commit 0766d20fd (langwell_gpio: modify EOI handling following change
of kernel irq subsystem) changes
- desc->chip->eoi(irq);
+
+ if (desc->chip->irq_eoi)
+ desc->chip->irq_eoi(irq_get_irq_data(irq));
+ else
+ dev_warn(pg->chip.dev, "missing EOI handler for irq %d\n", irq);
With the following explanation:
"Latest kernel has many changes in IRQ subsystem and its interfaces,
like adding irq_eoi" for struct irq_chip, this patch will make it
support both the new and old interface."
This is completely bogus.
#1) The changelog does not match the patch at all
#2) This driver relies on the assumption that it sits behind an eoi
capable interrupt line. If the implementation of the underlying
chip changes from eoi to irq_eoi then this driver has to follow
that change and not add a total bogosity.
#3) Just mechanically changing eoi to irq_eoi without checking the
background of that change is sloppy at best.
Remove the sillyness and retrieve the interrupt data from irq_desc
directly. No need to go through a sparse irq lookup.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Nothing outside of x86 can use that code.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix section mismatch by annotating using variable name suffix.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The device table is required to load modules based on modaliases.
After adding MODULE_DEVICE_TABLE, below entries will be added to
modules.pcimap:
pch_gpio 0x00008086 0x00008803 0xffffffff 0xffffffff 0x00000000 0x00000000 0x0
ml_ioh_gpio 0x000010db 0x0000802e 0xffffffff 0xffffffff 0x00000000 0x00000000 0x0
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function gen_74x164_remove and mc33880_remove are used only wrapped
by __devexit_p so define it using __devexit.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The device table is required to load modules based on modaliases.
After adding MODULE_DEVICE_TABLE, below entries will be added to modules.pcimap:
pch_gpio 0x00008086 0x00008803 0xffffffff 0xffffffff 0x00000000 0x00000000 0x0
ml_ioh_gpio 0x000010db 0x0000802e 0xffffffff 0xffffffff 0x00000000 0x00000000 0x0
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
mpc23s17 is very similar to the mcp23s08, except that registers are 16bit
wide, so extend the interface to work with both variants.
The s17 variant also has an additional address pin, so adjust platform
data structure to support up to 8 devices per SPI chipselect.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
pca953x_get_alt_pdata() uses uint16_t* as result type for
of_get_property(), but numeric of values are __be32.
Checking for negative values is bogus because of-property
values are unsigned by definition.
Instead check for proper property size.
v3: - assume big-endian properties
- check property size
v2: - removed bogus check for negative property values
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make Primecell driver probe functions take a const pointer to their
ID tables. Drivers should never modify their ID tables in their
probe handler.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
irq_chip->irq_mask/unmask are called with interrupts disabled and
irq_desc->lock held. So we cannot access i2c from this context. That's
what irq_bus_sync_unlock() is for.
Store the masked information in the chip data structure and update the
i2c bus from the irq_bus_sync_unlock() callback.
This does not need a while(pending) loop because the update to this is
always serialized via the bus lock, so we never have more than one pin
update pending.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Gregory Bean <gbean@codeaurora.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add a mutex to register communication and handling. Without the mutex,
GPIOs didn't switch as expected when toggled in a fast sequence of
status changes of multiple outputs.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Marc Zyngier <maz@misterjones.org>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Latest kernel has many changes in IRQ subsystem and its interfaces, like
adding "irq_eoi" for struct irq_chip, this patch is a follow up change
for that.
Also remove the unnecessary cast for a "void *".
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
mfd: ab8500-core chip version cut 2.0 support
mfd: Flag WM831x /IRQ as a wake source
mfd: Convert WM831x away from legacy I2C PM operations
regulator: Support MAX8998/LP3974 DVS-GPIO
mfd: Support LP3974 RTC
i2c: Convert SCx200 driver from using raw PCI to platform device
x86: OLPC: convert olpc-xo1 driver from pci device to platform device
mfd: MAX8998/LP3974 hibernation support
mfd/ab8500: remove spi support
mfd: Remove ARCH_U8500 dependency from AB8500
misc: Make AB8500_PWM driver depend on U8500 due to PWM breakage
mfd: Add __devexit annotation for vx855_remove
mfd: twl6030 irq_data conversion.
gpio: Fix cs5535 printk warnings
misc: Fix cs5535 printk warnings
mfd: Convert Wolfson MFD drivers to use irq_data accessor function
mfd: Convert TWL4030 to new irq_ APIs
mfd: Convert tps6586x driver to new irq_ API
mfd: Convert tc6393xb driver to new irq_ APIs
mfd: Convert t7166xb driver to new irq_ API
...
Commit a1f5f22adc ("gpio: timbgpio:
irq_data conversion") was slightly too enthusiastic in converting
timbgpio_irq() over to take an irq_data * argument instead of an
unsigned int irq argument, as it is a flow handler, which still take
IRQ numbers for now. (And on top of that, it was using the wrong
accessors.)
This fixes it up, and seems to build without warnings.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/gpio/cs5535-gpio.c: In function 'cs5535_gpio_probe':
drivers/gpio/cs5535-gpio.c:269: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'resource_size_t'
drivers/gpio/cs5535-gpio.c:269: warning: format '%x' expects type 'unsigned int', but argument 4 has type 'resource_size_t'
Use vsprintf extension %pR to format resource.
Original-patch-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds MODULE_ALIAS entries to the various cs5535 subdevice modules; this
allows the modules to automatically be loaded when cs5535-mfd loads.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cs5535-mfd driver now takes care of the PCI BAR handling; this
simplifies the gpio driver a lot.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ML7213 is a companion chip for Intel Atom E6xx series. This driver can be
used for OKI SEMICONDUCTOR ML7213 IOH(Input/Output Hub) which is for
IVI(In-Vehicle Infotainment) use. This driver can access the IOH's GPIO
device.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Marc Zyngier <maz@misterjones.org>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Cc: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Cc: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Cc: Gregory Bean <gbean@codeaurora.org>
Tested-by: Rohit Vaswani <rvaswani@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Luotao Fu <l.fu@pengutronix.de>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Cc: Alek Du <alek.du@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: Marc Zyngier <maz@misterjones.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Yin Kangkai <kangkai.yin@intel.com>
Cc: Alek Du <alek.du@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts irq_chips and flow handlers over to the new struct irq_data based
irq_chip functions.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Acked-by: "Hennerich, Michael" <Michael.Hennerich@analog.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds (well, re-adds actually) handling for events/IRQs through cs5535
GPIOs. In the wild and wooly world of CS5535, setup_event() is for
assigning an IRQ to a GPIO filter/event pair, and set_irq() sets up the
pair to trigger IRQs.
These should really only be used in highly platform-specific drivers (such
as OLPC's DCON driver). Sadly, because set_irq() uses MSRs, this causes
the driver to become X86-specific.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Daniel Drake <dsd@laptop.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The default for non-READ_BACK GPIO regs is to have the clear bits set;
this means that our original errata fix was too simplistic. This
changes it to the following behavior:
- when setting GPIOs, ignore the higher order bits (they're for
clearing, we don't need to care about them).
- when clearing GPIOs, keep all the bits, but unset (via XOR) the
lower order bit that negates the clear bit that we care about. That
is, if we're clearing GPIO 26 (val = 0x04000000), we first XOR what's
currently in the register with 0x0400 (GPIO 26's SET bit), and then
OR that with the GPIO 26's CLEAR bit.
Tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The edge detect status GPIOs function differently from the other atomic
model CS5536 GPIO registers; writing 1 to the high bits clears the GPIO,
but writing 1 to the lower bits also clears the bit.
This means that read-modify-write doesn't actually work for it, so don't
apply the errata here. If a negative edge status gets lost after
resume.. well, we tried our best!
