Replace a comma between expression statements by a semicolon.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20201211085510.2928-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace a comma between expression statements by a semicolon.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20201211085553.2982-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During init, vbus_vsafe0v does not get updated till the first
connect as a sink. This causes TCPM to be stuck in SRC_ATTACH_WAIT
state while booting with a sink (For instance: a headset) connected.
[ 1.429168] Start toggling
[ 1.439907] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[ 1.445242] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected]
[ 53.358528] CC1: 0 -> 0, CC2: 0 -> 2 [state TOGGLING, polarity 0, connected]
[ 53.358564] state change TOGGLING -> SRC_ATTACH_WAIT [rev1 NONE_AMS]
Fix this by updating vbus_vsafe0v based on vbus_present status
on boot.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201211071911.2205197-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Auto discharge circuits kick in only when vbus decays and reaches
VBUS_SINK_DISCONNECT_THRESHOLD threshold. Enable bleed discharge to
discharge vbus to VBUS_SINK_DISCONNECT_THRESHOLD upon disconnect.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201211071145.2199997-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the Type C class for plug alternate mode devices which are being
registered by the Type C connector class. This ensures that udev events
get generated when the plug alt modes are registered.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20201210211653.879044-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCPM state machine needs 20-25ms to enter the ErrorRecovery state after
tPSSourceOn timer timeouts. Change the timer from max 480ms to 450ms to
ensure that the timer complies with the Spec. In order to keep the
flexibility for other usecases using tPSSourceOn, add another timer only
for PR_SWAP.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201210160521.3417426-5-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PD rev3.0 8.3.3.16.3.6 PE_PRS_SRC_SNK_Wait_Source_on State
The Policy Enging Shall transition to the ErrorRecovery state when the
PSSourceOnTimer times out ...
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201210160521.3417426-4-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PD 3.0 spec 8.3.3.2.3, A Get_Source_Cap message is sent
to a UUT that is in the PE_SRC_Ready state. After sending
a Source_Capabilities message, the UUT should then expect
a Request message in response. When one is not received,
the UUT should timeout to PE_SRC_Hard_Reset.
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Badhri Jagan Sridharan <badhri@google.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: pumahsu <pumahsu@google.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201210160521.3417426-3-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB4 specification chapter 3 indicates that cable data rates have to be
rounded for USB4 device to operate as USB4.
With that configure cable generation value to use rounded data rates for
USB4.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Link: https://lore.kernel.org/r/20201209042408.23079-2-utkarsh.h.patel@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change adds vbus_vsafe0v which when set, makes TCPM
query for VSAFE0V by assigning the tcpc.is_vbus_vsafe0v callback.
Also enables ALERT.ExtendedStatus which is triggered when
status of EXTENDED_STATUS.vSafe0V changes.
EXTENDED_STATUS.vSafe0V is set when vbus is at vSafe0V and
cleared otherwise.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201202040840.663578-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCPM at present lacks the notion of VSAFE0V. There
are three vbus threshold levels that are critical to track:
a. vSafe5V - VBUS “5 volts” as defined by the USB
PD specification.
b. vSinkDisconnect - Threshold used for transition from
Attached.SNK to Unattached.SNK.
c. vSafe0V - VBUS “0 volts” as defined by the USB
PD specification.
Tracking vSafe0V is crucial for entry into Try.SNK and
Attached.SRC and turning vbus back on by the source in
response to hard reset.
>From "4.5.2.2.8.2 Exiting from AttachWait.SRC State" section
in the Type-C spec:
"The port shall transition to Attached.SRC when VBUS is at
vSafe0V and the SRC.Rd state is detected on exactly one of
the CC1 or CC2 pins for at least tCCDebounce."
"A DRP that strongly prefers the Sink role may optionally
transition to Try.SNK instead of Attached.SRC when VBUS
is at vSafe0V and the SRC.Rd state is detected on exactly
one of the CC1 or CC2 pins for at least tCCDebounce."
>From "7.1.5 Response to Hard Resets" section in the PD spec:
"After establishing the vSafe0V voltage condition on VBUS,
the Source Shall wait tSrcRecover before re-applying VCONN
and restoring VBUS to vSafe5V."
vbus_present in the TCPM code tracks vSafe5V(vbus_present is true)
and vSinkDisconnect(vbus_present is false).
