S1G beacons are 802.11 Extension Frames, so the fixed
header part differs from regular beacons.
Add a handler to process S1G beacons and abstract out the
fetching of BSSID and element start locations in the
beacon body handler.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-14-thomas@adapt-ip.com
[don't rename, small coding style cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S1G allows listen interval up to 2^14 * 10000 beacon
intervals. In order to do this listen interval needs a
scaling factor applied to the lower 14 bits. Calculate
this and properly encode the listen interval for S1G STAs.
See IEEE802.11ah-2016 Table 9-44a for reference.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-10-thomas@adapt-ip.com
[move listen_int_usf into function using it]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Include the S1G Capabilities element in an association
request, and support the cfg80211 capability overrides.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-5-thomas@adapt-ip.com
[pass skb to ieee80211_add_s1g_capab_ie(), small code style edits]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling mod_timer for every rx/tx packet can be quite expensive.
Instead of constantly updating the timer, we can simply let it run out
and check the timestamp of the last ACK or rx packet to re-arm it.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-9-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mac80211.h says: Beacon filter support is advertised with the
IEEE80211_VIF_BEACON_FILTER interface capability. The driver needs to
enable beacon filter support whenever power save is enabled, that is
IEEE80211_CONF_PS is set. When power save is enabled, the stack will
not check for beacon loss and the driver needs to notify about loss
of beacons with ieee80211_beacon_loss().
Some controllers may want to dynamically enable the beacon filter
capabilities on power save entry (CONF_PS) and disable it on exit.
This is the case for the wcn36xx driver which only supports beacon
filtering in PS mode (no CONNECTION_MONITOR support).
When the mac80211 beacon monitor timer expires, the beacon filter
flag must be checked again in case it as been changed in between
(e.g. vif moved to PS mode).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1592471863-31402-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SAE authentication has been extended with H2E (IEEE 802.11 REVmd) and PK
(WFA) options. Those extensions use special status code values in the
SAE commit messages (Authentication frame with transaction sequence
number 1) to identify which extension is in use. mac80211 was
interpreting those new values as the AP denying authentication and that
resulted in failure to complete SAE authentication in some cases.
Fix this by adding exceptions for the new status code values 126 and
127.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20200731183830.18735-1-jouni@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is in fact 'disabled' in the spec, but there it's in a
place where that actually makes sense. In our internal data
structures, it doesn't really make sense, and in fact the
previous commit just fixed a bug in that area.
Make this safer by inverting the polarity from 'disabled' to
'enabled'.
Link: https://lore.kernel.org/r/20200730130051.5d8399545bd9.Ie62fdcd1a6cd9c969315bc124084a494ca6c8df3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adding bss-color configuration is only valid in HE mode.
Earlier we have enabled it by default, irrespective of
capabilities/mode. Fix that.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Link: https://lore.kernel.org/r/1594262781-21444-1-git-send-email-ppranees@codeaurora.org
[fix up commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Dan points out that if ieee80211_chandef_he_6ghz_oper() succeeds,
we don't initialize 'ret'. Initialize it to 0 in this case, since
everything went fine and nothing has to be disabled.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 57fa5e85d5 ("mac80211: determine chandef from HE 6 GHz operation")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200603111500.bd2a5ff37b83.I2c3f338ce343b581db493eb9a0d988d1b626c8fb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An AP supporting EMA (Enhanced Multi-BSSID advertisement) should set
bit 83 in the extended capabilities IE (9.4.2.26 in the 802.11ax D5 spec).
So the *3rd* bit of the 10th byte should be checked.
Also, in one place, the wrong byte was checked.
(cfg80211_find_ie returns a pointer to the beginning of the IE,
so the data really starts at ie[2], so the 10th byte
should be ie[12]. To avoid this confusion, use cfg80211_find_elem
instead).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Link: https://lore.kernel.org/r/20200528213443.4316121fa2a3.I9745582f8d41ad8e689dac0fefcd70b276d7c1ea@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the AP advertises inconsistent data, namely it has CCFS1 or CCFS2,
but doesn't advertise support for 160/80+80 bandwidth or "Extended NSS
BW Support", then we cannot use any MCSes in the the higher bandwidth.
Thus, avoid connecting with higher bandwidth since it's less efficient
that way.
Link: https://lore.kernel.org/r/20200528213443.0e55d40c3ccc.I6fd0b4708ebd087e5e46466c3e91f6efbcbef668@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
RX status needs a KHz component, so add freq_offset. We
can reduce the bits for the frequency since 60 GHz isn't
supported.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200402011810.22947-5-thomas@adapt-ip.com
[fix commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211_chan_def and ieee80211_channel recently gained a
frequency offset component. Handle this where it makes
sense (potentially required by S1G channels).
For IBSS, TDLS, CSA, and ROC we return -EOPNOTSUPP if a
channel with frequency offset is passed, since they may or
may not work. Once someone tests and verifies these
commands work on thos types of channels, we can remove
that error.
join_ocb and join_mesh look harmless because they use a
simple ieee80211_vif_use_channel(), which is using an
already verified channel, so we let those through.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200402011810.22947-4-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The MLME logic had a workaround that allowed to continue an
association with an AP even if the AP did not provide any basic
rates in its supported rates in the association response, assuming
that the first (non basic) legacy rate could be used as a basic rate.
However, this did not consider the case where the AP (which is
obviously buggy) did not provide any legacy rate.
Fix this by failing the association, as this can result in
an unexpected failure in the low level driver and FW, e.g., in
rate scale logic etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200326150855.d70a1450d83f.I6e6ce5efda351a8544c0e7bfeee260fe3360d401@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
SAE AP may reject authentication with WLAN_STATUS_ANTI_CLOG_REQUIRED.
As the user space will immediately continue the authentication flow,
there is no need to destroy the authentication data in this case.
This saves unneeded station removal and releasing the channel.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200326150855.7483996157a8.I8040a842874aaf6d209df3fc8a2acb97a0bf508b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Maintain the connection AID only in sdata->vif.bss_conf.aid, not
also in sdata->u.mgd.aid.
Keep setting that where we set ifmgd->aid before, which has the
side effect of exposing the AID to the driver before the station
entry (AP) is marked associated, in case it needs it then.
Requested-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/20200417123802.085d4a322b0c.I2e7a2ceceea8c6880219f9e9ee4d4ac985fd295a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support for disabling pre-auth rx over the nl80211 control
port for mac80211.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20200312091055.54257-3-markus.theil@tu-ilmenau.de
[fix indentation slightly, squash feature enablement]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The mptcp conflict was overlapping additions.
The SMC conflict was an additional and removal happening at the same
time.
Signed-off-by: David S. Miller <davem@davemloft.net>
The below-mentioned commit changed the code to unlock *inside*
the function, but previously the unlock was *outside*. It failed
to remove the outer unlock, however, leading to double unlock.
Fix this.
Fixes: 33483a6b88 ("mac80211: fix missing unlock on error in ieee80211_mark_sta_auth()")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Link: https://lore.kernel.org/r/20200221104719.cce4741cf6eb.I671567b185c8a4c2409377e483fd149ce590f56d@changeid
[rewrite commit message to better explain what happened]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
-----BEGIN PGP SIGNATURE-----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=CgmJ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2020-02-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
A few big new things:
* 802.11 frame encapsulation offload support
* more HE (802.11ax) support, including some for 6 GHz band
* powersave in hwsim, for better testing
Of course as usual there are various cleanups and small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
An AP that operates on 6GHz may respond with a broadcast probe response.
Don't ignore such frames.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-14-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We should not include the supported channels element if we have
(advertise) support for extended channel switching. To avoid any
interop issues because we always added it in the past, obey this
restriction only in the (new) 6 GHz band.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131113111.893106-1-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Disable HE if the beacon does not contain an HE operation IE.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-16-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The wireless device might be capable to connect HE
as well as the AP. However, the regulatory domain might
forbid it. Check whether the regulatory domain allows HE connection
when considering if HE IE should be added.
Also, add it when setting our peer capability.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-8-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check early on that a device has support for QoS (at least 4
queues) when it supports HT/VHT/HE, so we don't have to check
this while connecting.
