rt2x00usb_vendor_request_large_buff is write-only, so it is
safe to make the argument a const.
Fixes compile warning:
drivers/net/wireless/rt2x00/rt73usb.c: In function 'rt73usb_load_firmware':
drivers/net/wireless/rt2x00/rt73usb.c:916: warning: passing argument 5 of 'rt2x00usb_vendor_request_large_buff' discards qualifiers from pointer target typ
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In kernel version 2.6.26-rc9 my wireless LAN card worked; but in the
released 2.6.26, my RaLink rt2500 card wouldn't associate.
Git-bisect led me to this patch:
61486e0f68
rt2x00: Remove ieee80211_tx_control argument from write_tx_desc()
I believe that there is a problem with that patch --- it
(inadvertantly) removes an extra line of code, that used to set the
DATABYTE_COUNT field.
This patch reinstates that line, and with it my card works again.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sequence counter can be accessed in IRQ context,
which means the lock protecting the counter should
be irqsave. To prevent making the entire intf->lock irqsave
without reason, create a new lock which only protects
the sequence counter.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the EEPROM_BBPTUNE_VGC word is valid, we should
override EEPROM_BBPTUNE_VGCLOWER field with the BBP
value.
And we should _not_ do that when EEPROM_BBPTUNE_R17 is valid.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the hardware has indicated the firmware upload has completed
and the device is ready, we should wait another millisecond to
make sure the device is really ready to continue.
Without this timout, bringing the interface down and up again will
fail due to incorrect register initialization.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The if-statement to determine the new TX/RX antenna
configuration was incomplete. It lacks the general
else-clause when the antenna wasn't changed.
This is a correct event, since it can occur when only
one of the antenna's has been changed or when the new
configuration is being forced (like when the interface
has just been added).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Although most rt2x00 debugfs files don't contain
information which could compromise network security,
it is better to set the access permissions to root only.
This will be required when HW crypto is implemented,
because it could be possible to read the HW key from
the registers.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes mac80211 to not use the skb->cb over the queue step
from virtual interfaces to the master. The patch also, for now,
disables aggregation because that would still require requeuing,
will fix that in a separate patch. There are two other places (software
requeue and powersaving stations) where requeue can happen, but that is
not currently used by any drivers/not possible to use respectively.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the queues are being initialized the entry flags fields must be
reset to 0. When this does not happen some entries might still be
marked as "occupied" after an ifdown & ifup cycle which would trigger
errors when the entry is being accessed:
phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
Please file bug report to http://rt2x00.serialmonkey.com.
This also fixes the mac80211 warning:
------------[ cut here ]------------
WARNING: at net/mac80211/tx.c:1238 ieee80211_master_start_xmit+0x30a/0x350 [mac80211]()
which was triggered by the queue error.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00 will only perform configuration changes from
mac80211 when the configuration option has changed.
This means it keeps track of the current active configuration
and will check these values when the config() callback function
is used.
However this causes breakage when the interface has been
brought down and up again, since all stored active values
aren't reset while the registers might have.
This is for example the case with rt61pci antenna registers which
will jump to invalid values when the interface has been started.
To make sure a full configuration takes place after the start()
callback function, a new flag is added which will be checked
during config() and skips the "what's changed" phase.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending the RTS/CTS frame fails, we should
free the skb buffer which was created.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When IEEE80211_TX_CTL_ASSIGN_SEQ is not set,
the driver should disable hardware sequence counting
to make sure the mac80211 provided counter is used.
This fixes QOS sequence counting, since that is one
of the cases where mac80211 provides a seperate
sequence counter.
By moving the sequence counting code to rt2x00queue
we make sure that _all_ frames get the sequence counter,
including RTS/CTS and Beacon frames.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When setting up a beacon template, the length of the beacon is
calculated with the assumption that the SKB already contains
the Tx descriptor. In the case of beacons it doesn't.
This patch undoes the damage by adding the Tx descriptor length
to the beacon length. This is safe, because the shortest possible
beacon is longer than the Tx header.
Signed-off-by: Iwo Mergler <Iwo@call-direct.com.au>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Switches rt73usb to use large vendor requests for firmware
and beacons. This also fixes the garbled beacon bug.
