each_dev+0x31/0x57
[<c02a83bd>] driver_attach+0x16/0x18
[<c02a78e6>] bus_add_driver+0xec/0x21b
[<c02a8959>] driver_register+0x85/0xe2
[<c023c9bb>] __pci_register_driver+0x3c/0x69
[<f8e93043>] ath9k_init+0x43/0x68 [ath9k]
[<c010112b>] _stext+0x3b/0x116
[<c014a872>] sys_init_module+0x8a/0x19e
[<c01049ad>] sysenter_do_call+0x12/0x21
[<ffffe430>] 0xffffe430
=======================
Code: 0f 94 c0 c3 31 c0 c3 55 57 56 53 89 c3 83 ec 14 8b 74 24 2c 89 54 24 0c 89 4c 24 08 85 f6 75
06 8b 35 c8 bb ec f8 a1 cc bb ec f8 <8b> 40 04 83 f8 03 74 3a 48 74 37 8b 43 28 85 c0 74 30 89 c6
8b
EIP: [<f8ebec50>] freq_reg_info_regd+0x24/0x121 [cfg80211] SS:ESP 0068:f5183d44
Cc: stable@kernel.org
Reported-by: Nataraj Sadasivam <Nataraj.Sadasivam@Atheros.com>
Reported-by: Vivek Natarajan <Vivek.Natarajan@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trying to separate header files into net/wireless.h and
net/cfg80211.h has been a source of confusion. Remove
net/wireless.h (because there also is the linux/wireless.h)
and subsume everything into net/cfg80211.h -- except the
definitions for regulatory structures which get moved to
a new header net/regulatory.h.
The "new" net/cfg80211.h is now divided into sections.
There are no real changes in this patch but code shuffling
and some very minor documentation fixes.
I have also, to make things reflect reality, put in a
copyright line for Luis to net/regulatory.h since that
is probably exclusively written by him but was formerly
in a file that only had my copyright line.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This informs userspace when a change has occured on a world
roaming wiphy's channel which has lifted some restrictions
due to a regulatory beacon hint.
Because this is now sent to userspace through the regulatory
multicast group we remove the debug prints we used to use as
they are no longer necessary.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of our documented API we always respect the orig_flag
settings on a channel. We forgot to follow this for the beacon
hints.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We won't ever get here as regulatory_hint_core() can only fail
on -ENOMEM and in that case we don't initialize cfg80211 but this is
technically correct code.
This is actually good for stable, where we don't check for -ENOMEM
failure on __regulatory_hint()'s failure.
Cc: stable@kernel.org
Reported-by: Quentin Armitage <Quentin@armitage.org.uk>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We had left in code to allow interested developers to add
support for parsing country IEs when OLD_REG was enabled.
This never happened and since we're going to remove OLD_REG
lets just remove these comments and code for it.
This code path was never being entered so this has no
functional change.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems a few users are using this module parameter although its not
recommended. People are finding it useful despite there being utilities
for setting this in userspace. I'm not aware of any distribution using
this though.
Until userspace and distributions catch up with a default userspace
automatic replacement (GeoClue integration would be nirvana) we copy
the ieee80211_regdom module parameter from OLD_REG to the new reg
code to help these users migrate.
Users who are using the non-valid ISO / IEC 3166 alpha "EU" in their
ieee80211_regdom module parameter and migrate to non-OLD_REG enabled
system will world roam.
This also schedules removal of this same ieee80211_regdom module
parameter circa March 2010. Hope is by then nirvana is reached and
users will abandoned the module parameter completely.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The incorrect assumption is the last regulatory request
(last_request) is always a country IE when processing
country IEs. Although this is true 99% of the time the
first time this happens this could not be true.
This fixes an oops in the branch check for the last_request
when accessing drv_last_ie. The access was done under the
assumption the struct won't be null.
Note to stable: to port to 29 replace as follows, only 29 has
country IE code:
s|NL80211_REGDOM_SET_BY_COUNTRY_IE|REGDOM_SET_BY_COUNTRY_IE
Cc: stable@kernel.org
Reported-by: Quentin Armitage <Quentin@armitage.org.uk>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Although EU is a bogus alpha2 we need to process the send request
as our code depends on last_request being set.
Cc: stable@kernel.org
Reported-by: Quentin Armitage <Quentin@armitage.org.uk>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows us to send to userspace "regulatory" events.
For now we just send an event when we change regulatory domains.
