If a regmap is using fast_io, allocate the scratch buffer in
regmap_bulk_write() with GFP_ATOMIC instead of GFP_KERNEL.
Otherwise we may schedule while atomic.
Reported-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
__regmap_init() may receive a NULL `struct regmap_bus *bus' pointer,
for example, from snd_hdac_regmap_init(), and it make sure that it
does not NULL deference `bus`, except around ->max_raw_read and
->max_raw_write initialisation. Add missing check.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When doing a bulk read from a device which lacks raw I/O support we fall
back to doing register at a time reads but we still use the raw
formatters in order to render the data into the word size used by the
device (since bulk reads still operate on the device word size rather
than unsigned ints). This means that devices without raw formatting
such as those that provide reg_read() are not supported. Provide
handling for them by copying the values read into native endian values
of the appropriate size.
Signed-off-by: Mark Brown <broonie@kernel.org>
This allows to read/write up to 32 bytes of data and is to be prefered
if supported before the register read/write smbus support.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check in regmap_raw_read() and regmap_raw_write() for correct maximum
sizes of the operations. Return -E2BIG if this size is not supported
because it is too big.
Also this patch causes an uninitialized variable warning so it
initializes ret (although not necessary).
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add functions to access the maximum size we can read/write using
regmap_raw_read/write().
This helps drivers that need to know how much they can write with the
raw functions without problems. There are some devices (e.g. bmc150)
that have fifos as registers which need to be read in specific chunks
otherwise samples are dropped.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are some buses which have a limit on the maximum number of bytes
that can be send/received. An example for this is
I2C_FUNC_SMBUS_I2C_BLOCK which does not support any reads/writes of more
than 32 bytes. The regmap_bulk operations should still be able to
utilize the full 32 bytes in this case.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no multi_write support available if we cannot use raw_write.
This is the case if bus->write is not implemented.
This patch adds a condition that we need bus and bus->write so that
can_multi_write is true.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
use_single_rw currently reflects the capabilities of the connected
device. The capabilities of the bus are currently missing for this
variable.
As there are read only and write only buses we need seperate values for
use_single_rw to also reflect tha capabilities of the bus.
This patch splits use_single_rw into use_single_read and
use_single_write. The initialization is changed to check the
configuration for use_single_rw and to check the capabilities of the
used bus.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regmap config does not prohibit val_bytes that are not powers of
two. But the current code of regmap_bulk_write for use_single_rw does
limit the possible val_bytes to 1, 2 and 4.
This patch fixes the behaviour to allow bus writes with non-standard
val_bytes sizes.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return -ENOTSUPP if map->bus->read is not implemented and we do not use
the cache. This code path would directly use bus->read would run into an
NULL pointer for the read function.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This function is missing a check if map->bus->write is implemented. If
it is not implemented arbitrary raw writes are not possible.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are two typos in drivers/base/regmap/regmap.c, and they may
introduce some noise when checking new patches.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These values are defined as unsigned int in the struct and are assigned
to int values.
This patch fixes the type to be unsigned int instead.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Init functions defined in regmap*.c files are now prefixed with
__, take lockdep key and class parameters, and should not be
called directly: move the documentation to regmap.h, where the
macros are defined.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lockdep validator complains about recursive locking and deadlock
when two different regmap instances are called in a nested order.
That happens anytime a regmap read/write call needs to access
another regmap.
This is because, for performance reason, lockdep groups all locks
initialized by the same mutex_init() in the same lock class.
Therefore all regmap mutexes are in the same lock class, leading
to lockdep "nested locking" warnings if a regmap accesses another
regmap.
In general, it is impossible to establish in advance the hierarchy
of regmaps, so we make sure that each regmap init call initializes
its own static lock_class_key. This is done by wrapping all
regmap_init calls into macros.
This also allows us to give meaningful names to the lock_class_key.
For example, in rt5677 case, we have in /proc/lockdep_chains:
irq_context: 0
[ffffffc0018d2198] &dev->mutex
[ffffffc0018d2198] &dev->mutex
[ffffffc001bd7f60] rt5677:5104:(&rt5677_regmap)->_lock
[ffffffc001bd7f58] rt5677:5096:(&rt5677_regmap_physical)->_lock
[ffffffc001b95448] &(&base->lock)->rlock
The above would have resulted in a lockdep recursive warning
previously. This is not the case anymore as the lockdep validator
now clearly identifies the 2 regmaps as separate.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
IS_ENABLED should only be used for CONFIG_* symbols.
I have done a small test:
#define REGMAP_ALLOW_WRITE_DEBUGFS
IS_ENABLED(REGMAP_ALLOW_WRITE_DEBUGFS) returns 0.
#define REGMAP_ALLOW_WRITE_DEBUGFS 0
IS_ENABLED(REGMAP_ALLOW_WRITE_DEBUGFS) returns 0.
#define REGMAP_ALLOW_WRITE_DEBUGFS 1
IS_ENABLED(REGMAP_ALLOW_WRITE_DEBUGFS) returns 1.
#define REGMAP_ALLOW_WRITE_DEBUGFS 2
IS_ENABLED(REGMAP_ALLOW_WRITE_DEBUGFS) returns 0.
So fix the misuse of IS_ENABLED(REGMAP_ALLOW_WRITE_DEBUGFS) and switch to
use #if defined(REGMAP_ALLOW_WRITE_DEBUGFS) instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When inserting a new register into a block, the present bit map size is
increased using krealloc. krealloc does not clear the additionally
allocated memory, leaving it filled with random values. Result is that
some registers are considered cached even though this is not the case.
Fix the problem by clearing the additionally allocated memory. Also, if
the bitmap size does not increase, do not reallocate the bitmap at all
to reduce overhead.
Fixes: 3f4ff561bc ("regmap: rbtree: Make cache_present bitmap per node")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Allow the user to write the cache_only and cache_bypass settings.
This can be useful for debugging.
Since this can lead to the hardware getting out-of-sync with the
cache, at least for the period that the cache state is forced, the
kernel is tainted and the action is recorded in the kernel log.
When disabling cache_only through debugfs a cache sync will be performed.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add an optional delay_us field in reg_sequence to allow the client to
specify a delay (in microseconds) to be applied after any given write
in a sequence of writes.
We treat a delay in a sequence the same way we treat a page change as
they are logically similar in that you can coalesce all write before
a delay (in the same way you can coalesce all writes before a page
change is needed)
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Separate the functionality using sequences of register writes from the
functions that take register defaults. This change renames the arguments
in order to support the extension of reg_sequence to take an optional
delay to be applied after any given register in a sequence is written.
This avoids adding an int to all register defaults, which could
substantially increase memory usage for regmaps with large default tables.
This also updates all the clients of multi_reg_write/register_patch.
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Zero length reads make no sense in a regmap context and are likely to
trigger bugs further down the stack so insert an error check, also
silencing compiler warnings about use of ret in cases where we iterate
per register.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently regmap requires that a reg_read callback is supplied, otherwise a
warning is emitted each time regmap_read() is called. This means a device
or bus without readback support needs to supply dummy reg_read callback.
Apart from that regmap_read() will still work fine if a cache is used.
Remove the warning and let regmap_readable() return false if not reg_read
callback is supplied. This means a device no longer has to supply a dummy
callback if it does not support readback and it also doesn't have to have a
readable_reg callback that always returns false since this is now implicit.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap_fields_force_write() is similar to regmap_fields_write(),
but regmap_fields_force_write() write data to register even though
it is same value.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap_write_bits() is similar to regmap_update_bits(),
but regmap_write_bits() write data to register even though
it is same value.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sometimes we want to write data even though it doesn't change value.
Then, force_write option on _regmap_update_bits() helps this purpose.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The way the mask is generated in regmap_field_init() is wrong.
Indeed, a field initialized with msb = 31 and lsb = 0 provokes a shift
overflow while calculating the mask field.
On some 32 bits architectures, such as x86, the generated mask is 0,
instead of the expected 0xffffffff.
This patch uses GENMASK() to fix the problem, as this macro is already safe
regarding shift overflow.
