Macro HISI_SAS_SGE_PAGE_CNT is defined to SG_CHUNK_SIZE, which is 128.
This means that sizeof(struct hisi_sas_slot_buf_table) is 4192. This is
just over a 4K, which can mean inefficient DMA memory usage (for no PI).
Reduce the size of HISI_SAS_SGE_PAGE_CNT to 124 to fit in a 4K page. With
this change, we experience no performance hit.
Cc: dann frazier <dann.frazier@canonical.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The argument of dev_err() called by multi_bit_ecc_error_process_v3_hw() is
not right. We pass two arguments, but there is only one printk format
specifier in the string.
Also move the print format string to dev_err().
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When removing the driver or when probe fails, we need to delete the PHY
timers.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace kmalloc + memcpy with kmemdup.
This was reported by coccinelle.
Signed-off-by: Bharath Vedartham <linux.bhar@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warnings:
drivers/scsi/megaraid/megaraid_sas_base.c: In function megasas_suspend:
drivers/scsi/megaraid/megaraid_sas_base.c:7269:20: warning: variable host set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_base.c: In function megasas_aen_polling:
drivers/scsi/megaraid/megaraid_sas_base.c:8397:15: warning: variable wait_time set but not used [-Wunused-but-set-variable]
'host' never used since introduction in commit 31ea708897 ("[SCSI]
megaraid_sas: add hibernation support")
'wait_time' never used since commit 11c71cb4ab ("megaraid_sas: Do
not allow PCI access during OCR")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/megaraid/megaraid_sas_base.c: In function megasas_transition_to_ready:
drivers/scsi/megaraid/megaraid_sas_base.c:3900:6: warning: variable cur_state set but not used [-Wunused-but-set-variable]
Never used since commit 7218df69e3 ("[SCSI] megaraid_sas: use the
firmware boot timeout when waiting for commands")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In _ctl_ioctl_main(), 'ioctl_header' is fetched the first time from
userspace. 'ioctl_header.ioc_number' is then checked. The legal result is
saved to 'ioc'. Then, in condition MPT3COMMAND, the whole struct is fetched
again from the userspace. Then _ctl_do_mpt_command() is called, 'ioc' and
'karg' as inputs.
However, a malicious user can change the 'ioc_number' between the two
fetches, which will cause a potential security issues. Moreover, a
malicious user can provide a valid 'ioc_number' to pass the check in first
fetch, and then modify it in the second fetch.
To fix this, we need to recheck the 'ioc_number' in the second fetch.
Signed-off-by: Gen Zhang <blackgod016574@gmail.com>
Acked-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently auto-hibernate is activated if host supports auto-hibern8
capability. However error-handling is not implemented, which makes the
feature somewhat risky.
If either "Hibernate Enter" or "Hibernate Exit" fail during auto-hibernate
flow, the corresponding interrupt "UIC_HIBERNATE_ENTER" or
"UIC_HIBERNATE_EXIT" shall be raised according to UFS specification.
This patch adds auto-hibernate error-handling:
- Monitor "Hibernate Enter" and "Hibernate Exit" interrupts after
auto-hibernate feature is activated.
- If a failure happens, trigger error-handling just like
"manual-hibernate" failure and apply the same recovery flow: schedule
UFS error handler in ufshcd_check_errors(), and then do host reset and
restore in UFS error handler.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some vendor-specific initialization flow may set its own auto-hibernate
timer. In this case, do not overwrite timer value as "default value" in
ufshcd_init().
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The checking of Auto-Hibernation support is used in many places in the
driver, thus re-factor it as ufshcd_is_auto_hibern8_supported() to make
code more clean.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Avri Altman <Avri.Altman@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since we are processing events synchronously now, the second call of
sas_ex_join_wide_port() in sas_ex_discover_dev() is not needed. There will
be no races with other works in disco workqueue. So remove the second
sas_ex_join_wide_port().