This change adds is_vbus_vsafe0v callback which when set makes
TCPM query for vSafe0V voltage level when needed.
Since not all TCPC controllers might have the capability
to report vSafe0V, TCPM assumes that vSafe0V is same as
vSinkDisconnect when is_vbus_vsafe0v callback is not set.
This allows TCPM to continue to support controllers which don't
have the support for reporting vSafe0V.
Introducing vSafe0V helps fix the failure reported at
"Step 15. CVS verifies PUT remains in AttachWait.SRC for 500ms"
of "TD 4.7.2 Try. SNK DRP Connect DRP Test" of
"Universal Serial Bus Type-C (USB Type-C) Functional Test
Specification Chapters 4 and 5". Here the compliance tester
intentionally maintains vbus at greater than vSafe0V and expects
the Product under test to stay in AttachWait.SRC till vbus drops
to vSafe0V.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201202040840.663578-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcpm_check_send_discover does not clear the send_discover flag
when any of the following conditions are not met.
1. data_role is TYPEC_HOST
2. link is pd_capable
Discovery indentity would anyways not be attempted during
the current session anymore when the above conditions are not
met. Hence clear the send_discover flag here to prevent
tcpm_enable_frs_work from rescheduling indefinetly.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201203031908.1491542-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nRetryCount was updated from 3 to 2 between PD2.0 and PD3.0 spec.
nRetryCount in "Table 6-34 Counter parameters" of the PD 2.0
spec is set to 3, whereas, nRetryCount in "Table 6-59 Counter
parameters" is set to 2.
Pass down negotiated rev in pd_transmit so that low level chip
drivers can update the retry count accordingly before attempting
packet transmission.
This helps in passing "TEST.PD.PORT.ALL.02" of the
"Power Delivery Merged" test suite which was initially failing
with "The UUT did not retransmit the message nReryCount times"
In fusb302 & tcpci drivers, by default the driver sets the retry
count to 3 (Default for PD 2.0). Update this to 2,
if the negotiated rev is PD 3.0.
In wcove, since the retry count is intentionally set to max, leaving
it as is.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201202031733.647808-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When Intel PMC Mux agent driver receives the response message from PMC, it
checks for the same response bits for all the mux states.
Corrected it by checking correct response message bits, Bit 8 & 9 for the
SAFE Mode and Alternate Modes and Bit 16 & 17 for the Connect and
Disconnect Modes.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Link: https://lore.kernel.org/r/20201203220813.16281-1-utkarsh.h.patel@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows downstream supplies and userspace to detect
whether external power is supplied.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Link: https://lore.kernel.org/r/2c8e81d9da9ff05b065f66edba915edd11f74065.1607166657.git.agx@sigxcpu.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is more in line with what tcpm does and will be needed
to avoid recursive dependency like
> drivers/power/supply/Kconfig:2:error: recursive dependency detected!
drivers/power/supply/Kconfig:2: symbol POWER_SUPPLY is selected by TYPEC_TPS6598X
drivers/usb/typec/Kconfig:64: symbol TYPEC_TPS6598X depends on REGMAP_I2C
drivers/base/regmap/Kconfig:19: symbol REGMAP_I2C is selected by CHARGER_ADP5061
drivers/power/supply/Kconfig:93: symbol CHARGER_ADP5061 depends on POWER_SUPPLY
For a resolution refer to Documentation/kbuild/kconfig-language.rst
subsection "Kconfig recursive dependency limitations"
when selecting POWER_SUPPLY.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Link: https://lore.kernel.org/r/6d11417c42d82caf66e08af160397959eb7d0d60.1607166657.git.agx@sigxcpu.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device tree property is named typec-power-opmode, not power-opmode.
Fixes: da0cb63100 ("usb: typec: add support for STUSB160x Type-C controller family")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201127131735.28280-1-amelie.delaunay@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB Power Delivery Specification defines a set of product
types for partners and cables. The product type can be read
from the ID Header VDO which is the first object in the
response to the Discover Identity command. This attribute
will display the product type of the partner. The cables
already have the attribute.
This sysfs attribute file is only created for the partners
and cables if the product type is really known in the
driver. Some interfaces do not give access to the Discover
Identity response from the partner or cable, but they may
still supply the product type separately in some cases.
When the product type of the partner or cable is detected,
uevent is also raised with PRODUCT_TYPE set to show the
actual product type (for example PRODUCT_TYPE=host).