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In big endian mode regmap_bulk_read gives incorrect data
for byte reads.
This is because memcpy of a single byte from an address
after full word read gives different results when
endianness differs. ie. we get little-end in LE and big-end in BE.
Signed-off-by: Arun Chandran <achandran@mvista.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
set_irq_flags is ARM specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in
.map() functions and we can simply remove the set_irq_flags calls. Some
users also set IRQ_NOPROBE and this has been maintained although it is not
clear that is really needed. There appears to be a great deal of blind
copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Delete jump to a label on the next line, when that label is not
used elsewhere.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier l;
@@
-if (...) goto l;
-l:
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch introduces regmap_get_reg_stride() function which would
be used by the infrastructures like nvmem framework built on top of
regmap. Mostly this function would be used for sanity checks on inputs
within such infrastructure.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch introduces regmap_get_max_register() function which would be
used by the infrastructures like nvmem framework built on top of
regmap.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Existing regmap users call regcache_mark_dirty() as part of the
suspend/resume sequence, to tell regcache that non-default values need to
be resynced post-resume. Add an internal "no_sync_defaults" regmap flag
to remember this state, so that regcache_sync() can differentiate between
these two cases:
1) HW was reset, so any cache values that match map->reg_defaults can be
safely skipped. On some chips there are a lot of registers in the
reg_defaults list, so this optimization speeds things up quite a bit.
2) HW was not reset (maybe it was just clock-gated), so if we cached
any writes, they should be sent to the hardware regardless of whether
they match the HW default. Currently this will write out all values in
the regcache, since we don't maintain per-register dirty bits.
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We're going to add another "does this register need syncing?" check, so
rather than repeating it in three places, we'll separate all of the
relevant logic into a helper function.
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Just one patch for regmap this time around, a change from Steven Rostedt
to prettify the way we're making the regmap internal header available to
the trace events (it turns out that the trace subsystem doesn't actually
need to be in trace/events).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVK6+IAAoJECTWi3JdVIfQ+LoH/jIF6jq8oFna+T7uBa0cMw3p
vLm8N+j4ONLTVuEX0pd4+n13st2P4Epj6fVKJHFCPED/omdBMNWpGTn0ewX7AKCx
7jgjURmhv/WXWfLUzmlBHtM3Z4A/G2gEU1JFXFvCkbzsJwiqxjhElGuUoI+NWxyP
pW0nOABgPbIfhd0/MKvtNiBd63EXNEQilDrBPepp8UlhBR2DXQL9xdNBB4kbMMSk
5gjDmTIig16ORODvxgb9kK1DCaRQ265p3sa0O0fNJxfjpLmmXqBX3PXWNeCmOD4D
OMWh0QbhipdUO+VKMBRaWYxnIfAJnY9z408W9LgjhHcBLDsfiI+RPhCHG9+qatE=
=TkKs
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap update from Mark Brown:
"Just one patch for regmap this time around, a change from Steven
Rostedt to prettify the way we're making the regmap internal header
available to the trace events (it turns out that the trace subsystem
doesn't actually need to be in trace/events)"
* tag 'regmap-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Move tracing header into drivers/base/regmap
This patch fixes a bad interaction between the support that was added
for having regmaps without devices for early system controller
initialization and the trace support. There's a very good analysis of
the actual issue in the commit message for the change.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVEGNEAAoJECTWi3JdVIfQO+oH/1E2Ho6+X0lIG1mAIC27fae+
XwxtVvUOjCMSPOJ2gg+++YSKc7KIgkxt/VHpw2VllgklYDz32hHloaX/NCfIFaAt
jqTcE+PEeNJgjiZ0qa9zidMeT+BakhsYYl1gwA+0NYVH6AQuwXhhlKdq5+0MmySB
QMCVmWcB/XdvIW5t1nGleahTxqaIRyFXGk1q4dArKjlWSolKrLJr1QHXVvgJBDWN
BTVuzI5WCzzCc1W4FHO6X91PQCEdc7eJxrCXGIuZ53nZlLx3YbhdKxHifibaxU4e
7pRFH1e5FI2jEYjcfDsYi71A+OuexXGHmq1Trm2uPaSIFsCTz32QzieyTD2Lfp8=
=eX90
-----END PGP SIGNATURE-----
Merge tag 'regmap-fix-v4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fix from Mark Brown:
"This patch fixes a bad interaction between the support that was added
for having regmaps without devices for early system controller
initialization and the trace support.
There's a very good analysis of the actual issue in the commit message
for the change"
* tag 'regmap-fix-v4.0-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: introduce regmap_name to fix syscon regmap trace events
The tracing events for regmap are confined to the regmap subsystem. It
also requires accessing an internal header. Instead of including the
internal header from a generic file location, move the tracing file
into the regmap directory.
Also rename the regmap tracing header to trace.h, as it is redundant to
keep the regmap.h name when it is in the regmap directory.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When inserting a new register into a block at the lower end the present
bitmap is currently shifted into the wrong direction. The effect of this is
that the bitmap becomes corrupted and registers which are present might be
reported as not present and vice versa.
Fix this by shifting left rather than right.
Fixes: 472fdec7380c("regmap: rbtree: Reduce number of nodes, take 2")
Reported-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
regcache_sync() spews warnings when a value was cached for a read-only
register as it tries to write all registers no matter whether they are
writable or not. This patch adds regmap_wrtieable() checks for
avoiding it in regcache_sync_block_single() and regcache_block_raw().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
The %irq_flags flag is used to request the threaded IRQ and is also a
parameter of the caller. Hence, we cannot be sure that IRQF_ONESHOT is
set. This change avoids the potentially missing flag by setting
IRQF_ONESHOT when requesting the threaded IRQ.
Generated by: scripts/coccinelle/misc/irqf_oneshot.cocci
Signed-off-by: Valentin Rothberg <Valentin.Rothberg@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
SMBus access functions assume that 16-bit values are formatted as
little endian numbers. The direct i2c access functions in regmap,
however, assume that 16-bit values are formatted as big endian numbers.
As a result, the current code returns different values if an i2c chip's
16-bit registers are accessed through i2c access functions vs. SMBus
access functions.
Use regmap_smbus_read_word_swapped and regmap_smbus_write_word_swapped
for 16-bit SMBus accesses if a chip is configured as REGMAP_ENDIAN_BIG.
If the chip is configured as REGMAP_ENDIAN_LITTLE, keep using
regmap_smbus_write_word_data and regmap_smbus_read_word_data. Otherwise
reject registration if the controller does not support direct i2c accesses.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
We'll need to call it from regmap-i2c.c, which can be built as module.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch move struct regmap.spinlock_flags into the union of
spinlock, so that we can shrink struct regmap size.
Signed-off-by: Yalin Wang <yalin.wang@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the recently added support for bus operations to provide a standard
mapping for AC'97 register I/O.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
If the inlcude headers aren't sorted alphabetically, then the
logical choice is to append new ones, however that creates a
lot of potential for conflicts or duplicates because every change
will then add new includes in the same location.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When all the registers are volatile(unlikely, but logically and mostly
will happen for some 'device' who has very few registers), then the
count will be euqal to 0, then kmalloc() will return ZERO_SIZE_PTR,
which equals to ((void *)16).
So this patch fix this with just doing the zero check before calling
kmalloc(). If the count == 0, so we can make sure that all the registers
are volatile, so no cache is need.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes checkpatch.pl warning for regmap cache.
WARNING : prefer kmalloc_array over kmalloc with multiply
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This may speed regcache_hw_init() up for some cases that there
has volatile registers.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The macro "REGMAP_ALLOW_WRITE_DEBUGFS" can be used to enable write
support on the registers file in the debugfs. The mode of the file is
fixed to 0400 so it is not possible to write the file ever.
This patch fixes the mode by setting it to the correct value depending
on the macro.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we cannot make sure the 'val_count' will always be none zero
here, and then if it equals to zero, the kmemdup() will return
ZERO_SIZE_PTR, which equals to ((void *)16).
So this patch fix this with just doing the zero check before calling
kmemdup().
