Currently "tidspbridge" driver uses its own mmu implementation and
will migrate to use this "omap iommu" eventually. This config is
provided to make this migration happen smoothly.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
This makes the framebuffer work on omap3.
Also fix the clk_get usage for checkpatch.pl
"ERROR: do not use assignment in if condition".
Cc: Imre Deak <imre.deak@nokia.com>
Cc: linux-fbdev-devel@lists.sourceforge.net
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP3430ES2_SAVEANDRESTORE_SHIFT macro is used
by powerdomain code in
"1 << OMAP3430ES2_SAVEANDRESTORE_SHIFT" manner, but
the definition was also (1 << 4), meaning we actually
modified bit 16. So the definition needs to be 4.
This fixes also a cold reset HW bug in OMAP3430 ES3.x
where some of the efuse bits are not isolated during
wake-up from off mode. This can cause randomish
cold resets with off mode. Enabling the USBTLL hardware
SAVEANDRESTORE causes the core power up assert to be
delayed in a way that we will not get faulty values
when boot ROM is reading the unisolated registers.
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename clk_init_one() to clk_preinit() to distinguish its function
from clk_init() and the individual struct clk init functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On our system we see the following messages:
Disabling unused clock "gpt2_ick"
Disabling unused clock "gpt3_ick"
Disabling unused clock "gpt4_ick"
Disabling unused clock "gpt5_ick"
...
The messages have KERN_INFO level and if you have serial
console, they normally go there. I do not think it is good
idea to print that much stuff there. Moreover, messages
are not properly prefixed and for mortals it is not
immeadietly clear where they come from.
Let's give them debugging level instead.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[paul@pwsan.com: trimmed debugging output in patch description]
The CORE DPLL M2 frequency change code should use pr_debug(), not
pr_info(), for its debug messages. Same with
omap2_clksel_round_rate_div(). While here, convert a few printk(KERN_ERR ..
into pr_err().
Signed-off-by: Paul Walmsley <paul@pwsan.com>
According to the 34xx TRM Rev. K section 11.2.4.4.11.1 "Purpose of the
DLL/CDL Module," the SDRC delay-locked-loop can be locked at any SDRC
clock frequency from 83MHz to 166MHz. CDP code unconditionally
unlocked the DLL whenever shifting to a lower SDRC speed, but this
seems unnecessary and error-prone, as the DLL is no longer able to
compensate for process, voltage, and temperature variations. Instead,
only unlock the DLL when the SDRC clock rate would be less than 83MHz.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Renumber registers in omap3_sram_configure_core_dpll() assembly code to
make space for additional parameters.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Initialize SDRC_POWER to a known-good setting when the kernel boots.
Necessary since some bootloaders don't initialize SDRC_POWER properly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Clear the SDRC_POWER.PWRENA bit before putting the SDRAM into self-refresh
mode. This prevents the SDRC from attempting to power off the SDRAM,
which can cause the system to hang.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add more barriers in the SRAM CORE DPLL M2 divider change code.
- Add a DSB SY after the function's entry point to flush all cached
and buffered writes and wait for the interconnect to claim that they
have completed[1]. The idea here is to force all delayed write
traffic going to the SDRAM to at least post to the L3 interconnect
before continuing. If these writes are allowed to occur after the
SDRC is idled, the writes will not be acknowledged and the ARM will
stall.
Note that in this case, it does not matter if the writes actually
complete to the SDRAM - it is only necessary for the writes to leave
the ARM itself. If the writes are posted by the interconnect when
the SDRC goes into idle, the writes will be delayed until the SDRC
returns from idle[2]. If the SDRC is in the middle of a write when
it is requested to enter idle, the SDRC will not acknowledge the
idle request until the writes complete to the SDRAM.[3]
The old-style DMB in sdram_in_selfrefresh is now superfluous, so,
remove it.
- Add an ISB before the function's exit point to prevent the ARM from
speculatively executing into SDRAM before the SDRAM is enabled[4].
...
1. ARMv7 ARM (DDI 0406A) A3-47, A3-48.
2. Private communication with Richard Woodruff <r-woodruff2@ti.com>.
3. Private communication with Richard Woodruff <r-woodruff2@ti.com>.
4. ARMv7 ARM (DDI 0406A) A3-48.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
With the clkdev, musb_core.c needs to register clock with name "ick".
Once all the platforms using the musb driver have been converted
to use clockdev, the clock name does not need to be passed
from the low-level init code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
SPI driver will do unhandled fault on OMAP2420 if trying to probe
non-existing SPI busses. Register those additional busses runtime only
for cpus having them.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix "tusb6010 init error 5, -19" and compilation warning from function
tusb6010_platform_retime "warning: 'sysclk_ps' is used uninitialized in this
function".
I suppose commit c094ba34b8f780885d029ce3c2715a194b780e5d was meant to test
for zero fclk_ps instead of sysclk_ps.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Roel Kluin <roel.kluin@gmail.com>
Tested-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO de-bounce clocks don't have any impact on the module idle state, so
the clock code should not wait for the module to enable after the de-bounce
clocks are enabled.
Problem found by Kevin Hilman <khilman@deeprootsystems.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The structure 'arch_mmu' accommodates the difference between omap1 and
omap2/3.
This patch provides omap2/3 specific functions
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Add a function omap2_gp_clockevent_set_gptimer() for board-*.c files
to use in .init_irq functions to configure the system tick GPTIMER.