Tested-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If GPIO request succeeds, but configuration fails, it should be released.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Eric Miao <eric.miao@canonical.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rdc321x-gpio currently fetches its driver specific data by using the
platform_device->platform_data pointer, this is wrong because the mfd
device which registers our platform_device has been added using
mfd_add_device() which sets the platform_device->driver_data pointer
instead.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
CC: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Most of the register layout, client IRQ numbers on the TC35892 is shared also
by other variants. Make this generic as tc3589x
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Rename the tc35892 core/gpio drivers to tc3589x to include
new variants in the same mfd core
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Rename the header file to include further variants within
the same mfd core driver
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Sundar Iyer <sundar.iyer@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
The AMD Geode CS5536 Companion Device Silicon Revision B1 Specification
Update mentions the follow as issue #36:
"Atomic write transactions to the atomic GPIO High Bank Feature Bit
registers should only affect the bits selected [...]"
"after Suspend, an atomic write transaction [...] will clear all
non-selected bits of the accessed register."
In other words, writing to the high bank for a single GPIO bit will
clear every other GPIO bit (but only sometimes after a suspend).
The workaround described is obvious and simple; do a read-modify-write.
This patch does that, and documents why we're doing it.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several of the GPIOs on the WM8994 are fixed function on the WM8958 so
error out if the user tries to request them with gpiolib.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This is needed for supporting the upcoming VX855 camera and OLPC DCON
drivers, as well as the advanced viafb features on non-OLPC hardware
based on this chip.
Based on earlier work by Harald Welte.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Free allocated memory. Call stmpe_disable() if it was enabled.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch removes the requirement that gpio base be supplied in
platform data.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
GPIOs on these controller are multi-functional. If you decided to use
some of them e.g. as input channels for the ADC, you surely don't want
those pins to be reassigned as simple GPIOs (which may be triggered even
from userspace via 'export'). Same for the touchscreen controller pins.
Since knowledge about the hardware is needed to decide which GPIOs to
reserve, let this bitmask be inside platform_data and provide some
defines to assist potential users.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In this case the logic is very similar but the IRQs are not exposed and
the device is not picked up via PCI
Based on a separate internal whitney point driver by Yin Kangkai.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Yin Kangkai <kangkai.yin@intel.com>
Cc: Alek Du <alek.du@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Deweird this driver.
Cc: Alek Du <alek.du@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Topcliff PCH is the platform controller hub that is going to be used in
Intel's upcoming general embedded platform. All IO peripherals in
Topcliff PCH are actually devices sitting on AMBA bus. Topcliff PCH has
GPIO I/F. Using this I/F, it is able to access system devices connected
to GPIO.
[akpm@linux-foundation.org: ese DEFINE_PCI_DEVICE_TABLE (per Joe Perches)]
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Tomoya MORINAGA <morinaga526@dsn.okisemi.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement irq_chip functionality on ADP5588/5587 GPIO expanders. Only
level sensitive interrupts are supported. Interrupts provided by this
irq_chip must be requested using request_threaded_irq().
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for generic 74x164 serial-in/parallel-out 8-bits shift
register. This driver can be used as a GPIO output expander.
[akpm@linux-foundation.org: remove unused local `refresh']
Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com>
Signed-off-by: Juhos Gabor <juhosg@openwrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some versions of the hardware can trash the IER register if simultaneous
interrupts occur. This patch works around it by using a local copy of the
register and restoring it after every interrupt.
Signed-off-by: Tomas Hallenberg <tomas.hallenberg@pelagicore.com>
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The basic GPIO controllers may be found in various on-board FPGA and ASIC
solutions that are used to control board's switches, LEDs, chip-selects,
Ethernet/USB PHY power, etc.
These controllers may not provide any means of pin setup
(in/out/open drain).
The driver supports:
- 8/16/32/64 bits registers;
- GPIO controllers with clear/set registers;
- GPIO controllers with a single "data" register;
- Big endian bits/GPIOs ordering (mostly used on PowerPC).
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>,
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Our Moorestown platform has two max7315 chips which is covered by pca953x
i2c gpio driver.
A while ago this driver got updated with nested irq thread support, and it
broke the compatibity with "request_irq". For example, the gpio_keys.c
driver can not work with this driver now. This patch fixes the issue by
switching to generic_handle_irq.
Also fix the irq_base issue: irq_base == 0 is valid, and a "-1" value
should mean invalid. IRQ 0 is not a valid IRQ, irq_base of 0 is valid.
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6:
mtd/m25p80: add support to parse the partitions by OF node
of/irq: of_irq.c needs to include linux/irq.h
of/mips: Cleanup some include directives/files.
of/mips: Add device tree support to MIPS
of/flattree: Eliminate need to provide early_init_dt_scan_chosen_arch
of/device: Rework to use common platform_device_alloc() for allocating devices
of/xsysace: Fix OF probing on little-endian systems
of: use __be32 types for big-endian device tree data
of/irq: remove references to NO_IRQ in drivers/of/platform.c
of/promtree: add package-to-path support to pdt
of/promtree: add of_pdt namespace to pdt code
of/promtree: no longer call prom_ functions directly; use an ops structure
of/promtree: make drivers/of/pdt.c no longer sparc-only
sparc: break out some PROM device-tree building code out into drivers/of
of/sparc: convert various prom_* functions to use phandle
sparc: stop exporting openprom.h header
powerpc, of_serial: Endianness issues setting up the serial ports
of: MTD: Fix OF probing on little-endian systems
of: GPIO: Fix OF probing on little-endian systems
DTB is always big-endian that's why is necessary
to convert it.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
For board-specific initialization.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: linux-kernel@vger.kernel.org
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace the arbitrary software-reset call from the device-probe
method, because:
- It is defective. To work correctly, it should be two byte writes,
not a single word write. As it stands, it does nothing.
- Some devices with sx150x expanders installed have their NRESET pins
ganged on the same line, so resetting one causes the others to reset -
not a nice thing to do arbitrarily!
- The probe, usually taking place at boot, implies a recent hard-reset,
so a software reset at this point is just a waste of energy anyway.
Therefore, make it optional, defaulting to off, as this will match the
common case of probing at powerup and also matches the current broken
no-op behavior.
Signed-off-by: Gregory Bean <gbean@codeaurora.org>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The debounce times are approximate, they can be selected using the two
input functions.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for the GPIOs on STMPE I/O Expanders.
[l.fu@pengutronix.de: fix set direction input]
[l.fu@pengutronix.de: set GPIO alternate function while requesting]
Acked-by: Luotao Fu <l.fu@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The pca953x driver requires the use of threaded irqs as its irq
demultiplexer can sleep. Our irq handler can be called from any context,
so use request_any_context_irq to allow threaded irqs as well.
Signed-off-by: Daniel Gl?ckner <dg@emlix.com>
Reported-by: Ian Jeffray <ian@jeffray.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As sysfs_notify_dirent has been made irq safe, there is no reason to not
call it directly from irq. With the work_struct removed, the remaining
element in poll_desc is a sysfs_dirent pointer which may not be NULL. We
can therefore store it directly in the idr and pass it as context to the
irq handler.
Most part of the patch deals with renaming defines and variables to
reflect their new use without functional change.
I also took the opportunity to initialize the idr statically.
Signed-off-by: Daniel Gl?ckner <dg@emlix.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Be more consistent about runtime programming interface abuse warnings,
which can reduce some confusion and trigger bugfixes. Based on an
observation and patch from Jani Nikula.
Also update doc to highlight some sleeping-call issues and to match some
recent changes.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jani Nikula <ext-jani.1.nikula@nokia.com>
Cc: "Ryan Mallon" <ryan@bluewatersys.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide sane defaults for pcf857x, so the driver can be used w/o providing
platform data (and thus can be simply bound via OF tree).