We also notify userspace when devices are using their own custom
world roaming regulatory domains.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do this so we can later inform userspace who set the
regulatory domain and provide details of the request.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not used as we can always just assume the first
regulatory domain set will _always_ be a static regulatory
domain. REGDOM_SET_BY_CORE will be the first request from
cfg80211 for a regdomain and that then populates the first
regulatory request.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the lowest value amongst countries which do enable 5 GHz operation.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
freq_diff is unsigned, so test before subtraction
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we already have a regulatory request from the workqueue use that
and avoid a new kzalloc()
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were passing value by value, lets just pass the struct.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When devices are world roaming they cannot beacon or do active scan
on 5 GHz or on channels 12, 13 and 14 on the 2 GHz band. Although
we have a good regulatory API some cards may _always_ world roam, this
is also true when a system does not have CRDA present. Devices doing world
roaming can still passive scan, if they find a beacon from an AP on
one of the world roaming frequencies we make the assumption we can do
the same and we also remove the passive scan requirement.
This adds support for providing beacon regulatory hints based on scans.
This works for devices that do either hardware or software scanning.
If a channel has not yet been marked as having had a beacon present
on it we queue the beacon hint processing into the workqueue.
All wireless devices will benefit from beacon regulatory hints from
any wireless device on a system including new devices connected to
the system at a later time.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current static world regulatory domain is too restrictive,
we can use some 5 GHz channels world wide so long as they do not
touch frequencies which require DFS. The compromise is we must
also enforce passive scanning and disallow usage of a mode of
operation that beacons: (AP | IBSS | Mesh)
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This enables active scan and beaconing on Channels 1 through 11
on the static world regulatory domain.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows drivers that agree on regulatory to share their
regulatory domain.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All regulatory hints (core, driver, userspace and 11d) are now processed in
a workqueue.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was never happening but it was still wrong, so correct it.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Truth of the matter this was confusing people so mark it as
unlikely as that is the case now.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were not protecting last_request there is a small possible race
between an 11d hint and another routine which calls reset_regdomains()
which can prevent a valid country IE from being processed. This is
not critical as it will still be procesed soon after but locking prior
to it is correct.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do this so later on we can move the pending requests onto a
workqueue. By using the wiphy_idx instead of the wiphy we can
later easily check if the wiphy has disappeared or not.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calling kobject_uevent_env() can fail mainly due to out of
memory conditions. We do not want to continue during such
conditions so propagate that as well instead of letting
cfg80211 load as if everything is peachy.
Additionally lets clarify that when CRDA is not called during
cfg80211's initialization _and_ if the error is not an -ENOMEM
its because kobject_uevent_env() failed to call CRDA, not because
CRDA failed. For those who want to find out why we also let you
do so by enabling the kernel config CONFIG_CFG80211_REG_DEBUG --
you'll get an actual stack trace.
So for now we'll treat non -ENOMEM kobject_uevent_env() failures as
non fatal during cfg80211's initialization.
CC: Greg KH <greg@kroah.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes the core hint path more readable and allows for us to
later make it obvious under what circumstances we need locking or not.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211_drv_mutex is protecting more than the driver list,
this renames it and documents what its currently supposed to
protect.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This lets userspace request to get the currently set
regulatory domain.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let users be more compliant if so desired.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows drivers to request strict regulatory settings to
be applied to its devices. This is desirable for devices where
proper calibration and compliance can only be gauranteed for
for the device's programmed regulatory domain. Regulatory
domain settings will be ignored until the device's own
regulatory domain is properly configured. If no regulatory
domain is received only the world regulatory domain will be
applied -- if OLD_REG (default to "US") is not enabled. If
OLD_REG behaviour is not acceptable to drivers they must
update their wiphy with a custom reuglatory prior to wiphy
registration.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers may need more information than just who set the last regulatory domain,
as such lets just pass the last regulatory_request receipt. To do this we need
to move out to headers struct regulatory_request, and enum environment_cap. While
at it lets add documentation for enum environment_cap.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ensures that the initial REGDOM_SET_BY_CORE upon wiphy registration
respects the wiphy->custom_regulatory setting. Without this and if OLD_REG
is disabled (which will be default soon as we remove it) the
wiphy->custom_regulatory is simply ignored.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers without firmware can also have custom regulatory maps
which do not map to a specific ISO / IEC alpha2 country code.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We ignore regulatory hints for the same alpha2 if we already
have processed the same alpha2 on the current regulatory domain.
For a driver regulatory_hint() this means we copy onto its
wiphy->regd the previously procesed regulatory domain from CRDA
without having to call CRDA again.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This prevents user regulatory changes to be considered prior to previous
pending user, core or driver requests which have not be applied.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can be used by drivers on the reg_notifier()
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds wiphy_apply_custom_regulatory() to be used by drivers
prior to wiphy registration to apply a custom regulatory domain.
This can be used by drivers that do not have a direct 1-1 mapping
between a regulatory domain and a country.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We add support for multiple drivers to provide a regulatory_hint()
on a system by adding a wiphy specific regulatory domain cache.
This allows drivers to keep around cache their own regulatory domain
structure queried from CRDA.