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
If 'map->dev' is NULL and there will lead dev_name() to be NULL pointer
dereference. So before dev_name(), we need to have check of the map->dev
pionter.
We also should make sure that the 'name' pointer shouldn't be NULL for
debugfs_create_dir(). So here using one default "dummy" debugfs name when
the 'name' pointer and 'map->dev' are both NULL.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
If LOG_DEVICE is defined and map->dev is NULL it will lead to NULL
pointer dereference. This patch fixes this issue by adding check for
dev->NULL in all such places in regmap.c
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Recents commits for getting reg endianness causing NULL pointer
dereference if dev is passed NULL in regmap_init_mmio. This patch
fixes this issue, and allows to parse reg endianness only if dev
and dev->of_node exist.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Call stack of regcache_sync calls may not emit any error message even if
operation was cancelled due an error in I/O driver. One such a silent error
is for instance if I2C bus driver doesn't receive ACK from the I2C device
and returns -EREMOTEIO.
Since many users of regcache_sync() don't check and print the error there is
no any indication that HW registers are potentially out of sync.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Ensure that the mode reported for the registers file in debugfs is
accurate by marking it as read only when the define to enable writes has
not been set. This is on the edge of being a bug fix but it's debugfs
and it makes it much easier for users to spot what's going wrong when
they forget to enable writeability.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUF218AAoJECTWi3JdVIfQDToIAIPpC20A0Tb2+20pxUDO717d
QOpLymMm9qe4Fwbb8wdzM/D3Usy4CG0vrZg8cFX2qZnfKrMPQy9/IQ6kh0SWMvpb
5FQRBd8IkEIMxM9Ng+aAarJIS+xQTdgLDjFIapaBNp0DW5eT0ZaEMYri5Wt2Ut4u
a33GtvXC8Raqbk6A7GpxijVKuApFVz+SH8HB/NqOyNZWXiXcRkZ6bWwgn7YeAqPy
ABg+CAQhjwzXjZSn8Vbt6TNS7jhJzXx5v1wEsx4mcthj2GlBlFexvYDqYBM8VuGJ
GO4F1EHCK/bVRGAgfy1EyeYPqEuedJleap5r8/0T6oFi4VDJ2z6funnt8QwwVDo=
=NVI6
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fix from Mark Brown:
"Fix registers file in debugfs
Ensure that the mode reported for the registers file in debugfs is
accurate by marking it as read only when the define to enable writes
has not been set. This is on the edge of being a bug fix but it's
debugfs and it makes it much easier for users to spot what's going
wrong when they forget to enable writeability"
* tag 'regmap-v3.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Fix debugfs-file 'registers' mode
this patch change struct regmap->mutex and struct regmap->spinlock
as an union, because these 2 members are only used one of them,
we change it to shrink the struct size.
Signed-off-by: Yalin Wang <yalin.wang@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The macro "REGMAP_ALLOW_WRITE_DEBUGFS" can be used to enable write
support on the registers file in the debugfs. The mode of the file is
fixed to 0400 so it is not possible to write the file ever.
This patch fixes the mode by setting it to the correct value depending
on the macro.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the device can't support block writes then don't attempt to use raw
syncing which will automatically generate block writes for adjacent
registers, use the existing _single() block syncing implementation.
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Split regmap_get_endian() in two functions, regmap_get_reg_endian() and
regmap_get_val_endian().
This allows to:
- Get rid of the three switch()es on "type", incl. error handling in
three "default" cases,
- Get rid of the regmap_endian_type enum,
- Get rid of the non-NULL check of "config" (regmap_init() already
checks for that),
- Get rid of the "endian" output parameters, and just return the
regmap_endian enum value, as the functions can no longer fail.
This saves 21 lines of code (despite the still-present
one-comment-per-line over-documentation), and 30 bytes of code on ARM
V7.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
A previous over-zealous factorisation of code means that we only treat
registers as volatile if they are readable. For most devices this is fine
since normally most registers can be read and volatility implies
readability but for format_write() devices where there is no readback from
the hardware and we use volatility to mean simply uncacheability this means
that we end up treating all registers as cacheble.
A bigger refactoring of the code to clarify this is in order but as a fix
make a minimal change and only check readability when checking volatility
if there is no format_write() operation defined for the device.
Signed-off-by: Mark Brown <broonie@linaro.org>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: stable@vger.kernel.org
Commit 6cfec04bcc ("regmap: Separate regmap dev initialization") moved the
regmap debugfs initialization after regcache initialization. This means
that the regmap debugfs directory is not created yet when the cache
initialization runs and so any debugfs files registered by the regcache are
created in the debugfs root directory rather than the debugfs directory of
the regmap instance. Fix this by adding a separate callback for the
regcache debugfs initialization which will be called after the parent
debugfs entry has been created.
Fixes: 6cfec04bcc (regmap: Separate regmap dev initialization)
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Commit d647c19951 ("regmap: add DT endianness binding support") had
some issues. Commit ba1b53feb8 ("regmap: Fix DT endianess parsing
logic") fixed the main problem. This patch fixes the other.
Specifically, restore the overall default of REGMAP_ENDIAN_BIG if none of
the config, DT, or the bus specify any endianness. Without this,
of_regmap_get_endian() could return REGMAP_ENDIAN_DEFAULT, which the
calling code can't handle. Since all busses do specify an endianness in
the current code, this makes no difference right now, but I saw no
justification in the patch description for removing this final default.
Also, clean up the code a bit:
* s/of_regmap_get_endian/regmap_get_endian/ since the function isn't DT-
specific, even if the reason it was originally added was to add some
DT-specific features.
* After potentially reading an endianess specification from DT, the code
checks whether DT did specify an endianness, and if so, returns it. Move
this test outside the whole switch statement so that if the
REGMAP_ENDIAN_REG case ever modifies *endian, this check will pick that
up. This partially reverts part of commit ba1b53feb8 ("regmap: Fix DT
endianess parsing logic"), while maintaining the bug-fix that commit
made to this code.
* Make the comments briefer, and only refer to the specific action taken
at their location. This makes most of the comments independent of DT,
and easier to follow.
Cc: Xiubo Li <Li.Xiubo@freescale.com>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Cc: Thierry Reding <treding@nvidia.com>
Fixes: d647c19951 ("regmap: add DT endianness binding support")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit d647c19951 ("regmap: add DT endianness binding support.")
added support to parse the device endianness from the device tree
but unfortunately the added logic doesn't have the same semantics
than the old code. This leads to a NULL dereference pointer error
when these properties are not provided by the Device Tree:
Unable to handle kernel NULL pointer dereference at virtual address 00000044
pgd = c0004000
[00000044] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 5 PID: 1 Comm: swapper/0 Not tainted 3.17.0-rc1-next-20140818ccu #671
task: ea412800 ti: ea484000 task.ti: ea484000
PC is at regmap_update_bits+0xc/0x5c
The problem is that platforms that rely on the default value now
gets different values due two related issues in the current code:
a) It only parses the endianness from DT for the regmap registers
and not for the regmap values but it checks unconditionally in
both cases if the resulting endiannes is REGMAP_ENDIAN_NATIVE.
b) REGMAP_ENDIAN_NATIVE is not even a valid DT property according
to the regmap DT binding documentation so it shouldn't be set.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add explicit dependencies for the various regmap modules, so Kconfig
will print a warning message when another module selects a regmap module
without fulfilling its dependencies.
Without this, it's much more difficult to find out which module did the
offending select.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
For many drivers which will support rich endianness of Devices
need define DT properties by itself with the binding support.
The endianness using regmap:
Index Device Properties if needs bytes-swap,
or just ignore it
-------------------------------------------------------------
1 BE 'big-endian'
2 LE 'little-endian'
The properties include all the register values and the buffers.
And these properties are very usful for the MMIO devices:
Such as: a memory-mapped device, on one SoC is in BE mode, while
in another SoC will be in LE mode, and the CPU will always in LE
mode.
For the first case, we must use cpu_to_be32/be32_to_cpu for
32-bit registers accessing, so the 'big-endian' property is needed.
