pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiawen Wu <jiawenwu@trustnetic.com>
Cc: Mengyuan Lou <mengyuanlou@net-swift.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiawen Wu <jiawenwu@trustnetic.com>
Cc: Mengyuan Lou <mengyuanlou@net-swift.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
51b35a454e ("sfc: skeleton EF100 PF driver") added a call to
pci_disable_pcie_error_reporting() in ef100_pci_remove().
Remove this call since there's no apparent reason to disable error
reporting when it was not previously enabled.
Note that since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core enables PCIe error reporting for all devices during
enumeration, so the driver doesn't need to do it itself.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Martin Habets <habetsm.xilinx@gmail.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Martin Habets <habetsm.xilinx@gmail.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Martin Habets <habetsm.xilinx@gmail.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Martin Habets <habetsm.xilinx@gmail.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shahed Shaikh <shshaikh@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Cc: GR-Linux-NIC-Dev@marvell.com
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ariel Elior <aelior@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Veerasenareddy Burru <vburru@marvell.com>
Cc: Abhijit Ayarekar <aayarekar@marvell.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Also note that the driver only called these for NX_IS_REVISION_P3 devices,
so since f26e58bf6f, error reporting has been enabled for devices other
than NX_IS_REVISION_P3.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Manish Chopra <manishc@marvell.com>
Cc: Rahul Verma <rahulv@marvell.com>
Cc: GR-Linux-NIC-Dev@marvell.com
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Dimitris Michailidis <dmichail@fungible.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Raju Rangoju <rajur@chelsio.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ariel Elior <aelior@marvell.com>
Cc: Sudarsana Kalluru <skalluru@marvell.com>
Cc: Manish Chopra <manishc@marvell.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
cd709aa906 ("bnx2: Add PCI Advanced Error Reporting support.") added
pci_enable_pcie_error_reporting() for all devices, and c239f279e5 ("bnx2:
Enable AER on PCIE devices only") restricted it to BNX2_CHIP_5709 devices
to avoid an error message when it failed on non-PCIe devices. The PCI core
only enables PCIe error reporting on PCIe devices, which I assume means
BNX2_CHIP_5709.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rasesh Mody <rmody@marvell.com>
Cc: GR-Linux-NIC-Dev@marvell.com
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
pci_enable_pcie_error_reporting() enables the device to send ERR_*
Messages. Since f26e58bf6f ("PCI/AER: Enable error reporting when AER is
native"), the PCI core does this for all devices during enumeration, so the
driver doesn't need to do it itself.
Remove the redundant pci_enable_pcie_error_reporting() call from the
driver. Also remove the corresponding pci_disable_pcie_error_reporting()
from the driver .remove() path.
Note that this only controls ERR_* Messages from the device. An ERR_*
Message may cause the Root Port to generate an interrupt, depending on the
AER Root Error Command register managed by the AER service driver.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Snook <chris.snook@gmail.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski says:
====================
tools: ynl: fix enum-as-flags in the generic CLI
The CLI needs to use proper classes when looking at Enum definitions
rather than interpreting the YAML spec ad-hoc, because we have more
than on format of the definition supported.
====================
Link: https://lore.kernel.org/r/20230308003923.445268-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lorenzo points out that the generic CLI is broken for the netdev
family. When I added the support for documentation of enums
(and sparse enums) the client script was not updated.
It expects the values in enum to be a list of names,
now it can also be a dict (YAML object).
Reported-by: Lorenzo Bianconi <lorenzo@kernel.org>
Fixes: e4b48ed460 ("tools: ynl: add a completely generic client")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
R-Car H3 ES1.* was only available to an internal development group and
needed a lot of quirks and workarounds. These become a maintenance
burden now, so our development group decided to remove upstream support
and disable booting for this SoC. Public users only have ES2 onwards.
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/all/20230307163041.3815-8-wsa+renesas@sang-engineering.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MT7530 switch from the MT7621 SoC has 2 ports which can be set up as
internal: port 5 and 6. Arınç reports that the GMAC1 attached to port 5
receives corrupted frames, unless port 6 (attached to GMAC0) has been
brought up by the driver. This is true regardless of whether port 5 is
used as a user port or as a CPU port (carrying DSA tags).
Offline debugging (blind for me) which began in the linked thread showed
experimentally that the configuration done by the driver for port 6
contains a step which is needed by port 5 as well - the write to
CORE_GSWPLL_GRP2 (note that I've no idea as to what it does, apart from
the comment "Set core clock into 500Mhz"). Prints put by Arınç show that
the reset value of CORE_GSWPLL_GRP2 is RG_GSWPLL_POSDIV_500M(1) |
RG_GSWPLL_FBKDIV_500M(40) (0x128), both on the MCM MT7530 from the
MT7621 SoC, as well as on the standalone MT7530 from MT7623NI Bananapi
BPI-R2. Apparently, port 5 on the standalone MT7530 can work under both
values of the register, while on the MT7621 SoC it cannot.