Practical choices at this point are GPTIMER1 or GPTIMER12. Both of
these timers are in the WKUP powerdomain, and so are unaffected by
chip power management. GPTIMER1 can use sys_clk as a source, for
applications where a high-resolution timer is more important than
power management. GPTIMER12 has the special property that it has the
secure 32kHz oscillator as its source clock, which may be less prone
to glitches than the off-chip 32kHz oscillator. But on HS devices, it
may not be available for Linux use.
It appears that most boards are fine with GPTIMER1, but BeagleBoard
should use GPTIMER12 when using a 32KiHz timer source, due to hardware bugs
in revisions B4 and below. Modify board-omap3beagle.c to use GPTIMER12.
This patch originally used a Kbuild config option to select the GPTIMER,
but was changed to allow this to be specified in board-*.c files, per
Tony's request.
Kalle Vallo <kalle.valo@nokia.com> found a bug in an earlier version of
this patch - thanks Kalle.
Tested on Beagle rev B4 ES2.1, with and without CONFIG_OMAP_32K_TIMER, and
3430SDP.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Kalle Valo <kalle.valo@nokia.com>
This patch avoids waiting for the camera module to become ready,
since it doesn't have IDLEST bit.
Based on a earlier hack done by Paul Walmsley on Sep 9 2008 on
linux-omap tree.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 8ad8ff6548 breaks the OMAP2xxx
cpu_mask code, which causes OMAP2xxx to panic on boot. Fix by
removing the cpu_mask auto variable and by changing CK_242X
and CK_243X to use RATE_IN_242X/RATE_IN_243X.
Resolves
<1>Unable to handle kernel NULL pointer dereference at virtual address 0000000c
<1>pgd = c0004000
<1>[0000000c] *pgd=00000000
Internal error: Oops: 5 [#1]
Modules linked in:
CPU: 0 Not tainted (2.6.29-omap1 #32)
PC is at omap2_clk_set_parent+0x104/0x120
LR is at omap2_clk_set_parent+0x28/0x120
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
SPURIOUSIRQ is contained in bits 31:7 of INTC_SIR, so
INTC_SIR must be right shifted by 7, not 6.
No change in logic, only changes for better readability.
Refer to register definition of INTCPS_SIR_IRQ in OMAP3 Manual.
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In linus' git tree the functions can be found at:
vi arch/arm/mach-omap2/usb-tusb6010.c +200 - tusb6010_platform_retime()
vi arch/arm/mach-omap2/gpmc.c +94 - gpmc_get_fclk_period()
vi arch/arm/mach-omap2/usb-tusb6010.c +53 - tusb_set_async_mode()
vi arch/arm/mach-omap2/usb-tusb6010.c +111 - tusb_set_sync_mode()
is -ENODEV appropriate when sysclk_ps == 0?
This was found by code analysis, please review.
------------------------------>8-------------8<---------------------------------
gpmc_get_fclk_period() may return 0 when gpmc_l3_clk is not enabled. This is
not checked in tusb6010_platform_retime() nor in tusb_set_async_mode() it
seems. In tusb_set_sync_mode() this may result in a division by zero.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no anymore legacy driver for OMAP24XX Enhanced Audio Controller
in linux-omap and it was newer in mainline so cleanup these unneeded
defines and initialization code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This should be done with GPIO calls. Patches against the
mainline tree welcome to add the necessary working functionality
back.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 3f0a820c4c breaks OMAP2xxx boot
during initial propagate_rate() on osc_ck and sys_ck. Fix by
pre-initializing all struct clks before running any other clock init
code. Incorporates review comments from Russell King
<rmk+kernel@arm.linux.org.uk>.
Resolves
<1>Unable to handle kernel NULL pointer dereference at virtual address 00000000
<1>pgd = c0004000
<1>[00000000] *pgd=00000000
Internal error: Oops: 5 [#1]
Modules linked in:
CPU: 0 Not tainted (2.6.29-omap1 #37)
PC is at propagate_rate+0x10/0x60
LR is at omap2_clk_init+0x30/0x218
...
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the second go through of the old DMA_nBIT_MASK macro,and there're not
so many of them left,so I put them into one patch.I hope this is the last round.
After this the definition of the old DMA_nBIT_MASK macro could be removed.
Signed-off-by: Yang Hongyang <yanghy@cn.fujitsu.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg KH <greg@kroah.com>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Gumstix will soon be shipping a variant of their Summit board that
includes an SMSC LAN9221 ethernet interface. This patch provides
support via the smsc911x driver when enabled in kernel config.
The Overo defconfig is not updated since the LAN9221 is an option
not present on all systems.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
from 2.6.29, smc911x isn't maintained anymore. A new driver, smsc911x,
will replace it. so convert omap_ldp to use smsc911x driver.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
This fixes a compile error caused by a mismerge while rebasing the patch:
linux-2.6/arch/arm/mach-omap2/board-rx51-peripherals.c:354:
undefined reference to `twl4030_mmc_init'
Looks like I need to also update my build scripts, just grepping for error:
in the logs is not obviously enough..
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds board files and related headers for Nokia RX-51
Internet Tablet.
This patch has been updated with some clean-up patches
posted earlier to linux-omap list.
Signed-off-by: Lauri Leukkunen <lauri.leukkunen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for 3430 SDP.
Various updates have been merged into this patch from
the linux-omap list.