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The gpios on the max730x chips have support for internal pullups while in
input mode.
This patch adds support for configuring these pullups via platform data.
A new member ("input_pullup_active") to the platform data struct is
introduced. A set bit in this variable activates the pullups while the
respective port is in input mode. This is a compatible enhancement since
unset bits lead to disables pullups which was the default in the original
driver.
_Note_: the 4 lowest bits in "input_pullup_active" are unused because the
first 4 ports of the controller are not used, too.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (63 commits)
of/platform: Register of_platform_drivers with an "of:" prefix
of/address: Clean up function declarations
of/spi: call of_register_spi_devices() from spi core code
of: Provide default of_node_to_nid() implementation.
of/device: Make of_device_make_bus_id() usable by other code.
of/irq: Fix endian issues in parsing interrupt specifiers
of: Fix phandle endian issues
of/flattree: fix of_flat_dt_is_compatible() to match the full compatible string
of: remove of_default_bus_ids
of: make of_find_device_by_node generic
microblaze: remove references to of_device and to_of_device
sparc: remove references to of_device and to_of_device
powerpc: remove references to of_device and to_of_device
of/device: Replace of_device with platform_device in includes and core code
of/device: Protect against binding of_platform_drivers to non-OF devices
of: remove asm/of_device.h
of: remove asm/of_platform.h
of/platform: remove all of_bus_type and of_platform_bus_type references
of: Merge of_platform_bus_type with platform_bus_type
drivercore/of: Add OF style matching to platform bus
...
Fix up trivial conflicts in arch/microblaze/kernel/Makefile due to just
some obj-y removals by the devicetree branch, while the microblaze
updates added a new file.
When freeing a gpio that has not been exported, gpio_unexport() prints a
debug message when it should just fall through silently.
Example spurious message:
gpio_unexport: gpio0 status -22
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Uwe Kleine-K?nig <u.kleine-koenig@pengutronix.de>
Cc: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Found in the Versatile build:
WARNING: drivers/built-in.o(.data+0x14c): Section mismatch in reference from the variable pl061_gpio_driver to the (unknown reference) .init.data:(unknown)
The variable pl061_gpio_driver references
the (unknown reference) __initdata (unknown)
WARNING: drivers/built-in.o(.data+0x40f8): Section mismatch in reference from the variable pl011_driver to the (unknown reference) .init.data:(unknown)
The variable pl011_driver references
the (unknown reference) __initdata (unknown)
WARNING: drivers/built-in.o(.data+0x5ab4): Section mismatch in reference from the variable pl031_driver to the (unknown reference) .init.data:(unknown)
The variable pl031_driver references
the (unknown reference) __initdata (unknown)
Basically, amba_id structures must not be __initdata. Also fix:
WARNING: drivers/built-in.o(.data+0x138): Section mismatch in reference from the variable pl061_gpio_driver to the function .init.text:pl061_probe()
The variable pl061_gpio_driver references
the function __init pl061_probe()
which is an incorrectly annotated probe function. Fix it to reflect
the other AMBA bus probe functions by removing the __init attributation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
My Collabora address is no longer enabled - update the MODULE_AUTHOR
fields of drivers to my current email address.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement generic OF gpio hooks and thus make device-enabled GPIO chips
(i.e. the ones that have gpio_chip->dev specified) automatically attach
to the OpenFirmware subsystem. Which means that now we can handle I2C and
SPI GPIO chips almost* transparently.
* "Almost" because some chips still require platform data, and for these
chips OF-glue is still needed, though with this change the glue will
be much smaller.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Bill Gatliff <bgat@billgatliff.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
CC: linux-kernel@vger.kernel.org
CC: devicetree-discuss@lists.ozlabs.org
Currently the kernel uses the struct device_node.data pointer to resolve
a struct gpio_chip pointer from a device tree node. However, the .data
member doesn't provide any type checking and there aren't any rules
enforced on what it should be used for. There's no guarantee that the
data stored in it actually points to an gpio_chip pointer.
Instead of relying on the .data pointer, this patch modifies the code
to add a lookup function which scans through the registered gpio_chips
and returns the gpio_chip that has a pointer to the specified
device_node.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Anton Vorontsov <avorontsov@ru.mvista.com>
CC: Grant Likely <grant.likely@secretlab.ca>
CC: David Brownell <dbrownell@users.sourceforge.net>
CC: Bill Gatliff <bgat@billgatliff.com>
CC: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Jean Delvare <khali@linux-fr.org>
CC: linux-kernel@vger.kernel.org
CC: devicetree-discuss@lists.ozlabs.org
The OF gpio infrastructure is great for describing GPIO connections within
the device tree. However, using a GPIO binding still requires changes to
the gpio controller just to add an of_gpio structure. In most cases, the
gpio controller doesn't actually need any special support and the simple
OF gpio mapping function is more than sufficient. Additional, the current
scheme of using of_gpio_chip requires a convoluted scheme to maintain
1:1 mappings between of_gpio_chip and gpio_chip instances.
If the struct of_gpio_chip data members were moved into struct gpio_chip,
then it would simplify the processing of OF gpio bindings, and it would
make it trivial to use device tree OF connections on existing gpiolib
controller drivers.
This patch eliminates the of_gpio_chip structure and moves the relevant
fields into struct gpio_chip (conditional on CONFIG_OF_GPIO). This move
simplifies the existing code and prepares for adding automatic device tree
support to existing drivers.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Bill Gatliff <bgat@billgatliff.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jean Delvare <khali@linux-fr.org>
Hopefully it makes the code look nicer and makes it easier to extend
this function.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CC: devicetree-discuss@lists.ozlabs.org
CC: linux-kernel@vger.kernel.org
Update Kconfig and Makefile in drivers/gpio to discourage inappropriate
addition of platform-specific code.
[akpm@linux-foundation.org: fix tpyo]
Signed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rdc_gpio_set_value_impl has the gpio data registers 1 and 2 inverted, fix this.
Signed-off-by: Bernhard Loos <bernhardloos@gmail.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The rdc321x southbridge PCI device has no MEM PCI resources that we could
pass to mfd_add_devices. Since 33254dd5, mfd_add_device checks for the
mem_base argument that we set to NULL. Changing the resources passed to
our MFD cells from IORESOURCE_MEM to IORESOURCE_IO fixes that. Since we use
those resources as offsets to the PCI configuration space base address of
the southbridge device this is also more adequate.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix rdc321x-southbridge build: GPIO_RDC321X needs to select
MFD_CORE so that the core is built at the same (or higher)
tristate level.
rdc321x-southbridge.c:(.devinit.text+0x6103): undefined reference to `mfd_add_devices'
rdc321x-southbridge.c:(.devexit.text+0xe5f): undefined reference to `mfd_remove_devices'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add a GPIO driver to support the GPIOs on the TC35892 I/O Expander.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Implicit slab.h inclusion via percpu.h is about to go away. Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The Janz VMOD-TTL is a MODULbus daughterboard which fits onto any MODULbus
carrier board. It essentially consists of some various logic and a Zilog
Z8536 CIO Counter/Timer and Parallel IO Unit.
The board must be physically configured with jumpers to enable a user to
drive output signals. I am only interested in outputs, so I have made this
driver as simple as possible. It only supports a very minimal subset of the
features provided by the Z8536 chip.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds a new GPIO driver for the RDC321x SoC GPIO controller.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This eliminates the following build warning:
drivers/gpio/it8761e_gpio.c: In function `it8761e_gpio_exit':
drivers/gpio/it8761e_gpio.c:220: warning: ignoring return value of `gpiochip_remove', declared with attribute warn_unused_result
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Intel Penwell chip has two 96 pins GPIO blocks, which are very similiar as
Intel Langwell chip GPIO block, except for pin number difference. This
patch expends the original Langwell GPIO driver to support Penwell's.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A few architectures, like OMAP, allow you to set a debouncing time for the
gpio before generating the IRQ. Teach gpiolib about that.
Mark said:
: This would be generally useful for embedded systems, especially where
: the interrupt concerned is a wake source. It allows drivers to avoid
: spurious interrupts from noisy sources so if the hardware supports it
: the driver can avoid having to explicitly wait for the signal to become
: stable and software has to cope with fewer events. We've lived without
: it for quite some time, though.
David said:
: I looked at adding debounce support to the generic GPIO calls (and thus
: gpiolib) some time back, but decided against it. I forget why at this
: time (check list archives) but it wasn't because of lack of utility in
: certain contexts.
:
: One thing to watch out for is just how variable the hardware capabilities
: are. Atmel GPIOs have something like a fixed number of 32K clock cycles
: for debounce, twl4030 had something odd, OMAPs were more like the Atmel
: chips but with a different clock. In some cases debouncing had to be
: ganged, not per-GPIO. And so forth.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <david-b@pacbell.net>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current message, 'not registered' is confusing as it implies it was
not registered with something, whereas printing 'failed to register'
implies it was the gpiochip_add() call that did not work correctly.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a bug I noticed while hacking on the max732x driver for interrupt
support. According to the datasheets, open-drain pins have to be
configured as output-high (which in that case is actually high impedance)
to be used as input.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Setup both client_group_a and client_group_b if nr_port > 8 (not including
nr_port==8).
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The valid offset value is 0..PL061_GPIO_NR-1, this patch corrects the
offset value range checking.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gpiolib doesn't need to modify the names and I assume most initializers
use string constants that shouldn't be modified anyhow.
[akpm@linux-foundation.org: fix drivers/gpio/cs5535-gpio.c]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Kevin Wells <kevin.wells@nxp.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most of the GPIO expanders supported by the max732x driver have interrupt
generation capability by reporting changes on input pins through an INT#
pin. This patch implements the irq_chip functionnality (edge detection
only).
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jebediah Huang <jebediah.huang@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merging in current state of Linus' tree to deal with merge conflicts and
build failures in vio.c after merge.
Conflicts:
drivers/i2c/busses/i2c-cpm.c
drivers/i2c/busses/i2c-mpc.c
drivers/net/gianfar.c
Also fixed up one line in arch/powerpc/kernel/vio.c to use the
correct node pointer.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The problem. When implementing a network namespace I need to be able
to have multiple network devices with the same name. Currently this
is a problem for /sys/class/net/*, /sys/devices/virtual/net/*, and
potentially a few other directories of the form /sys/ ... /net/*.
What this patch does is to add an additional tag field to the
sysfs dirent structure. For directories that should show different
contents depending on the context such as /sys/class/net/, and
/sys/devices/virtual/net/ this tag field is used to specify the
context in which those directories should be visible. Effectively
this is the same as creating multiple distinct directories with
the same name but internally to sysfs the result is nicer.
I am calling the concept of a single directory that looks like multiple
directories all at the same path in the filesystem tagged directories.
For the networking namespace the set of directories whose contents I need
to filter with tags can depend on the presence or absence of hotplug
hardware or which modules are currently loaded. Which means I need
a simple race free way to setup those directories as tagged.
To achieve a reace free design all tagged directories are created
and managed by sysfs itself.
Users of this interface:
- define a type in the sysfs_tag_type enumeration.
- call sysfs_register_ns_types with the type and it's operations
- sysfs_exit_ns when an individual tag is no longer valid
- Implement mount_ns() which returns the ns of the calling process
so we can attach it to a sysfs superblock.
- Implement ktype.namespace() which returns the ns of a syfs kobject.
Everything else is left up to sysfs and the driver layer.
For the network namespace mount_ns and namespace() are essentially
one line functions, and look to remain that.
Tags are currently represented a const void * pointers as that is
both generic, prevides enough information for equality comparisons,
and is trivial to create for current users, as it is just the
existing namespace pointer.
The work needed in sysfs is more extensive. At each directory
or symlink creating I need to check if the directory it is being
created in is a tagged directory and if so generate the appropriate
tag to place on the sysfs_dirent. Likewise at each symlink or
directory removal I need to check if the sysfs directory it is
being removed from is a tagged directory and if so figure out
which tag goes along with the name I am deleting.
Currently only directories which hold kobjects, and
symlinks are supported. There is not enough information
in the current file attribute interfaces to give us anything
to discriminate on which makes it useless, and there are
no potential users which makes it an uninteresting problem
to solve.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following structure elements duplicate the information in
'struct device.of_node' and so are being eliminated. This patch
makes all readers of these elements use device.of_node instead.
(struct of_device *)->node
(struct dev_archdata *)->prom_node (sparc)
(struct dev_archdata *)->of_node (powerpc & microblaze)
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The SIO chip contains 16 possible gpio lines, not 14. The schematic was
not read carefully.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.secretlab.ca/git/linux-2.6:
spi: spidev_test gives error upon 1-byte transfer
omap2_mcspi: small fixes of output data format
omap2_mcspi: Flush posted writes
spi: spi_device memory should be released instead of device.
spi: release device claimed by bus_find_device_by_name
of: check for IS_ERR()
serial/mpc52xx_uart: Drop outdated comments
gpio: potential null dereference
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6061/1: PL061 GPIO: Bug fix - setting gpio for HIGH_LEVEL interrupt is not working.
ARM: 5957/1: ARM: RealView SD/MMC Card detection and write-protect using GPIOLIB
ARM: 6030/1: KS8695: enable console
ARM: 6060/1: PL061 GPIO: Setting gpio val after changing direction to OUT.
ARM: 6059/1: PL061 GPIO: Changing *_irq_chip_data with *_irq_data for real irqs.
ARM: 6023/1: update bcmring_defconfig to latest version and fix build error
ARM: fix build error in arch/arm/kernel/process.c
In current implementation of PL061, setting type of irq to HIGH_LEVEL is not
working. This patch fixes this bug.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Smatch found a potential null dereference in gpio_setup_irq(). The
"pdesc" variable is allocated with idr_find() that can return NULL. If
gpio_setup_irq() is called with 0 as gpio_flags and "pdesc" is null, it
would OOPs here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Bill Gatliff reported the following bug when using the irq_chip facility
of the pca953x driver on a PPC platform:
BUG: scheduling while atomic: insmod/1530/0x00000002
He traced it back to an i2c transaction in pca953x_irq_set_type(), which
can be called with interrupt disabled (from __setup_irq()). As the i2c
controller can sleep while sending a message, this qualifies as a bad
idea.
This patch moves the i2c transaction to pca953x_irq_bus_sync_unlock(),
where it is actually safe to send an i2c message.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Reported-by: Bill Gatliff <bgat@billgatliff.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pl061_direction_output doesn't set value of gpio to value passed to it.
This patch sets value of GPIO pin to requested value after changing direction
to OUT.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
PL061 driver is using set_irq_chip_data and get_irq_chip_data for real
irq lines. It must be using *_irq_data functions instead. As chip_data
is used by interrupt controllers also, which makes vic write at incorrect
addresses.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In an error handling case the lock is not unlocked. The return is
converted to a goto, to share the unlock at the end of the function.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E1;
identifier f;
@@
f (...) { <+...
* spin_lock_irqsave (E1,...);
... when != E1
* return ...;
...+> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: <richard.rojfors@pelagicore.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
According to the header in max730x it is licensed GPLv2.
Add a MODULE_LICENSE to avoid getting the kernel tainted.
[w.sang@pengutronix.de: add MODULE_AUTHOR and MODULE_DESCRIPTION also]
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Passing the attribute to the low level IO functions allows all kinds
of cleanups, by sharing low level IO code without requiring
an own function for every piece of data.
Also drivers can extend the attributes with own data fields
and use that in the low level function.
This makes the class attributes the same as sysdev_class attributes
and plain attributes.
This will allow further cleanups in drivers.
Full tree sweep converting all users.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
LPC_SCH is selected by GPI_SCH and I2C_ISCH, even when PCI is not
enabled, but LPC_SCH depends on PCI, so make GPI_SCH and I2C_ISCH
also depend on PCI.
Those 2 selects also need to select what LPC_SCH selects,
since kconfig does not follow selects.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is the chip default but it's possible the bootloader or OTP
will have been configured to a different mode (eg, to provide
feedback during startup).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Revision B of the WM831x devices changes the sense of the tristate
bit for GPIO configuration, inverting it to become an enable instead.
Take account of this in the gpiolib driver.
A current sink regulation status bit has also been added in revision B,
add a flag indicating if it's present but don't use it yet.
This revision also adds an interrupt on key up for the ON pin event
which the existing code is able to take advantage of.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
wm831x_gpio_direction_output() ignored the state passed into it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The cs5535-gpio driver's get() function was returning the output value.
This means that the GPIO pins would never work as an input, even if
configured as an input.
The driver should return the READ_BACK value, which is the sensed line
value. To make that work when the direction is 'output', INPUT_ENABLE
needs to be set.
In addition, the driver was not disabling OUTPUT_ENABLE when the direction
is set to 'input'. That would cause the GPIO to continue to drive the pin
if the direction was ever set to output.
This issue was noticed when attempting to use the gpiolib driver to read
an external input. I had previously been using the char/cs5535-gpio
driver.
Signed-off-by: Ben Gardner <gardner.ben@gmail.com>
Acked-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: <stable@kernel.org> [2.6.33.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most of the GPIO expanders controlled by the pca953x driver are able to
report changes on the input pins through an *INT pin.
This patch implements the irq_chip functionality (edge detection only).
The driver has been tested on an Arcom Zeus.
[akpm@linux-foundation.org: the compiler does inlining for us nowadays]
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Nate Case <ncase@xes-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce support for triggering interrupts on both rising and falling
edge.
This feature requires version 3 or newer of the IP, a version check is
done when triggering on both edges is requested.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gpio_request() without initial configuration of the GPIO is normally
useless, introduce gpio_request_one() together with GPIOF_ flags for
input/output direction and initial output level.
gpio_{request,free}_array() for multiple GPIOs.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the MAX7300-I2C variant of the MAX7301-SPI version. Both chips share
the same core logic, so the generic part of the in-kernel SPI-driver is
refactored into a generic part. The I2C and SPI specific funtions are
then wrapped into seperate drivers picking up the generic part.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Juergen Beisert <j.beisert@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename for_each_bit to for_each_set_bit in the kernel source tree. To
permit for_each_clear_bit(), should that ever be added.
The patch includes a macro to map the old for_each_bit() onto the new
for_each_set_bit(). This is a (very) temporary thing to ease the migration.
[akpm@linux-foundation.org: add temporary for_each_bit()]
Suggested-by: Alexey Dobriyan <adobriyan@gmail.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Artem Bityutskiy <dedekind@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use of get_irq_chip_data() et al. requires including linux/irq.h
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously enabled poll(2) support on one edge was never reconfigured when
sysfs polarity change was triggered from kernel, because 'struct device
*dev' shadowed an earlier definition.
Found by sparse, which I should've run much earlier.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drivers may use gpiolib sysfs as part of their public user space
interface. The GPIO number and polarity might change from board to
board. The gpio_export_link() call can be used to hide the GPIO number
from user space. Add support for also hiding the GPIO line polarity
changes from user space.
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A GPIO driver for the Timberdale FPGA found on the Intel Atom board
Russellville.
The GPIO driver also has an IRQ-chip to support interrupts on the pins.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The wrong test was used, gpio is unsigned and it had an off-by-one.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Alek Du <alek.du@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With generic modular drivers handling all of this stuff, the
geode-specific code can go away. The cs5535-gpio, cs5535-mfgpt, and
cs5535-clockevt drivers now handle this.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changed number of gpio pins to 32 (according to datasheet)
Added mask to disable some pins
Added gpio_request for checking mask and disabling special pin functions
Added pin names
[dilinger@collabora.co.uk: make printk usage consistent]
Signed-off-by: Tobias Mueller <Tobias_Mueller@twam.info>
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This creates a CS5535/CS5536 GPIO driver which uses a gpio_chip backend
(allowing GPIO users to use the generic GPIO API if desired) while also
allowing architecture-specific users directly (via the cs5535_gpio_*
functions).
Tested on an OLPC machine. Some Leemotes also use CS5536 (with a mips
cpu), which is why this is in drivers/gpio rather than arch/x86.
Currently, it conflicts with older geode GPIO support; once MFGPT support
is reworked to also be more generic, the older geode code will be removed.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: David Brownell <david-b@pacbell.net>
Reviewed-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch renames function names like twl4030_i2c_write_u8,
twl4030_i2c_read_u8 to twl_i2c_write_u8, twl_i2c_read_u8
and also common variable in twl-core.c
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.
This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The common adp5520 mfd defines were namespaced to avoid collisions, so
update the define used in this driver accordingly. The structs were also
renamed to fix a spelling typo.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This supports future devices with fewer GPIOs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
- Remove wrong and unnecessary unmask operation
- Remove extra GEDR reading
This fixes the loss of interrupts which occurs when two or more pins are
triggered in close succession.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In case of failure, device_create() returns not NULL but the error code.
The current code checks for non-NULL though which causes kernel oops in
sysfs_create_group() when device_create() fails. Check for error using
IS_ERR() and propagate the error value using PTR_ERR() instead of fixed
-ENODEV code returned now...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The gpio_twl4030_probe() function calls gpio_twl4030_remove(), and the
former has __devinit, so the latter cannot use __devexit. Otherwise we
hit the section mismatch warning:
WARNING: drivers/gpio/built-in.o(.devinit.text+0x71a): Section mismatch
in reference from the function _gpio_twl4030_probe() to the function
.devexit.text:_gpio_twl4030_remove()
The function __devinit _gpio_twl4030_probe() references a function
__devexit _gpio_twl4030_remove().
This is often seen when error handling in the init function uses
functionality in the exit path.
The fix is often to remove the __devexit annotation of
_gpio_twl4030_remove() so it may be used outside an exit section.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Clearly mark ACPI drivers as such
i2c: Add driver for SMBus Control Method Interface
i2c-pnx: Correct use of request_region/request_mem_region
MAINTAINERS: Add maintainer for AT24 and PCA9564/PCA9665
i2c-piix4: Add AMD SB900 SMBus device ID
i2c/chips: Remove deprecated pcf8574 driver
i2c/chips: Remove deprecated pca9539 driver
i2c/chips: Remove deprecated pcf8575 driver
gpio/pcf857x: Copy i2c_device_id from old pcf8574 driver
i2c/scx200_acb: Provide more information on bus errors
i2c: Provide compatibility links for i2c adapters
i2c: Convert i2c adapters to bus devices
i2c: Convert i2c clients to a device type
i2c/tsl2550: Use combined SMBus transactions
i2c-taos-evm: Switch echo off to improve performance
i2c: Drop unused i2c_driver.id field
Many gpio chips allow to generate interrupts when the value of a pin
changes. This patch gives usermode application the opportunity to make
use of this feature by calling poll(2) on the /sys/class/gpio/gpioN/value
sysfs file. The edge to trigger can be set in the edge file in the same
directory. Possible values are "none", "rising", "falling", and "both".
Using level triggers is not possible with current sysfs since nothing
changes the GPIO value (and the IRQ keeps triggering). Edge triggering
will "just work". Note that if there was an event between read() and
poll(), the poll() returns immediately.
Also note that this version only supports true GPIO interrupts. Some
later patch might be able to synthesize this behavior by timer-driven
polling; some systems seem to need that.
[dbrownell@users.sourceforge.net: align ids to 16 bit ids; whitespace]
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drivers should be including <linux/gpio.h> not <asm/gpio.h>.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MAX7315 is pin and software compatible with PCA9534, so add it to the I2C
device ID table of pca953x driver.
http://www.datasheetcatalog.org/datasheet/maxim/MAX7315.pdf
Signed-off-by: Alek Du <alek.du@intel.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Langwell chip is the IO hub for Intel Moorestown platform which has a
64-pin gpio block device inside. It is exposed as a dedicated PCI device.
We use it to control outside peripheral as well as to do IRQ demuxing.
The gpio block uses MSI to send level type interrupt to IOAPIC.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Cc: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A GPIO driver for the Freescale MC33880 High/Low side switch
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 926b663ce8 (gpiolib: allow GPIOs to
be named) already provides naming on the chip level. This patch provides
more flexibility by allowing multiple names where ever in sysfs on a per
GPIO basis.
Adapted from David Brownell's comments on a similar concept:
http://lkml.org/lkml/2009/4/20/203.
[randy.dunlap@oracle.com: fix build for CONFIG_GENERIC_GPIO=n]
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Daniel Silverstone <dsilvers@simtec.co.uk>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes it consistent with other buses (platform, i2c, vio, ...). I'm
not sure why we use the prefixes, but there must be a reason.
This was easy enough to do it, and I did it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trivial patch which adds the __init/__exit macro to the init/exit functions of
drivers/gpio/bt8xxgpio.c
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The deprecated pcf8574 driver is going to be removed. Make sure the
replacement driver inherits all i2c_device_ids for a smooth transition.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the GPIO pins on the WM831x. No direct support is
currently supplied for configuring non-gpiolib functionality such
as pull configuration and alternate functions, soft configuration
of these will be provided in a future patch.
Currently use of these pins as interrupts is not supported due to
the ongoing issues with generic irq not support interrupt controllers
on interrupt driven buses. Users can directly request the interrupts
with the wm831x-specific APIs currently provided if required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IRQ handling is wrong for any GPIO >= PL061_GPIO_NR.
Fix this by implementing and using a proper .to_irq method.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Note that IRQ has not been initialized when kmalloc() fails.
Also, use DECLARE_BITMAP() to make the code clearer.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a driver for the ARM PrimeCell PL061 GPIO AMBA peripheral. The
driver is implemented using the gpiolib framework.
This driver also includes support for the use of the PL061 as an interrupt
controller (secondary).
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PCA9556 is the software-compatible predecessor to the PCA9557, so add it
to the supported I2C device ID table.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On OpenFirmware platforms, it makes the most sense to get platform_data
from the device tree. Make an attempt to translate OF node properties
into platform_data struct before bailing out.
Note that the implementation approach taken differs from other device
drivers that make use of device tree information. This is because I2C
chips are already registered automatically by of_i2c, so we can get by
with a small translator function in the driver.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: kfree(NULL) is legal]
Signed-off-by: Nate Case <ncase@xes-inc.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The remove member of the spi_driver max7301_driver uses __devexit_p(), so
the remove function itself should be marked with __devexit. Even more so
considering the probe function is marked with __devinit.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Juergen Beisert <j.beisert@pengutronix.de>
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support to the PCA953x driver to use the GPIOLIB naming facility for
GPIOs.
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
We want to phase out the GPIO "autorequest" mechanism in gpiolib and
require all callers to use gpio_request().
- Update feature-removal-schedule
- Update the documentation now
- Convert the relevant pr_warning() in gpiolib to a WARN()
so folk using this mechanism get a noisy stack dump
Some drivers and board init code will probably need to change.
Implementations not using gpiolib will still be fine; they are already
required to implement gpio_{request,free}() stubs.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow GPIOs in GPIOLIB chips to be named. This name is then used when the
GPIO is exported to sysfs, although it could be used elsewhere if deemed
useful.
Signed-off-by: Daniel Silverstone <dsilvers@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A number of drivers in drivers/gpio return -ENODEV when confronted with
missing setup parameters such as the platform data. However, returning
-ENODEV causes the driver layer to silently ignore the driver as it
assumes the probe did not find anything and was only speculative.
To make life easier to discern why a driver is not being attached, change
to returning -EINVAL, which is a better description of the fact that the
driver data was not valid.
Also add a set of dev_dbg() statements to the error paths to provide an
better explanation of the error as there may be more that one point in the
driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor updates to the pca953x GPIO expander driver: handle several more
compatible parts, and stop assuming that the I2C layer's return codes are
garbage (that's now been fixed).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide a static debounce configuration mechanism for twl4030 GPIOs,
replacing the previous dynamic one. The single user of that mechanism was
for MMC card detect debouncing.
Boards can provide a bitmask saying which GPIOs to debounce (30 msec).
It's always enabled for pins with the MMC card-detect/VMMCx link active,
so most boards won't need to set the debounce mask.
This is a net code shrink, including runtime footprint.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are already various drivers having bigger label than 12 bytes. Most
of them fit well under 20 bytes but make column width exact so that
oversized labels don't mess up output alignment.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: <stable@kernel.org> [2.6.26.x, 2.6.26.x, 2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver supports the Xilinx XPS GPIO IP core which has the typical
GPIO features.
Signed-off-by: Kiran Sutariya <kirans@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: "Grant Likely" <grant.likely@secretlab.ca>
Cc: <avorontsov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds basic support for the GPIOs in the twl4030 power management
chip. That includes two open drain LED drivers, and the use of GPIO-0
(and GPIO-1) as MMC/SD card detect switches which can control whether
the VMMC1 (and VMMC2) regulators are active.
This version of the code has a debounce call that will probably be
replaced before long, when a more generic interface exists.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This merges branches irq/genirq, irq/sparseirq-v4, timers/hpet-percpu
and x86/uv.
The sparseirq branch is just preliminary groundwork: no sparse IRQs are
actually implemented by this tree anymore - just the new APIs are added
while keeping the old way intact as well (the new APIs map 1:1 to
irq_desc[]). The 'real' sparse IRQ support will then be a relatively
small patch ontop of this - with a v2.6.29 merge target.
* 'genirq-v28-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (178 commits)
genirq: improve include files
intr_remapping: fix typo
io_apic: make irq_mis_count available on 64-bit too
genirq: fix name space collisions of nr_irqs in arch/*
genirq: fix name space collision of nr_irqs in autoprobe.c
genirq: use iterators for irq_desc loops
proc: fixup irq iterator
genirq: add reverse iterator for irq_desc
x86: move ack_bad_irq() to irq.c
x86: unify show_interrupts() and proc helpers
x86: cleanup show_interrupts
genirq: cleanup the sparseirq modifications
genirq: remove artifacts from sparseirq removal
genirq: revert dynarray
genirq: remove irq_to_desc_alloc
genirq: remove sparse irq code
genirq: use inline function for irq_to_desc
genirq: consolidate nr_irqs and for_each_irq_desc()
x86: remove sparse irq from Kconfig
genirq: define nr_irqs for architectures with GENERIC_HARDIRQS=n
...
We can get the following oops from gpio_get_value_cansleep() when a GPIO
controller doesn't provide a get() callback:
Unable to handle kernel paging request for instruction fetch
Faulting instruction address: 0x00000000
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [00000000] 0x0
LR [c0182fb0] gpio_get_value_cansleep+0x40/0x50
Call Trace:
[c7b79e80] [c0183f28] gpio_value_show+0x5c/0x94
[c7b79ea0] [c01a584c] dev_attr_show+0x30/0x7c
[c7b79eb0] [c00d6b48] fill_read_buffer+0x68/0xe0
[c7b79ed0] [c00d6c54] sysfs_read_file+0x94/0xbc
[c7b79ef0] [c008f24c] vfs_read+0xb4/0x16c
[c7b79f10] [c008f580] sys_read+0x4c/0x90
[c7b79f40] [c0013a14] ret_from_syscall+0x0/0x38
It's OK to request the value of *any* GPIO; most GPIOs are bidirectional,
so configuring them as outputs just enables an output driver and doesn't
disable the input logic.
So the problem is that gpio_get_value_cansleep() isn't making the same
sanity check that gpio_get_value() does: making sure this GPIO isn't one
of the atypical "no input logic" cases.
Reported-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: <stable@kernel.org> [2.6.27.x, 2.6.26.x, 2.6.25.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gpiolib can export GPIOs to userspace via sysfs. This patch modifies the
gpio_value_show() so that any non-zero value is explicitly printed as "1",
rather than whatever numerical value the lower-level driver returns.
Signed-off-by: Steve Falco <sfalco@harris.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new internal mechanism to gpiolib to support low power
operations by letting gpio_chip instances see when their GPIOs
are in use. When no GPIOs are active, chips may be able to
enter lower powered runtime states by disabling clocks and/or
power domains.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: "Magnus Damm" <magnus.damm@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new gpiolib mechanism: gpio_chip instances can provide mappings
between their (input) GPIOs and any associated IRQs. This makes it easier
for platforms to support IRQs that are provided by board-specific external
chips instead of as part of their core (such as SOC-integrated GPIOs).
Also update the irq_to_gpio() description, saying to avoid it because it's
not always supported.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the I2C external GPIO expander drivers register themselves at
subsys_initcall() time when they're statically linked.
SOC-integrated GPIOs are available starting very early -- early in
arch_initcall() at latest, but often even before initcalls start to run --
so this improves consistency, so more subsystems can rely on GPIOs in
their own subsys_initcall() code.
(This isn't a theoretical problem. This is one of several patches needed
to resolve oopsing observed when statically linking kernels on a DaVinci
EVM. Its pcf857x GPIOs needed to be available well before some other
drivers initialized.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to the documentation gpio_free should only be called from task
context only. To make this more explicit add a might sleep to all
implementations.
This is the generic part which changes gpiolib and the fallback
implementation only.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a small race and code ugliness in max7301: pins are reconfigured
after the chip is registered. Swap these calls so that the device is
registered in correct state.
Also this fixes the comile-time warning about unchecked gpiochip_remove.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Juergen Beisert <j.beisert@pengutronix.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the SPI external GPIO expander drivers register themselves at
subsys_initcall() time when they're statically linked, and make the SPI
core do its driver model initialization earlier so that's safe.
SOC-integrated GPIOs are available starting very early -- often before
initcalls start to run, or earily in arch_initcall() at latest -- so this
improves consistency, letting more subsystems rely on GPIOs being usable
by their own subsys_initcall() code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
add CONFIG_HAVE_SPARSE_IRQ to for use condensed array.
Get rid of irq_desc[] array assumptions.
Preallocate 32 irq_desc, and irq_desc() will try to get more.
( No change in functionality is expected anywhere, except the odd build
failure where we missed a code site or where a crossing commit itroduces
new irq_desc[] usage. )
v2: according to Eric, change get_irq_desc() to irq_desc()
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This adds a driver supporting a family of I2C port expanders from Maxim,
which includes the MAX7319 and MAX7320-7327 chips.
[dbrownell@users.sourceforge.net: minor fixes]
Signed-off-by: Jack Ren <jack.ren@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds functionality to the gpio-lib subsystem to make it
possible to enable the gpio-lib code even if the architecture code didn't
request to get it built in.
The archtitecture code does still need to implement the gpiolib accessor
functions in its asm/gpio.h file. This patch adds the implementations for
x86 and PPC.
With these changes it is possible to run generic GPIO expansion cards on
every architecture that implements the trivial wrapper functions. Support
for more architectures can easily be added.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds the bt8xxgpio driver. The purpose of the bt8xxgpio driver is to
export all of the 24 GPIO pins available on Brooktree 8xx chips to the
kernel GPIO infrastructure.
This makes it possible to use a physically modified BT8xx card as
cheap digital GPIO card.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Teach the mcp23s08 driver about a curious feature of these chips: up to
four of them can share the same chipselect, with the SPI signals wired in
parallel, by matching two bits in the first protocol byte against two
address lines on the chip.
This is handled by three software changes:
* Platform data now holds an array of per-chip structs, not
just one chip's address and pullup configuration.
* Probe() and remove() now use another level of structure,
wrapping an instance of the original structure for each
mcp23s08 chip sharing that chipselect.
* The HAEN bit is set, so that the hardware address bits can no
longer be ignored (boot firmware may not have enabled them).
The "one struct per chip" preserves the guts of the current code,
but platform_data will need minor changes.
OLD:
/* incorrect "slave" ID may not have mattered */
.slave = 3,
.pullups = BIT(3) | BIT(1) | BIT(0),
NEW:
/* slave address _must_ match chip's wiring */
.chip[3] = {
.is_present = true,
.pullups = BIT(3) | BIT(1) | BIT(0),
},
There's no change in how things _behave_ for spi_device nodes with a
single mcp23s08 chip. New multi-chip configurations assign GPIOs in
sequence, without holes. The spi_device just resembles a bigger
controller, but internally it has multiple gpio_chip instances.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a simple sysfs interface for GPIOs.
/sys/class/gpio
/export ... asks the kernel to export a GPIO to userspace
/unexport ... to return a GPIO to the kernel
/gpioN ... for each exported GPIO #N
/value ... always readable, writes fail for input GPIOs
/direction ... r/w as: in, out (default low); write high, low
/gpiochipN ... for each gpiochip; #N is its first GPIO
/base ... (r/o) same as N
/label ... (r/o) descriptive, not necessarily unique
/ngpio ... (r/o) number of GPIOs; numbered N .. N+(ngpio - 1)
GPIOs claimed by kernel code may be exported by its owner using a new
gpio_export() call, which should be most useful for driver debugging.
Such exports may optionally be done without a "direction" attribute.
Userspace may ask to take over a GPIO by writing to a sysfs control file,
helping to cope with incomplete board support or other "one-off"
requirements that don't merit full kernel support:
echo 23 > /sys/class/gpio/export
... will gpio_request(23, "sysfs") and gpio_export(23);
use /sys/class/gpio/gpio-23/direction to (re)configure it,
when that GPIO can be used as both input and output.
echo 23 > /sys/class/gpio/unexport
... will gpio_free(23), when it was exported as above
The extra D-space footprint is a few hundred bytes, except for the sysfs
resources associated with each exported GPIO. The additional I-space
footprint is about two thirds of the current size of gpiolib (!). Since
no /dev node creation is involved, no "udev" support is needed.
Related changes:
* This adds a device pointer to "struct gpio_chip". When GPIO
providers initialize that, sysfs gpio class devices become children of
that device instead of being "virtual" devices.
* The (few) gpio_chip providers which have such a device node have
been updated.
* Some gpio_chip drivers also needed to update their module "owner"
field ... for which missing kerneldoc was added.
* Some gpio_chips don't support input GPIOs. Those GPIOs are now
flagged appropriately when the chip is registered.