We handle conflicts by intersecting multiple regulatory domains,
each driver will stick to its own regulatory domain though unless
a country IE has been received and processed.
If the user already requested a regulatory domain and a driver
requests the same regulatory domain then simply copy to the
driver's regd the same regulatory domain and do not call
CRDA, do not collect $200.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are calling the reg_notifier() callback per band, this is
not necessary, just call it once.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When CONFIG_CFG80211_REG_DEBUG is enabled and an intersection
occurs we are printing the regulatory domain passed by CRDA
and indicating its the intersected regulatory domain. Lets fix
this and print the intersection as originally intended.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes two issues with the sanity check loop when processing
the country IE:
1. Do not use frequency for the current subband channel check,
this was a big fat typo.
2. Apply the 5 GHz 4-channel steps when considering max channel
on each subband as was done with a recent patch.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The country IE number of channels on 5 GHz specifies the number
of 5 GHz channels, not the number of sequential channel numbers.
For example, if in a country IEs if the first channel given is 36
and the number of channels passed is 4 then the individual channel
numbers defined for the 5 GHz PHY by these parameters
are: 36, 40, 44, 48
not: 36, 37, 38, 39
See: http://tinyurl.com/11d-clarification
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a regression on disallowing bands introduced with the new
802.11d support. The issue is that IEEE-802.11 allows APs to send
a subset of what a country regulatory domain defines. This was clarified
in this document:
http://tinyurl.com/11d-clarification
As such it is possible, and this is what is done in practice, that a
single band 2.4 GHz AP will only send 2.4 GHz band regulatory information
through the 802.11 country information element and then the current
intersection with what CRDA provided yields a regulatory domain with
no 5 GHz information -- even though that country may actually allow
5 GHz operation. We correct this by only applying the intersection rules
on a channel if the the intersection yields a regulatory rule on the
same band the channel is on.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows us to make more wiphy specific judgements when
handling the channels later on.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This "fixes" the 11d oops I was seeing. This needs some more work but I
cannot work on it now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes the segfault I just pointed out.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds API to cfg80211 to allow wireless drivers to inform
us if their firmware can handle regulatory considerations *and*
they cannot map these regulatory domains to an ISO / IEC 3166
alpha2. In these cases we skip the first regulatory hint instead
of expecting the driver to build their own regulatory structure,
providing us with an alpha2, or using the reg_notifier().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds country IE parsing to mac80211 and enables its usage
within the new regulatory infrastructure in cfg80211. We parse
the country IEs only on management beacons for the BSSID you are
associated to and disregard the IEs when the country and environment
(indoor, outdoor, any) matches the already processed country IE.
To avoid following misinformed or outdated APs we build and use
a regulatory domain out of the intersection between what the AP
provides us on the country IE and what CRDA is aware is allowed
on the same country.
A secondary device is allowed to follow only the same country IE
as it make no sense for two devices on a system to be in two
different countries.
In the case the AP is using country IEs for an incorrect country
the user may help compliance further by setting the regulatory
domain before or after the IE is parsed and in that case another
intersection will be performed.
CONFIG_WIRELESS_OLD_REGULATORY is supported but requires CRDA
present.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Lets remain consistent and mark rds with > NL80211_MAX_SUPP_REG_RULES
number of reg rules as invalid in is_valid_rd().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
kobject_uevent_env() can return an error but it just tells us
if the uvent was built/sent or not, it doesn't tell us anything
about what happened in userspace, whether the udev rule was present
nor does it tell us if CRDA was present or not. So remove
the informative complaint about it assuming it will tell us
such things.
Note that you can determine if CRDA is present after loading cfg80211
by using:
is_old_static_regdom(cfg80211_regdomain)
but this doesn't account for possible user install after initial
boot, and also for when the user uses the static EU regulatory
domain.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When intersecting it is possible that set_regdom() was called
with a regulatory domain which we'll only use as an aid to
build a final regulatory domain.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So far the __set_regdom() code is pretty generic as the
intersection case is fairly straight forward; this will however
change when 802.11d support is added so lets separate intersection
code for now in preparation for 802.11d support.
This patch only has slight functional changes.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have control over the REGDOM_SET_BY_* macros passed
so remove the switch.
This patch has no functional changes.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have complete control over REGDOM_SET_BY_* enum passed
down to __regulatory_hint() as such there is no need to
account for unexpected REGDOM_SET_BY_*'s, lets just remove
the switch statement as this code does not change and
won't change even when we add 802.11d support.
This patch has no functional changes.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Regulatory rules with negative frequencies are now
marked as invalid in is_valid_reg_rule().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As regulatory_request gets bigger there will be more questions
of what things means, so clarify documenation for it and
keep track of the special alpha2 codes we use internally
and on the userspace regulatory agents.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are certain scenerios where we require intersecting
two regulatory domains. This adds intersection support.
