Gitee limit the repo's size to 3GB, to reduce the size of the code,
sync codes to ock 5.4.119-20.0009.21 in one commit.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Sync kernel codes to the same with 590eaf1fec ("Init Repo base on
linux 5.4.32 long term, and add base tlinux kernel interfaces."), which
is from tk4, and it is the base of tk4.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Realtek Bluetooth controller provides a BT_DIS reset pin for hardware
reset of it. The cmd_timeout is helpful on Realtek bluetooth controller
where the firmware gets stuck.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix the issue that when the FW size is 32K+, it will fail for the download
process because of the incorrect index.
When firmware patch length is over 32K, "dl_cmd->index" may >= 0x80. It
will be thought as "data end" that download process will not complete.
However, driver should recount the index from 1.
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These printing macros already add a trailing newline, so drop these
unnecessary additional newlines.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
the rtl: or RTL: prefix in the string is pointless. The rtl_dev_* macros
already does that.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch is used to print fw version for debug convenience
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Realtek Bluetooth controllers can do both LE scan and BR/EDR inquiry
at once, need to set HCI_QUIRK_SIMULTANEOUS_DISCOVERY quirk.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When SoC receives pre shut down command, it share the same
with other COEX shared clients. So SoC needs a short time
after sending VS pre shutdown command before turning off
the regulators and sending the power off pulse. Along with
short delay, needs to wait for command complete event for
Pre shutdown VS command
Signed-off-by: Harish Bandi <c-hbandi@codeaurora.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some supported devices need more time to come out of reset (eg.
BCM4345C5 in AP6256).
I don't have/found a datasheet, so the value was arrive at
experimentally with the Oprange Pi 3 board. Without increased delay,
I got intermittent failures during probe. This is a Bluetooth 5.0
device, so maybe that's why it takes longer to initialize than the
others.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
QCA UART Bluetooth controllers can do both LE scan and BR/EDR inquiry
at once, need to set HCI_QUIRK_SIMULTANEOUS_DISCOVERY quirk.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Static structure qca_proto, of type hci_uart_proto, is used four times:
as the last argument in function hci_uart_register_device(), and as the
only argument to functions hci_uart_register_proto() and
hci_uart_unregister_proto(). In all three of these functions, the
parameter corresponding to qca_proto is declared as constant. Therefore,
make qca_proto itself constant as well in order to protect it from
unintended modification.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
From the perspective of controller, global suspend means there is no
SET_FEATURE (DEVICE_REMOTE_WAKEUP) and controller would drop the
firmware. It would consume less power. So we should not send this kind
of SET_FEATURE when host goes to suspend state.
Otherwise, when making device enter selective suspend, host should send
SET_FEATURE to make sure the firmware remains.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If CONFIG_ACPI is not set, gcc warn this:
drivers/bluetooth/hci_bcm.c:831:39: warning:
acpi_bcm_int_last_gpios defined but not used [-Wunused-const-variable=]
drivers/bluetooth/hci_bcm.c:838:39: warning:
acpi_bcm_int_first_gpios defined but not used [-Wunused-const-variable=]
move them to #ifdef CONFIG_ACPI block.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The qca_data structure is allocated with kzalloc() and hence
zero-initialized. Remove a bunch of unnecessary explicit
initializations of struct members to zero.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When returning from bpa10x_send_frame, it is necessary to propagate any
potential errno returned from usb_submit_urb.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Looks like Deadlock is observed in hci_qca while performing
stress and stability tests. Since same lock is getting
acquired from qca_wq_awake_rx and hci_ibs_tx_idle_timeout
seeing spinlock recursion, irqs should be disable while
acquiring the spinlock always.
Signed-off-by: Harish Bandi <c-hbandi@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reverts commit a0085f2510.
This commit has caused regressions in notebooks that support suspend
to idle such as the XPS 9360, XPS 9370 and XPS 9380.
These notebooks will wakeup from suspend to idle from an unsolicited
advertising packet from an unpaired BLE device.
In a bug report it was sugggested that this is caused by a generic
lack of LE privacy support. Revert this commit until that behavior
can be avoided by the kernel.
