* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (96 commits)
apic, x86: Use BIOS settings for IBS and MCE threshold interrupt LVT offsets
apic, x86: Check if EILVT APIC registers are available (AMD only)
x86: ioapic: Call free_irte only if interrupt remapping enabled
arm: Use ARCH_IRQ_INIT_FLAGS
genirq, ARM: Fix boot on ARM platforms
genirq: Fix CONFIG_GENIRQ_NO_DEPRECATED=y build
x86: Switch sparse_irq allocations to GFP_KERNEL
genirq: Switch sparse_irq allocator to GFP_KERNEL
genirq: Make sparse_lock a mutex
x86: lguest: Use new irq allocator
genirq: Remove the now unused sparse irq leftovers
genirq: Sanitize dynamic irq handling
genirq: Remove arch_init_chip_data()
x86: xen: Sanitise sparse_irq handling
x86: Use sane enumeration
x86: uv: Clean up the direct access to irq_desc
x86: Make io_apic.c local functions static
genirq: Remove irq_2_iommu
x86: Speed up the irq_remapped check in hot pathes
intr_remap: Simplify the code further
...
Fix up trivial conflicts in arch/x86/Kconfig
* 'x86-vmware-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, paravirt: Remove alloc_pmd_clone hook, only used by VMI
x86, vmware: Remove deprecated VMI kernel support
Fix up trivial #include conflict in arch/x86/kernel/smpboot.c
* 'x86-bios-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, bios: Make the x86 early memory reservation a kernel option
x86, bios: By default, reserve the low 64K for all BIOSes
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (29 commits)
sched: Export account_system_vtime()
sched: Call tick_check_idle before __irq_enter
sched: Remove irq time from available CPU power
sched: Do not account irq time to current task
x86: Add IRQ_TIME_ACCOUNTING
sched: Add IRQ_TIME_ACCOUNTING, finer accounting of irq time
sched: Add a PF flag for ksoftirqd identification
sched: Consolidate account_system_vtime extern declaration
sched: Fix softirq time accounting
sched: Drop group_capacity to 1 only if local group has extra capacity
sched: Force balancing on newidle balance if local group has capacity
sched: Set group_imb only a task can be pulled from the busiest cpu
sched: Do not consider SCHED_IDLE tasks to be cache hot
sched: Drop all load weight manipulation for RT tasks
sched: Create special class for stop/migrate work
sched: Unindent labels
sched: Comment updates: fix default latency and granularity numbers
tracing/sched: Add sched_pi_setprio tracepoint
sched: Give CPU bound RT tasks preference
sched: Try not to migrate higher priority RT tasks
...
After a period of RFC for this driver, I think it is ready
for inclusion in the platform-driver-x86 tree, hopefully to
be staged in the next merge window into Linus's tree.
--Vernon
------------------------------------------------------------
IBM Real-Time "SMI Free" mode driver
This driver supports the Real-Time Linux (RTL) BIOS feature.
The RTL feature allows non-fatal System Management Interrupts
(SMIs) to be disabled on supported IBM platforms and is
intended to be coupled with a user-space daemon to monitor
the hardware in a way that can be prioritized and scheduled
to better suit the requirements for the system.
The Device is presented as a special "_RTL_" table to the OS
in the Extended BIOS Data Area. There is a simple protocol
for entering and exiting the mode at runtime. This driver
creates a simple sysfs interface to allow a simple entry and
exit from RTL mode in the UFI/BIOS.
Since the driver is specific to IBM SystemX hardware (x86-
based servers) it only builds on x86 builds. To reduce the
risk of loading on the wrong hardware, the module uses DMI
information and checks a list of servers that are known to
work.
Signed-off-by: Vernon Mauery <vernux@us.ibm.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
CAN has no addressing scheme. It is currently impossible for userspace
to tell is a received CAN frame comes from another process on the local
host, or from a remote CAN device.
This patch add support for userspace applications to distinguish between
'own', 'local' and 'remote' CAN traffic. The distinction is made by returning
flags in msg->msg_flags in the call to recvmsg().
The added documentation explains the introduced flags.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't hold the lock before unregistering the device, since when the
device is unregistered the datastruct containing the lock may be freed
(if the refcount went to 0).
Also fixed the framework documentation that erroneously suggested the
wrong locking order as well.
Reported-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: David Ellingsworth <david@identd.dyndns.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers can optionally set a pointer to a mutex in struct video_device.
The core will use that to lock before calling open, read, write, unlocked_ioctl,
poll, mmap or release.
Updated the documentation as well and ensure that v4l2-event knows about the
lock: it will unlock it before doing a blocking wait on an event and relock it
afterwards.
Ensure that the 'video_is_registered' check is done when the lock is held:
a typical disconnect will take the lock as well before unregistering the
device nodes, so to prevent race conditions the video_is_registered check
should also be done with the lock held.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Until now all fops except release and (unlocked_)ioctl returned an error
after the device node was unregistered. Extend this as well to the ioctl
fops. There is nothing useful that an application can do here and it
complicates the driver code unnecessarily.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver author seems to not worked on this driver since its conversion
from 2.2 to 2.4. Nobody is known to have a stradis hardware for testing. As
it still uses V4L1 API, BKL and probably some other old stuff, someone would
need to work on it to preserve the driver. Instead of investing time and
efforts to keep porting it to work with new API's, it seems better to just
drop the driver.
So, let's move it to drivers/staging and label it to die at 2.6.38, if nobody
cares enough to port parallel port support to gspca or to create a new driver
that uses the same gspca-cpia sub-driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cpia driver were re-written inside gspca driver, for USB devices. The only
functionality that were not migrated is the support for parallel port,
as:
1) the developer didn't find any hardware;
2) it doesn't seem important to keep support for a parallel port webcam,
as this is an obsolete technology;
3) the changes at gspca for it to work with parallel port would be very large;
4) this driver still uses BKL.
So, let's move it to drivers/staging and label it to die at 2.6.38, if nobody
cares enough to port parallel port support to gspca or to create a new driver
that uses the same gspca-cpia sub-driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The VIDIOC_QUERYMENU documentation was not correct. EINVAL can be returned
if the driver does not support some of the menu items. I.e. in a list of
MPEG bitrates a driver generally supports only a subset of these.
This behavior has been in place for years, but was never properly documented.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We forgot to add this capability to the QUERYCAP documentation.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some media devices (microscopes) may have one or many illuminators.
This patch makes them controlable by the applications.
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Teletext interface is provided via VBI interface for a long time. There's no
need nor is there any known program using those old /dev/vtx nodes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove all references to /dev/vtx in the documentation, except for
some historical comments in dev-teletext.xml.
Documentation/devices.txt is not updated, this will go through Alan Cox
who maintains this file.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The existing priv field stores subdev private data owned by the subdev
driver. Host (bridge) drivers might need to store per-subdev
host-specific data, such as a pointer to platform data.
Add a v4l2_subdev host_priv field to store host-specific data, and
rename the existing priv field to dev_priv.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds IRQ_TIME_ACCOUNTING option on x86 and runtime enables it
when TSC is enabled.
