The HCI User Channel operation is an admin operation that puts the
device into promiscuous mode for single use. It is more suitable
to require CAP_NET_ADMIN than CAP_NET_RAW.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When enabling or disabling high speed setting it is required to send
a new settings event to inform other management interface users about
the changed settings.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Hiding the Bluetooth high speed support behind a module parameter is
not really useful. This can be enabled and disabled at runtime via
the management interface. This also has the advantage that this can
now be changed per controller and not just global.
This patch removes the module parameter and exposes the high speed
setting of the management interface to all controllers.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The BDADDR_LOCAL is a relict from userspace and has never been used
within the kernel. So remove that constant and replace it with a new
BDADDR_NONE that is similar to HCI_DEV_NONE with all bits set.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The controller type is limited to BR/EDR/LE and AMP controllers. This
can be easily encoded with just 2 bits and still leave enough room
for future controller types.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If allowed in a country, these channels typically require DFS
so mark them as such. Channel 144 is a bit special, it's coming
into use now to allow more VHT 80 channels, but world roaming
with passive scanning is acceptable anyway. It seems fairly
unlikely that it'll be used as the control channel for a VHT
AP, but it needs to be present to allow a full VHT connection
to an AP that uses it as one of the secondary channels.
Also enable VHT 160 on these channels, and also for channels
36-48 to be able to use VHT 160 there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A CAC should fail if it is triggered while the interface is already
running.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the default setting for WMM parameters outside the for loop
to avoid redundant assignment multiple times.
Signed-off-by: Fred Zhou <fred.zy@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices may not be able to report A-MSDUs in
single buffers. Drivers for such devices were
forced to re-assemble A-MSDUs which would then
be eventually disassembled by mac80211. This could
lead to CPU cache thrashing and poor performance.
Since A-MSDU has a single sequence number all
subframes share it. This was in conflict with
retransmission/duplication recovery
(IEEE802.11-2012: 9.3.2.10).
Patch introduces a new flag that is meant to be
set for all individually reported A-MSDU subframes
except the last one. This ensures the
last_seq_ctrl is updated after the last subframe
is processed. If an A-MSDU is actually a duplicate
transmission all reported subframes will be
properly discarded.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
[johannes: add braces that were missing even before]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The authentication frame has a fixied size of 30 bytes
(including header, algo num, trans seq num, and status)
followed by a variable challenge text.
Allocate using exact size, instead of over-allocation
by sizeof(ieee80211_mgmt).
Signed-off-by: Fred Zhou <fred.zy@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for parsing and setting the dfs region (ETSI, FCC, JP)
when the internal regulatory database is used. Before this
the DFS region was being ignored even if present on the used
db.txt
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Reviewed-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can be useful for drivers if they have any failure cases
when joining an IBSS. Also move setting the queue parameters
to before this new call, in case the new driver op needs them
already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
VHT_CAP_BEAMFORMER_ANTENNAS cap is actually defined in the draft as
VHT_CAP_BEAMFORMEE_STS_MAX, and its size is 3 bits long.
VHT_CAP_SOUNDING_DIMENSIONS is also 3 bits long.
Fix the definitions and change the cap masking accordingly.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some debugfs related functions snprintf was used
while scnprintf should have been used instead.
(blindly adding the return value of snprintf and supplying
it to the next snprintf might result in buffer overflow when
the input is too big)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This keeps the kernel happy when using edge-irqs and requesting a
threaded irq.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Extract and print info for the new RDL 5, 6, 7 and 8.
Replace const struct with function which translates
the RDL number to string.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Barak Bercovitz <barak@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
In addition to existing WCS PLL configuration add and enable
also the coex PLL during init phase. This fixes boot failures
due to silicon latchup in high temperature environment (>85c).
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Nadim Zubidat <nadimz@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Channels 52-64 were mapped incorrectly.
Refactor and document wlcore_get_reg_conf_ch_idx() in
order to make it clear what's going on there.
While on it, fix the return value check to consider
0 as a valid return value as well (indicates channel 1).
Reported-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
wlvif could be passed as NULL from the wlcore_tx_work_locked()
to the wl1271_prepare_tx_frame() and to wl1271_skb_queue_head()
functions. This may lead to a Kernel panic, fix this by
validating that wlvif != NULL.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Remove scan debug dumps which are rarely used.
Make scan debug prints more clear and short.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
We need some stuff done on idle change, most notably we have to stop
sched-scanning. Take care of this by reintroducing idle handling.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
We now disable elp sleep during plt mode to allow normal operation of
plt tools such as calibrator.
Having elp_sleep enabled during plt mode is actually not required and
in fact it disrupt plt operations such as rx statistics etc.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Under this mode the chip is powered on including sdio
but no FW is downloaded and run, interrupts are not enabled, etc...
