Add support for the BGR888_1X24 image format.
No existing media bus codes describe exactly the way data is transferred
on the CSI-2 bus. This is not a new issue, the CSI-2 YUV422 8-bit format
is described by MEDIA_BUS_FMT_UYVY8_1X16 which is an arbitrary
convention and not an exact match. Use the MEDIA_BUS_FMT_BGR888_1X24 to
follow the same convention, based on the order in which bits are
transmitted over the CSI-2 bus.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add RGB565_1X16 to the enumeration of supported image formats.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Bits 13 and 12 of the ISP_CONFIGn register configure the PIXEL_MODE
which specifies the sampling size, in pixel component units, on the
CSI-2 output data interface when data are transferred to memory.
The register description in the chip manual specifies that DUAL mode
should be used for YUV422 data.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Xavier Roumegue <xavier.roumegue@oss.nxp.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Rename the imx7-mipi-csis.c driver to remove the reference to i.MX7.
The driver is for an IP core found on i.MX7 and i.MX8 SoC, so do not
specify a SoC version number in the driver name.
Remove the references to the i.MX7 SoC in the driver symbols and expand
the driver's header with more information about the IP core the driver
controls.
Also rename the associated bindings documentation.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The imx7-mipi-csis driver is in a good state and can be destaged.
Move the imx7-mipi-csis.c driver to the newly created
drivers/media/platform/imx directory and plumb the related
options in Kconfig and in Makefile.
Signed-off-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rui Miguel Silva <rmfrfs@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The V4L2_EVENT_EOS event is a deprecated behavior,
the V4L2_BUF_FLAG_LAST buffer flag should be used instead.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Reviewed-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Do not use kernel-doc "/**" notation when the comment is not in
kernel-doc format. This fixes a sparse warning.
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the helper function time_is_{before,after}_jiffies() to improve
code readability.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the helper function time_is_{before,after}_jiffies() to improve
code readability.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the helper function time_is_{before,after}_jiffies() to improve
code readability.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the helper function time_is_{before,after}_jiffies() to improve
code readability.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use the helper function time_is_{before,after}_jiffies() to improve
code readability.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Some cx88 video cards may have transport stream status interrupts set
to 1 from cold start, causing errors like this:
cx88xx: cx88_print_irqbits: core:irq mpeg [0x100000] ts_err?*
cx8802: cx8802_mpeg_irq: mpeg:general errors: 0x00100000
According to CX2388x datasheet, the interrupt status register should be
cleared before enabling IRQs to stream video.
Fix it by clearing the Transport Stream Interrupt Status register.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Platform_driver probe functions aren't called with locks held
and thus don't need GFP_ATOMIC. Use GFP_KERNEL instead.
Problem found with Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Pci_driver probe functions aren't called with locks held
and thus don't need GFP_ATOMIC. Use GFP_KERNEL instead.
Problem found with Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Handle 0x0001, DMI type 1, 27 bytes
System Information
Manufacturer: ASUSTeK Computer Inc.
Product Name: A6JC
Version: 1.0
Serial Number: XXXXXXXXXXXXXXXXX
UUID: XXXXXXXXXXXXXXXXX
Wake-up Type: Power Switch
SKU Number: To Be Filled By O.E.M.
Family: To Be Filled By O.E.M.
Handle 0x0002, DMI type 2, 15 bytes
Base Board Information
Manufacturer: ASUSTeK Computer Inc.
Product Name: A6JC
Version: 1.0
Serial Number: XXXXXXXXXXXXXXXXX
Asset Tag: To Be Filled By O.E.M.
Features:
Board is a hosting board
Board is replaceable
Location In Chassis: To Be Filled By O.E.M.
Chassis Handle: 0x0003
Type: Motherboard
Contained Object Handles: 0
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: MEDIA ML <linux-media@vger.kernel.org>
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
When error occurs in parsing jpeg, the slot isn't acquired yet, it may
be the default value MXC_MAX_SLOTS.
If the driver access the slot using the incorrect slot number, it will
access array out of bounds.
The result is the driver will change num_domains, which follows
slot_data in struct mxc_jpeg_dev.
Then the driver won't detach the pm domain at rmmod, which will lead to
kernel panic when trying to insmod again.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Reviewed-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
With gstreamer 1.19.3 all attempts to capture video in YUV formats on
our Allwinner H3-based custom board with an ov5640 sensor result in
pipeline crashes with the following messages:
Device '/dev/video0' does not support 2:0:0:0 colorimetry
Additional debug info:
Device wants 2:0:0:0 colorimetry
Fix this by setting the correct colorspace in sun6i_video_try_fmt().
Signed-off-by: Mikhail Rudenko <mike.rudenko@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Call i2c_unregister_device(audio) on this error path.
Fixes: d3b2ccd9e3 ("[media] s2250: convert to the control framework")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The print function dev_err() is redundant because platform_get_irq()
already prints an error.
Eliminate the follow coccicheck warning:
./drivers/media/platform/imx-jpeg/mxc-jpeg.c:2025:3-10: line 2025 is
redundant because platform_get_irq() already prints an error
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fix following includecheck warning:
./drivers/media/platform/aspeed-video.c: linux/videodev2.h is included
more than once.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Variable idx is being assigned a value that is never read, it is being
re-assigned a new value in the following for-loop. The assignment is
redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Variable id is being assigned a value that is never read. The
assignment is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The variable plane_fmt is being initialized with a value that is never
read, it is being re-assigned a new value on each iteration of a for
loop. The initialization is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The variable n is being assigned a value that is never read, it is
being reassigned a different value a few statements later. The
assignment is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The only usage of go7007_snd_device_ops is to pass its address to
snd_device_new() which takes a pointer to const struct snd_device_ops.
Make it const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The static array lcr2vbi is read-only so it make sense to make
it const.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The commit 47677e51e2a4("[media] em28xx: Only deallocate struct
em28xx after finishing all extensions") adds kref_get to many init
functions (e.g., em28xx_audio_init). However, kref_init is called too
late in em28xx_usb_probe, since em28xx_init_dev before will invoke
those init functions and call kref_get function. Then refcount bug
occurs in my local syzkaller instance.
Fix it by moving kref_init before em28xx_init_dev. This issue occurs
not only in dev but also dev->dev_next.
Fixes: 47677e51e2 ("[media] em28xx: Only deallocate struct em28xx after finishing all extensions")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Make use of the struct_size() helper instead of an open-coded version,
in order to avoid any potential type mistakes or integer overflows that,
in the worst scenario, could lead to heap overflows.
Also, address the following sparse warnings:
drivers/media/usb/pwc/pwc-uncompress.c:44:44: warning: using sizeof on a flexible structure
Link: https://github.com/KSPP/linux/issues/174
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Let's v4l2 framework use a free /dev/videoX node for decode and encoder.
For the decoder call video_register_device() before register the media
controller device so the mapping between ins correctly done.
Since the registering sequence has changed rework exiting errors case too.
Fixes: 590577a4e5 ("[media] vcodec: mediatek: Add Mediatek V4L2 Video Decoder Driver")
Fixes: 4e855a6efa ("[media] vcodec: mediatek: Add Mediatek V4L2 Video Encoder Driver")
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Use of_device_get_match_data() to simplify the code.
