The pllv3 nees relock not only when powering up but also when rate
changes. The patch creates a helper function clk_pllv3_wait_lock() and
moves the relock code from clk_pllv3_prepare() into there, so that
both .prepare() and .set_rate() hooks of pllv3 can call into the helper
for relocking.
Since relock is only needed when PLL is powered up while clk_set_rate()
could be called before clk is prepared, we need to add a check in
clk_pllv3_wait_lock() to skip the relock if PLL is not powered.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The pllv3 relock time varies in the range of 50us ~ 500us, depending on
the specific PLL type, e.g. 50us for ARM PLL and 450us for Audio/Video
PLL. Let's add a usleep_range() call instead of doing busy wait during
relock.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The clk_enet_ref_table[] is missing a final empty entry as end of list
marker. Also make the existing markers more obvious.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Building a kernel with the following options,
CONFIG_SMP=n
CONFIG_PM=y
CONFIG_SOC_IMX6SL=y
CONFIG_SOC_IMX6Q=n
we will see the build error below.
arch/arm/mach-imx/built-in.o: In function `imx6q_pm_enter':
platform-spi_imx.c:(.text+0x2648): undefined reference to `v7_cpu_resume'
make[1]: *** [vmlinux] Error 1
This is because that v7_cpu_resume() implemented in headsmp.S is also
needed by imx6sl build. Let's build headsmp.S for CONFIG_SOC_IMX6SL as
well.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The current comment in the code does not make it clear why the double writes
on SRC bit is needed. Let's quote the errata to get it clear. Also, to
ensure there are at least 2 writes happen in the same one 32kHz period,
we actually need 3 writes. Let's add the third one.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
There is ~10% possibility that the following emergency restart command
fails to reboot imx6q.
$ echo b > /proc/sysrq-trigger
The IMX restart routine mxc_restart() assumes that it will always run on
primary core, and will call imx_src_prepare_restart() to disable
secondary cores in order to get them come to online in the following
boot. However, the assumption is only true for normal kernel_restart()
case where migrate_to_reboot_cpu() will be called to migrate to primary
core, but not necessarily true for emergency_restart() case. So when
emergency_restart() calls into mxc_restart() on any secondary core,
system will hang immediately once imx_src_prepare_restart() is called
to disabled secondary cores. Since emergency_restart() is defined as a
function that is safe to call in interrupt context, we cannot just call
migrate_to_reboot_cpu() to fix the issue.
Fortunately, we just found that the issue can be fixed at imx6q platform
level. We used to call imx_src_prepare_restart() to disable all
secondary cores before resetting hardware. Otherwise, the secondary
will fail come to online in the reboot. However, we recently found that
after commit 6050d18 (ARM: imx: reset core along with enable/disable
operation) comes to play, we do not need to reset the secondary cores
any more. That said, mxc_restart() now can run on any core to reboot
the system, as long as we remove the imx_src_prepare_restart() call from
mxc_restart().
So let's simply remove imx_src_prepare_restart() call to fix the above
emergency restart failure.
Reported-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
instead of pll3_usb_otg the parent of can_root clock
should be pll3_60m.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
New and updated SoC support. Among the things new for this release are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as ARCH_BCM,
and turned out to be too broad a name. New name is ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the platform code
more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is more work
on consolidation instead of introduction of new non-multiplatform SoCs, we're
all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WYJl
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Among the things new for this release
are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as
ARCH_BCM, and turned out to be too broad a name. New name is
ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the
platform code more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is
more work on consolidation instead of introduction of new
non-multiplatform SoCs, we're all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates,
etc"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (159 commits)
ARM: bcm281xx: Add ARCH_BCM_MOBILE to bcm config
ARM: bcm_defconfig: Run "make savedefconfig"
ARM: bcm281xx: Add ARCH Timers to config
rename ARCH_BCM to ARCH_BCM_MOBILE (mach-bcm)
ARM: vexpress: Enable platform-specific options in defconfig
ARM: vexpress: Make defconfig work again
ARM: sunxi: remove .init_time hooks
ARM: imx: enable suspend for imx6sl
ARM: imx: ensure dsm_request signal is not asserted when setting LPM
ARM: imx6q: call WB and RBC configuration from imx6q_pm_enter()
ARM: imx6q: move low-power code out of clock driver
ARM: imx: drop extern with function prototypes in common.h
ARM: imx: reset core along with enable/disable operation
ARM: imx: do not return from imx_cpu_die() call
ARM: imx_v6_v7_defconfig: Select CONFIG_PROVE_LOCKING
ARM: imx_v6_v7_defconfig: Enable LEDS_GPIO related options
ARM: mxs_defconfig: Turn off CONFIG_DEBUG_GPIO
ARM: imx: replace imx6q_restart() with mxc_restart()
ARM: mach-imx: mm-imx5: Retrieve iomuxc base address from dt
ARM: mach-imx: mm-imx5: Retrieve tzic base address from dt
...
Since Operating Performance Points (OPP) functions are specific
to device specific power management, be specific and rename opp.h
to pm_opp.h
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since Operating Performance Points (OPP) functions are specific to
device specific power management, be specific and rename opp_*
accessors in OPP library with dev_pm_opp_* equivalent.
Affected functions are:
opp_get_voltage
opp_get_freq
opp_get_opp_count
opp_find_freq_exact
opp_find_freq_floor
opp_find_freq_ceil
opp_add
opp_enable
opp_disable
opp_get_notifier
opp_init_cpufreq_table
opp_free_cpufreq_table
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The imx6sl low power mode implementation inherits imx6q/dl one,
and pm-imx6q.c can just work for imx6sl with some minor updates.
Let's enable imx6sl suspend support by reusing pm-imx6q.c and use
cpu_is_imxXX() to handle the those minor differences between imx6sl
and imx6q/dl.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
There is a defect in imx6 LPM design. When SW tries to enter low power
mode with following sequence, the chip will enter low power mode before
A9 CPU execute WFI instruction:
1. Set CCM_CLPCR[1:0] to 2'b00;
2. ARM CPU enters WFI;
3. ARM CPU wakeup from an interrupt event, which is masked by GPC or not
visible to GPC, such as interrupt from local timer;
4. Set CCM_CLPCR[1:0] to 2'b01 or 2'b10;
5. ARM CPU execute WFI.
Before the last step, the chip will enter WAIT mode if CCM_CLPCR[1:0] is
set to 2'b01, or enter STOP mode if CCM_CLPCR[1:0] is set to 2'b10.
The patch implements a recommended workaround for this issue.
1. SW triggers irq #32(IOMUX) to be always pending manually by setting
IOMUX_GPR1_GINT bit;
2. SW should then unmask it in GPC before setting CCM LPM;
3. SW should mask it right after CCM LPM is set (bit0-1 of CCM_CLPCR).
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The WB and RBC configuration calls are currently made from
imx6q_set_lpm() for WAIT_CLOCKED and WAIT_UNCLOCKED mode with a simple
state tracking. This becomes unnecessary since we can make the calls
from imx6q_pm_enter() directly now for suspend.
