Add ISO sensitivity and ISO auto/manual controls. The sensitivity
values are related to level of amplification of the analog signal
between image sensor and ADC. These controls allow to support sensors
exposing an interface to accept the ISO values directly.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add V4L2_CID_IMAGE_STABILIZATION control for the camera image
stabilization feature. This control can be used to enable/disable
image stabilization. It might get converted to a menu control
in future if more options are needed.
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add V4L2_CID_WIDE_DYNAMIC_RANGE camera class control for the
camera wide dynamic range (WDR, HDR) feature. This control
can be used to enable/disable wide dynamic range. It might
get converted to a menu control in future if more options
are needed.
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds V4L2_CID_AUTO_N_PRESET_WHITE_BALANCE control which is
an extended version of the V4L2_CID_AUTO_WHITE_BALANCE control,
including white balance presets. The following presets are defined:
- V4L2_WHITE_BALANCE_INCANDESCENT,
- V4L2_WHITE_BALANCE_FLUORESCENT,
- V4L2_WHITE_BALANCE_FLUORESCENT_H,
- V4L2_WHITE_BALANCE_HORIZON,
- V4L2_WHITE_BALANCE_DAYLIGHT,
- V4L2_WHITE_BALANCE_FLASH,
- V4L2_WHITE_BALANCE_CLOUDY,
- V4L2_WHITE_BALANCE_SHADE.
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The camera may in some conditions incorrectly determine the exposure,
and a manual automatic exposure correction may be needed. This patch
adds V4L2_CID_AUTO_EXPOSURE_BIAS control which allows to add some
offset in the automatic exposure control loop, to compensate for
frame under- or over-exposure.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds definition of additional color effects:
- V4L2_COLORFX_AQUA,
- V4L2_COLORFX_ART_FREEZE,
- V4L2_COLORFX_SILHOUETTE,
- V4L2_COLORFX_SOLARIZATION,
- V4L2_COLORFX_ANTIQUE,
- V4L2_COLORFX_SET_CBCR.
The new V4L2_COLORFX_CBCR control is added to allow setting
the fixed Cb, Cr values that replace chroma Cb/Cr coefficients
in case of V4L2_COLORFX_SET_CBCR effect.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add three other colour orders for 10-bit to 8-bit DPCM compressed raw bayer
pixel formats.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add control class for image processing controls. The control class deals
with controls processing image, for example digital gain or noise filtering,
which can be present in any part of the pipeline.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add image source control class. This control class is intended to contain
low level controls which deal with control of the image capture process ---
the A/D converter in image sensors, for example.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2 uses the enum type in IOCTL arguments in IOCTLs that were defined until
the use of enum was considered less than ideal. Recently Rémi Denis-Courmont
brought up the issue by proposing a patch to convert the enums to unsigned:
<URL:http://www.spinics.net/lists/linux-media/msg46167.html>
This sparked a long discussion where another solution to the issue was
proposed: two sets of IOCTL structures, one with __u32 and the other with
enums, and conversion code between the two:
<URL:http://www.spinics.net/lists/linux-media/msg47168.html>
Both approaches implement a complete solution that resolves the problem. The
first one is simple but requires assuming enums and __u32 are the same in
size (so we won't break the ABI) while the second one is more complex and
less clean but does not require making that assumption.
The issue boils down to whether enums are fundamentally different from __u32
or not, and can the former be substituted by the latter. During the
discussion it was concluded that the __u32 has the same size as enums on all
archs Linux is supported: it has not been shown that replacing those enums
in IOCTL arguments would break neither source or binary compatibility. If no
such reason is found, just replacing the enums with __u32s is the way to go.
This is what this patch does. This patch is slightly different from Remi's
first RFC (link above): it uses __u32 instead of unsigned and also changes
the arguments of VIDIOC_G_PRIORITY and VIDIOC_S_PRIORITY.