Patch updated to initialize regulators by David Brownell
<dbrownell@users.sourceforge.net>.
Signed-off-by: Syed Mohammed Khasim <khasim@ti.com>
David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
An upcoming Overo expansion board includes an ADS7846 touchscreen controller.
This patch adds support via the ads7846 driver when enabled in the
kernel config.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Create a generic board-file for initializing usb
on omap2430 and omap3 boards.
Patch modified by Tony to build the module based on
CONFIG_USB_MUSB_SOC. Also merged in a patch adding
the nop xceiv from Ajay Kumar Gupta <ajay.gupta@ti.com>.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Allow a cover switch to be used to cause a rescan of the
MMC slot.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Resolve longstanding issue noted by Adrian Hunter: confusion
between settting VSEL=0 (which is 1.8V on MMC1) and poweroff.
Also, leave VSEL alone if we're just powering the regulator off.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Device connected to MMC3 is assumed to be self-powered, so
set_power() function is empty. It can't be omited because
host driver requires it.
Array size for hsmmc[] is specified to allocate to allocate
an instance for the third MMC controller.
Also fix a leak which happens if invalid controller id
is passed.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When setting up HSMMC devices, pass the device nodes back so
board code can linking them to their power supply regulators.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Correct twl4030 MMC power switching: fix voltage ranges reported
for each slot, and handle them fully.
Lies corrected:
- MMC-1 doesn't support the 2.6-2.7 Volt range
- MMC-2 can't normally support anything except 1.8V
Omissions corrected
- MMC-1 *does* handle the 2.8-2.9 Volt range
- MMC-2 can handle 2.5-3.2 Volt cards, given a transceiver
Add transciever support for MMC-2; enable it for Overo and Pandora.
(Depends on something else to have set up pinmuxing for control
signals instead of as MMC2_DAT4..7 pins.)
Also shrink twl4030_hsmmc_info a smidgeon ... padding is all gone.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add 1 to buffer length for null terminator and use snprintf.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds several new GPIO pins and updates
the pin naming comments.
The patch is based on earlier patches on linux-omap
list by Manikandan Pillai <mani.pillai@ti.com>,
Vaibhav Hiremath <hvaibhav@ti.com> and
David Brownell <dbrownell@users.sourceforge.net>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no CONFIG_I2C2_OMAP_BEAGLE in mainline and it is under
removal in linux-omap also so remove this dead code now.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_TAGS should vanish soon since they're not generic arm tags.
Most of them can be converted to a platform_data or parsed
from a command line like e.g. serial tag.
For OMAP_TAG_USB we just let boards call omap_usb_init()
passing a pointer to omap_usb_config.
Patch updated by Tony for mainline, basically make
n770 and h4 compile. Also folded in a fix for OSK
by David Brownell <dbrownell@users.sourceforge.net>.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the defines to the associated board file and remove
the now unnecessary header file. Also rename
OMAP34XX_ETHR_START to LDP_ETHR_START.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the defines to the associated board file and remove
the now unnecessary header file. Also rename
OMAP24XX_ETHR_GPIO_IRQ to H4_ETHR_GPIO_IRQ.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the defines to the associated board file and remove
the now unnecessary header file. Also rename
SDP2430_ETHR_GPIO_IRQ to SDP2430_ETHR_GPIO_IRQ.
Signed-off-by: Tony Lindgren <tony@atomide.com>
* master.kernel.org:/home/rmk/linux-2.6-arm: (23 commits)
[ARM] Fix virtual to physical translation macro corner cases
[ARM] update mach-types
[ARM] 5421/1: ftrace: fix crash due to tracing of __naked functions
MX1 fix include
[ARM] 5419/1: ep93xx: fix build warnings about struct i2c_board_info
[ARM] 5418/1: restore lr before leaving mcount
ARM: OMAP: board-omap3beagle: set i2c-3 to 100kHz
ARM: OMAP: Allow I2C bus driver to be compiled as a module
ARM: OMAP: sched_clock() corrected
ARM: OMAP: Fix compile error if pm.h is included
[ARM] orion5x: pass dram mbus data to xor driver
[ARM] S3C64XX: Fix s3c64xx_setrate_clksrc
[ARM] S3C64XX: sparse warnings in arch/arm/plat-s3c64xx/irq.c
[ARM] S3C64XX: sparse warnings in arch/arm/plat-s3c64xx/s3c6400-clock.c
[ARM] S3C64XX: Fix USB host clock mux list
[ARM] S3C64XX: Fix name of USB host clock.
[ARM] S3C64XX: Rename IRQ_UHOST to IRQ_USBH
[ARM] S3C64XX: Do gpiolib configuration earlier
[ARM] S3C64XX: Staticise s3c64xx_init_irq_eint()
[ARM] SMDK6410: Declare iodesc table static
...
Changing it do 100kHz is needed to make more devices works properly. Controlling the
TI DLP Pico projector[1] doesn't work properly at 400kHz, 100kHz and lower work fine.
EDID readout is unaffected by this change.
[1] http://focus.ti.com/dlpdmd/docs/dlpdiscovery.tsp?sectionId=60&tabId=2234
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Richard Woodruff writes:
| The historic usage of this has been against single use leaf clocks
| (1st instance of gptimer). When it was used it did:
| clk_get()
| clk_set_parent()
| clk_enable()
|
| This usage was ok for that. Use on a disabled clock is needed.
|
| If there are multiple users on the clock or it is enabled there are
| problems.
|
| The call can still be unfriendly if 2 different drivers are using the
| clock with their own clock get/enable. It might be the function should
| return an error if usecount != 0 to stop surprises. It is all around
| better if the parenting is done when the clock is off.