Fixes: a0085f2510 ("Bluetooth: btusb: driver to enable the usb-wakeup feature")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=200039
Link: https://marc.info/?l=linux-bluetooth&m=156441081612627&w=2
Link: https://chromium-review.googlesource.com/c/chromiumos/third_party/kernel/+/750073/
CC: Bastien Nocera <hadess@hadess.net>
CC: Christian Kellner <ckellner@redhat.com>
CC: Sukumar Ghorai <sukumar.ghorai@intel.com>
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Don't fall through to print error message when receive sleep indication
in HCI_IBS_RX_ASLEEP state, this is allowed behavior.
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch will reset the download flag to default value
before retrieving the download mode type.
Fixes: 32646db8cc ("Bluetooth: btqca: inject command complete event during fw download")
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Reviewed-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
WCN399x chips are coex chips, it needs a VS pre shutdown
command while turning off the BT. So that chip can inform
BT is OFF to other active clients.
Signed-off-by: Harish Bandi <c-hbandi@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The opcode of the command injected by commit 32646db8cc ("Bluetooth:
btqca: inject command complete event during fw download") uses the CPU
byte format, however it should always be little endian. In practice it
shouldn't really matter, since all we need is an opcode != 0, but still
let's do things correctly and keep sparse happy.
Fixes: 32646db8cc ("Bluetooth: btqca: inject command complete event during fw download")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On WCN3990 downloading the NVM sometimes fails with a "TLV response
size mismatch" error:
[ 174.949955] Bluetooth: btqca.c:qca_download_firmware() hci0: QCA Downloading qca/crnv21.bin
[ 174.958718] Bluetooth: btqca.c:qca_tlv_send_segment() hci0: QCA TLV response size mismatch
It seems the controller needs a short time after downloading the
firmware before it is ready for the NVM. A delay as short as 1 ms
seems sufficient, make it 10 ms just in case. No event is received
during the delay, hence we don't just silently drop an extra event.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix to return error code -EINVAL from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: a1c49c434e ("Bluetooth: btusb: Add protocol support for MediaTek MT7668U USB devices")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Certain ttys operations (pty_unix98_ops) lack tiocmget() and tiocmset()
functions which are called by the certain HCI UART protocols (hci_ath,
hci_bcm, hci_intel, hci_mrvl, hci_qca) via hci_uart_set_flow_control()
or directly. This leads to an execution at NULL and can be triggered by
an unprivileged user. Fix this by adding a helper function and a check
for the missing tty operations in the protocols code.
This fixes CVE-2019-10207. The Fixes: lines list commits where calls to
tiocm[gs]et() or hci_uart_set_flow_control() were added to the HCI UART
protocols.
Link: https://syzkaller.appspot.com/bug?id=1b42faa2848963564a5b1b7f8c837ea7b55ffa50
Reported-by: syzbot+79337b501d6aa974d0f6@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org # v2.6.36+
Fixes: b3190df628 ("Bluetooth: Support for Atheros AR300x serial chip")
Fixes: 118612fb91 ("Bluetooth: hci_bcm: Add suspend/resume PM functions")
Fixes: ff2895592f ("Bluetooth: hci_intel: Add Intel baudrate configuration support")
Fixes: 162f812f23 ("Bluetooth: hci_uart: Add Marvell support")
Fixes: fa9ad876b8 ("Bluetooth: hci_qca: Add support for Qualcomm Bluetooth chip wcn3990")
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reviewed-by: Yu-Chen, Cho <acho@suse.com>
Tested-by: Yu-Chen, Cho <acho@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Syzkaller found that it is possible to provoke a memory leak by
never freeing rx_skb in struct bcsp_struct.
Fix by freeing in bcsp_close()
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+98162c885993b72f19c4@syzkaller.appspotmail.com
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This device is functionally equivalent to the BT part of the RTL8723DE,
uses the same firmware, but the LMP subversion and HCI revision are unique.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some board requires explicitily control external osscilator via GPIO.
So, add an implementation of a clock property for an external oscillator
to the device.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Not every platform has the pinctrl device integrates the GPIO the function
such as MT7621 whose pinctrl and GPIO are separate hardware so the driver
adds additional boot-gpios to let the MT766[3,8]U can enter the proper boot
mode by gpiod for such platform.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BCM4359C0 BT/Wi-Fi compo chip needs an entry to be discovered
by the btbcm driver.
Tested using an AP6398S module from Ampak.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
QCA BTSOC NVM is a customized firmware file and different vendors may
want to have different BTSOC configuration (e.g. Configure SCO over PCM
or I2S, Setting Tx power, etc.) via this file. This patch will allow
vendors to download different NVM firmware file by reading a device
property "firmware-name".