I did not change the return value of 'res' to error when discover failed
because we need to continue to discover other phys if one phy discover
failed. So let's keep that logic as before and just add a debug log to
detect the failure. And directly return if second fanout expander attatched
to the parent expander because it has nothing to do after the phy is
disabled.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use *_pool_zalloc rather than *_pool_alloc followed by memset with 0.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the check for a lockup_detected failure exits via the label
return_reset_status that reads and dereferences an uninitialized pointer
dev. Fix this by ensuring dev is inintialized to null.
Addresses-Coverity: ("Uninitialized pointer read")
Fixes: 14991a5bade5 ("scsi: hpsa: correct device resets")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix the following warning reported by coccicheck:
drivers/target/iscsi/iscsi_target_nego.c:175:6-8: WARNING: possible
condition with no effect (if == else)
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Reviewed-by: David Disseldorp <ddiss@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix abord to abort.
Signed-off-by: Weitao Hou <houweitaoo@gmail.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add PCMCIA card support to Future Domain SCSI driver.
Tested with IBM SCSI PCMCIA Adapter 40G1890.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add register bit definitions from documentation to header file and use them
instead of magic constants. No changes to generated binary.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After a successful SRP login response we call scsi_unblock_requests() to
kick any pending IOs. The callback to process this SRP response happens in
a tasklet and therefore is in softirq context. The result of such is that
when blk-mq is enabled, it is no longer safe to call scsi_unblock_requests()
from this context. The result of duing so triggers the following WARN_ON
splat in dmesg after a host reset or CRQ reenablement.
WARNING: CPU: 0 PID: 0 at block/blk-mq.c:1375 __blk_mq_run_hw_queue+0x120/0x180
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.0.0-rc8 #4
NIP [c0000000009771e0] __blk_mq_run_hw_queue+0x120/0x180
LR [c000000000977484] __blk_mq_delay_run_hw_queue+0x244/0x250
Call Trace:
__blk_mq_delay_run_hw_queue+0x244/0x250
blk_mq_run_hw_queue+0x8c/0x1c0
blk_mq_run_hw_queues+0x60/0x90
scsi_run_queue+0x1e4/0x3b0
scsi_run_host_queues+0x48/0x80
login_rsp+0xb0/0x100
ibmvscsi_handle_crq+0x30c/0x3e0
ibmvscsi_task+0x54/0xe0
tasklet_action_common.isra.3+0xc4/0x1a0
__do_softirq+0x174/0x3f4
irq_exit+0xf0/0x120
__do_irq+0xb0/0x210
call_do_irq+0x14/0x24
do_IRQ+0x9c/0x130
hardware_interrupt_common+0x14c/0x150
This patch fixes the issue by introducing a new host action for unblocking
the scsi requests in our seperate work thread.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current implemenation relies on two flags in the driver's private host
structure to signal the need for a host reset or to reenable the CRQ after
a LPAR migration. This patch does away with those flags and introduces a
single action flag and defined enums for the supported kthread work
actions. Lastly, the if/else logic is replaced with a switch statement.
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Wire up the host_reset function in our driver_template to allow a user
requested adpater reset via the host_reset sysfs attribute.
Example:
echo "adapter" > /sys/class/scsi_host/host0/host_reset
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update lpfc version to 12.2.0.3
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Kernel warnings may be seen with preempt debugging enabled.
Replace smp_processor_id calls with raw_smp_processor_id or cpu information
stored in hdwq structures.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Crashes in scsi_queue_rq or in dma_unmap_direct_sg during BFS when lpfc has
lpfc_enable_bg=1.
lpfc is setting DIX and prot sg after scsi_add_host_with_dma() has been
called. The scsi_host_set_prot() and scsi_host_set_guard() routines need to
be called before scsi_add_host_with_dma().
Revise the calling sequence to set the protection/guard data before calling
scsi_add_host_with_dma().
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
FDMI protocol support registration was not accurately showing nvme
support. The fcponly-path clears the parameter object.