This change just enables fine grained irq time accounting, isn't used yet.
Following patches use it for different purposes.
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1286237003-12406-6-git-send-email-venki@google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
SoCs have a standard set of tuples consisting of frequency and
voltage pairs that the device will support per voltage domain. These
are called Operating Performance Points or OPPs. The actual
definitions of OPP varies over silicon versions. For a specific domain,
we can have a set of {frequency, voltage} pairs. As the kernel boots
and more information is available, a default set of these are activated
based on the precise nature of device. Further on operation, based on
conditions prevailing in the system (such as temperature), some OPP
availability may be temporarily controlled by the SoC frameworks.
To implement an OPP, some sort of power management support is necessary
hence this library depends on CONFIG_PM.
Contributions include:
Sanjeev Premi for the initial concept:
http://patchwork.kernel.org/patch/50998/
Kevin Hilman for converting original design to device-based.
Kevin Hilman and Paul Walmsey for cleaning up many of the function
abstractions, improvements and data structure handling.
Romit Dasgupta for using enums instead of opp pointers.
Thara Gopinath, Eduardo Valentin and Vishwanath BS for fixes and
cleanups.
Linus Walleij for recommending this layer be made generic for usage
in other architectures beyond OMAP and ARM.
Mark Brown, Andrew Morton, Rafael J. Wysocki, Paul E. McKenney for
valuable improvements.
Discussions and comments from:
http://marc.info/?l=linux-omap&m=126033945313269&w=2http://marc.info/?l=linux-omap&m=125482970102327&w=2http://marc.info/?t=125809247500002&r=1&w=2http://marc.info/?l=linux-omap&m=126025973426007&w=2http://marc.info/?t=128152609200064&r=1&w=2http://marc.info/?t=128468723000002&r=1&w=2
incorporated.
v1: http://marc.info/?t=128468723000002&r=1&w=2
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If the device which fails to resume is part of a loadable kernel module
it won't be checked at startup against the magic number stored in the
RTC.
Add a read-only sysfs attribute /sys/power/pm_trace_dev_match which
contains a list of newline separated devices (usually just the one)
which currently match the last magic number. This allows the device
which is failing to resume to be found after the modules are loaded
again.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch (as1427) implements the "autosuspend" facility for runtime
PM. A few new fields are added to the dev_pm_info structure and
several new PM helper functions are defined, for telling the PM core
whether or not a device uses autosuspend, for setting the autosuspend
delay, and for marking periods of device activity.
Drivers that do not want to use autosuspend can continue using the
same helper functions as before; their behavior will not change. In
addition, drivers supporting autosuspend can also call the old helper
functions to get the old behavior.
The details are all explained in Documentation/power/runtime_pm.txt
and Documentation/ABI/testing/sysfs-devices-power.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Some devices, such as USB interfaces, cannot be power-managed
independently of their parents, i.e., they cannot be put in low power
while the parent remains at full power. This patch (as1425) creates a
new "no_callbacks" flag, which tells the PM core not to invoke the
runtime-PM callback routines for the such devices but instead to
assume that the callbacks always succeed. In addition, the
non-debugging runtime-PM sysfs attributes for the devices are removed,
since they are pretty much meaningless.
The advantage of this scheme comes not so much from avoiding the
callbacks themselves, but rather from the fact that without the need
for a process context in which to run the callbacks, more work can be
done in interrupt context.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Introduce struct wakeup_source for representing system wakeup sources
within the kernel and for collecting statistics related to them.
Make the recently introduced helper functions pm_wakeup_event(),
pm_stay_awake() and pm_relax() use struct wakeup_source objects
internally, so that wakeup statistics associated with wakeup devices
can be collected and reported in a consistent way (the definition of
pm_relax() is changed, which is harmless, because this function is
not called directly by anyone yet). Introduce new wakeup-related
sysfs device attributes in /sys/devices/.../power for reporting the
device wakeup statistics.
Change the global wakeup events counters event_count and
events_in_progress into atomic variables, so that it is not necessary
to acquire a global spinlock in pm_wakeup_event(), pm_stay_awake()
and pm_relax(), which should allow us to avoid lock contention in
these functions on SMP systems with many wakeup devices.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
The default hibernation image size is currently hard coded and euqal
to 500 MB, which is not a reasonable default on many contemporary
systems. Make it equal 2/5 of the total RAM size (this is slightly
below the maximum, i.e. 1/2 of the total RAM size, and seems to be
generally suitable).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: M. Vefa Bicakci <bicave@superonline.com>
Compress hibernation image with LZO in order to save on I/O and
therefore time to hibernate/thaw.
[rjw: Added hibernate=nocompress command line option instead of just
nocompress which would be confusing, fixed a couple of compiler
warnings, fixed kerneldoc comments, minor cleanups.]
Signed-off-by: Bojan Smojver <bojan@rexursive.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Update kprobes.txt about interrupts disabled state inside
kprobes handlers, because optimized probe/boosted kretprobe
run without disabling interrrupts on x86.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: 2nddept-manager@sdl.hitachi.co.jp
LKML-Reference: <20101014031018.4100.64883.stgit@ltc236.sdl.hitachi.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Updates to Phonet doc for Pipe controller 'connect' socket
implementation and changes related to socket options.
Signed-off-by: Kumar Sanghvi <kumar.sanghvi@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add information about use of the C={1,2} make flag
- Add a description of the new chain mode mechanism
- Add a link to the wiki
Signed-off-by: Nicolas Palix <npalix.work@gmail.com>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Also modifiy the document of cell-index in SPI controller. Add the
SPI flash(s25fl128p01) support on p4080ds and mpc8536ds board.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Currently, the default behavior of O_DIRECT writes was allowing
concurrent writing among nodes to the same file, with no cluster
coherency guaranteed (no EX lock held). This can leave stale data in
the cache for buffered reads on other nodes.
The new mount option introduce a chance to choose two different
behaviors for O_DIRECT writes:
* coherency=full, as the default value, will disallow
concurrent O_DIRECT writes by taking
EX locks.
* coherency=buffered, allow concurrent O_DIRECT writes
without EX lock among nodes, which
gains high performance at risk of
getting stale data on other nodes.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Add WQ_MEM_RECLAIM flag which currently maps to WQ_RESCUER, mark
WQ_RESCUER as internal and replace all external WQ_RESCUER usages to
WQ_MEM_RECLAIM.
This makes the API users express the intent of the workqueue instead
of indicating the internal mechanism used to guarantee forward
progress. This is also to make it cleaner to add more semantics to
WQ_MEM_RECLAIM. For example, if deemed necessary, memory reclaim
workqueues can be made highpri.
This patch doesn't introduce any functional change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
The drivers
- ohci1394 (controller driver)
- ieee1394 (core)
- dv1394, raw1394, video1394 (userspace ABI)
- eth1394, sbp2 (protocol drivers)
are replaced by
- firewire-ohci (controller driver)
- firewire-core (core and userspace ABI)
- firewire-net, firewire-sbp2 (protocol drivers)
which are more featureful, better performing, and more secure than the older
drivers; all with a smaller and more modern code base.