For the second case, we can just ignore the bytes-swap
functions like cpu_to_le32/le32_to_cpu, so the 'little-endian'
property could be abscent.
And vice versa...
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a new function regmap_get_device to obtain the underlying struct
device from a regmap.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 932580409a
"regmap: mmio: Add support for 1/2/8 bytes wide register address."
broke regmap_mmio_write for uneven counts, for example 32-bit register
addresses with no padding and 8-byte values (count = 5).
Fix this by allowing all counts large enough to include some value.
This check was BUG_ON(count < 4) before the last change.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since we cannot make sure the 'chip->num_regs' will always be none zero
from the users, and then if 'chip->num_regs' equals to zero by mistake
or other reasons, the kzalloc() will return ZERO_SIZE_PTR, which equals
to ((void *)16).
So this patch fix this with just checking the 'chip->num_regs' before
calling kzalloc().
This also sorts the header files in alphabetical order at the same time.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
drivers/base/regmap/regmap.c: In function ‘_regmap_range_multi_paged_reg_write’:
drivers/base/regmap/regmap.c:1665: warning: ‘this_page’ may be used uninitialized in this function
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since we cannot make sure the 'len = pair_size * num_regs' will always
be none zero from the users, and then if 'num_regs' equals to zero by
mistake or other reasons, the kzalloc() will return ZERO_SIZE_PTR, which
equals to ((void *)16).
So this patch fix this with just doing the 'len' zero check before calling
kzalloc().
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some I2C adapters are only compatible with the SMBus protocol and do not
support standard I2C transfers.
Fallback to SMBus transfers if we encounter such kind of adapters.
The transfer type is chosen according to the val_bits field in the regmap
config.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some busses do not support sending/receiving multiple registers in one go.
Such kind of busses just unpack the registers that have been previously
packed by the regmap core or pack registers that will be later unpacked by
the core code.
Add reg_write and reg_read callbacks in order to optimize access through
this kind of busses.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Change regcache_rbtree_node strcuture fields order to align the pointers on
64bits architectures.
Signed-off-by: Jean-Christophe PINCE <jean-christophe.pince@intel.com>
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
'offset = *(u32 *)reg;'
This will be okey for 32/64-bits register device, but for 8/16-bits
register ones, the 'offset' value will overflow, for example:
The IMX2 Watchdog, whose registers and values are all 16-bits:
If the IO base virtual address is ctx->regs = 0x888c0000, and the now
doing the 0x00 register accessing:
Using 'offset = *(u32 *)reg' the offset value will possiblly be 0x77310000,
Using 'offset = *(u16 *)reg' the offset value will be 0x0000.
In the regmap_mmio_gather_write(), ctx->regs + 0x7731000 will be 0xffbd0000,
but actually it should be ctx->regs + 0x0000 = 0x888c0000.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Allow busses to request little endianness formatting and
parsing for 16- and 32-bit values. This will be useful to
support regmap-mmio.
For the following the scenarios using the regmap-mmio,
for example:
Index CPU Device Endianess flag for values
----------------------------------------------------------
1 LE LE REGMAP_ENDIAN_DEFAULT/NATIVE
2 LE BE REGMAP_ENDIAN_BIG
3 BE BE REGMAP_ENDIAN_DEFAULT/NATIVE
4 BE LE REGMAP_ENDIAN_LITTLE
For one device driver, which will support all the cases above,
needs two boolean properties in DT node like: 'big-endian'
for case 2 and 'little-endian' for case 4, and for cases 1
and 3 they all will be absent.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add mising braces so that the nodev mode actually works (which was a bit
of an oversight).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTR73jAAoJELSic+t+oim9DU4P/0syjNA3/oiZ+HgJZpCELafI
sbbAV+nKTzOKpYTtGLxpQe67gPrZ5kVw9wydYOhWRZ22wbdJ3dyBcizpGnpPQuEC
1/MK8GYj9F1bO3FimwRhdu3oyafNRYVAfNZvBzxrqhcq8US5xu3CLMUFOVHreVOi
+IZn8hrsE9Z6lf/MAJUhsPDvXcqnQAHTODqzIKB38zpwdy22NOfDJgoDRIhKIoun
xIdvf1pmMvKNc8ClZzBHokMgg37UbsVYPeUP6zH7d0+0Id38v2R94MKFC+uAcgk0
xj4R9c2biVs8+Vz9TG2eMeVbBU6XlYVkHFrXUKFfpua4aOuLf17wun52Gt8JdBi9
c4HFzvJXbvvbWk+b24P6+olh0yVmD+2wrsjpEa/nkB3aZMLqrIPX7gCo/3z8TvS7
iDf6snJiUPOK5OIYJSm28ERrkTjxvXTpFZFwvss7vNZ08Oz4FgCb+UmRAdyXKaec
slmLqVLDYV2+VrAqHZe5QFjWc2IJ1bqTX7R57Z6REx+s+e+A6K8i9TDzsQ7zLa+d
+M2oq7Wn3bwXQwwuOvbg0ZrE96PyFbyXqcS5xcByFv24MoX6T9MXlFNhAPXxq+NB
j854BZbo8OjL3uR91CXsR0a6/UERamnENQdiw3GTEVxjovGRfvRjdsfBjpPXBf3U
YzFEflwQIU/CqdtELDWQ
=Kfpr
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.15-nodev' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fix from Mark Brown:
"regmap: Fix for nodev mode
Add mising braces so that the nodev mode actually works (which was a
bit of an oversight)"
Testing schmesting. We don't need not steenking testing. We have
deadlines to beat, and new code to write.
* tag 'regmap-v3.15-nodev' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: adds missing braces in regmap_init()
Here's the big driver core / sysfs update for 3.15-rc1.
Lots of kernfs updates to make it useful for other subsystems, and a few
other tiny driver core patches.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7A0wACgkQMUfUDdst+ynJNACfZlY+KNKIhNFt1OOW8rQfSZzy
1PYAnjYuOoly01JlPrpJD5b4TdxaAq71
=GVUg
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and sysfs updates from Greg KH:
"Here's the big driver core / sysfs update for 3.15-rc1.
Lots of kernfs updates to make it useful for other subsystems, and a
few other tiny driver core patches.
All have been in linux-next for a while"
* tag 'driver-core-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (42 commits)
Revert "sysfs, driver-core: remove unused {sysfs|device}_schedule_callback_owner()"
kernfs: cache atomic_write_len in kernfs_open_file
numa: fix NULL pointer access and memory leak in unregister_one_node()
Revert "driver core: synchronize device shutdown"
kernfs: fix off by one error.
kernfs: remove duplicate dir.c at the top dir
x86: align x86 arch with generic CPU modalias handling
cpu: add generic support for CPU feature based module autoloading
sysfs: create bin_attributes under the requested group
driver core: unexport static function create_syslog_header
firmware: use power efficient workqueue for unloading and aborting fw load
firmware: give a protection when map page failed
firmware: google memconsole driver fixes
firmware: fix google/gsmi duplicate efivars_sysfs_init()
drivers/base: delete non-required instances of include <linux/init.h>
kernfs: fix kernfs_node_from_dentry()
ACPI / platform: drop redundant ACPI_HANDLE check
kernfs: fix hash calculation in kernfs_rename_ns()
kernfs: add CONFIG_KERNFS
sysfs, kobject: add sysfs wrapper for kernfs_enable_ns()
...
Here's the big char/misc driver updates for 3.15-rc1.
Lots of various things here, including the new mcb driver subsystem.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7ArIACgkQMUfUDdst+ylS+gCfcJr0Zo2v5aWnqD7rFtFETmFI
LhcAoNTQ4cvlVdxnI0driWCWFYxLj6at
=aj+L
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg KH:
"Here's the big char/misc driver updates for 3.15-rc1.
Lots of various things here, including the new mcb driver subsystem.
