We want the size of the struct, not of a pointer to it. To be future
proof, just dereference the pointer to get the desired type.
Fixes: dd1aa2524b ("i2c: brcmstb: Add Broadcom settop SoC i2c controller driver")
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Starting from Intel Sunrisepoint (Skylake PCH) the iTCO watchdog
resources have been moved to reside under the i801 SMBus host
controller whereas previously they were under the LPC device.
This patch adds Intel lewisburg SMBus support for iTCO device.
It allows to load watchdog dynamically when the hardware is
present.
Fixes: cdc5a3110e ("i2c: i801: add Intel Lewisburg device IDs")
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Commit 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind") introduced pm_runtime_reinit() that is used
to reinitialize PM runtime after -EPROBE_DEFER. This allows shutting
down the device after a failed probe.
However, for drivers using pm_runtime_use_autosuspend() this can cause
a state where suspend callback is never called after -EPROBE_DEFER.
On the following device driver probe, hardware state is different from
the PM runtime state causing omap_device to produce the following
error:
omap_device_enable() called from invalid state 1
And with omap_device and omap hardware being picky for PM, this will
block any deeper idle states in hardware.
The solution is to fix the drivers to follow the PM runtime documentation:
1. For sections of code that needs the device disabled, use
pm_runtime_put_sync_suspend() if pm_runtime_set_autosuspend() has
been set.
2. For driver exit code, use pm_runtime_dont_use_autosuspend() before
pm_runtime_put_sync() if pm_runtime_use_autosuspend() has been
set.
Fixes: 5de85b9d57 ("PM / runtime: Re-init runtime PM states at probe
error and driver unbind")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The I2C bus names are supposed to be stable as they can be used by
userspace to uniquely identify a specific I2C bus. So restore the
original names for all legacy (pre-SB800) devices.
For SB800 devices and later, improve the names. "SDA" refers to the
serial data pin of each SMBus port, it's an implementation detail the
user doesn't need to know. Use "port" instead, which is easier to
understand.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Christian Fetzer <fetzer.ch@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is effectively reapplies the commit b0898fdaff ("i2c: designware-pci: use
IRQF_COND_SUSPEND flag") after the commit d80d134182 ("i2c: designware: Move
common probe code into i2c_dw_probe()"). Original message as follows.
The mentioned flag fixes a warning on Intel Edison board since one of the I2C
controller shares IRQ line with watchdog timer.
Fixes: d80d134182 (i2c: designware: Move common probe code into i2c_dw_probe())
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This closes a race window where I2C device drivers attempt to access
I2C buses which aren't fully initialized yet.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Christian Fetzer <fetzer.ch@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We need a single mutex for all 4 shared SMBus ports on the SB800. A
per-port mutex doesn't protect us from concurrent access.
In theory the mutex should be per PCI device, however in practice we
know that there's only ever a single instance of the device in a given
system so we can use a global.