The driver firedtv in drivers/media/dvb/firewire/ contains backends to both
ieee1394 and firewire-core. Its ieee1394 backend code can be removed in an
independent commit; firedtv as-is builds and works fine without ieee1394.
The driver pcilynx (an incomplete controller driver) is deleted without
replacement since PCILynx cards are extremely rare. Owners of these cards
use them with the stand-alone bus sniffer driver nosy instead.
The drivers nosy and init_ohci1394_dma which do not interact with either of
the two IEEE 1394 stacks are not affected by the ieee1394 subsystem removal.
There are still some issues with the newer firewire subsystem compared to
the older one:
- The rare and quirky controllers ALi M52xx, Apple UniNorth v1, NVIDIA
NForce2 are even less well supported by firewire-ohci than by ohci1394.
I am looking into the M52xx issue.
- The experimental firewire-net is reportedly less stable than its
experimental cousin eth1394.
- Audio playback of a certain group of audio devices (ones based on DICE
chipset with EAP; supported by prerelease FFADO code) does not work yet.
This issue is still under investigation.
- There were some ieee1394 based out-of-the-mainline drivers. Of them,
only lisight, an audio driver for iSight webcams, seems still useful.
Work is underway to reimplement it on top of firewire-core.
All these remainig issues are minor; they should not stand in the way of
overall better user experience of IEEE 1394 on Linux, together with a
reduction in support efforts and maintenance burden. The coexistence of two
IEEE 1394 kernel driver stacks in the mainline since 2.6.22 shall end now,
as announced earlier this year.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This patch adds a new MTIOCTOP operation MTWEOFI that writes filemarks with
immediate bit set. This means that the drive does not flush its buffer and the
next file can be started immediately. This speeds up writing in applications
that have to write multiple small files.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The current code works like this:
int garbage, status;
socklen_t len = sizeof(status);
/* enable pipe */
setsockopt(fd, SOL_PNPIPE, PNPIPE_ENABLE, &garbage, sizeof(garbage));
/* disable pipe */
setsockopt(fd, SOL_PNPIPE, PNPIPE_DISABLE, &garbage, sizeof(garbage));
/* get status */
getsockopt(fd, SOL_PNPIPE, PNPIPE_INQ, &status, &len);
...which does not follow the usual socket option pattern. This patch
merges all three "options" into a single gettable&settable option,
before Linux 2.6.37 gets out:
int status;
socklen_t len = sizeof(status);
/* enable pipe */
status = 1;
setsockopt(fd, SOL_PNPIPE, PNPIPE_ENABLE, &status, sizeof(status));
/* disable pipe */
status = 0;
setsockopt(fd, SOL_PNPIPE, PNPIPE_ENABLE, &status, sizeof(status));
/* get status */
getsockopt(fd, SOL_PNPIPE, PNPIPE_ENABLE, &status, &len);
This also fixes the error code from EFAULT to ENOTCONN.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Cc: Kumar Sanghvi <kumar.sanghvi@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates a new idmapper system that uses the request-key function to
place a call into userspace to map user and group ids to names. The old
idmapper was single threaded, which prevented more than one request from running
at a single time. This means that a user would have to wait for an upcall to
finish before accessing a cached result.
The upcall result is stored on a keyring of type id_resolver. See the file
Documentation/filesystems/nfs/idmapper.txt for instructions.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
[Trond: fix up the return value of nfs_idmap_lookup_name and clean up code]
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The page-types utility still uses an out of date name for the
unpoison interface: debugfs:hwpoison/renew-pfn
This patch renames and fixes it.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Hardware scan is the prefer method for all iwlwifi devices;
especially for dual-mode functions. Schedule to deprecate the
software scan support in kernel 2.6.40
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Allow sysadmins to configure the number of multicast
membership report sent on a link failure event.
Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds documentation for the e1000e networking driver.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updated the e1000 networking driver documentation.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the documentation for the ixgbevf (ixgbe virtual
function driver).
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few modifications done for consistency, such as adding the shell
prompt for command line examples and trailing slash for directories.
Also corrects the module include header and fixes a few grammar
issues that I introduced.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
smbfs has been scheduled for removal in 2.6.27, so
maybe we can now move it to drivers/staging on the
way out.
smbfs still uses the big kernel lock and nobody
is going to fix that, so we should be getting
rid of it soon.
This removes the 32 bit compat mount and ioctl
handling code, which is implemented in common fs
code, and moves all smbfs related files into
drivers/staging/smbfs.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
What was previously known as via_dmapos_patch, and hard-coded to be
used for VIA and ATI controllers, is now configurable through a module
option. The background is that some VIA controllers seem to prefer
via_dmapos_patch to be turned off.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of win_req_t, drivers are now requested to fill out
struct pcmcia_device *p_dev->resource[2,3,4,5] for up to four iomem
ranges. After a call to pcmcia_request_window(), the windows found there
are reserved and may be used until pcmcia_release_window() is called.
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-mtd@lists.infradead.org
CC: Jiri Kosina <jkosina@suse.cz>
CC: linux-scsi@vger.kernel.org
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
A follow-up to my edit of the first 4 sections.
Shift sections down by one due to the deletion of section 3; grammar
corrections along with some rewording; margin width cleanup; and
change EXTRA_CFLAGS -> ccflags-y.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Omit needless words and sentences; reorganize and tighten sentence structure;
swap sections 2.2 and 2.3 for a more logical flow; remove section 3, therefore
shifting 4->3; add to explanations; and add section on building multiple modules.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Updates the Phonet document with description related to Pipe controller
implementation
Signed-off-by: Kumar Sanghvi <kumar.sanghvi@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds documentation for the new proc interface that allows
modification of the output device configuration. Should be stable and
useful enough now for daily use.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Cc: Joseph Chan <JosephChan@via.com.tw>
Cc: Andrew Morton <akpm@linux-foundation.org>
The current tracing data is not sufficient to deduce the average time
that a callback spends waiting for a grace period to end. Add three
per-CPU counters recording the number of callbacks invoked (ci), the
number of callbacks orphaned (co), and the number of callbacks adopted
(ca). Given the existing callback queue length (ql), the average wait
time in absence of CPU hotplug operations is ql/ci. The units of wait
time will be in terms of the duration over which ci was measured.
In the presence of CPU hotplug operations, there is room for argument,
but ql/(ci-co+ca) won't steer you too far wrong.
Also fixes a typo called out by Lucas De Marchi <lucas.de.marchi@gmail.com>.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The syscall interface is has been replaced by a more flexible
interface since 2.6.0. It is time to work towards discarding
the old interface.
So add a entry in feature-removal-schedule.txt and print a warning
when the interface is used.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
If specified, the directive must be placed at the top of the Kconfig file.
We need to change the grammar to make the mainmenu directive set the
`rootmenu' prompt. This reflect how menu_add_prompt() works internally, ie.
set the prompt of the `current_entry', pointing originally to `rootmenu'.