All of these have been in linux-next for a while"
* tag 'char-misc-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (118 commits)
extcon: Move OF helper function to extcon core and change function name
extcon: of: Remove unnecessary function call by using the name of device_node
extcon: gpio: Use SIMPLE_DEV_PM_OPS macro
extcon: palmas: Use SIMPLE_DEV_PM_OPS macro
mei: don't use deprecated DEFINE_PCI_DEVICE_TABLE macro
mei: amthif: fix checkpatch error
mei: client.h fix checkpatch errors
mei: use cl_dbg where appropriate
mei: fix Unnecessary space after function pointer name
mei: report consistently copy_from/to_user failures
mei: drop pr_fmt macros
mei: make me hw headers private to me hw.
mei: fix memory leak of pending write cb objects
mei: me: do not reset when less than expected data is received
drivers: mcb: Fix build error discovered by 0-day bot
cs5535-mfgpt: Simplify dependencies
spmi: pm: drop bus-level PM suspend/resume routines
spmi: pmic_arb: make selectable on ARCH_QCOM
Drivers: hv: vmbus: Increase the limit on the number of pfns we can handle
pch_phub: Report error writing MAC back to user
...
It need to add curly braces because the inner for "if" has
two statements.
coccicheck says:
drivers/base/regmap/regmap.c:765:2-44:
code aligned with following code on line 766
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the support for 1/2/8 bytes wide register address checking.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since regmap core and mmio have already support for 1/2/8 bytes wide values,
so adds support for 1/2/8 bytes wide registers address.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the regcache_default_sync, if a register isn't writeable, then
_regmap_write will return an error and the rest of the sync will be
aborted. Avoid this by checking if a register is writeable before
trying to sync it.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The default sync operation was still assuming a stride of one, fix it
to respect the reg_stride set in the map.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
regmap deploys the spinlock for the protection when set up in fast_io
mode. This may lead to sleep-in-atomic by memory allocation with
GFP_KERNEL in regmap_bulk_write(). This patch fixes it by moving the
allocation out of the lock.
[Fix excessively large locked region -- broonie]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
With fast_io we use mutexes to lock the I/O operations so we would need
to do GFP_ATOMIC allocations if we wanted to do allocations inside the
lock as we do currently. Since it is unlikely that we will want to register
a patch outside of init where concurrency shouldn't be an issue move the
allocation of the patch data outside the lock.
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
After setting the 'data' pointer (wchich is returned to the caller for
freeing later) the regmap_add_irq_chip() could still fail for various
reasons (ENOMEM, regmap_read or regmap_write failure). In such case the
memory under 'data' was freed in error path and error value was returned
but the 'data' variable was not changed.
This could lead to errors if the caller passed such 'data' to
regmap_del_irq_chip().
The 'data' pointer should be changed atomically from the caller
perspective - set it only on regmap_add_irq_chip() success.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is the implementation of regmap_multi_reg_write()
There is a new capability 'can_multi_write' that device drivers
must set in order to use this multi reg write mode.
This replaces the first definition, which just defined the API.
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In some cases, we need regmap's format parse_val function
to do be/le translation according to the bus configuration.
For example, snd_soc_bytes_put() uses regmap to write/read values,
and use cpu_to_be() directly to covert MASK into big endian. This
is a defect, and should use regmap's format function to do it according
to bus configuration.
Signed-off-by: Nenghua Cao <nhcao@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since we now have an internal version of regmap_multi_reg_write use this
to apply the register patch.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Devices with more complex boot proceedures may occasionally apply the
register patch manual. regmap_multi_reg_write is a logical way to do so,
however the patch must be applied with cache bypass on, such that it
doesn't override any user settings. This patch adds a
regmap_multi_reg_write_bypassed function that applies a set of writes
with the bypass enabled.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There should be no need for the writes supplied to this function to be
edited by it so mark them as const.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
/drivers/base/regmap/regmap.c:717:6-33: WARNING:
Comparison to bool.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Nenghua Cao <nhcao@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently, we check the registers in the patch are aligned to the
register stride everytime we sync the cache and the first time the patch
is written out is unchecked.
This patch checks the register patch when we first register it so the
first writes are no longer unchecked and then doesn't check on
subsequent syncs as the patch will be unchanged.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since sometimes the 'config' parameter has no use, it should be NULL.
And make the code simplifier.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Create special function regmap_attach_dev
which can be called separately out of regmap_init.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SPMI states that a slave may contain two register spaces, the Base
register space is a 5-bit byte-addressable space accessed via the
Register Read/Write and Register Zero Write command sequences, and the
Extended register space: a 16-bit byte-addressable space accessed via
the Extended Read/Write and Extended Read/Write Long command sequences.
Provide support for accessing both of these spaces, taking advantage of
the more bandwidth-efficient commands ('Register 0 Write' vs 'Register
Write', and 'Extended Register Read/Write' vs 'Extended Register
Read/Write Long') when possible.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
irqdomain now supports removal of domains on exit so we can properly clean
up on deletion of a regmap irqchip.
Signed-off-by: Mark Brown <broonie@linaro.org>
When a map covers a single register, max_register is equal
to 0, so the "registers" & "access" files were not created.
Now they will be, as register 0 must be readable for such
map to make sense.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
regcache_sync_block_raw_flush takes the address of the base register
and the address of one past the last register to write to. "count" is
the number of registers in the range, not the number of bytes, it
should be (end addr - start addr) / stride. Without accounting for
strides greater than one, registers past the end might be synced or
the writeable_reg callback at the beginning of _regmap_raw_write will
fail and nothing will be written.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
regmap_bulk_write() should decay to performing individual writes
if we're using a "no-bus" regmap. Unfortunately, it returns an
error because there is no map->bus pointer. Fix it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSrhGrAAoJEHm+PkMAQRiGsNoH/jIK3CsQ2lbW7yRLXmfgtbzz
i2Kep6D4SDvmaLpLYOVC8xNYTiE8jtTbSXHomwP5wMZ63MQDhBfnEWsEWqeZ9+D9
3Q46p0QWuoBgYu2VGkoxTfygkT6hhSpwWIi3SeImbY4fg57OHiUil/+YGhORM4Qc
K4549OCTY3sIrgmWL77gzqjRUo+pQ4C73NKqZ3+5nlOmYBZC1yugk8mFwEpQkwhK
4NRNU760Fo+XIht/bINqRiPMddzC15p0mxvJy3cDW8bZa1tFSS9SB7AQUULBbcHL
+2dFlFOEb5SV1sNiNPrJ0W+h2qUh2e7kPB0F8epaBppgbwVdyQoC2u4uuLV2ZN0=
=lI2r
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc4' into regmap-core
Needed as a subsequent patch is built on some of the fixes.
Linux 3.13-rc4
regmap_bulk_read() should decay to performing individual reads if
we're using a "no-bus" regmap. Unfortunately, it returns an
error because there is no map->bus pointer. Fix it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
In some cases, clear interrupt register may be at address 0.
This patch allows to use such configurations by adding additional
configuration bit to indicate this.
[With doc fix from Levente Kurusa <levex@linux.com> -- broonie]
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
clk_get() returns an error pointer, or a valid token to pass back to the
clock API. Hence, the result must be checked with IS_ERR(), not by
comparison against NULL.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch give a warning when calling regmap_register_patch with
parameter num_regs <= 0.
When the num_regs parameter is zero and krealloc doesn't fail,
then the code would return an uninitialized value. However,
calling this function with num_regs == 0, would be a waste as it
essentially does nothing.
Signed-off-by: Cai Zhiyong <caizhiyong@huawei.com>
Reviewed-by: Geyslan G. Bem <geyslan@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
fix a trivial copy'n'paste error in the regmap kerneldoc, s/write/read/
for the regmap_read(), regmap_raw_read() and regmap_bulk_read() routines
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add basic support for the System Power Management Interface (SPMI) bus.
This is a simple implementation which only implements register accesses
via the Extended Register Read/Write Long commands.
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
If called early enough, regmap_debugfs_init causes a crash, if the
fs subsystem does not have its mount cache created yet. Even if this
would work, the root node for the regmap debugfs is still missing,
thus postpone the regmap_debugfs_init in this case until the root
node is created. A special regmap_debugfs_early list is created for
this purpose which is parsed later in the boot.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
clear the status bit if the mask register doesn't prevent
the chip level irq from being asserted
OR in the following sequence, there will be irq storm happens:
1) interrupt is triggered;
2) another thread disables it(the mask bit is set);
3) _Then_ the interrupt thread is not ACKed(the status bit is not cleared),
and it's ignored;
4) if the irq is still asserted because of the uncleared status bit,
the irq storm happens;
Signed-off-by: Yi Zhang <yizhang@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Extend the interface for async I/O by allowing the value buffer to be
omitted and sending the value as part of the register buffer, minimising
the number of separate hardware operations required.
Signed-off-by: Mark Brown <broonie@linaro.org>
If the value is zero then assume it has been included in the register data
and don't send anything, minimising the number of interactions with the
hardware.
Signed-off-by: Mark Brown <broonie@linaro.org>
New API regmap_multi_reg_write() is defined that allows a set of reg,val
pairs to be written to a I2C client device as one block transfer from the
point of view of a single I2C master system.
A simple demonstration implementation is included that just splits the
block write request into a sequence of single register writes.
The implementation will be modified later to support those I2C clients
that implement the alternative non-standard MULTIWRITE block write mode
so to achieve a single I2C transfer that will be atomic even in multiple
I2C master systems.
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Try to speed up I/O a little by not synchronising until we are finished
scheduling writes. A brief survey of existing users suggests we have none
that would currently benefit from an async cache sync.
Signed-off-by: Mark Brown <broonie@linaro.org>
When regmap_bulk_write() is called with the map->use_single_rw flag set
an immediate mutex deadlock happens because regmap_raw_write() is called
after obtaining the mutex and regmap_raw_write() itself then tries to
obtain the mutex as well.
It is obvious that no one other than myself tried it with a real device.
I did, but only for the purposes of an experiment and demonstration.
But even if this situation will never ever happen with a real device, it
is a bug and therefore should be fixed.
Signed-off-by: Anthony Olech <anthony.olech.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make it easier for drivers to include single register writes in
asynchronous sequences by providing async versions of the write
and update bits operations. The update bits operations are only
likely to be effective when used with devices that have caches
but this is common enough to be useful.
Signed-off-by: Mark Brown <broonie@linaro.org>
Rather than passing a flag around through the entire call stack store it
in the regmap struct and read it when required. This minimises the
visibility of the feature through the API, minimising the code updates
needed to use it more widely.
Signed-off-by: Mark Brown <broonie@linaro.org>
Since it is quite common for single register raw or async writes to be
generated by rbtree cache syncs or firmware downloads and essentially all
hardware will be faster with only a single transfer optimise this case by
copying single values into the internal scratch buffer before sending.
Signed-off-by: Mark Brown <broonie@linaro.org>
Rather than allocating and deallocating the structures used to manage async
transfers each time we do one keep the structures around as long as the
regmap is around. This should provide a small performance improvement.
Signed-off-by: Mark Brown <broonie@linaro.org>
Current Linux kernel is supporting regmap_field method
and it is very useful feature.
It needs one regmap_filed for one register access.
OTOH, there is multi port device which
has many same registers in the market.
The difference for each register access is
only its address offset.
Current API needs many regmap_field for such device,
but it is not good.
This patch adds new regmap_fileds API which can care
about multi port/offset access via regmap.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current regmap_field is supporting read/write functions.
This patch adds new update_bits function for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlIPcACgkQMUfUDdst+ynUMwCaAnITsxyDXYQ4DqEsz8EcOtMk
718AoLrgnUZs3B+70AT34DVktg4HSThk
=USl9
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem
maintainers"
* tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (119 commits)
firmware loader: fix pending_fw_head list corruption
drivers/base/memory.c: introduce help macro to_memory_block
dynamic debug: line queries failing due to uninitialized local variable
sysfs: sysfs_create_groups returns a value.
debugfs: provide debugfs_create_x64() when disabled
rbd: convert bus code to use bus_groups
firmware: dcdbas: use binary attribute groups
sysfs: add sysfs_create/remove_groups for when SYSFS is not enabled
driver core: add #include <linux/sysfs.h> to core files.
HID: convert bus code to use dev_groups
Input: serio: convert bus code to use drv_groups
Input: gameport: convert bus code to use drv_groups
driver core: firmware: use __ATTR_RW()
driver core: core: use DEVICE_ATTR_RO
driver core: bus: use DRIVER_ATTR_WO()
driver core: create write-only attribute macros for devices and drivers
sysfs: create __ATTR_WO()
driver-core: platform: convert bus code to use dev_groups
workqueue: convert bus code to use dev_groups
MEI: convert bus code to use dev_groups
...
A quiet release for regmap, some cleanups, fixes and:
- Improved node coalescing for rbtree, reducing memory usage and
improving performance during syncs.
- Support for registering multiple register patches.
- A quirk for handling interrupts that need to be clear when masked
in regmap-irq.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=um4f
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"A quiet release for regmap, some cleanups, fixes and:
- Improved node coalescing for rbtree, reducing memory usage and
improving performance during syncs.
- Support for registering multiple register patches.
- A quirk for handling interrupts that need to be clear when masked
in regmap-irq"
* tag 'regmap-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: rbtree: Make cache_present bitmap per node
regmap: rbtree: Reduce number of nodes, take 2
regmap: rbtree: Simplify adjacent node look-up
regmap: debugfs: Fix continued read from registers file
regcache-rbtree: Fix reg_stride != 1
regmap: Allow multiple patches to be registered
regmap: regcache: allow read-only regs to be cached
regmap: fix regcache_reg_present() for empty cache
regmap: core: allow a virtual range to cover its own data window
regmap: irq: document mask/wake_invert flags
regmap: irq: make flags bool and put them in a bitfield
regmap: irq: Allow to acknowledge masked interrupts during initialization
regmap: Provide __acquires/__releases annotations
With devices which have a dense and small register map but placed at a large
offset the global cache_present bitmap imposes a huge memory overhead. Making
the cache_present per rbtree node avoids the issue and easily reduces the memory
footprint by a factor of ten. For devices with a more sparse map or without a
large base register offset the memory usage might increase slightly by a few
bytes, but not significantly. E.g. for a device which has ~50 registers at
offset 0x4000 the memory footprint of the register cache goes down form 2496
bytes to 175 bytes.
Moving the bitmap to a per node basis means that the handling of the bitmap is
now cache implementation specific and can no longer be managed by the core. The
regcache_sync_block() function is extended by a additional parameter so that the
cache implementation can tell the core which registers in the block are set and
which are not. The parameter is optional and if NULL the core assumes that all
registers are set. The rbtree cache also needs to implement its own drop
callback instead of relying on the core to handle this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Support for reducing the number of nodes and memory consumption of the rbtree
cache by allowing for small unused holes in the node's register cache block was
initially added in commit 0c7ed856 ("regmap: Cut down on the average # of nodes
in the rbtree cache"). But the commit had problems and so its effect was
reverted again in commit 4e67fb5 ("regmap: rbtree: Fix overlapping rbnodes.").
This patch brings the feature back of reducing the average number of nodes,
which will speedup node look-up, while at the same time also reducing the memory
usage of the rbtree cache. This patch takes a slightly different approach than
the original patch though. It modifies the adjacent node look-up to not only
consider nodes that are just one to the left or the right of the register but
any node that falls in a certain range around the register. The range is
calculated based on how much memory it would take to allocate a new node
compared to how much memory it takes adding a set of unused registers to an
existing node. E.g. if a node takes up 24 bytes and each register in a block
uses 1 byte the range will be from the register address - 24 to the register
address + 24. If we find a node that falls within this range it is cheaper or as
expensive to add the register to the existing node and have a couple of unused
registers in the node's cache compared to allocating a new node.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
A register which is adjacent to a node will either be left to the first
register or right to the last register. It will not be within the node's range,
so there is no point in checking for each register cached by the node whether
the new register is next to it. It is sufficient to check whether the register
comes before the first register or after the last register of the node.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The regmap_debugfs_get_dump_start() function maps from a file offset to the
register that can be found at that position in the file. This is done using a
look-up table. Commit d6814a7d ("regmap: debugfs: Suppress cache for partial
register files") added a check to bypass the look-up table for partial register
files, since the offsets in that table are only correct for the full register
file. The check incorrectly uses the file offset instead of the register base
address and returns it. This will cause the file offset to be interpreted as a
register address which will result in a incorrect output from the registers file
for all reads except at position 0.