Signed-off-by: Iwo Mergler <Iwo@call-direct.com.au>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adds an extra rt2x00 vendor request function to support register
transfers beyond the CSR_CACHE_SIZE / USB packet size limit. This
is useful for firmware uploads, beacon templates and keys, all
of which are to large to do with a single USB request.
Signed-off-by: Iwo Mergler <Iwo@call-direct.com.au>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Olivier reported a difference between the EIFS
values used in the legacy driver and the one in
the rt2x00 drivers.
In rt2x00 the value was
( SIFS + (8 * (IEEE80211_HEADER + ACK_SIZE)) )
which comes down to 314us while the legacy driver uses the value 364us
This was caused because EIFS is: SIFS + DIFS + AckTime
This patch will fix this by adding the DIFS by the above value,
and creating a SHORT_EIFS define which uses the SHORT_DIFS.
Reported-by: Olivier Cornu <o.cornu@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I forgot this in the previous patch that made it unused.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I removed the special "default" meaning from the QoS
parameters, I forgot to update drivers and this lead to
warnings because some drivers were checking for the special
values and putting in defaults. This fixes that by removing
the default special-casing completely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the legacy drivers the LED association status
must be reset after the firmware has been uploaded to the
hardware.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes mac80211 assign proper sequence numbers to
QoS-data frames. It also removes the old sequence number code
because we noticed that only the driver or hardware can assign
sequence numbers to non-QoS-data and especially management
frames in a race-free manner because beacons aren't passed
through mac80211's TX path.
This patch also adds temporary code to the rt2x00 drivers to
not break them completely, that code will have to be reworked
for proper sequence numbers on beacons.
It also moves sequence number assignment down in the TX path
so no sequence numbers are assigned to frames that are dropped.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the new beacon handling from mac80211 we can
reorganize the beacon handling in rt2x00 as well.
This patch will move the function to the TX handlers,
and move all duplicate code into rt2x00queue.c.
After this change the descriptor helper functions
from rt2x00queue.c no longer need to be exported
outside of rt2x00lib and can be declared static.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inform drivers about the changed CTS protection settings.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes mac80211's beacon configuration handling
to never pass skbs to the driver directly but rather always
require the driver to use ieee80211_beacon_get(). Additionally,
it introduces "change flags" on the config_interface() call
to enable drivers to figure out what is changing. Finally, it
removes the beacon_update() driver callback in favour of
having IBSS beacon delivered by ieee80211_beacon_get() as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As soon as an interface is enabled, and that interface is in adhoc or master mode,
the device will start raising beacondone interrupts. But before the first interrupt is
raised, mac80211 will probably not have send any beacons to the device yet, which
results in a NULL pointer error when the skb is being freed.
Note that the "raise beacondone interrupts without a beacon" is also a bug,
and will be addressed later. The more important bug however is preventing
the NULL pointer failt itself, since there might be other conditions that could trigger
it as well.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As soon as init_registers() was called, the rt2400/rt2500
would start raising beacondone interrupts. Since this is highly
premature since no beacons were provided yet, we should
initialize the synchronization register to 0.
This will make all drivers initialize it to 0 regardless
if they are raising beacondone interrupts or not, since it only
makes sense to have it completely disabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix some register documentation in the register header files.
This allows better parsing by userspace scripts which in turn
helps debugging.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2400 is the only currently available rt2x00 driver which
supports reporting of the RX end time for frames.
Since mac80211 uses this information for IBSS syncing, it
is important that it is being reported.
v2: Complement 32 bits of RX timestamp with upper 32bits from TSF
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the rt2x00 singlethreaded workqueue and move
the link tuner and packet filter scheduled work to
the ieee80211_hw->workqueue again.
The only exception is the interface scheduled work
handler which uses the mac80211 interface iterator
under the RTNL lock. This work needs to be handled
on the kernel workqueue to prevent lockdep issues.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We only need 4 bytes of headroom for alignment
purposes in the RX frame. It was previously higher
for optimization purposes which are no longer
possible due to DMA mappings.
v2: Fix patch error
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the new rfkill interface there is no longer a need
for the input_polldev. Create a delayed_work structure
which we can put on the mac80211 workqueue and poll the
hardware every 1000ms.
v2: Decrease poll frequency from 100ms to 1000ms
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a circular locking dependency in the workqueue handling.