The call path that triggers the register write is:
mt753x_phylink_mac_config() for port 6
-> mt753x_pad_setup()
-> mt7530_pad_clk_setup()
so this fully explains the behavior noticed by Arınç, that bringing port
6 up is necessary.
The simplest fix for the problem is to extract the register writes which
are needed for both port 5 and 6 into a common mt7530_pll_setup()
function, which is called at mt7530_setup() time, immediately after
switch reset. We can argue that this mirrors the code layout introduced
in mt7531_setup() by commit 42bc4fafe3 ("net: mt7531: only do PLL once
after the reset"), in that the PLL setup has the exact same positioning,
and further work to consolidate the separate setup() functions is not
hindered.
Testing confirms that:
- the slight reordering of writes to MT7530_P6ECR and to
CORE_GSWPLL_GRP1 / CORE_GSWPLL_GRP2 introduced by this change does not
appear to cause problems for the operation of port 6 on MT7621 and on
MT7623 (where port 5 also always worked)
- packets sent through port 5 are not corrupted anymore, regardless of
whether port 6 is enabled by phylink or not (or even present in the
device tree)
My algorithm for determining the Fixes: tag is as follows. Testing shows
that some logic from mt7530_pad_clk_setup() is needed even for port 5.
Prior to commit ca366d6c88 ("net: dsa: mt7530: Convert to PHYLINK
API"), a call did exist for all phy_is_pseudo_fixed_link() ports - so
port 5 included. That commit replaced it with a temporary "Port 5 is not
supported!" comment, and the following commit 38f790a805 ("net: dsa:
mt7530: Add support for port 5") replaced that comment with a
configuration procedure in mt7530_setup_port5() which was insufficient
for port 5 to work. I'm laying the blame on the patch that claimed
support for port 5, although one would have also needed the change from
commit c3b8e07909 ("net: dsa: mt7530: setup core clock even in TRGMII
mode") for the write to be performed completely independently from port
6's configuration.
Thanks go to Arınç for describing the problem, for debugging and for
testing.
Reported-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/netdev/f297c2c4-6e7c-57ac-2394-f6025d309b9d@arinc9.com/
Fixes: 38f790a805 ("net: dsa: mt7530: Add support for port 5")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230307155411.868573-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEq1nRK9aeMoq1VSgcnJ2qBz9kQNkFAmQIrVcACgkQnJ2qBz9k
QNkG0gf/Z9O+5AKKGM3tGzO/IsQB+33S+cCSH6FVqIpV8rx6HJBUtUOU8bJBoA6r
yY/t9phD1ahOBDpeZKQPj9zL5R3LWf0Xf3LDbMNfx7lD0mRiM1QR1hSOPQ9Frze+
cydo1LQvtZ1U3Axs/26fNMRzBwF6a9l9X3YTvSHfpaEPuZwDPtDZAgT2ORE85gZv
faTXlTubc6qEsvkHS7JWwloFRgqjdE74mMcBIhSQizo2Z+QH14uXUQ36DuU6UlU7
bYQ5VBEN6kanKzR3gGcOkdb22k8SL91pvoK9nYhqOqlVi/ydc5KhuKeWoPXQ9DVT
mXrBxfH8fF7G2Q98N8EgRcdia6ksNQ==
=OBP7
-----END PGP SIGNATURE-----
Merge tag 'fs_for_v6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Pull udf fixes from Jan Kara:
"Fix bugs in UDF caused by the big pile of changes that went in during
the merge window"
* tag 'fs_for_v6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
udf: Warn if block mapping is done for in-ICB files
udf: Fix reading of in-ICB files
udf: Fix lost writes in udf_adinicb_writepage()
A small set of assorted bug and build/warning fixes for 6.3.