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Michal Marek <mmarek@suse.cz>
The attribute reflects an interval, not a rate.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
As a convenience, introduce a kernel command line option to enable
NFSROOT debugging messages.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator: wm8350-regulator - fix the logic of checking REGULATOR_MODE_STANDBY mode
regulator: wm831x-ldo - fix the logic to set REGULATOR_MODE_IDLE and REGULATOR_MODE_STANDBY modes
regulator: ab8500 - fix off-by-one value range checking for selector
regulator: 88pm8607 - fix value range checking for accessing info->vol_table
regulator: isl6271a-regulator - fix regulator_desc parameter for regulator_register()
regulator: ad5398 - fix a memory leak
regulator: Update e-mail address for Liam Girdwood
regulator: set max8998->dev to &pdev->dev.
regulator: tps6586x-regulator - fix bit_mask parameter for tps6586x_set_bits()
regulator: tps6586x-regulator - fix value range checking for val
regulator: max8998 - set max8998->num_regulators
regulator: max8998 - fix memory allocation size for max8998->rdev
regulator: tps6507x - remove incorrect comments
regulator: max1586 - improve the logic of choosing selector
regulator: ab8500 - fix the logic to remove already registered regulators in error path
regulator: ab3100 - fix the logic to remove already registered regulators in error path
regulator/ab8500: move dereference below the check for NULL
The drm device drivers currently allow seeking on the
character device but never care about the actual
file position.
When we change the default llseek operation to be
no_llseek, calling llseek on a drm device would
return an error condition, which is an API change.
Explicitly setting noop_llseek lets us keep the
current API.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Fix docbook templates that reference files that do not contain the
expected kernel-doc notation.
Fixes these warnings:
Warning(arch/x86/include/asm/unaligned.h): no structured comments found
Warning(lib/vsprintf.c): no structured comments found
These cause errors in the generated html output, like below, so drop
these lines.
Name
arch/x86/include/asm/unaligned.h - Document generation inconsistency
Oops
Warning
The template for this document tried to insert the structured comment from the file arch/x86/include/asm/unaligned.h at this point, but none was found. This dummy section is inserted to allow generation to continue.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When you don't use !E or !I but only !F, then it's very easy to miss
including some functions, structs etc. in documentation. To help
finding which ones were missed, allow printing out the unused ones as
warnings.
For example, using this on mac80211 yields a lot of warnings like this:
Warning: didn't use docs for DOC: mac80211 workqueue
Warning: didn't use docs for ieee80211_max_queues
Warning: didn't use docs for ieee80211_bss_change
Warning: didn't use docs for ieee80211_bss_conf
when generating the documentation for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: Range check cpu in blk_cpu_to_group
scatterlist: prevent invalid free when alloc fails
writeback: Fix lost wake-up shutting down writeback thread
writeback: do not lose wakeup events when forking bdi threads
cciss: fix reporting of max queue depth since init
block: switch s390 tape_block and mg_disk to elevator_change()
block: add function call to switch the IO scheduler from a driver
fs/bio-integrity.c: return -ENOMEM on kmalloc failure
bio-integrity.c: remove dependency on __GFP_NOFAIL
BLOCK: fix bio.bi_rw handling
block: put dev->kobj in blk_register_queue fail path
cciss: handle allocation failure
cfq-iosched: Documentation help for new tunables
cfq-iosched: blktrace print per slice sector stats
cfq-iosched: Implement tunable group_idle
cfq-iosched: Do group share accounting in IOPS when slice_idle=0
cfq-iosched: Do not idle if slice_idle=0
cciss: disable doorbell reset on reset_devices
blkio: Fix return code for mkdir calls
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: rawmidi: fix the get next midi device ioctl
ALSA: hda - Fix wrong HP pin detection in snd_hda_parse_pin_def_config()
ALSA: seq/oss - Fix double-free at error path of snd_seq_oss_open()
ALSA: msnd-classic: Fix invalid cfg parameter
ALSA: hda - Enable PC-beep for EeePC with ALC269 codec
ALSA: hda - Add errata initverb sequence for CS42xx codecs
ALSA: usb - Release capture substream URBs properly
ALSA: virtuoso: fix setting of Xonar DS line-in/mic-in controls
ALSA: virtuoso: work around missing reset in the Xonar DS Windows driver
ALSA: hda - Add quirk for Lenovo T400s
ALSA: usb-audio: fix detection of vendor-specific device protocol settings
ALSA: usb-audio: Assume first control interface is for audio
ALSA: hda - Add a new hp-laptop model for Conexant 5066, tested on HP G60
VIRTIO_F_BARRIER is deprecated. Replace it with VIRTIO_F_FLUSH
support.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
There's been some recent confusion about error checking GPIO numbers.
briefly, it should be handled mostly during setup, when gpio_request() is
called, and NEVER by expectig gpio_is_valid to report more than
never-usable GPIO numbers.
[akpm@linux-foundation.org: terminate unterminated comment]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Eric Miao" <eric.y.miao@gmail.com>
Cc: "Ryan Mallon" <ryan@bluewatersys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Create attributes:
/sys/devices/system/cpu/cpuX/topology/book_id
/sys/devices/system/cpu/cpuX/topology/book_siblings
which show the book id and the book siblings of a cpu.
Unlike the attributes for SMT and MC these attributes are only present if
CONFIG_SCHED_BOOK is set. There is no reason to pollute sysfs for every
architecture with unused attributes.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20100831082844.435648457@de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
gcc-4.6: kernel/*: Fix unused but set warnings
mutex: Fix annotations to include it in kernel-locking docbook
pid: make setpgid() system call use RCU read-side critical section
MAINTAINERS: Add RCU's public git tree
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: bus speed strings should be const
PCI hotplug: Fix build with CONFIG_ACPI unset
PCI: PCIe: Remove the port driver module exit routine
PCI: PCIe: Move PCIe PME code to the pcie directory
PCI: PCIe: Disable PCIe port services during port initialization
PCI: PCIe: Ask BIOS for control of all native services at once
ACPI/PCI: Negotiate _OSC control bits before requesting them
ACPI/PCI: Do not preserve _OSC control bits returned by a query
ACPI/PCI: Make acpi_pci_query_osc() return control bits
ACPI/PCI: Reorder checks in acpi_pci_osc_control_set()
PCI: PCIe: Introduce commad line switch for disabling port services
PCI: PCIe AER: Introduce pci_aer_available()
x86/PCI: only define pci_domain_nr if PCI and PCI_DOMAINS are set
PCI: provide stub pci_domain_nr function for !CONFIG_PCI configs
Documentation for recent changes to the tunables accept_ra and
forwarding.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix kernel-doc notation in linux/mutex.h and kernel/mutex.c,
then add these 2 files to the kernel-locking docbook as the
Mutex API reference chapter.
Add one API function to mutex-design.txt and correct a typo in
that file.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
LKML-Reference: <20100902154816.6cc2f9ad.randy.dunlap@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This new model adds the following functionality to HP G60:
- Automute of internal speakers
- Autoswitch of internal/external mics
- Remove SPDIF not physically present
BugLink: http://launchpad.net/bugs/587388
Cc: stable@kernel.org
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch add support for Pyra mobile gaming mouse from Roccat.