More importantly, the current call of imx6q_enable_wb() from
imx6q_set_lpm() is buggy. The CLPCR register bits configured by
imx6q_enable_wb() will get lost, because imx6q_set_lpm() caches the same
register and write it back at the end of the function. That's why the
imx6dl suspend/resume does not work currently - the wakeup from suspend
triggers a reset on imx6dl.
Moves the WB and RBC calls into imx6q_pm_enter() to save the state
tracking and fixes above bug, so that suspend/resume can start working
on imx6dl.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The LPM (Low Power Mode) code that currently sits in imx6q clock driver
will be reused by imx6sl. Let's move it into pm-imx6q.c, so that we
can keep clock driver SoC specific and reuse pm-imx6q.c on imx6sl.
In order to avoid adding another ioremap for CCM block,
imx6q_pm_set_ccm_base() is created to let clock driver set up ccm_base
for pm code.
During the move, the unused CCGR macros get removed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since commit 70dc8a4 (checkpatch: warn when using extern with function
prototypes in .h files), we will get checkpatch warning when updating
common.h following the existing convention which has extern for function
prototypes.
Let's change the convention to not use extern with function prototypes
in this header.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
From hotplug stress test result, resetting core during enable/disable
operation can improve cpu hotplug stability. So let's set
SRC reset bit in imx_enable_cpu() for the core when its enable bit is
accessed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
When imx_cpu_die() is being called, the cpu should never return from the
call but just in WFI and wait for hardware to take it down. So let's
do cpu_do_idle() repeatly in the call. Doing this help improve the
relibility of hotplug operation.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The imx6q_restart() works fine with normal reboot but will run into
problem with emergency reboot like sysrq-b. In that case, of_iomap()
gets called from interrupt context and hence triggers the BUG_ON in
__get_vm_area_node().
Actually, since commit c1e31d1 (ARM: imx: create
mxc_arch_reset_init_dt() for DT boot), imx6q/dl should try to use
mxc_restart() by calling mxc_arch_reset_init_dt() beforehand, where
things like of_iomap() can be done.
The patch updates mxc_restart() a little bit to get it work for imx6q/dl
and kill imx6q_restart() completely.
Reported-by: Nathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
As mx53 is a dt-only SoC, we should retrieve the iomuxc base address from the
device tree, instead of using the old MX53_IO_ADDRESS method.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
As mx53 is a dt-only SoC, we should retrieve the tzic base address from the
device tree, instead of using the old MX53_IO_ADDRESS method.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
As mx53 is a dt-only SoC, we should retrieve the gpt base address and irq
from the device tree, instead of using the old MX53_IO_ADDRESS method.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The IS_ERR() macro is defined in the linux/err.h header file, so include
it explicitly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The i.MX6 has two general-purpose LVDS clocks that can be driven
from a variety of sources. This patch adds a mux and a gate for
both of these clocks.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The patch enables soc bus infrastructure and adds a function
imx_soc_device_init() to report soc info via soc device interface for
imx6qdl and imx6sl. With the support, user space can get soc related
info by looking at sysfs like below.
$ cat /sys/devices/soc0/machine
Freescale i.MX6 Quad SABRE Smart Device Board
$ cat /sys/devices/soc0/family
Freescale i.MX
$ cat /sys/devices/soc0/soc_id
i.MX6Q
$ cat /sys/devices/soc0/revision
1.2
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add imx6sl support into imx_init_revision_from_anatop(), so that it can
be used to initialize cpu type and revision on imx6sl.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The patch creates a common function imx_init_revision_from_anatop() by
merging imx6q_init_revision() and imx_anatop_get_digprog(), so that any
SoC that encodes revision info in anatop can use it to initialize
revision.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It calls imx_set_soc_revision() to set up soc revision in
imx6q_init_revision(), and replaces all the occurrences of
imx6q_revision() with common helper imx_get_soc_revision().
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Similar to what we do for cpu type, the patch adds helper functions
imx_set_soc_revision() and imx_get_soc_revision() to maintain
imx_soc_revision in cpu.c.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This flag is a NOOP since 2.6.35 and can be removed.
This is an update for 3.11 of a patch already sent for 3.10
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Config iomux-gpr1 to select clock source for fec system clock.
Clear gpr1[14], gpr1[18-17] bit to select the fec clock source
from internal anatop PLL.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
There's a pll4_audio_div clock, an extra divider for pll4, missing
in current clock tree, thus add it.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
CLKDEV_LOOKUP selects HAVE_CLK and COMMON_CLK selects CLKDEV_LOOKUP. So
all symbols that select at least two of these symbols can be simplified.
For imx, omap2 and ux500 some rearrangements were necessary before the
simplification.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Sebastian Hasselbarth:
This is a patch set based on an RFC [1][2] sent earlier to provide
a common arch/arm init for DT clock providers. Currently, the call to
of_clk_init(NULL) to initialize DT clock providers is spread among several
mach-dirs. Since most machs require DT clocks initialized before timers,
no initcall can be used.
By adding of_clk_init(NULL) to arch/arm time_init(), we can remove all
mach-specific .init_time hooks that basically called of_clk_init and
clocksource_of_init.
In contrast to the RFC version, of_clk_init(NULL) is now only called if
no custom .init_time callback is set. This allows some machs to still
call clock init themselves, as not all can be converted now. Therefore,
this patch sets drops conversion of mach-mvebu and mach-zynq. New machs
that were introduced with v3.12-rc1 are also converted, except mach-u300
that requires clocks before irqs.
* 'clk-of-init-v2_for-3.13' of https://github.com/shesselba/linux-dove: (29 commits)
ARM: vt8500: remove custom .init_time hook
ARM: vexpress: remove custom .init_time hook
ARM: tegra: remove custom .init_time hook
ARM: sunxi: remove custom .init_time hook
ARM: sti: remove custom .init_time hook
ARM: socfpga: remove custom .init_time hook
ARM: rockchip: remove custom .init_time hook
ARM: prima2: remove custom .init_time hook
ARM: nspire: remove custom .init_time hook
ARM: nomadik: remove custom .init_time hook
ARM: mxs: remove custom .init_time hook
ARM: kirkwood: remove custom .init_time hook
ARM: imx: remove custom .init_time hook
ARM: highbank: remove custom .init_time hook
ARM: exynos: remove custom .init_time hook
ARM: dove: remove custom .init_time hook
ARM: bcm2835: remove custom .init_time hook
ARM: bcm: provide common arch init for DT clocks
ARM: call of_clk_init from default time_init handler
ARM: vt8500: prepare for arch-wide .init_time callback
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch moves the at24.h header from include/linux/i2c to
include/linux/platform_data and updates existing support accordingly.
It also fixes the following checkpatch warning:
WARNING: please, no space before tabs
#436: FILE: include/linux/platform_data/at24.h:31:
+ * ^Iu8 *mac_addr = ethernet_pdata->mac_addr;$
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
With arch/arm calling of_clk_init(NULL) from time_init(), we can now
remove custom .init_time hooks.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
1) Four fixes for cpufreq regressions introduced by the changes that
removed Device Tree parsing for CPU device nodes from cpufreq
drivers from Sudeep KarkadaNagesha.