This lets us clean up the code there: move some of it into
channel preparation to clean up a bit more, and then change
the logic to only check the "wmm_used" flag.
Additionally, disable HE consistently when VHT is disabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-3-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously I intended to ignore quiet mode in probe response, however
I ended up ignoring it instead for action frames. As a matter of fact,
this path isn't invoked for probe responses to start with. Just revert
this patch.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 7976b1e9e3 ("mac80211: ignore quiet mode in probe")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20200131111300.891737-15-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
commit 08a5bdde38 ("mac80211: consider QoS Null frames for STA_NULLFUNC_ACKED")
Fixed a bug where we failed to take into account a
nullfunc frame can be either non-QoS or QoS. It turns out
there is at least one more bug in
ieee80211_sta_tx_notify(), introduced in
commit 7b6ddeaf27 ("mac80211: use QoS NDP for AP probing"),
where we forgot to check for the QoS variant and so
assumed the QoS nullfunc frame never went out
Fix this by adding a helper ieee80211_is_any_nullfunc()
which consolidates the check for non-QoS and QoS nullfunc
frames. Replace existing compound conditionals and add a
couple more missing checks for QoS variant.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200114055940.18502-3-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is now possible to propagate BSS color settings into the subsystem. Lets
make mac80211 also handle them so that we can send them further down the
stack into the drivers. We drop the old bss_color field and change iwlwifi
to use the new he_bss_color struct.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20191217141921.8114-2-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We've already parsed the same data in the caller, so we can
pass it. The only thing is that we might fill in more details
in ieee80211_assoc_success(), but that doesn't bother the
caller, so it's fine to do even when we share the parsed data.
This reduces the stack space usage of the call stack here,
Arnd reported it had grown above the 1024 byte warning limit.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20191028125240.cb7661671bd2.I757c8752bf4f2f35e54f5e0a2c0a9cd9216c3d8b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Although this shouldn't occur in practice, it's a good idea to bounds
check the length field of the SSID element prior to using it for things
like allocations or memcpy operations.
Cc: <stable@vger.kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Reported-by: Nicolas Waisman <nico@semmle.com>
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20191004095132.15777-1-will@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we expire an inactive station, try to send it a deauth. This
helps if it's actually still around, and just has issues with
beacon distribution (or we do), and it will not also remove us.
Then, if we have shared state, this may not be reset properly,
causing problems; for example, we saw a case where aggregation
sessions weren't removed properly (due to the TX start being
offloaded to firmware and it relying on deauth for stop), causing
a lot of traffic to get lost due to the SN reset after remove/add
of the peer.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830112451.21655-9-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
"HE/HT/VHT" is a bit confusing since really the order of
development (and possible support) is different - change
this to "HT/VHT/HE".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190830112451.21655-4-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
802.11ay specification defines Enhanced Directional Multi-Gigabit
(EDMG) STA and AP which allow channel bonding of 2 channels and more.
Introduce new NL attributes that are needed for enabling and
configuring EDMG support.
Two new attributes are used by kernel to publish driver's EDMG
capabilities to the userspace:
NL80211_BAND_ATTR_EDMG_CHANNELS - bitmap field that indicates the 2.16
GHz channel(s) that are supported by the driver.
When this attribute is not set it means driver does not support EDMG.
NL80211_BAND_ATTR_EDMG_BW_CONFIG - represent the channel bandwidth
configurations supported by the driver.
Additional two new attributes are used by the userspace for connect
command and for AP configuration:
NL80211_ATTR_WIPHY_EDMG_CHANNELS
NL80211_ATTR_WIPHY_EDMG_BW_CONFIG
New rate info flag - RATE_INFO_FLAGS_EDMG, can be reported from driver
and used for bitrate calculation that will take into account EDMG
according to the 802.11ay specification.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Link: https://lore.kernel.org/r/1566138918-3823-2-git-send-email-ailizaro@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case of HE AP-STA link, ieee80211_send_nullfunc() will not
send the QOS NULL packet to check if AP is still associated.
In this case, probe_send_count will be non-zero and
ieee80211_sta_work() will later disassociate the AP, even
though no packet was ever sent.
Fix this by decrementing probe_send_count and not calling
ieee80211_send_nullfunc() in case of HE link, so that we
still wait for some time for the AP beacon to reappear and
don't disconnect right away.
Signed-off-by: Shay Bar <shay.bar@celeno.com>
Link: https://lore.kernel.org/r/20190703131848.22879-1-shay.bar@celeno.com
[clarify commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Store the OBSS PD parameters inside bss_conf when bringing up an AP and/or
when a station connects to an AP. This allows the driver to configure the
HW accordingly.
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/20190730163701.18836-3-john@phrozen.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Upon a successful assoc a station shall store the content of the HE
operation element inside bss_conf so that the driver can setup the
hardware accordingly.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20190729102342.8659-2-john@phrozen.org
[use struct copy]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In a very similar spirit to commit c470bdc1aa ("mac80211: don't WARN
on bad WMM parameters from buggy APs"), an AP may not transmit a
fully-formed WMM IE. For example, it may miss or repeat an Access
Category. The above loop won't catch that and will instead leave one of
the four ACs zeroed out. This triggers the following warning in
drv_conf_tx()
wlan0: invalid CW_min/CW_max: 0/0
and it may leave one of the hardware queues unconfigured. If we detect
such a case, let's just print a warning and fall back to the defaults.
Tested with a hacked version of hostapd, intentionally corrupting the
IEs in hostapd_eid_wmm().
Cc: stable@vger.kernel.org
Signed-off-by: Brian Norris <briannorris@chromium.org>
Link: https://lore.kernel.org/r/20190726224758.210953-1-briannorris@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 5.3:
API:
- Test shash interface directly in testmgr
- cra_driver_name is now mandatory
Algorithms:
- Replace arc4 crypto_cipher with library helper
- Implement 5 way interleave for ECB, CBC and CTR on arm64
- Add xxhash
- Add continuous self-test on noise source to drbg
- Update jitter RNG
Drivers:
- Add support for SHA204A random number generator
- Add support for 7211 in iproc-rng200
- Fix fuzz test failures in inside-secure
- Fix fuzz test failures in talitos
- Fix fuzz test failures in qat"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (143 commits)
crypto: stm32/hash - remove interruptible condition for dma
crypto: stm32/hash - Fix hmac issue more than 256 bytes
crypto: stm32/crc32 - rename driver file
crypto: amcc - remove memset after dma_alloc_coherent
crypto: ccp - Switch to SPDX license identifiers
crypto: ccp - Validate the the error value used to index error messages
crypto: doc - Fix formatting of new crypto engine content
crypto: doc - Add parameter documentation
crypto: arm64/aes-ce - implement 5 way interleave for ECB, CBC and CTR
crypto: arm64/aes-ce - add 5 way interleave routines
crypto: talitos - drop icv_ool
crypto: talitos - fix hash on SEC1.
crypto: talitos - move struct talitos_edesc into talitos.h
lib/scatterlist: Fix mapping iterator when sg->offset is greater than PAGE_SIZE
crypto/NX: Set receive window credits to max number of CRBs in RxFIFO
crypto: asymmetric_keys - select CRYPTO_HASH where needed
crypto: serpent - mark __serpent_setkey_sbox noinline
crypto: testmgr - dynamically allocate crypto_shash
crypto: testmgr - dynamically allocate testvec_config
crypto: talitos - eliminate unneeded 'done' functions at build time
...
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
The WEP code in the mac80211 subsystem currently uses the crypto
API to access the arc4 (RC4) cipher, which is overly complicated,
and doesn't really have an upside in this particular case, since
ciphers are always synchronous and therefore always implemented in
software. Given that we have no accelerated software implementations
either, it is much more straightforward to invoke a generic library
interface directly.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even if we have a station, we currently call rate_control_send_low()
with the NULL station unless further rate control (driver, minstrel)
has been initialized.
Change this so we can use more information about the station to use
a better rate. For example, when we associate with an AP, we will
now use the lowest rate it advertised as supported (that we can)
rather than the lowest mandatory rate. This aligns our behaviour
with most other 802.11 implementations.