It provides access to profiles, settings, actual settings etc.
through sysfs attributes.
This driver is conceptual similar to the existing Kone driver.
Userland tools can soon be found at http://sourceforge.net/projects/roccat
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This makes RTAX_RTO_MIN also available to CCID-3, replacing the compile-time
RTO lower bound with a per-route tunable value.
The original Kconfig option solved the problem that a very low RTT (in the
order of HZ) can trigger too frequent and unnecessary reductions of the
sending rate.
This tunable does not affect the initial RTO value of 2 seconds specified in
RFC 5348, section 4.2 and Appendix B. But like the hardcoded Kconfig value,
it allows to adapt to network conditions.
The same effect as the original Kconfig option of 100ms is now achieved by
> ip route replace to unicast 192.168.0.0/24 rto_min 100j dev eth0
(assuming HZ=1000).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a fixed RTO_MIN of 0.2 seconds was found to cause problems for CCID-2
over 802.11g: at least once per session there was a spurious timeout. It
helped to then increase the the value of RTO_MIN over this link.
Since the problem is the same as in TCP, this patch makes the solution from
commit "05bb1fad1cde025a864a90cfeb98dcbefe78a44a"
"[TCP]: Allow minimum RTO to be configurable via routing metrics."
available to DCCP.
This avoids reinventing the wheel, so that e.g. the following works in the
expected way now also for CCID-2:
> ip route change 10.0.0.2 rto_min 800 dev ath0
Luckily this useful rto_min function was recently moved to net/tcp.h,
which simplifies sharing code originating from TCP.
Documentation also updated (plus minor whitespace fixes).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The doctumentation includes a brief introduction to the driver and
explanations of the filtering parameters as well as a discussion
of the need for and working of the filters.
Signed-off-by: Rafi Rubin <rafi@seas.upenn.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
My previous patch erroneously included an
!A line (for some checking I am working on)
that isn't yet supported by the docbook
tools, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a workqueue chapter to the traceopint docbook.
Current book is at: http://www.kernel.org/doc/htmldocs/tracepoint/
Signed-off-by: Jason Baron <jbaron@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
These days the headers we use are in glibc. If those are too old, you can
add the -I lines to get the kernel headers.
In file included from ../../include/linux/if_tun.h:19,
from lguest.c:33:
../../include/linux/types.h:13:2: warning: #warning "Attempt to use kernel headers from user space, see http://kernelnewbies.org/KernelHeaders"
lguest.c: In function ‘setup_tun_net’:
lguest.c:1456: warning: dereferencing pointer ‘sin’ does break strict-aliasing rules
lguest.c:1457: warning: dereferencing pointer ‘sin’ does break strict-aliasing rules
lguest.c:1450: note: initialized from here
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Add a kernel command-line option so the x86 early memory reservation
size can be adjusted at runtime instead of only at compile time.
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <tip-d0cd7425fab774a480cce17c2f649984312d0b55@git.kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
After commit 852972acff (ACPI: Disable
ASPM if the platform won't provide _OSC control for PCIe) control of
the PCIe Capability Structure is unconditionally requested by
acpi_pci_root_add(), which in principle may cause problems to
happen in two ways. First, the BIOS may refuse to give control of
the PCIe Capability Structure if it is not asked for any of the
_OSC features depending on it at the same time. Second, the BIOS may
assume that control of the _OSC features depending on the PCIe
Capability Structure will be requested in the future and may behave
incorrectly if that doesn't happen. For this reason, control of
the PCIe Capability Structure should always be requested along with
control of any other _OSC features that may depend on it (ie. PCIe
native PME, PCIe native hot-plug, PCIe AER).
Rework the PCIe port driver so that (1) it checks which native PCIe
port services can be enabled, according to the BIOS, and (2) it
requests control of all these services simultaneously. In
particular, this causes pcie_portdrv_probe() to fail if the BIOS
refuses to grant control of the PCIe Capability Structure, which
means that no native PCIe port services can be enabled for the PCIe
Root Complex the given port belongs to. If that happens, ASPM is
disabled to avoid problems with mishandling it by the part of the
PCIe hierarchy for which control of the PCIe Capability Structure
has not been received.
Make it possible to override this behavior using 'pcie_ports=native'
(use the PCIe native services regardless of the BIOS response to the
control request), or 'pcie_ports=compat' (do not use the PCIe native
services at all).
Accordingly, rework the existing PCIe port service drivers so that
they don't request control of the services directly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce kernel command line switch pcie_ports= allowing one to
disable all of the native PCIe port services, so that PCIe ports
are treated like PCI-to-PCI bridges.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add some documentation for cfg80211. I'm hoping some of
the regulatory documentation will be filled by somebody
more familiar with it, hint hint! :)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a small problem in the documentation for
ieee80211_request_smps, and a now erroneous
inclusion of enum ieee80211_key_alg, which no
longer exists after the change to ciphers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves mac80211 documentation into a new
802.11 bookset and also adds a cfg80211 book
to the set. All of this is rather incomplete,
but it's easier to work with big code moving
as a separate patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-upstream/pvhvm' of git://xenbits.xensource.com/people/ianc/linux-2.6:
xen: pvhvm: make it clearer that XEN_UNPLUG_* define bits in a bitfield
xen: pvhvm: rename xen_emul_unplug=ignore to =unnnecessary
xen: pvhvm: allow user to request no emulated device unplug
CPU-bound real-time processes can cause RCU CPU stall warnings, and
much other trouble as well. Document the fact that they can cause
RCU CPU stall warnings.
Suggested-by: Darren Hart <dvhltc@us.ibm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
With the recent innovations in CPU hardware acceleration technologies
from Intel and AMD, VMware ran a few experiments to compare these
techniques to guest paravirtualization technique on VMware's platform.
These hardware assisted virtualization techniques have outperformed the
performance benefits provided by VMI in most of the workloads. VMware
expects that these hardware features will be ubiquitous in a couple of
years, as a result, VMware has started a phased retirement of this
feature from the hypervisor.
Please note that VMI has always been an optimization and non-VMI kernels
still work fine on VMware's platform.
Latest versions of VMware's product which support VMI are,
Workstation 7.0 and VSphere 4.0 on ESX side, future maintainence
releases for these products will continue supporting VMI.
For more details about VMI retirement take a look at this,
http://blogs.vmware.com/guestosguide/2009/09/vmi-retirement.html
This feature removal was scheduled for 2.6.37 back in September 2009.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
LKML-Reference: <1282600151.19396.22.camel@ank32.eng.vmware.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
It is not immediately clear what this option causes to become
ignored. The actual meaning is that it is not necessary to unplug the
emulated devices to safely use the PV ones, even if the platform does
not support the unplug protocol. (pressumably the user will only add
this option if they have ensured that their domain configuration is
safe).
I think xen_emul_unplug=unnecessary better captures this.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Stefano Stabellini <Stefano.Stabellini@eu.citrix.com>
this allows the user to disable pvhvm and revert to emulated devices
in case of a system misconfiguration (e.g. initramfs with only
emulated drivers in it).
