This patch does not change any functionality.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes the following Coverity complaint:
Unintentional integer overflow (OVERFLOW_BEFORE_WIDEN)
overflow_before_widen: Potentially overflowing expression dma_eng_num *
65536U with type unsigned int (32 bits, unsigned) is evaluated using 32-bit
arithmetic, and then used in a context that expects an expression of type
uint64_t (64 bits, unsigned).
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This was detected by Coverity.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Set the r??_data_len variables before using these instead of after.
This patch fixes the following Coverity complaint:
const: At condition req_data_len != rsp_data_len, the value of req_data_len
must be equal to 0.
const: At condition req_data_len != rsp_data_len, the value of rsp_data_len
must be equal to 0.
dead_error_condition: The condition req_data_len != rsp_data_len cannot be
true.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Fixes: a9b6f722f6 ("[SCSI] qla2xxx: Implementation of bidirectional.") # v3.7.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Read the FC port state once instead of twice. This patch fixes the
following Coverity complaint:
Unchecked return value (CHECKED_RETURN)
check_return: Calling atomic_read without checking return value (as is
done elsewhere 80 out of 92 times).
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since sess == NULL before 'goto out_term2' is executed, the code under 'if
(sess)' cannot be reached. Hence remove that code. This was detected by
Coverity.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes a Coverity complaint about not checking the sscanf()
return value.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes the following Coverity complaint:
Unchecked return value (CHECKED_RETURN)
check_return: Calling wait_for_completion_timeout without checking return
value (as is done elsewhere 14 out of 17 times).
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Delete the PLOGIN ACK data structure from the vha->plogi_ack_list before
freeing that data structure to avoid that that list gets corrupted.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is helpful when debugging this driver to have the firmware status code
available if a mailbox command fails. Hence report that firmware status
code.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since qlt_remove_target() only calls qlt_release() if
vha->vha_tgt.qla_tgt != NULL, checking that pointer inside qlt_release()
is not necessary. This patch fixes the following Coverity complaint:
CID 188348 (#1 of 1): Dereference after null check (FORWARD_NULL)
var_deref_model: Passing null pointer &vha->vha_tgt.qla_tgt->tgt_list_entry
to list_del, which dereferences it.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Checking a pointer after it has been dereferenced is not useful. This was
detected by Coverity.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Simplify the implementation of this function by using the %phC format
specifier instead of using explicit for-loops.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch makes the code that parses the GID list easier to read without
changing the behavior of the code.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make sure that locking assumptions are verified at runtime if kernel
debugging is enabled.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality but fixes a Coverity complaint
about using a scalar as an array.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make it clear that the CDB is not modified after processing of a SCSI
command has started.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch makes it clear that the tag, hwq and qpair variables are only
used in the mq path.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The value returned by this function is not used. Hence change the return
type of this function into 'void' and remove the return statement.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch makes it clear to humans and also to the compiler that
ql_dump_buffer() does not modify the memory the @buf argument points at.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since qlt_make_local_sess() is defined before it is called, remove the
forward declaration of that function.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is no bsg code in the qla_mr.c source file. Hence do not include
the <linux/bsg-lib.h> header file from qla_mr.c.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since the put_unaligned_*() macros are used in this header file, include
the header file that defines these macros.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Fixes: 15b7a68c1d ("scsi: qla2xxx: Introduce the dsd32 and dsd64 data structures") # v5.2-rc1.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Insert a space where required, surround complex expressions in macros with
parentheses, use the UL suffix instead of the (unsigned long) cast, do not
use line continuations when not necessary and do not explicitly initialize
static variables to zero.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I'm not sure how this happened but the patch that was intended to fix abort
handling was incomplete. This patch fixes that patch as follows:
- If aborting the SCSI command failed, wait until the SCSI command
completes.
- Return SUCCESS instead of FAILED if an abort attempt races with SCSI
command completion.
- Since qla2xxx_eh_abort() increments the sp reference count by calling
sp_get(), decrement the sp reference count before returning.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Fixes: 219d27d714 ("scsi: qla2xxx: Fix race conditions in the code for aborting SCSI commands")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since qla2x00_abort_srb() starts with increasing the reference count of
@sp, decrease that same reference count before returning.