To make this possible, we need to also ensure that we have non-zero
rates at all times, so in case we really have *nothing* pre-fill
the supp_rates bitmap with the very lowest mandatory bitmap (11b
and 11a on 2.4 and 5 GHz respectively).
Additionally, hostapd appears to be giving us an empty supported
rates bitmap (it can and should do better, since the STA must have
supported for at least the basic rates in the BSS), so ignore any
such bitmaps that would actually zero out the supp_rates, and in
that case just keep the pre-filled mandatory rates.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Turn TWT for STA interfaces when they associate and/or receive a
beacon where the twt_responder bit has changed.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When receiving a deauthentication/disassociation frame from a TDLS
peer, a station should not disconnect the current AP, but only
disable the current TDLS link if it's enabled.
Without this change, a TDLS issue can be reproduced by following the
steps as below:
1. STA-1 and STA-2 are connected to AP, bidirection traffic is running
between STA-1 and STA-2.
2. Set up TDLS link between STA-1 and STA-2, stay for a while, then
teardown TDLS link.
3. Repeat step #2 and monitor the connection between STA and AP.
During the test, one STA may send a deauthentication/disassociation
frame to another, after TDLS teardown, with reason code 6/7, which
means: Class 2/3 frame received from nonassociated STA.
On receive this frame, the receiver STA will disconnect the current
AP and then reconnect. It's not a expected behavior, purpose of this
frame should be disabling the TDLS link, not the link with AP.
Cc: stable@vger.kernel.org
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
FullMAC STAs have no way to update bss channel after CSA channel switch
completion. As a result, user-space tools may provide inconsistent
channel info. For instance, consider the following two commands:
$ sudo iw dev wlan0 link
$ sudo iw dev wlan0 info
The latter command gets channel info from the hardware, so most probably
its output will be correct. However the former command gets channel info
from scan cache, so its output will contain outdated channel info.
In fact, current bss channel info will not be updated until the
next [re-]connect.
Note that mac80211 STAs have a workaround for this, but it requires
access to internal cfg80211 data, see ieee80211_chswitch_work:
/* XXX: shouldn't really modify cfg80211-owned data! */
ifmgd->associated->channel = sdata->csa_chandef.chan;
This patch suggests to convert mac80211 workaround into cfg80211 behavior
and to update current bss channel in cfg80211_ch_switch_notify.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some buggy APs keep the CSA IE in probes after the channel
switch was completed and can silence us for no good reason.
Apply quiet mode only from beacons. If there is real channel
switch going on, we will see the beacon anyway.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, due to some buggy APs that continue to include
CSA IEs after the switch, we ignore CSA to same channel.
However, some other APs may do CSA to self in order to have
immediate quiet. Allow it. Do it only for beacons.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers may want to track further the CSA beacons, for example
to compensate for buggy APs that change the beacon count or quiet
mode during CSA flow.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case we receive a beacon without CSA IE while we are in
the middle of channel switch - abort the operation.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2018 REVmd of the spec introduces the max channel switch time
element which is optionally included in beacons/probes when there
is a channel switch / extended channel switch element.
The value represents the maximum delay between the time the AP
transmitted the last beacon in current channel and the expected
time of the first beacon in the new channel, in TU.
Parse the value and pass it to the driver.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This extends the NL80211_CMD_ASSOCIATE event case to report
NL80211_ATTR_REQ_IE similarly to what is already done with the
NL80211_CMD_CONNECT events if the driver provides this information. In
practice, this adds (Re)Association Request frame information element
reporting to mac80211 drivers for the cases where user space SME is
used.
This provides more information for user space to figure out which
capabilities were negotiated for the association. For example, this can
be used to determine whether HT, VHT, or HE is used.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set multi-bssid support flags according to driver support.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for multi-bssid.
This includes:
- Parsing multi-bssid element
- Overriding DTIM values
- Taking into account in various places the inner BSSID instead of
transmitter BSSID
- Save aside some multi-bssid properties needed by drivers
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In multiple BSSID, we have nested IEs inside the multiple
BSSID IE, that override the external ones for that specific
BSS. As preparation for supporting that, pass 2 BSSIDs to the
parse function, the transmitter, and the selected BSSID, so
it can know which IEs to choose. If the selected BSSID is
NULL, the outer ones will be applied.
Change ieee80211_bss_info_update to parse elements itself,
instead of receiving them parsed, so we have the relevant
bss entry in hand.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* virt_wifi - wireless control simulation on top of
another network interface
* hwsim configurability to test capabilities similar
to real hardware
* various mesh improvements
* various radiotap vendor data fixes in mac80211
* finally the nl_set_extack_cookie_u64() we talked
about previously, used for
* peer measurement APIs, right now only with FTM
(flight time measurement) for location
* made nl80211 radio/interface announcements more complete
* various new HE (802.11ax) things:
updates, TWT support, ...
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEH1e1rEeCd0AIMq6MB8qZga/fl8QFAlwaCwkACgkQB8qZga/f
l8S7mA/+I1CJmGC7Pvy+SBFkzoY5zEjjzgZYL6sGo16qMs89NPcURSe5j+uCsDP3
nKEjsvhQMYDfGNLTJJfWbDpGwm9LnKp69AFITlvfzmP6Sm36QMZr7oIC4abi8cW4
osaO3qfdaNoZ//x72jgjrFhUAnphvT2BsRVMNEjz7sXcDd7Jm9NnpRhV8zgXFvLF
dS2Ng51LM/BLMz5jQpyJUDZeeL/iBYybCecyckmVqzXPh1icIZETSqZXiN4ngv2A
6p9BSGNtP6wmjnbkvZz5RDq76VhTPZWsTgTpVb45Wf1k2fm1rB96UgpqvfQtjTgB
+7Zx2WRpMXM5OjGkwaEs8nawFmt7MHCGnhLPLWPCbXc685fhp3OFShysMJdYS/GZ
IIRJ7+IchAQX1yluftB+NkQM9sBDjyseMBwxHRYkj/rQVhoLY1sT+ke7lkuV10o6
DQqfpUTZAsIz7zkuscn7hkNdI/Rjub6BZjbrs1Jt9zSt9WQUBao23XudOI0j5JDa
ErnfC5PISXMQWik5B9M1Zhq3H9qCI2Swh19lMmtxtSDQ9yrLrJkEJ5SA+aHoxNHj
wSxBc3XXSW47qPXGX/D5DNnbOcOrE7kVZuD8YqRsy8VedyjIgEw7oQ21flAD4FC4
R4TgbNkqpfZQsU29gaMkDkYXnfQDB/G9FOk6ARGxjBPjT55Hz0E=
=EpyK
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-12-19' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have too many changes to list, highlights:
* virt_wifi - wireless control simulation on top of
another network interface
* hwsim configurability to test capabilities similar
to real hardware
* various mesh improvements
* various radiotap vendor data fixes in mac80211
* finally the nl_set_extack_cookie_u64() we talked
about previously, used for
* peer measurement APIs, right now only with FTM
(flight time measurement) for location
* made nl80211 radio/interface announcements more complete
* various new HE (802.11ax) things:
updates, TWT support, ...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When disabling HE due to the lack of HT/VHT, do it
at an earlier stage to avoid advertising HE capabilities IE.
Also, at this point, no need to check if AP supports HE, since
it is already checked earlier (in ieee80211_prep_channel).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Up until now, the IEEE80211_STA_DISABLE_HE flag was set only based
on whether the AP has advertised HE capabilities.
This flag should be set also if STA does not support HE
(regardless of the AP support).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Similar to WMM IE, if MU_EDCA IE parameters changed (or ceased to exist)
tell the Driver about it.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
TWT is a feature that was added in 11ah and enhanced in
11ax. There are two bits that need to be set if we want
to use the feature in 11ax: one in the HE Capability IE
and one in the Extended Capability IE. This is because
of backward compatibility between 11ah and 11ax.
In order to simplify the flow for the low level driver
in managed mode, aggregate the two bits and add a boolean
that tells whether TWT is supported or not, but only if
11ax is supported.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the missing unlock before return from function
ieee80211_mark_sta_auth() in the error handling case.