2) Two fixes for recent cpufreq regressions introduced by changes
related to the preservation of sysfs attributes over system
suspend/resume cycles from Viresh Kumar.
3) Fix for ACPI-based wakeup signaling in the PCI subsystem that
fails to stop PME polling for devices put into the D3cold power
state from Rafael J Wysocki.
4) Fix for bad interactions between cpufreq and udev on systems
supporting intel_pstate where acpi-cpufreq is available as well
from Yinghai Lu.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=8EeE
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
1) Four fixes for cpufreq regressions introduced by the changes that
removed Device Tree parsing for CPU device nodes from cpufreq
drivers from Sudeep KarkadaNagesha.
2) Two fixes for recent cpufreq regressions introduced by changes
related to the preservation of sysfs attributes over system
suspend/resume cycles from Viresh Kumar.
3) Fix for ACPI-based wakeup signaling in the PCI subsystem that
fails to stop PME polling for devices put into the D3cold power
state from Rafael J Wysocki.
4) Fix for bad interactions between cpufreq and udev on systems
supporting intel_pstate where acpi-cpufreq is available as well
from Yinghai Lu.
* tag 'pm+acpi-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: return EEXIST instead of EBUSY for second registering
PCI / ACPI / PM: Clear pme_poll for devices in D3cold on wakeup
ARM: shmobile: change dev_id to cpu0 while registering cpu clock
ARM: i.MX: change dev_id to cpu0 while registering cpu clock
cpufreq: imx6q-cpufreq: assign cpu_dev correctly to cpu0 device
cpufreq: cpufreq-cpu0: assign cpu_dev correctly to cpu0 device
cpufreq: unlock correct rwsem while updating policy->cpu
cpufreq: Clear policy->cpus bits in __cpufreq_remove_dev_finish()
Currently all clkdev registration use "cpufreq-cpu0.0" as dev_id
for cpu clock which refers to virtual platform device. It needs to
be "cpu0" instead which is actual cpu0 device id.
This patch changes the dev_id from "cpufreq-cpu0.0" to "cpu0".
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit cdc58d602d "cpufreq: imx6q-cpufreq:
remove device tree parsing for cpu nodes" assumed the pdev->dev is set to
cpu0 device in the platform code. But it actually points to the virtual
cpufreq-cpu0 platform device which is not present in the device tree.
Most of the information needed by cpufreq is stored in cpu0 DT node.
So cpu_dev must point to cpu0 device.
This patch fixes the wrong assignment to cpu_dev.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The L2 cache controller(PL310) version on the i.MX6D/Q is r3p1-50rel0
The L2 cache controller(PL310) version on the i.MX6DL/SOLO/SL is r3p2
But according to ARM PL310 errata: 752271
ID: 752271: Double linefill feature can cause data corruption
Fault Status: Present in: r3p0, r3p1, r3p1-50rel0. Fixed in r3p2
Workaround: The only workaround to this erratum is to disable the
double linefill feature. This is the default behavior.
without this patch, you will meet the following error when run the
memtester application at: http://pyropus.ca/software/memtester/
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365664.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365668.
FAILURE: 0x00100000 != 0x00200000 at offset 0x0136566c.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365670.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365674.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365678.
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since commit beb2d1c1ba (ARM i.MX5: Add S/PDIF clocks), the following clock
error appears on mx51:
TrustZone Interrupt Controller (TZIC) initialized
i.MX51 clk 180: register failed with -17
i.MX5 clk 180: register failed with -17
sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
CPU identified as i.MX51, silicon rev 3.0
...
Clock 180 corresponds to 'spdif1_podf' and this clock is getting registered
twice.
Fix it, by properly registering the 'spdif1_pred' clock, which should not
reference 'spdif1_podf'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The clk_init_data.flags of clk-fixup-mux is left there without
initialization. It may hold some random data and cause clock framework
interpret the clock in an unexpected way. At least on imx6sl, the
following division by zero error with sched_clock is seen because of it.
Division by zero in kernel.
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.11.0-rc3+ #19
Backtrace:
[<80011af0>] (dump_backtrace+0x0/0x10c) from [<80011c90>] (show_stack+0x18/0x1c)
r6:3b9aca00 r5:00000020 r4:00000000 r3:00000000
[<80011c78>] (show_stack+0x0/0x1c) from [<8055e02c>] (dump_stack+0x78/0x94)
[<8055dfb4>] (dump_stack+0x0/0x94) from [<80011924>] (__div0+0x18/0x20)
r4:00000000 r3:00000000
[<8001190c>] (__div0+0x0/0x20) from [<8026c408>] (Ldiv0_64+0x8/0x18)
[<8006330c>] (clocks_calc_mult_shift+0x0/0xf8) from [<8072f604>] (setup_sched_clock+0x88/0x1f0)
[<8072f57c>] (setup_sched_clock+0x0/0x1f0) from [<8071ad48>] (mxc_timer_init+0xe8/0x17c)
[<8071ac60>] (mxc_timer_init+0x0/0x17c) from [<807290b0>] (imx6sl_clocks_init+0x1db8/0x1dc0)
r8:807a9ca4 r7:00000000 r6:80777564 r5:8100c1f4 r4:c0820000
[<807272f8>] (imx6sl_clocks_init+0x0/0x1dc0) from [<807420ac>] (of_clk_init+0x40/0x6c)
[<8074206c>] (of_clk_init+0x0/0x6c) from [<807290cc>] (imx6sl_timer_init+0x14/0x18)
r5:807a8e80 r4:ffffffff
[<807290b8>] (imx6sl_timer_init+0x0/0x18) from [<80716e1c>] (time_init+0x24/0x34)
[<80716df8>] (time_init+0x0/0x34) from [<80713738>] (start_kernel+0x1b0/0x310)
[<80713588>] (start_kernel+0x0/0x310) from [<80008074>] (0x80008074)
r7:80770b08 r6:80754cd4 r5:8076c8c4 r4:10c53c7d
sched_clock: 32 bits at 0 Hz, resolution 0ns, wraps every 0ms
Fix the bug by initializing init.flags as zero.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Pull slave-dmaengine updates from Vinod Koul:
"This pull brings:
- Andy's DW driver updates
- Guennadi's sh driver updates
- Pl08x driver fixes from Tomasz & Alban
- Improvements to mmp_pdma by Daniel
- TI EDMA fixes by Joel
- New drivers:
- Hisilicon k3dma driver
- Renesas rcar dma driver
- New API for publishing slave driver capablities
- Various fixes across the subsystem by Andy, Jingoo, Sachin etc..."