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Stefano Stabellini <Stefano.Stabellini@eu.citrix.com>
Some documentation to provide help with tunables.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This list moved to lists.ozlabs.org quite some time ago.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chapter 6 is right about mutex_trylock, but chapter 10 wasn't. This error
was introduced during semaphore-to-mutex conversion of the Unreliable
guide. :-)
If user context which performs mutex_lock() or mutex_trylock() is
preempted by interrupt context which performs mutex_trylock() on the same
mutex instance, a deadlock occurs. This is because these functions do not
disable local IRQs when they operate on mutex->wait_lock.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit 7721fea3d0 ("hwmon:
f71882fg: add support for the Fintek F71808E").
Hans said:
: A second review after I've received a data sheet for this device from
: Fintek has turned up a few bugs.
:
: Unfortunately Giel (nor I) have time to fix this in time for the 2.6.36
: cycle. Therefor I would like to see this patch reverted as not having any
: support for the hwmon function of this superio chip is better then having
: unreliable support.
Cc: Giel van Schijndel <me@mortis.eu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a section describing PROVE_RCU, DEBUG_OBJECTS_RCU_HEAD, and
the __rcu sparse checking to the RCU checklist.
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
This patch removes the abstraction introduced by the union skb_shared_tx in
the shared skb data.
The access of the different union elements at several places led to some
confusion about accessing the shared tx_flags e.g. in skb_orphan_try().
http://marc.info/?l=linux-netdev&m=128084897415886&w=2
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'merge-devicetree' of git://git.secretlab.ca/git/linux-2.6:
spi.h: missing kernel-doc notation, please fix
of: fix missing headers for of_address_to_resource() in MTD and SysACE drivers
of: Fix missing includes
ata: update for of_device to platform_device replacement
microblaze: Fix of: eliminate of_device->node and dev_archdata->{of,prom}_node
microblaze: Fix of/address: Merge all of the bus translation code
booting-without-of: Remove nonexistent chapters from TOC, fix numbering
Marvell and GPIO bindings live in their own files, so the TOC should not
mention them.
Also fix chapters numbering.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
acpi_video_backlight_support() already tells us if ACPI is handling
backlight control through the generic ACPI handle. It is better to just
trust it.
While at it, adjust down a printk priority, and test earlier for
brightness_enable=0.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
kernel-parameters.txt lists 'noreplace-paravirt' parameter as being
limited to X86-32, which is incorrect -- it's actually supported by
x86-32, x86-64 and ia-64.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
gcc-4.6: ACPI: fix unused but set variables in ACPI
ACPI thermal: make procfs I/F depend on CONFIG_ACPI_PROCFS
ACPI video: make procfs I/F depend on CONFIG_ACPI_PROCFS
ACPI processor: remove deprecated ACPI procfs I/F
ACPI power_resource: remove unused procfs I/F
ACPI: remove deprecated ACPI procfs I/F
ACPI: introduce drivers/acpi/sysfs.c
ACPI: introduce module parameter acpi.aml_debug_output
ACPI: introduce drivers/acpi/debugfs.c
ACPI, APEI, ERST debug support
ACPI, APEI, Manage GHES as platform devices
ACPI, APEI, Rename CPER and GHES severity constants
ACPI, APEI, Fix a typo of error path of apei_resources_request
ACPI / ACPICA: Fix reference counting problems with GPE handlers
ACPI: Add the check of ADR flag in course of finding ACPI handle for PCI device
ACPI / Sleep: Drop acpi_suspend_finish()
ACPI / Sleep: Consolidate suspend and hibernation routines
ACPI / Wakeup: Simplify enabling of wakeup devices
ACPI / Sleep: Rework enabling wakeup devices
ACPI / Sleep: Free NVS copy if suspending of devices fails
Fixed up totally buggered "ACPI: fix unused but set variables in ACPI"
patch that doesn't even compile in the merge.
Thanks to Sedat Dilek <sedat.dilek@googlemail.com> for noticing the
breakage before I even pulled. And a big "Grrr.." at Len for not even
bothering to compile the tree before asking me to pull.
Introduce module parameter acpi.aml_debug_output.
With acpi.aml_debug_output set, we can get AML debug object output
(Store (AAA, Debug)), even with CONFIG_ACPI_DEBUG cleared.
Together with the runtime custom method mechanism,
we can debug AML code problems without rebuilding the kernel.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/cleanup:
defconfig reduction
kbuild: drop unifdef-y support
archs: replace unifdef-y with header-y
include: replace unifdef-y with header-y
Move SCSI parameters from kernel-parameters.txt to their own text file.
This continues a trend of moving non-core parameters out of
kernel-parameters.txt.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: (22 commits)
hwmon: (via-cputemp) Remove bogus "SHOW" global variable
hwmon: jc42 depends on I2C
hwmon: (pc87427) Add a maintainer
hwmon: (pc87427) Move sysfs file removal to a separate function
hwmon: (pc87427) Add temperature monitoring support
hwmon: (pc87427) Add support for the second logical device
hwmon: (pc87427) Add support for manual fan speed control
hwmon: (pc87427) Minor style cleanups
hwmon: (pc87427) Handle disabled fan inputs properly
hwmon: (w83627ehf) Add support for W83667HG-B
hwmon: (w83627ehf) Driver cleanup
hwmon: Add driver for SMSC EMC2103 temperature monitor and fan controller
hwmon: Remove in[0-*]_fault from sysfs-interface
hwmon: Add 4 current alarm/beep attributes to sysfs-interface
hwmon: Add 3 critical limit attributes to sysfs-interface
hwmon: (asc7621) Clean up and improve detect function
hwmon: (it87) Export labels for internal sensors
hwmon: (lm75) Add suspend/resume feature
hwmon: (emc1403) Add power support
hwmon: (ltc4245) Expose all GPIO pins as analog voltages
...
Add support for the 6 temperature monitoring channels of the PC87427.
Note that the sensors resolution can vary, and I couldn't find a way
to figure it out, so we might have to compensate in user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add initial support for PWM outputs of the PC87427 Super-I/O chip.
Only mode change and manual fan speed control are supported. Automatic
mode configuration isn't supported, and won't be until at least one
board is known, which makes uses of the PWM outputs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add support for W83667HG-B (very similar to the W83667HG).
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
SMSC's EMC2103 family of temperature/fan controllers have 1
onboard and up to 3 external temperature sensors, and allow
closed-loop control of one fan. This patch adds support for
them.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fault files are for hardware failures that can be reported. So far
we've seen chips reporting such failures for temperature sensors and
fans, but not for voltages. Remove in[0-*]_fault for now. It can be
added back later if really needed, but I doubt it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add currX_alarm, currX_min_alarm, currX_max_alarm and currX_beep
attributes to the hwmon sysfs API.
currX_min_alarm and currX_max_alarm are already supported by the LTC4215
and LTC4245 drivers. currX_alarm is supported by the LTC4261 driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Added _lcrit and _crit to voltage attributes.