Cc: Himanshu Madhani <hmadhani@marvell.com>
Fixes: 219d27d714 ("scsi: qla2xxx: Fix race conditions in the code for aborting SCSI commands") # v5.2.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Himanshu Madhani <hmadhani@marvell.com>
Reviewed-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated driver version from 29.100.00.00 to 31.100.00.00 which is
equivalent to Phase 12 OOB.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In some cases, like while performing extensive expander reset or phy reset,
user may observe that drives are not visible in OS. Driver's
firmware-worker thread is blocked for more than 120 seconds resulting in a
call trace.
1. Received target add event for Device A and hence driver has registered
this device to SML by calling sas_rphy_add(). SML has half added this
device and returned the control to the driver by quitting from
sas_rphy_add() API, and started some background scanning on this device A.
2. While background scanning is going on device A, driver has received SAS
DEVICE STATUS CHANGE EVENT with RC code "Internal device reset" event and
hence driver has set tm_busy flag for this Device A from FW worker thread
context. When tm_busy flag is set then driver return scsi commands with
device busy status asking the kernel to retry the command after some time.
So background scanning for device A will be waiting for this tm_busy to be
cleared.
3. Meanwhile driver has received a target add event for Device B and hence
driver called sas_rphy_add() API to register this device with SML. But
since background scanning for Device A is still pending and SML is not
quitting from sas_rphy_add(), the driver’s firmware worker thread got
blocked.
4. Now driver has received SAS DEVICE STATUS CHANGE EVENT with RC code
"Internal device reset complete" event. But as driver’s firmware worker
thread got blocked in Step3, it can’t process this event and it was not
clearing the tm_busy flag and deadlock occurred (where SML was waiting for
tm_busy flag to be cleared and our FW worker thread is waiting for SML to
quit from sas_device_rphy_add() API).
Same deadlock will be observed even if device B is getting removed in
step3. So to limit these types of deadlocks driver will process the SAS
DEVICE STATUS CHANGE EVENT events from ISR context instead of processing
this event from worker thread context. This improvement avoids above
deadlock.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is to reduce the performance drop depth observed on SATA HDD
when ATA PT command is outstanding.
Driver returns IO commands with status "SAM_STAT_BUSY" whenever ATA PT
command is outstanding. With this, IO commands will be retried until this
outstanding ATA PT to complete and hence we will observe drop in
performance.
As the driver is completing the subsequent IOs commands with SAM_STAT_BUSY
status, these IOs has to go though the block layer. Hence it adds latency
to the IOs and large performance drop is observed.
So to reduce this performance dropp, added improvement in driver to return
the subsequent IOs with SCSI_MLQUEUE_DEVICE_BUSY status instead of
completing the IOs with SAM_STAT_BUSY status when ATA PT command is
outstanding. Sending command back with SCSI_MLQUEUE_DEVICE_BUSY does not go
through complete block layer stack (as scsi_done won't be called) SML will
immediately retry the command and this method will avoid latency of block
layer stack and the performance impact will be reduced.
On Local setup, ran 512k sequential read IO operation on HGST SATA drive
with existing driver & with this improvement drivers and here is the
result,
1. With existing driver: IOs are running at bandwidth of ~230 rMB/s and
whenever any ATA PT command is outstanding (e.g issued from systemd-udevd
daemon) then this bandwidth drops to ~150 rMB/s.
2. With this improvement driver: IOs are running at bandwidth of ~230 rMB/s
and whenever any ATA PT command is outstanding then this bandwidth drops to
just ~190 rMB/s.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During HBA initialization time, if handshake operation fails due to some
firmware fault then currently driver is terminating the HBA
initialization. It is possible that HBA may come up properly if diag reset
is issued.
So improvement is made in driver in such a way that before terminating the
HBA initialization, driver checks the IOC state and if IOC state is in
fault state then issue diag reset for once. If diag reset is successful
then continue with HBA initialization else terminate the HBA
initialization.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently with sysfs parameter "drv_support_bitmap" driver exposes whether
driver supports toolbox memory move command or not.
And application should issue the toolbox memory move command only if driver
tell that memory move tool box command is supported through this sysfs
parameter.
In future we can utilize this sysfs parameter if any new feature is added
and need to notify the same to applications.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Host uses the Memory Move Tool to copy data from any source/destination
combination of system memory and IOC memory.
Memory Move Tool box request contains two SGE fields, First SGE field must
contains the source buffer details described by an MPI Simple SGE. The
second SGE field must contains the destination buffer details described by
an MPI Simple SGE.