Move the code out of the fcponly code path. Fix the FDMI registration data
to properly check for nvme support. Commonize the manner in which the fdmi
routines set protocol support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issuing a LUN reset was resulting in a command failure which then escalated
to a host reset.
The FCP-4 spec allows fcp_rsp_len field to specify the number of valid
bytes of FCP_RSP_INFO, and the value could be 4 or 8. The driver is
allowing only a value of 8, thus it failed the command.
Revise the driver to allow 4 or 8.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While fixing the resources per socket, realized the driver was not using
hardware queues (up to 1 per cpu) if there were fewer interrupt
vectors. The driver was only using the hardware queue assigned to the cpu
with the vector.
Rework the affinity map check to use the additional hardware queue elements
that had been allocated. If the cpu count exceeds the hardware queue count
- share, but choose what is shared with by: hyperthread peer, core peer,
socket peer, or finally similar cpu in a different socket.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver was coded expecting enough hardware queues and interrupt vectors
such that at least there was one per socket. In the case where there were
fewer than sockets, cpus were left unassigned thus null pointers.
Rework the affinity mappings. Map settings for the cpu's that are in the
irq cpu mask. For each cpu not in the mask, map to another cpu that does
have a mask. Choice of the "other" cpu will attempt to map to the same cpu
but differing hyperthread, or cpu within in same core, or cpu within same
socket, or finally cpu in the base socket.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Invalid logical speed is displayed for trunk enabled ports when all ports
are down. Also noted that link speed is incorrectly reported for the units
when links are up.
Current code is returning the logical link speed from the last event from
the adapter. In cases where the last link went down, the link speed in the
event was not valid - meaning that although the links where down the field
had a bogus value.
Rework the event handling to qualify the trunk link state before using the
event speed data.
Also correct units on other areas where the logical link speed was taken
from a link event.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
eq create is leaking mailbox memory if it encounters an error.
rework error path to free the memory.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver unconditionally says fw doesn't support nvme when in
truth it was a driver parameter settings that disabled nvme support.
Rework the code validating nvme support to accurately report what
condition is disabling nvme support. Save state on whether nvme
fw supports nvme in case sysfs attributes change dynamically.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a race condition with the abort handler declaring a waitq
item on it's stack, followed by a timeout in the abort handler that
has it give up on the abort return to its caller. When the io is
finally aborted and its completion handler called, it references
the waitq element that the abort_handler set up, which is no longer
valid resulting in a deadlock.
Fix by clearing the waitq reference, under lock, when the abort
handler timeout gives up. Have the completion handler validate the
waitq before referencing it.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When queued work is executed posting a new command to the transport
the driver is reporting a null buffer.
The driver had received an ABTS which matched a command that had
been scheduled for delivery to the transport. The driver proceeded
to cancel the command, but the work item was never cancelled.
Fix by cancelling the queued work item. Also turns out the ABTS
response was not properly sending a BA_ACC, so set the flag to
send the ACC.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use-after-free memory overwrite detected. Problem reported
by Ewan Milne at Red Hat after running lpfc target with additional
memory checking enabled.
Race condition when lpfc_nvmet_xmt_ls_rsp_cmp frees the ctxp
memory in interrupt context before lpfc_nvmet_xmt_ls_rsp
clears a field in the ctxp after successfully issuing the wqe.
Remove the unnecessary ctxp write after reposting the rq buffer. The
ctxp->rqb_buffer field is not checked in LS handling after the wqe
is submitted.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reported-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Under heavy load the target stops responding, the drivers aborts
timeout and we start recovery by logging out of the target, but
the target is never logged into again.
In a point-to-point scenario, there were battling PLOGI's. When we
received a PLOGI request after having sent one, the driver cancels
the processing of the original plogi. However, the completion path
of the remaining plogi was coded to skip the reg_rpi that should
be happening on the 2nd plogi.