This is a good reason to ensure that the clock is not enabled when
clk_set_parent() is called.
Acked-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The following patch enables SMC911x support to work on the OMAP LDP
board. Although the SMC911x driver will eventually be obsoleted, the
smsc911x patches are rather invasive for the -rc kernels.
Rather than risk destablising smsc911x, this simpler patch is preferred
to allow the network interface to work.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use pr_err() for errors rather than pr_debug(). pr_debug() are
compiled away unless -DDEBUG is used.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Richard Woodruff writes that chip errata prevent USBTLL SAR from working
on OMAP3 ES levels before ES3.1:
http://marc.info/?l=linux-arm-kernel&m=123319614808833&w=2
Update the OMAP3 powerdomain structures appropriately.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some OMAP3 chip behaviors change in ES levels after ES2. Modify the
existing omap_chip flags to add options for ES3.0 and ES3.1.
Add a new macro, CHIP_GE_OMAP3430ES2, to cover ES levels from ES2
onwards - a common pattern for OMAP3 features. Update all current
users of the omap_chip macros to use this new macro.
Also add CHIP_GE_OMAP3430ES3_1 to cover the USBTLL SAR errata case
(described and fixed in the following patch)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This roughly corresponds with OMAP commits: 7d06c48, 3241b19,
88b5d9b, 18a5500, 9c909ac, 5c6497b, 8b1f0bd, 2ac1da8.
For both OMAP2 and OMAP3, we note the reference and bypass clocks in
the DPLL data structure. Whenever we modify the DPLL rate, we first
ensure that both the reference and bypass clocks are enabled. Then,
we decide whether to use the reference and DPLL, or the bypass clock
if the desired rate is identical to the bypass rate, and program the
DPLL appropriately. Finally, we update the clock's parent, and then
disable the unused clocks.
This keeps the parents correctly balanced, and more importantly ensures
that the bypass clock is running whenever we reprogram the DPLL. This
is especially important because the procedure for reprogramming the DPLL
involves switching to the bypass clock.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When changing the parent of a clock, it is necessary to keep the
clock use counts balanced otherwise things the parent state will
get corrupted. Since we already disable and re-enable the clock,
we might as well use the recursive versions instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
_omap2_clksel_get_src_field() was returning the first entry which was
either the default _or_ applicable to the SoC. This is wrong - we
should be returning the first default which is applicable to the SoC.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The error checks for omap2_divisor_to_clksel() and comment disagree with
the actual value returned on error. Fix this to return the correct error
value.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
linux-omap source commit 33d000c99ee393fe2042f93e8422f94976d276ce
introduces a way to "dry run" clock changes before they're committed.
However, this involves putting logic to handle this into each and
every recalc function, and unfortunately due to the caching, led to
some bugs.
Solve both of issues by making the recalc methods always return the
clock rate for the clock, which the caller decides what to do with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clock rate change code executes inside a spinlock with hardirqs
disabled. The only code that should be messing around with the
hardirq state should be the plat-omap/clock.c code. In the
omap2_reprogram_dpllcore() case, this probably just wastes cycles, but
in the omap3_core_dpll_m2_set_rate() case, this is a nasty bug.
linux-omap source commit is b9b6208dadb5e0d8b290900a3ffa911673ca97ed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Based on a patch from Paul Walmsley <paul@pwsan.com>:
omap2_clk_enable() should enable a clock's clockdomain before
attempting to enable its parent clock's clockdomain. Similarly, in
the unlikely event that the parent clock enable fails, the clockdomain
should be disabled.
linux-omap source commit is 6d6e285e5a7912b1ea68fadac387304c914aaba8.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Based upon a patch from Paul Walmsley <paul@pwsan.com>:
If _omap2_clk_enable() fails, the clock's usecount must be decremented
by one no matter whether the clock has a parent or not.
but reorganised a bit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Several parts of the OMAP2/3 clock code use wmb() to try to ensure
that the hardware write completes before continuing. This approach is
problematic: wmb() only ensures that the write leaves the ARM. It
does not ensure that the write actually reaches the endpoint device.
The endpoint device in this case - either the PRM, CM, or SCM - is
three interconnects away from the ARM - and the final interconnect is
low-speed. And the OCP interconnects will post the write, and who
knows how long that will take to complete. So the wmb() is not what
we want. Worse, the wmb() is indiscriminate; it causes the ARM to
flush any other unrelated buffered writes and wait for the local
interconnect to acknowledge them - potentially very expensive.
Fix this by converting the wmb()s into readbacks of the same PRM/CM/SCM
register. Since the PRM/CM/SCM devices use a single OCP thread, this
will cause the MPU to block while waiting for posted writes to that device
to complete.
linux-omap source commit is 260f5487848681b4d8ea7430a709a601bbcb21d1.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Consolidate the commit code for DELAYED_APP clocks into a subroutine,
_omap2xxx_clk_commit(). Also convert the MPU barrier wmb() into an
OCP barrier, since with an MPU barrier, we have no guarantee that the
write actually reached the endpoint device.
linux-omap source commit is 0f5bdb736515801b296125d16937a21ff7b3cfdc.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
clk_disable() previously used an ARM barrier, wmb(), to try to ensure
that the hardware write completed before continuing. There are some
problems with this approach.