The issue can easily be reproduced by doing small reads the registers file, e.g.
`dd if=registers bs=10 count=5`.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
There are a couple of calculations, which convert between register addresses and
block indices, in regcache_rbtree_sync() and regcache_rbtree_node_alloc() which
assume that reg_stride is 1. This will break the rb cache for configurations
which do not use a reg_stride of 1.
Also rename 'base' in regcache_rbtree_sync() to 'start' to avoid confusion with
'base_reg'.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Avoid overlapping register regions by making the initial blklen of a new
node 1. If a register write occurs to a yet uncached register, that is
lower than but near an existing node's base_reg, a new node is created
and it's blklen is set to an arbitrary value (sizeof(*rbnode)). That may
cause this node to overlap with another node. Those nodes should be merged,
but this merge doesn't happen yet, so this patch at least makes the initial
blklen small enough to avoid hitting the wrong node, which may otherwise
lead to severe breakage.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
It may be useful to register multiple patches with regmap, for example
one that depends on the device revision and one that depends on the system
configuration. Add support for doing this, appending any new patches to
the existing patches.
Signed-off-by: Mark Brown <broonie@linaro.org>
The regmap_writeable() check should not be done in
regcache_write() because this prevents read-only
registers to be cached. After a read on a read-only
register its value will not be stored in the cache
and the next time someone will try to read it the
value will be read from the bus instead of the
cache.
Instead the regmap_writeable() check should be done
in _regmap_write() to prevent callers from writing
to read-only registers.
Signed-off-by: Ionut Nicu <ioan.nicu.ext@nsn.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In the initial case when no reg_defaults values are
provided and no register value was added to the cache
yet, the cache_present bitmap is NULL. If this function
is invoked for any register it should return false
(i.e. the register is not cached) instead of true.
Signed-off-by: Ionut Nicu <ioan.nicu.ext@nsn.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
I see no reason why a virtual range shouldn't be allowed to cover its
own data window if the page selection register is in the same place
on every page.
For chips which use paged access for all of their registers, but only
when connected via I2C, and which can access the whole register space
directly when connected via SPI, this allows to avoid acrobatics with
the register ranges by simply mapping the I2C ranges over the data
window beginning at 0x0, and then using linear access for the SPI
variant.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
regcache_sync_block_raw_flush() expects the address of the register after last
register that needs to be synced as its parameter. But the last call to
regcache_sync_block_raw_flush() in regcache_sync_block_raw() passes the address
of the last register in the block. This effectively always skips over the last
register in a block, even if it needs to be synced. In order to fix it increase
the address by one register.
The issue was introduced in commit 75a5f89 ("regmap: cache: Write consecutive
registers in a single block write").
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The usage of strict_strto*() is not preferred, because
strict_strto*() is obsolete. Thus, kstrto*() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the hardware interrupt mask register does not prevent the chip level
irq from being asserted by the corresponding interrupt status bit, already
set interrupt bits should to be cleared once after masking them during
initialization. Add a flag to let drivers enable this behavior.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following sparse warnings:
drivers/base/regmap/regmap.c:305:13: warning: context imbalance in 'regmap_lock_spinlock' - wrong count at exit
drivers/base/regmap/regmap.c:314:13: warning: context imbalance in 'regmap_unlock_spinlock' - unexpected unlock
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This fixes a crash if something tries to do an asynchronous operation on
busless maps which was introduced during the merge window.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c5Gp
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fix from Mark Brown:
"Fix regmap crash for async operation on busless maps
This fixes a crash if something tries to do an asynchronous operation
on busless maps which was introduced during the merge window"
* tag 'regmap-v3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: cache: bail in regmap_async_complete() for bus-less maps
Commit f8bd822cb ("regmap: cache: Factor out block sync") made
regcache_rbtree_sync() call regmap_async_complete(), which in turn does
not check for map->bus before dereferencing it.
This causes a NULL pointer dereference on bus-less maps.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: stable@vger.kernel.org [v3.10 only]
Signed-off-by: Mark Brown <broonie@linaro.org>
The cache is based on the full register map so confuses things if used
for a partial map.
Reported-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is common to access regmap registers at bit level, using
regmap_update_bits or regmap_read functions, however the end user has to
take care of a mask or shifting. This becomes overhead when such use
cases are high. Having a common function to do this is much convenient
and less error prone.
The idea of regmap_field is simple, regmap_field gives a logical
structure to bits of the regmap register, and the driver can use this
logical entity without the knowledge of the bit positions and masks all
over the code. This way code looks much neat and it need not handle the
masks, shifts every time it access the those entities.
With this new regmap_field_read/write apis the end user can setup a
regmap field using regmap_field_init and use the return regmap_field to
read write the register field without worrying about the masks or
shifts.
Also this apis will be useful for drivers which are based on regmaps,
like some clocks or pinctrls which can work on the regmap_fields
directly without having to worry about bit positions.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently all register maps with a cache need to provide a volatile
callback since the default is to assume all registers are volatile.
This is not sensible if we have a cache so change the default to be
fully cached if a cache is provided.
Signed-off-by: Mark Brown <broonie@linaro.org>
This can be used for cache types for which syncing values one by one is
equally efficient as syncing a range, such as the flat cache.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
A node starting before the minimum register is no reason to reject it,
since its end could be in range. The check for the end already exists
two lines lower, so we can just remove the incorrect check.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
regmap-mmio uses a spinlock with spin_lock() and spin_unlock() for locking.
To be able to use the regmap API from different contexts (atomic vs non-atomic),
without the risk of race conditions, we need to use spin_lock_irqsave() and
spin_lock_irqrestore() instead. A new field, the spinlock_flags field, is added
to regmap struct to store the flags between regmap_{,un}lock_spinlock(). The
spinlock_flags field itself is also protected by the spinlock.
Thanks to Stephen Warren for the suggestion of this particular solution.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The parameter passed to the regmap lock/unlock callbacks needs to be
map->lock_arg, regcache passes just map. This works fine in the case that no
custom locking callbacks are used since in this case map->lock_arg equals map,
but will break when custom locking callbacks are used. The issue was introduced
in commit 0d4529c5("regmap: make lock/unlock functions customizable") and is
fixed by this patch.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The parameter passed to the regmap lock/unlock callbacks needs to be
map->lock_arg, regcache passes just map. This works fine in the case that no
custom locking callbacks are used, since in this case map->lock_arg equals map,
but will break when custom locking callbacks are used. The issue was introduced
in commit 0d4529c5 ("regmap: make lock/unlock functions customizable") and is
fixed by this patch.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regmap_debugfs_get_dump_start should return the offset of the register
it should start reading from, However in the current code at one point
the code does not return correct register offset.
With this patch all the returns from this function takes reg_stride in
to consideration to return correct offset.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A register write to hardware is reasonably unlikely to cause locking
dependency issues, the reason we're tainting is that unexpected changes
in the hardware configuration may confuse drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If range information has been provided then when we allocate a rbnode
within a range allocate the entire range. The goal is to minimise the
number of reallocations done when combining or extending blocks. At
present only readability and yes_ranges are taken into account, this is
expected to cover most cases efficiently.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In preparation for being slightly smarter about how we allocate memory
factor out the node allocation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow drivers to discard parts of the register cache, for example if part
of the hardware has been reset.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
_regmap_raw_write() contains code to call regcache_write() to write
values to the cache. That code calls memcpy() to copy the value data to
the start of the work_buf. However, at least when _regmap_raw_write() is
called from _regmap_bus_raw_write(), the value data is in the work_buf,
and this memcpy() operation may over-write part of that value data,
depending on the value of reg_bytes + pad_bytes. At least when using
reg_bytes==1 and pad_bytes==0, corruption of the value data does occur.