The following is an automated git shortlog grouped by driver:
ISST:
- Fix kernel documentation warnings
- Increase range of valid mail box commands
dell-ddv:
- Fix temperature scaling
- Fix cache invalidation on resume
int3472:
- Add GPIOs to Surface Go 3 Board data
platform:
- mellanox: mlx-platform: Initialize shift variable to 0
- x86: MLX_PLATFORM: select REGMAP instead of depending on it
- mellanox: select REGMAP instead of depending on it
platform/x86/amd:
- pmc: remove CONFIG_SUSPEND checks
platform/x86/intel/tpmi:
- Fix double free reported by Smatch
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmQIoP0UHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9y5Zwf/Zz46BKL5T8lp3fPnQj4UYn83daaL
tIn99ElMINzdCLVYK/9DWKfSqK4PHfgUIfIyhNpOoLMot34fKdC7KNAJGvSrReQO
rfYiA7ErArTHt9FzFG0F3hPkJ1KbyQwS/X+IAUw1gYyewrE4GTq0KSaSs0SGAtuq
UfzcpHquSSuA/A49Vr3yj7LBwGXbWz9JBuJv7Q6VpmsR4+7VgtdTJTKKycHgKLXT
eOdX5nRJ8vkC1lCUJ8CqESZ18edNVa5GqmlojRMP5Bv2kq0yGHG4SWoITAt/mcQC
K8XqbpPuw/Ijsv6iMJ/gOnbh5SYyesHkTBbu+b7VPlZ6zJwVxPFuG7alTg==
=w1A/
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v6.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fixes from Hans de Goede:
"A small set of assorted bug and build/warning fixes"
* tag 'platform-drivers-x86-v6.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform: mellanox: mlx-platform: Initialize shift variable to 0
platform/x86: int3472: Add GPIOs to Surface Go 3 Board data
platform/x86: ISST: Fix kernel documentation warnings
platform: x86: MLX_PLATFORM: select REGMAP instead of depending on it
platform: mellanox: select REGMAP instead of depending on it
platform/x86/intel/tpmi: Fix double free reported by Smatch
platform/x86: ISST: Increase range of valid mail box commands
platform/x86: dell-ddv: Fix temperature scaling
platform/x86: dell-ddv: Fix cache invalidation on resume
platform/x86/amd: pmc: remove CONFIG_SUSPEND checks
The implementation of 'current' on x86 is very intentionally special: it
is a very common thing to look up, and it uses 'this_cpu_read_stable()'
to get the current thread pointer efficiently from per-cpu storage.
And the keyword in there is 'stable': the current thread pointer never
changes as far as a single thread is concerned. Even if when a thread
is preempted, or moved to another CPU, or even across an explicit call
'schedule()' that thread will still have the same value for 'current'.
It is, after all, the kernel base pointer to thread-local storage.
That's why it's stable to begin with, but it's also why it's important
enough that we have that special 'this_cpu_read_stable()' access for it.
So this is all done very intentionally to allow the compiler to treat
'current' as a value that never visibly changes, so that the compiler
can do CSE and combine multiple different 'current' accesses into one.
However, there is obviously one very special situation when the
currently running thread does actually change: inside the scheduler
itself.
So the scheduler code paths are special, and do not have a 'current'
thread at all. Instead there are _two_ threads: the previous and the
next thread - typically called 'prev' and 'next' (or prev_p/next_p)
internally.
So this is all actually quite straightforward and simple, and not all
that complicated.
Except for when you then have special code that is run in scheduler
context, that code then has to be aware that 'current' isn't really a
valid thing. Did you mean 'prev'? Did you mean 'next'?
In fact, even if then look at the code, and you use 'current' after the
new value has been assigned to the percpu variable, we have explicitly
told the compiler that 'current' is magical and always stable. So the
compiler is quite free to use an older (or newer) value of 'current',
and the actual assignment to the percpu storage is not relevant even if
it might look that way.
Which is exactly what happened in the resctl code, that blithely used
'current' in '__resctrl_sched_in()' when it really wanted the new
process state (as implied by the name: we're scheduling 'into' that new
resctl state). And clang would end up just using the old thread pointer
value at least in some configurations.
This could have happened with gcc too, and purely depends on random
compiler details. Clang just seems to have been more aggressive about
moving the read of the per-cpu current_task pointer around.
The fix is trivial: just make the resctl code adhere to the scheduler
rules of using the prev/next thread pointer explicitly, instead of using
'current' in a situation where it just wasn't valid.
That same code is then also used outside of the scheduler context (when
a thread resctl state is explicitly changed), and then we will just pass
in 'current' as that pointer, of course. There is no ambiguity in that
case.
The fix may be trivial, but noticing and figuring out what went wrong
was not. The credit for that goes to Stephane Eranian.
Reported-by: Stephane Eranian <eranian@google.com>
Link: https://lore.kernel.org/lkml/20230303231133.1486085-1-eranian@google.com/
Link: https://lore.kernel.org/lkml/alpine.LFD.2.01.0908011214330.3304@localhost.localdomain/
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Tony Luck <tony.luck@intel.com>
Tested-by: Stephane Eranian <eranian@google.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 62622dab0a ("ima: return IMA digest value only when IMA_COLLECTED
flag is set") caused bpf_ima_inode_hash() to refuse to give non-fresh
digests. IMA test #3 assumed the old behavior, that bpf_ima_inode_hash()
still returned also non-fresh digests.
Correct the test by accepting both cases. If the samples returned are 1,
assume that the commit above is applied and that the returned digest is
fresh. If the samples returned are 2, assume that the commit above is not
applied, and check both the non-fresh and fresh digest.
Fixes: 62622dab0a ("ima: return IMA digest value only when IMA_COLLECTED flag is set")
Reported-by: David Vernet <void@manifault.com>
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Reviewed-by: Matt Bobrowski <mattbobrowski@google.com>
Link: https://lore.kernel.org/bpf/20230308103713.1681200-1-roberto.sassu@huaweicloud.com
A couple of arguments to a function call are incorrectly indented.
Fix them.
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
This test runs on the client-router-server topo, and monitors the traffic
on the RX devices of router and server while sending BIG TCP packets with
netperf from client to server. Meanwhile, it changes 'tso' on the TX devs
and 'gro' on the RX devs. Then it checks if any BIG TCP packets appears
on the RX devs with 'ip/ip6tables -m length ! --length 0:65535' for each
case.
Note that we also add tc action ct in link1 ingress to cover the ipv6
jumbo packets process in nf_ct_skb_network_trim() of nf_conntrack_ovs.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Florian Westphal <fw@strlen.de>
For IPv6 Jumbo packets, the ipv6_hdr(skb)->payload_len is always 0,
and its real payload_len ( > 65535) is saved in hbh exthdr. With 0
length for the jumbo packets, all data and exthdr will be trimmed
in nf_ct_skb_network_trim().
This patch is to call nf_ip6_check_hbh_len() to get real pkt_len
of the IPv6 packet, similar to br_validate_ipv6().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Rename br_nf_check_hbh_len() to nf_ip6_check_hbh_len() and move it
to netfilter utils, so that it can be used by other modules, like
ovs and tc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
br_nf_check_hbh_len() is a function to check the Hop-by-hop option
header, and shouldn't do pskb_trim_rcsum() there. This patch is to
pass pkt_len out to br_validate_ipv6() and do pskb_trim_rcsum()
after calling br_validate_ipv6() instead.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
In the while loop of br_nf_check_hbh_len(), similar to ip6_parse_tlv(),
before accessing 'nh[off + 1]', it should add a check 'len < 2'; and
before parsing IPV6_TLV_JUMBO, it should add a check 'optlen > len',
in case of overflows.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
When checking Hop-by-hop option header, if the option data is in
nonlinear area, it should do pskb_may_pull instead of discarding
the skb as a bad IPv6 packet.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Commit 0091bfc817 ("io_uring/af_unix: defer registered
files gc to io_uring release") added one bit to struct sk_buff.
This structure is critical for networking, and we try very hard
to not add bloat on it, unless absolutely required.
For instance, we can use a specific destructor as a wrapper
around unix_destruct_scm(), to identify skbs that unix_gc()
has to special case.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Pavel Begunkov <asml.silence@gmail.com>
Cc: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Cc: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nftables equivalent for ebtables -t broute.
Implement broute meta statement to set br_netfilter_broute flag
in skb to force a packet to be routed instead of being bridged.
Signed-off-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Florian Westphal <fw@strlen.de>
Steen Hegelund says:
====================
Add support for TC flower templates in Sparx5
This adds support for the TC template mechanism in the Sparx5 flower filter
implementation.
Templates are as such handled by the TC framework, but when a template is
created (using a chain id) there are by definition no filters on this
chain (an error will be returned if there are any).
If the templates chain id is one that is represented by a VCAP lookup, then
when the template is created, we know that it is safe to use the keys
provided in the template to change the keyset configuration for the (port,
lookup) combination, if this is needed to improve the match on the
template.
The original port keyset configuration is captured in the template state
information which is kept per port, so that when the template is deleted
the port keyset configuration can be restored to its previous setting.
The template also provides the protocol parameter which is the basic
information that is used to find out which port keyset configuration needs
to be changed.
The VCAPs and lookups are slightly different when it comes to which keys,
keysets and protocol are supported and used for selection, so in some
cases a bit of tweaking is needed to find a useful match. This is done by
e.g. removing a key that prevents the best matching keyset from being
selected.
The debugfs output that is provided for a port allows inspection of the
currently used keyset in each of the VCAPs lookups. So when a template has
been created the debugfs output allows you to verify if the keyset
configuration has been changed successfully.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for using the "template add" and "template destroy"
functionality to change the port keyset configuration.
If the VCAP lookup already contains rules, the port keyset is left
unchanged, as a change would make these rules unusable.
When the template is destroyed the port keyset configuration is restored.
The filters using the template chain will automatically be deleted by the
TC framework.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this its is now possible for clients (like TC) to change the port
keyset configuration in the Sparx5 VCAPs.
This is typically done per traffic class which is guided with the L3
protocol information.
Before the change the current keyset configuration is collected in a list
that is handed back to the client.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a list that is used to collect the templates that are active on a
port.
This allows the template creation to change the port configuration
and the template destruction to change it back.
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjorn Helgaas