The first problem is that wmb() only ensures that the write leaves the
ARM -- not that it actually reaches the endpoint device. In this
case, the endpoint device - either the PRM, CM, or SCM - is three
interconnects away from the ARM, and the final interconnect is
low-speed. And the OCP interconnects will post the write, who knows
how long that will take to complete. So the wmb() is not really what
we want.
Worse, the wmb() is indiscriminate; it will cause the ARM to flush any
other unrelated buffered writes and wait for the local interconnect to
acknowledge them - potentially very expensive.
This first problem could be fixed by doing a readback of the same PRM/CM/SCM
register. Since these devices use a single OCP thread, this will cause the
MPU to wait for the write to complete.
But the primary problem is a conceptual one: clk_disable() should not
need any kind of barrier. clk_enable() needs one since device driver
code must not access a device until its clocks are known to be
enabled. But clk_disable() has no such restriction.
Since blocking the MPU on a PRM/CM/SCM write can be a very
high-latency operation - several hundred MPU cycles - it's worth
avoiding this barrier if possible.
linux-omap source commit is f4aacad2c0ed1055622d5c1e910befece24ef0e2.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Traditionally, we've tracked the parent/child relationships between
clk structures by setting the child's parent member to point at the
upstream clock. As a result, when decending the tree, we have had
to scan all clocks to find the children.
Avoid this wasteful scanning by keeping a list of the clock's children.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This implements the remainder of:
OMAP clock: move rate recalc, propagation code up to plat-omap/clock.c
from Paul Walmsley which is not covered by the previous:
[ARM] omap: move clock propagation into core omap clock code
[ARM] omap: remove unnecessary calls to propagate_rate()
[ARM] omap: move propagate_rate() calls into generic omap clock code
commits.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the standard clk_set_rate() function in omap2_clk_arch_init()
rather than omap2_select_table_rate() -- this will ensure that clock
rates are recalculated and propagated correctly after those operations
are consolidated into clk_set_rate().
linux-omap source commit is 03c03330017eeb445b01957608ff5db49a7151b6.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Current implementation will disable clocks in the order defined in clock34xx.h,
at least DPLL4_M2X2 will hang in certain cases (and prevent retention / off)
if clocks are not disabled in correct order. This patch makes sure the parent
clocks will be active when disabling a clock.
linux-omap source commit is 672680063420ef8c8c4e7271984bb9cc08171d29.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the omap3_core_dpll_m2_set_rate() function to the OMAP3 clock code,
which calls into the SRAM function omap3_sram_configure_core_dpll() to
change the CORE DPLL M2 divider. (SRAM code is necessary since rate changes
on clocks upstream from the SDRC can glitch SDRAM accesses.)
Use this function for the set_rate function pointer in the dpll3_m2_ck
struct clk. With this function in place, PM/OPP code should be able to
alter SDRAM speed via code similar to:
clk_set_rate(&dpll3_m2_ck, target_rate).
linux-omap source commit is 7f8b2b0f4fe52238c67d79dedcd2794dcef4dddd.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
For a given SDRAM clock rate, SDRAM chips require memory controllers
to use a specific set of timing minimums and maximums to transfer data
reliably. These parameters can be different for different memory chips
and can also potentially vary by board.
This patch adds the infrastructure for board-*.c files to pass this
timing data to the SDRAM controller init function. The timing data is
specified in an 'omap_sdrc_params' structure, in terms of SDRC
controller register values. An array of these structs, one per SDRC
target clock rate, is passed by the board-*.c file to
omap2_init_common_hw().
This patch does not define the values for different memory chips, nor
does it use the values for anything; those will come in subsequent patches.
linux-omap source commit is bc84ecfc795c2d1c5cda8da4127cf972f488a696.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Separate SDRC code common to OMAP2/3 from mach-omap2/sdrc2xxx.c to
mach-omap2/sdrc.c. Rename the OMAP2xxx-specific functions to use an
'omap2xxx' prefix rather than an 'omap2' prefix, and use "sdrc" in the
function names rather than "memory." Mark several functions
as static that should not be used outside the sdrc2xxx.c file.
linux-omap source commit is bf1612b9d8d29379558500cd5de9ae0367c41fc4.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename arch/arm/mach-omap2/memory.c to arch/arm/mach-omap2/sdrc2xxx.c, since
it contains exclusively SDRAM-related functions. Most of the functions
are also OMAP2xxx-specific - those which are common will be separated out
in a following patch.
linux-omap source commit is fe212f797e2efef9dc88bcb5db7cf9db3f9f562e.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the contents of the arch/arm/mach-omap2/memory.h file to the
existing mach/sdrc.h file, and remove memory.h. Modify files which
include memory.h to include asm/arch/sdrc.h instead.
linux-omap source commit is e7ae2d89921372fc4b9712a32cc401d645597807.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes a few OMAP2xxx CM_IDLEST bits that were incorrectly
marked as being OMAP2xxx-wide, when they were actually 2420-specific.
Also, originally when the PRCM register macros were defined, bit shift
macros used a "_SHIFT" suffix, and mask macros used none. This became
a source of bugs and confusion, as the mask macros were mistakenly
used for shift values. Gradually, the mask macros have been updated,
piece by piece, to add a "_MASK" suffix on the end to clarify. This
patch applies this change to the CM_IDLEST_* register bits.