Also take the mutex during initialization, as first port may be already
in use when second port is initialized.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Christian Fetzer <fetzer.ch@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[wsa: made mutex static]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Pull i2c updates from Wolfram Sang:
"Quite some driver updates:
- piix4 can now handle multiplexed adapters
- brcmstb, xlr, eg20t, designware drivers support more SoCs
- emev2 gained i2c slave support
- img-scb and rcar got bigger refactoring to remove issues
- lots of common driver updates
i2c core changes:
- new quirk flag when an adapter does not support clock stretching,
so clients can be configured to avoid that if possible
- added a helper function to retrieve timing parameters from firmware
(with rcar being the first user)
- "multi-master" DT binding added so drivers can adapt to this
setting (like disabling PM to keep arbitration working)
- RuntimePM for the logical adapter device is now always enabled by
the core to ensure propagation from childs to the parent (the HW
device)
- new macro builtin_i2c_driver to reduce boilerplate"
* 'i2c/for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (70 commits)
i2c: create builtin_i2c_driver to avoid registration boilerplate
i2c: imx: fix i2c resource leak with dma transfer
dt-bindings: i2c: eeprom: add another EEPROM device
dt-bindings: move I2C eeprom descriptions to the proper file
i2c: designware: Do not require clock when SSCN and FFCN are provided
DT: i2c: trivial-devices: Add Epson RX8010 and MPL3115
i2c: s3c2410: remove superfluous runtime PM calls
i2c: always enable RuntimePM for the adapter device
i2c: designware: retry transfer on transient failure
i2c: ibm_iic: rename i2c_timings struct due to clash with generic version
i2c: designware: Add support for AMD Seattle I2C
i2c: imx: Remove unneeded comments
i2c: st: use to_platform_device()
i2c: designware: use to_pci_dev()
i2c: brcmstb: Adding support for CM and DSL SoCs
i2c: mediatek: fix i2c multi transfer issue in high speed mode
i2c: imx: improve code readability
i2c: imx: Improve message log when DMA is not used
i2c: imx: add runtime pm support to improve the performance
i2c: imx: init bus recovery info before adding i2c adapter
...
* acpi-soc:
PM / clk: don't leave clocks enabled when driver not bound
i2c: dw: Add APM X-Gene ACPI I2C device support
ACPI / APD: Add APM X-Gene ACPI I2C device support
ACPI / LPSS: change 'does not have' to 'has' in comment
Revert "dmaengine: dw: platform: provide platform data for Intel"
dmaengine: dw: return immediately from IRQ when DMA isn't in use
dmaengine: dw: platform: power on device on shutdown
ACPI / LPSS: override power state for LPSS DMA device
ACPI / LPSS: power on when probe() and otherwise when remove()
ACPI / LPSS: do delay for all LPSS devices when D3->D0
ACPI / LPSS: allow to use specific PM domain during ->probe()
Revert "ACPI / LPSS: allow to use specific PM domain during ->probe()"
device core: add BUS_NOTIFY_DRIVER_NOT_BOUND notification
x86/platform/iosf_mbi: Remove duplicate definitions
Conflicts:
drivers/i2c/busses/i2c-designware-platdrv.c
* device-properties:
device property: avoid allocations of 0 length
device property: the secondary fwnode needs to depend on the primary
device property: add spaces to PROPERTY_ENTRY_STRING macro
include/linux/property.h: fix build issues with gcc-4.4.4
i2c: designware: Convert to use unified device property API
mfd: intel-lpss: Pass HSUART configuration via properties
mfd: intel-lpss: Pass SDA hold time to I2C host controller driver
mfd: intel-lpss: Add support for passing device properties
mfd: core: propagate device properties to sub devices drivers
driver core: Do not overwrite secondary fwnode with NULL if it is set
driver core: platform: Add support for built-in device properties
device property: Take a copy of the property set
device property: Fallback to secondary fwnode if primary misses the property
device property: return -EINVAL when property isn't found in ACPI
device property: improve readability of macros
device property: helper macros for property entry creation
device property: keep single value inplace
device property: refactor built-in properties support
device property: rename helper functions
device property: always check for fwnode type
In i2c_imx_dma_xfer(), when dmaengine_submit() returns error,
the context goto label err_submit and then return. However, the
memory allocated for txdesc has not been freed yet, which
leads to resource leak.
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The current driver uses input clock source frequency to calculate
values for [SS|FS]_[HC|LC] registers. However, when booting ACPI, we do not
currently have a good way to provide the frequency information.
Instead, we can leverage the SSCN and FFCN ACPI methods, which can be used
to directly provide these values. So, the clock information should
no longer be required during probing.