Signed-off-by: Rémi Denis-Courmont <remi@remlab.net>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull media fixes from Mauro Carvalho Chehab:
- Fixes a regression at DVB core when switching from DVB-S2 to DVB-S on
Kaffeine (Fedora 16 Bugzilla #812895);
- Fixes a mutex unlock at an error condition at drx-k;
- Fix winbond-cir set mode;
- mt9m032: Fix a compilation breakage with some random Kconfig;
- mt9m032: fix two dead locks;
- xc5000: don't require an special firmware (that won't be provided by
the vendor) just because the xtal frequency is different;
- V4L DocBook: fix some typos at multi-plane formats description.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] xc5000: support 32MHz & 31.875MHz xtal using the 41.024.5 firmware
[media] V4L: mt9m032: fix compilation breakage
[media] V4L: DocBook: Fix typos in the multi-plane formats description
[media] V4L: mt9m032: fix two dead-locks
[media] rc-core: set mode for winbond-cir
[media] drxk: Does not unlock mutex if sanity check failed in scu_command()
[media] dvb_frontend: Fix a regression when switching back to DVB-S
This patch fixes following compilation warning:
Error: no ID for constraint linkend: v4l2-jpeg-chroma-subsampling.
and adds missing JPEG control class at the Table A.58.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These two IOCTLS are obsoleted by VIDIOC_SUBDEV_G_SELECTION and
VIDIOC_SUBDEV_S_SELECTION. Mark them obsolete.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add documentation for V4L2 subdev selection API. This changes also
experimental V4L2 subdev API so that scaling now works through selection API
only.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* poll: (5970 commits)
poll: add poll_requested_events() and poll_does_not_wait() functions
crc32: select an algorithm via Kconfig
crc32: add self-test code for crc32c
crypto: crc32c should use library implementation
crc32: bolt on crc32c
crc32: add note about this patchset to crc32.c
crc32: optimize loop counter for x86
crc32: add slice-by-8 algorithm to existing code
crc32: make CRC_*_BITS definition correspond to actual bit counts
crc32: fix mixing of endian-specific types
crc32: miscellaneous cleanups
crc32: simplify unit test code
crc32: move long comment about crc32 fundamentals to Documentation/
crc32: remove two instances of trailing whitespaces
checkpatch: check for quoted strings broken across lines
checkpatch: whitespace - add/remove blank lines
checkpatch: warn on use of yield()
checkpatch: add --strict tests for braces, comments and casts
checkpatch: add [] to type extensions
checkpatch: high precedence operators do not require additional parentheses in #defines
...
Pull media updates from Mauro Carvalho Chehab:
- V4L2 API additions to better support JPEG compression control
- media API additions to properly support MPEG decoders
- V4L2 API additions for image crop/scaling
- a few other V4L2 API DocBook fixes/improvements
- two new DVB frontend drivers: m88rs2000 and rtl2830
- two new DVB drivers: az6007 and rtl28xxu
- a framework for ISA drivers, that removed lots of common code found
at the ISA radio drivers
- a new FM transmitter driver (radio-keene)
- a GPIO-based IR receiver driver
- a new sensor driver: mt9m032
- some new video drivers: adv7183, blackfin, mx2_emmaprp, sii9234_drv,
vs6624
- several new board additions, driver fixes, improvements and cleanups.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (295 commits)
[media] update CARDLIST.em28xx
[media] partially reverts changeset fa5527c
[media] stb0899: fix the limits for signal strength values
[media] em28xx: support for 2304:0242 PCTV QuatroStick (510e)
[media] em28xx: support for 2013:0251 PCTV QuatroStick nano (520e)
[media] -EINVAL -> -ENOTTY
[media] gspca - sn9c20x: Cleanup source
[media] gspca - sn9c20x: Simplify register write for capture start/stop
[media] gspca - sn9c20x: Add automatic JPEG compression mechanism
[media] gspca - sn9c20x: Greater delay in case of sensor no response
[media] gspca - sn9c20x: Optimize the code of write sequences
[media] gspca - sn9c20x: Add the JPEG compression quality control
[media] gspca - sn9c20x: Add a delay after Omnivision sensor reset
[media] gspca - sn9c20x: Propagate USB errors to higher level
[media] gspca - sn9c20x: Use the new video control mechanism
[media] gspca - sn9c20x: Fix loss of frame start
[media] gspca - zc3xx: Lack of register 08 value for sensor cs2102k
[media] gspca - ov534_9: Add brightness to OmniVision 5621 sensor
[media] gspca - zc3xx: Add V4L2_CID_JPEG_COMPRESSION_QUALITY control support
[media] pvrusb2: fix 7MHz & 8MHz DVB-T tuner support for HVR1900 rev D1F5
...