Based on previous patches, and discussion both on and off LKML.
A Documentation/ABI/testing/sysfs-gpio update is ready to submit once this
merges to mainline.
[akpm@linux-foundation.org: a few maintenance build fixes]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Two small updates to the pcf857x driver: (a) the max732[89] chips are
also second sources for the pcf8574/a, and (b) add a mutex to prevent
trashing the cached state. Adding the lock is effectively a bugfix,
although it seems unlikely that anyone would have run into the issue it
protects against.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Maxim's MAX7301 is an SPI GPIO expander with 28 GPIOs. Note: MAX7301's
interrupt feature is not supported yet.
[akpm@linux-foundation.org: coding-style fixes]
[g.liakhovetski@pengutronix.de: Fix inaccuracies in comments, check spi_setup()
return code, mask off high byte in max7301_read()]
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pca953x driver can handle another 8-bit I/O expander, the max7310.
This patch adds that chip to the list of supported IDs in that driver, and
expands the Kconfig helptext accordingly.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The last gpio belonging to a chip is chip->base + chip->ngpios - 1. Some
places in the code, but not all, forgot the critical minus one.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The return value of mcp23s08_read_regs() can only be evaluated when signed
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Teach drivers/gpio/pca953x.c about PCA9554, another compatible chip.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for pca9555 I2C I/O expander. As the comment suggests this part
is software compatible with the pca9539.
Signed-off-by: Will Newton <will.newton@imgtec.com>
Cc: "eric miao" <eric.miao@marvell.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on earlier work by Jon Smirl and Jochen Friedrich.
Update most new-style i2c drivers to use standard module aliasing
instead of the old driver_name/type driver matching scheme. I've
left the video drivers apart (except for SoC camera drivers) as
they're a bit more diffcult to deal with, they'll have their own
patch later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Jochen Friedrich <jochen@scram.de>
Based on earlier work by Jon Smirl and Jochen Friedrich.
This patch allows new-style i2c chip drivers to have alias names using
the official kernel aliasing system and MODULE_DEVICE_TABLE(). At this
point, the old i2c driver binding scheme (driver_name/type) is still
supported.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jochen Friedrich <jochen@scram.de>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Add a new function gpiochip_reserve() to reserve ranges of gpios that platform
code has pre-allocated. That is, this marks gpio numbers which will be
claimed by drivers that haven't yet been loaded, and thus are not available
for dynamic gpio number allocation.
[akpm@linux-foundation.org: remove unneeded __must_check]
[david-b@pacbell.net: don't export gpiochip_reserve (section fix)]
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If gpio_chip->base is negative during registration, gpiolib performs dynamic
base allocation. This is useful for devices that aren't always present, such
as GPIOs on hotplugged devices rather than mainboards. (This behavior was
previously specified but not implemented.)
To avoid using any numbers that may have been explicitly assigned but not yet
registered, this dynamic allocation assigns GPIO numbers from the biggest
number on down, instead of from the smallest on up.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce a gpio_is_valid() predicate; use it in gpiolib.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
[ use inline function; follow the gpio_* naming convention;
work without gpiolib; all programming interfaces need docs ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the newly introduced owner field in struct gpio_chip to protect the
current (small) set of non-SOC GPIO drivers from being unloaded while any of
their GPIOs are in use.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
[ add mcp23s08 and pcf857x ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As long as one or more GPIOs on a gpio chip are used its driver should not be
unloaded. The existing mechanism (gpiochip_remove failure) doesn't address
that, since rmmod can no longer be made to fail by having the cleanup code
report errors. Module usecounts are the solution.
Assuming standard "initialize struct to zero" policies, this change won't
affect SOC platform drivers. However, drivers for external chips (on I2C and
SPI busses) should be updated if they can be built as modules.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
[ gpio_ensure_requested() needs to update module usecounts too ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pca953x driver is an I2C driver so gpio_chip->can_sleep should be set.
This lets upper layers know they should use the gpio_*_cansleep() calls to
access values, and may not access them from nonsleeping contexts.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: "eric miao" <eric.y.miao@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This third part of an extension to support more pca953x chips updates the
logic to handle the smaller register widths used by the 4-bit and 8-bit parts,
and to use the chip type to determine how many GPIOs it provides.
As long as we don't support interrupt and reset capabilities, those size
issues are the only software-visible differences between these parts.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This second part of an extension to support more pca953x chips renames the C
and Kconfig symbols. All affected files were updated by sed, except for a
couple of obvious exceptions. It also updates the Kconfig helptext.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
First part of an extension to let the pca9539 driver support more chips,
starting with pca9534, pca9535, pca9536, pca9537, and pca9538.
This renames the files and modifies the Makefile.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a new-style I2C driver with basic support for the sixteen bit
PCA9539 GPIO expanders. These chips have multiple registers, push-pull output
drivers, and (not supported in this patch) pin change interrupts.
Board-specific code must provide "pca9539_platform_data" with each chip's
"i2c_board_info". That provides the GPIO numbers to be used by that chip, and
callbacks for board-specific setup/teardown logic.
Derived from drivers/i2c/chips/pca9539.c (which has no current known users).
This is faster and simpler; it uses 16-bit register access, and cache the
OUTPUT and DIRECTION registers for fast access
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Basic driver for 8-bit SPI based MCP23S08 GPIO expander, without support for
IRQs or the shared chipselect mechanism.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a new-style I2C driver for most common 8 and 16 bit I2C based
"quasi-bidirectional" GPIO expanders: pcf8574 or pcf8575, and several
compatible models (mostly faster, supporting I2C at up to 1 MHz).
The driver exposes the GPIO signals using the platform-neutral GPIO
programming interface, so they are easily accessed by other kernel code. The
lack of such a flexible kernel API has been a big factor in the proliferation
of board-specific drivers for these chips... stuff that rarely makes it
upstream since it's so ugly. This driver will let such boards use standard
calls.
Since it's a new-style driver, these devices must be configured as part of
board-specific init. That eliminates the need for error-prone manual
configuration of module parameters, and makes compatibility with legacy
drivers (pcf8574.c, pc8575.c) for these chips easier (there's a clear
either/or disjunction).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Provide new implementation infrastructure that platforms may choose to use
when implementing the GPIO programming interface. Platforms can update their
GPIO support to use this. In many cases the incremental cost to access a
non-inlined GPIO should be less than a dozen instructions, with the memory
cost being about a page (total) of extra data and code. The upside is:
* Providing two features which were "want to have (but OK to defer)" when
GPIO interfaces were first discussed in November 2006:
- A "struct gpio_chip" to plug in GPIOs that aren't directly supported
by SOC platforms, but come from FPGAs or other multifunction devices
using conventional device registers (like UCB-1x00 or SM501 GPIOs,
and southbridges in PCs with more open specs than usual).
- Full support for message-based GPIO expanders, where registers are
accessed through sleeping I/O calls. Previous support for these
"cansleep" calls was just stubs. (One example: the widely used
pcf8574 I2C chips, with 8 GPIOs each.)
* Including a non-stub implementation of the gpio_{request,free}() calls,
making those calls much more useful. The diagnostic labels are also
recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot
of all GPIOs known to this infrastructure.
The driver programming interfaces introduced in 2.6.21 do not change at all;
this infrastructure is entirely below those covers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an empty drivers/gpio directory for gpiolib infrastructure and GPIO
expanders. It will be populated by later patches.
This won't be the only place to hold such gpio_chip code. Many external chips
add a few GPIOs as secondary functionality (such as MFD drivers) and platform
code frequently needs to closely integrate GPIO and IRQ support.
This is placed *early* in the build/link sequence since it's common for other
drivers to depend on GPIOs to do their work, so they must be initialized early
in the device_initcall() sequence.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Gleixner