However, since clk can be invalid, additional checks must be done where
we are making use of it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Tested-by: Loc Ho <lho@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
RuntimePM of the adapter device is now taken care of by the core. So, we
can remove these calls.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The adapter device is a logical device. Because of that, it already uses
pm_runtime_no_callbacks() in the core. To ensure proper propagation from
the children (i2c devices) to the parent of the adapter (the HW device),
make sure RuntimePM is enabled in any case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Set the i2c_adapter retries field to a sensible value. This allows the i2c core
to retry master_xfer() when it returns -EAGAIN. Currently the i2c-designware
driver returns -EAGAIN only on Tx arbitration failure (DW_IC_TX_ARB_LOST).
Reported-by: Rolland Chau <zourongrong@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable APM X-Gene ACPI I2C device support by adding the
corresponding ACPI ID. The platform ACPI APD corresponding
change is required to provide the proper clock frequency input.
Signed-off-by: Loc Ho <lho@apm.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixes: e1dba01ca6 ("i2c: add generic routine to parse DT for timing information")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add device HID AMDI0510 to match the I2C controlers on AMD Seattle platform
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
These multi-lines comments do not follow the standard kernel coding
style. In fact, they are not useful comments, so get rid of them.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use to_pci_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Broadcoms DSL, CM (cable modem)and STB I2C core implementation have
8 data in/out registers that can transfer 8 bytes or 32 bytes max.
Cable and DSL "Peripheral" i2c cores use single byte per data
register and the STB can use 4 byte per data register transfer.
Adding support to take care of this difference. Accordingly added
the compatible string for SoCs using the "Peripheral" I2C block.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For mt8173 platform with auto restart support, when doing i2c multi
transfer in high speed, we should ignore the first restart irq after
the master code, otherwise the first transfer will be discarded.
Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Reviewed-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Replace of_get_named_gpio_flags with of_get_named_gpio because
the latter has less parameters, which improves code readability.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When DMA cannot be used, it is better to state that the I2C controller
will operate in PIO mode.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In our former i2c driver, i2c clk is enabled and disabled in
xfer function, which contributes to power saving. However,
the clk enable process brings a busy wait delay until the core
is stable. As a result, the performance is sacrificed.
To weigh the power consumption and i2c bus performance, runtime
pm is the good solution for it. The clk is enabled when a i2c
transfer starts, and disabled after a specifically defined delay.
If CONFIG_PM is disabled the net result of this patch is that the
clock is never disabled.
Without the patch the test case (many eeprom reads) executes with approx:
real 1m7.735s
user 0m0.488s
sys 0m20.040s
With the patch the same test case (many eeprom reads) executes with approx:
real 0m54.241s
user 0m0.440s
sys 0m5.920s
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Gao Pan <b54642@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[wsa: sorted includes]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
During driver probe, i2c_imx_init_recovery_info() must come before
i2c_add_numbered_adapter(), because the get/set_scl() functions
are assigned in i2c_register_adapter() under the conditon that bus
recover_info are initialized. Otherwise, get/set_scl() function
pointers never get assigned.
In such case, when i2c_generic_gpio_recovery() is used for bus recovery,
there will be kernel crash because bri->set_scl is NULL.
The solution to this bug is moving i2c_imx_init_recovery_info() before
i2c_register_adapter().
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
In multi master mode, the IP core needs to be always active for
arbitration reasons. Get the config from DT and set up PM depending on
the config.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
These macros don't really hide complexity, but C idioms. Removing them
makes the code easier to read IMO and make a planned extension easier.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In version 3.3 of the IP when transaction halt is set, an interrupt
will be generated after each byte of a transfer instead of after
every transfer but before the stop bit.
Due to this behaviour we have to be careful that every time we
release the transaction halt we have to re-enable it straight away
so that we only process a single byte, not doing so will result in
all remaining bytes been processed and a stop bit being issued,
which will prevent us having a repeated start.
This change will have no effect on earlier versions of the IP.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Master halt is issued after each byte of a transaction is processed in
IP version 3.3.
Master halt will stall the bus by holding the SCK line low until the
halt bit in the scb_general_control is cleared.