Make the VIDIOC_G/S_SELECTION ioctls documentation more consistent
with the rest of media Docbook, use capital letters where necessary
and correct few minor errors.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a small extension to the S_HW_FREQ_SEEK ioctl: if the wrap_around
value is not support by the hardware, then -EINVAL is returned.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Here is a small patch which fixes a DocBook mistake in the decoder_cmd
documentation.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If V4L2_CAP_DEVICE_CAPS is set, then the new device_caps field is filled with
the capabilities of the opened device node.
The capabilities field traditionally contains the capabilities of the physical
device, being a superset of all capabilities available at the several device
nodes. E.g., if you open /dev/video0, then if it contains VBI caps then that means
that there is a corresponding vbi node as well. And the capabilities field of
both the video and vbi nodes should contain identical caps.
However, it would be very useful to also have a capabilities field that contains
just the caps for the currently open device, hence the new CAP bit and field.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (57 commits)
[media] as3645a: Fix compilation by including slab.h
[media] s5p-fimc: Remove linux/version.h include from fimc-mdevice.c
[media] s5p-mfc: Remove linux/version.h include from s5p_mfc.c
[media] ds3000: using logical && instead of bitwise &
[media] v4l2-ctrls: make control names consistent
[media] DVB: dib0700, add support for Nova-TD LEDs
[media] DVB: dib0700, add corrected Nova-TD frontend_attach
[media] DVB: dib0700, separate stk7070pd initialization
[media] DVB: dib0700, move Nova-TD Stick to a separate set
[media] : add MODULE_FIRMWARE to dib0700
[media] DVB-CORE: remove superfluous DTV_CMDs
[media] s5p-jpeg: adapt to recent videobuf2 changes
[media] s5p-g2d: fixed a bug in controls setting function
[media] s5p-mfc: Fix volatile controls setup
[media] drivers/media/video/s5p-mfc/s5p_mfc.c: adjust double test
[media] drivers/media/video/s5p-fimc/fimc-capture.c: adjust double test
[media] s5p-fimc: Fix incorrect control ID assignment
[media] dvb_frontend: Don't call get_frontend() if idle
[media] DocBook/dvbproperty.xml: Remove DTV_MODULATION from ISDB-T
[media] DocBook/dvbproperty.xml: Fix ISDB-T delivery system parameters
...
On ISDB-T, each layer can have its own independent modulation,
applied to the carriers that belong to the segments associated
with them. So, there's no sense to define a global modulation
parameter.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ISDB-T differs on its way to implement the hierarchical
transmissions: instead of using a low-priority/high-priority
FEC codes, it does that by using different layers, each layer
with their groups of segments. So, those parameters don't make sense
for ISDB-T.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The units for DTV_FREQUENCY are kHz for satellital delivery systems
(DVB-S/DVB-S2/DVB-TURBO/ISDB-S). Fix it at the API spec.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As per the feature removal document, make the tuner type check more strict
so that it is no longer possible to set the radio frequency through a video
node or the TV frequency through a radio node.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As Rupert pointed out, the phrase "It is good practice" should be replaced
with "You must".
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Rupert Eibauer <Rupert.Eibauer@ces.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update the spec to the behavior implemented by the control framework.