To solve this, remove the memcpy() operation, and modify the subsequent
.parse_val() call to parse the original value buffer directly.
At least in the case of 8-bit register address and 16-bit values, and
writes of single registers at a time, this memcpy-then-parse combination
used to cancel each-other out; for a work-buffer containing xx 89 03,
the memcpy changed it to 89 03 03, and the parse_val changed it back to
89 89 03, thus leaving the value uncorrupted. This appears completely
accidental though. Since commit 8a819ff "regmap: core: Split out in
place value parsing", .parse_val only returns the parsed value, and does
not modify the buffer, and hence does not (accidentally) undo the
corruption caused by memcpy(). This caused bogus values to get written
to HW, thus preventing e.g. audio playback on systems with a WM8903
CODEC. This patch fixes that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This reverts commit bc8ce4 (regmap: don't corrupt work buffer in
_regmap_raw_write()) since it turns out that it can cause issues when
taken in isolation from the other changes in -next that lead to its
discovery. On the basis that nobody noticed the problems for quite some
time without that subsequent work let's drop it from v3.9.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix format specifier in dev_dbg and suppress the following warning
drivers/base/regmap/regcache.c: In function
‘regcache_sync_block_raw_flush’:
drivers/base/regmap/regcache.c:593:2: warning: format ‘%d’ expects
argument of type ‘int’, but argument 4 has type ‘size_t’ [-Wformat]
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
regcache_sync_block_raw is used only in this file. Hence make it static.
Silences the following warning:
drivers/base/regmap/regcache.c:608:5: warning:
symbol 'regcache_sync_block_raw' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When syncing blocks of data using raw writes combine the writes into a
single block write, saving us bus overhead for setup, addressing and
teardown.
Currently the block write is done unconditionally as it is expected that
hardware which has a register format which can support raw writes will
support auto incrementing writes, this decision may need to be revised in
future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
For code clarity after implementing block writes split out the raw and
non-raw I/O sync implementations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
The idea of holding blocks of registers in device format is shared between
at least rbtree and lzo cache formats so split out the loop that does the
sync from the rbtree code so optimisations on it can be reused.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
The idea of maintaining a bitmap of present registers is something that
can usefully be used by other cache types that maintain blocks of cached
registers so move the code out of the rbtree cache and into the generic
regcache code.
Refactor the interface slightly as we go to wrap the set bit and enlarge
bitmap operations (since we never do one without the other) and make it
more robust for reads of uncached registers by bounds checking before we
look at the bitmap.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
This will bring no meaningful benefit by itself, it is done as a separate
commit to aid bisection if there are problems with the following commits
adding support for coalescing adjacent writes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mainly useful internally but exported since this is a public API that's
being checked for.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide a helper to do the size based index into a block of registers and
use it when reading a value.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch aims to bring down the average number of nodes
in the rbtree cache and increase the average number of registers
per node. This should improve general lookup and traversal times.
This is achieved by setting the minimum size of a block within the
rbnode to the size of the rbnode itself. This will essentially
cache possibly non-existent registers so to combat this scenario,
we keep a separate bitmap in memory which keeps track of which register
exists. The memory overhead of this change is likely in the order of
~5-10%, possibly less depending on the register file layout. On my test
system with a bitmap of ~4300 bits and a relatively sparse register
layout, the memory requirements for the entire cache did not increase
(the cutting down of nodes which was about 50% of the original number
compensated the situation).
A second patch that can be built on top of this can look at the
ratio `sizeof(*rbnode) / map->cache_word_size' in order to suitably
adjust the block length of each block.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows the cache to sync values directly to the device when stored
in native format and also allows asynchronous I/O.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
_regmap_raw_write() contains code to call regcache_write() to write
values to the cache. That code calls memcpy() to copy the value data to
the start of the work_buf. However, at least when _regmap_raw_write() is
called from _regmap_bus_raw_write(), the value data is in the work_buf,
and this memcpy() operation may over-write part of that value data,
depending on the value of reg_bytes + pad_bytes. At least when using
reg_bytes==1 and pad_bytes==0, corruption of the value data does occur.
To solve this, remove the memcpy() operation, and modify the subsequent
.parse_val() call to parse the original value buffer directly.
At least in the case of 8-bit register address and 16-bit values, and
writes of single registers at a time, this memcpy-then-parse combination
used to cancel each-other out; for a work-buffer containing xx 89 03,
the memcpy changed it to 89 03 03, and the parse_val changed it back to
89 89 03, thus leaving the value uncorrupted. This appears completely
accidental though. Since commit 8a819ff "regmap: core: Split out in
place value parsing", .parse_val only returns the parsed value, and does
not modify the buffer, and hence does not (accidentally) undo the
corruption caused by memcpy(). This caused bogus values to get written
to HW, thus preventing e.g. audio playback on systems with a WM8903
CODEC. This patch fixes that.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Display the name for the chip rather than just the primary IRQ so it is
clearer what exactly has failed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The last register block, which falls into the specified range, is not handled
correctly. The formula which calculates the number of register which should be
synced is inverse (and off by one). E.g. if all registers in that block should
be synced only one is synced, and if only one should be synced all (but one) are
synced. To calculate the number of registers that need to be synced we need to
subtract the number of the first register in the block from the max register
number and add one. This patch updates the code accordingly.
The issue was introduced in commit ac8d91c ("regmap: Supply ranges to the sync
operations").
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Provide a feel of how much overhead the rbtree cache adds to
the game.
[Slightly reworded output in debugfs -- broonie]
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the rbtree code we are exposing statistics relating to the
number of nodes/registers of the rbtree cache for each of the
devices. Ensure that `map->debugfs' has been initialized before
we attempt to initialize the debugfs entry for the rbtree cache.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
A simple fix to stop us leaking a runtime PM reference in the case where
we fail to enable a device.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=D1mN
-----END PGP SIGNATURE-----
Merge tag 'regmap-v3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap PM fix from Mark Brown:
"A simple fix to stop us leaking a runtime PM reference in the case
where we fail to enable a device."
* tag 'regmap-v3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: irq: call pm_runtime_put in pm_runtime_get_sync failed case
This file lists the register ranges in the register map. The condition
to split the range is based on whether the block is readable or not.
Ensure that we lock the `debugfs_off_cache' list whenever we access
and modify the list. There is a possible race otherwise between the
read() operations of the `registers' file and the `range' file.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't need to use any of the file position information
to calculate the base and max register of each block. Just
use the counter directly.
Set `i = base' at the top to avoid GCC flow analysis bugs. The
value of `i' can never be undefined or 0 in the if (c) { ... }.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently the value parsing operations both return the parsed value and
modify the passed buffer. This precludes their use in places like the cache
code so split out the in place modification into a new parse_inplace()
operation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's more idiomatic to pass the map structure around and this means we
can use other bits of information from the map.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we're updating a value in place it's more work to read the value and
compare the value with what we're about to set than it is to just write
the value into the cache; there are no further operations after writing
in the code even though there's an early return here.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Trace when we start and complete async writes, and when we start and
finish blocking for their completion. This is useful for performance
analysis of the resulting I/O patterns.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Even in failed case of pm_runtime_get_sync, the usage_count
is incremented. In order to keep the usage_count with correct
value and runtime power management to behave correctly, call
pm_runtime_put(_sync) in such case.
Signed-off-by Liu Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Li Fei <fei.li@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
lockdep, but it's a mechanical change.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=tiSY
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module update from Rusty Russell:
"The sweeping change is to make add_taint() explicitly indicate whether
to disable lockdep, but it's a mechanical change."
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
MODSIGN: Add option to not sign modules during modules_install
MODSIGN: Add -s <signature> option to sign-file
MODSIGN: Specify the hash algorithm on sign-file command line
MODSIGN: Simplify Makefile with a Kconfig helper
module: clean up load_module a little more.
modpost: Ignore ARC specific non-alloc sections
module: constify within_module_*
taint: add explicit flag to show whether lock dep is still OK.
module: printk message when module signature fail taints kernel.
Stephen Boyd