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201126115735.50529-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These are never modified, so make them const to allow the compiler to
put them in read-only memory. Done with the help of coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20201125162500.37228-3-rikard.falkeborn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TD.4.7.3. Try SNK DRP Connect Try.SRC DRP fails. The compliance
tester mimics being a Try.SRC USB-C port.
The failure is due to TCPM exiting SNK_TRY_WAIT_DEBOUNCE_CHECK_VBUS
when VBUS is not present eventhough when SNK.Rp is seen. Exit to
SRC_TRYWAIT from SNK_TRY_WAIT_DEBOUNCE_CHECK_VBUS only when SNK.Rp
is not seen for PD_T_TRY_CC_DEBOUNCE.
>From the spec:
The port shall then transition to Attached.SNK when the SNK.Rp state
is detected on exactly one of the CC1 or CC2 pins for at least
tTryCCDebounce and VBUS is detected. Alternatively, the port shall
transition to TryWait.SRC if SNK.Rp state is not detected for
tTryCCDebounce.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201125014804.1596719-1-badhri@google.com
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During PR_SWAP sequence, when TCPM is waiting in PR_SWAP_SNK_SRC_SOURCE_ON
for the vbus source to ramp up, TCPM would prematurely exit
PR_SWAP_SNK_SRC_SOURCE_ON and transition to SNK_UNATTACHED state when a
vbus off notification is received. This should not be the case as vbus
can still be off while in PR_SWAP_SNK_SRC_SOURCE_ON and the vbus source
has PD_T_NEWSRC to ramp up.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201125020703.1604979-1-badhri@google.com
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A PD-capable device can return up to 3 Product Type VDOs as part of its
DiscoverIdentity Response (USB PD Spec, Rev 3.0, Version 2.0, Section
6.4.4.3.1). Add sysfs attributes to expose these to userspace.
Cc: Benson Leung <bleung@chromium.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20201125084911.1077462-2-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit to introduce the num_altmodes attribute for partner had an
error where one of the parameters was named differently in the comment
and the function signature. Fix the version in the comment to align with
what is in the function signature.
This fixes the following htmldocs warning:
drivers/usb/typec/class.c:632: warning: Excess function parameter 'num_alt_modes' description in 'typec_partner_set_num_altmodes'
Fixes: a0ccdc4a77 ("usb: typec: Add number of altmodes partner attr")
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20201120063523.4159877-1-pmalani@chromium.org
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a field to the typec_plug struct to record the number of available
altmodes as well as the corresponding sysfs attribute to expose this to
userspace.
This allows userspace to determine whether there are any
remaining alternate modes left to be registered by the kernel driver. It
can begin executing any policy state machine after all available
alternate modes have been registered with the connector class framework.
This value is set to "-1" initially, signifying that a valid number of
alternate modes haven't been set for the plug. The sysfs file remains
hidden as long as the attribute value is -1.
We re-use the partner attribute for number_of_alternate_modes since the
usage and name is similar, and update the corresponding *_show() command
to support both partner and plugs.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201116201150.2919178-4-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New smatch warnings:
drivers/usb/typec/tcpm/tcpci_maxim.c:324 max_tcpci_irq() error: uninitialized symbol 'irq_return'.
drivers/usb/typec/tcpm/tcpci_maxim.c:407 max_tcpci_probe() warn: passing zero to 'PTR_ERR'
The change fixes the above warnings by initializing irq_return
and replacing IS_ERR_OR_NULL with IS_ERR.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-11-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vImplement callbacks for enabling/disabling
POWER_CONTROL.AutoDischargeDisconnect.
Programs VBUS_SINK_DISCONNECT_THRESHOLD based on the
voltage requested as sink, mode of operation.
The programmed threshold is based on vSinkDisconnect and
vSinkDisconnectPD values.
Add auto_discharge_disconnect to tdata to allow TCPC chip
level drivers enable AutoDischargeDisconnect.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-9-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCPCI spec allows TCPC hardware to autonomously discharge the vbus
capacitance upon disconnect. The expectation is that the TCPM enables
AutoDischargeDisconnect while entering SNK/SRC_ATTACHED states. Hardware
then automously discharges vbus when the vbus falls below a certain
threshold i.e. VBUS_SINK_DISCONNECT_THRESHOLD.