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (94 commits)
dma: edma: Remove limits on number of slots
dma: edma: Leave linked to Null slot instead of DUMMY slot
dma: edma: Find missed events and issue them
ARM: edma: Add function to manually trigger an EDMA channel
dma: edma: Write out and handle MAX_NR_SG at a given time
dma: edma: Setup parameters to DMA MAX_NR_SG at a time
dmaengine: pl330: use dma_set_max_seg_size to set the sg limit
dmaengine: dma_slave_caps: remove sg entries
dma: replace devm_request_and_ioremap by devm_ioremap_resource
dma: ste_dma40: Fix potential null pointer dereference
dma: ste_dma40: Remove duplicate const
dma: imx-dma: Remove redundant NULL check
dma: dmagengine: fix function names in comments
dma: add driver for R-Car HPB-DMAC
dma: k3dma: use devm_ioremap_resource() instead of devm_request_and_ioremap()
dma: imx-sdma: Staticize sdma_driver_data structures
pch_dma: Add MODULE_DEVICE_TABLE
dmaengine: PL08x: Add cyclic transfer support
dmaengine: PL08x: Fix reading the byte count in cctl
dmaengine: PL08x: Add support for different maximum transfer size
...
patches, both new drivers and fixes to existing. A high percentage of
these are for Samsung platforms like Exynos. Core framework fixes and
some new features like automagical clock re-parenting round out the
patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJSLkImAAoJEDqPOy9afJhJOjsP/Ri26AW7XB9pPWJRSU9REBZA
31wxcFo2T+PNir9duwDwjFBFycC3MisaKFlg7D134M+7txbYqm1TRvfu9OEDxpSP
4b/Yl6TarN4dhCN2R+BREO8PnxCBVpspDcsdh6Esuwuet2xUom3UtN8yvSjhPP/u
qGNmXQYXyQy4fom5r+GsDVW+HIhLkaX9b0fYc9EN/bqfgv94PMZAxAxsK9CroAGZ
0m0g9ZXw9iSvVfz+iQEqPINtvpTLHk0FGyimoSR7kvW4o4o47tVtLEWp7VjG6mr5
zvBsycaQq6NgxPu96iUWWhsO9Uj2I7/7JgidXF7r+wvEFs1mcgZtkkirSA/n4zUN
C8a87rvQrZRLr+xXhVuqiVHCgCY8vXoHqkWg6SrZ62ORL8C7uYRpog5SEe2ZzLJX
l5uGAsDM6el+Uc/YviCPoZbeFr3h3CQvvFo8+i2eN0v/Phf30rq4lotBvpQj894G
ngEIMj+D8wshdYSF2dNJ0rLnkLHTgCbiA28L6Cl5TRzRMj3Uaj9aT3cmoLUnimZu
7F7nWU4Iu/vzQKCTQ+eTvwxXJqIlE0JeVbJilqH1f2a68JdXP1LOId+2w/CP8gqQ
i2odj6JHMgBzM9rNs+y0Ir9X/bXIVi6F341c19Nl15srEiLLl8xQIpcPDaI/Kvzs
pefYgF2yS5AZAW3ac90r
=5GfA
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.12' of git://git.linaro.org/people/mturquette/linux
Pull clock framework changes from Michael Turquette:
"The common clk framework changes for 3.12 are dominated by clock
driver patches, both new drivers and fixes to existing. A high
percentage of these are for Samsung platforms like Exynos. Core
framework fixes and some new features like automagical clock
re-parenting round out the patches"
* tag 'clk-for-linus-3.12' of git://git.linaro.org/people/mturquette/linux: (102 commits)
clk: only call get_parent if there is one
clk: samsung: exynos5250: Simplify registration of PLL rate tables
clk: samsung: exynos4: Register PLL rate tables for Exynos4x12
clk: samsung: exynos4: Register PLL rate tables for Exynos4210
clk: samsung: exynos4: Reorder registration of mout_vpllsrc
clk: samsung: pll: Add support for rate configuration of PLL46xx
clk: samsung: pll: Use new registration method for PLL46xx
clk: samsung: pll: Add support for rate configuration of PLL45xx
clk: samsung: pll: Use new registration method for PLL45xx
clk: samsung: exynos4: Rename exynos4_plls to exynos4x12_plls
clk: samsung: exynos4: Remove checks for DT node
clk: samsung: exynos4: Remove unused static clkdev aliases
clk: samsung: Modify _get_rate() helper to use __clk_lookup()
clk: samsung: exynos4: Use separate aliases for cpufreq related clocks
clocksource: samsung_pwm_timer: Get clock from device tree
ARM: dts: exynos4: Specify PWM clocks in PWM node
pwm: samsung: Update DT bindings documentation to cover clocks
clk: Move symbol export to proper location
clk: fix new_parent dereference before null check
clk: wm831x: Initialise wm831x pointer on init
...
This branch contains mostly additions and changes to platform enablement
and SoC-level drivers. Since there's sometimes a dependency on device-tree
changes, there's also a fair amount of those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving
MSI arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fJ5x
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This branch contains mostly additions and changes to platform
enablement and SoC-level drivers. Since there's sometimes a
dependency on device-tree changes, there's also a fair amount of
those in this branch.
Pieces worth mentioning are:
- Mbus driver for Marvell platforms, allowing kernel configuration
and resource allocation of on-chip peripherals.
- Enablement of the mbus infrastructure from Marvell PCI-e drivers.
- Preparation of MSI support for Marvell platforms.
- Addition of new PCI-e host controller driver for Tegra platforms
- Some churn caused by sharing of macro names between i.MX 6Q and 6DL
platforms in the device tree sources and header files.
- Various suspend/PM updates for Tegra, including LP1 support.
- Versatile Express support for MCPM, part of big little support.
- Allwinner platform support for A20 and A31 SoCs (dual and quad
Cortex-A7)
- OMAP2+ support for DRA7, a new Cortex-A15-based SoC.
The code that touches other architectures are patches moving MSI
arch-specific functions over to weak symbols and removal of
ARCH_SUPPORTS_MSI, acked by PCI maintainers"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (266 commits)
tegra-cpuidle: provide stub when !CONFIG_CPU_IDLE
PCI: tegra: replace devm_request_and_ioremap by devm_ioremap_resource
ARM: tegra: Drop ARCH_SUPPORTS_MSI and sort list
ARM: dts: vf610-twr: enable i2c0 device
ARM: dts: i.MX51: Add one more I2C2 pinmux entry
ARM: dts: i.MX51: Move pins configuration under "iomuxc" label
ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog
ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator
ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX
ARM: dts: i.MX27: Disable AUDMUX in the template
ARM: dts: wandboard: Add support for SDIO bcm4329
ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
ARM: dts: imx53-qsb: Make USBH1 functional
ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
ARM: dts: imx6qdl-sabresd: Add touchscreen support
ARM: imx: add ocram clock for imx53
ARM: dts: imx: ocram size is different between imx6q and imx6dl
ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
ARM: dts: i.MX27: Remove clock name from CPU node
...