Added _lcrit to temperature attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for exposing all GPIO pins as analog voltages. Though this is
not an ideal use of the chip, some hardware engineers may decide that the
LTC4245 meets their design requirements when studying the datasheet.
The GPIO pins are sampled in round-robin fashion, meaning that a slow
reader will see stale data. A userspace application can detect this,
because it will get -EAGAIN when reading from a sysfs file which contains
stale data.
Users can choose to use this feature on a per-chip basis by using either
platform data or the OF device tree (where applicable).
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
ARCH_KMALLOC_MINALIGN was renamed to ARCH_DMA_MINALIGN (the commit
a6eb9fe105).
ARCH_DMA_MINALIGN must be defined instead of ARCH_KMALLOC_MINALIGN to
ensure that kmalloc'ed buffer is DMA-safe.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The last user is gone, so we can safely remove this
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: John Kacur <jkacur@redhat.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Its hardware is handled more fully by the new azt1605/azt2316 drivers.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a new driver for Aztech Sound Galaxy ISA soundcards based on the
AZT1605 and AZT2316 chipsets. It's constructed as two seperate drivers
for either chipset generated from the same source file, with (very)
minimal ifdeffery.
The drivers check the SB DSP version to decide if they are being loaded
for the right chip. AZT1605 returns 2.1 by default and AZT2316 3.1.
This isn't full-proof as the DSP version can actually be set through
software but it's close enough -- as far as I've been able to see, the
DSP version can not be stored in the EEPROM and the cards will therefore
startup with the defaults.
This distinction could (with the same success rate) also be used to
decide which chip we're looking at at runtime meaning a single, merged
driver is also an option but I feel it's actually nicer this way. A
merged driver would have to postpone translating the passed in resource
values to the card configuration until it knew which one it was looking
at and would need to postpone erring out on mpu_irq=10 for azt1605 and
mpu_irq=3 for azt2316.
The drivers have been tested on various cards. For snd-azt1605:
FCC-ID I38-MMSN811: Aztech Sound Galaxy Nova 16 Extra
FCC-ID I38-MMSN822: Aztech Sound Galaxy Pro 16 II
and for snd-azt2316:
FCC-ID I38-MMSN824: Aztech Sound Galaxy Pro 16 AB
FCC-ID I38-MMSN826: Trust Sound Expert DeLuxe Wave 32 (05201)
FCC-ID I38-MMSN830: Trust Sound Expert DeLuxe 16+ (05202)
FCC-ID I38-MMSN837: Packard Bell ISA Soundcard 030069
FCC-ID I38-MMSN846: Trust Sound Expert DeLuxe 16-3D (06300)
FCC-ID I38-MMSN847: Trust Sound Expert DeLuxe Wave 32-3D (06301)
FCC-ID I38-MMSN852: Aztech Sound Galaxy Waverider Pro 32-3D
826 and 846 were also marketed directly by Aztech and then known as:
FCC-ID I38-MMSN826: Aztech Sound Galaxy Waverider 32+
FCC-ID I38-MMSN846: Aztech Sound Galaxy Nova 16 Extra II-3D
Together, these cover the AZT1605 and AT2316A, AZT2316R and AZT2316-S
chipsets. All cards work fully -- full-duplex PCM, MIDI and FM. Full
duplex is a little flaky on some.
I38-MSN811 tends to not work in full-duplex but sometimes does with the
highest success rate being achieved when you first start the capture and
then a playback instead of the other way around (it's a CS4231-KL
codec).
The cards with an AD1845XP codec (my I38-MMSN826 and one of my
I38-MMSN830s) are also somewhat duplex-challenged. Sometimes full-duplex
works, sometimes not and this varies from try to try. This seems likely
to be a timing problem somewhere inside wss-lib.
I38-MMSN826 has an additional "ICS2115 WaveFront" wavetable synth
onboard that isn't supported yet. The wavetable synths on I38-MMSN847
and I38-MMSN852 are wired directly to the standard MPU-401 UART and the
AUX1 input on the codec and work without problem.
CD-ROM audio on the cards is routed to the codec "Line" input, Line-In
to its Aux input, and FM/Wavetable to its AUX1 input. I did not rename
the controls due to the capture source enumeration: I see that
capture-source overrides are hardcoded in wss-lib and this is just too
ugly to live.
Versus the old snd-sgalaxy driver these drivers add support for the
models without a configuration EEPROM (which are common), full-duplex,
MPU-401 UART and OPL3. In the future they might grow support for that
ICS2115 WaveFront synth on 826 and an hwdep interface to write to the
EEPROM on the models that have one.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm: (33 commits)
dm mpath: support discard
dm stripe: support discards
dm: split discard requests on target boundaries
dm stripe: optimize sector division
dm stripe: move sector translation to a function
dm: error return error for discards
dm delay: support discard
dm: zero silently drop discards
dm: use dm_target_offset macro
dm: factor out max_io_len_target_boundary
dm: use common __issue_target_request for flush and discard support
dm: linear support discard
dm crypt: simplify crypt_ctr
dm crypt: simplify crypt_config destruction logic
dm: allow autoloading of dm mod
dm: rename map_info flush_request to target_request_nr
dm ioctl: refactor dm_table_complete
dm snapshot: implement merge
dm: do not initialise full request queue when bio based
dm ioctl: make bio or request based device type immutable
...
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: I2C bus multiplexer driver pca954x
i2c: Multiplexed I2C bus core support
i2c: Use a separate mutex for userspace client lists
i2c: Make i2c_default_probe self-sufficient
i2c: Drop dummy variable
i2c: Move adapter locking helpers to i2c-core
V4L/DVB: Use custom I2C probing function mechanism
i2c: Add support for custom probe function
i2c-dev: Use memdup_user
i2c-dev: Remove unnecessary kmalloc casts
* 'params' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: (22 commits)
param: don't deref arg in __same_type() checks
param: update drivers/acpi/debug.c to new scheme
param: use module_param in drivers/message/fusion/mptbase.c
ide: use module_param_named rather than module_param_call
param: update drivers/char/ipmi/ipmi_watchdog.c to new scheme
param: lock if_sdio's lbs_helper_name and lbs_fw_name against sysfs changes.
param: lock myri10ge_fw_name against sysfs changes.
param: simple locking for sysfs-writable charp parameters
param: remove unnecessary writable charp
param: add kerneldoc to moduleparam.h
param: locking for kernel parameters
param: make param sections const.
param: use free hook for charp (fix leak of charp parameters)
param: add a free hook to kernel_param_ops.
param: silence .init.text references from param ops
Add param ops struct for hvc_iucv driver.
nfs: update for module_param_named API change
AppArmor: update for module_param_named API change
param: use ops in struct kernel_param, rather than get and set fns directly
param: move the EXPORT_SYMBOL to after the definitions.