Apart from enabling the vbus discharge circuit, AutoDischargeDisconnect
is also used a flag to move TCPCI based TCPC implementations into
Attached.Snk/Attached.Src state as mentioned in
Figure 4-15. TCPC State Diagram before a Connection of the
USB Type-C Port Controller Interface Specification.
In such TCPC implementations, setting AutoDischargeDisconnect would
prevent TCPC into entering "Connection_Invalid" state as well.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-8-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Occasionally, POWER_STATUS.sourcing_vbus takes a while to clear after
writing to MAX_BUCK_BOOST_OP register. This causes vbus to turn back
on while disconnecting the sink. Overcome this issue by writing into
MAX_BUCK_BOOST_OP during frs while sourcing vbu, instead of always
into the register whenever POWER_STATUS.sourcing_vbus is set.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-7-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During FRS hardware autonomously starts to source vbus. Provide
callback to perform chip specific operations.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-6-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During FRS hardware autonomously starts to source vbus. Provide
callback to perform chip specific operations.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-5-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New source's current capability is now defined as string based
device tree property through new-source-frs-typec-current.
Refactor tcpm code to parse new-source-frs-typec-current and
infer local port's new source current capability during frs.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201029063138.1429760-4-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a user-visible attribute for the number of alternate modes available
in a partner. This allows userspace to determine whether there are any
remaining alternate modes left to be registered by the kernel driver. It
can begin executing any policy state machine after all available
alternate modes have been registered with the connector class framework.
This value is set to "-1" initially, signifying that a valid number of
alternate modes haven't been set for the partner.
Also add a sysfs file which exposes this attribute. The file remains
hidden as long as the attribute value is -1.
Cc: Benson Leung <bleung@chromium.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201116201150.2919178-3-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thunderbolt cable generation bits received as a part of Thunderbolt 3 cable
discover mode VDO needs to be configured for Thunderbolt rounded and
non-rounded cable support in the Thunderbolt alternate mode.
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
--
Changes in v2:
- No change.
--
Link: https://lore.kernel.org/r/20201113202503.6559-4-utkarsh.h.patel@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix build errors when CONFIG_TYPEC_QCOM_PMIC=y and
CONFIG_USB_ROLE_SWITCH=m by limiting the former to =m when
USB_ROLE_SWITCH also =m.
powerpc64-linux-ld: drivers/usb/typec/qcom-pmic-typec.o: in function `.qcom_pmic_typec_remove':
qcom-pmic-typec.c:(.text+0x28): undefined reference to `.usb_role_switch_set_role'
powerpc64-linux-ld: qcom-pmic-typec.c:(.text+0x64): undefined reference to `.usb_role_switch_put'
powerpc64-linux-ld: drivers/usb/typec/qcom-pmic-typec.o: in function `.qcom_pmic_typec_check_connection':
qcom-pmic-typec.c:(.text+0x120): undefined reference to `.usb_role_switch_set_role'
powerpc64-linux-ld: drivers/usb/typec/qcom-pmic-typec.o: in function `.qcom_pmic_typec_probe':
qcom-pmic-typec.c:(.text+0x360): undefined reference to `.fwnode_usb_role_switch_get'
powerpc64-linux-ld: qcom-pmic-typec.c:(.text+0x4e4): undefined reference to `.usb_role_switch_put'
Fixes: 6c8cf36951 ("usb: typec: Add QCOM PMIC typec detection driver")
Cc: linux-usb@vger.kernel.org
Cc: Wesley Cheng <wcheng@codeaurora.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20201116040653.7943-1-rdunlap@infradead.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the ucsi power supply goes online/offline, and when the
power levels change, the power supply class needs to be
notified so it can inform the user space.
Fixes: 992a60ed0d ("usb: typec: ucsi: register with power_supply class")
Cc: stable@vger.kernel.org
Reported-and-tested-by: Vladimir Yerilov <openmindead@gmail.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201110120547.67922-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some/many PPMs are simply clearing the change bitfield when a
notification on a port is acknowledge. Unfortunately, doing so means
that any changes between the GET_CONNECTOR_STATUS and ACK_CC_CI commands
is simply lost.
Work around this by re-fetching the connector status afterwards. We can
then infer any changes that we see have happened but that may not be
respresented in the change bitfield.
We end up with the following actions:
1. UCSI_GET_CONNECTOR_STATUS, store result, update unprocessed_changes
2. UCSI_GET_CAM_SUPPORTED, discard result
3. ACK connector change
4. UCSI_GET_CONNECTOR_STATUS, store result
5. Infere lost changes by comparing UCSI_GET_CONNECTOR_STATUS results
6. If PPM reported a new change, then restart in order to ACK
7. Process everything as usual.
The worker is also changed to re-schedule itself if a new change
notification happened while it was running.
Doing this fixes quite commonly occurring issues where e.g. the UCSI
power supply would remain online even thought the ThunderBolt cable was
unplugged.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Link: https://lore.kernel.org/r/20201009144047.505957-3-benjamin@sipsolutions.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Normal commands may be reporting that a connector has changed. Always
call the usci_connector_change handler and let it take care of
scheduling the work when needed.
Doing this makes the ACPI code path identical to the CCG one.
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Link: https://lore.kernel.org/r/20201009144047.505957-2-benjamin@sipsolutions.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
chip->port_type and chip->pwr_opmode are enums and when GCC considers them
as unsigned, the conditions are never met.
This patch takes advantage of the ret variable and fixes the following
warnings:
drivers/usb/typec/stusb160x.c:548 stusb160x_get_fw_caps() warn: unsigned 'chip->port_type' is never less than zero.
drivers/usb/typec/stusb160x.c:570 stusb160x_get_fw_caps() warn: unsigned 'chip->pwr_opmode' is never less than zero.
Fixes: da0cb63100 ("usb: typec: add support for STUSB160x Type-C controller family")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201028163309.12878-1-amelie.delaunay@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When stusb160x driver is built as a module, no modalias information is
available, and it prevents the module to be loaded by udev.
Add MODULE_DEVICE_TABLE() to fix this issue.
Fixes: da0cb63100 ("usb: typec: add support for STUSB160x Type-C controller family")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20201028151703.31195-1-amelie.delaunay@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The typec_register_port() function doesn't return NULL, it returns error
pointers.
Fixes: da0cb63100 ("usb: typec: add support for STUSB160x Type-C controller family")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201023114017.GE18329@kadam
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current tcpm_detach() only reset hard_reset_count if port->attached
is true, this may cause this counter clear is missed if the CC
disconnect event is generated after tcpm_port_reset() is done
by other events, e.g. VBUS off comes first before CC disconect for
a power sink, in that case the first tcpm_detach() will only clear
port->attached flag but leave hard_reset_count there because
tcpm_port_is_disconnected() is still false, then later tcpm_detach()
by CC disconnect will directly return due to port->attached is cleared,
finally this will result tcpm will not try hard reset or error recovery
for later attach.
ChiYuan reported this issue on his platform with below tcpm trace:
After power sink session setup after hard reset 2 times, detach
from the power source and then attach:
[ 4848.046358] VBUS off
[ 4848.046384] state change SNK_READY -> SNK_UNATTACHED
[ 4848.050908] Setting voltage/current limit 0 mV 0 mA
[ 4848.050936] polarity 0
[ 4848.052593] Requesting mux state 0, usb-role 0, orientation 0
[ 4848.053222] Start toggling
[ 4848.086500] state change SNK_UNATTACHED -> TOGGLING
[ 4848.089983] CC1: 0 -> 0, CC2: 3 -> 3 [state TOGGLING, polarity 0, connected]
[ 4848.089993] state change TOGGLING -> SNK_ATTACH_WAIT
[ 4848.090031] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms
[ 4848.141162] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_ATTACH_WAIT, polarity 0, disconnected]
[ 4848.141170] state change SNK_ATTACH_WAIT -> SNK_ATTACH_WAIT
[ 4848.141184] pending state change SNK_ATTACH_WAIT -> SNK_UNATTACHED @20 ms
[ 4848.163156] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [delayed 20 ms]
[ 4848.163162] Start toggling
[ 4848.216918] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected]
[ 4848.216954] state change TOGGLING -> SNK_ATTACH_WAIT
[ 4848.217080] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms
[ 4848.231771] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_ATTACH_WAIT, polarity 0, disconnected]
[ 4848.231800] state change SNK_ATTACH_WAIT -> SNK_ATTACH_WAIT
[ 4848.231857] pending state change SNK_ATTACH_WAIT -> SNK_UNATTACHED @20 ms
[ 4848.256022] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [delayed20 ms]
[ 4848.256049] Start toggling
[ 4848.871148] VBUS on
[ 4848.885324] CC1: 0 -> 0, CC2: 0 -> 3 [state TOGGLING, polarity 0, connected]
[ 4848.885372] state change TOGGLING -> SNK_ATTACH_WAIT
[ 4848.885548] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @200 ms
[ 4849.088240] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed200 ms]
[ 4849.088284] state change SNK_DEBOUNCED -> SNK_ATTACHED
[ 4849.088291] polarity 1
[ 4849.088769] Requesting mux state 1, usb-role 2, orientation 2
[ 4849.088895] state change SNK_ATTACHED -> SNK_STARTUP
[ 4849.088907] state change SNK_STARTUP -> SNK_DISCOVERY
[ 4849.088915] Setting voltage/current limit 5000 mV 0 mA
[ 4849.088927] vbus=0 charge:=1
[ 4849.090505] state change SNK_DISCOVERY -> SNK_WAIT_CAPABILITIES
[ 4849.090828] pending state change SNK_WAIT_CAPABILITIES -> SNK_READY @240 ms
[ 4849.335878] state change SNK_WAIT_CAPABILITIES -> SNK_READY [delayed240 ms]
this patch fix this issue by clear hard_reset_count at any cases
of cc disconnect, í.e. don't check port->attached flag.
Fixes: 4b4e02c831 ("typec: tcpm: Move out of staging")
Cc: stable@vger.kernel.org
Reported-and-tested-by: ChiYuan Huang <cy_huang@richtek.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/1602500592-3817-1-git-send-email-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a common comment marked, instead, with kernel-doc
notation.
Also, some identifiers have different names between their
prototypes and the kernel-doc markup.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/0b964be3884def04fcd20ea5c12cb90d0014871c.1603469755.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These variables are enums but in this situation GCC will treat them as
unsigned so the conditions are never true.
Fixes: da0cb63100 ("usb: typec: add support for STUSB160x Type-C controller family")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20201023112412.GD282278@mwanda
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get
wrong, as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception of
the last "obviously correct" patch that updated a FALLTHROUGH comment
that got merged last weekend.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX4hAAg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfRACcCp48StLg4V7XcZ41eQYES/DVwxkAnjnZs+La
Y7F+o2p8DiuLLQamdEyB
=lHr1
-----END PGP SIGNATURE-----
Merge tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY/Thunderbolt driver updates from Greg KH:
"Here is the big set of USB, PHY, and Thunderbolt driver updates for
5.10-rc1.
Lots of tiny different things for these subsystems are in here,
including:
- phy driver updates
- thunderbolt / USB 4 updates and additions
- USB gadget driver updates
- xhci fixes and updates
- typec driver additions and updates
- api conversions to various drivers for core kernel api changes
- new USB control message functions to make it harder to get wrong,
as found by syzbot (took 2 tries to get it right)
- lots of tiny USB driver fixes and updates all over the place
All of these have been in linux-next for a while, with the exception
of the last "obviously correct" patch that updated a FALLTHROUGH
comment that got merged last weekend"
* tag 'usb-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (374 commits)
usb: musb: gadget: Use fallthrough pseudo-keyword
usb: typec: Add QCOM PMIC typec detection driver
USB: serial: option: add Cellient MPL200 card
usb: typec: tcpci_maxim: Add support for Sink FRS
usb: typec: tcpci: Implement callbacks for FRS
usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)
usb: typec: tcpci_maxim: Chip level TCPC driver
usb: typec: tcpci: Add set_vbus tcpci callback
usb: typec: tcpci: Add a getter method to retrieve tcpm_port reference
usbip: vhci_hcd: fix calling usb_hcd_giveback_urb() with irqs enabled
usb: cdc-acm: add quirk to blacklist ETAS ES58X devices
USB: serial: ftdi_sio: use cur_altsetting for consistency
USB: serial: option: Add Telit FT980-KS composition
USB: core: remove polling for /sys/kernel/debug/usb/devices
usb: typec: add support for STUSB160x Type-C controller family
usb: typec: add typec_find_pwr_opmode
usb: typec: hd3ss3220: Use OF graph API to get the connector fwnode
dt-bindings: usb: renesas,usb3-peri: Document HS and SS data bus
dt-bindings: usb: convert ti,hd3ss3220 bindings to json-schema
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
...
Zheng Yongjun