Source -> Destination
1. IOC -> IOC (Both the SGE's will be filled by application)
2. HOST -> HOST (Both the SGE's will be filled by the host,
application should give sgl_offset to first SGE offset)
3. IOC -> HOST (Application will fill the first SGE and set the
sgl_offset to second SGE and hence driver fills
the second SGE)
4. HOST -> IOC (Application will fill IOC buffer information in the
first SGE and set the sgl_offset to second SGE.
Then driver will fill the second SGE with Host buffer
information and just before posting the command to the
firmware, driver will swap these two SGEs so that first
SGE contains the HOST buffer information and second SGE
contains the IOC information.
Driver has to take care only of the 4th case, other three cases are by
default supported by the current driver design.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If driver sees the NVMe drive with "DEVICE_BLOCKED" AccessStatus in its
PCIe Device Page0, then driver removes the drive from its internal list and
does not allow any IOCTL commands to be sent to the drive and will return
the IOCTLs with "-ENODEV" status.
The driver will now allow NVMe Encapsulated IOCTL issued to the NVMe device
with an access status of DEVICE_BLOCKED. This change allows the user to
flash new drive firmware online and revive the drive.
Add NVMe device only the driver's internal list even though the device is
in the blocked state so that the device will be visible to Apps. This way
Apps can send NVMe Encapsulated IOCTLs to this drive and bring the drive
online. This NVMe drive with DEVICE_BLOCKED access status won't added to
the SML, it will be added only in the driver's internal list.
[mkp: clarified desc]
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SES device of managed PCIe switch will be enumerated same as NVMe drives.
The device info type for this SES device is
MPI26_PCIE_DEVINFO_SCSI (0x4),
whereas the device info type for NVMe drives is
MPI26_PCIE_DEVINFO_NVME (0x3).
Based on this device info type driver determines whether the device is NVMe
drive or a SES device of a managed PCIe switch.
This SES device doesn't have the PCIe device page 2 information like NVMe
drives, so driver won't read PCIe device page 2 information for SES device.
This SES device uses only IEEE SGL's, So driver build's IEEE SGL's whenever
it receives any SCSI commands for this SES device.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated MPI to 2.6.8 specification and header files to 2.00.54.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue:
During online Firmware upgrade operations it is possible that MaxDevHandles
filled in IOCFacts may change with new FW. With this we may observe kernel
panics when driver try to access the pd_handles or blocking_handles buffers
at offset greater than the old firmware's MaxDevHandle value.
Fix:
_base_check_ioc_facts_changes() looks for increase/decrease in IOCFacts
attributes during online firmware upgrade and increases the pd_handles,
blocking_handles, etc buffer sizes to new firmware's MaxDevHandle value if
this new firmware's MaxDevHandle value is greater than the old firmware's
MaxDevHandle value.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver gets a request frame from the free pool of DMA-able request frames
and fill in the required information and pass the address of the frame to
IOC/FW to pull the complete request frame. In certain places the driver
used the request frame allocated from the free pool without completely
clearing the previous data stored in it. The request contents were cleared
only for the size of the new request to be issued and that left out some
stale data in the unused part of the request. Though the IOC/FW is not
expected to access the request beyond the specified size, it is good
practice to clear complete request message frame.
So reinitialize the complete request message frame with 0s before using
it.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
PCIe Lane margin tool box request requires IEEE sgl's and hence driver
fills the SGL field with IEEE sgl's while issuing the PCIe Lane margin
ioctl request to the HBA firmware.
Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are several occasions where variable rc is being initialized with a
value that is never read and error is being re-assigned a little later on.
Clean up the code by removing rc entirely and just returning the return
value from the call to pm8001_issue_ssp_tmf
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In hisi_sas_lu_reset(), we call internal abort for SAS and SATA device
codepaths -> consolidate into a single call.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The format specifier "%p" can leak kernel address, and use "%pK" instead.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove some unnecessary code, including:
- Explicit zeroing of memory allocated for dmam_alloc_coherent()
- Some duplicated code
- Some redundant masking
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For functions which always return 0, which is never checked, make to return
void.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It will free irq automatically if devm_request_irq() failed, so drop
free_irq() if devm_request_irq() failed.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SMP frame response is written to the command table and not the SMP
response pointer from libsas, so don't bother DMA mapping (and unmapping)
the SMP response from libsas.
Suggested-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The call to kmap_atomic() in the SMP command completion code is
unnecessary, since kmap() is only really concerned with highmem, which is
not relevant on arm64. The controller only finds itself in arm64 systems.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bart Van Assche