The patch also adds a few bits that were missing, mostly from the 3430ES1
to ES2 revisions.
linux-omap source commits are d18eff5b5fa15e170794397a6a94486d1f774f77,
e1f1a5cc24615fb790cc763c96d1c5cfe6296f5b, and part of
9fe6b6cf8d9e0cbb429fd64553a4b3160a9e99e1
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch rolls up several cleanup patches.
1. Some unnecessarily verbose variable names are used in several clock.c
functions; clean these up per CodingStyle.
2. Remove omap2_get_clksel() and just use clk->clksel_reg and
clk->clksel_mask directly.
3. Get rid of void __iomem * usage in omap2_clksel_get_src_field.
Prepend the function name with an underscore to highlight that it is a
static function.
linux-omap source commits are 7fa95e007ea2f3c4d0ecd2779d809756e7775894,
af0ea23f1ee4a5bea3b026e38761b47089f9048a, and
91c0c979b47c44b08f80e4f8d4c990fb158d82c4.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
During _omap3_noncore_dpll_lock(), if a DPLL has no active downstream
clocks and DPLL autoidle is enabled, the DPLL may never lock, since it
will enter autoidle immediately. To resolve this, disable DPLL
autoidle while locking the DPLL, and unconditionally wait for the DPLL
to lock. This fixes some bugs where the kernel would hang when returning
from retention or return the wrong rate for the DPLL.
This patch is a collaboration with Peter de Schrijver
<peter.de-schrijver@nokia.com> and Kevin Hilman
<khilman@deeprootsystems.com>.
linux-omap source commit is 3b7de4be879f1f4f55ae59882a5cbd80f6dcf0f0.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Peter de Schrijver <peter.de-schrijver@nokia.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DPLL FREQSEL jitter correction bits are set based on a table in
the 34xx TRM, Table 4-38, according to the DPLL's internal clock
frequency "Fint." Several Fint frequency ranges are missing from this
table. Previously, we allowed these Fint frequency ranges to be
selected in the rate rounding code, but did not change the FREQSEL bits.
Correspondence with the OMAP hardware team indicates that Fint values
not in the table should not be used. So, prevent them from being
selected during DPLL rate rounding. This removes warnings and also
can prevent the chip from locking up.
The first pass through the rate rounding code will update the DPLL max
and min dividers appropriately, so later rate rounding passes will run
faster than the first.
Peter de Schrijver <peter.de-schrijver@nokia.com> put up with several
test cycles of this patch - thanks Peter.
linux-omap source commit is f9c1b82f55b60fc39eaa6e7aa1fbe380c0ffe2e9.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Peter de Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The previous DPLL rate rounding algorithm counted the divider (N) down
from the maximum to 1. Since we currently use a broad DPLL rate
tolerance, and lower N values are more power-efficient, we can often
bypass several iterations through the loop by counting N upwards from
1.
Peter de Schrijver <peter.de-schrijver@nokia.com> put up with several
test cycles of this patch - thanks Peter.
linux-omap source commit is 6f6d82bb2f80fa20a841ac3e95a6f44a5a156188.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Peter de Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove some clutter from omap2_dpll_round_rate().
linux-omap source commit is 4625dceb8583c02a6d67ededc9f6a8347b6b8cb7.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert struct dpll_data.idlest_bit field to idlest_mask. Needed since
OMAP2 uses two bits for DPLL IDLEST rather than one.
While here, add the missing idlest_* fields for DPLL3.
linux-omap source commits are 25bab0f176b0a97be18a1b38153f266c3a155784
and b0f7fd17db2aaf8e6e9a2732ae3f4de0874db01c.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
OMAP34xx ES2 TRM Delta G to H states that the divider for DPLL1_FCLK and
DPLL2_FCLK can divide by 4 in addition to dividing by 1 and 2. Encode this
into the OMAP3 clock framework.
linux-omap source commit is 050684c18f2ea0b08fdd5233a0cd3c7f96e00a0e.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix DPLL jitter correction programming. Previously,
omap3_noncore_dpll_program() stored the FREQSEL jitter correction
parameter to the wrong register. This caused jitter correction to be set
incorrectly and also caused the DPLL divider to be programmed incorrectly.
Also, fix DPLL divider programming. An off-by-one error existed in
omap3_noncore_dpll_program(), causing DPLLs to be programmed with a higher
divider than intended.
linux-omap source commit is 5c0ec88a2145cdf2f2c9cc5fae49635c4c2476c7.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Using sdti doesn't keep emu_pwrdm on if hardware supervised pwrdm
transitions are used. This causes sdti stop to work when power
management is initialized and hardware supervised pwrdm control is
enabled. This patch disables hardware supervised pwrdm control for
emu_pwrdm. Now emu_pwrdm is switched off on boot by software when it
is not used.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the clockdomain autodep code to respect omap_chip platform flags.
Resolves "Unable to handle kernel paging request at virtual address
5f75706d" panic during power management initialization on OMAP2.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enabling clock in a disabled power domain causes the power domain to be
turned on. However, the power transition is not always finished when
clk_enable() returns and this randomly crashes the kernel when an
interrupt happens right after the clk_enable, and the kernel tries to
read the irq status register for that domain.
Why the irq status register is inaccessible, I don't know. Also it
doesn't seem to be related to the module being not powered up, but to
the transition itself.