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: add AD1980 obsolete information
ASoC: register cache should be 1 byte aligned for 1 byte long register
ALSA: hda - Adding support for new IDT 92HD87XX codecs
ASoC: Fix inverted mute controls for WM8580
ALSA: HDA: Use model=auto for LG R510
ALSA: hda - Update model entries in HD-Audio-Models.txt
ALSA: hda: document VIA models
ALSA: hda - patch_nvhdmi.c: Add missing codec IDs, unify names
ALSA: hda - add support for Conexant CX20584
ALSA: hda - New snd-hda-intel model/pin config for hp dv7-4000
ALSA: hda - Fix missing stream for second ADC on Realtek ALC260 HDA codec
ALSA: hda - Make converter setups sticky
ALSA: hda - Add support for Acer ZGA ALC271 (1025:047c)
sound/oss: Adjust confusing if indentation
sound: oss: au1550_ac97.c removed duplicated #include
ASoC: Fix for changed Eureka Kconfig symbol names
SD/MMC cards tend to support an erase operation. In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.
SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.
"erase_size" is the minimum size, in bytes, of an erase operation. For
MMC, "erase_size" is the erase group size reported by the card. Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector. For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.
SD/MMC cards can erase an arbitrarily large area up to and
including the whole card. When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:
1. A single erase command will make all other I/O on the card
wait. This is not a problem if the whole card is being erased, but
erasing one partition will make I/O for another partition on the
same card wait for the duration of the erase - which could be a
several minutes.
2. To be able to inform the user of erase progress.
3. The erase timeout becomes too large to be very useful.
Because the erase timeout contains a margin which is multiplied by
the size of the erase area, the value can end up being several
minutes for large areas.
"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.
For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.
For SD, "preferred_erase_size" is the allocation unit size specified by
the card.
"preferred_erase_size" is in bytes.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add devname:mapper/control and MAPPER_CTRL_MINOR module alias
to support dm-mod module autoloading.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Peter Rajnoha <prajnoha@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The probe method used by i2c_new_probed_device() may not be suitable
for all cases. Let the caller provide its own, optional probe
function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/pkl/squashfs-linus:
Squashfs: fix checkpatch.pl warnings
Squashfs: fix filename typo
Squashfs: update Kconfig and documentation for LZO
Squashfs: fix block size use in LZO decompressor
Squashfs: Add LZO compression support
squashfs: fix filename in header comment
Squashfs: Make XATTR config name consistent with other file systems
squashfs: fix compiler inline warning
Simply replace the whole kfifo.c and kfifo.h files with the new generic
version and fix the kerneldoc API template file.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To keep panic_timeout accuracy when running under a hypervisor, the
current implementation only spins on long time (1 second) calls to mdelay.
That brings a good effect, but the problem is the keyboard LEDs don't
blink at all on that situation.
This patch changes to call to panic_blink_enter() between every mdelay and
keeps blinking in spite of long spin timer mode.
The time to call to mdelay is now 100ms. Even this change will keep
panic_timeout accuracy enough when running under a hypervisor.
Signed-off-by: TAMUKI Shoichi <tamuki@linet.gr.jp>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
DMA_xxBIT_MASK macros were marked as deprecated in June 2009. One more
year is long enough, I think.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It was replaced with the DMA unamp state API (which can be used for
any bus).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Architectures implement dma_is_consistent() in different ways (some
misinterpret the definition of API in DMA-API.txt). So it hasn't been so
useful for drivers. We have only one user of the API in tree. Unlikely
out-of-tree drivers use the API.
Even if we fix dma_is_consistent() in some architectures, it doesn't look
useful at all. It was invented long ago for some old systems that can't
allocate coherent memory at all. It's better to export only APIs that are
definitely necessary for drivers.
Let's remove this API.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix typos & grammar.
Use CPU instead of cpu in text.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The exception.txt has been removed from the Documentation directory. So
update the index file for it.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
$ rm -rf build
$ mkdir build
$ cp .config build
$ make O=build htmldocs
...
xmlto: linux-2.6/build/Documentation/DocBook/media.xml
does not validate (status 3)
xmlto: Fix document syntax or use --skip-validation option
linux-2.6/build/Documentation/DocBook/media.xml:4:
warning: failed to load external entity
"linux-2.6/build/Documentation/DocBook/media-entities.tmpl"
We need the xmldoclinks built for any document types built from the
XML sources.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Andy Whitcroft <apw@canonical.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 1d794e3b35 ("Staging: wavelan: delete the driver") removed the
source, so remove the documentation as well.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Jean Tourrilhes <jt@hpl.hp.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Be more consistent about runtime programming interface abuse warnings,
which can reduce some confusion and trigger bugfixes. Based on an
observation and patch from Jani Nikula.
Also update doc to highlight some sleeping-call issues and to match some
recent changes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jani Nikula <ext-jani.1.nikula@nokia.com>
Cc: "Ryan Mallon" <ryan@bluewatersys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Cc: Jerry Huang <Chang-Ming.Huang@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'make htmldocs' produces errors due to missing a supporting media
file, so add 'xmldoclinks' to the htmldocs dependencies so that the
needed supporting file will be present.
Documentation/DocBook/media.xml:4: warning: failed to load external entity "Documentation/DocBook/media-entities.tmpl"
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (94 commits)
V4L/DVB: tvp7002: fix write to H-PLL Feedback Divider LSB register
V4L/DVB: dvb: siano: free spinlock before schedule()
V4L/DVB: media: video: pvrusb2: remove custom hex_to_bin()
V4L/DVB: drivers: usbvideo: remove custom implementation of hex_to_bin()
V4L/DVB: Report supported QAM modes on bt8xx
V4L/DVB: media: ir-keytable: null dereference in debug code
V4L/DVB: ivtv: convert to the new control framework
V4L/DVB: ivtv: convert gpio subdev to new control framework
V4L/DVB: wm8739: convert to the new control framework
V4L/DVB: cs53l32a: convert to new control framework
V4L/DVB: wm8775: convert to the new control framework
V4L/DVB: cx2341x: convert to the control framework
V4L/DVB: cx25840: convert to the new control framework
V4L/DVB: cx25840/ivtv: replace ugly priv control with s_config
V4L/DVB: saa717x: convert to the new control framework
V4L/DVB: msp3400: convert to the new control framework
V4L/DVB: saa7115: convert to the new control framework
V4L/DVB: v4l2: hook up the new control framework into the core framework
V4L/DVB: Documentation: add v4l2-controls.txt documenting the new controls API
V4L/DVB: v4l2-ctrls: Whitespace cleanups
...
MS Windows mounts removable storage in "Removal optimized mode" by
default. All the writes to the media are synchronous which is achieved
by setting FUA (Force Unit Access) bit in SCSI WRITE(10,12) commands.
This prevents I/O requests aggregation in block layer dramatically
decreasing performance.
This patch brings an option to accept or ignore mentioned bit
a) via specifying module parameter "nofua", or
b) through sysfs entry
/sys/devices/platform/_UDC_/gadget/gadget-lunX/nofua
(_UDC_ is the name of the USB Device Controller driver)
Patch is based on the work that was done by Denis Karpov for Maemo 5
platform.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A short documentation of the g_multi driver along with INF
files for Windows XP SP3 are provided.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Updated the INF file for g_serial gadget. It should work with
most recent Windows systems now.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Updated the INF file for the g_ether gadget. It should work with most
recent Windows systems now.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linus Torvalds