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Current settings for video capture rgb-2-yuv is BT.601(studio swing),
but JFIF uses BT.601(full swing) to deocde. This mismatch will lead
to incorrect color. For example, input RGB value, (0, 0, 255), will
become (16, 16, 235) after jpg decoded.
Add an enum, aspeed_video_capture_format, to define VR008[7:6]
capture format and correct default settings for video capture to fix
the problem.
VR008[7:6] decides the data format for video capture as below:
* 00: CCIR601 studio swing compliant YUV format
* 01: CCIR601 full swing compliant YUV format
* 10: RGB format
* 11: Gray color mode
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Using stable-signal in resolution detection, and try detection again
if unstable.
VE_MODE_DETECT_EXTSRC_ADC: 1 if video source is from ADC output.
VE_MODE_DETECT_H_STABLE: 1 if horizontal signal detection is stable.
VE_MODE_DETECT_V_STABLE: 1 if vertical signal detection is stable.
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
VE_MODE_DT_HOR_TOLER: the tolerance in detecting for stable horizontal
signal.
VE_MODE_DT_VER_TOLER: the tolerance in detecting for stable vertical
signal.
VE_MODE_DT_HOR_STABLE: the minimum required count in detecting stable
HSYNC signal to set mode detection horizontal signal stable.
VE_MODE_DT_VER_STABLE: the minimum required count in detecting stable
VSYNC signal to set mode detection vertical signal stable.
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add comments to describe video-stat and 'struct aspeed_video'.
Add macro, ASPEED_VIDEO_V4L2_MIN_BUF_REQ, to describe the buffers
needed.
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: drop docbook tags, not needed]
When Gen3 support was first added to this R-Car VIN and CSI-2 driver the
routing was centred around the CHSEL register which multiplexes the
different parallel buses that sit between the CSI-2 receivers source
side and the VIN dma engines. This was a bad design as the multiplexing
do allow for only a few combinations and do not play nice with many
video streams in the system.
For example it's only possible for CSI-2 Virtual Channels 0 and 1 of any
given CSI-2 receiver to be used together with the scaler.
Later datasheets have expanded the documentation and it is now possible
to improve on this design by allowing any Virtual Channel to be routed
to any R-Car VIN instance, provided that there exists a parallel bus
between them. This increases the flexibility as all Virtual Channels can
now be used together with the scaler for example.
The redesign is not however perfect. While the new design allows for
many more routes, two constrains limit a small portion of routes that
was possible in the old design but are no more.
- It is no longer possible to route the same CSI-2 and VC to more then
one VIN at a time. This was theoretically possible before if the
specific SoC allowed for the same CSI-2 and VC to be routed to two
different VIN capture groups.
- It is no longer possible to simultaneously mix links from two CSI-2 IP
blocks to the same VIN capture group.
For example if VIN2 is capturing from CSI40 then VIN{0,1,3} must also
capture from CSI40. While VIN{4,5,6,7} is still free to capture from
any other CSI-2 IP in the system. Once all VIN{0,1,2,3} links to CSI40
are disabled that VIN capture group is free again to capture from any
other CSI-2 IP it is connected to.
At the core of the redesign is greater cooperator of the R-Car VIN and
CSI-2 drivers in configuring the routing. The VIN driver is after this
change only responsible to configure the full VIN capture groups
parallel buses to be to a particular CSI-2 IP. While the configuration
of which CSI-2 Virtual Channel is outputted on which of the R-Car CSI-2
IP output ports is handled by the CSI-2 driver.
Before this change the CSI-2 Virtual Channel to output port was static
in the CSI-2 driver and the different links only manipulated the VIN
capture groups CHSEL register. With this change both the CHSEl register
and the CSI-2 routing VCDT registers are modified for greater
flexibility.
This change touches both the R-Car VIN and R-Car CSI-2 drivers in the
same commit as both drivers cooperate closely and one change without the
other would more or less break video capture.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: fix two trivial checkpatch whitespace issues]
In preparation of creating more links to allow for full Virtual Channel
routing within the CSI-2 block break out the link creation logic to a
helper function as the logic will grow in future work.
There is no functional change.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The code has grown organically and a lot of checks are performed for
the CSI-2 use-case even if the link notify is for a subdevice connected
to the parallel interface.
Before reworking the CSI-2 routing logic split the CSI-2 and parallel
link notify code in two separate blocks to make it clearer. There is no
functional change.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Replace the driver-specific definitions of MIPI CSI-2 data types with
macros from mipi-csi2.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
VSP hardware could be used (e.g. by the bootloader) before driver load,
and some interrupts could be left in enabled and pending state. In this
case, setting up VSP interrupt handler without masking interrupts before
causes interrupt handler to be immediately called (and crash due to null
vsp->info dereference).
Fix that by explicitly masking all interrupts before setting the interrupt
handler. To do so, have to set the interrupt handler later, after hw
revision is already detected and number of interrupts to mask gets
known.
Based on patch by Koji Matsuoka <koji.matsuoka.xm@renesas.com> included
in the Renesas BSP kernel.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Adds the requisite device id to support detection of the Apple FaceTime
HD webcam exposed over the T2 BCE VHCI interface.
Tested-by: Aun-Ali Zaidi <admin@kodeit.net>
Signed-off-by: Paul Pawlowski <paul@mrarm.io>
Signed-off-by: Aun-Ali Zaidi <admin@kodeit.net>
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In cal_ctx_v4l2_init_formats(), devm_kzalloc() is assigned to
ctx->active_fmt and there is a dereference of it after that, which could
lead to NULL pointer dereference on failure of devm_kzalloc().
Fix this bug by adding a NULL check of ctx->active_fmt.
This bug was found by a static analyzer.
Builds with 'make allyesconfig' show no new warnings, and our static
analyzer no longer warns about this code.
Fixes: 7168155002 ("media: ti-vpe: cal: Move format handling to cal.c and expose helpers")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This error path needs to drop the mutex to avoid a deadlock.
Fixes: 7be91e02ed ("media: i2c: Add ov08d10 camera sensor driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
MWB gain register are used to set gain for each mwb channel mannually.
However, it will involve some artifacts at low light environment as gain
cannot be applied to each channel synchronously. Update the driver to use
group write for digital gain to make the sure RGB digital gain be applied
together at frame boundary.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields. Wrap the target region
in struct_group(). This additionally fixes a theoretical misalignment
of the copy (since the size of "buf" changes between 64-bit and 32-bit,
but this is likely never built for 64-bit).
FWIW, I think this code is totally broken on 64-bit (which appears to
not be a "real" build configuration): it would either always fail (with
an uninitialized data->buf_size) or would cause corruption in userspace
due to the copy_to_user() in the call path against an uninitialized
data->buf value:
omap3isp_stat_request_statistics_time32(...)
struct omap3isp_stat_data data64;
...
omap3isp_stat_request_statistics(stat, &data64);
int omap3isp_stat_request_statistics(struct ispstat *stat,
struct omap3isp_stat_data *data)
...
buf = isp_stat_buf_get(stat, data);
static struct ispstat_buffer *isp_stat_buf_get(struct ispstat *stat,
struct omap3isp_stat_data *data)
...
if (buf->buf_size > data->buf_size) {
...
return ERR_PTR(-EINVAL);
}
...
rval = copy_to_user(data->buf,
buf->virt_addr,
buf->buf_size);
Regardless, additionally initialize data64 to be zero-filled to avoid
undefined behavior.