The same could perhaps happen after clk_disable also, but I have not
witnessed that.
The problem affects at least dss, cam and sgx clocks.
This change waits for the transition to be finished before returning
from omap2_clkdm_clk_enable().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SGX device on OMAP3 does not support retention, so remove RET from the
list of possible SGX power states. Problem debugged by Richard Woodruff
<r-woodruff2@ti.com>.
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Each DPLL exists in its own powerdomain (cf 34xx TRM figure 4-18) and
clockdomain; so, create powerdomain and clockdomain structures for them.
Mark each DPLL clock as belonging to their respective DPLL clockdomain.
cf. 34xx TRM Table 4-27 (among other references).
linux-omap source commits are acdb615850b9b4f7d1ab68133a16be8c8c0e7419 and
a8798a48f33e9268dcc7f30a4b4a3ce4220fe0c9.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
sys_clkout2 belongs in the core_clkdm (3430 TRM section 4.7.2.2).
It's not clear whether it actually is in the CORE clockdomain, or whether
it is technically in a different clockdomain; but this is closer to
reality than the present configuration.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add clockdomains for the CM and PRM. These will ultimately replace the
"wkup_clkdm", which appears to not actually exist on the hardware.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
struct clockdomain contains a struct powerdomain *pwrdm and const char
*pwrdm_name. The pwrdm_name is only used at initialization to look up
the appropriate pwrdm pointer. Combining these into a union saves
about 100 bytes on 3430SDP. This patch should not cause any change in
kernel function.
Updated to gracefully handle autodeps that contain invalid powerdomains,
per Russell King's review comments.
Boot-tested on BeagleBoard ES2.1.
linux-omap source commit is 718fc6cd4db902aa2242a736cc3feb8744a4c71a.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a CPUfreq frequency-table implementation for OMAP2 by
walking the PRCM rate-table for available entries and adding them to a
CPUfreq table.
CPUfreq can then be used to manage switching between all the available
entries in the PRCM rate table. Either use the CPUfreq sysfs
interface directly, (see Section 3 of Documentation/cpu-freq/user-guide.txt)
or use the cpufrequtils package:
http://www.kernel.org/pub/linux/utils/kernel/cpufreq/cpufrequtils.html
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Updated to try to use cpufreq_table if it exists.
linux-omap source commit is 77ce544fa48deb7a2003f454624e3ca10d37ab87.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Filling the set_rate and round_rate fields of dpll4_m4_ck makes
this clock programmable through clk_set_rate(). This is needed
to give omapfb control over the dss1_alwon_fck rate.
This patch includes a fix from Tomi Valkeinen <tomi.valkeinen@nokia.com>.
linux-omap source commits are e42218d45afbc3e654e289e021e6b80c657b16c2 and
9d211b761b3cdf7736602ecf7e68f8a298c13278.
Signed-off-by: Måns Rullgård <mans@mansr.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add CSI2 clock struct for handling it with clock API when TI PM is disabled.
linux-omap source commit is 8b20f4498928459276bd3366e3381ad595d23432.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The GFX/SGX functional and interface clocks have different masks, for
some unknown reason, so split EN_SGX_SHIFT into one each for fclk and
iclk.
Correct according to the TRM and the far more important 'does this
actually work at all?' metric.
linux-omap source commit is de1121fdb899f762b9e717f44eaf3fae7c00cd3e.
Signed-off-by: Daniel Stone <daniel.stone@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix some bugs in the OMAP3 clock tree pertaining to the 96MHz clocks.
The 96MHz portion of the clock tree should now have reasonable
fidelity to the 34xx TRM Rev I.
One remaining question mark: it's not clear exactly which 96MHz source
clock the USIM uses. This patch sticks with the previous setting, which
seems reasonable.
linux-omap source commit is 15c706e8179ce238c3ba70a25846a36b73bd2359.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove usbhost_sar_fclk from the OMAP3 clock framework. The bit that
the clock was tweaking doesn't actually enable or disable a clock; it
controls whether the hardware will save and restore USBHOST state
when the powerdomain changes state. (That happens to coincidentally
enable a clock for the duration of the operation, hence the earlier
confusion.)
In place of the clock, mark the USBHOST powerdomain as supporting
hardware save-and-restore functionality.
linux-omap source commit is f3ceac86a9d425d101d606d87a5af44afef27179.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a missing OMAP24xx clock, the SSI L4 interface clock,
as "ssi_l4_ick".
linux-omap source commit is ace129d39b3107d330d4cf6934385d13521f2fec.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix sparse & checkpatch warnings in OMAP2/3 PRCM & PM code. This mostly
consists of:
- converting pointer comparisons to integers in form similar to
(ptr == 0) to the standard idiom (!ptr)
- labeling a few non-static private functions as static
- adding prototypes for *_init() functions in the appropriate header
files, and getting rid of the corresponding open-coded extern
prototypes in other C files
- renaming the variable 'sclk' in mach-omap2/clock.c:omap2_get_apll_clkin
to avoid shadowing an earlier declaration
Clean up checkpatch issues. This mostly involves:
- converting some asm/ includes to linux/ includes
- cleaning up some whitespace
- getting rid of braces for conditionals with single following statements
Also take care of a few odds and ends, including:
- getting rid of unlikely() and likely() - none of this code is particularly
fast-path code, so the performance impact seems slim; and some of those
likely() and unlikely() indicators are probably not as accurate as the
ARM's branch predictor
- removing some superfluous casts
linux-omap source commit is 347df59f5d20fdf905afbc26b1328b0e28a8a01b.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add non-CORE DPLL rate set code and M,N programming for OMAP3.