Cc: stable@vger.kernel.org
Fixes: fc107a9330 ("mac80211: Helper function for marking STA authenticated")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
[use result variable/label instead of duplicating]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previous implementation of SAE authentication in infrastructure BSS was
somewhat restricting and not exactly clean way of handling the two
auth() operations. This ended up removing and re-adding the STA entry
for the AP in the middle of authentication and also messing up
authentication state tracking through the sequence of four
Authentication frames. Furthermore, this did not work if the AP ended up
sending out SAE Confirm (auth trans #2) immediately after SAE Commit
(auth trans #1) before the station had time to transmit its SAE Confirm.
Clean up authentication state handling for the SAE case to allow two
rounds of auth() calls without dropping all state between those
operations. Track peer Confirmed status and mark authentication
completed only once both ends have confirmed.
ieee80211_mgd_auth() check for EBUSY cases is now handling only the
pending association (ifmgd->assoc_data) while all pending authentication
(ifmgd->auth_data) cases are allowed to proceed to allow user space to
start a new connection attempt from scratch even if the previously
requested authentication is still waiting completion. This is needed to
avoid making SAE error cases with retries take excessive amount of time
with no means for the user space to stop that (apart from setting the
netdev down).
As an extra bonus, the end of ieee80211_rx_mgmt_auth() can be cleaned up
to avoid the extra copy of the cfg80211_rx_mlme_mgmt() call for ongoing
SAE authentication since the new ieee80211_mark_sta_auth() helper
function can handle both completion of authentication and updates to the
STA entry under the same condition and there is no need to return from
the function between those operations.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This makes it easier to conditionally replace full allocation of
auth_data to use reallocation for the case of continuing SAE
authentication. Furthermore, there was not really any point in having
this check done so late in the function after having already completed
number of steps that cannot be used anyway in the error case.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Authentication exchange can be completed in both TX and RX paths for
SAE, so move this common functionality into a helper function to avoid
having to implement practically the same operations in two places when
extending SAE implementation in the following commits.
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After masking the he_oper_params, to get the requested values as
integers one must rshift and not lshift. Fix that by using the
le32_get_bits() macro.
Fixes: 41cbb0f5a2 ("mac80211: add support for HE")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
[converted to use le32_get_bits()]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With newer VHT implementations, it's necessary to look at the
HT operation's CCFS2 field to identify the actual bandwidth
used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* various A-MSDU building fixes (currently only affects mt76)
* syzkaller & spectre fixes in hwsim
* TXQ vs. teardown fix that was causing crashes
* embed WMM info in reg rule, bad code here had been causing crashes
* one compilation issue with fix from Arnd (rfkill-gpio includes)
* fixes for a race and bad data during/after channel switch
* nl80211: a validation fix, attribute type & unit fixes
along with other small fixes.
-----BEGIN PGP SIGNATURE-----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=lLBA
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2018-09-03' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here are quite a large number of fixes, notably:
* various A-MSDU building fixes (currently only affects mt76)
* syzkaller & spectre fixes in hwsim
* TXQ vs. teardown fix that was causing crashes
* embed WMM info in reg rule, bad code here had been causing crashes
* one compilation issue with fix from Arnd (rfkill-gpio includes)
* fixes for a race and bad data during/after channel switch
* nl80211: a validation fix, attribute type & unit fixes
along with other small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver fails to properly prepare for the channel
switch, mac80211 will disconnect. If the CSA IE had mode
set to 1, it means that the clients are not allowed to send
any Tx on the current channel, and that includes the
deauthentication frame.
Make sure that we don't send the deauthentication frame in
this case.
In iwlwifi, this caused a failure to flush queues since the
firmware already closed the queues after having parsed the
CSA IE. Then mac80211 would wait until the deauthentication
frame would go out (drv_flush(drop=false)) and that would
never happen.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When performing a channel switch flow for a managed interface, the
flow did not update the bandwidth of the AP station and the rate
scale algorithm. In case of a channel width downgrade, this would
result with the rate scale algorithm using a bandwidth that does not
match the interface channel configuration.
Fix this by updating the AP station bandwidth and rate scaling algorithm
before the actual channel change in case of a bandwidth downgrade, or
after the actual channel change in case of a bandwidth upgrade.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't need to check if he_oper is NULL before calling
ieee80211_verify_sta_he_mcs_support() as it - now - will
correctly check this itself. Remove the redundant check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
he_op is being dereferenced before it is null checked, hence there
is a potential null pointer dereference.
Fix this by moving the pointer dereference after he_op has been
properly null checked.
Notice that, currently, he_op is already being null checked before
calling this function at 4593:
4593 if (!he_oper ||
4594 !ieee80211_verify_sta_he_mcs_support(sband, he_oper))
4595 ifmgd->flags |= IEEE80211_STA_DISABLE_HE;
but in case ieee80211_verify_sta_he_mcs_support is ever called
without verifying he_oper is not null, we will end up having a
null pointer dereference. So, we better don't take any chances.
Addresses-Coverity-ID: 1470068 ("Dereference before null check")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for HE in mac80211 conforming with P802.11ax_D1.4.
Johannes: Fix another bug with the buf_size comparison in agg-rx.c.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function is passed many more parameters in the scan case
than in the MLME case, and differentiates the two cases inside.
Split it up and make both versions static to simplify things.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Add flags to pass through to probe request building and
change the "bool directed" to be one of them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
There are specific cases, such as SAE authentication exchange, that
might require long duration to complete. For such cases, add support
for indicating to the driver the required duration of the prepare_tx()
operation, so the driver would still be able to complete the frame
exchange.
Currently, indicate the duration only for SAE authentication exchange,
as SAE authentication can take up to 2000 msec (as defined in IEEE
P802.11-REVmd D1.0 p. 3504).
As the patch modified the prepare_tx() callback API, also modify
the relevant code in iwlwifi.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The IEEE P802.11-REVmd D1.0 specification updated the SAE authentication
timeout to be 2000 milliseconds (see dot11RSNASAERetransPeriod). Update
the SAE timeout setting accordingly.
While at it, reduce some code duplication in the timeout configuration.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit c470bdc1aa ("mac80211: don't WARN on bad WMM parameters from
buggy APs") handled cases where an AP reports a zeroed WMM
IE. However, the condition that checks the validity accessed the wrong
index in the ieee80211_tx_queue_params array, thus wrongly deducing
that the parameters are invalid. Fix it.
Fixes: c470bdc1aa ("mac80211: don't WARN on bad WMM parameters from buggy APs")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
first bullet here:
* EAPoL-over-nl80211 from Denis - this will let us fix
some long-standing issues with bridging, races with
encryption and more
* DFS offload support from the qtnfmac folks
* regulatory database changes for the new ETSI adaptivity
requirements
* various other fixes and small enhancements
-----BEGIN PGP SIGNATURE-----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=hI0F
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-03-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have a fair number of patches, but many of them are from the
first bullet here:
* EAPoL-over-nl80211 from Denis - this will let us fix
some long-standing issues with bridging, races with
encryption and more
* DFS offload support from the qtnfmac folks
* regulatory database changes for the new ETSI adaptivity
requirements
* various other fixes and small enhancements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Apparently, some APs are buggy enough to send a zeroed
WMM IE. Don't WARN on this since this is not caused by a bug
on the client's system.
This aligns the condition of the WARNING in drv_conf_tx
with the validity check in ieee80211_sta_wmm_params.
We will now pick the default values whenever we get
a zeroed WMM IE.
This has been reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=199161
Fixes: f409079bb6 ("mac80211: sanity check CW_min/CW_max towards driver")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If userspace requested control port frames to go over 80211, then do so.
The control packets are intercepted just prior to delivery of the packet
to the underlying network device.
Pre-authentication type frames (protocol: 0x88c7) are also forwarded
over nl80211.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We already have 'ifmgd' here, and it's already assigned
to the same value, so remove the duplicate.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ETSI has recently added new requirements that restrict the WMM
parameter values for 5GHz frequencies. We need to take care of the
following scenarios in order to comply with these new requirements:
1. When using mac80211 default values;
2. When the userspace tries to configure its own values;
3. When associating to an AP which advertises WWM IE.
When associating to an AP, the client uses the values in the
advertised WMM IE. But the AP may not comply with the new ETSI
requirements, so the client needs to check the current regulatory
rules and use those limits accordingly.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the low-level driver returns an invalid RSSI indication,
set the signal value to 0 as an indication to the upper layer.
Also, skip average level computation if signal is invalid.
Signed-off-by: Jean Pierre TOSONI <jp.tosoni@acksys.fr>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 7b6ddeaf27 ("mac80211: use QoS NDP for AP probing") added an
argument qos_ok to ieee80211_nullfunc_get to support QoS NDP. Despite
the claim in the commit log "Change all the drivers to *not* allow
QoS NDP for now, even though it looks like most of them should be OK
with that", this commit enables QoS NDP in response to beacons (see
change to mlme.c:ieee80211_send_nullfunc), causing ath9k_htc to lose
IP connectivity. See:
https://patchwork.kernel.org/patch/10241109/https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=891060
Introduce a hardware flag to allow such buggy drivers to override the
correct default behaviour of mac80211 of sending QoS NDP packets.
Signed-off-by: Ben Caradoc-Davies <ben@transient.nz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In multi channel scenarios, when disassociating from the AP before a
beacon was heard from the AP, it is not guaranteed that the virtual
interface is granted air time for the transmission of the
deauthentication frame. This in turn can lead to various issues as
the AP might never get the deauthentication frame.
To mitigate such possible issues, add a HW flag indicating that the
driver requires mac80211 to call the mgd_prep_tx() driver callback
to make sure that the virtual interface is granted immediate airtime
to be able to transmit the frame, in case that no beacon was heard
from the AP.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extracting the TID from the QOS header is common enough
to justify helper.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While the change between 802.11-2012 and 802.11-2016 to move from
requiring APs to set the two top bits to now requiring them to be
cleared was apparently unintentional and will be fixed, clients
should either way assume that the top five bits are reserved and
ignore them.
Implement that in mac80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in some cases I replaced "fall through on else" and
"otherwise fall through" comments with just a "fall through" comment,
which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When connected to a QoS/WMM AP, mac80211 should use a QoS NDP
for probing it, instead of a regular non-QoS one, fix this.
Change all the drivers to *not* allow QoS NDP for now, even
though it looks like most of them should be OK with that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code here (more or less accidentally) tracks the HT capability of
the AP when connected, and we found at least one AP that erroneously
toggles its 20/40 capability bit when changing between 20/40 MHz. The
connection to the AP is then broken because we set the 40 MHz disable
flag based on this, as soon as it switches to 20 MHz, but because the
flag then changed, we disconnect.
I'd be inclined to just ignore this issue, since we then reconnect
while the AP is in 20 MHz mode and never use 40 MHz with it again,
but this code is a bit strange anyway - we don't use the capabilities
for anything else.
Change the code to simply not track the HT capabilities at all, which
assumes that the AP at least sets 20/40 capability when operating in
40 MHz (or higher). If not, rate scaling might end up using only the
narrower bandwidth.
The new behaviour also mirrors what VHT does, where we only check the
VHT operation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to split off IEs from the ones obtained
from userspace, if they were already split off, so for
example IEs that went before HT don't have to be listed
again to go before VHT. Simplify the code here so it's
clearer.
While at it, also clarify the comments regarding the DMG
(60 GHz) elements.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
this fix minor issue in the log message.
in ieee80211_rx_mgmt_assoc_resp function, when assigning the
reassoc value from the mgmt frame control:
ieee80211_is_reassoc_resp function need to be used, instead of
ieee80211_is_reassoc_req function.
Signed-off-by: Simon Dinkin <simon.dinkin@tandemg.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were many places that my previous spatch didn't find,
as pointed out by yuan linyu in various patches.
The following spatch found many more and also removes the
now unnecessary casts:
@@
identifier p, p2;
expression len;
expression skb;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_zero(skb, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_zero(skb, len);
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, len);
|
-memset(p, 0, len);
)
@@
type t, t2;
identifier p, p2;
expression skb;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, sizeof(*p));
|
-memset(p, 0, sizeof(*p));
)
@@
expression skb, len;
@@
-memset(skb_put(skb, len), 0, len);
+skb_put_zero(skb, len);
Apply it to the tree (with one manual fixup to keep the
comment in vxlan.c, which spatch removed.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mac80211 changes the channel, it also calls into the driver's
bss_info_changed() callback, e.g. with BSS_CHANGED_IDLE. The driver
may, like iwlwifi does, access more data from bss_info in that case
and iwlwifi accesses the basic_rates bitmap, but if changing from a
band with more (basic) rates to one with fewer, an out-of-bounds
access of the rate array may result.
While we can't avoid having invalid data at some point in time, we
can avoid having it while we call the driver - so set up all the
data before configuring the channel, and then apply it afterwards.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=195677
Reported-by: Johannes Hirte <johannes.hirte@datenkhaos.de>
Tested-by: Johannes Hirte <johannes.hirte@datenkhaos.de>
Debugged-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need for the station MLME code to handle bitrates for 5
or 10 MHz channels when it can't ever create such a configuration.
Remove the unnecessary code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clear the csa_ie in ieee80211_parse_ch_switch_ie() where the data
is filled in, rather than in each caller.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If ieee80211_hw_restart() is called during authentication, the
authentication process will continue, causing the driver to be called
in a wrong state. This ultimately causes an oops in the iwlwifi
driver (at least).
This fixes bugzilla 195299 partly.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195299
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Parse the BSS max idle period element and set the BSS configuration
accordingly so the driver can use this information to configure the
max idle period and to use protected management frames for keep alive
when required.
The BSS max idle period element is defined in IEEE802.11-2016,
section 9.4.2.79
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Existing API 'ieee80211_get_sdata_band' returns default 2 GHz band even
if the channel context configuration is NULL. This crashes for chipsets
which support 5 Ghz alone when it tries to access members of 'sband'.
Channel context configuration can be NULL in multivif case and when
channel switch is in progress (or) when it fails. Fix this by replacing
the API 'ieee80211_get_sdata_band' with 'ieee80211_get_sband' which
returns a NULL pointer for sband when the channel configuration is NULL.
An example scenario is as below:
In multivif mode (AP + STA) with drivers like ath10k, when we do a
channel switch in the AP vif (which has a number of clients connected)
and a STA vif which is connected to some other AP, when the channel
switch in AP vif fails, while the STA vifs tries to connect to the
other AP, there is a window where the channel context is NULL/invalid
and this results in a crash while the clients connected to the AP vif
tries to reconnect and this race is very similar to the one investigated
by Michal in https://patchwork.kernel.org/patch/3788161/ and this does
happens with hardware that supports 5Ghz alone after long hours of
testing with continuous channel switch on the AP vif
ieee80211 phy0: channel context reservation cannot be finalized because
some interfaces aren't switching
wlan0: failed to finalize CSA, disconnecting
wlan0-1: deauthenticating from 8c:fd:f0:01:54:9c by local choice
(Reason: 3=DEAUTH_LEAVING)
WARNING: CPU: 1 PID: 19032 at net/mac80211/ieee80211_i.h:1013 sta_info_alloc+0x374/0x3fc [mac80211]
[<bf77272c>] (sta_info_alloc [mac80211])
[<bf78776c>] (ieee80211_add_station [mac80211]))
[<bf73cc50>] (nl80211_new_station [cfg80211])
Unable to handle kernel NULL pointer dereference at virtual
address 00000014
pgd = d5f4c000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
PC is at sta_info_alloc+0x380/0x3fc [mac80211]
LR is at sta_info_alloc+0x37c/0x3fc [mac80211]
[<bf772738>] (sta_info_alloc [mac80211])
[<bf78776c>] (ieee80211_add_station [mac80211])
[<bf73cc50>] (nl80211_new_station [cfg80211]))
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the user rate mask results in no (basic) rates being usable,
clear it. Also, if we're already operating when it's set, reject
it instead.
Technically, selecting basic rates as the criterion is a bit too
restrictive, but calculating the usable rates over all stations
(e.g. in AP mode) is harder, and all stations must support the
basic rates. Similarly, in client mode, the basic rates will be
used anyway for control frames.
This fixes the "no supported rates (...) in rate_mask ..." warning
that occurs on TX when you've selected a rate mask that's not
compatible with the connection (e.g. an AP that enables only the
rates 36, 48, 54 and you've selected only 6, 9, 12.)
Reported-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There isn't really much harm in not ignoring, since it doesn't
represent a valid rate, but since we already ignore the HT one
also ignore VHT. Also simplify the code a bit.
Fix a typo in the related comment (pointed out by Arend) while
at it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When disassociation happens only numeric reason is printed
in ieee80211_rx_mgmt_disassoc(). Add text variant, too.
Signed-off-by: Arkadiusz Miśkiewicz <arekm@maven.pl>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support .set_cqm_rssi_range_config if the beacons are available for
processing in mac80211. There's no reason that this couldn't be
offloaded by mac80211-based drivers but there's no driver method for
that added in this patch.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Update the drivers to pass the RSSI level as a cfg80211_cqm_rssi_notify
parameter and pass this value to userspace in a new nl80211 attribute.
This helps both userspace and also helps in the implementation of the
multiple RSSI thresholds CQM mechanism.
Note for marvell/mwifiex I pass 0 for the RSSI value because the new
RSSI value is not available to the driver at the time of the
cfg80211_cqm_rssi_notify call, but the driver queries the new value
immediately after that, so it is actually available just a moment later
if we wanted to defer caling cfg80211_cqm_rssi_notify until that moment.
Without this, the new cfg80211 code (patch 3) will call .get_station
which will send a duplicate HostCmd_CMD_RSSI_INFO command to the hardware.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend ieee80211_cqm_rssi_notify with a rssi_level parameter so that
this information can be passed to netlink clients in the next patch, if
available. Most drivers will have this value at hand. wl1251 receives
events from the firmware that only tell it whether latest measurement
is above or below threshold so we don't pass any value at this time
(parameter is 0).
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 4a733ef1be (mac80211: remove PM-QoS listener) removed all use
of 'beaconint_us' from ieee80211_recalc_ps() but left the variable
intact. Compiling with W=1 gives the following warning, fix it.
net/mac80211/mlme.c: In function ‘ieee80211_recalc_ps’:
net/mac80211/mlme.c:1481:7: warning: variable ‘beaconint_us’ set but not used [-Wunused-but-set-variable]
iee80211_tu_to_usec has no side-effects and is safe to remove.
Fixes: 4a733ef1be ("mac80211: remove PM-QoS listener")
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kirtika Ruchandani <kirtika@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When mac80211 abandons an association attempt, it may free
all the data structures, but inform cfg80211 and userspace
about it only by sending the deauth frame it received, in
which case cfg80211 has no link to the BSS struct that was
used and will not cfg80211_unhold_bss() it.
Fix this by providing a way to inform cfg80211 of this with
the BSS entry passed, so that it can clean up properly, and
use this ability in the appropriate places in mac80211.
This isn't ideal: some code is more or less duplicated and
tracing is missing. However, it's a fairly small change and
it's thus easier to backport - cleanups can come later.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds support for encrypting (Re)Association Request frame and
decryption (Re)Association Response frame when using FILS in station
mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The special SAE case should be limited only for SAE since the more
generic AUTH_DATA can now be used with other authentication algorithms
as well.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds defines and nl80211 extensions to allow FILS Authentication to
be implemented similarly to SAE. FILS does not need the special rules
for the Authentication transaction number and Status code fields, but it
does need to add non-IE fields. The previously used
NL80211_ATTR_SAE_DATA can be reused for this to avoid having to
duplicate that implementation. Rename that attribute to more generic
NL80211_ATTR_AUTH_DATA (with backwards compatibility define for
NL80211_SAE_DATA).
Also document the special rules related to the Authentication
transaction number and Status code fiels.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The uapsd_queue field is in QoS IE order and not in
IEEE80211_AC_*'s order.
This means that mac80211 would get confused between
BK and BE which is certainly not such a big deal but
needs to be fixed.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the unlikely situation that the supplicant has negotiated
admission for the background AC (which it has no reason to as
it's not supposed to be requiring admission control to start
with, and we'd ignore such a requirement anyway), the loop
here may terminate with non_acm_ac == 4, which leads to an
array overrun.
Check this explicitly just for completeness.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, after a sudden AP disappearing and reconnection to
another AP in the same ESS, user space gets the old AP in scan
results (cached). User space may decide to roam to that old AP
which will cause a disconnection and longer recovery.
Remove APs that are probably out of range from BSS table.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The regular RX path has a lot of code, but with a few
assumptions on the hardware it's possible to reduce the
amount of code significantly. Currently the assumptions
on the driver are the following:
* hardware/driver reordering buffer (if supporting aggregation)
* hardware/driver decryption & PN checking (if using encryption)
* hardware/driver did de-duplication
* hardware/driver did A-MSDU deaggregation
* AP_LINK_PS is used (in AP mode)
* no client powersave handling in mac80211 (in client mode)
of which some are actually checked per packet:
* de-duplication
* PN checking
* decryption
and additionally packets must
* not be A-MSDU (have been deaggregated by driver/device)
* be data packets
* not be fragmented
* be unicast
* have RFC 1042 header
Additionally dynamically we assume:
* no encryption or CCMP/GCMP, TKIP/WEP/other not allowed
* station must be authorized
* 4-addr format not enabled
Some data needed for the RX path is cached in a new per-station
"fast_rx" structure, so that we only need to look at this and
the packet, no other memory when processing packets on the fast
RX path.
After doing the above per-packet checks, the data path collapses
down to a pretty simple conversion function taking advantage of
the data cached in the small fast_rx struct.
This should speed up the RX processing, and will make it easier
to reason about parallelizing RX (for which statistics will need
to be per-CPU still.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the likely case that probe_count is 0, don't write to the
memory there.
Also use ifmgd consistently in the function, instead of using
sdata->u.mgd as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers may need to track which vif is using VHT MU-MIMO.
Move the flag indicationg the ownership of MU_MIMO to
ieee80211_vif.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make sure there's at least a debug message whenever the
connection to the AP is terminated.
Also change one message from wiphy_debug() to the common
mlme_dbg().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The station MLME and IBSS/mesh ones use entirely different
code for interpreting HT and VHT operation elements. Change
the code that interprets them a bit - it now modifies an
existing chandef - and use it also in the MLME code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During a sw scan ieee80211_iface_work ignores work items for all vifs.
However after the scan complete work is requeued only for STA, ADHOC
and MESH iftypes.
This occasionally results in event processing getting delayed/not
processed for iftype AP when it coexists with a STA. This can result
in data halt and eventually disconnection on the AP interface.
Cc: stable@vger.kernel.org
Signed-off-by: Sachin Kulkarni <Sachin.Kulkarni@imgtec.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use to_delayed_work() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Group ID Management frame is an Action frame of
category VHT. It is transmitted by the AP to assign
or change the user position of a STA for one or more
group IDs.
Process and save the group membership data. Notify
underlying driver of changes.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
An AP can send an operating channel width change in a beacon
opmode notification IE as long as there's a change in the nss as
well (See 802.11ac-2013 section 10.41).
So don't limit updating to nss only from an opmode notification IE.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the AP is advertising limited TX power, the message can be
printed over and over again. Suppress it when the power level
isn't changing.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=106011
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add new VIF flag, that will allow get NOA update
notification when driver will request this, even
this is not pure P2P vif (eg. STA vif).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As WMM is required for HT/VHT operation, treat bad WMM parameters
more gracefully by falling back to default parameters instead of
not using WMM assocation. This makes it possible to still use HT
or VHT, although potentially with reduced quality of service due
to unintended WMM parameters.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Disabling WMM has a huge impact these days. It implies that
HT and VHT will be disabled which means that the throughput
will be drammatically reduced.
Since the AIFSN is a transmission parameter, we can play a
bit and fix it up to make it compliant with the 802.11
specification which requires it to be at least 2.
Increasing it from 1 to 2 will slightly reduce the
likelyhood to get a transmission opportunity compared to
other clients that would accept to set AIFSN=1, but at
least it will allow HT and VHT which is a huge gain.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function currently determines this value, for use in bss_info.qos,
based on the interface type itself. Make it a parameter instead and
set it with the same logic for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Local request to deauthenticate wasn't handled while associating, thus
the association could continue even when the user space required to
disconnect.