This mode is intended to allow RTTT to bridge sdio as a transport
to the chip.
Driver only provides sdio access using the dev_mem debugfs file.
Some fixes done to the code that ensures that PLT mode and normal
driver power mode (ifconfig/add_interface) are mutually excluded.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Start a ROC on the AP channel beforing sending the authentication reply
to a connecting STA. This ROC is held up to 1 second via a timer. If the
station is authorized and added by mac80211, the ROC is extended until
the station is fully authorized.
We make sure not to ROC twice when several stations are connecting in
parallel and to only release the ROC when both the pending-reply timer
and the STA-state callbacks do not require it.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Fix RT3070 chip RF initial value to be similar to the latest Ralink vendor
driver.
Tested on Asus N13 usb wifi dongle.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the variable continual, and change the while loop
to break when efuse_data == 0xFF.
Tested by compilation only.
CC: Joe Perches <joe@perches.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch brings no functional change.
There are still duplicate macros across the rtlwifi directory, for example
IQK_DELAY_TIME is defined multiple times, sometimes with different values,
this patch only removes duplicates within the same header file.
Signed-off-by: Catalin Iacob <iacobcatalin@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fast antenna diversity is required only for single chain
chips and the diversity initialization is done in the
per-family board setup routines. Enabling of diversity
should be done based on the calibrated EEPROM/OTP data,
doing it for all chips is incorrect.
Remove the code that sets the fast_div bit for all cards, since
the documentation for the AR_PHY_CCK_DETECT register says:
reg 642: sig_detect_cck
enable_ant_fast_div : Only used for single chain chips.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a FATAL interrupt is received, a full chip reset is
required, which is done in the main tasklet. But since
the reset routine is scheduled as a work item, make sure
that interrupts are not enabled in the tasklet before the
reset is done.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rather than using the chip ID to read only chain-0 CCA
registers and avoid reading chain-1, use the RX chainmask
instead. There are some 1-stream PCI devices based on AR9287
such as TL-WN751ND. Improper NF calibration might result in
DMA errors/timeouts.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove routine _rtl92c_process_phyinfo() by using the equivalent routine
in driver rtlwifi.
This change also allows the removal of 5 additional routines from rtl8192cu.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The other structures in wmi.h are already marked this way.
Without this marking, we get an unaliged access panic in the tilegx kernel:
Starting stack dump of tid 0, pid 0 (swapper) on cpu 35 at cycle 198675113844
frame 0: 0xfffffff7103ada90 ath9k_htc_swba+0x120/0x618 [ath9k_htc]
frame 1: 0xfffffff7103a4b10 ath9k_wmi_event_tasklet+0x1b0/0x270 [ath9k_htc]
frame 2: 0xfffffff700326570 tasklet_action+0x148/0x298
[...]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The band selection and PE control code for the
RT3593 chipsets only handles USB based devices
currently. Due to this limitation RT3593 based
PCIe cards are not working correctly.
On PCIe cards band selection is controlled via
GPIO #8 which is identical to the USB devices.
The LNA PE control is slightly different, all
LNA PEs are controlled by GPIO #4.
Update the code to configure the GPIO_CTRL register
correctly on PCIe devices.
Cc: Steven Liu <steven.liu@mediatek.com>
Cc: JasonYS Cheng <jasonys.cheng@mediatek.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since HW PeakDetect calibration is turned on for AR9462,
various conditions have to be handled in the driver:
* Enable agc_cal when loading RTT fails.
* Disable SW PeakDetect calibration when RTT calibration is not enabled.
* Keep SW PeakDetect calibration result in driver.
* Update RTT table according to the saved value.
* Write RTT back after modifying SW RTT table.
* Enable local mode for PeakDetect calibration and restore values.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacon transmission would get stuck if the NAV is
an invalid value for some reason. Check and correct
the NAV value in the HW when this happens.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All QCA chips have the ability to parse the CF Parameter Set
IE in beacons. If the IE is malformed in the beacons from some
APs [1], the HW locks up. In AP mode, a beacon stuck would happen
and in client mode, a disconnection usually is the result.
To fix this issue, set the AR_PCU_MISC_MODE2_CFP_IGNORE to ignore
the CFP IE in beacons - this is applicable for all chips. For
AP mode, if this issue happens, the NAV is also corrupted and has
to be reset - this will be done in a subsequent patch.
[1] : http://msujith.org/ath9k/cfp/Malformed-CF-Param.png
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX IQ calibration is disabled by default for AR9462, this
is done using the initvals (reg 0xa644).
But, to compensate for this, the AR_PHY_RX_DELAY register
should be set to the max allowed value when performing
calibration.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Marcel Holtmann