Connect it to OMAP34xx DPLLs 1, 2, 4, 5 via the clock framework.
You may see some warnings on rate sets from the freqsel code. The
table that TI presented in the 3430 TRM Rev F does not cover Fint <
750000, which definitely occurs in practice. However, the lack of this
freqsel case does not appear to impair the DPLL rate change.
linux-omap source commit is 689fe67c6d1ad8f52f7f7b139a3274b79bf3e784.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than introducing a special 'mcbsp_clk' with code behind it in
mach-omap*/mcbsp.c to handle the SoC specifics, arrange for the mcbsp
driver to be like any other driver. mcbsp requests its fck and ick
clocks directly, and the SoC specific code deals with selecting the
correct clock.
There is one oddity to deal with - OMAP1 fiddles with the DSP clocks
and DSP reset, so we move this to the two callback functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert OMAP MMC driver to match clocks using the device ID and a
connection ID rather than a clock name. This allows us to eliminate
the OMAP1/OMAP2 differences for the function clock.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
propagate_rate() is recursive, so it makes sense to minimise the
amount of stack which is used for each recursion. So, rather than
recursing back into it from the ->recalc functions if RATE_PROPAGATES
is set, do that test at the higher level.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the clock propagation calls for set_parent and set_rate into
the core omap clock code, rather than having these calls scattered
throughout the OMAP1 and OMAP2 implementations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The original code in omap2_clk_wait_ready() used to check the low 8
bits to determine whether they were within the FCLKEN or ICLKEN
registers. Specifically, the test is satisfied when these offsets
are used:
CM_FCLKEN, CM_FCLKEN1, CM_CLKEN, OMAP24XX_CM_FCLKEN2, CM_ICLKEN,
CM_ICLKEN1, CM_ICLKEN2, CM_ICLKEN3, OMAP24XX_CM_ICLKEN4
OMAP3430_CM_CLKEN_PLL, OMAP3430ES2_CM_CLKEN2
If one of these offsets isn't used, omap2_clk_wait_ready() merely
returns without doing anything. So we should use the non-wait clkops
version instead and eliminate that conditional.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than employing run-time tests in omap2_clk_wait_ready() to
decide whether we need to wait for the clock to become ready, we
can set the .ops appropriately.
This change deals with the OMAP24xx and OMAP34xx conditionals only.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PARENT_CONTROLS_CLOCK just makes enable/disable no-op, and is
functionally an alias for ALWAYS_ENABLED. This can be handled
in the same way, using clkops_null.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
... and use it for clocks which are ALWAYS_ENABLED. These clocks
use a non-NULL enable_reg pointer for other purposes (such as
selecting clock rates.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Collect up all the common enable/disable clock operation functions
into a separate operations structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In omap24xx_cpu_suspend assembly routine, the r2 register which holds
the address of the SDRC_POWER reg is set to zero before the value is
written back triggering a fault due to writing to address zero.
It's hard to tell where this change was introduced since this file
has been moved and merged.
While this fix prevents a crash, suspend on my n810 is broken with
current kernels. I never come out of suspend.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
By Ingo Molnar, interrupts are not masked by default.
(refer to 76d2160147)
But if interrupts are not masked, the processor can wake up while in
Suspend-to-RAM state by an external interrupt. For example, if an
OMAP3 board is connected to Host PC by USB and entered to Suspend-to-RAM
state, it wake up automatically by M_IRQ_92. The disable_irq() function
can't disable the interrupt in H/W level, So I modified
arch/arm/mach-omap2/irq.c
Signed-off-by: Kim Kyuwon <chammoru@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When 32 kHz timer is used the min_delta_ns should be initialized so
that it reflects the timer programming cost. A write to the timer
device will be usually posted, but it takes roughly 3 cycles before
it is effective. If the timer is reprogrammed before that, the CPU
will stall until the previous write completes. This was pointed out by
Richard Woodruff.
Since the lower bound for min_delta_ns is 1000, the change is visible
only with tick rates less than 3 MHz.
Also note that the old value is incorrect for 32 kHz also due to
a rounding error, and it can cause the timer queue to hang (due to
clockevent code trying to program the timer with zero ticks).
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Reviewed-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The naming accidentally broke while changing the name for the
driver to not to conflict with the other mmc driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>
A spin_lock deadlock will occur when omap_mcbsp_request() is invoked.
omap_mcbsp_request()
\- clk_enable(mcbsp->clk) [takes and holds clockfw_lock]
\- omap2_clk_enable()
\- _omap2_clk_enable()
\- omap_mcbsp_clk_enable()
\- clk_enable(child clock) [tries for clockfw_lock again]
mcbsp_clk is a virtual clock and it comprises several child clocks. when
enable mcbsp_clk in omap_mcbsp_request(), the enable function of mcbsp_clk
will enable its child clocks, then the deadlock occurs.
The solution is to remove the virtual clock and enable these child clocks in
omap_mcbsp_request() directly.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix compile by removing remaining omap specific gpio
calls. Based on earlier patches by Jarkko Nikula.
Also remove old GPIO key code, there is already a patch
to do this with gpio_keys.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Russell King