Cc: stable@vger.kernel.org
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's little point in keeping (and even sending to userspace)
the beacon_loss_count value per station, since it can only apply
to the AP on a managed-mode connection. Move the value to ifmgd,
advertise it only in managed mode, and remove it from ethtool as
it's available through better interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As this API has never really seen any use and most drivers don't
ever use the value derived from it, remove it.
Change the only driver using it (rt2x00) to simply use the DTIM
period instead of the "max sleep" time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 5c48f12017.
Some device drivers (ath10k) offload part of aggregation including AddBA/DelBA
negotiations to firmware. In such scenario, the PMF configuration of
the station needs to be provided to driver to enable encryption of
AddBA/DelBA action frames.
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* many internal fixes, API improvements, cleanups, etc.
* full AP client state tracking in cfg80211/mac80211 from Ayala
* VHT support (in mac80211) for mesh
* some A-MSDU in A-MPDU support from Emmanuel
* show current TX power to userspace (from Rafał)
* support for netlink dump in vendor commands (myself)
-----BEGIN PGP SIGNATURE-----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=BF9F
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-10-05' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For the current cycle, we have the following right now:
* many internal fixes, API improvements, cleanups, etc.
* full AP client state tracking in cfg80211/mac80211 from Ayala
* VHT support (in mac80211) for mesh
* some A-MSDU in A-MPDU support from Emmanuel
* show current TX power to userspace (from Rafał)
* support for netlink dump in vendor commands (myself)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of int with 0/1, use bool with false/true for the
powersave argument to ieee80211_send_nullfunc().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of nesting two if statements, inline the second
check into the first if statement and to indentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It doesn't seem problematic to change the weight for the average
beacon signal from 3 to 4, so use DECLARE_EWMA. This also makes
the code easier to maintain since bugs like the one fixed in the
previous patch can't happen as easily.
With a fix from Avraham Stern to invert the sign since EMWA uses
unsigned values only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ifmgd->ave_beacon_signal value cannot be taken as is for
comparisons, it must be divided by since it's represented
like that for better accuracy of the EWMA calculations. This
would lead to invalid driver RSSI events. Fix the used value.
Fixes: 615f7b9bb1 ("mac80211: add driver RSSI threshold events")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These file aren't really useful:
- if per beacon data is required then you need to use
radiotap or similar anyway, debugfs won't help much
- average beacon signal is reported in station info in
nl80211 and can be looked up with iw
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The direct probe step before authentication was done mostly for
two reasons:
1) the BSS data could be stale
2) the beacon might not have included all IEs
The concern (1) doesn't really seem to be relevant any more as
we time out BSS information after about 30 seconds, and in fact
the original patch only did the direct probe if the data was
older than the BSS timeout to begin with. This condition got
(likely inadvertedly) removed later though.
Analysing this in more detail shows that since we mostly use
data from the association response, the only real reason for
needing the probe response was that the code validates the WMM
parameters, and those are optional in beacons. As the previous
patches removed that behaviour, we can now remove the direct
probe step entirely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently if 80MHz channels are not allowed for use, the VHT IE is not
included in the probe request for an AP. This is not good enough if the
AP is configured with the wrong regulatory and supports VHT even where
prohibited or in TDLS scenarios.
Mark the ifmgd with the DISABLE_VHT flag for the misbehaving-AP case, and
unset VHT support from the peer-station entry for the TDLS case.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for declaring MU-MIMO beamformee capability for
relevant hardware.
When sending association request, the capability is included if both
hardware and the AP support it, and no other virtual interface
is using it.
This is in order to avoid multiple interfaces using MU-MIMO in parallel
which might lead to contradictions in the group-id mechanism.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The IEEE802.11-2012 specification is vague regarding SMPS operation during
TDLS. It does not define a clear way to transition between SMPS states.
To avoid interop issues, set SMPS to off when TDLS peers are connected.
Accomplish this by extending the definition of the AUTOMATIC state. If the
driver forces a state other than OFF, disconnect all TDLS peers.
While at it, avoid changing the SMPS state of the peer STA. We have no
way to control it, so try and behave correctly towards it.
Move the TDLS peer-teardown function to where the rest of the TDLS code
resides.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As we're running out of hardware capability flags pretty quickly,
convert them to use the regular test_bit() style unsigned long
bitmaps.
This introduces a number of helper functions/macros to set and to
test the bits, along with new debugfs code.
The occurrences of an explicit __clear_bit() are intentional, the
drivers were never supposed to change their supported bits on the
fly. We should investigate changing this to be a per-frame flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There were a few rare cases when upon
authentication failure channel wasn't released.
This could cause stale pointers to remain in
chanctx assigned_vifs after interface removal and
trigger general protection fault later.
This could be triggered, e.g. on ath10k with the
following steps:
1. start an AP
2. create 2 extra vifs on ath10k host
3. connect vif1 to the AP
4. connect vif2 to the AP
(auth fails because ath10k firmware isn't able
to maintain 2 peers with colliding AP mac
addresses across vifs and consequently
refuses sta_info_insert() in
ieee80211_prep_connection())
5. remove the 2 extra vifs
6. goto step 2; at step 3 kernel was crashing:
general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC
Modules linked in: ath10k_pci ath10k_core ath
...
Call Trace:
[<ffffffff81a2dabb>] ieee80211_check_combinations+0x22b/0x290
[<ffffffff819fb825>] ? ieee80211_check_concurrent_iface+0x125/0x220
[<ffffffff8180f664>] ? netpoll_poll_disable+0x84/0x100
[<ffffffff819fb833>] ieee80211_check_concurrent_iface+0x133/0x220
[<ffffffff81a0029e>] ieee80211_open+0x3e/0x80
[<ffffffff817f2d26>] __dev_open+0xb6/0x130
[<ffffffff817f3051>] __dev_change_flags+0xa1/0x170
...
RIP [<ffffffff81a23140>] ieee80211_chanctx_radar_detect+0xa0/0x170
(gdb) l * ieee80211_chanctx_radar_detect+0xa0
0xffffffff81a23140 is in ieee80211_chanctx_radar_detect (/devel/src/linux/net/mac80211/util.c:3182).
3177 */
3178 WARN_ON(ctx->replace_state == IEEE80211_CHANCTX_REPLACES_OTHER &&
3179 !list_empty(&ctx->assigned_vifs));
3180
3181 list_for_each_entry(sdata, &ctx->assigned_vifs, assigned_chanctx_list)
3182 if (sdata->radar_required)
3183 radar_detect |= BIT(sdata->vif.bss_conf.chandef.width);
3184
3185 return radar_detect;
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are no drivers setting IEEE80211_HW_2GHZ_SHORT_SLOT_INCAPABLE
or IEEE80211_HW_2GHZ_SHORT_PREAMBLE_INCAPABLE, so any code using the
two flags is dead; it's also exceedingly unlikely that any new driver
could ever need to set these flags.
The wcn36xx code is almost certainly broken, but this preserves the
previous behaviour.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When trying to associate, the AP could send a deauth frame instead.
Currently mac80211 drops that frame and doesn't report it to the
supplicant, which, in some versions and/or in certain circumstances
will simply keep trying to associate over and over again instead of
trying authentication again.
Fix this by reacting to deauth frames while associating, reporting
them to the supplicant and dropping the association attempt (which
is bound to fail.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a station does a channel switch, it's not well defined what its TDLS
peers would do. Avoid a situation when the local side marks a potentially
disconnected peer as a TDLS peer.
Keeping peers connected through CSA is doubly problematic with the upcoming
TDLS WIDER-BW feature which allows peers to widen the BSS channel. The
new channel transitioned-to might not be compatible and would require
a re-negotiation anyway.
Make sure to disallow new TDLS link during CSA.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
HT and VHT override configurations were ignored during association and
applied only when first beacon recived, or not applied at all.
Fix the code to apply HT/VHT overrides during association. This is a bit
tricky since the channel was already configured during authentication
and we don't want to reconfigure it unless there's really a change.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This changes a couple of messages from sdata_info to sdata_dbg.