This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM driver
and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM platform
code for include changes so we took it through our tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSKg/NAAoJEIwa5zzehBx3vxIP/19ouV4WrzOeEMz2Id8bYT5/
Tu9HRm+PJJ2O+4P+DYlycRAEHsbuDbwgdcqToH3quca1YnIcoJgY0FA6D0ihQ5uE
EvTgFIpkNMLnR43GYDOE3a/rR3hYPg5oQabKFn7ZGLG2ND3D3d2N05WT8XNbTYDk
nvCXvyRRT1ynCEzbxRBiE8x62ao4bqa5dZ1zrHHIEoakqciXEng8IU0nxx7SUarv
61GBJHVoGFpwOWXdgt2uxyXFbn6nMrhf33ynB+RRAZhqlrC8FROj8Iz+3EoKSAHc
fMJSw6jgdjMCfTDvi0j/eemoNC4fm0eP17Dz9WcwxtIrJPNFVrxZq+biDnpb49nM
IHsbNrILosw9AbHr3C0kTU9tp+Jie2cE1RWHqTIN3S3zb4qN+fIJiU6o6LMhsNP5
+ZxL4M5IYmvZYbU3a+A00TPwVRqBbsZB+et9RtYZsdpepovDiN4XcixEoT7ffqrt
VLjJyoX7Aqmds46lMdsdD3bpPkREmMdf8aMm5fvdIqwbJi1pFMMGMdTgN2WLG5aM
r0bj/DizxL7Brs8RHwOScUgXteZs3gg87v5Ns/3zAyJZvE4norPAiT+EJeXylpRO
LDqqaypFs75nU+mWLNo8Fzck4Xue55SBqx5Bo3aD/Smk8B6r4KMqnMKVsV5RFHAU
XfWb49HulUwHHdn5DAPx
=1vE4
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This branch contains code cleanups, moves and removals for 3.12.
There's a large number of various cleanups, and a nice net removal of
13500 lines of code.
Highlights worth mentioning are:
- A series of patches from Stephen Boyd removing the ARM local timer
API.
- Move of Qualcomm MSM IOMMU code to drivers/iommu.
- Samsung PWM driver cleanups from Tomasz Figa, removing legacy PWM
driver and switching over to the drivers/pwm one.
- Removal of some unusued auto-generated headers for OMAP2+ (PRM/CM).
There's also a move of a header file out of include/linux/i2c/ to
platform_data, where it really belongs. It touches mostly ARM
platform code for include changes so we took it through our tree"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: OMAP2+: Add back the define for AM33XX_RST_GLOBAL_WARM_SW_MASK
gpio: (gpio-pca953x) move header to linux/platform_data/
arm: zynq: hotplug: Remove unreachable code
ARM: SAMSUNG: Remove unnecessary exynos4_default_sdhci*()
tegra: simplify use of devm_ioremap_resource
ARM: SAMSUNG: Remove plat/regs-timer.h header
ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
ARM: SAMSUNG: Remove pwm-clock infrastructure
ARM: SAMSUNG: Remove old PWM timer platform devices
pwm: Remove superseded pwm-samsung-legacy driver
ARM: SAMSUNG: Modify board files to use new PWM platform device
ARM: SAMSUNG: Rework private data handling in dev-backlight
pwm: Add new pwm-samsung driver
ARM: mach-mvebu: remove redundant DT parsing and validation
ARM: msm: Only compile io.c on platforms that use it
iommu/msm: Move mach includes to iommu directory
ARM: msm: Remove devices-iommu.c
ARM: msm: Move mach/board.h contents to common.h
ARM: msm: Migrate msm_timer to CLOCKSOURCE_OF_DECLARE
ARM: msm: Remove TMR and TMR0 static mappings
...
This patch moves the pca953x.h header from include/linux/i2c to
include/linux/platform_data and updates existing support accordingly.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that the sdma driver holds the address tables for i.MX25/5 they
are no longer needed in platform_data. Remove them.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The CLKO is widely used by imx6q board designs to clock audio codec.
Since most codecs accept 24 MHz frequency, let's initially set up CLKO
with OSC24M (cko <-- cko2 <-- osc). Then those board specific CLKO
setup for audio codec can be removed.
The board dts files also need an update on cko reference in codec node.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add defines for common Micrel PHY setups so that other platforms
can use them. Update imx61 and sama5 hardware to use the micrel_phy.h
PHY defines.
Also add support for the KSZ9021RLRN PHY.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: David S. Miller <davem@davemloft.net>
CC: Andrew Victor <linux@maxim.org.za>
CC: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Move anatop related (For USB) from board file to anatop driver
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Current imx53_pm_init() implementation is incomplete as it lacks calling
suspend_set_ops().
Use a single imx5_pm_init() function to handle both mx51 and mx53.
This allows mx53 to enter in low-power mode.
Tested on a mx53qsb:
root@freescale /$ echo mem > /sys/power/state
PM: Syncing filesystems ... done.
mmc0: card e624 removed
Freezing user space processes ... (elapsed 0.001 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
... (Press Power button)
PM: suspend of devices complete after 17.067 msecs
PM: suspend devices took 0.020 seconds
PM: late suspend of devices complete after 0.954 msecs
PM: noirq suspend of devices complete after 1.288 msecs
Disabling non-boot CPUs ...
PM: noirq resume of devices complete after 0.680 msecs
PM: early resume of devices complete after 0.914 msecs
PM: resume of devices complete after 44.955 msecs
PM: resume devices took 0.050 seconds
Restarting tasks ... done.
mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new SDHC card at address e624
mmcblk0: mmc0:e624 SU04G 3.69 GiB
mmcblk0: p1 p2 p3
libphy: 63fec000.etherne:00 - Link is Down
libphy: 63fec000.etherne:00 - Link is Up - 100/Full
root@freescale /$
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Instead of selecting ARM_CPU_SUSPEND only for mx6, we can select it for
all SoCs from the ARCH_MXC family.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The clock output on imx6q CCM_CLKO1 pad is not always cko1 clock, and
there is a multiplexer to select between cko1 and cko2. Add this
missing selection as the clock cko.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Now that the cpu device registration initialises the of_node(if available)
appropriately for all the cpus, parsing here is redundant.
This patch removes all DT parsing and uses cpu->of_node instead.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Add a CLK_SET_RATE_NO_REPARENT clock flag, which will prevent muxes
being reparented during clk_set_rate.
To avoid breaking existing platforms, all callers of clk_register_mux()
are adjusted to pass the new flag. Platform maintainers are encouraged
to remove the flag if they wish to allow mux reparenting on set_rate.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Chao Xie <xiechao.mail@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: "Emilio López" <emilio@elopez.com.ar>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Andrew Chew <achew@nvidia.com>
Cc: Doug Anderson <dianders@chromium.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: spear-devel@list.st.com
Cc: linux-tegra@vger.kernel.org
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com> [tegra]
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [sunxi]
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com> [Zynq]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
There are two improvements for this commit:
- Add comparing pll lock condition after while loop. It can
fix potential fake timeout problem caused by the code is just
scheduled out before compare the timeout, and the time of
scheduling out are more than one jiffies.
- Move timeout assignment more close to compare the timeout.