When we enable 802.11d support we will use this to intersect
the regulatory domain from the AP's country IE and what our
regulatory agent believes is correct for a country.
This patch enables intersection for now in the case where
the last regdomain was set by a country IE which was parsed
and the user then wants to set the regulatory domain. Since
we don't support country IE parsing yet this code path will not
be hit, however this allows us to pave the way for 11d support.
Intersection code has been tested in userspace with CRDA.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A regulatory rule is invalid when the frequency difference
between the end of the frequency range and the start is 0.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function is only used once, move it closer to its caller.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function has a few WARNs that may eventually trigger
when an AP sends rogue beacons, those must be removed. Some
of the comments in the function are also inappropriate as
this function is concerned with the global hint, not a per-
wiphy thing (which a multidomain flag on a wiphy would imply).
I'm convinced that we don't need to do anything to implement
multi-domain capability as 802.11-2007 specifies it because
it makes only two things mandatory:
* starting of BSS/IBSS must have country information
(this can easily be done with a mac80211 patch)
* a STA must adopt the country information (we already have
the framework for this)
But we don't have anything implemented anyway for now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code needs to be split out and cleaned up, so as a
first step remove the capability, to add it back in a
subsequent patch as a separate function. Also remove the
publically facing return value of the function and the
wiphy argument. A number of internal functions go from
being generic helpers to just being used for alpha2
setting.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The regdom struct is given to the core, so it might as well
free it in error conditions.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We really only need to know the last request at each point in time.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This mutex is wrong, we use cfg80211_drv_mutex (which should
possibly be renamed to just cfg80211_mutex) everywhere except
in one place, fix that and get rid of the extra mutex.
Also get rid of a spurious regulatory_requests list definition.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The statically defined regdomains are used in a very convoluted
way, use them instead to prime the information we have and then
continue operating normally.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few pointers and structures in the regulatory code are const,
but because it wasn't done properly a whole bunch of bogus
casts were needed to compile without warning. Mark everything
const properly to avoid that kind of junk code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent code from Luis is an #ifdef hell and contains lots of
code that's stuffed into the wrong file making a whole bunch of
things needlessly non-static, and besides, what is it doing in
core.c??
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the new wireless regulatory infrastructure. The
main motiviation behind this was to centralize regulatory
code as each driver was implementing their own regulatory solution,
and to replace the initial centralized code we have where:
* only 3 regulatory domains are supported: US, JP and EU
* regulatory domains can only be changed through module parameter
* all rules were built statically in the kernel
We now have support for regulatory domains for many countries
and regulatory domains are now queried through a userspace agent
through udev allowing distributions to update regulatory rules
without updating the kernel.
Each driver can regulatory_hint() a regulatory domain
based on either their EEPROM mapped regulatory domain value to a
respective ISO/IEC 3166-1 country code or pass an internally built
regulatory domain. We also add support to let the user set the
regulatory domain through userspace in case of faulty EEPROMs to
further help compliance.
Support for world roaming will be added soon for cards capable of
this.
For more information see:
http://wireless.kernel.org/en/developers/Regulatory/CRDA
For now we leave an option to enable the old module parameter,
ieee80211_regdom, and to build the 3 old regdomains statically
(US, JP and EU). This option is CONFIG_WIRELESS_OLD_REGULATORY.
These old static definitions and the module parameter is being
scheduled for removal for 2.6.29. Note that if you use this
you won't make use of a world regulatory domain as its pointless.
If you leave this option enabled and if CRDA is present and you
use US or JP we will try to ask CRDA to update us a regulatory
domain for us.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement missing EU regulatory domain for mac80211. Based on the
information in IEEE 802.11-2007 (specifically pages 1142, 1143 & 1148)
and ETSI 301 893 (V1.4.1).
With thanks to Johannes Berg.
Signed-off-by: Tony Vroon <tony@linx.net>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds channels to US regulatory domain
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch creates new cfg80211 wiphy API for channel and bitrate
registration and converts mac80211 and drivers to the new API. The
old mac80211 API is completely ripped out. All drivers (except ath5k)
are updated to the new API, in many cases I expect that optimisations
can be done.
Along with the regulatory code I've also ripped out the
IEEE80211_HW_DEFAULT_REG_DOMAIN_CONFIGURED flag, I believe it to be
unnecessary if the hardware simply gives us whatever channels it wants
to support and we then enable/disable them as required, which is pretty
much required for travelling.
Additionally, the patch adds proper "basic" rate handling for STA
mode interface, AP mode interface will have to have new API added
to allow userspace to set the basic rate set, currently it'll be
empty... However, the basic rate handling will need to be moved to
the BSS conf stuff.
I do expect there to be bugs in this, especially wrt. transmit
power handling where I'm basically clueless about how it should work.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan