commit 0f8e8ef7 (clocksource: Simplify clocksource watchdog resume
logic) introduced a potential kgdb dead lock. When the kernel is
stopped by kgdb inside code which holds watchdog_lock then kgdb dead
locks in clocksource_resume_watchdog().
clocksource_resume_watchdog() is called from kbdg via
clocksource_touch_watchdog() to avoid that the clock source watchdog
marks TSC unstable after the kernel has been stopped.
Solve this by replacing spin_lock with a spin_trylock and just return
in case the lock is held. Not resetting the watchdog might result in
TSC becoming marked unstable, but that's an acceptable penalty for
using kgdb.
The timekeeping is anyway easily screwed up by kgdb when the system
uses either jiffies or a clock source which wraps in short intervals
(e.g. pm_timer wraps about every 4.6s), so we really do not have to
worry about that occasional TSC marked unstable side effect.
The second caller of clocksource_resume_watchdog() is
clocksource_resume(). The trylock is safe here as well because the
system is UP at this point, interrupts are disabled and nothing else
can hold watchdog_lock().
Reported-by: Jason Wessel <jason.wessel@windriver.com>
LKML-Reference: <1264480000-6997-4-git-send-email-jason.wessel@windriver.com>
Cc: kgdb-bugreport@lists.sourceforge.net
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers, init: Limit the number of per cpu calibration bootup messages
posix-cpu-timers: optimize and document timer_create callback
clockevents: Add missing include to pacify sparse
x86: vmiclock: Fix printk format
x86: Fix printk format due to variable type change
sparc: fix printk for change of variable type
clocksource/events: Fix fallout of generic code changes
nohz: Allow 32-bit machines to sleep for more than 2.15 seconds
nohz: Track last do_timer() cpu
nohz: Prevent clocksource wrapping during idle
nohz: Type cast printk argument
mips: Use generic mult/shift factor calculation for clocks
clocksource: Provide a generic mult/shift factor calculation
clockevents: Use u32 for mult and shift factors
nohz: Introduce arch_needs_cpu
nohz: Reuse ktime in sub-functions of tick_check_idle.
time: Remove xtime_cache
time: Implement logarithmic time accumulation
powerpc grew a new warning due to the type change of clockevent->mult.
The architectures which use parts of the generic time keeping
infrastructure tripped over my wrong assumption that
clocksource_register is only used when GENERIC_TIME=y.
I should have looked and also I should have known better. These
renitent Gaul villages are racking my nerves. Some serious deprecating
is due.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The dynamic tick allows the kernel to sleep for periods longer than a
single tick, but it does not limit the sleep time currently. In the
worst case the kernel could sleep longer than the wrap around time of
the time keeping clock source which would result in losing track of
time.
Prevent this by limiting it to the safe maximum sleep time of the
current time keeping clock source. The value is calculated when the
clock source is registered.
[ tglx: simplified the code a bit and massaged the commit msg ]
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Cc: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1250617512-23567-2-git-send-email-jon-hunter@ti.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
MIPS has two functions to calculcate the mult/shift factors for clock
sources and clock events at run time. ARM needs such functions as
well.
Implement a function which calculates the mult/shift factors based on
the frequencies to which and from which is converted. The function
also has a parameter to specify the minimum conversion range in
seconds. This range is guaranteed not to produce a 64bit overflow when
a value is multiplied with the calculated mult factor. The larger the
conversion range the less becomes the conversion accuracy.
Provide two inline wrappers which handle clock events and clock
sources. For clock events the "from" frequency is nano seconds per
second which corresponds to 1GHz and "to" is the device frequency. For
clock sources "from" is the device frequency and "to" is nano seconds
per second.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <20091111134229.766673305@linutronix.de>
This patch was generated by
git grep -E -i -l 's(le|el)ct' | xargs -r perl -p -i -e 's/([Ss])(le|el)ct/$1elect/
with only skipping net/netfilter/xt_SECMARK.c and
include/linux/netfilter/xt_SECMARK.h which have a struct member called
selctx.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
git commit 75c5158f70 converted the clocksource spinlock to a
mutex. This causes the following BUG:
BUG: sleeping function called from invalid context at
kernel/mutex.c:280 in_atomic(): 0, irqs_disabled(): 1, pid: 2473,
name: pm-suspend 2 locks held by pm-suspend/2473:
#0: (&buffer->mutex){......}, at: [<ffffffff8115ab13>]
sysfs_write_file+0x3c/0x137
#1: (pm_mutex){......}, at: [<ffffffff810865b5>]
enter_state+0x39/0x130 Pid: 2473, comm: pm-suspend Not tainted 2.6.31
#1 Call Trace:
[<ffffffff810792f0>] ? __debug_show_held_locks+0x22/0x24
[<ffffffff8104a2ef>] __might_sleep+0x107/0x10b
[<ffffffff8141fca9>] mutex_lock_nested+0x25/0x43
[<ffffffff81073537>] clocksource_resume+0x1c/0x60
[<ffffffff81072902>] timekeeping_resume+0x1e/0x1c8
[<ffffffff812aee62>] __sysdev_resume+0x25/0xcf
[<ffffffff812aef79>] sysdev_resume+0x6d/0xae
[<ffffffff810864f8>] suspend_devices_and_enter+0x12b/0x1af
[<ffffffff8108665b>] enter_state+0xdf/0x130
[<ffffffff81085dc3>] state_store+0xb6/0xd3
[<ffffffff81204c73>] kobj_attr_store+0x17/0x19
[<ffffffff8115abd2>] sysfs_write_file+0xfb/0x137
[<ffffffff811057d2>] vfs_write+0xae/0x10b
[<ffffffff81208392>] ? __up_read+0x1a/0x7f
[<ffffffff811058ef>] sys_write+0x4a/0x6e
[<ffffffff81011b82>] system_call_fastpath+0x16/0x1b
clocksource_resume is called early in the resume process, there is
only one cpu, no processes are running and the interrupts are
disabled. It is therefore possible to resume the clocksources
without taking the clocksource mutex.
Reported-by: Xiaotian Feng <xtfeng@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Tested-by: Michal Schmidt <mschmidt@redhat.com>
Cc: Xiaotian Feng <xtfeng@gmail.com>
Cc: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <20090924172952.49697825@mschwide.boeblingen.de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The down rating of clock sources in the early boot process via the
clock source watchdog mechanism can happen way before the per cpu
event queues are initialized. This leads to a boot crash on x86 when
the TSC is marked unstable in the SMP bring up.
The selection of a clock source for time keeping happens in the late
boot process so we can safely delay the list manipulation until
clocksource_done_booting() is called.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
The callers of clocksource_select must hold clocksource_mutex to
protect the clocksource_list.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
The watchdog timer is started after the watchdog clocksource
and at least one watched clocksource have been registered. The
clocksource work element watchdog_work is initialized just
before the clocksource timer is started. This is too late for
the clocksource_mark_unstable call from native_cpu_up. To fix
this use a static initializer for watchdog_work.
This resolves a boot crash reported by multiple people.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <20090911153305.3fe9a361@skybase>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Martin Schwidefsky analyzed it:
To register a clocksource the clocksource_mutex is acquired and if
necessary timekeeping_notify is called to install the clocksource as
the timekeeper clock. timekeeping_notify uses stop_machine which needs
to take cpu_add_remove_lock mutex.
Starting a new cpu is done with the cpu_add_remove_lock mutex held.
native_cpu_up checks the tsc of the new cpu and if the tsc is no good
clocksource_change_rating is called. Which needs the clocksource_mutex
and the deadlock is complete.
The solution is to replace the TSC via the clocksource watchdog
mechanism. Mark the TSC as unstable and schedule the watchdog work so
it gets removed in the watchdog thread context.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: John Stultz <johnstul@us.ibm.com>
stop_machine from a multithreaded workqueue is not allowed because
of a circular locking dependency between cpu_down and the workqueue
execution. Use a kernel thread to do the clocksource downgrade.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: john stultz <johnstul@us.ibm.com>
LKML-Reference: <20090818170942.3ab80c91@skybase>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Martin pointed out that commit 6ea41d2529 (clocksource: Call
clocksource_change_rating() outside of watchdog_lock) has a
theoretical reference count problem. The calls to
clocksource_change_rating() are now done outside of the clocksource
mutex and outside of the watchdog lock. A concurrent
clocksource_unregister() could remove the clock.
Split out the code which changes the rating from
clocksource_change_rating() into __clocksource_change_rating().
Protect the clocksource_watchdog_work() code sequence with the
clocksource_mutex() and call __clocksource_change_rating().
LKML-Reference: <alpine.LFD.2.00.0908171038420.2782@localhost.localdomain>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
The changes to the watchdog logic introduced a lock inversion between
watchdog_lock and clocksource_mutex. Change the rating outside of
watchdog_lock to avoid it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
update_wall_time calls change_clocksource HZ times per second to check
if a new clock source is available. In close to 100% of all calls
there is no new clock. Replace the tick based check by an update done
with stop_machine.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134810.711836357@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add struct timekeeper to keep the internal values timekeeping.c needs
in regard to the currently selected clock source. This moves the
timekeeping intervals, xtime_nsec and the ntp error value from struct
clocksource to struct timekeeper. The raw_time is removed from the
clocksource as well. It gets treated like xtime as a global variable.
Eventually xtime raw_time should be moved to struct timekeeper.
[ tglx: minor cleanup ]
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134809.613209842@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move the downgrade of an unstable clocksource from the timer interrupt
context into the process context of a work queue thread. This is
needed to be able to do the clocksource switch with stop_machine.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134809.354926067@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Refactor clocksource watchdog code to make it more readable. Add
clocksource_dequeue_watchdog to remove a clocksource from the watchdog
list when it is unregistered.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134809.110881699@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To resume the clocksource watchdog just remove the CLOCK_SOURCE_WATCHDOG
bit from the watched clocksource.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134808.880925790@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The clocksource watchdog marks a clock as highres capable before it
checked the deviation from the watchdog clocksource even for a single
time. Make sure that the deviation is at least checked once before
doing the switch to highres mode.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134808.627795883@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If a non high-resolution clocksource is first set as override clock
and then registered it becomes active even if the system is in one-shot
mode. Move the override check from sysfs_override_clocksource to the
clocksource selection. That fixes the bug and simplifies the code. The
check in clocksource_register for double registration of the same
clocksource is removed without replacement.
To find the initial clocksource a new weak function in jiffies.c is
defined that returns the jiffies clocksource. The architecture code
can then override the weak function with a more suitable clocksource,
e.g. the TOD clock on s390.
[ tglx: Folded in a fix from John Stultz ]
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134808.388024160@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Writing a zero length string to sys/.../current_clocksource will cause
a NULL pointer dereference if the clock events system is in one shot
(highres or nohz) mode.
Pointed-out-by: Dan Carpenter <error27@gmail.com>
LKML-Reference: <alpine.DEB.2.00.0907191545580.12306@bicker>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
commit 3f68535ada (clocksource: sanity check sysfs clocksource
changes) prevents selection of non high resolution capable
clocksources when high resolution mode is active, but did not take
into account that the same rules apply for highres=off nohz=on.
Check the tick device mode instead of hrtimer_hres_active() to verify
whether the system needs to be protected from a switch to jiffies or
other non highres capable clock sources.
Reported-by: Luming Yu <luming.yu@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas, Andrew and Ingo pointed out that we don't have any safety checks
in the clocksource sysfs entries to make sure sysadmins don't try to
change the clocksource to a non high-res timer capable clocksource (such
as jiffies) when high-res timers (HRT) is enabled. Doing so will likely
hang a system.
Correct this by filtering non HRT clocksources from available_clocksources
and not accepting non HRT clocksources with HRT enabled.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Setup clocksource mult_orig in clocksource_enable().
Clocksource drivers can save power by using keeping the
device clock disabled while the clocksource is unused.
In practice this means that the enable() and disable()
callbacks perform clk_enable() and clk_disable().
The enable() callback may also use clk_get_rate() to get
the clock rate from the clock framework. This information
can then be used to calculate the shift and mult variables.
Currently the mult_orig variable is setup from mult at
registration time only. This is conflicting with the above
case since the clock is disabled and the mult variable is
not yet calculated at the time of registration.
Moving the mult_orig setup code to clocksource_enable()
allows us to both handle the common case with no enable()
callback and the mult-changed-after-enable() case.
[ Impact: allow dynamic clock source usage ]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
LKML-Reference: <20090501054546.8193.10688.sendpatchset@rx1.opensource.se>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
So far struct clocksource acted as the interface between time/timekeeping.c
and hardware. This patch generalizes the concept so that a similar
interface can also be used in other contexts. For that it introduces
new structures and related functions *without* touching the existing
struct clocksource.
The reasons for adding these new structures to clocksource.[ch] are
* the APIs are clearly related
* struct clocksource could be cleaned up to use the new structs
* avoids proliferation of files with similar names (timesource.h?
timecounter.h?)
As outlined in the discussion with John Stultz, this patch adds
* struct cyclecounter: stateless API to hardware which counts clock cycles
* struct timecounter: stateful utility code built on a cyclecounter which
provides a nanosecond counter
* only the function to read the nanosecond counter; deltas are used internally
and not exposed to users of timecounter
The code does no locking of the shared state. It must be called at least
as often as the cycle counter wraps around to detect these wrap arounds.
Both is the responsibility of the timecounter user.
Acked-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: cleanup
Simple replacement, now the _nr is redundant.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Ingo Molnar <mingo@redhat.com>
Impact: Use new APIs
Convert kernel/time functions to use struct cpumask *.
Note the ugly bitmap declarations in tick-broadcast.c. These should
be cpumask_var_t, but there was no obvious initialization function to
put the alloc_cpumask_var() calls in. This was safe.
(Eventually 'struct cpumask' will be undefined for CONFIG_CPUMASK_OFFSTACK,
so we use a bitmap here to show we really mean it).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
The clocksource frequency is represented by
clocksource->mult/2^(clocksource->shift). Currently, when NTP makes
adjustments to the clock frequency, they are made directly to the mult
value.
This has the drawback that once changed, we cannot know what the orignal
mult value was, or how much adjustment has been applied.
This property causes problems in calculating proper ntp intervals when
switching back and forth between clocksources.
This patch separates the current mult value into a mult and mult_orig
pair. The mult_orig value stays constant, while the ntp clocksource
adjustments are done only to the mult value.
This allows for correct ntp interval calculation and additionally lays the
groundwork for a new notion of time, what I'm calling the monotonic-raw
time, which is introduced in a following patch.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'cpus4096-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
NR_CPUS: Replace NR_CPUS in speedstep-centrino.c
cpumask: Provide a generic set of CPUMASK_ALLOC macros, FIXUP
NR_CPUS: Replace NR_CPUS in cpufreq userspace routines
NR_CPUS: Replace per_cpu(..., smp_processor_id()) with __get_cpu_var
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genapic_flat_64.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/genx2apic_uv_x.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/proc.c
NR_CPUS: Replace NR_CPUS in arch/x86/kernel/cpu/mcheck/mce_64.c
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c, fix
cpumask: Use optimized CPUMASK_ALLOC macros in the centrino_target
cpumask: Provide a generic set of CPUMASK_ALLOC macros
cpumask: Optimize cpumask_of_cpu in lib/smp_processor_id.c
cpumask: Optimize cpumask_of_cpu in kernel/time/tick-common.c
cpumask: Optimize cpumask_of_cpu in drivers/misc/sgi-xp/xpc_main.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/ldt.c
cpumask: Optimize cpumask_of_cpu in arch/x86/kernel/io_apic_64.c
cpumask: Replace cpumask_of_cpu with cpumask_of_cpu_ptr
Revert "cpumask: introduce new APIs"
cpumask: make for_each_cpu_mask a bit smaller
net: Pass reference to cpumask variable in net/sunrpc/svc.c
...
Fix up trivial conflicts in drivers/cpufreq/cpufreq.c manually
This allow to dynamically generate attributes and share show/store
functions between attributes. Right now most attributes are generated
by special macros and lots of duplicated code. With the attribute
passed it's instead possible to attach some data to the attribute
and then use that in shared low level functions to do different things.
I need this for the dynamically generated bank attributes in the x86
machine check code, but it'll allow some further cleanups.
I converted all users in tree to the new show/store prototype. It's a single
huge patch to avoid unbisectable sections.
Runtime tested: x86-32, x86-64
Compiled only: ia64, powerpc
Not compile tested/only grep converted: sh, arm, avr32
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change references from for_each_cpu_mask to for_each_cpu_mask_nr
where appropriate
Reviewed-by: Paul Jackson <pj@sgi.com>
Reviewed-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There is no harm, when users can read the info and we ask often enough
during debugging for this kind of information.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
File permissions for
/sys/devices/system/clocksource/clocksource0/available_clocksource
are 600 which allows write access. But this is in fact a read only
file. So change permissions to 400.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/tglx/linux-2.6-hrt:
clocksource: make clocksource watchdog cycle through online CPUs
Documentation: move timer related documentation to a single place
clockevents: optimise tick_nohz_stop_sched_tick() a bit
locking: remove unused double_spin_lock()
hrtimers: simplify lockdep handling
timers: simplify lockdep handling
posix-timers: fix shadowed variables
timer_list: add annotations to workqueue.c
hrtimer: use nanosleep specific restart_block fields
hrtimer: add nanosleep specific restart_block member
In order to not trip the clocksource watchdog, kgdb must touch the
clocksource watchdog on the return to normal system run state.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This way it checks if the clocks are synchronized between CPUs too.
This might be able to detect slowly drifting TSCs which only
go wrong over longer time.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Revert
commit 1077f5a917
Author: Parag Warudkar <parag.warudkar@gmail.com>
Date: Wed Jan 30 13:30:01 2008 +0100
clocksource.c: use init_timer_deferrable for clocksource_watchdog
clocksource_watchdog can use a deferrable timer - reduces wakeups from
idle per second.
The watchdog timer needs to run with the specified interval. Otherwise
it will miss the possible wrap of the watchdog clocksource.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
Revert commit 1ada5cba6a ("clocksource:
make clocksource watchdog cycle through online CPUs") due to the
regression reported by Gabriel C at
http://lkml.org/lkml/2008/2/24/281
(short vesion: it makes TSC be marked as always unstable on his
machine).
Cc: Andi Kleen <ak@suse.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Robert Hancock <hancockr@shaw.ca>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Gabriel C <nix.or.die@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Flag CLOCK_SOURCE_WATCHDOG is cleared twice. Note clocksource_change_rating()
won't do anyting with the cs flag.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I found that there is a buffer overflow problem in the following code.
Version: 2.6.24-rc2,
File: kernel/time/clocksource.c:417-432
--------------------------------------------------------------------
static ssize_t
sysfs_show_available_clocksources(struct sys_device *dev, char *buf)
{
struct clocksource *src;
char *curr = buf;
spin_lock_irq(&clocksource_lock);
list_for_each_entry(src, &clocksource_list, list) {
curr += sprintf(curr, "%s ", src->name);
}
spin_unlock_irq(&clocksource_lock);
curr += sprintf(curr, "\n");
return curr - buf;
}
-----------------------------------------------------------------------
sysfs_show_current_clocksources() also has the same problem though in practice
the size of current clocksource's name won't exceed PAGE_SIZE.
I fix the bug by using snprintf according to the specification of the kernel
(Version:2.6.24-rc2,File:Documentation/filesystems/sysfs.txt)
Fix sysfs_show_available_clocksources() and sysfs_show_current_clocksources()
buffer overflow problem with snprintf().
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On x86 the PIT might become an unusable clocksource. Add an unregister
function to provide a possibilty to remove the PIT from the list of
available clock sources.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This way it checks if the clocks are synchronized between CPUs too.
This might be able to detect slowly drifting TSCs which only
go wrong over longer time.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
clocksource_watchdog can use a deferrable timer - reduces wakeups from
idle per second.
Signed-off-by: Parag Warudkar <parag.warudkar@gmail.com>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
kernel/time/clocksource.c: Convert list_for_each to
list_for_each_entry in clocksource_resume(),
sysfs_override_clocksource() and show_available_clocksources()
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
lockdep complains about the lock nesting of clocksource and watchdog lock
in the resume path.
Change the resume marker to a bit operation and remove the lock from this
path.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Gleixner