Link: https://lore.kernel.org/lkml/20211215220505.GB21862@embeddedor
Cc: Arnd Bergmann <arnd@arndb.de>
Fixes: 378e3f81cb ("media: omap3isp: support 64-bit version of omap3isp_stat_data")
Cc: stable@vger.kernel.org
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
MIPI CSI-2 continuous and non-continuous clock modes are mutually
exclusive. Drop the V4L2_MBUS_CSI2_CONTINUOUS_CLOCK flag and use
V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The V4L2_MBUS_CSI2_CHANNEL_* flags are a legacy API. Only
V4L2_MBUS_CSI2_CHANNEL_0 is used, set in a single driver, and never
read. Drop those flags. Virtual channel information should be conveyed
through frame descriptors instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The media bus configuration is specified through a set of flags, some of
which being mutually exclusive. This doesn't scale to express more
complex configurations. Improve the API by replacing the single flags
field in v4l2_mbus_config by a union of v4l2_mbus_config_* structures.
The flags themselves are still used in those structures, so they are
kept here. Drivers are however updated to use structure fields instead
of flags when already possible.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
As part of removing mbus config flags, remove VC flag use in the
microchip-csi2dc driver. The support can be reintroduced later on as part
of the streams patches.
[mchehab: patch accepted by Eugen: https://lore.kernel.org/linux-media/c0676a4e-803f-9f1c-542b-4b007705ef3d@microchip.com/, so add an accepted-by tag]
Accepted-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
QCOM ISPs do not support having a programmable CSI Clock Lane number.
In order to accurately reflect this, the different CSIPHY HW versions
need to have their own register layer for computing lane masks.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Calling hdmi_infoframe_unpack() with static sizeof(buffer) skips all
the size checking done later in hdmi_infoframe_unpack(). A better
value is the amount of data read into buffer.
Fixes: 480b8b3e42 ("video/hdmi: Pass buffer size to infoframe unpack functions")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The vimc driver is used for testing purpose, and some test use cases
involve sharing buffers with a consumer device. Consumers often require
DMA contiguous memory, which vimc doesn't currently support. This leads
in the best case to usage of bounce buffers, which is very slow, and in
the worst case in a complete failure.
Add support for the dma-contig allocator in vimc to support those use
cases properly. The allocator is selected through a new "allocator"
module parameter, which defaults to vmalloc.
[hverkuil: add missing 'select VIDEOBUF2_DMA_CONFIG' to Kconfig]
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The CLIP, SRC & DST registers are coded to take the pixel/line start & end,
starting from 0. Thus the end should be the width/height minus 1.
It can be an issue with clipping and rotation, where it will add spurious
lines from uninitialized or unwanted data with a shift in the result.
Fixes: 59a635327c ("media: meson: Add M2M driver for the Amlogic GE2D Accelerator Unit")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Tag all the coded formats where the s5p_mfc decoder supports dynamic
resolution switching or has a bytestream parser.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename struct dma_buf_map to struct iosys_map and corresponding APIs.
Over time dma-buf-map grew up to more functionality than the one used by
dma-buf: in fact it's just a shim layer to abstract system memory, that
can be accessed via regular load and store, from IO memory that needs to
be acessed via arch helpers.
The idea is to extend this API so it can fulfill other needs, internal
to a single driver. Example: in the i915 driver it's desired to share
the implementation for integrated graphics, which uses mostly system
memory, with discrete graphics, which may need to access IO memory.
The conversion was mostly done with the following semantic patch:
@r1@
@@
- struct dma_buf_map
+ struct iosys_map
@r2@
@@
(
- DMA_BUF_MAP_INIT_VADDR
+ IOSYS_MAP_INIT_VADDR
|
- dma_buf_map_set_vaddr
+ iosys_map_set_vaddr
|
- dma_buf_map_set_vaddr_iomem
+ iosys_map_set_vaddr_iomem
|
- dma_buf_map_is_equal
+ iosys_map_is_equal
|
- dma_buf_map_is_null
+ iosys_map_is_null
|
- dma_buf_map_is_set
+ iosys_map_is_set
|
- dma_buf_map_clear
+ iosys_map_clear
|
- dma_buf_map_memcpy_to
+ iosys_map_memcpy_to
|
- dma_buf_map_incr
+ iosys_map_incr
)
@@
@@
- #include <linux/dma-buf-map.h>
+ #include <linux/iosys-map.h>
Then some files had their includes adjusted and some comments were
update to remove mentions to dma-buf-map.
Since this is not specific to dma-buf anymore, move the documentation to
the "Bus-Independent Device Accesses" section.
v2:
- Squash patches
v3:
- Fix wrong removal of dma-buf.h from MAINTAINERS
- Move documentation from dma-buf.rst to device-io.rst
v4:
- Change documentation title and level
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204170541.829227-1-lucas.demarchi@intel.com
If the driver reports that the hardware had an overflow, report this to
userspace. It would be nice to know when this happens, and not just get
a long space.
This change has been tested with lircd, ir-ctl, and ir-keytable.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver report a reset event when the hardware reports and overflow.
There is no reason to have a generic "reset" event.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Correct timing's fp/sync/bp value based on the information below.
It should be noticed that the calculation formula should be changed
per sync polarity.
The sequence of signal: sync - backporch - video data - frontporch
The following registers start counting from sync's rising edge:
1. VR090: frame edge's left and right
2. VR094: frame edge's top and bottom
3. VR09C: counting from sync's rising edge to falling edge
[Vertical timing]
+--+ +-------------------+ +--+
| | | v i d e o | | |
+--+ +-----+ +-----+ +---+
vsync+--+
frame_top+--------+
frame_bottom+----------------------------+
+-------------------+
| v i d e o |
+--+ +-----+ +-----+ +---+
| | | |
+--+ +--+
vsync+-------------------------------+
frame_top+-----+
frame_bottom+-------------------------+
[Horizontal timing]
+--+ +-------------------+ +--+
| | | v i d e o | | |
+--+ +-----+ +-----+ +---+
hsync+--+
frame_left+--------+
frame_right+----------------------------+
+-------------------+
| v i d e o |
+--+ +-----+ +-----+ +---+
| | | |
+--+ +--+
hsync+-------------------------------+
frame_left+-----+
frame_right+-------------------------+
Ex. 1920x1200@60 whose vsync polarity is negative
VR098: c4d3efff, VR09C: 04cc001f
v-total = 0x4D3 (VR098[27:16]) = 1235
v-sync = 0x4CC (VR09C[27:16]) = 1228
[hverkuil: drop unused variable mds]
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the bitfield macro FIELD_GET, and GENMASK to do the shift and mask in
one go for reg values.
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Previous reg-field, 0x98[11:0], stands for the period of the detected
hsync signal.
Use the correct reg, 0xa0, to get h-total in pixels.
Fixes: d2b4387f3b ("media: platform: Add Aspeed Video Engine driver")
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In ast2500, engine will stop occasionally for 1360x768.
This is a bug which has been addressed, but the workaround is specific
for 1680 only. Here we make it more complete.
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The new messages are listed as below:
1. jpeg header and capture buffer information
2. information for each irq
3. current capture mode, sync or direct-fetch
4. time consumed for each frame
5. input timing changed information
[hverkuil: use %pad for dma_addr_t to avoid compiler warnings]
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The debug log level, 0~3, is controlled by module_param, debug.
The higher the value, the more the information.
0: off
1: info
2: debug
3: register operations
Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Allow the dw9714 to control a regulator and adjust suspend() and resume()
to support both runtime and system pm.
Signed-off-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The module identifying will try to get the sub device data which
will be ready after sub device initialisation, so if try to use the
subdev data to deference the client will cause NULL pointer
dereference, this patch move the module identification after
v4l2_i2c_subdev_init() to fix this issue, it also fixes duplicate
module idendification.
Fixes: ada2c4f54d ("media: ov2740: support device probe in non-zero ACPI D state")
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The MAX9286 has sink pads, so it should implement .link_validate(). Do
so.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
drivers/media/i2c/ov5693.c:989:46-51: WARNING: conversion to bool not needed here
drivers/media/i2c/ov5693.c:991:46-51: WARNING: conversion to bool not needed here
Remove unneeded conversion to bool
Semantic patch information:
Relational and logical operators evaluate to bool,
explicit conversion is overly verbose and unneeded.
Generated by: scripts/coccinelle/misc/boolconv.cocci
[Sakari Ailus: Improved subject]
CC: Daniel Scally <djrscally@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a v4l2 sub-device driver for the OmniVision ov08d10 image sensor.
This camera sensor is using the i2c bus for control and the
csi-2 bus for data.
The following features are supported:
- manual exposure and analog/digital gain control
- vblank/hblank control
- test pattern
- image vertical flip and horizontal mirror control
- supported resolution:
- 3280x2460 at 30 FPS
- 3264x2448 at 30 FPS
- 1632x1224 at 30 FPS
- supported bayer order output:
- SGRBG10 as default
- SBGGR10 at flip mode
- SRGGB10 at mirror mode
- SGBRG10 at flip + mirror mode
Signed-off-by: Jimmy Su <jimmy.su@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a V4L2 sub-device driver for Hynix Hi-847 image sensor.
This is a camera sensor using the I2C bus for control and the
CSI-2 bus for data.
This driver supports following features:
- manual exposure and analog/digital gain control support
- vblank/hblank control support
- test pattern support
- media controller support
- runtime PM support
- vflip/hflip control support
- keep SGRBG10 Bayer order output
- support following resolutions:
+ 3264x2448 at 30FPS
+ 1632x1224 at 60FPS
[Sakari Ailus: Wrapped a few long lines.]
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Don't pack the driver specific struct containing control pointers. This
lead to potential alignment issues when working with the pointers.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: e43ccb0a04 ("media: i2c: Add support for the OV5648 image sensor")
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Pointers V4L2 pixelformat and dataformat fields in a few packed structs
are directly passed to printk family of functions. This could result in an
unaligned access albeit no such possibility appears to exist at the
moment i.e. this clang warning appears to be a false positive.
Address the warning by copying the pixelformat or dataformat value to a
local variable first.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: e927e1e0f0 ("v4l: ioctl: Use %p4cc printk modifier to print FourCC codes")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
According to v4l2-compliance utility, a video device which supports
V4L2_CAP_TIMEPERFRAME via .vidioc_s_parm() operation should also
support .vidioc_enum_frameintervals(). If the former is implemented
via a call to v4l2_s_parm_cap() which in turn calls a subdevice
.s_frame_interval() pad operation, the video device may want to
implement the latter by passing frame interval enumeration requests to
the subdevice .enum_frame_intervals() video operation. If that
operation is not supported by the subdevice and failure is returned by
the video device, the compliance test issues a warning.
Implement the missing pad operation. Enumerate frame intervals
possible to be set via pixel clock adjustment, as implemented by
.s_frame_interval(), but not exceeding a reasonable maximum of 1
second.
[Sakari Ailus: Rebased on mbus config pad op patches]
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
According to subdevice interface specification found in V4L2 API
documentation, set format pad operations should not affect image
geometry set in preceding image processing steps. Unfortunately, that
requirement is not respected by the driver implementation of set format
as it was not the case when that code was still implementing a pair of
now obsolete .s_mbus_fmt() / .try_mbus_fmt() video operations before
they have been merged and reused as an implementation of .set_fmt() pad
operation by commit 717fd5b490 ("[media] v4l2: replace try_mbus_fmt
by set_fmt").
Exclude non-compliant crop rectangle adjustments from set format try,
as well as a call to .set_selection() from set format active processing
path, so only frame scaling is applied as needed and crop rectangle is
no longer modified.
[Sakari Ailus: Rebase on subdev state patches]
Fixes: 717fd5b490 ("[media] v4l2: replace try_mbus_fmt by set_fmt")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Try requests are now only supported by format processing pad operations
implemented by the driver. The driver selection API operations
currently respond to them with -EINVAL. While that is correct, it
constraints video device drivers to not use subdevice cropping at all
while processing user requested active frame size, otherwise their set
try format results might differ from active. As a consequence, we
can't fix set format pad operation as not to touch crop rectangle since
that would affect users not being able to set arbitrary frame sizes.
Moreover, without a working set try selection support we are not able
to use pad config crop rectangle as a reference while processing set
try format requests.
Implement missing try selection support. Moreover, as it will be now
possible to maintain the pad config crop rectangle via selection API,
start using it instead of the active one as a reference while
processing set try format requests.
is_unscaled_ok() helper, now also called from set selection operation,
has been just moved up in the source file to avoid a prototype, with no
functional changes.
[Sakari Ailus: Rebase on subdev state patches]
Fixes: 717fd5b490 ("[media] v4l2: replace try_mbus_fmt by set_fmt")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
According to subdevice interface specification found in V4L2 API
documentation, set format pad operations should not affect image
geometry set in preceding image processing steps. Unfortunately, that
requirement is not respected by the driver implementation of set format
as it was not the case when that code was still implementing a pair of
now obsolete .s_mbus_fmt() / .try_mbus_fmt() video operations before
they have been merged and reused as an implementation of .set_fmt() pad
operation by commit 717fd5b490 ("[media] v4l2: replace try_mbus_fmt
by set_fmt").
In case of set format active processing path the issue can be fixed
easily by excluding a call to set active selection from that path. That
will effectively limit frame size processing to optimal frame scaling
against active crop rectangle without touching it. Users can just call
set active selection themselves to obtain desired frame size. However,
set format try processing path needs more work.
First of all, the driver should be extended with set try selection
support. Lack of it constraints video device drivers to not use
subdevice cropping at all while processing user requested active frame
size, otherwise their set try format results might differ from active.
Next, set format try processing path should use pad config crop
rectangle as a reference, not the active one as it does now. That
issue can be resolved easily as soon as set try selection support is
added to the driver so pad config crop rectangle can be maintained by
users via selection API.
Last, set format try processing path should give the same results as
active in respect to active vs. pad config crop rectangle geometry.
Both rectangles should be either not touched by set format (that's what
we are going to achieve) or modified the same way, otherwise users
won't be able to obtain equal results from both paths while iterating
through set format and set selection operations in order to obtain
desired frame size.
We can't begin with modifying set format pad operation as not to touch
crop rectangle since that depends on availability of set try selection
for symmetry. Neither can we begin with adding set try selection since
that in turn depends on equal handling of active and pad config crop
rectangles by set format. We can either implement all required
modifications in a single patch, or begin with fixing current set
format try processing path to appropriately handle pad config crop
rectangle. This patch implements the latter approach as believed to
be more readable.
Move crop rectangle adjustments code from a helper (the former
implementation of .s_fmt(), now called from set format active
processing path) to the body of set format pad operation function
where it can be also used for processing try requests for symmetry with
active ones. As the helper no longer processes frame geometry, only
frame format and half scaling, simplify its API accordingly and update
its users.
Moreover, extract code that applies crop rectangle hardware limits
(now a part of .set_selection() operation which is called from set
format active processing path) to a new helper and call that helper
from set format try processing path as well for symmetry with active.
[Sakari Ailus: Rebase on subdev state patches]
Fixes: 717fd5b490 ("[media] v4l2: replace try_mbus_fmt by set_fmt")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
To prepare for usage of the v4l2_fwnode_bus_* data structures to
describe bus configuration in the subdev .get_mbus_config() operation,
rename the structures with a v4l2_mbus_config_ prefix instead of
v4l2_fwnode_bus_, and move them to v4l2_mediabus.h.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The .set_mbus_config() operation is deprecated, and nothing in the
kernel uses it. Drop it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The subdev .set_mbus_config() operation is deprecated. No code in the
kernel calls it, so drop its implementation from the ov6650 driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The subdev .set_mbus_config() operation is deprecated and will be
dropped. Drop its usage from the pxa_camera driver, querying the sensor
bus configuration instead of setting it. Only the ov6650 driver supports
the operation, any platform that experiences issues with this change
should update the ov6650 configuration to match what pxa_camera
supports.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
MediaTek IOMMU has already added the device_link between the consumer
and smi-larb device. If the vcodec devices call the pm_runtime_get_sync,
the smi-larb's pm_runtime_get_sync also be called automatically.
CC: Irui Wang <irui.wang@mediatek.com>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Tiffany Lin <tiffany.lin@mediatek.com>
Reviewed-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
MediaTek IOMMU has already added the device_link between the consumer
and smi-larb device. If the mdp device calls the pm_runtime_get_sync,
the smi-larb's pm_runtime_get_sync also be called automatically.
CC: Minghsiu Tsai <minghsiu.tsai@mediatek.com>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Houlong Wei <houlong.wei@mediatek.com>
Reviewed-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
MediaTek IOMMU has already added device_link between the consumer
and smi-larb device. If the jpg device calls the pm_runtime_get_sync,
the smi-larb's pm_runtime_get_sync also be called automatically.
After removing the larb_get operations, then mtk_jpeg_clk_init is
also unnecessary. Remove it too.
CC: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Rick Chang <rick.chang@mediatek.com>
Reviewed-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de> # BPI-R2/MT7623
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
No concurrent access is possible when a bitmap is local to a function.
So prefer the non-atomic '__[set|clear]_bit()' functions to save a few
cycles.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If the application queues an NV12M jpeg as output buffer, but then
queues a single planar capture buffer, the kernel will crash with
"Unable to handle kernel NULL pointer dereference" in mxc_jpeg_addrs,
prevent this by finishing the job with error.
Signed-off-by: Mirela Rabulea <mirela.rabulea@oss.nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The reference taken by 'of_find_device_by_node()' must be released when
not needed anymore.
Add the corresponding 'put_device()' in the error handling path.
Fixes: e7f3c54810 ("[media] coda: use VDOA for un-tiling custom macroblock format")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
mtk_vpu_probe() calls platform_get_resource(pdev, IORESOURCE_IRQ, ..)
to check if IRQ resource exists and later calls
platform_get_irq(pdev, ..) to get the actual IRQ.
This patch drops an unnecessary call to platform_get_resource() and
checks the return value of platform_get_irq(pdev, ..) to make sure the
IRQ line is valid.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
platform_get_resource_byname(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_byname().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The 'maxim,gpio-poc' property is used when the remote camera
power-over-coax is controlled by one of the MAX9286 gpio lines,
to instruct the driver about which line to use and what the line
polarity is.
Add to the max9286 driver support for parsing the newly introduced
property and use it if available in place of the usual supply, as it is
not possible to establish one as consumer of the max9286 gpio
controller.
If the new property is present, no gpio controller is registered and
'poc-supply' is ignored.
In order to maximize code re-use, break out the max9286 gpio handling
function so that they can be used by the gpio controller through the
gpio-consumer API, or directly by the driver code.
Wrap the power up and power down routines to their own function to
be able to use either the gpio line directly or the supply. This will
make it easier to control the remote camera power at run time.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Re-write without unnecessary shifts.
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This IR receiver has two limitations:
1) Any IR pulse or space longer than 12ms will be truncated to 12ms
2) Any pulses/spaces after the first 68 are lost
ir_raw_event_reset() won't help here. If the IR cannot be decoded, any
decoder should reset itself, and if it does not, this is a bug in the
decoder.
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ir receiver generates an interrupt with the IR data, once a space of
at least ok_count is has been seen. Currently this is about 110ms; when
holding down a button on a nec remote, no such space is seen until the
button is released. This means nothing happens until you release the
button.
The sample rate is fixed at 46us, so the maximum space that can be
encoded is about 12ms. So, the set ok_count above that at 23ms.
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When a driver reports a timeout, no more IR activity will be reported
until the next pulse. A space is inserted between the timeout and the
next pulse, based on ktime.
The timeout reports already a duration, so this duration should not be
added to the gap. Otherwise there is no change to the functionality.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fix leak in error path.
Signed-off-by: Peiwei Hu <jlu.hpw@foxmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There are only two lines in mtk_vcodec_release_enc_pm, using
pm_runtime_disable and put_device instead directly.
Move pm_runtime_enable outside mtk_vcodec_release_enc_pm to symmetry with
pm_runtime_disable, after that, rename mtk_vcodec_init_enc_pm to *_clk
since it only has clock operations now.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There are only two lines in mtk_vcodec_release_dec_pm, using
pm_runtime_disable and put_device instead directly.
Move pm_runtime_enable outside mtk_vcodec_init_dec_pm to symmetry with
pm_runtime_disable, after that, rename mtk_vcodec_init_dec_pm to *_clk
since it only has clock operations now.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There is just one core thread, in order to separate different
hardware, using codec type to separeate it in scp driver.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add core dec and dec end ipi msg:
AP_IPIMSG_DEC_CORE/AP_IPIMSG_DEC_CORE_END.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the dma_set_mask_and_coherent helper to set vdec
DMA bit mask to support 34bits iova space(16GB) that
the mt8192 iommu HW support.
Whole the iova range separate to 0~4G/4G~8G/8G~12G/12G~16G,
regarding which iova range VDEC actually locate, it
depends on the dma-ranges property of vdec dtsi node.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add work queue to process core hardware information.
First, get lat_buf from message queue, then call core
hardware of each codec(H264/VP9/AV1) to decode, finally
puts lat_buf back to the message.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Steve Cho <stevecho@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
For add new hardware, not only need to lock lat hardware, also
need to lock core hardware in case of different instance start
to decoder at the same time.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Generalizes power and clock on/off interfaces to support different
hardware.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
For lat and core architecture, lat thread will send message to core
thread when lat decode done. Core hardware will use the message
from lat to decode, then free message to lat thread when decode done.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Adds irq interface for multi hardware.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Separates different architecture for hardware: pure_sin_core
and lat_sin_core. MT8183 is pure single core. Uses .hw_arch to
distinguish.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There are more than two hardwares for decoder: LAT0, LAT1 and CORE. In
order to manage these hardwares, register each hardware as independent
platform device for the larbs are different.
Each hardware module controls its own information which includes
interrupt/power/clocks/registers.
Calling of_platform_populate in parent device, and use subdev_bitmap to
record whether the hardwares are registered.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Steve Cho <stevecho@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
When mtk vcodec decoder is build as a module, we need to export
mtk-vcodec-dec pm functions to make them visible by the other components.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Using the needed params for pm init/release function and remove unused
param mtkdev in 'struct mtk_vcodec_pm'.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Steve Cho <stevecho@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Vdec and venc can use the same function to wake up interrupt event.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Steve Cho <stevecho@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Different platforms may have different numbers of register bases. Gets the
numbers of register bases from dts (sizeof(u32) * 4 bytes for each).
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ISC can dump the 8 bit and 10 bit raw bayer formats directly to
the memory.
Thus, add them to the supported output format list.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Fix the mbus code for UYVY input format type to the right color rotation.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
White balance computed gains can overflow above the 13 bits hardware
coefficient that can be used, in some specific scenarios like a subexposure
from the sensor when the image is mostly black.
In this case the computed gain has to be clamped to the maximum value
allowed by the hardware.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add debug messages that make it easier to debug white balance algorithm.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The bytesperline field of the pixfmt should be only for the first plane
in case of planar formats like YUV420 or YUV422.
The bytesperline is used by the driver to compute the framesize.
We have to report a different bpp (bytes per pixel) to v4l2 in bytesperline
than the actual bpp.
For example for YUV420, the real bpp is 12, but the first plane has only
8 bpp. Thus we report a bytesperline 8*width instead of 12*width.
However, for real framezise we have to compute 12*width*height.
Hence added a new variable to hold this information and to correctly
compute the frame size.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ISC supports a full broad range of frame sizes.
Until now, the subdevice was queried for possible frame sizes and these
were reported to the user space.
However, the ISC should not care about which frame sizes the subdev
supports, as long as this frame size is supported.
Thus, report a continuous range from smallest frame size up to the max
resolution.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
VIDIOC_ENUM_FRAMEINTERVALS is not recommended for a top video driver.
The frame rate is defined by the sensor subdevice, thus it can be queried
directly by anyone interested in the frame intervals.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ispck is not used for sama7g5 variant of the ISC.
Calls to ispck have to be removed also from module insert/removal.
Fixes: d7f26849ed ("media: atmel: fix the ispck initialization")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
To have consistency with future media controller development,
replace the video device name with KBUILD_MODNAME.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The atmel-isc-base is getting crowded. Split the clock functions into
atmel-isc-clk.c.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Microchip CSI2DC (CSI2 Demultiplexer Controller) is a misc bridge device
that converts a byte stream in IDI Synopsys format (coming from a CSI2HOST)
to a pixel stream that can be captured by a sensor controller.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Prior to submitting a transfer to the DMA, the client should first check
the capabilities of the DMA channel in term of maximum of each segment.
This is given by the max_sg_burst value reported by dma_get_slave_caps API.
Based on that, if the transfer is larger than what can be handled by the
DMA channel, we split the transfer into several scatterlist elements.
[hverkuil: fix checkpatch parenthesis alignment warning]
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Don't populate the read-only array range on the stack but
instead it static. Also makes the object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Don't populate the read-only array probe_ports on the stack but
instead it static const. Also makes the object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Don't populate the read-only array regs_to_read on the stack but
instead it static const. Also makes the object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Commit 2161536516 ("media: media/pci: set device_caps in struct video_device")
introduced a regression: V4L2_CAP_TUNER is always present in device_caps,
even when the device has no tuner.
This causes a warning:
WARNING: CPU: 0 PID: 249 at drivers/media/v4l2-core/v4l2-ioctl.c:1102 v4l_querycap+0xa0/0xb0 [videodev]
Fixes: 2161536516 ("media: media/pci: set device_caps in struct video_device")
Signed-off-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
V4L2_PIX_FMT_NV12 requires num_planes equals to 1,
V4L2_PIX_FMT_NV12M requires num_planes equals to 2.
and mxc-jpeg supports 2 planes for nv12,
so we should use 4L2_PIX_FMT_NV12M instead of V4L2_PIX_FMT_NV12,
otherwise it will confuses gstreamer and prevent encoding and decoding.
Signed-off-by: Ming Qian <ming.qian@nxp.com>
Signed-off-by: Shijie Qin <shijie.qin@nxp.com>
Signed-off-by: Zhou Peng <eagle.zhou@nxp.com>
Reviewed-by: Mirela Rabulea <mirela.rabulea@oss.nxp.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Drivers should generally not print anything for a successful probe, and
printing "success" before probe is done makes no sense.
Drop the unnecessary and misleading dev_info() call from probe.
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver allocates and registers two platform device structures during
probe, but the devices were never deregistered on driver unbind.
This results in a use-after-free on driver unbind as the device
structures were allocated using devres and would be freed by driver
core when remove() returns.
Fix this by adding the missing deregistration calls to the remove()
callback and failing probe on registration errors.
Note that the platform device structures must be freed using a proper
release callback to avoid leaking associated resources like device
names.
Fixes: 479f7a1181 ("[media] davinci: vpif: adaptions for DT support")
Cc: stable@vger.kernel.org # 4.12
Cc: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Make sure to disable runtime PM before returning on probe errors.
Fixes: 479f7a1181 ("[media] davinci: vpif: adaptions for DT support")
Cc: stable@vger.kernel.org
Cc: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The Google Brask device uses the same approach as the Google Fizz
which enables the HDMI CEC via the cros-ec-cec driver.
Signed-off-by: Zhuohao Lee <zhuohao@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the macro 'swap()' defined in 'include/linux/minmax.h' to avoid
opencoding it.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: David Yang <davidcomponentone@gmail.com>
Signed-off-by: Yang Guang <yang.guang5@zte.com.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The return value of devm_kzalloc() needs to be checked.
To avoid use of null pointer in case of thefailure of alloc.
Fixes: 46233e91fa ("media: mtk-vcodec: move firmware implementations into their own files")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
DST_QUEUE_OFF_BASE is applied to offset/mem_offset on MMAP capture buffers
only for the VIDIOC_QUERYBUF ioctl, while the userspace fields (including
offset/mem_offset) are filled in for VIDIOC_{QUERY,PREPARE,Q,DQ}BUF
ioctls. This leads to differences in the values presented to userspace.
If userspace attempts to mmap the capture buffer directly using values
from DQBUF, it will fail.
Move the code that applies the magic offset into a helper, and call
that helper from all four ioctl entry points.
[hverkuil: drop unnecessary '= 0' in v4l2_m2m_querybuf() for ret]
Fixes: 7f98639def ("V4L/DVB: add memory-to-memory device helper framework for videobuf")
Fixes: 908a0d7c58 ("[media] v4l: mem2mem: port to videobuf2")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The error injection controls that test wrap-around sequence and timestamp
counters were partially broken. Add a menu option for 64 or 32 bit signed
timestamp wrapping. Prevent the timestamp from wrapping around before the
device can be tested. Remove the sequence count from the timestamp
calculation so that sequence wrapping does not interfere with the
timestamp. Add consistent time and sequence wrapping to sdr and touch
devices.
Signed-off-by: Deborah Brouwer <deborahbrouwer3563@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Currently capturing grey format produces page faults
on both selfpath and mainpath. To support greyscale
we can capture YUV422 planar format and configure the U, V
buffers to the dummy buffer.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Similar to the SM8250 the CSID relies on the VFE to be clocked prior to
taking the CSID out of reset.
Apply the same fixup to SDM845 as SM8250.
Suggested-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The sm8250 CAMSS CSID depends on the VFE it is attached to being powered on
and clocked prior to taking the CSID out of reset.
It is possible to open just the CSID subdev from libcamera and attempt to
bring the CSID block up.
If we do not first bring up the VFE the CSID will fail to come out of
reset.
Tested-by: Julian Grahsl <jgrahsl@snap.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Downstream makes some pretty explicit comments about voting for bus
bandwidth prior to camcc_camnoc_axi_clk_src. Working with camx downstream
also shows that the bandwidth vote is required to get that root clock
working.
Add a simple mechanism to declare set and unset named NOCs. Whereas the
objective is to enable the sm8250 specifically the code has been
implemented to allow setting of whatever NOCs different SoCs using this
driver may require.
Tested-by: Julian Grahsl <jgrahsl@snap.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The Titan 480 camss found on SM8250 has 6 CSIPHY and 4 VFE/CSID.
CSID is compatible with the Titan 170 CSID, but the Titan 480 CSID are
inside the VFE region (between the "top" and "bus" registers), so a
workaround is added to avoid ioremap failure.
[bod] Fixed setting camnoc_axi_clk_src instead of camcc_camnoc_axi_clk
[jgrahsl, bod] Add slow_ahb_src clock values
[jgrahsl, bod] Add cpa_ahb clock values
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Julian Grahsl <jgrahsl@snap.com>
Co-developed-by: Julian Grahsl <jgrahsl@snap.com>
Signed-off-by: Julian Grahsl <jgrahsl@snap.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Co-developed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add this common format to the various format lists relevant to sdm845.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for VFE found on SM8250 (Titan 480). This implementation is
based on the titan 170 implementation. It supports the normal and lite VFE,
and only supports the RDI0 capture path.
[bod: Updates hw_version callback]
[bod: Use static inline for macros reusing parameters checkpatch --strict]
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Julian Grahsl <jgrahsl@snap.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This function waits for halt_complete but doesn't do anything to cause
it to complete, and always hits the "VFE halt timeout" error. Just delete
this code for now.
Fixes: 7319cdf189 ("media: camss: Add support for VFE hardware version Titan 170")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Julian Grahsl <jgrahsl@snap.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This isn't used and only works because devm_regulator_get() returns a dummy
regulator.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Julian Grahsl <jgrahsl@snap.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
At least for titan HW, CSID don't have an associated regulator. This change
is necessary to be able to model this in the CSID resources.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Julian Grahsl <jgrahsl@snap.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the "HALT_CMD_RESUME_AT_FRAME_BOUNDARY" define instead of a "1" which
is otherwise confusing, and add a "HALT_CMD_HALT_AT_FRAME_BOUNDARY" which
is set when disabling.
Fixes: eebe6d00e9 ("media: camss: Add support for CSID hardware version Titan 170")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Julian Grahsl <jgrahsl@snap.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Change the IS_LITE condition so that it returns true for the second lite
vfe found on titan 480 hardware (8250), which will have id == 3.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Julian Grahsl <jgrahsl@snap.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This is a leftover from my original patches, it doesn't serve any purpose.
(it was a reminder to figure out how downstream sets a particular field in
the register).
Fixes: eebe6d00e9 ("media: camss: Add support for CSID hardware version Titan 170")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Julian Grahsl <jgrahsl@snap.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
csid_isr() only checks for the reset irq, so enabling any other irqs
doesn't make sense. The "RDI irq" comment is also wrong, the register
should be CSID_CSI2_RDIN_IRQ_MASK. Without this fix there may be an
excessive amount of irqs.
Fixes: eebe6d00e9 ("media: camss: Add support for CSID hardware version Titan 170")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Julian Grahsl <jgrahsl@snap.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the decode_format/data_type from the "format" struct instead of a
hardcoded 10-bit format.
Fixes: eebe6d00e9 ("media: camss: Add support for CSID hardware version Titan 170")
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Julian Grahsl <jgrahsl@snap.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for CSIPHY (2PH/DPHY mode) found on SM8250 hardware.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Julian Grahsl <jgrahsl@snap.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver does nothing with the interrupts, so set the irq mask registers
to zero to avoid wasting CPU time for nothing.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Julian Grahsl <jgrahsl@snap.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Avoid unnecessary noise in normal usage (it prints every time CSIPHY is
powered on).
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Julian Grahsl <jgrahsl@snap.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
-----BEGIN PGP SIGNATURE-----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=RKW4
-----END PGP SIGNATURE-----
Merge tag 'bitmap-5.17-rc1' of git://github.com/norov/linux
Pull bitmap updates from Yury Norov:
- introduce for_each_set_bitrange()
- use find_first_*_bit() instead of find_next_*_bit() where possible
- unify for_each_bit() macros
* tag 'bitmap-5.17-rc1' of git://github.com/norov/linux:
vsprintf: rework bitmap_list_string
lib: bitmap: add performance test for bitmap_print_to_pagebuf
bitmap: unify find_bit operations
mm/percpu: micro-optimize pcpu_is_populated()
Replace for_each_*_bit_from() with for_each_*_bit() where appropriate
find: micro-optimize for_each_{set,clear}_bit()
include/linux: move for_each_bit() macros from bitops.h to find.h
cpumask: replace cpumask_next_* with cpumask_first_* where appropriate
tools: sync tools/bitmap with mother linux
all: replace find_next{,_zero}_bit with find_first{,_zero}_bit where appropriate
cpumask: use find_first_and_bit()
lib: add find_first_and_bit()
arch: remove GENERIC_FIND_FIRST_BIT entirely
include: move find.h from asm_generic to linux
bitops: move find_bit_*_le functions from le.h to find.h
bitops: protect find_first_{,zero}_bit properly
find_first{,_zero}_bit is a more effective analogue of 'next' version if
start == 0. This patch replaces 'next' with 'first' where things look
trivial.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Make digital tuning store the bandwidth in Hz in the private dev struct,
rather than the hardware-specific bandwidth property code, so that the
get_bandwidth() function returns the bandwidth in Hz, just as it already
does when using analog tuning.
Link: https://lore.kernel.org/linux-media/trinity-931c0e68-88af-46cc-91a1-986754798a4f-1641509499366@3c-app-gmx-bap68
Reported-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Commit 98c65a3dac ("media: si2157: add support for 1.7MHz and 6.1
MHz") introduced two bugs: The 6.1MHz setting was always used for any
bandwidth less than 7MHz due to missing "else" keywords, and then the
setting was not specified as decimal 10, but as hexadecimal 0x10, which
makes the tuner refuse the tune command. In sum, it is not possible to
tune to any channels of less than 7MHz bandwidth anymore.
Add the missing "else" keywords and convert all bandwidth settings to
decimal to avoid any future decimal vs. hexadecimal confusion.
Remove the use of the undefined bandwidth setting 0x0f for bandwidths
greater than 8MHz, which is also refused by the tune command, in favour
of using the default bandwidth setting 8 for any bandwidths greater than
7MHz.
Link: https://lore.kernel.org/linux-media/trinity-d0015ea1-1da5-4c7d-a75b-781fb26dc339-1641509387112@3c-app-gmx-bap68
Fixes: 98c65a3dac ("media: si2157: add support for 1.7MHz and 6.1 MHz")
Reported-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Some sensors come with a variable-focus lens where the lens focus is
controller by a VCM (Voice Coil Motor). If there is a VCM for the
lens-focus, and if so which one, is described on the vcm_type field
of the ACPI SSDB table.
These VCMs are a second I2C device listed as an extra I2cSerialBusV2
resource in the same ACPI device as the sensor. The i2c-core-acpi.c
code only instantiates an i2c-client for the first I2cSerialBusV2
resource.
Add support for instantiating an i2c-client for the VCM with
the type of the i2c-client set based on the SSDB vcm_type field.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Since cio2_bridge_init() may now return -EPROBE_DEFER it is best to
call it before anything else.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
On devices where things are not fully describe in devicetree (1)
and where the code thus falls back to calling cio2_bridge_init(),
the i2c-clients for any VCMs also need to be instantiated manually.
The VCM can be probed by its driver as soon as the code instantiates
the i2c-client and this probing must not happen before the PMIC is
fully setup.
Make cio2_bridge_init() return -EPROBE_DEFER when the PMIC is not
fully-setup, deferring the probe of the ipu3-cio2 driver.
This is a preparation patch for adding VCM enumeration support to
the ipu3-cio2-bridge code.
1) Through embedding of devicetree info in the ACPI tables
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In cases like this when controlling regulators and clocks the suspend()
and resume() functions are meant to be called balanced toggling the behaviour.
It's wrong to use the same suspend function for runtime and system suspend
in this case and leads to errors like
[ 77.718890] Failed to disable vddd: -EIO
Use pm_runtime_force_* helpers in order to support system suspend properly
when runtime pm is already implemented and fix this.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
regulator_bulk_disable can fail and thus suspend() can. Handle that error
gracefully.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Tell ACPI device PM code that the driver supports the device being in
non-zero ACPI D state when the driver's probe function is entered.
Also do identification on the first access of the device, whether in probe
or when starting streaming.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Kao, Arec <arec.kao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Tell ACPI device PM code that the driver supports the device being in
non-zero ACPI D state when the driver's probe function is entered.
Also do identification on the first access of the device, whether in probe
or when starting streaming.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Tell ACPI device PM code that the driver supports the device being in
non-zero ACPI D state when the driver's probe function is entered.
Also do identification on the first access of the device, whether in probe
or when starting streaming.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Tell ACPI device PM code that the driver supports the device being in
non-zero ACPI D state when the driver's probe function is entered.
Also do identification on the first access of the device, whether in probe
or when starting streaming.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Tell ACPI device PM code that the driver supports the device being in
non-zero ACPI D state when the driver's probe function is entered.
Also do identification on the first access of the device, whether in probe
or when starting streaming.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Tell ACPI device PM code that the driver supports the device being in
non-zero ACPI D state when the driver's probe function is entered.
Also do identification on the first access of the device, whether in probe
or when starting streaming.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If powering on the sensor failed, the entire power-off sequence was run
independently of how far the power-on sequence proceeded before the error.
This lead to disabling regulators and/or clock that was not enabled.
Fix this by disabling only clocks and regulators that were enabled
previously.
Fixes: 11c0d8fdcc ("media: i2c: Add support for the OV8865 image sensor")
Cc: stable@vger.kernel.org
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hyungwoo's e-mail no longer works so I presume he's left the company. Drop
Hyungwoo as maintainer on ov5670 driver and remove his e-mail from other
sensor drivers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This device also supports ATV, as it has the same API for
setting analog TV tuning parameters.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Some tuners allow setting the bandwidth filter to 1.7MHz and
6.1 MHz. Add support for it upstream, as the narrower is the
bandwidth filter, the better.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Those two delivery systems are supported by some of the si2146
tuners, but the current code is missing the setup for those.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver should be capable of autodetecting its type, so no
need to pass it via device driver's data.
While here, improve documentation of some of the part_id
specific code.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Each chip at the si21xx TER family seems to have a different firmware,
with seems to actually be a patch against the ROM code.
Rework the code in order to use different firmware files depending
on the chip ID and rom ID.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Loading a firmware file should not be mandatory, as devices
could work with an eeprom firmware, if available.
Yet, using the eeprom firmware could lead into unpredictable
results, so the best is to warn about that.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Si2157 (A30) is functional with the ROM firmware 3.0.5, but can also
be patched at runtime, e.g. to firmware 3.1.3. However, although a
firmware filename for its firmware patch exists, that has only been used
for the Si2177 (A30) so far (which indeed takes the binary identical
firmware patch).
Add support for downloading firmware patches into the Si2157 (A30), but
make it optional, so that initialization can succeed with and without a
firmware patch being available. Keep the use of request_firmware() for
this purpose rather than firmware_request_nowarn(), so that the warning
in the log makes users aware that it is possible to provide a firmware
for this tuner.
The firmware patch is probably also optional for other (if not all)
tuners supported by the driver, but since I do not have the others
available to test, they are kept mandatory for now to avoid regressions.
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Split the firmware load code from si2157_init, in order to
help to add further changes at the way firmware is handled on
this device.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Static variables do not need to be initialised to 0, because compiler
will initialise all uninitialised statics to 0. Thus, remove the
unneeded initializations.
Link: https://lore.kernel.org/linux-media/20211212070918.289617-1-wangborong@cdjrlc.com
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
return value form directly instead of
taking this in another redundant variable.
Link: https://lore.kernel.org/linux-media/20211210024721.425145-1-chi.minghao@zte.com.cn
Reported-by: Zeal Robot <zealci@zte.com.cm>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
return value form directly instead of
taking this in another redundant variable.
Link: https://lore.kernel.org/linux-media/20211209015009.409428-1-chi.minghao@zte.com.cn
Reported-by: Zeal Robot <zealci@zte.com.cm>
Signed-off-by: chiminghao <chi.minghao@zte.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Jacopo Mondi