The interface work task uses the mac80211 function
ieee80211_iterate_active_interfaces() which grabs the RTNL lock.
However when the interface is brough down, this happens under the RTNL
lock as well, this causes problems because mac80211 will flush the workqueue
during the ifdown event. This causes mac80211 to wait until the driver has
completed all work which can't finish because it is waiting on the RTNL lock.
This is fixed by moving rt2x00 workqueue tasks on a different workqueue,
this workqueue can be flushed when the ieee80211_hw structure is removed
by the driver (when the driver is unloaded) which does not happen under the
RTNL lock.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/b43/rfkill.o
drivers/net/wireless/b43/rfkill.c: In function ‘b43_rfkill_soft_toggle’:
drivers/net/wireless/b43/rfkill.c:90: warning: enumeration value ‘RFKILL_STATE_HARD_BLOCKED’ not handled in switch
CC [M] drivers/net/wireless/b43legacy/rfkill.o
drivers/net/wireless/b43legacy/rfkill.c: In function ‘b43legacy_rfkill_soft_toggle’:
drivers/net/wireless/b43legacy/rfkill.c:92: warning: enumeration value ‘RFKILL_STATE_HARD_BLOCKED’ not handled in switch
CC [M] drivers/net/wireless/iwlwifi/iwl-rfkill.o
drivers/net/wireless/iwlwifi/iwl-rfkill.c: In function ‘iwl_rfkill_soft_rf_kill’:
drivers/net/wireless/iwlwifi/iwl-rfkill.c:56: warning: enumeration value ‘RFKILL_STATE_HARD_BLOCKED’ not handled in switch
Also handle RFKILL_STATE_{ON,OFF} -> RFKILL_STATE_{UNBLOCKED,SOFT_BLOCKED}
conversion since I'm already here...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During rt2x00usb_disable_radio() all pending urb's should
be killed and not only those from the RX queue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rt2x00queue_alloc_rxskbs() fails rt2x00queue_unitialize()
will be called which will free all rxskb. So we don't need
to do this in the rt2x00queue_alloc_rxskb() function as well.
rt2x00queue_free_skb() unmaps the DMA but doesn't clear the
allocation flag. Since the code is copied from rt2x00queue_unmap_skb()
anyway (and that function does clear the flag) we might as well
use that function directly.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without the preallocated DMA we can now safely increase
the queue size withotu negative impact on the memory
requirements of rt2x00.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sparse produces warnings about nested contain_of() statements,
this means that lines like:
interface_to_usbdev(to_usb_interface(rt2x00dev->dev));
will upset sparse.
Add a new macro to rt2x00usb.h which will convert to device
structure to the usb_device pointer in 2 steps to prevent this
sparse warning.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With a bit of code moving to rt2x00lib within the
TX and RX paths we can now remove a lot of EXPORT_SYMBOL_GPL()
statements. This cleans up the interface between rt2x00lib
and the drivers and has the additional benefit that rt2x00pci
and rt2x00usb are trimmed down in size as well since they
have less to do.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current PCI drivers require a lot of pre-allocated DMA buffers. Reduce this
by using dynamically mapped skb's (using pci_map_single) instead of the pre-
allocated DMA buffers that are allocated at device start-up time.
At the same time move common RX path code into rt2x00lib from rt2x00pci and
rt2x00usb, as the RX paths now are now almost the same.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation of replacing the statically allocated DMA buffers with
dynamically mapped skbs, centralize the allocation of RX skbs to rt2x00queue.c
and let rt2x00pci already use them.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At the same time clean up the device administration a bit, by storing a pointer
to struct device instead of a void pointer that is dependent on the type of
device. The normal PCI and USB subsystem provided macros can be used to convert
the device pointer to the right type.
This makes the rt2x00 driver a bit more type-safe.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The skbs containing the beacons weren't properly cleaned up for rt2400pci, rt2500pci,
rt61pci, and rt73usb. Clean up those skbs in the manner appropriate for each driver.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn