Attempting to transmit rx_done messages after the GLINK instance is
being torn down will cause use after free and memory leaks. So cancel
the intent_work and free up the pending intents.
With this there are no concurrent accessors of the channel left during
qcom_glink_native_remove() and there is therefor no need to hold the
spinlock during this operation - which would prohibit the use of
cancel_work_sync() in the release function. So remove this.
Fixes: 1d2ea36eea ("rpmsg: glink: Add rx done command")
Cc: stable@vger.kernel.org
Acked-by: Chris Lew <clew@codeaurora.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The device release function is set before registering with rpmsg. If
rpmsg registration fails, the framework will call device_put(), which
invokes the release function. The channel create logic does not need to
free rpdev if rpmsg_register_device() fails and release is called.
Fixes: b4f8e52b89 ("rpmsg: Introduce Qualcomm RPM glink driver")
Cc: stable@vger.kernel.org
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Chris Lew <clew@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In a remote processor crash scenario, there is no guarantee the remote
processor sent close requests before it went into a bad state. Remove
the reference that is normally handled by the close command in the
so channel resources can be released.
Fixes: b4f8e52b89 ("rpmsg: Introduce Qualcomm RPM glink driver")
Cc: stable@vger.kernel.org
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Chris Lew <clew@codeaurora.org>
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Extra channel reference put when remote sending OPEN_ACK after timeout
causes use-after-free while handling next remote CLOSE command.
Remove extra reference put in timeout case to avoid use-after-free.
Fixes: b4f8e52b89 ("rpmsg: Introduce Qualcomm RPM glink driver")
Cc: stable@vger.kernel.org
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Memory allocated for re-usable intents are not freed during channel
cleanup which causes memory leak in system.
Check and free all re-usable memory to avoid memory leak.
Fixes: 933b45da5d ("rpmsg: glink: Add support for TX intents")
Cc: stable@vger.kernel.org
Acked-By: Chris Lew <clew@codeaurora.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When wrapping around the FIFO, the remote expects the tail pointer to
be reset to 0 on the edge case where the tail equals the FIFO length.
Fixes: caf989c350 ("rpmsg: glink: Introduce glink smem based transport")
Cc: stable@vger.kernel.org
Signed-off-by: Chris Lew <clew@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In rpmsg_eptdev_write_iter, if copy_from_iter_full fails the allocated
buffer needs to be released.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Naming the glink edge device on the parent of_node short name causes
collisions when multiple remoteproc instances with only different unit
address are described on the platform_bus in DeviceTree.
Base the edge's name on the parent remoteproc's name instead, to ensure
that it's unique.
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct {
...
struct intent_pair intents[];
} __packed * msg;
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
So, replace the following form:
sizeof(*msg) + sizeof(struct intent_pair) * count
with:
struct_size(msg, intents, count)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The virtio_rpmsg_bus driver uses the "%p" format-specifier for
printing the vring buffer address. This prints only a hashed
pointer even for previliged users. Use "%pK" instead so that
the address can be printed during debug using kptr_restrict
sysctl.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Minor typos, grammar and copy/paste issues. Fix for consistency. No
functional or semantic change.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Most other bus (for example, SPI, i2c) have the remove handler for
driver optional. Make remove handler for rpmsg driver optional too.
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Remoteproc is now capable to create one specific sub-device per
virtio link to associate a dedicated memory pool.
This implies to change device used by virtio_rpmsg for
buffer allocation from grand-parent to parent.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Tested-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The current rx peak function fails to read the data if size is
less than 4bytes.
Use memcpy_fromio to support data reads of size less than 4 bytes.
Cc: stable@vger.kernel.org
Fixes: f0beb4ba9b ("rpmsg: glink: Remove chunk size word align warning")
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Currently a failed allocation of channel->name leads to an
immediate return without freeing channel. Fix this by setting
ret to -ENOMEM and jumping to an exit path that kfree's channel.
Detected by CoverityScan, CID#1473692 ("Resource Leak")
Fixes: 53e2822e56 ("rpmsg: Introduce Qualcomm SMD backend")
Cc: stable@vger.kernel.org
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
It is possible for the chunk sizes coming from the non RPM remote procs
to not be word aligned. Remove the alignment warning and continue to
read from the FIFO so execution is not stalled.
Signed-off-by: Chris Lew <clew@codeaurora.org>
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-remoteproc@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In order to be able to use the aio interface for writing to a rpmsg_char
the write_iter function must be implemented, so migrate to iter version
for read and write functions.
Regular read and write uses the iter methods if present and is as such
unaffected.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add compat ioctl callback to support 32bit user space applications.
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Channels may need to identify the edge their channel was probed for.
Store the edge name by reading the label property from device tree or
default to the node name.
Signed-off-by: Chris Lew <clew@codeaurora.org>
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Some of the rpmsg devices need to switch on power domains to communicate
with remote processor. For example on Qualcomm DB820c platform LPASS
power domain needs to switched on for any kind of audio services.
This patch adds the missing power domain support in rpmsg core.
Without this patch attempting to play audio via QDSP on DB820c would
reboot the system.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch fixes below kerneldoc warnings
qcom_smd.c:141: warning: Function parameter or member 'dev' not described in 'qcom_smd_edge'
qcom_smd.c:141: warning: Function parameter or member 'name' not described in 'qcom_smd_edge'
qcom_smd.c:141: warning: Function parameter or member 'new_channel_event' not described in 'qcom_smd_edge'
qcom_smd.c:222: warning: Function parameter or member 'qsept' not described in 'qcom_smd_channel'
qcom_smd.c:222: warning: Function parameter or member 'registered' not described in 'qcom_smd_channel'
qcom_smd.c:222: warning: Function parameter or member 'state_change_event' not described in 'qcom_smd_channel'
qcom_smd.c:222: warning: Function parameter or member 'drvdata' not described in 'qcom_smd_channel'
qcom_smd.c:737: warning: Function parameter or member 'wait' not described in '__qcom_smd_send'
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fix below kerneldoc warnings while building with W=1
qcom_glink_native.c:53: warning: Function parameter or member 'data' not described in 'glink_defer_cmd'
qcom_glink_native.c:75: warning: Function parameter or member 'data' not described in 'glink_core_rx_intent'
qcom_glink_native.c:75: warning: Function parameter or member 'id' not described in 'glink_core_rx_intent'
qcom_glink_native.c:75: warning: Function parameter or member 'size' not described in 'glink_core_rx_intent'
qcom_glink_native.c:75: warning: Function parameter or member 'reuse' not described in 'glink_core_rx_intent'
qcom_glink_native.c:75: warning: Function parameter or member 'in_use' not described in 'glink_core_rx_intent'
qcom_glink_native.c:75: warning: Function parameter or member 'offset' not described in 'glink_core_rx_intent'
qcom_glink_native.c:75: warning: Function parameter or member 'node' not described in 'glink_core_rx_intent'
qcom_glink_native.c:116: warning: Function parameter or member 'features' not described in 'qcom_glink'
qcom_glink_native.c:116: warning: Function parameter or member 'intentless' not described in 'qcom_glink'
qcom_glink_native.c:524: warning: Function parameter or member 'version' not described in 'qcom_glink_receive_version'
qcom_glink_native.c:524: warning: Function parameter or member 'features' not described in 'qcom_glink_receive_version'
qcom_glink_native.c:524: warning: Excess function parameter 'r_version' description in 'qcom_glink_receive_version'
qcom_glink_native.c:524: warning: Excess function parameter 'r_features' description in 'qcom_glink_receive_version'
qcom_glink_native.c:551: warning: Function parameter or member 'version' not described in 'qcom_glink_receive_version_ack'
qcom_glink_native.c:551: warning: Function parameter or member 'features' not described in 'qcom_glink_receive_version_ack'
qcom_glink_native.c:551: warning: Excess function parameter 'r_version' description in 'qcom_glink_receive_version_ack'
qcom_glink_native.c:551: warning: Excess function parameter 'r_features' description in 'qcom_glink_receive_version_ack'
qcom_glink_native.c:570: warning: bad line: wire format and transmit
qcom_glink_native.c:604: warning: Function parameter or member 'intent' not described in 'qcom_glink_advertise_intent'
qcom_glink_native.c:604: warning: Excess function parameter 'size' description in 'qcom_glink_advertise_intent'
qcom_glink_native.c:710: warning: Function parameter or member 'glink' not described in 'qcom_glink_handle_intent_req'
qcom_glink_native.c:710: warning: Function parameter or member 'cid' not described in 'qcom_glink_handle_intent_req'
qcom_glink_native.c:710: warning: Function parameter or member 'size' not described in 'qcom_glink_handle_intent_req'
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
As intent structure members are not correctly annotated, leading to below warnings
qcom_glink_native.c:614:16: warning: incorrect type in assignment (different base types)
qcom_glink_native.c:614:16: expected unsigned short [unsigned] [usertype] id
qcom_glink_native.c:614:16: got restricted __le16 [usertype] <noident>
qcom_glink_native.c:615:18: warning: incorrect type in assignment (different base types)
qcom_glink_native.c:615:18: expected unsigned short [unsigned] [usertype] lcid
qcom_glink_native.c:615:18: got restricted __le16 [usertype] <noident>
qcom_glink_native.c:616:19: warning: incorrect type in assignment (different base types)
qcom_glink_native.c:616:19: expected unsigned int [unsigned] [usertype] count
qcom_glink_native.c:616:19: got restricted __le32 [usertype] <noident>
qcom_glink_native.c:617:18: warning: incorrect type in assignment (different base types)
qcom_glink_native.c:617:18: expected unsigned int [unsigned] [usertype] size
qcom_glink_native.c:617:18: got restricted __le32 [usertype] <noident>
qcom_glink_native.c:618:18: warning: incorrect type in assignment (different base types)
qcom_glink_native.c:618:18: expected unsigned int [unsigned] [usertype] liid
qcom_glink_native.c:618:18: got restricted __le32 [usertype] <noident>
Fix this by correctly annotating them.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add missing include of sizes.h.
drivers/rpmsg/qcom_smd.c: In function ‘qcom_smd_channel_open’:
drivers/rpmsg/qcom_smd.c:809:36: error: ‘SZ_4K’ undeclared (first use in this function)
bb_size = min(channel->fifo_size, SZ_4K);
^~~~~
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
All the managed resources would be freed by the time release function
is invoked. Handling such memory in qcom_smd_edge_release() would do
bad things.
Found this issue while testing Audio usecase where the dsp is started up
and shutdown in a loop.
This patch fixes this issue by using simple kzalloc for allocating
channel->name and channel which is then freed in qcom_smd_edge_release().
Without this patch restarting a remoteproc would crash the system.
Fixes: 53e2822e56 ("rpmsg: Introduce Qualcomm SMD backend")
Cc: <stable@vger.kernel.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Use the appropriate SPDX license identifier in the rpmsg char driver
source file and drop the previous boilerplate license text. The uapi
header file already had the SPDX license identifier added as part of
a mass update but the license text removal was deferred for later,
and this patch drops the same.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Use the appropriate SPDX license identifier in various rpmsg
glink driver source files and drop the previous boilerplate
license text.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Use the appropriate SPDX license identifier in the rpmsg SMD backend
driver source file and drop the previous boilerplate license text.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Use the appropriate SPDX license identifier in the virtio rpmsg
bus driver source file and drop the previous boilerplate license
text.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Use the appropriate SPDX license identifier in the rpmsg core
source files and drop the previous boilerplate license text.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Attempt to acquire the APCS IPC through the mailbox framework and fall
back to the old syscon based approach, to allow us to move away from
using the syscon.
Reviewed-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch adds "driver_override" device attribute for rpmsg_device which
will allow users to explicitly specify the rpmsg_driver to be used via
sysfs entry.
The "driver_override" device attribute implemented here is very similar
to "driver_override" implemented for platform, pci, and amba bus types.
One important use-case of "driver_override" device attribute is to force
use of rpmsg_chrdev driver for certain rpmsg_device instances.
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
It is possible that incoming data arrives before the client driver has
reached a point in the probe method where adequate context for handling
the incoming message has been established.
In the event that the client's callback function returns an error the
message will be left on the FIFO and by invoking the receive handler
after the device has been probed the message will be picked off the FIFO
and the callback invoked again.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
For special rpmsg devices without a primary endpoint there is nothing to
announce so don't call the backend announce create function if we didn't
create an endpoint.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The container_of macros should not use the same name for the parameter
as the member to use for lookup, as this will result in a compilation
error unless the passed parameter has the same name as the member.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In an effort to pick up channels that are in a funky state we
optimistically tried to open all channels that we found, with the
addition that we failed if the other side did not handshake the opening.
But as we're starting the modem a second time all channels are found -
in a "funky" state - and we try to open them. But the modem firmware
requires the IPCRTR to be up in order to initialize. So any channels we
try to open before that will fail and will not be opened again.
This takes care of the regression, at the cost of reintroducing the
previous behavior of handling of channels with "funky" states.
Reverts commit c12fc4519f ("rpmsg: smd: Create device for all channels")
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Switch the tx_lock to a spinlock we allow clients to use rpmsg_trysend()
from atomic context.
In order to allow clients to sleep while waiting for space in the FIFO
we release the lock temporarily around the delay; which should be
replaced by sending a READ_NOTIF and waiting for the remote to signal
us that space has been made available.
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
By switching the tx_lock to a spinlock we allow clients to use
rpmsg_trysend() from atomic context.
The mutex was interruptable as it was previously held for the duration
of some client waiting for available space in the FIFO, but this was
recently changed to only be held temporarily - allowing us to replace it
with a spinlock.
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
if device_register() returned an error! Always use put_device()
to give up the reference initialized. unregister device for
other return error.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
if device_register() returned an error! Always use put_device()
to give up the reference initialized. And unregister device for
other return error.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a few issues found in the SMD and GLINK drivers and corrects the
handling of SMD channels that are found in an (previously) unexpected state.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJaeJV5AAoJEAsfOT8Nma3FN8YP/1UjlQmor7yTeWUg37nordmy
ELjpNdjhBI6570XbeUdtBLi5LZLdYxkAxqt2J67YdnBkyL+EedlYS3tto7Rupo0e
P/kLokPJ6I+6FxwKftBi27mt8uyNdIx2nXXof2QhnjtVvXChoOj4e3BEi9KTfuMk
1LPOjldIXHN8ORibcYT5beEcyhZKdOJIsgC5qVsxJ27sLtFPVT9YHpSVVUPZIqO8
EAmSMUqzwCOaiOoEztl29izobYfBH2zR1wvLkq6TWyJXT9uhzkMuyBALbEzwzdBz
pgOm1YadEL8rHoSc2TI1sOGAfsQLxHN2h2/QwSeMeRGI1bF7w1EEmjlTKJkDdUug
+1om6t8XL08oodrCnkltSF2GGhVHaNOkdm0+sYySsWr6fPDAGO8rd4SimzMr1+9J
xIhOBeFfj4Q1xlreVgvvGPlJu1UBaJO9xK8bNShNy3irRLLRKObIAy9RkKfVD+qq
sW7xjjsDZ94rSSVGq7vs041ozBZKwa67YBn3eRuZvRHJqKyfVVIGduNx5Ld28qJJ
0Au8a4+g7fxXA0NdxYhwmHGOVEi7pb39U4aREzlJjy4fw1dGlTaEOCfjTXG2DRhs
TOuCpn2Rr9fbWjDDXUUEVQCNl8R3IoQfqUDF1VyXdPrGVeDtQvFgn9rlQFPZirt6
b184EJEuQCylkMTRqwV3
=J7N0
-----END PGP SIGNATURE-----
Merge tag 'rpmsg-v4.16' of git://github.com/andersson/remoteproc
Pull rpmsg updates from Bjorn Andersson:
"This fixes a few issues found in the SMD and GLINK drivers and
corrects the handling of SMD channels that are found in an
(previously) unexpected state"
* tag 'rpmsg-v4.16' of git://github.com/andersson/remoteproc:
rpmsg: smd: Fix double unlock in __qcom_smd_send()
rpmsg: glink: Fix missing mutex_init() in qcom_glink_alloc_channel()
rpmsg: smd: Don't hold the tx lock during wait
rpmsg: smd: Fail send on a closed channel
rpmsg: smd: Wake up all waiters
rpmsg: smd: Create device for all channels
rpmsg: smd: Perform handshake during open
rpmsg: glink: smem: Ensure ordering during tx
drivers: rpmsg: remove duplicate includes
remoteproc: qcom: Use PTR_ERR_OR_ZERO() in glink prob
We're not holding the lock here, so we shouldn't unlock.
Fixes: 178f3f75bb ("rpmsg: smd: Don't hold the tx lock during wait")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[bjorn: renamed "out" label to further distinguish the two exit paths]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
qcom_glink_alloc_channel() allocates the mutex but not initialize it.
Use mutex_init() on it to initialize it correctly.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Holding the tx lock while waiting for tx-drain events from the remote
side blocks try_send requests from failing quickly, so temporarily drop
the tx lock while waiting.
While this allows try_send to fail quickly it also could allow a
subsequent send to succeed putting a smaller packet in the FIFO while
we're waiting for room for our large packet. But as this lock is per
channel we expect that clients with ordering concerns implements their
own ordering mechanism.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Move the check for a closed channel out from the tx-full loop to fail
any send request on a non-open channel.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
It's possible to have multiple contexts waiting for new channel events
and with an upcoming change it's possible to have multiple contexts
waiting for a full FIFO. As such we need to wake them all up.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Rather than selectively creating devices only for the channels that the
remote have moved to "opening" state let's create devices for all
channels found. The driver model will match drivers to the ones we care
about and attempt to open these.
The one case where this fails is if the user loads a firmware that lacks
a particular channel of the previous firmware that was running, in which
case we would find the old channel and attempt to probe it. The channel
opening handshake will ensure this will result in a graceful failure.
The result of this patch is that we will actively open the RPM channel
even though it's left in a state other than "opening" after the boot
loader's closing of the channel.
Tested-by: Will Newton <will.newton@gmail.com>
Reported-by: Jeremy McNicoll <jmcnicol@redhat.com>
Reported-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Validate the the remote side is opening the channel that we've found by
performing a handshake when opening the channel.
Tested-by: Will Newton <will.newton@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Ensure the ordering of the fifo write and the update of the write index,
so that the index is not updated before the data has landed in the fifo.
Acked-By: Chris Lew <clew@codeaurora.org>
Reported-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This turn RPMSG_VIRTIO into a user selectable config, fixes a few bugs in GLINK
and provides the support for specifying initial buffer sizes for GLINK
channels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jirb
-----END PGP SIGNATURE-----
Merge tag 'rpmsg-v4.15' of git://github.com/andersson/remoteproc
Pull rpmsg updates from Bjorn Andersson:
- turn RPMSG_VIRTIO into a user selectable config
- fix few bugs in GLINK
- provide the support for specifying initial buffer sizes for GLINK
channels.
* tag 'rpmsg-v4.15' of git://github.com/andersson/remoteproc:
rpmsg: glink: The mbox client knows_txdone
rpmsg: glink: Add missing MODULE_LICENSE
rpmsg: glink: Use best fit intent during tx
rpmsg: glink: Add support to preallocate intents
dt-bindings: soc: qcom: Support GLINK intents
rpmsg: glink: Initialize the "intent_req_comp" completion variable
rpmsg: Allow RPMSG_VIRTIO to be enabled via menuconfig or defconfig
As the GLINK driver is ticking the txdone of the mailbox channel (to
implement the doorbell) it needs to set knows_txdone.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The qcom_glink_native driver is missing a MODULE_LICENSE(), correct
this.
Fixes: 835764ddd9 ("rpmsg: glink: Move the common glink protocol implementation to glink_native.c")
Cc: stable@vger.kernel.org
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Intents can vary in size, try to find the best fitting remote intent
instead of first fit when sending a message to the remote proc.
Signed-off-by: Chris Lew <clew@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The base intents prequeued during channel creation may not satisfy a
channel's throughput requirement. Add support for intents dt-binding to
allow channels to specify the size and amount of intents to prequeue
during endpoint announcement.
Signed-off-by: Chris Lew <clew@codeaurora.org>
[bjorn: Altered how defaults are expressed]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The "intent_req_comp" variable is used without initialization which
results in NULL pointer dereference in qcom_glink_request_intent().
we need to initialize the completion variable before using it.
Fixes: 27b9c5b66b ("rpmsg: glink: Request for intents when unavailable")
Signed-off-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Currently, RPMSG_VIRTIO can only be enabled if some other kconfig
option selects it. This does not allow it to be enabled for
virtualized systems where Virtio RPMSG is available over Virtio
MMIO or PCI transport.
This patch updates RPMSG_VIRTIO kconfig option so that we can
enable the VirtIO RPMSG driver via menuconfig or defconfig. The
patch also removes "select RPMSG_VIRTIO" from various remoteproc
kconfig options because it is now user selectable.
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We need to free "intent" and "intent->data" on a couple error paths.
Fixes: 933b45da5d ("rpmsg: glink: Add support for TX intents")
Acked-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
If qcom_glink_tx() fails, then we need to unlock before returning the
error code.
Fixes: 27b9c5b66b ("rpmsg: glink: Request for intents when unavailable")
Acked-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The new switch cases for RPM_CMD_RX_DONE, RPM_CMD_RX_DONE_W_REUSE,
RPM_CMD_RX_INTENT_REQ_ACK, RPM_CMD_INTENT and RPM_CMD_RX_INTENT_REQ from
4 recent commits are not setting ret and so a later non-zero check on ret
is testing on a garbage value in ret. Fix this by initializing ret to zero.
Detected by CoverityScan CID#1455249 ("Uninitialized scalar variable")
Fixes: 933b45da5d ("rpmsg: glink: Add support for TX intents)
Fixes: dacbb35e93 ("glink: Receive and store the remote intent buffers")
Fixes: 27b9c5b66b ("rpmsg: glink: Request for intents when unavailable")
Fixes: 88c6060f5a ("rpmsg: glink: Handle remote rx done command")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In the case where glink->intentless is true and the call
to qcom_glink_tx fails then we have a condition where ret is
non-zero and intent is null, causing a null pointer deference
when setting intent->in_use to false. Add an extra check to
only dereference intent if intent is non-null.
Detected by: CoverityScan CID#1455247 ("Explicit null dereferenced")
Fixes: 88c6060f5a ("rpmsg: glink: Handle remote rx done command")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The common code needs to export the probe and remove symbols in order
for the SMEM and RPM drivers to access them when compiled as a module.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The idr_lock should be released in the case that we don't find the given
channel.
Fixes: 44f6df922a ("rpmsg: glink: Fix idr_lock from mutex to spinlock")
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Once the remote side sends a rx done ack, check for the intent reuse
information from it and suitably discard or reuse the remote passed
intent buffers.
Acked-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
While sending data, we search for suitable sized intent to map and
simply fail if a intent is not found. Instead request for a intent of
required size and wait till one is alloted.
Acked-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
While sending data, use the remote intent id buffer of suitable size
that was passed by remote previously.
Acked-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Just like we allocating and sending intent ids to remote, remote side
allocates and sends us the intents as well. So save the intent ids and
use it later while sending data targeting the appropriate intents based
on the size.
Acked-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Preallocate local intent buffers and pass the intent ids to the remote.
This way there are some default intents available for the remote to
start sending data without having to wait by sending intent requests. Do
this by adding the rpmsg announce_create ops, which gets called right
after the rpmsg device gets probed.
Acked-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Send RX data receive ack to remote and also inform that local intent
buffer is used and freed. This informs the remote to request for next
set of intent buffers before doing a send operation.
Acked-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
To fully read the received rx data from FIFO both the command and data
has to be read. Currently we read command, data separately and process
them. By adding an offset parameter to RX FIFO peak accessor, command
and data can be read together, simplifying things. So introduce this.
Acked-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
So previously on request from remote side, we allocated local intent
buffers and passed the ids to the remote. Now when we receive data
buffers from remote directed to that intent id, copy the data to the
corresponding preallocated intent buffer.
Acked-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Intents are nothing but pre-allocated buffers of appropriate size that
are allocated on the local side and communicated to the remote side and
the remote stores the list of intent ids that it is informed.
Later when remote side is intenting to send data, it picks up a right
intent (based on the size) and sends the data buffer and the intent id.
Local side receives the data and copies it to the local intent buffer.
The whole idea is to avoid stalls on the transport for allocating
memory, used for copy based transports.
When the remote request to allocate buffers using CMD_RX_INTENT_REQ, we
allocate buffers of requested size, store the buffer id locally and also
communicate the intent id to the remote.
Acked-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The channel members lcids, rcids synchronised using the idr_lock is
accessed in both atomic/non-atomic contexts. The readers are not
currently synchronised. That no correct, so add the readers as well
under the lock and use a spinlock.
Acked-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
G-link supports a version number and feature flags for each transport.
A combination of the version number and feature flags enable/disable:
(*) G-Link software updates for each edge
(*) Individual features for each edge
Endpoints negotiate both the version and the supported flags when
the transport is opened and they cannot be changed after negotiation has
been completed.
Each full implementation of G-Link must support a minimum of the current
version, the previous version, and the base negotiation version called v0.
Acked-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The glink protocol supports different types of transports (shared
memory). With the core protocol remaining the same, the way the
transport's memory is probed and accessed is different. So add support
for glink's smem based transports.
Adding a new smem transport register function and the fifo accessors for
the same.
Acked-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
mbox_request_channel is done in probe, so free the channel in remove.
Acked-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The TX FIFO can be full, if the remote client has not read enough data
(or) reading it slowly. So its nessecary to return -EAGAIN to the local
client to enable retry.
Acked-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Glink protocol requires that each message is aligned on a 8 byte offset.
This is purely a restriction from glink, so in order to support clients
which do not adher to this, allow data packets of any size, but align
the head index accordingly, effectively removing the alignment
restriction.
Acked-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Move the common part of glink core protocol implementation to
glink_native.c that can be shared with the smem based glink
transport in the later patches.
Acked-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
There is quite some code common in glink_rpm_probe that can reused for
glink-smem based transport as well. So split the function and move the
code to glink_native_probe that can be used later when we add the
support for glink-smem based transport. Also reuse driver's remove as
well.
Acked-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
With the intention of reusing the glink core protocol commands and code
across both rpm and smem based transports, the only thing different is
way of accessing the shared-memory of the transport (FIFO). So put the
fifo accessor's of the transport's pipe (rx/tx) behind indirections, so
that the rest of the code can be shared.
For this, have a qcom_glink_pipe that can be used in the common code
containing the indirections and wrap it with glink_rpm_pipe that
contains the transport specific members.
Acked-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Renaming the glink_rpm_xx functions and structs to qcom_glink_xx
equivalents helps to reuse the core glink protocol while adding
support for smem based glink transport in the later patches.
Acked-by: Arun Kumar Neelakantam <aneela@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
To specify memory for remoteproc, we declare (dma_declare_coherent_memory())
an area which is ioremap'ed to the vmalloc area. However, this address is
not a kernel address so virt_addr_valid(buf) fails.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Rpmsg buffer size is currently fixed to 512 bytes.
This patch introduces a new capability in struct virtproc_info
to tune shared buffer size between host and coprocessor
according to the needs.
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Commit 8a228ecfe0 ("rpmsg: Indirection table for rpmsg_endpoint
operations") has made the rpmsg_send_offchannel_raw() a static
function and local to the virtio_rpmsg_bus module, but has not
dropped the corresponding EXPORT_SYMBOL. Fix this.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch assigns the device node to the edge device, so that the edge
device drivers could read required device tree properties.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This introduces the Qualcomm GLINK protocol driver and DeviceTree-based
modalias support, as well as a number of smaller fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rhfx
-----END PGP SIGNATURE-----
Merge tag 'rpmsg-v4.13' of git://github.com/andersson/remoteproc
Pull rpmsg updates from Bjorn Andersson:
"This introduces the Qualcomm GLINK protocol driver and
DeviceTree-based modalias support, as well as a number of smaller
fixes"
* tag 'rpmsg-v4.13' of git://github.com/andersson/remoteproc:
rpmsg: Make modalias work for DeviceTree based devices
rpmsg: Drop VIRTUALIZATION dependency from RPMSG_VIRTIO
rpmsg: Don't overwrite release op of rpdev
rpmsg: virtio_rpmsg_bus: cleanup multiple assignment to ops
rpmsg: virtio_rpmsg_bus: fix nameservice address
rpmsg: cleanup incorrect function in dev_err message
rpmsg: virtio_rpmsg_bus: fix announce for devices without endpoint
rpmsg: Introduce Qualcomm RPM glink driver
soc: qcom: Add device tree binding for GLINK RPM
rpmsg: Release rpmsg devices in backends
Pull networking updates from David Miller:
"Reasonably busy this cycle, but perhaps not as busy as in the 4.12
merge window:
1) Several optimizations for UDP processing under high load from
Paolo Abeni.
2) Support pacing internally in TCP when using the sch_fq packet
scheduler for this is not practical. From Eric Dumazet.
3) Support mutliple filter chains per qdisc, from Jiri Pirko.
4) Move to 1ms TCP timestamp clock, from Eric Dumazet.
5) Add batch dequeueing to vhost_net, from Jason Wang.
6) Flesh out more completely SCTP checksum offload support, from
Davide Caratti.
7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
Neira Ayuso, and Matthias Schiffer.
8) Add devlink support to nfp driver, from Simon Horman.
9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
Prabhu.
10) Add stack depth tracking to BPF verifier and use this information
in the various eBPF JITs. From Alexei Starovoitov.
11) Support XDP on qed device VFs, from Yuval Mintz.
12) Introduce BPF PROG ID for better introspection of installed BPF
programs. From Martin KaFai Lau.
13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.
14) For loads, allow narrower accesses in bpf verifier checking, from
Yonghong Song.
15) Support MIPS in the BPF selftests and samples infrastructure, the
MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
Daney.
16) Support kernel based TLS, from Dave Watson and others.
17) Remove completely DST garbage collection, from Wei Wang.
18) Allow installing TCP MD5 rules using prefixes, from Ivan
Delalande.
19) Add XDP support to Intel i40e driver, from Björn Töpel
20) Add support for TC flower offload in nfp driver, from Simon
Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
Kicinski, and Bert van Leeuwen.
21) IPSEC offloading support in mlx5, from Ilan Tayari.
22) Add HW PTP support to macb driver, from Rafal Ozieblo.
23) Networking refcount_t conversions, From Elena Reshetova.
24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
for tuning the TCP sockopt settings of a group of applications,
currently via CGROUPs"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
cxgb4: Support for get_ts_info ethtool method
cxgb4: Add PTP Hardware Clock (PHC) support
cxgb4: time stamping interface for PTP
nfp: default to chained metadata prepend format
nfp: remove legacy MAC address lookup
nfp: improve order of interfaces in breakout mode
net: macb: remove extraneous return when MACB_EXT_DESC is defined
bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
bpf: fix return in load_bpf_file
mpls: fix rtm policy in mpls_getroute
net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
...
When rpmsg devices are expected to be matched based on their compatible
the modalias should reflect this, so that module autoloading has a
chance to match and load the appropriate module.
Tested-by: Rob Clark <robdclark@gmail.com>
Reported-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A dependency to VIRTUALIZATION has been added to RPMSG_VIRTIO (back
when it was named RPMSG) in v3.10 kernel in commit 397944df32
("rpmsg: fix kconfig dependencies for VIRTIO") to resolve Kconfig
warnings due to the inclusion of the virtio configuration file from
the ARM's KVM config file. The KVM config was fixed properly in the
subsequent release in commit 8bd4ffd6b3 ("ARM: kvm: don't include
drivers/virtio/Kconfig"). So, drop this unneeded VIRTUALIZATION
dependency from RPMSG_VIRTIO.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
b0b03b8119 ("rpmsg: Release rpmsg devices in backends") attempted to
correct the ownership of freeing rpmsg device memory. But the patch
is not complete, in that the rpmsg core will overwrite the release op as
the device is being registered.
Fixes: b0b03b8119 ("rpmsg: Release rpmsg devices in backends")
Reported-by: Henri Roosen <henri.roosen@ginzinger.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Trivial cleanup: the .ops pointer is assigned twice. This patch removes the
first assignment.
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Henri Roosen <henri.roosen@ginzinger.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Commit 2a48d7322d ("rpmsg: rpmsg_send() operations takes rpmsg_endpoint")
only changed the nameservice address for virtio_rpmsg_announce_create() but
did not do the same change for virtio_rpmsg_announce_destroy().
Signed-off-by: Henri Roosen <henri.roosen@ginzinger.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Bjorn Andersson