This should reduce some log spam, as reported here:
https://bugzilla.redhat.com/show_bug.cgi?id=1206468
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
-----BEGIN PGP SIGNATURE-----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=O/cf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Lots of updates for net-next; along with the usual flurry
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Indicating just the peer's capability is fairly pointless
if the local device doesn't support it. Make the variable
track both combined, and remove the 'local support' check
in the TX path.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Louis reported that a static checker was complaining that
the 'dst' variable was set (multiple times) but not used.
This is due to a previous commit having removed the usage
(apparently erroneously), so add it back.
Fixes: a344d6778a ("mac80211: allow drivers to support NL80211_SCAN_FLAG_RANDOM_ADDR")
Reported-by: Louis Langholtz <lou_langholtz@me.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stop scan before authentication or association to make sure
that nothing interferes with connection flow.
Currently mac80211 defers RX auth and assoc packets (among other ones)
until after the scan is complete, so auth during scan is likely to fail
if scan took too much time.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can allow the driver to take action based on the reason
of the deauth.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can allow the driver to take action based on the
success / failure of the association.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can allow the driver to take action based on the
success / failure of the authentication.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We will be able to add more events, such as MLME events and
others. The low level driver may be interested in knowing
about these events to dump firmware data upon failures, or
to change parameters in case connection attempts fail etc...
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the AP is confused and starts doing a CSA to the same channel,
just ignore that request instead of trying to act it out since it
was likely sent in error anyway.
In the case of the bug I was investigating the GO was misbehaving
and sending out a beacon with CSA IEs still included after having
actually done the channel switch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a beacon from the AP contains only the ECSA IE, and not a CSA IE
as well, this ECSA IE is not considered for calculating the CRC and
the beacon might be dropped as not being interesting. This is clearly
wrong, it should be handled and the channel switch should be executed.
Fix this by including the ECSA IE ID in the bitmap of interesting IEs.
Reported-by: Gil Tribush <gil.tribush@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The schedule_work()/mutex unlocking code is duplicated many times,
refactor that to a common place in the function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some device drivers offload part of aggregation including AddBA/DelBA
negotiations to firmware. In such scenario, the PMF configuration of
the station needs to be provided to driver to enable encryption of
AddBA/DelBA action frames.
Signed-off-by: SenthilKumar Jegadeesan <sjegadee@qti.qualcomm.com>
[fix commit log, documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In ieee80211_queue_work() we check if we're quiescing or suspended, so
it's not necessary to check for quiescing before calling this
function. Remove duplicate checks.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since cfg80211 disconnects, but has no insight into the association
process, it can happen that it disconnects while association is in
progress. We then try to abort association in mac80211, but this is
only later so the association can complete between the two.
This results in removing an interface from the driver while bound
to the channel context, obviously causing confusion and issues.
Solve this by also checking if we're associated during quiesce and
if so deauthenticating. The frame will no longer go out to the AP
which is a bit unfortunate, but it'll resolve the crash (and before
we would have suspended without telling the AP as well.)
I'm working on a better, but more complex solution as well, which
should avoid that problem.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon's timestamp, device system time associated with this beacon and
DTIM count parameters are not updated in the associated vif context
if the latest beacon's content is identical to the previously received.
It make sense to update these changing parameters on every beacon so the
driver can get most updated values. This may be necessary, for example,
to avoid either beacons' drift effect or device time stamp overrun.
IMPORTANT: Three sync_* parameters - sync_ts, sync_device_ts and
sync_dtim_count would possibly be out of sync by the time the driver will
use them. The synchronized view is currently guaranteed only in certain
callbacks.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* revert a patch that caused a regression with mesh userspace (Bob)
* fix a number of suspend/resume related races
(from Emmanuel, Luca and myself - we'll look at backporting later)
* add software implementations for new ciphers (Jouni)
* add a new ACPI ID for Broadcom's rfkill (Mika)
* allow using netns FD for wireless (Vadim)
* some other cleanups (various)
-----BEGIN PGP SIGNATURE-----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=wOaR
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-02-03' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Last round of updates for net-next:
* revert a patch that caused a regression with mesh userspace (Bob)
* fix a number of suspend/resume related races
(from Emmanuel, Luca and myself - we'll look at backporting later)
* add software implementations for new ciphers (Jouni)
* add a new ACPI ID for Broadcom's rfkill (Mika)
* allow using netns FD for wireless (Vadim)
* some other cleanups (various)
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When mac80211 disconnects, it drops all the packets on the
queues. This happens after the net stack has been notified
that we have no link anymore (netif_carrier_off).
netif_carrier_off ensures that no new packets are sent to
xmit() callback, but we might have older packets in the
middle of the Tx path. These packets will land in the
driver's queues after the latter have been flushed.
Synchronize_net() between netif_carrier_off and drv_flush()
will fix this.
Note that we can't call synchronize_net inside
ieee80211_flush_queues since there are flows that call
ieee80211_flush_queues and don't need synchronize_net()
which is an expensive operation.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[reword comment to be more accurate]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While suspending, we destroy the authentication /
association that might be taking place. While doing so, we
forgot to delete the timer which can be firing after
local->suspended is already set, producing the warning below.
Fix that by deleting the timer.
[66722.825487] WARNING: CPU: 2 PID: 5612 at net/mac80211/util.c:755 ieee80211_can_queue_work.isra.18+0x32/0x40 [mac80211]()
[66722.825487] queueing ieee80211 work while going to suspend
[66722.825529] CPU: 2 PID: 5612 Comm: kworker/u16:69 Tainted: G W O 3.16.1+ #24
[66722.825537] Workqueue: events_unbound async_run_entry_fn
[66722.825545] Call Trace:
[66722.825552] <IRQ> [<ffffffff817edbb2>] dump_stack+0x4d/0x66
[66722.825556] [<ffffffff81075cad>] warn_slowpath_common+0x7d/0xa0
[66722.825572] [<ffffffffa06b5b90>] ? ieee80211_sta_bcn_mon_timer+0x50/0x50 [mac80211]
[66722.825573] [<ffffffff81075d1c>] warn_slowpath_fmt+0x4c/0x50
[66722.825586] [<ffffffffa06977a2>] ieee80211_can_queue_work.isra.18+0x32/0x40 [mac80211]
[66722.825598] [<ffffffffa06977d5>] ieee80211_queue_work+0x25/0x50 [mac80211]
[66722.825611] [<ffffffffa06b5bac>] ieee80211_sta_timer+0x1c/0x20 [mac80211]
[66722.825614] [<ffffffff8108655a>] call_timer_fn+0x8a/0x300
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When roaming / suspending, it makes no sense to wait until
the transmit queues of the device are empty. In extreme
condition they can be starved (VO saturating the air), but
even in regular cases, it is pointless to delay the roaming
because the low level driver is trying to send packets to
an AP which is far away. We'd rather drop these packets and
let TCP retransmit if needed. This will allow to speed up
the roaming.
For suspend, the explanation is even more trivial.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge mac80211.git to get some changes that would otherwise
cause conflicts with new changes coming here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The return value should be initialized to false so that there's a
valid return value when there are no sessions that need work to be
done on them. Luckily, the side effect of using the uninitialized
value is an extra harmless driver call.
Coverity: CID 1260096
Fixes: 02219b3abc ("mac80211: add WMM admission control support")
Signed-off-by: John W. Linville <linville@tuxdriver.com>
[extend commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In beacons, handle the Country IE even if no Power Constraint IE
is present, and, capability wise, also in case that the Radio
Measurements capability is enabled.
In cases where the Country IE should be handled and that the
Power Constraint IE is not present, the Country IE alone will
set the power limit (and not both Country and Power Constraint
IEs).
Signed-off-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
HT override configurations was ignored when choosing the channel
(until now, the override configuration affected only the
capabilities shown in the IEs).
The override configurations received only on association time,
so in this case we should determine the channel again.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The call to cfg80211_ch_switch_notify() should be at the end of the
ieee80211_chswitch_post_beacon() function, because it should only be
sent if everything succeeded.
Fixes: d04b5ac9e7 ("cfg80211/mac80211: allow any interface to send channel switch notifications")
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to let drivers have more dynamic U-APSD support,
move the enablement flag to the virtual interface driver
flags. This lets drivers not only set it up differently
for different interfaces, but also enable/disable on the
fly if needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Thomas Pedersen