It can reduce the possibility the code is scheduled out, and
the timeout can be more precise.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
All the clocks controlled by the register 'CCM Serial Clock
Multiplexer Register 1' should be fixup clocks. This patch
changes those clocks from basic multiplexer or divider clocks
to fixup clocks.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
One register may have several fields to control some clocks. It
is possible that the read/write values of some fields may map to
different real functional values, so writing to the other fields
in the same register may break a working clock tree. A real case
is the aclk_podf field in the register 'CCM Serial Clock Multiplexer
Register 1' of i.MX6Q/SDL SoC. This patch introduces a fixup hook
for multiplexer clock which is called before writing a value to
clock registers to support this kind of multiplexer clocks.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
One register may have several fields to control some clocks. It
is possible that the read/write values of some fields may map to
different real functional values, so writing to the other fields
in the same register may break a working clock tree. A real case
is the aclk_podf field in the register 'CCM Serial Clock Multiplexer
Register 1' of i.MX6Q/SDL SoC. This patch introduces a fixup hook
for divider clock which is called before writing a value to clock
registers to support this kind of divider clocks.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Select MIGHT_HAVE_CACHE_L2X0 for armv6 and armv7 i.MX SoCs.
By selecting MIGHT_HAVE_CACHE_L2X0, the user still has the possibility to
disable CACHE_L2X0 selection via menuconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This fixes the following compilation error:
arch/arm/mach-imx/system.c:101:123: error: static declaration of ‘imx_init_l2cache’ follows non-static declaration
In file included from arch/arm/mach-imx/system.c:32:0:
arch/arm/mach-imx/common.h:165:13: note: previous declaration of ‘imx_init_l2cache’ was here
arch/arm/mach-imx/system.c:101:123: warning: ‘imx_init_l2cache’ defined but not used [-Wunused-function]
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The optimized L2 prefect and power setting done in imx_init_l2cache()
can also benefit imx6sl, so let's call the function on imx6sl as well.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
Move imx6q L2 initialization function imx6q_init_l2cache() into
system.c, and rename it imx_init_l2cache(), so that other platforms
other than imx6q can also use the function.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
i.MX6S/DL have the Video PLL post dividers fixed already in revision 1.0
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The KSZ9031 is used on the i.MX6 based Data Modul eDM-QMX6
board. It needs the same fixup to the rx/tx delays as other
i.MX6 boards.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The AR8031 is used on the i.MX6 based sabreSD, sabreauto and wandboard.
All need the same fixup, so add it for all i.MX6.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
In current U-Boot the sabrelite, nitrogen6x and titanium all need
the same fixup for the ksz9021 phy. Instead of limiting the fixup
to a single board apply them for all.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
series involve following modifications:
1) fixing up few things in samsung_pwm_timer clocksource driver,
2) moving remaining Samsung platforms to the new clocksource driver,
3) removing old clocksource driver,
4) adding new multiplatform- and DT-aware PWM driver,
5) moving all Samsung platforms to use the new PWM driver,
6) removing old PWM driver,
7) removing all PWM-related code that is not used anymore.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)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=xmmW
-----END PGP SIGNATURE-----
Merge tag 'v3.12-pwm-cleanup-for-olof' of git://github.com/tom3q/linux into next/cleanup
From Tomasz Figa:
Here is the Samsung PWM cleanup series. Particular patches of the series
involve following modifications:
- fixing up few things in samsung_pwm_timer clocksource driver,
- moving remaining Samsung platforms to the new clocksource driver,
- removing old clocksource driver,
- adding new multiplatform- and DT-aware PWM driver,
- moving all Samsung platforms to use the new PWM driver,
- removing old PWM driver,
- removing all PWM-related code that is not used anymore.
* tag 'v3.12-pwm-cleanup-for-olof' of git://github.com/tom3q/linux: (684 commits)
ARM: SAMSUNG: Remove plat/regs-timer.h header
ARM: SAMSUNG: Remove remaining uses of plat/regs-timer.h header
ARM: SAMSUNG: Remove pwm-clock infrastructure
ARM: SAMSUNG: Remove old PWM timer platform devices
pwm: Remove superseded pwm-samsung-legacy driver
ARM: SAMSUNG: Modify board files to use new PWM platform device
ARM: SAMSUNG: Rework private data handling in dev-backlight
pwm: Add new pwm-samsung driver
pwm: samsung: Rename to pwm-samsung-legacy
ARM: SAMSUNG: Remove unused PWM timer IRQ chip code
ARM: SAMSUNG: Remove old samsung-time driver
ARM: SAMSUNG: Move all platforms to new clocksource driver
ARM: SAMSUNG: Set PWM platform data
ARM: SAMSUNG: Add new PWM platform device
ARM: SAMSUNG: Unify base address definitions of timer block
clocksource: samsung_pwm_timer: Handle suspend/resume correctly
clocksource: samsung_pwm_timer: Do not use clocksource_mmio
clocksource: samsung_pwm_timer: Cache clocksource register address
clocksource: samsung_pwm_timer: Correct definition of AUTORELOAD bit
clocksource: samsung_pwm_timer: Do not request PWM mem region
+ v3.11-rc4
Conflicts:
arch/arm/Kconfig.debug
Signed-off-by: Olof Johansson <olof@lixom.net>
I mis-resolved a merge conflict due to the branch being a bit on the old side,
Stephen noticed. Here's the fix.
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
timer API entirely. Doing so will reduce code in ARM core, reduce the
architecture dependencies of our timer drivers, and simplify the code because
we no longer go through an architecture layer that is essentially a hotplug
notifier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=wZbm
-----END PGP SIGNATURE-----
Merge tag 'remove-local-timers' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm into next/cleanup
From Stephen Boyd:
Now that we have a generic arch hook for broadcast we can remove the
local timer API entirely. Doing so will reduce code in ARM core, reduce
the architecture dependencies of our timer drivers, and simplify the code
because we no longer go through an architecture layer that is essentially
a hotplug notifier.
* tag 'remove-local-timers' of git://git.kernel.org/pub/scm/linux/kernel/git/davidb/linux-msm:
ARM: smp: Remove local timer API
clocksource: time-armada-370-xp: Divorce from local timer API
clocksource: time-armada-370-xp: Fix sparse warning
ARM: msm: Divorce msm_timer from local timer API
ARM: PRIMA2: Divorce timer-marco from local timer API
ARM: EXYNOS4: Divorce mct from local timer API
ARM: OMAP2+: Divorce from local timer API
ARM: smp_twd: Divorce smp_twd from local timer API
ARM: smp: Remove duplicate dummy timer implementation
Resolved a large number of conflicts due to __cpuinit cleanups, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
* A few device tree source fixes regarding pinctrl, clock, and pwm
backlight.
* Fixes imx28 and imx51 audio driver failure caused by sgtl5000 codec
driver change by supplying the correct clock for codec.
* imx6q emi_sel clock muxing and imx6q-iomuxc-gpr macro fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJR5B55AAoJEFBXWFqHsHzOEGoH/2DesLDZkQbUCn+w7Z3H7HYi
QAPeG1F/Ke3cBSaT+v/Z+46MgmU2gyQkxk08GRtPuVAZwCuWxSUN1H6+yakeBdHb
XGXR25RbbASIpYdYnC37eKiU2itiBmD7CRbWJ5xPHEluAgr47vr3OKfls6laii3b
nSM4sKz45PxBJ55M0qcE+A6oVdf9c+G0vm0aX14xEiLEUghB/U0KNKWp+B63hwfh
tg11gNwr2dO8jv51xpwJXH17juoZ46srOzmxERJm3j08JSz/tJSvIQajSsg54aLT
pAxToPAeuGGga5+7AanGT+repzZdd74Lp3U/lGw6WpaxLOpFf5Am3841O8qqCLw=
=q0LM
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo, imx fixes for 3.11:
- A few device tree source fixes regarding pinctrl, clock, and pwm
backlight.