Correct by adding a simple pt2pt check such that the 2nd plogi isn't
skipped and the reg_login occurs.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Turns out the message change in 12.2.0.1 for unsupported topology
makes the linux driver out of sync with other products.
Revert the message back to the prior content for product consistency.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver currently is relying on firmware to match ABTSs to existing
exchanges. This works fine as long as an exchange has been assigned to the
io and work posted to it. However, for unmapped frames (rxid=0xFFFF), the
driver has yet to assign an xri. The driver was blindly saying it couldn't
match the ABTS and sending the BA_xxx. However, the command frame may have
been in queues waiting on xri's before posting to the nvmet_fc layer. When
xri's became available, the command frame would still be pushed to the
transport and that io would execute, even though the io had been killed by
ABTS. The initiator, seeing the io ABTS'd, would reuse the exchange for a
different io which would be received on the target and pushed up. If the
"zombie" io then came back down and started transmitting, the initiator
would match the oxid and accept erroneous data. Bad things happened.
Add tracking of active exchanges in the target to allow matching of a
received ABTS against active or pending IO requests. If the ABTS is matched
to a pending or active IO, the drive initiates cleanup and conditionally
notifies the transport.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently the driver is notified of new command frame receipt by CQEs. As
part of the CQE processing, the driver upcalls the nvmet_fc transport to
deliver the command. nvmet_fc, as part of receiving the command builds out
a context for it, where one of the first steps is to allocate memory for
the io.
When running with tests that do large ios (1MB), it was found on some
systems, the total number of outstanding I/O's, at 1MB per, completely
consumed the system's memory. Thus additional ios were getting blocked in
the memory allocator. Given that this blocked the lpfc thread processing
CQEs, there were lots of other commands that were received and which are
then held up, and given CQEs are serially processed, the aggregate delays
for an IO waiting behind the others became cummulative - enough so that the
initiator hit timeouts for the ios.
The basic fix is to avoid the direct upcall and instead schedule a work
item for each io as it is received. This allows the cq processing to
complete very quickly, and each io can then run or block on it's own.
However, this general solution hurts latency when there are few ios. As
such, implemented the fix such that the driver watches how many CQEs it has
processed sequentially in one run. As long as the count is below a
threshold, the direct nvmet_fc upcall will be made. Only when the count is
exceeded will it revert to work scheduling.
Given that debug of this showed a surprisingly long delay in cq processing,
the io timer stats were updated to better reflect the processing of the
different points.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Revise a stalled adapter message to also include the number of jobs that
are stalling the thread.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A race condition resulted in receive buffers being placed in the free list
twice.
Change the locking and handling to check whether the "other" path will be
freeing the entry in a later thread and skip it if it is.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After receiving an unsolicited ABTS (meaning rxid is 0xFFFF), the driver
used the oxid from the initiator to match against a local xri which may
have been allocated for the io. The xri would be the rxid - it's an invalid
check resulting in the command not being matched or erroneously matched.
Change the lookup to use the oxid and the SID to match against received
IO's original values.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Softlockups are seen in low memory situations. They are due to doing
oas_lun allocation with GFP_KERNEL in atomic contexts.
Change the calls to oas_lun to indicate atomic context so that GFP_ATOMIC
is used.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Create a debugfs interface for megaraid_sas driver. Provide interface to
dump driver RAID map in debugfs.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Print FW supported MSI-X vector count only if FW supports
MSI-X.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add debug prints related to device list being returned by firmware. The a
debug flag to activate these prints.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add prints in resume/suspend path to help in debugging hibernation
issues. The print gives an indication when the driver entry points are
called.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a print to dump the interrupt status in system log for debugging.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When driver detects a firmware fault during load, dump additional
information on fault code and subcode that will help in debugging.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add a sysfs interface to get the raid map index that is being used by
driver.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add prints for BAR address information during driver load. This helps in
debugging issues with BAR address changing during OS boot.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
John Garry