After the last byte of a transfer is processed we can use the Master
Halt interrupt to facilitate a repeated start transfer without
issuing a stop bit.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Stop Detected interrupt is triggered when a Stop bit is detected on
the bus, which indicates the end of the current transfer.
When the end of a transfer is indicated by the Stop Detected interrupt,
drain the FIFO and signal completion for the transaction.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Now that we are using the transaction halt interrupt to safely control
repeated start transfers, we no longer need to handle the fifo
emptying interrupts.
Handling this interrupt along with Transaction Halt interrupt can
cause erratic behaviour.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This commit adds support for the I2C_M_IGNORE_NAK protocol
modification.
Such behaviour can only be implemented in atomic mode. So, if a
transaction contains a message with such flag the drivers
switches to atomic mode. The implementation consists simply in
treating NAKs as ACKs.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
When we also are I2C slave, we need to disable runtime PM because the
address detection mechanism needs to be active all the time. However, we
can reenable runtime PM once the slave instance was unregistered. So,
use pm_runtime_get_sync/put to achieve this, since it has proper
refcounting. pm_runtime_allow/forbid is like a global knob controllable
from userspace which is unsuitable here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
This function used to be DT only, so it lived inside a CONFIG_OF block.
Now it uses device attributes and must be moved outside of it. No
further code changes, only one whitespace improvement.
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Until we have proper support to make I2C slave support fully optional,
select it to prevent build errors on randconfigs.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Sigma Designs variant of this controller has the ability to generate
interrupts. This is controlled using two additional registers, oddly
enough overlapping with the defined but unused HDSTATIM.
This patch adds support for using this feature instead of busy-looping
if an IRQ is specified.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The BYTECNT register holds the transfer size minus one. Setting it to
the correct value removes the need for a dummy read/write at the end of
each transfer. As zero-length transfers are not supported, do not
advertise I2C_FUNC_SMBUS_QUICK.
In other words, this patch makes the driver transfer the number of bytes
requested unless this is zero, which is not supported by the hardware
and is thus refused.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Sigma Designs chips use a variant of this controller with the following
differences:
- The BUSY bit in the STATUS register is inverted
- Bit 8 of the CONFIG register must be set
- The controller can generate interrupts
This patch adds support for the first two of these. It also calculates
and sets the correct clock divisor if a clk is provided. The bus
frequency is optionally speficied in the device tree node.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is code to divide by "bus_speed" some lines below.
To eliminate the possibility of division by zero, bail out if
"clock-frequency" is specified as zero.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This input clock is used to generate the sampling clock for I2C bus.
If the clock rate is zero, there is something wrong with the clock
driver. Bail out with the appropriate error message in such a case.
It would make it easier to find the root cause of failure.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is code to divide by "bus_speed" some lines below.
To eliminate the possibility of division by zero, bail out if
"clock-frequency" is specified as zero.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This input clock is used to generate the sampling clock for I2C bus.
If the clock rate is zero, there is something wrong with the clock
driver. Bail out with the appropriate error message in such a case.
It would make it easier to find the root cause of failure.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Switch to the new generic functions. Plain convert, no functionality
added yet.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The probe function is a little bit messy, something here, something
there. Rework it so that there is some order: first init the private
structure, then the adapter, then do HW init. This also allows us to
remove the device argument of the clock calculation function, because it
now can be deduced from the private structure. Also, shorten some lines
where possible. This is a preparation for further refactoring.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Inspired from the i2c-rk3x driver (thanks guys!) but refactored and
extended. See built-in docs for further information.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
On an hardware shared I2C bus (certain Intel Baytrail SoC platforms) the
runtime PM disable depth keeps increasing over repeated modprobe/rmmod
cycle because pm_runtime_disable() is called without checking should it
be disabled already because of bus sharing.
This hasn't made any other harm than dev->power.disable_depth keeps
increasing but keep it sync by calling pm_runtime_disable() only when
runtime PM is not disabled.
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang