Commit c7299fea67 ("spi: Fix spi device unregister flow") changed the
SPI core's behavior if the ->setup() hook returns an error upon adding
an spi_device: Before, the ->cleanup() hook was invoked to free any
allocations that were made by ->setup(). With the commit, that's no
longer the case, so the ->setup() hook is expected to free the
allocations itself.
I've identified 5 drivers which depend on the old behavior and am fixing
them up hereinafter: spi-bitbang.c spi-fsl-spi.c spi-omap-uwire.c
spi-omap2-mcspi.c spi-pxa2xx.c
Importantly, ->setup() is not only invoked on spi_device *addition*:
It may subsequently be called to *change* SPI parameters. If changing
these SPI parameters fails, freeing memory allocations would be wrong.
That should only be done if the spi_device is finally destroyed.
I am therefore using a bool "initial_setup" in 4 of the affected drivers
to differentiate between the invocation on *adding* the spi_device and
any subsequent invocations: spi-bitbang.c spi-fsl-spi.c spi-omap-uwire.c
spi-omap2-mcspi.c
In spi-pxa2xx.c, it seems the ->setup() hook can only fail on spi_device
addition, not any subsequent calls. It therefore doesn't need the bool.
It's worth noting that 5 other drivers already perform a cleanup if the
->setup() hook fails. Before c7299fea67, they caused a double-free
if ->setup() failed on spi_device addition. Since the commit, they're
fine. These drivers are: spi-mpc512x-psc.c spi-pl022.c spi-s3c64xx.c
spi-st-ssc4.c spi-tegra114.c
(spi-pxa2xx.c also already performs a cleanup, but only in one of
several error paths.)
Fixes: c7299fea67 ("spi: Fix spi device unregister flow")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Saravana Kannan <saravanak@google.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> # pxa2xx
Link: https://lore.kernel.org/r/f76a0599469f265b69c371538794101fa37b5536.1622149321.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the missing iounmap() before return from of_fsl_spi_probe()
in the error handling case.
Fixes: 0f0581b24b ("spi: fsl: Convert to use CS GPIO descriptors")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210401140350.1677925-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 7a2da5d796 ("spi: fsl: Fix driver breakage when SPI_CS_HIGH
is not set in spi->mode") broke our MPC8309 board by effectively
inverting the boolean value passed to fsl_spi_cs_control. The
SPISEL_BOOT signal is used as chipselect, but it's not a gpio, so
we cannot rely on gpiolib handling the polarity.
Adapt to the new world order by inverting the logic here. This does
assume that the slave sitting at the SPISEL_BOOT is active low, but
should that ever turn out not to be the case, one can create a stub
gpiochip driver controlling a single gpio (or rather, a single "spo",
special-purpose output).
Fixes: 7a2da5d796 ("spi: fsl: Fix driver breakage when SPI_CS_HIGH is not set in spi->mode")
Cc: stable@vger.kernel.org
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Link: https://lore.kernel.org/r/20210130143545.505613-1-rasmus.villemoes@prevas.dk
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 766c6b63aa ("spi: fix client driver breakages when using GPIO
descriptors") broke fsl spi driver.
As now we fully rely on gpiolib for handling the polarity of
chip selects, the driver shall not alter the GPIO value anymore
when SPI_CS_HIGH is not set in spi->mode.
Fixes: 766c6b63aa ("spi: fix client driver breakages when using GPIO descriptors")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/6b51cc2bfbca70d3e9b9da7b7aa4c7a9d793ca0e.1610629002.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 0f0581b24b ("spi: fsl: Convert to use CS GPIO descriptors")
broke the use of the SPISEL_BOOT signal as a chip select on the
MPC8309.
pdata->max_chipselect, which becomes master->num_chipselect, must be
initialized to take into account the possibility that there's one more
chip select in use than the number of GPIO chip selects.
Cc: stable@vger.kernel.org # v5.4+
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Fixes: 0f0581b24b ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Link: https://lore.kernel.org/r/20201127152947.376-1-rasmus.villemoes@prevas.dk
Signed-off-by: Mark Brown <broonie@kernel.org>
The field mspi->reg_base is annotated as an __iomem pointer. Good.
However, this field is often assigned to a temporary variable:
before being used. For example:
struct fsl_spi_reg *reg_base = mspi->reg_base;
But this variable is missing the __iomem annotation.
So, add the missing __iomem and make sparse & the bot happier.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Link: https://lore.kernel.org/r/20200622162611.83694-1-luc.vanoostenryck@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Unlike irq_of_parse_and_map() which has a dummy definition on SPARC,
of_irq_to_resource() hasn't.
But as platform_get_irq() can be used instead and is generic, use it.
Reported-by: kbuild test robot <lkp@intel.com>
Suggested-by: Mark Brown <broonie@kernel.org>
Fixes: 3194d2533e ("spi: fsl: don't map irq during probe")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/091a277fd0b3356dca1e29858c1c96983fc9cb25.1576172743.git.christophe.leroy@c-s.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
The Freescale MPC8xxx had a special quirk for handling a
single hardwired chipselect, the case when we're using neither
GPIO nor native chip select: when inspecting the device tree
and finding zero "cs-gpios" on the device node the code would
assume we have a single hardwired chipselect that leaves the
device always selected.
This quirk is not handled by the new core code, so we need
to check the "cs-gpios" explicitly in the driver and set
pdata->max_chipselect = 1 which will later fall through to
the SPI master ->num_chipselect.
Make sure not to assign the chip select handler in this
case: there is no handling needed since the chip is always
selected, and this is what the old code did as well.
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 0f0581b24b ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr> (No tested the
Link: https://lore.kernel.org/r/20191128083718.39177-3-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
This makes the driver actually support looking up GPIO
descriptor. A coding mistake in the initial descriptor
support patch was that it was failing to turn on the very
feature it was implementing. Mea culpa.
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reported-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 0f0581b24b ("spi: fsl: Convert to use CS GPIO descriptors")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Link: https://lore.kernel.org/r/20191128083718.39177-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
For many places in the spi drivers, using the new `spi_transfer_delay`
helper is straightforward.
It's just replacing:
```
if (t->delay_usecs)
udelay(t->delay_usecs);
```
with `spi_transfer_delay(t)` which handles both `delay_usecs` and the new
`delay` field.
This change replaces in all places (in the spi drivers) where this change
is simple.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-10-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the Freescale SPI master driver to use GPIO
descriptors for chip select handling.
The Freescale (fsl) driver has a lot of quirks to look up
"gpios" rather than "cs-gpios" from the device tree.
After the prior patch that will make gpiolib return the
GPIO descriptor for "gpios" in response to a request for
"cs-gpios", this code can be cut down quite a bit.
The driver has custom handling of chip select rather
than using the core (which may be possible but not
done in this patch) so it still needs to refer directly
to spi->cs_gpiod to set the chip select.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190804003539.985-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
A small set of fixes here, one core fix for error handling when we fail
to set up the hardware before initiating a transfer and another one
reverting a change in the core which broke Raspberry Pi in common use
cases as part of some optimization work. There's also a couple of
driver specific fixes.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlz+aEETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0EdhB/9pSAaTxpo2LmLY11WDqCll5E5wwV0n
twjqcJkCpik2gp08xf/l1C563XvaAEUmidMGjpSGNhbd+UFUY4jBksDZd8t+phNA
lOFL03sWxUGd46SvsYCLByzIu1dp8LKQ7JkDvb+OChDMai9YyeHwF4Pl7L7EHI6P
yB3m84o3X82NnVxZJZAkim27Bn1LMcmKvFJxiLPyzycdI41+Vzf+Hx0dSzTKHKXb
wbh3tsSok1l3NHOW0xXCf8pG5KtBeISo7RxQE2XuVkxB3LcEbbbG+Q1NvBHQLmty
VtSkLUGc3+mUdaaIh2CW3AkECRtkPG6qngBns0NScXca4xQ9/J3X4zlg
=ktil
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A small set of fixes here.
One core fix for error handling when we fail to set up the hardware
before initiating a transfer and another one reverting a change in the
core which broke Raspberry Pi in common use cases as part of some
optimization work.
There's also a couple of driver specific fixes"
* tag 'spi-fix-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: abort spi_sync if failed to prepare_transfer_hardware
spi: spi-fsl-spi: call spi_finalize_current_message() at the end
spi: bitbang: Fix NULL pointer dereference in spi_unregister_master
spi: Fix Raspberry Pi breakage
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
spi_finalize_current_message() shall be called once all
actions are finished, otherwise the last actions might
step over a newly started transfer.
Fixes: c592becbe7 ("spi: fsl-(e)spi: migrate to generic master queueing")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Taking one interrupt for every byte is rather slow. Since the
controller is perfectly capable of transmitting 32 bits at a time,
change t->bits_per-word to 32 when the length is divisible by 4 and
large enough that the reduced number of interrupts easily compensates
for the one or two extra fsl_spi_setup_transfer() calls this causes.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit c9bfcb3151 (spi_mpc83xx: much improved driver) introduced
logic to ensure bits_per_word and speed_hz stay the same for a series
of spi_transfers with CS active, arguing that
The current driver may cause glitches on SPI CLK line since one
must disable the SPI controller before changing any HW settings.
This sounds quite reasonable. So this is a quite naive attempt at
relaxing this sanity checking to only ensure that speed_hz is
constant - in the faint hope that if we do not causes changes to the
clock-related fields of the SPMODE register (DIV16 and PM), those
glitches won't appear.
The purpose of this change is to allow automatically optimizing large
transfers to use 32 bits-per-word; taking one interrupt for every byte
is extremely slow.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The comment says that we should not allow changes (to
bits_per_word/speed_hz) while CS is active, and indeed the code below
does fsl_spi_setup_transfer() when the ->cs_change of the previous
spi_transfer was set (and for the very first transfer).
So the sanity checking is a bit too strict - we can change it to
follow the same logic as is used by the actual transfer loop.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
__spi_validate() in the generic SPI code sets ->speed_hz and
->bits_per_word to non-zero values, so this condition is always true.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MPC8309 has a dedicated signal, SPISEL_BOOT, usually used as chip
select for the flash device from which the bootloader is loaded. It is
not an ordinary gpio, but is simply controlled via the SPI_CS register
in the system configuration.
To allow accessing such a spi slave, we need to teach
fsl_spi_cs_control() how to control the SPISEL_BOOT signal. To
distinguish the gpio-controlled slaves, continue to have those use
chip_select values of 0..ngpios-1, and use chip_select == ngpios for
the boot flash.
I'm not too happy with all the ifdeffery, but it seems to be necessary
for guarding the sysdev/fsl_soc.h and use of
get_immrbase() (spi-fsl-lib.c already contains similar ifdeffery).
Googling suggests that the MPC8306 is similar, with the SPI_CS
register at the same offset.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Irq_dispose_mapping should be called in err path to release
the resources that irq_of_parse_and_map requested.
Signed-off-by: Liu Xiang <liu.xiang6@zte.com.cn>
Signed-off-by: Mark Brown <broonie@kernel.org>
The script "checkpatch.pl" pointed information out like the following.
WARNING: quoted string split across lines
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus reuse the corresponding function "kcalloc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kmalloc_array".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that most cleanup is done automatically the remove functions
can be significantly simplified.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Migrate fsl-espi and fsl-spi to using the managed devm_ functions
for resource handling. This simplifies the cleanup.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Since commit c592becbe7 ("spi: fsl-(e)spi: migrate to generic master
queueing") the function fsl_spi_do_one_msg() is not void anymore, so return
an error code to avoid the following buid warning:
drivers/spi/spi-fsl-spi.c: In function 'fsl_spi_do_one_msg':
>> drivers/spi/spi-fsl-spi.c:374:4: warning: 'return' with no value, in function returning non-void [-Wreturn-type]
return;
^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Migrates the fsl-(e)spi driver to use the generic master queuing.
Avoids the "master is unqueued, this is deprecated" warning.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sort all the include headers alphabetically for the freescale
spi drivers. If the inlcude headers sorted out of order, maybe
the best logical choice is to append new ones after the exist
ones, while this may create a lot of potential for duplicates
and conflicts for each diffenent changes will add new headers
in the same location.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
mpc8xxx_spi_probe() has set master->cleanup = mpc8xxx_spi_cleanup,
however current code overrides the setting in fsl_spi_probe() and set
master->cleanup = fsl_spi_cleanup.
Thus the memory allocated for cs is not freed anywhere.
Convert to use devm_kzalloc to fix the memory leak.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 1e25cd4729 "spi: Do not require a completion", this checking is
required to prevent NULL pointer dereference.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
fsl_spi_grlib_probe() may update mpc8xxx_spi->max_bits_per_word setting.
So set master->bits_per_word_mask after fsl_spi_grlib_probe().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When used via spidev with more than one messages to tranfer via
SPI_IOC_MESSAGE the current implementation would return with
-EINVAL, since bits_per_word and speed_hz are set in all
transfer structs. And in the 2nd loop status will stay at
-EINVAL as its not overwritten again via fsl_spi_setup_transfer().
This patch changes this behavious by first checking if one of
the messages uses different settings. If this is the case
the function will return with -EINVAL. If not, the messages
are transferred correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=LeaW
-----END PGP SIGNATURE-----
Merge tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull PTR_RET() removal patches from Rusty Russell:
"PTR_RET() is a weird name, and led to some confusing usage. We ended
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle"
[ There are still some PTR_RET users scattered about, with some of them
possibly being new, but most of them existing in Rusty's tree too. We
have that
#define PTR_RET(p) PTR_ERR_OR_ZERO(p)
thing in <linux/err.h>, so they continue to work for now - Linus ]
* tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
GFS2: Replace PTR_RET with PTR_ERR_OR_ZERO
Btrfs: volume: Replace PTR_RET with PTR_ERR_OR_ZERO
drm/cma: Replace PTR_RET with PTR_ERR_OR_ZERO
sh_veu: Replace PTR_RET with PTR_ERR_OR_ZERO
dma-buf: Replace PTR_RET with PTR_ERR_OR_ZERO
drivers/rtc: Replace PTR_RET with PTR_ERR_OR_ZERO
mm/oom_kill: remove weird use of ERR_PTR()/PTR_ERR().
staging/zcache: don't use PTR_RET().
remoteproc: don't use PTR_RET().
pinctrl: don't use PTR_RET().
acpi: Replace weird use of PTR_RET.
s390: Replace weird use of PTR_RET.
PTR_RET is now PTR_ERR_OR_ZERO(): Replace most.
PTR_RET is now PTR_ERR_OR_ZERO
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This relies upon of_spi_register_master to find out which gpios to use.
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Lukas Wunner