Signed-off-by: Rocky Liao <rjliao@codeaurora.org>
Tested-by: Harish Bandi <c-hbandi@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds serdev support to the Marvell hci uart driver. Only basic
serdev support, none of the fancier features like regulator or enable
GPIO support is added for now.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For the Marvell HCI UART we have to upload two firmware files. The first
one is only for switching the baudrate of the device to a higher
baudrate. After the baudrate switching firmware has been uploaded the
device waits for a final ack (0x5a) before actually switching the
baudrate. To send this final ack with the old baudrate give the hci
ldisc workqueue a chance to run before switching the baudrate. Without
this the final ack will never be received by the device and firmware
upload fails.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci UART line discipline sends its characters in a workqueue. Some
devices like the Marvell Bluetooth chips need to make sure that all
queued characters are sent before switching the baudrate. This adds
a function to synchronize with the workqueue.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Firmware download to the WCN3990 often fails with a 'TLV response size
mismatch' error:
[ 133.064659] Bluetooth: hci0: setting up wcn3990
[ 133.489150] Bluetooth: hci0: QCA controller version 0x02140201
[ 133.495245] Bluetooth: hci0: QCA Downloading qca/crbtfw21.tlv
[ 133.507214] Bluetooth: hci0: QCA TLV response size mismatch
[ 133.513265] Bluetooth: hci0: QCA Failed to download patch (-84)
This is caused by a vendor event that corresponds to an earlier command
to change the baudrate. The event is not processed in the context of the
baudrate change and is later interpreted as response to the firmware
download command (which is also a vendor command), but the driver detects
that the event doesn't have the expected amount of associated data.
More details:
For the WCN3990 the vendor command for a baudrate change isn't sent as
synchronous HCI command, because the controller sends the corresponding
vendor event with the new baudrate. The event is received and decoded
after the baudrate change of the host port.
Identify the 'unused' event when it is received and don't add it to
the queue of RX frames.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Latest qualcomm chips are not sending an command complete event for
every firmware packet sent to chip. They only respond with a vendor
specific event for the last firmware packet. This optimization will
decrease the BT ON time. Due to this we are seeing a timeout error
message logs on the console during firmware download. Now we are
injecting a command complete event once we receive an vendor specific
event for the last RAM firmware packet.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Fix some warnings and one error reported by checkpatch.pl:
- lines longer than 80 characters are wrapped
- empty lines inserted to separate variable declarations from the actual
code
- line break inserted after if (...)
Co-developed-by: Thomas Röthenbacher <thomas.roethenbacher@fau.de>
Signed-off-by: Thomas Röthenbacher <thomas.roethenbacher@fau.de>
Signed-off-by: Fabian Schindlatz <fabian.schindlatz@fau.de>
Cc: linux-kernel@i4.cs.fau.de
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Realtek RTL8822BE BT chip on ASUS X420FA cannot be turned on correctly
after on-off several times. Bluetooth daemon sets BT mode failed when
this issue happens. Scanning must be active while turning off for this
bug to be hit.
bluetoothd[1576]: Failed to set mode: Failed (0x03)
If BT is turned off, then turned on again, it works correctly again.
According to the vendor driver, the HCI_QUIRK_RESET_ON_CLOSE flag is set
during probing. So, this patch makes Realtek's BT reset on close to fix
this issue.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203429
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Reviewed-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Extract the new function send_command_from_firmware from
download_firmware, which helps with the readability of the switch
statement. This way the code is less deeply nested and also no longer
exceeds the 80 character limit.
Co-developed-by: Thomas Röthenbacher <thomas.roethenbacher@fau.de>
Signed-off-by: Thomas Röthenbacher <thomas.roethenbacher@fau.de>
Signed-off-by: Fabian Schindlatz <fabian.schindlatz@fau.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Uploading the firmware needs quite a few seconds if done at 115200 kbps. So set
the operational frequency, usually 3 MHz, before uploading the firmware.
I have successfully tested this with a wl1837mod.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
BCM4356 devices soldered onto the PCB (non-removable) use an UART
connection for bluetooth, such as the Rock960, but it also advertise
btsdio support as a sdio function.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
CC: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Jianping Liu