Assign proper FIMC-IS UART gate clock in the device DT node and not
use the SRC_MASK gate. This fixes regression introduced in commit
a37c82a3b3 ("clk: samsung: exynos4: Remove
SRC_MASK_ISP gates").
Without this change exynos4 fimc-is driver fails to probe with an
error log:
[ 1.842447] ERROR: could not get clock /camera/fimc-is@12000000:uart(13)
[ 1.848529] exynos4-fimc-is 12000000.fimc-is: failed to get clock: uart
[ 1.855275] exynos4-fimc-is: probe of 12000000.fimc-is failed with error -2
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add to Trats2 DTS new node for configuring the max77693 charger driver.
Only the maxim,constant-microvolt differs from default value but set all
of the optional properties anyway.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Remove fixed regulators (duplicating what max77686 provides) and
add GPIO enable control to max77686 regulators.
This gives the system full control over those regulators. Previously
the state of such regulators was a mixture of what max77686 driver set
over I2C and what regulator-fixed set through GPIO.
Removal of 'regulator-always-on' from CAM_ISP_CORE_1.2V (buck9) allows
disabling it when it is not used. Previously this regulator was always
enabled because its enable state is a OR of:
- ENB9 GPIO (turned always on by regulator-fixed),
- BUCK9EN field in BUCK9CTRL register (off by max77686 through I2C).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add suspend to RAM configuration for max77686 regulators. Some LDOs
and bucks are disabled. This reduces energy consumption during S2R,
approximately from 17 mA to 9 mA.
Additionally remove old and not supported bindings:
- regulator-mem-off
- regulator-mem-idle
- regulator-mem-on
The max77686 driver does not parse them and they are not documented
anywere.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add node for fuel gauge present in Maxim 77693 PMIC. This allows control
over battery charging state on Trats2 board.
The fuel gauge is compatible with max17042 battery driver (Maxim
17042/17047/17050). Although datasheet rev 2.2 for MAX77693 describes
fuel gauge as Maxim 17042-like, the chip on Trats2 board identifies
itself as Maxim 17047-like.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The charge delay value is by default 0x400. But it can be set to lower
values on some boards, as long as false pen-ups are avoided. Lowering the
value increases the sampling rate (though current sampling rate is
sufficient for TSC operation). In some boards, the value has to be
increased to avoid false pen-up events. Hence, charge delay has been
made a DT parameter.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit e1a5848e33 ("ARM: 7924/1: mm: don't bother with reserved ttbr0
when running with LPAE") removed the use of the reserved TTBR0 value
for LPAE systems, since the ASID is held in the TTBR and can be updated
atomicly with the pgd of the next mm.
Unfortunately, this patch forgot to update flush_context, which
deliberately avoids marking the local active ASID as allocated, since we
used to switch via ASID zero and didn't need to allocate the ASID of
the previous mm. The side-effect of this is that we can allocate the
same ASID to the next mm and, between flushing the local TLB and updating
TTBR0, we can perform speculative TLB fills for userspace nG mappings
using the page table of the previous mm.
The consequence of this is that the next mm can erroneously hit some
mappings of the previous mm. Note that this was made significantly
harder to hit by a391263cd8 ("ARM: 8203/1: mm: try to re-use old ASID
assignments following a rollover") but is still theoretically possible.
This patch fixes the problem by removing the code from flush_context
that forces the allocated ASID to zero for the local CPU. Many thanks
to the Broadcom guys for tracking this one down.
Fixes: e1a5848e33 ("ARM: 7924/1: mm: don't bother with reserved ttbr0 when running with LPAE")
Cc: <stable@vger.kernel.org> # v3.14+
Reported-by: Raymond Ngun <rngun@broadcom.com>
Tested-by: Raymond Ngun <rngun@broadcom.com>
Reviewed-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds a way for clock consumers to set maximum and minimum rates. This
can be used for thermal drivers to set minimum rates, or by misc.
drivers to set maximum rates to assure a minimum performance level.
Changes the signature of the determine_rate callback by adding the
parameters min_rate and max_rate.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[sboyd@codeaurora.org: set req_rate in __clk_init]
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: min/max rate for sun6i_ahb1_clk_determine_rate
migrated clk-private.h changes to clk.c]
Remove omap_clocks_register and dummy_ck. The former is not used anymore
now that the statically defined clk stuctures are replaced with proper
descriptors and registered with the framework.
The dummy clock in arch/arm/mach-omap2 is made redundant by the OMAP3+
clock data that migrated to drivers/clk.
An additional benefit to this clean-up is removing the references to
clk-private.h which will be removed.
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Moves clock state to struct clk_core, but takes care to change as little API as
possible.
struct clk_hw still has a pointer to a struct clk, which is the
implementation's per-user clk instance, for backwards compatibility.
The struct clk that clk_get_parent() returns isn't owned by the caller, but by
the clock implementation, so the former shouldn't call clk_put() on it.
Because some boards in mach-omap2 still register clocks statically, their clock
registration had to be updated to take into account that the clock information
is stored in struct clk_core now.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
[mturquette@linaro.org: adapted clk_has_parent to struct clk_core
applied OMAP3+ DPLL fix from Tero & Tony]
* pci/config:
PCI: xilinx: Convert to use generic config accessors
PCI: xgene: Convert to use generic config accessors
PCI: tegra: Convert to use generic config accessors
PCI: rcar: Convert to use generic config accessors
PCI: generic: Convert to use generic config accessors
powerpc/powermac: Convert PCI to use generic config accessors
powerpc/fsl_pci: Convert PCI to use generic config accessors
ARM: ks8695: Convert PCI to use generic config accessors
ARM: sa1100: Convert PCI to use generic config accessors
ARM: integrator: Convert PCI to use generic config accessors
ARM: cns3xxx: Convert PCI to use generic config accessors
PCI: Add generic config accessors
powerpc/PCI: Add struct pci_ops member names to initialization
mn10300/PCI: Add struct pci_ops member names to initialization
MIPS: PCI: Add struct pci_ops member names to initialization
frv/PCI: Add struct pci_ops member names to initialization
This patch adds stdout-path property to chosen nodes of Exynos4 boards
to enable use of earlycon feature without the need to hardcode port
number in kernel itself.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tegra_clocks_apply_init_table() needs to be called after the udelay
loop has been calibrated (see commit
441f199a37 ("clk: tegra: defer
application of init table") for why that is). On existing Tegra SoCs
this was done by calling tegra_clocks_apply_init_table() from
tegra_dt_init(). To make this also work on ARM64, we need to change
this into an initcall. tegra_dt_init() is called from
customize_machine which is an arch_initcall. Therefore this should
also work on existing 32bit Tegra SoCs.
Tested on Tegra20 (ventana), Tegra30 (beaverboard), Tegra124 (jetson TK1) and
Tegra132.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
[paul@pwsan.com: tweaked the commit message]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Remove the string "(Device Tree)" after the machine name because all AT91
machines use the DT nowadays.
Also change some function names to unify following the convention:
- at91sam9xxx aren't named sam9, 9xxx but with the full name
- sama5 are the ones that don't have the at91 prefix anymore.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Move the ramc initialization to pm.c as it is the only user left.
This allows us to get rid of at91_dt_initialize() that was the only one called
by the init_early() function pointer of struct machine_desc.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
[nicolas.ferre@atmel.com: adapt patch to newer series]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As board files are now DT only and can address all aspects of the SoC family,
we can rename them so that the mach-at91 directory looks cleaner.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
at91_boot_soc and at91_init_soc structures are not used by any SoC, remove
their use. Also remove all the now empty SoC files.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
[nicolas.ferre@atmel.com: different organization of the patches]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
For sama5d4, remove an indirection and the remaining need for at91_boot_soc
structure.
This will allow further cleanup.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Only use SOC_AT91SAM9 for all the at91sam9 SoCs. It removes all the empty
at91sam9xxx.c SoC files. It also removes the useless at91_init_soc affectation
procedure and its "init" function pointer.
Only the SoC detection and display are kept for the at91sam9:
at91_soc_is_enabled() and at91_boot_soc.map_io() function calls are also
removed.
It enables HAVE_AT91_SMD and HAVE_AT91_UTMI for all the sam9 SoCs but this only
represents 96 bytes of uncompressed kernel code.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
[nicolas.ferre@atmel.com: different organization of the patches]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Setup arm_pm_idle and arm_pm_restart function pointers from
rm9200_dt_device_init() function to simplify the at91rm9200 initialization
process.
This same move is already done for the sam9s.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
[nicolas.ferre@atmel.com: adapt patch to newer series]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
- several fixes and adjustments following the last cleanup batch
- removal of some unused Kconfig options
- slight PM and pm_idle rework to ease future rework
- removal of unneeded mach/system_rev.h
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUxjj9AAoJEAf03oE53VmQGEAH/3nLneCOQeyuq60adx+Lxcdn
Q9sMMzrw4B6bQnJee7+PQD3/QU7fmF8qNKlMKYAlILFHGNQplASi4uAfRTykUA0j
RQHpS9n20ODVfX+yePJ/o8h2r1BkT2wUIDXxaZCj2RoPmEz1aiFDNa2pPsUfprRd
gpbh+ZU43LRowYwH9UHPV55PQ0ZwMq3ry2DOYY5Al1+bKQ8TFvAdDMUu3rGZU7A4
dMYiQCQ6Fv0EI1NY0IHSf/u/jujlPE2H0TSR38w8lYfIPzBx2tHkLSupuxKh7R1N
QYibgZXWR0PqHOXMpOHYBqJFj5c3f/aOZ/dO4RJha+S7YHNQnIFzLsm122njgKQ=
=KgUm
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup3' into at91-3.20-soc
One more week's worth of fixes. Worth pointing out here are:
- A patch fixing detaching of iommu registrations when a device is removed --
earlier the ops pointer wasn't managed properly
- Another set of Renesas boards get the same GIC setup fixup as others have in
previous -rcs
- Serial port aliases fixups for sunxi. We did the same to tegra but we
caught that in time before the merge window due to more machines being
affected. Here it took longer for anyone to notice.
- A couple more DT tweaks on sunxi
- A follow-up patch for the mvebu coherency disabling in last -rc batch
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nw2v
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"One more week's worth of fixes. Worth pointing out here are:
- A patch fixing detaching of iommu registrations when a device is
removed -- earlier the ops pointer wasn't managed properly
- Another set of Renesas boards get the same GIC setup fixup as
others have in previous -rcs
- Serial port aliases fixups for sunxi. We did the same to tegra but
we caught that in time before the merge window due to more machines
being affected. Here it took longer for anyone to notice.
- A couple more DT tweaks on sunxi
- A follow-up patch for the mvebu coherency disabling in last -rc
batch"
* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm: dma-mapping: Set DMA IOMMU ops in arm_iommu_attach_device()
ARM: shmobile: r8a7790: Instantiate GIC from C board code in legacy builds
ARM: shmobile: r8a73a4: Instantiate GIC from C board code in legacy builds
ARM: mvebu: don't set the PL310 in I/O coherency mode when I/O coherency is disabled
ARM: sunxi: dt: Fix aliases
ARM: dts: sun4i: Add simplefb node with de_fe0-de_be0-lcd0-hdmi pipeline
ARM: dts: sun6i: ippo-q8h-v5: Fix serial0 alias
ARM: dts: sunxi: Fix usb-phy support for sun4i/sun5i
* Instantiate GIC from C board code in legacy builds on r8a7790 and r8a73a4
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/Oq9
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-fixes3-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Merge "Third Round of Renesas ARM Based SoC Fixes for v3.19" from Simon Horman:
* Instantiate GIC from C board code in legacy builds on r8a7790 and r8a73a4
* tag 'renesas-soc-fixes3-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790: Instantiate GIC from C board code in legacy builds
ARM: shmobile: r8a73a4: Instantiate GIC from C board code in legacy builds
Signed-off-by: Olof Johansson <olof@lixom.net>
Looks like on 3517 davinci_emac MAC address registers have a
different layout compared to dm816x and am33xx.
Let's add a function to get the 3517 MAC address.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On this board USB2 is meant to be used as peripheral only.
The ID pin for USB2 is hardwired HIGH.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On this EVM, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).
NOTE: the ports on this board cannot switch roles. They are
configured either host or peripheral by hardwiring the
respective ID pins.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On this EVM, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).
Gets USB peripheral mode to work on this EVM.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On this EVM, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).
Gets USB peripheral mode to work on this EVM.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert the ks8695 PCI driver to use the generic config access functions.
This changes accesses from __raw_readX/__raw_writeX to readX/writeX
variants.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: linux-arm-kernel@lists.infradead.org
Convert the sa1100 nanoengine PCI driver to use the generic config access
functions.
Change accesses from __raw_readX/__raw_writeX to readX/writeX variants.
This removes the spinlock because it is unnecessary. The config read and
write functions are already protected with a spinlock.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: linux-arm-kernel@lists.infradead.org
This is no longer used for anything, thus it can be removed.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
As the clock data is now available for the legacy boot also from the
clock driver, use this rather than the data under the mach folder.
This allows us to get rid of the old clock data completely.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
As the legacy clock data is being moved under clock driver, the
clock data will be using the same low level infrastructure for
register accesses. This requires the clk_memmaps to be initialized
properly. This patch adds a support hook to the PRM driver to
initialize the mappings.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
for x86 (bug introduced in 3.19).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJUy2ulAAoJEL/70l94x66D18kIAJhuh2k5Mt3TfP/zfhi2Y6ER
IAZqyFODs8txZ3v432PB8yWWvr2XfJ3gwfjvurLygQJ3jCGZqDrmucbUUXzEaPUk
mPnLpxV0ZEmNweS2HLGPX9HJ6zfsZ1dHRk55Tko9ynAO731q7yPjj6HC0th8wzvE
BRv5y/18rY2zyar+5Azpj5wpOSllq0ynMgjWXGSlaTLbQoyvgZtzbqNY6nsAGrKw
e8hSUPogfGUmZkBHHHVDYKpgHvWS1hARyuGFo8LeKXKPo7qhYxZHCDpch8TXnq2y
21IvQfYddGpcMsaTroA5qyXFigxCX+1j3po6MS3ZH9GGXS5fC3sI8t0EDxKiO6Q=
=O4X0
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"The ARM changes are largish, but not too scary. And a simple fix for
x86 (bug introduced in 3.19)"
(Paolo sayus these are the "Final" fixes. We'll see).
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: check LAPIC presence when building apic_map
arm/arm64: KVM: Use kernel mapping to perform invalidation on page fault
arm/arm64: KVM: Invalidate data cache on unmap
arm/arm64: KVM: Use set/way op trapping to track the state of the caches
Fixes memory corruption issues on APM platforms and swapping issues on
DMA-coherent systems.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUyrVCAAoJEEtpOizt6ddy/rgH/1gFfX3zGryDYwbFz2BbnMk8
zJeQfeaOD4TF/6k8UZctrJatoqPgMCmVMAbT7uuZ+zwOYPYDGijGeJOYKS6IcIcj
Lhl0QjbwBUaC58jZhhKGStZTKV2w9L7JK3RFStw+cE2HAAKcZQSVdfnM7ZoyyaRC
qbFqPXLppSSZXD1R+/F17+mM8bogRmdS4we0o7J1KCT6hWbnK1CJkScxXLapbl5Y
tKZSMM+k+L7wvgDnuzepTY+rFna3LSLQXNli0nPX9ByRFR4nMjeJKwm68kOaTU1r
y1naOS3F6kl7S0OiCzyzekM4U330MAVmTyvlT9GHAHCVyjzavGQuuBFHdcdnvvc=
=rJUG
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-fixes-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master
Second round of fixes for KVM/ARM for 3.19.
Fixes memory corruption issues on APM platforms and swapping issues on
DMA-coherent systems.
The following patch adds coupled cpuidle support for Exynos4210 to
an existing cpuidle-exynos driver. As a result it enables AFTR mode
to be used by default on Exynos4210 without the need to hot unplug
CPU1 first.
The patch is heavily based on earlier cpuidle-exynos4210 driver from
Daniel Lezcano:
http://www.spinics.net/lists/linux-samsung-soc/msg28134.html
Changes from Daniel's code include:
- porting code to current kernels
- fixing it to work on my setup (by using S5P_INFORM register
instead of S5P_VA_SYSRAM one on Revison 1.1 and retrying poking
CPU1 out of the BOOT ROM if necessary)
- fixing rare lockup caused by waiting for CPU1 to get stuck in
the BOOT ROM (CPU hotplug code in arch/arm/mach-exynos/platsmp.c
doesn't require this and works fine)
- moving Exynos specific code to arch/arm/mach-exynos/pm.c
- using cpu_boot_reg_base() helper instead of BOOT_VECTOR macro
- using exynos_cpu_*() helpers instead of accessing registers
directly
- using arch_send_wakeup_ipi_mask() instead of dsb_sev()
(this matches CPU hotplug code in arch/arm/mach-exynos/platsmp.c)
- integrating separate exynos4210-cpuidle driver into existing
exynos-cpuidle one
Cc: Colin Cross <ccross@google.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Commit c2dd114d24 ("ARM: EXYNOS: fix register setup for AFTR mode
code") added S5P_CENTRAL_SEQ_OPTION register setup fix for all
Exynos SoCs to AFTR mode code-path. It turned out that for coupled
cpuidle AFTR mode on Exynos4210 (added by the next patch) applying
this fix causes lockup so enable it in the AFTR mode code-path only
on SoCs that require it (in the suspend code-path it can be always
applied like it was before commit c2dd114d24 ("ARM: EXYNOS: fix
register setup for AFTR mode code")
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Colin Cross <ccross@google.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Currently the hdmi driver is using one of the soc i2c busses for ddc probing
and while documentation always specifies i2c5 as hdmi-i2c it could very well
be any other bus as well.
Therefore this is a property of the board and should be specified there.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This enables the recently added display nodes on the firefly and evb,
letting the boards output graphic data over the hdmi port.
This includes enabling of i2c5 on the evb that is used for ddc probing and
setting the lcd-regulators to always on until the hdmi driver learns
about using them.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
When handling a fault in stage-2, we need to resync I$ and D$, just
to be sure we don't leave any old cache line behind.
That's very good, except that we do so using the *user* address.
Under heavy load (swapping like crazy), we may end up in a situation
where the page gets mapped in stage-2 while being unmapped from
userspace by another CPU.
At that point, the DC/IC instructions can generate a fault, which
we handle with kvm->mmu_lock held. The box quickly deadlocks, user
is unhappy.
Instead, perform this invalidation through the kernel mapping,
which is guaranteed to be present. The box is much happier, and so
am I.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Let's assume a guest has created an uncached mapping, and written
to that page. Let's also assume that the host uses a cache-coherent
IO subsystem. Let's finally assume that the host is under memory
pressure and starts to swap things out.
Before this "uncached" page is evicted, we need to make sure
we invalidate potential speculated, clean cache lines that are
sitting there, or the IO subsystem is going to swap out the
cached view, loosing the data that has been written directly
into memory.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Trying to emulate the behaviour of set/way cache ops is fairly
pointless, as there are too many ways we can end-up missing stuff.
Also, there is some system caches out there that simply ignore
set/way operations.
So instead of trying to implement them, let's convert it to VA ops,
and use them as a way to re-enable the trapping of VM ops. That way,
we can detect the point when the MMU/caches are turned off, and do
a full VM flush (which is what the guest was trying to do anyway).
This allows a 32bit zImage to boot on the APM thingy, and will
probably help bootloaders in general.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Use the same transfer speed on both the rk808 and act8846 variants and
remove the status=okay from the rk808 one which is already set in the
shared rk3288-evb.dtsi .
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The evaluation board using the act8846 as main pmic uses two additional
regulators to provide the cpu and gpu voltage. Add these and also add
the link to cpu supply from vdd_cpu.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
* Select CONFIG_REGULATOR in mach_shmobile defconfig once again
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=joof
-----END PGP SIGNATURE-----
Merge tag 'renesas-defconfig-fixes-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/defconfig
Merge "Renesas ARM Based SoC Defconfig Fixes for v3.20" from Simon Horman:
* Select CONFIG_REGULATOR in mach_shmobile defconfig once again
* tag 'renesas-defconfig-fixes-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Select CONFIG_REGULATOR in defconfig once again
Signed-off-by: Olof Johansson <olof@lixom.net>
- add DISP1 power domain for support HDMI support on exynos5420/5422/5800
and the power domain node including FIMD1, MIXER and HDMI modules
(tested on exynos5420 Peach Pit and exynos5800 Peach Pi Chromebooks
and exynos5422 Odroid XU3 by Javier Martinez Canillas)
Note this is including a patch for adding clock IDs for the DISP1 power
domain with Mike and Sylwester's acks so that could be handled together
to avoid non-working.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9Imn
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung 3rd DT updates for v3.20" from Kukjin Kim:
- add DISP1 power domain for support HDMI support on exynos5420/5422/5800
and the power domain node including FIMD1, MIXER and HDMI modules
(tested on exynos5420 Peach Pit and exynos5800 Peach Pi Chromebooks
and exynos5422 Odroid XU3 by Javier Martinez Canillas)
Note this is including a patch for adding clock IDs for the DISP1 power
domain with Mike and Sylwester's acks so that could be handled together
to avoid non-working.
* tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add DISP1 power domain for exynos5420
clk: exynos5420: Add IDs for clocks used in DISP1 power domain
Signed-off-by: Olof Johansson <olof@lixom.net>
- for all of Samsung SoCs
: use generic power domain bindings
: add 'dr_mode' property for hsotg/dwc2 devices
- exynos3250-rinato and exynos3250-monk
: add regulator-haptic
- exynos5422-odroidxu3
: reduce total RAM by 22 MiB because last 22 MiB
for secure monitor cannot be accessed by kernel
: add on-board INA231 sensors and LDO26 of PMIC
for the sensors
Note that this is based on tags/samsung-dt
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=DGVz
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung 2nd DT updates for v3.20" from Kukjin Kim:
- for all of Samsung SoCs
: use generic power domain bindings
: add 'dr_mode' property for hsotg/dwc2 devices
- exynos3250-rinato and exynos3250-monk
: add regulator-haptic
- exynos5422-odroidxu3
: reduce total RAM by 22 MiB because last 22 MiB
for secure monitor cannot be accessed by kernel
: add on-board INA231 sensors and LDO26 of PMIC
for the sensors
* tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: reduce total RAM by 22 MiB for exynos5422-odroidxu3
ARM: dts: add on-board INA231 sensors for exynos5422-odroidxu3
ARM: dts: Add regulator-haptic node for exynos3250-monk
ARM: dts: Add regulator-haptic node for exynos3250-rinato
ARM: dts: add 'dr_mode' property to hsotg devices for exynos boards
ARM: dts: convert to generic power domain bindings for exynos DT
Signed-off-by: Olof Johansson <olof@lixom.net>
- add exynos3250 Supsend to RAM support
- recognize MFC v8 devices for exynos5422/5800
- print CPU id/rev during kernel boot
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=MZnm
-----END PGP SIGNATURE-----
Merge tag 'samsung-update' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
Merge "Samsung mach updates for v3.20" from Kukjin Kim:
- add exynos3250 Supsend to RAM support
- recognize MFC v8 devices for exynos5422/5800
- print CPU id/rev during kernel boot
* tag 'samsung-update' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Add exynos3250 suspend-to-ram support
ARM: EXYNOS: Recognize Samsung MFC v8 devices
ARM: SAMSUNG: print CPU id on probe
Signed-off-by: Olof Johansson <olof@lixom.net>
- remove i2c sys configuration from mach-exynos/
: all related codes moved into i2c driver
- remove Samsung specific DMA
: every Samsung stuff uses dmaengine APIs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJUyXM3AAoJEA0Cl+kVi2xqn8MP/jDl9Jgx94dvLoj+jZxrN/QL
qm4ZbhWnQ+DCv6B8GSgkwljWTpQazqUztft1FXpjKUW3p2VoQHugb0a62jySx6vG
VKCxLsZh95Zj7ZL1q18v1HO7zrAm/TdWl7H+j55jATfQVQGmHeiFTkyHBYVmicHU
/HMwT3C42oJEiz58BPs0uoM5Pfm+2cV8J4yj2VMIQXLx5y52+Ic0s228yJxqWYuO
Nm7RGMW5oJwkgAli2ug0VqMUYGVg4otiNqoXIl9DP1B+yhdvEsXrkPcDNvTqgJBU
nq+ho3X2qFM+ETMi80QA4YNq/MM5Ns3cqwMprVTeAvMe8xJqjL3FpSc3eDQRRhHq
LHn0eUhwOj4xWa5d/dku6Onp1UOBSqvuURj30Vg2OXMwwBa/DD5g3sihmvBXUdVa
Bd8QEWl9gcVTXqjRb3V2X9UdID3EZMongAohzAqi/ailb8kFmdGPOt7EZsPGa4ZA
YkxR/KvcLMEjClwGVDH9x7vJq8rONSi+zWhE3MbBMjyj4quUv4tzMUb2Bl2dkrma
lrpberjceQ2gLIRFC8fy5JoL4sNfIT3JcCpLCRMZXK9SbWx7UjdV3Ni8m04ldwJt
+Jjoh2qiZ/wsFH++RyJ2K3yrntcGhzqe/wfm1ZB6dGe0W/XRIOb/dq9vBODbX/9W
yl99BuYWxUZw9aHPfRp2
=2/ZU
-----END PGP SIGNATURE-----
Merge tag 'samsung-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup
Merge "Samsung cleanup for v3.20" from Kukjin Kim:
- remove i2c sys configuration from mach-exynos/
: all related codes moved into i2c driver
- remove Samsung specific DMA
: every Samsung stuff uses dmaengine APIs
* tag 'samsung-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: remove unused DMA infrastructure
ARM: EXYNOS: Remove i2c sys configuration related code
Signed-off-by: Olof Johansson <olof@lixom.net>
The digicolor interrupt controller driver now needs syscon.
Also, as per clocksource maintainer request, we now have a separate config
symbol, CONFIG_DIGICOLOR_TIMER, for the digicolor timer.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit 4bb25789ed ("arm: dma-mapping: plumb our iommu mapping ops
into arch_setup_dma_ops") moved the setting of the DMA operations from
arm_iommu_attach_device() to arch_setup_dma_ops() where the DMA
operations to be used are selected based on whether the device is
connected to an IOMMU. However, the IOMMU detection scheme requires the
IOMMU driver to be ported to the new IOMMU of_xlate API. As no driver
has been ported yet, this effectively breaks all IOMMU ARM users that
depend on the IOMMU being handled transparently by the DMA mapping API.
Fix this by restoring the setting of DMA IOMMU ops in
arm_iommu_attach_device() and splitting the rest of the function into a
new internal __arm_iommu_attach_device() function, called by
arch_setup_dma_ops().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
When using network driver on keystone and nfs rootfs is used following
error displayed and device halts.
Missing devtmpfs, which is required for udev to run
Halting...
Add the DEVTMPFS option by default to fix this
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
StrongARM core uses RCSR SMR bit to tell to bootloader that it was reset
by entering the sleep mode. After we have resumed, there is little point
in having that bit enabled. Moreover, if this bit is set before reboot,
the bootloader can become confused. Thus clear the SMR bit on resume
just before clearing the scratchpad (resume address) register.
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Let kernel drivers to control wakeup sources instead of hardcoding them
in the collie.c board file.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use handle_domain_irq instead of handle_IRQ to automatically map
hardware irq number to virq.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As a part of driver consolidation, move GPIO-related IRQ code to
drivers/gpio/gpio-sa1100.c. The code does not use GPIOLIB_IRQCHIP (yet),
because sa1100 does not have a device for gpios, which is a requirement
for GPIOLIB_IRQCHIP. This will be the next step.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As now both SC and GPIO irq domains start from 0 hwirq and do not
contain holes, switch to using irq_domain_add_simple() instead of
irq_domain_add_legacy().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now there is no difference between low and high GPIO irqdomains. Merge
them into single irqdomain handling all GPIOs.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Low GPIO pins use an interrupt in SC interrupts space. However it's
possible to handle them as if all the GPIO interrupts are instead tied
to single GPIO handler, which later decodes GEDR register and
chain-calls next IRQ handler. So split first 11 interrupts into system
part (IRQ_GPIO0_SC - IRQ_GPIO10_SC) which work exactly like the rest of
system controller interrupts and real GPIO interrupts
(IRQ_GPIO0..IRQ_GPIO10). A single handler sa1100_gpio_handler then
decodes and calls next handler.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The recently added ARM_KERNMEM_PERMS feature works by manipulating
the kernel page tables, which obviously requires an MMU. Trying
to enable this feature when the MMU is disabled results in a lot
of compile errors in mm/init.c, so let's add a Kconfig dependency
to avoid that case.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Minimal builds for v7M are broken when printk is disabled. The caller is
assembly so add the necessary ifdef around the call.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is currently a hardcoded limit of 64KB for the DTB to live in and
be extended with ATAG info. Some DTBs have outgrown that limit:
$ du -b arch/arm/boot/dts/omap3-n900.dtb
70212 arch/arm/boot/dts/omap3-n900.dtb
Furthermore, the actual size passed to atags_to_fdt() included the stack
size which is obviously wrong.
The initial DTB size is known, so use it to size the allocated workspace
with a 50% growth assumption and relocate the temporary stack above that.
This is also clamped to 32KB min / 1MB max for robustness against bad
DTB data.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When tearing down the DMA ops for a device via of_dma_deconfigure, we
unconditionally detach the device from its IOMMU domain. For devices
that aren't actually behind an IOMMU, this produces a "Not attached"
warning message on the console.
This patch changes the teardown code so that we don't detach from the
IOMMU domain when there isn't an IOMMU dma mapping to start with.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Based on
"mfd: syscon: Decouple syscon interface from platform devices"
(sha1: bdb0066df9)
SLCR driver can use syscon/regmap drivers directly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Convert the integrator PCI driver to use the generic config access
functions.
This changes accesses from __raw_readX/__raw_writeX to readX/writeX
variants. The spinlock is removed because it is unnecessary. The config
read and write functions are already protected with a spinlock and no
access can occur during the .pre_init function.
[arnd: remove unused "flags"]
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: linux-arm-kernel@lists.infradead.org
Add the PCI controller node for the Versatile/PB board.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
CC: Russell King <linux@arm.linux.org.uk>
We don't have to write protect guest memory for dirty logging if architecture
supports hardware dirty logging, such as PML on VMX, so rename it to be more
generic.
Signed-off-by: Kai Huang <kai.huang@linux.intel.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The Versatile boards have the same sysregs as other ARM Ltd boards. Add
the nodes in order to enable support for 24MHz counter as sched_clock.
This is a minimal node definition as the existing sub node definition
used on VExpress has some issues raised by Linus W.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The rk3288 board uses the architected timers and these ones are shutdown when
the cpu is powered down. There is a need of a broadcast timer in this case to
ensure proper wakeup when the cpus are in sleep mode and a timer expires.
This driver provides the basic timer functionnality as a backup for the local
timers at sleep time.
The timer belongs to the alive subsystem. It includes two programmables 64 bits
timer channels but the driver only uses 32bits. It works with two operations
mode: free running and user defined count.
Programing sequence:
1. Timer initialization:
* Disable the timer by writing '0' to the CONTROLREG register
* Program the timer mode by writing the mode to the CONTROLREG register
* Set the interrupt mask
2. Setting the count value:
* Load the count value to the registers COUNT0 and COUNT1 (not used).
3. Enable the timer
* Write '1' to the CONTROLREG register with the mode (free running or user)
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
As of commit 9a1091ef00 ("irqchip: gic: Support hierarchy irq
domain."), the Lager legacy board support is known to be broken.
The IRQ numbers of the GIC are now virtual, and no longer match the
hardcoded hardware IRQ numbers in the legacy platform board code.
To fix this issue specific to non-multiplatform r8a7790 and Lager:
1) Instantiate the GIC from platform board code and also
2) Skip over the DT arch timer as well as
3) Force delay setup based on DT CPU frequency
With these 3 fixes in place interrupts on Lager are now unbroken.
Partially based on legacy GIC fix by Geert Uytterhoeven, thanks to
him for the initial work.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit 9a1091ef00 ("irqchip: gic: Support hierarchy irq
domain."), the APE6EVM legacy board support is known to be broken.
The IRQ numbers of the GIC are now virtual, and no longer match the
hardcoded hardware IRQ numbers in the legacy platform board code.
To fix this issue specific to non-muliplatform r8a73a4 and APE6EVM:
1) Instantiate the GIC from platform board code and also
2) Skip over the DT arch timer as well as
3) Force delay setup based on DT CPU frequency
With these 3 fixes in place interrupts on APE6EVM are now unbroken.
Partially based on legacy GIC fix by Geert Uytterhoeven, thanks to
him for the initial work.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The DISP1 power domain on Exynos5420 SoC includes the FIMD1, MIXER
and HDMI modules. Add a device node for this power domain and mark
these modules as consumer of the DISP1 power domain.
When a power domain is powered on and off, the input clocks of the
devices attached to it are reparented. So a reference to the input
and parent clocks of the devices are needed to manage that.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
375/38x. Only switch the PL310 to I/O coherent mode if I/O coherency
is enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qzYQ
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-3.19-6' of git://git.infradead.org/linux-mvebu into fixes
Merge "mvebu-fixes-6" from Andrew Lunn:
The previous fix for Armada XP, disabling I/O coherency, broke Armada
375/38x. Only switch the PL310 to I/O coherent mode if I/O coherency
is enabled.
* tag 'mvebu-fixes-3.19-6' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: don't set the PL310 in I/O coherency mode when I/O coherency is disabled
Signed-off-by: Olof Johansson <olof@lixom.net>
The Exynos5420 cluster power management support allowing Exynos
5420/5422/5800 machines to power up and down the secondary CPUs.
Without this option enabled, the secondary CPUs are not brought
up on boot and the following error is shown:
CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
Setting up static identity map for 0x40938e90 - 0x40938f28
ARM CCI driver probed
CPU1: failed to boot: -38
CPU2: failed to boot: -38
CPU3: failed to boot: -38
CPU4: failed to boot: -38
CPU5: failed to boot: -38
CPU6: failed to boot: -38
CPU7: failed to boot: -38
Brought up 1 CPUs
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Olof Johansson <olof@lixom.net>
Since commit f2c3c67f00 (merge commit that adds commit "ARM: mvebu:
completely disable hardware I/O coherency"), we disable I/O coherency
on Armada EBU platforms.
However, we continue to initialize the coherency fabric, because this
coherency fabric is needed on Armada XP for inter-CPU
coherency. Unfortunately, due to this, we also continued to execute
the coherency fabric initialization code for Armada 375/38x, which
switched the PL310 into I/O coherent mode. This has the effect of
disabling the outer cache sync operation: this is needed when I/O
coherency is enabled to work around a PCIe/L2 deadlock. But obviously,
when I/O coherency is disabled, having the outer cache sync operation
is crucial.
Therefore, this commit fixes the armada_375_380_coherency_init() so
that the PL310 is switched to I/O coherent mode only if I/O coherency
is enabled.
Without this fix, all devices using DMA are broken on Armada 375/38x.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: <stable@vger.kernel.org> # v3.8+
Looks like I only got half done with moving pinctrl and syscon to
be children of the SCM. I've set up the FAPLL clocks that way already,
but did not complete the job as I copied the syscon values from
am33xx.dtsi.
To make sure the syscon mapping works, I've verfified that we can
set up davinci_emac mac address the same way as cpsw already does
with the syscon mapping. So let's add that too.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In one pinctrl node, a 'bias-disable' property is erroneously assigned a
value.
Fixes: ARM: zynq: DT: Add pinctrl information
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When unmapping grants, instead of converting the kernel map ops to
unmap ops on the fly, pre-populate the set of unmap ops.
This allows the grant unmap for the kernel mappings to be trivially
batched in the future.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Add the clock property for the watchdog on rk3288 socs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
for the broadcast timer going through the clocksource tree
and two new boards, the rk3288-based Firefly and the
PX2-based Rayeager board (the PX2 is identical to the rk3066
but made for industrial users).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJUyCaJAAoJEPOmecmc0R2By0oH/ioVbVZWYgTWJRlN0Cmjj+yr
fNnzm93g9N+Uk5PGOjCw70h3QSS65OLdqPF9xJwkSS1p7ORbKmOU3fzAET7x/EYK
a3Ct4NRPPiSkY12Qg+N4Q9wjz8sgUUHsLSFa5D/QJsyPu+lTVhLgWS4j4mzVCbyz
PSMn4Tx52OHzLHWKGrnEq33AIMROvarBmOgnvGe7AbutwDYqoiFiPALIAowrp/SR
WY689+3Gjtha5epUHn9vgUkNABnf0gXR1MBBJ1ZMxgForjZqeSCioHNYomneKOZC
9zyg4yuv5kNL75PY4aHLwalRfIFrqNM5S5D3gH7CTQg1/TcfUcVCBY0CAKczLxw=
=nDW6
-----END PGP SIGNATURE-----
Merge tag 'v3.20-rockchip-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "ARM: rockchip: second batch of dts updates for 3.20" from Heiko Stübner:
Basic display nodes for crtcs and hdmi encoder, timer node
for the broadcast timer going through the clocksource tree
and two new boards, the rk3288-based Firefly and the
PX2-based Rayeager board (the PX2 is identical to the rk3066
but made for industrial users).
* tag 'v3.20-rockchip-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add dts for ChipSPARK Rayeager PX2 board
ARM: dts: rockchip: add dts for Firefly Firefly-RK3288 boards
dt-bindings: add vendor prefix and root compatible property for Rockchip boards
ARM: dts: rockchip: Add rockchip timer node for rk3288
ARM: dts: rockchip: add rk3288 hdmi nodes
ARM: dts: rockchip: Add rk3288 vop and display-subsystem
Signed-off-by: Olof Johansson <olof@lixom.net>
Use the USART peripheral as UART for low level debug. Only the UA0 port is
currently supported.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add initial support for the Conexant CX92755 SoC. The CX92755 is one of the
Digicolor series of SoCs, all sharing many of the same peripherals. The code
was tested on the CX92755 evaluation kit, AKA Equinox.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit "ARM: pxa: arbitrarily set first interrupt number" broke viper
and zeus boards which still refer to PXA_ISA_IRQ() macro. Redefine
the macro, which declares the legacy interrupts from 0 to 15.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull networking fixes from David Miller:
1) Don't OOPS on socket AIO, from Christoph Hellwig.
2) Scheduled scans should be aborted upon RFKILL, from Emmanuel
Grumbach.
3) Fix sleep in atomic context in kvaser_usb, from Ahmed S Darwish.
4) Fix RCU locking across copy_to_user() in bpf code, from Alexei
Starovoitov.
5) Lots of crash, memory leak, short TX packet et al bug fixes in
sh_eth from Ben Hutchings.
6) Fix memory corruption in SCTP wrt. INIT collitions, from Daniel
Borkmann.
7) Fix return value logic for poll handlers in netxen, enic, and bnx2x.
From Eric Dumazet and Govindarajulu Varadarajan.
8) Header length calculation fix in mac80211 from Fred Chou.
9) mv643xx_eth doesn't handle highmem correctly in non-TSO code paths.
From Ezequiel Garcia.
10) udp_diag has bogus logic in it's hash chain skipping, copy same fix
tcp diag used. From Herbert Xu.
11) amd-xgbe programs wrong rx flow control register, from Thomas
Lendacky.
12) Fix race leading to use after free in ping receive path, from Subash
Abhinov Kasiviswanathan.
13) Cache redirect routes otherwise we can get a heavy backlog of rcu
jobs liberating DST_NOCACHE entries. From Hannes Frederic Sowa.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (48 commits)
net: don't OOPS on socket aio
stmmac: prevent probe drivers to crash kernel
bnx2x: fix napi poll return value for repoll
ipv6: replacing a rt6_info needs to purge possible propagated rt6_infos too
sh_eth: Fix DMA-API usage for RX buffers
sh_eth: Check for DMA mapping errors on transmit
sh_eth: Ensure DMA engines are stopped before freeing buffers
sh_eth: Remove RX overflow log messages
ping: Fix race in free in receive path
udp_diag: Fix socket skipping within chain
can: kvaser_usb: Fix state handling upon BUS_ERROR events
can: kvaser_usb: Retry the first bulk transfer on -ETIMEDOUT
can: kvaser_usb: Send correct context to URB completion
can: kvaser_usb: Do not sleep in atomic context
ipv4: try to cache dst_entries which would cause a redirect
samples: bpf: relax test_maps check
bpf: rcu lock must not be held when calling copy_to_user()
net: sctp: fix slab corruption from use after free on INIT collisions
net: mv643xx_eth: Fix highmem support in non-TSO egress path
sh_eth: Fix serialisation of interrupt disable with interrupt & NAPI handlers
...
data to make dm816x boot with basic devices. This finally gets
dm816x into a usable shape for further work to happen after a few
years of stalled effort of making this SoC to work with the mainline
kernel.
As most of the devices are similar to the other omap variants, we
get at least serial, MMC, Ethernet, I2C, EDMA, pinctrl, SPI and GPMC
working for these SoCs with the related device tree changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tGOy
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.20/dm816x-data' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Merge "omap changes to make dm816x usable" from Tony Lindgren:
Patches to add necessary SoC related clockdomain and interconnect
data to make dm816x boot with basic devices. This finally gets
dm816x into a usable shape for further work to happen after a few
years of stalled effort of making this SoC to work with the mainline
kernel.
As most of the devices are similar to the other omap variants, we
get at least serial, MMC, Ethernet, I2C, EDMA, pinctrl, SPI and GPMC
working for these SoCs with the related device tree changes.
* tag 'omap-for-v3.20/dm816x-data' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Add dm816x hwmod support
ARM: OMAP2+: Add clock domain support for dm816x
ARM: OMAP2+: Add board-generic.c entry for ti81xx
ARM: OMAP2+: Disable omap3 PM init for ti81xx
ARM: OMAP2+: Fix reboot for 81xx
ARM: OMAP2+: Fix dm814 and dm816 for clocks and timer init
ARM: OMAP2+: Fix ti81xx class type
ARM: OMAP2+: Fix ti81xx devtype
ARM: OMAP2+: Fix error handling for omap2_clk_enable_init_clocks
Signed-off-by: Olof Johansson <olof@lixom.net>
First set of OMAP2+ hwmod patches for Linux v3.20. These are mostly
fixes for warnings, although there's one DRA7xx patch that fixes
CONFIG_DEBUG_LL for AM572x/DRA7xx SoCs that use UART3 for console,
such as the BeagleBoard-X15.
These patches entered Linux-next starting with the next-20150121 tag.
Basic build, boot, and PM test results can be found here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v3.20/20150121142621/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2Zfx
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.20/fixes-not-urgent-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Merge "omap non-urgent fixes for v3.20, part 2" from Tony Lindgren:
Non-critical fixes for omap hwmod code via Paul Walmsley <paul@pwsan.com>:
First set of OMAP2+ hwmod patches for Linux v3.20. These are mostly
fixes for warnings, although there's one DRA7xx patch that fixes
CONFIG_DEBUG_LL for AM572x/DRA7xx SoCs that use UART3 for console,
such as the BeagleBoard-X15.
These patches entered Linux-next starting with the next-20150121 tag.
Basic build, boot, and PM test results can be found here:
http://www.pwsan.com/omap/testlogs/omap-hwmod-a-for-v3.20/20150121142621/
* tag 'omap-for-v3.20/fixes-not-urgent-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL enabled on UART3
ARM: OMAP: DRA7: hwmod: Make gpmc software supervised as the smart idle is broken
ARM: AM43xx: hwmod: set DSS submodule parent hwmods
ARM: OMAP2+: hwmod: print error if wait_target_ready() failed
MAINTAINERS: add maintainer for OMAP hwmod data
Signed-off-by: Olof Johansson <olof@lixom.net>
- correct some pin configuration for at91sam9x5ek
- add pioD on sama5d4 following a modification of pinctrl driver
- add more precise nand compatibility string for sama5d4
- audio modifications for wm8904 or ac97
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUxmgWAAoJEAf03oE53VmQtCoIAJtnUtvW5DqRWWsAzKxv6tPF
FLXihD9MRPyywgN5hDvNInKibqcBNxnLfk0xiFbCbfZXU4u6SK1E5iJN72mkTxhP
6rC/rdMDqMqGK7W43h4xFFpQdPrrq00t36gGvnQ+IUaOYcGAByJPYB3YwKMv/n0x
xHTPhydb2RPphEd9ZaXsbUKcaOJPG/6uChQSTp+8L0MAlh4cQADya1SapDhRefDa
PFz49N8QIjxgjWyJiWorcD8KH8hkGzLtvuvDl3UWkNZz9i3h7Vl3QaraC3HCHqwm
kJrOJ/EVw1uJKAKtYoo9xfoA8Z5HHno3vcQ4gKq4ylYDHIB3P4UhQLaGlcqkZfk=
=yOLr
-----END PGP SIGNATURE-----
Merge tag 'at91-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
Merge "at91: dt for 3.20 #2" from Nicolas Ferre:
Second DT batch for 3.20:
- correct some pin configuration for at91sam9x5ek
- add pioD on sama5d4 following a modification of pinctrl driver
- add more precise nand compatibility string for sama5d4
- audio modifications for wm8904 or ac97
* tag 'at91-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: sam9263: Add ac97 device node
dt: atmel_ac97c: Add device tree documentation
ARM: at91: at91sam9n12ek/dt: use dt ids for wm8904
ARM: at91: sama5d3xek/dt: use dt ids for wm8904
ARM: at91: sama5d4: dts: change the nand compatible string
ARM: at91/dt: sama5d4: add pioD controller
ARM: at91/dt: disable pull-up on vbus-gpio (PB16) to reduce power consumption
Signed-off-by: Olof Johansson <olof@lixom.net>
A lot of changes to the device tree for the 3.20 merge window, mostly with:
- More DT license convertions, only two DTS and two DTSI are still uncertain
and have not been converted yet
- Use the C-preprocessor includes in the device trees.
- Add support for the A31s SoC and improve the A80 support
- Add IR receiver, lradc, PS/2 support
- Add cpufreq support for all SoCs but the A23 and A80.
- And a lot of new boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pWBS
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-3.20' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Merge "Allwinner device tree changes for 3.20" from Maxime Ripard:
A lot of changes to the device tree for the 3.20 merge window, mostly with:
- More DT license convertions, only two DTS and two DTSI are still uncertain
and have not been converted yet
- Use the C-preprocessor includes in the device trees.
- Add support for the A31s SoC and improve the A80 support
- Add IR receiver, lradc, PS/2 support
- Add cpufreq support for all SoCs but the A23 and A80.
- And a lot of new boards
* tag 'sunxi-dt-for-3.20' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (64 commits)
ARM: dts: sun5i: Enable axp209 support on A13-OLinuxIno
ARM: sunxi: dts: Add A10/A20 PS2 pin muxing options
ARM: sunxi: dts: Add PS2 nodes to dtsi for A10,A20
ARM: dts: sun6i: Add resistive touchscreen controller node to dtsi
ARM: dts: sun4i: Add Hyundau A7HD board
ARM: dts: sun4i: Add Marsboard A10 board
ARM: dts: sun9i: Enable mmc2 on A80 Optimus Board
ARM: dts: sun9i: Add 8 bit mmc pinmux setting for mmc2
ARM: dts: sun9i: Enable mmc0 on A80 Optimus Board
ARM: dts: sun9i: Convert a80 optimus board dts to label referencing
ARM: dts: sun9i: Add mmc controller nodes to the A80 dtsi
ARM: dts: sun9i: Add mmc config clock nodes
ARM: dts: sunxi: Add missing mdio label
ARM: dts: sun5i: Add mk802_a10s board
ARM: dts: sun4i: Add mk802ii board
ARM: dts: sun4i: Add mk802 board
ARM: dts: sun4i: Add dts file for Chuwi V7 CW0825 tablet
ARM: dts: sun7i: Add dts file for Bananapro board
ARM: sun6i: Enable ARM arch timers
ARM: dts: sun6i: Convert hummingbird a31 dts to label references
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Support for the A31s
- Adding support for cpufreq using cpufreq-dt
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JU1v
-----END PGP SIGNATURE-----
Merge tag 'sunxi-core-for-3.20' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/soc
Merge "Allwinner core changes for 3.20" from Maxime Ripard:
- Support for the A31s
- Adding support for cpufreq using cpufreq-dt
* tag 'sunxi-core-for-3.20' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sunxi: Register cpufreq-dt for sun[45678]i
ARM: sunxi: Add "allwinner,sun6i-a31s" to mach-sunxi
Signed-off-by: Olof Johansson <olof@lixom.net>
Defconfig changes for both sunxi and multi_v7 defconfig in order to add the
cpufreq-related drivers and the PMIC drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUxSbuAAoJEBx+YmzsjxAgZo8P/01rghOXiWL41d0Eq/kPxLAw
/spLtsklOVIvgYezVjYjingasPQM1wfncrpFEy/zv7EVn4ZDVnPhnB7VpCAX0/S6
/pihF0BMGW3trER/NZYhhGCFhNorrE2Q4aeHXZnJzvXRYHSpBHqTAm/i4szswNz6
huwmEisOhTw5CTxwK0WntRp+wm1zD/D+9eLYrxAaMkl3NKsVqBWWH7G7yyJQyfvh
WmE//JVRbAa5bjNczB8f2zt89LZ+Ki87Ui6z3+jrjsAfscr2M3Rk8Qq6ZSj1m6Ex
vLzIwuH5ZgwTzCU/Btr4IiWQDWR8XKufeFc46gOexUwuQ5zZZz9GU40bRlHsYHbF
LCZ2hsJn6S271GbSRAPNaq2XRCxEocbdRZL25/7XXWaUwydvejMZWzNn1z4p50Ml
rjiLDYU6t0psH2lwlXr20Z5P4fP6Yy7Yd8pXnJuwYFJQrGicN6Awan67520tfvuQ
SvnVtF7vbZJ1QmJMyWrC4YuQk9NDgnyEoeEQRDIHbFPVvyR92B3LPxC6Qi+rA6nm
XtMkCj9sx5J3OYhEBR3WgzSpQhxgXIe26r9APEO51ojD9oO2Wpq3+DRStMTyrwAx
6eVHldAzmXFEkWTL8gYxIIUr/ai+HEnm3kiU0QOpMkAwpA8iauLaD+E1+OSBSETQ
dv81VZT+ckVqHRu2GZkF
=9l0R
-----END PGP SIGNATURE-----
Merge tag 'sunxi-defconfig-for-3.20' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/defconfig
Merge "Allwinner defconfig changes for 3.20" from Maxime Ripard:
Defconfig changes for both sunxi and multi_v7 defconfig in order to add the
cpufreq-related drivers and the PMIC drivers.
* tag 'sunxi-defconfig-for-3.20' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sunxi: Add AXP20x support multi_v7_defconfig
ARM: sunxi: Add AXP20x support in defconfig
ARM: multi_v7_defconfig: Enable TOUCHSCREEN_SUN4I, CPU_THERMAL
ARM: sunxi_defconfig: Enable TOUCHSCREEN_SUN4I, CPUFREQ_DT, CPU_THERMAL
Signed-off-by: Olof Johansson <olof@lixom.net>
A few minor fixes for the 3.19 kernel:
- The 8250 uart driver now respects the aliases, which pointed out that we
were using them wrong. Fixed them.
- The simplefb pipeline that was used on the A10 caused flickering and
tearing, and rendered it pretty much useless. Added a new simplefb node
with another pipeline that removes this issue. Note that we need to keep
the old node because u-boot 2015.01 uses it.
- Added a fix for the USB phy node on sun4i/sun5i
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JLlc
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner fixes for 3.19" from Maxime Ripard:
Allwinner fixes for 3.19
A few minor fixes for the 3.19 kernel:
- The 8250 uart driver now respects the aliases, which pointed out that we
were using them wrong. Fixed them.
- The simplefb pipeline that was used on the A10 caused flickering and
tearing, and rendered it pretty much useless. Added a new simplefb node
with another pipeline that removes this issue. Note that we need to keep
the old node because u-boot 2015.01 uses it.
- Added a fix for the USB phy node on sun4i/sun5i
* tag 'sunxi-fixes-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sunxi: dt: Fix aliases
ARM: dts: sun4i: Add simplefb node with de_fe0-de_be0-lcd0-hdmi pipeline
ARM: dts: sun6i: ippo-q8h-v5: Fix serial0 alias
ARM: dts: sunxi: Fix usb-phy support for sun4i/sun5i
Signed-off-by: Olof Johansson <olof@lixom.net>
- exynos3250
: add exynos_usbphy node and hsotg nodes
- exynos3250-rinato
: enable usb
: cleanup and use macro for gpio-keys
: add fimd and Panel devices support
- exynos3250-monk
: enable usb
: cleanup and use macro for gpio-keys
- exynos5250-snow
: add power and lid gpio-keys pinctrl
- exynos5420-peach-pit and exynos5800-peach-pi
: configure regulators for suspend
: set always on for USB webCam regulators
: add lid GPIO key device
- exynos5422
: add support new board Odroid XU3
- dt-bindings
: add exynos-chipid
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Yc7r
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung DT updates for v3.20" from Kukjin Kim:
- exynos3250
: add exynos_usbphy node and hsotg nodes
- exynos3250-rinato
: enable usb
: cleanup and use macro for gpio-keys
: add fimd and Panel devices support
- exynos3250-monk
: enable usb
: cleanup and use macro for gpio-keys
- exynos5250-snow
: add power and lid gpio-keys pinctrl
- exynos5420-peach-pit and exynos5800-peach-pi
: configure regulators for suspend
: set always on for USB webCam regulators
: add lid GPIO key device
- exynos5422
: add support new board Odroid XU3
- dt-bindings
: add exynos-chipid
* tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Configure regulators for suspend on exynos Peach boards
ARM: dts: Set Peach boards USB WebCam regulators to always on
ARM: dts: Add lid GPIO key device node for Peach boards
ARM: dts: Add power and lid GPIO keys pinctrl for exynos5250-snow
Documentation: dt-bindings: add exynos-chipid binding information
ARM: dts: add Panel device support for exynos3250-rinato
ARM: dts: add fimd device support for exynos3250-rinato
ARM: dts: use macro in gpio keys for exynos3250 boards
ARM: dts: remove unnecessary gpio-key nodes for exynos3250 boards
ARM: dts: Enable USB node for exynos3250-monk
ARM: dts: Enable USB node for exynos3250-rinato
ARM: dts: Add hsotg node for exynos3250
ARM: dts: Add exynos_usbphy node for exynos3250
ARM: dts: Add dts file for Odroid XU3 board
Signed-off-by: Olof Johansson <olof@lixom.net>
- several fixes and adjustments following the last cleanup batch
- removal of some unused Kconfig options
- slight PM and pm_idle rework to ease future rework
- removal of unneeded mach/system_rev.h
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUxjj9AAoJEAf03oE53VmQGEAH/3nLneCOQeyuq60adx+Lxcdn
Q9sMMzrw4B6bQnJee7+PQD3/QU7fmF8qNKlMKYAlILFHGNQplASi4uAfRTykUA0j
RQHpS9n20ODVfX+yePJ/o8h2r1BkT2wUIDXxaZCj2RoPmEz1aiFDNa2pPsUfprRd
gpbh+ZU43LRowYwH9UHPV55PQ0ZwMq3ry2DOYY5Al1+bKQ8TFvAdDMUu3rGZU7A4
dMYiQCQ6Fv0EI1NY0IHSf/u/jujlPE2H0TSR38w8lYfIPzBx2tHkLSupuxKh7R1N
QYibgZXWR0PqHOXMpOHYBqJFj5c3f/aOZ/dO4RJha+S7YHNQnIFzLsm122njgKQ=
=KgUm
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup3' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/soc
Merge "at91: cleanup/soc for 3.20 #3 (bis) from Nicolas Ferre:
Third batch of cleanup/soc for 3.20:
- several fixes and adjustments following the last cleanup batch
- removal of some unused Kconfig options
- slight PM and pm_idle rework to ease future rework
- removal of unneeded mach/system_rev.h
* tag 'at91-cleanup3' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: pm: remove warning to remove SOC_AT91SAM9263 usage
ARM: at91: remove unused mach/system_rev.h
ARM: at91: stop using HAVE_AT91_DBGUx
ARM: at91: fix ordering of SRAM and PM initialization
ARM: at91: sam9: set arm_pm_idle from sam9_dt_device_init
ARM: at91: fix sam9n12 and sam9x5 arm_pm_idle
ARM: at91: mark const init data with __initconst instead of __initdata
ARM: at91: fix PM initialization for newer SoCs
ARM: at91: fix Kconfig.debug by adding DEBUG_AT91_UART option
Signed-off-by: Olof Johansson <olof@lixom.net>
The entries are separated as ARM V4/V5 and ARM V7 as some other per-SoC config
options may be removed in the near future.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Willy Tarreau <w@1wt.eu>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Willy Tarreau <w@1wt.eu>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Benoit Masson <yahoo@perenite.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Willy Tarreau <w@1wt.eu>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Willy Tarreau <w@1wt.eu>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ben Peddell <klightspeed@killerwolves.net>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ryan Press <ryan@presslab.us>
Acked-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ryan Press <ryan@presslab.us>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The twl4030 keypad is not wired up in the gta04, so mark it disabled
to avoid pointless initialization.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>
i.e. configure vpll2 as a supply for the dss rather
than being always-on.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add comments to state which GPIO is used for some interrupts.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>
mcbsp2 is used in gta04 soundcard config and by default
is disabled so enable it for gta04.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add minimal hwmod support that works at least on dm8168. This
is based on the code in the earlier TI CDP tree, and an earlier
patch by Aida Mynzhasova <aida.mynzhasova@skitlab.ru>.
I've set up things to work pretty much the same way as for
am33xx. We are basically using cm33xx.c with a different set
of clocks and clockdomains.
This code is based on the TI81XX-LINUX-PSP-04.04.00.02 patches
published at:
http://downloads.ti.com/dsps/dsps_public_sw/psp/LinuxPSP/TI81XX_04_04/04_04_00_02/index_FDS.html
Cc: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds required definitions and structures for clockdomain
initialization, so omap3xxx_clockdomains_init() was substituted by
new ti81xx_clockdomains_init() while early initialization of
TI81XX platform.
Note that we now need to have 81xx in a separate CONFIG_SOC_TI81XX
block instead inside the ifdef block for omap3 to avoid make
randconfig build errors.
This code is based on the TI81XX-LINUX-PSP-04.04.00.02 patches
published at:
http://downloads.ti.com/dsps/dsps_public_sw/psp/LinuxPSP/TI81XX_04_04/04_04_00_02/index_FDS.html
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Aida Mynzhasova <aida.mynzhasova@skitlab.ru>
[tony@atomide.com: updated to apply, renamed to clockdomains81xx.c,
fixed to use am33xx_clkdm_operations, various fixes suggested by
Paul Walmsley]
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows booting ti81xx boards when a .dts file
is in place.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Sylwester Nawrocki