- Fixes imx28 and imx51 audio driver failure caused by sgtl5000 codec
driver change by supplying the correct clock for codec.
- imx6q emi_sel clock muxing and imx6q-iomuxc-gpr macro fixes
* tag 'imx-fixes-3.11' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx51-babbage: Pass a real clock to the codec
ARM i.MX53: mba53: Fix PWM backlight DT node
ARM: imx: fix vf610 enet module clock selection
ARM: mxs: saif0 is the clock provider to sgtl5000
ARM: i.MX6Q: correct emi_sel clock muxing
ARM i.MX6Q: Fix IOMUXC GPR1 defines for ENET_CLK_SEL and IPU1/2_MUX
ARM: i.MX27: Typo fix
ARM: imx27: Fix documentation for SPLL clock
ARM i.MX53: Fix UART pad configuration
The fec/enet driver calculates MDC rate with the formula below.
ref_freq / ((MII_SPEED + 1) x 2)
The ref_freq here is the fec internal module clock, which is missing
from clk-vf610 clock driver right now. And clk-vf610 driver mistakenly
supplies RMII clock (50 MHz) as the source to fec. This results in the
situation that fec driver gets ref_freq as 50 MHz, while physically it
runs at 66 MHz (fec module clock physically sources from ipg which runs
at 66 MHz). That's why software expects MDC runs at 2.5 MHz, while the
measurement tells it runs at 3.3 MHz. And this causes the PHY KSZ8041
keeps swithing between Full and Half mode as below.
libphy: 400d0000.etherne:00 - Link is Up - 100/Full
libphy: 400d0000.etherne:00 - Link is Up - 100/Half
libphy: 400d0000.etherne:00 - Link is Up - 100/Full
libphy: 400d0000.etherne:00 - Link is Up - 100/Half
libphy: 400d0000.etherne:00 - Link is Up - 100/Full
libphy: 400d0000.etherne:00 - Link is Up - 100/Half
Add the missing module clock for ENET0 and ENET1, and correct the clock
supplying in device tree to fix above issue.
Thanks to Alison Wang <b18965@freescale.com> for debugging the issue.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The correct muxing for emi_sel clock should be
2b'00 - 396M PFD
2b'01 - PLL3
2b'10 - AXI clk root
2b'11 - 352M PFD
This patch corrects the muxing in the clock driver.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
and are flagged as __cpuinit -- so if we remove the __cpuinit from
the arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
related content into no-ops as early as possible, since that will get
rid of these warnings. In any case, they are temporary and harmless.
This removes all the ARM uses of the __cpuinit macros from C code,
and all __CPUINIT from assembly code. It also had two ".previous"
section statements that were paired off against __CPUINIT
(aka .section ".cpuinit.text") that also get removed here.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a9 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
Preparing to move the parsing of reboot= to generic kernel code forces
the change in reboot_mode handling to use the enum.
[akpm@linux-foundation.org: fix arch/arm/mach-socfpga/socfpga.c]
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull timer core updates from Thomas Gleixner:
"The timer changes contain:
- posix timer code consolidation and fixes for odd corner cases
- sched_clock implementation moved from ARM to core code to avoid
duplication by other architectures
- alarm timer updates
- clocksource and clockevents unregistration facilities
- clocksource/events support for new hardware
- precise nanoseconds RTC readout (Xen feature)
- generic support for Xen suspend/resume oddities
- the usual lot of fixes and cleanups all over the place
The parts which touch other areas (ARM/XEN) have been coordinated with
the relevant maintainers. Though this results in an handful of
trivial to solve merge conflicts, which we preferred over nasty cross
tree merge dependencies.
The patches which have been committed in the last few days are bug
fixes plus the posix timer lot. The latter was in akpms queue and
next for quite some time; they just got forgotten and Frederic
collected them last minute."
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
hrtimer: Remove unused variable
hrtimers: Move SMP function call to thread context
clocksource: Reselect clocksource when watchdog validated high-res capability
posix-cpu-timers: don't account cpu timer after stopped thread runtime accounting
posix_timers: fix racy timer delta caching on task exit
posix-timers: correctly get dying task time sample in posix_cpu_timer_schedule()
selftests: add basic posix timers selftests
posix_cpu_timers: consolidate expired timers check
posix_cpu_timers: consolidate timer list cleanups
posix_cpu_timer: consolidate expiry time type
tick: Sanitize broadcast control logic
tick: Prevent uncontrolled switch to oneshot mode
tick: Make oneshot broadcast robust vs. CPU offlining
x86: xen: Sync the CMOS RTC as well as the Xen wallclock
x86: xen: Sync the wallclock when the system time is set
timekeeping: Indicate that clock was set in the pvclock gtod notifier
timekeeping: Pass flags instead of multiple bools to timekeeping_update()
xen: Remove clock_was_set() call in the resume path
hrtimers: Support resuming with two or more CPUs online (but stopped)
timer: Fix jiffies wrap behavior of round_jiffies_common()
...
git://git.kernel.org/pub/scm/linux/kernel/git/frederic/linux-dynticks into timers/core
Frederic sayed: "Most of these patches have been hanging around for
several month now, in -mmotm for a significant chunk. They already
missed a few releases."
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull LED subsystem updates from Bryan Wu:
- lp55xx device tree updates
- mc13xxx driver updates
- some clean up
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: mc13783: Fix "uninitialized variable" warning
leds: Convert led class driver from legacy pm ops to dev_pm_ops
leds: leds-mc13783: Add MC13892 LED support
leds: leds-mc13783: Prepare driver to support MC13892 LEDs
leds: renesas-tpu: cleanup a small type issue
leds: use platform_{get,set}_drvdata()
leds: leds-gpio: Let device core handle pinctrl
leds: lp5562: Properly setup of_device_id table
leds: lp5523: Properly setup of_device_id table
leds: lp5521: Properly setup of_device_id table
leds: lp5562: support the device tree feature
leds: lp55xx: support dynamic channel settings in the device tree structure
leds: leds-ns2: remove unnecessary platform_set_drvdata()
leds: leds-mc13783: remove unnecessary platform_set_drvdata()
leds: leds-gpio: remove unnecessary platform_set_drvdata()
leds: atmel-pwm: remove unnecessary platform_set_drvdata()
leds: lp55xx: add support for Device Tree bindings
Pull ARM updates from Russell King:
"This contains the usual updates from other people (listed below) and
the usual random muddle of miscellaneous ARM updates which cover some
low priority bug fixes and performance improvements.
I've started to put the pull request wording into the merge commits,
which are:
- NoMMU stuff:
This includes the following series sent earlier to the list:
- nommu-fixes
- R7 Support
- MPU support
I've left out the ARCH_MULTIPLATFORM/!MMU stuff that Arnd and I
were discussing today until we've reached a conclusion/that's had
some more review.
This is rebased (and re-tested) on your devel-stable branch because
otherwise there were going to be conflicts with Uwe's V7M work now
that you've merged that. I've included the fix for limiting MPU to
CPU_V7.
- Huge page support
These changes bring both HugeTLB support and Transparent HugePage
(THP) support to ARM. Only long descriptors (LPAE) are supported
in this series.
The code has been tested on an Arndale board (Exynos 5250).
- LPAE updates
Please pull these miscellaneous LPAE fixes I've been collecting for
a while now for 3.11. They've been tested and reviewed by quite a
few people, and most of the patches are pretty trivial. -- Will Deacon.
- arch_timer cleanups
Please pull these arch_timer cleanups I've been holding onto for a
while. They're the same as my last posting, but have been rebased
to v3.10-rc3.
- mpidr linearisation (multiprocessor id register - identifies which
CPU number we are in the system)
This patch series that implements MPIDR linearization through a
simple hashing algorithm and updates current cpu_{suspend}/{resume}
code to use the newly created hash structures to retrieve context
pointers. It represents a stepping stone for the implementation of
power management code on forthcoming multi-cluster ARM systems.
It has been tested on TC2 (dual cluster A15xA7 system), iMX6q,
OMAP4 and Tegra, with processors hitting low-power states requiring
warm-boot resume through the cpu_resume code path"
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (77 commits)
ARM: 7775/1: mm: Remove do_sect_fault from LPAE code
ARM: 7777/1: Avoid extra calls to the C compiler
ARM: 7774/1: Fix dtb dependency to use order-only prerequisites
ARM: 7770/1: remove residual ARMv2 support from decompressor
ARM: 7769/1: Cortex-A15: fix erratum 798181 implementation
ARM: 7768/1: prevent risks of out-of-bound access in ASID allocator
ARM: 7767/1: let the ASID allocator handle suspended animation
ARM: 7766/1: versatile: don't mark pen as __INIT
ARM: 7765/1: perf: Record the user-mode PC in the call chain.
ARM: 7735/2: Preserve the user r/w register TPIDRURW on context switch and fork
ARM: kernel: implement stack pointer save array through MPIDR hashing
ARM: kernel: build MPIDR hash function data structure
ARM: mpu: Ensure that MPU depends on CPU_V7
ARM: mpu: protect the vectors page with an MPU region
ARM: mpu: Allow enabling of the MPU via kconfig
ARM: 7758/1: introduce config HAS_BANDGAP
ARM: 7757/1: mm: don't flush icache in switch_mm with hardware broadcasting
ARM: 7751/1: zImage: don't overwrite ourself with a page table
ARM: 7749/1: spinlock: retry trylock operation if strex fails on free lock
ARM: 7748/1: oabi: handle faults when loading swi instruction from userspace
...
These changes from 30 individual branches for the most part update device
tree files, but there are also a few source code changes that have crept
in this time, usually in order to atomically move over a driver from
using hardcoded data to DT probing.
A number of platforms change their DT files to use the C preprocessor,
which is causing a bit of churn, but that is hopefully only this once.
There are a few conflicts with the other branches unfortunately:
* in exynos5440.dtsi and kirkwood-6281.dtsi, device nodes are added
from multiple branches. Need to be careful to have the right
set of closing braces as git gets this one wrong.
* In kirkwood.dtsi, one 'ranges' line got split into two lines, while
another line got added. Order of the lines does not matter.
* in sama5d3.dtsi, some cleanup was merged the wrong way, causing
a bogus conflict. We want the 'dmas' and 'dma-names' properties
to get added here.
* Two lines got removed independently in arch/arm/mach-mxs/mach-mxs.c
* Contents get added independently in arch/arm/mach-omap2/cclock33xx_data.c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=8PtJ
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"These changes from 30 individual branches for the most part update
device tree files, but there are also a few source code changes that
have crept in this time, usually in order to atomically move over a
driver from using hardcoded data to DT probing.
A number of platforms change their DT files to use the C preprocessor,
which is causing a bit of churn, but that is hopefully only this once"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (372 commits)
ARM: at91: dt: rm9200ek: add spi support
ARM: at91: dt: rm9200: add spi support
ARM: at91/DT: at91sam9n12: add SPI DMA client infos
ARM: at91/DT: sama5d3: add SPI DMA client infos
ARM: at91/DT: fix SPI compatibility string
ARM: Kirkwood: Fix the internal register ranges translation
ARM: dts: bcm281xx: change comment to C89 style
ARM: mmc: bcm281xx SDHCI driver (dt mods)
ARM: nomadik: add the new clocks to the device tree
clk: nomadik: implement the Nomadik clocks properly
ARM: dts: omap5-uevm: Provide USB Host PHY clock frequency
ARM: dts: omap4-panda: Fix DVI EDID reads
ARM: dts: omap4-panda: Add USB Host support
arm: mvebu: enable mini-PCIe connectors on Armada 370 RD
ARM: shmobile: irqpin: add a DT property to enable masking on parent
ARM: dts: AM43x EPOS EVM support
ARM: dts: OMAP5: Add bandgap DT entry
ARM: dts: AM33XX: Add pinmux configuration for CPSW to am335x EVM
ARM: dts: AM33XX: Add pinmux configuration for CPSW to EVMsk
ARM: dts: AM33XX: Add pinmux configuration for CPSW to beaglebone
...
As there are no imx in-tree users of flexcan_platform_data, this patch removes
the possibility to register a flexcan device with platform data.
The functionality to swith on/off CAN transceivers is added to DT via
regulators in a later patch.
Compile time tested with imx_v4_v5_defconfig and imx_v6_v7_defconfig.
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Separate the smp_twd timers from the local timer API. This will
allow us to remove ARM local timer support in the near future and
gets us closer to moving this driver to drivers/clocksource.
Tested-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This is required for building a kernel that enables only
IMX6SL but not IMX6Q, which would get a build error when
syscon is not available.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
This is required for building a kernel that enables only
scb9328 and would not get the i.MX1 specific files
otherwise.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sascha Hauer <kernel@pengutronix.de>
This patch rewrite driver code to be ready to add support for
MC13892 LEDs and probe from devicetree.
(cooloney@gmail.com: fix one coding style issue when apply this patch)
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Tested-by: Philippe Retornaz <philippe.retornaz@epfl.ch>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
With device tree clk lookup support in place, we can move audio codec
clk lookup for ssi_ext1 into device tree now, so that imx53_qsb_init()
can be saved.
Since ssi_ext2 lookup is used nowhere, it gets removed together with
ssi_ext1 lookup from clk driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
WM8962 needs 24MHz clock for its MCLK, so choose PLL4 as the parent of clko1.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
There are ulpi access ops implemented in drivers/usb/phy/phy-ulpi.c.
mxc access ops implement the same access operations within mach-imx. This
patch removes the mxc ulpi file and uses phy-ulpi instead for
imx_otg_ulpi_create.
phy-ulpi successfully tested with i.MX27 Phytec phyCARD-S (pca100).
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Shawn Guo