This should have been documented long ago but for some reason it was
never done.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (655 commits)
[media] revert patch: HDIC HD29L2 DMB-TH USB2.0 reference design driver
mb86a20s: Add a few more register settings at the init seq
mb86a20s: Group registers into the same line
[media] [PATCH] don't reset the delivery system on DTV_CLEAR
[media] [BUG] it913x-fe fix typo error making SNR levels unstable
[media] cx23885: Query the CX25840 during enum_input for status
[media] cx25840: Add support for g_input_status
[media] rc-videomate-m1f.c Rename to match remote controler name
[media] drivers: media: au0828: Fix dependency for VIDEO_AU0828
[media] convert drivers/media/* to use module_platform_driver()
[media] drivers: video: cx231xx: Fix dependency for VIDEO_CX231XX_DVB
[media] Exynos4 JPEG codec v4l2 driver
[media] doc: v4l: selection: choose pixels as units for selection rectangles
[media] v4l: s5p-tv: mixer: fix setup of VP scaling
[media] v4l: s5p-tv: mixer: add support for selection API
[media] v4l: emulate old crop API using extended crop/compose API
[media] doc: v4l: add documentation for selection API
[media] doc: v4l: add binary images for selection API
[media] v4l: add support for selection api
[media] hd29l2: fix review findings
...
Pixels were preferred units for selection rectangles over driver-dependent
units for almost all use cases. Therefore the units were fixed to pixels.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a documentation for VIDIOC_{G/S}_SELECTION ioctl. Moreover, the
patch adds the description of modeling of composing, cropping and scaling
features in V4L2. Finally, some examples are presented.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds images in binary format for the V4L2 selection API.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Written by Theodore Kilgore
With minor changes by Hans de Goede:
-Code style fixes
-Correct the verbose level on various PDEBUG messages
-Make error messages use pr_err instead of PDEBUG
-Document the jl20 pixel format
Signed-off-by: Theodore Kilgore <kilgota@auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mark info.type as deprecated inside the header, recommending
the usage of DTV_ENUM_DELSYS DVBv5 command instead.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The V4L2_CID_ALPHA_COMPONENT control is intended for the video capture
or memory-to-memory devices that are capable of setting up the per-pixel
alpha component to some arbitrary value. It allows to set the alpha
component for all pixels to an arbitrary value.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of using the same delivery system for both Annex A and
Annex C, split them into two separate ones. This helps to support
devices that only support Annex A.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
NV24 and NV42 are planar YCbCr 4:4:4 and YCrCb 4:4:4 formats with a
luma plane followed by an interleaved chroma plane.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This removes comment tags intended for emacs configuration from
67 files in the Media API DocBook. Such comments are not really
helpful and violate the coding style rules.
Signed-off-by: Sylwester Nawrocki <snjw23@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2_FBUF_CAP_SRC_CHROMAKEY is the opposite of V4L2_FBUF_CAP_CHROMAKEY, but
according to the documentation it was the same. The terms 'video' and
'framebuffer' were accidentally swapped in the text.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
CC: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As per discussion during the 2011 V4L-DVB workshop.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For some reason the V4L2_TUNER_CAP_RDS_CONTROLS/BLOCK_IO capabilities were never
documented in the proper table. In addition, then RDS interface section incorrectly
referred to them as V4L2_TUNER_SUB_RDS_... instead of CAP_RDS_...
This is now fixed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
DVB-C, as defined by ITU-T J.83 has 3 annexes. The differences between
Annex A and Annex C is that Annex C uses a subset of the modulation
types, and uses a different rolloff factor. A different rolloff means
that the bandwidth required is slicely different, and may affect the
saw filter configuration at the tuners. Also, some demods have different
configurations, depending on using Annex A or Annex C.
So, allow userspace to specify it, by changing the rolloff factor.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2_CID_POWER_LINE_FREQUENCY control allows applications to instruct
a driver what is the power line frequency so an appropriate filter
can be used by the device to cancel flicker by compensating the light
intensity ripple. Currently in the menu we have entries for 50 Hz and
60 Hz and for entirely disabling the anti-flicker filter.
However some devices are capable of automatically detecting the
frequency, so add V4L2_CID_POWER_LINE_FREQUENCY_AUTO entry for them.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[mchehab@redhat.com: remove emacs format crap at the end of the new files]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When satisfied with the try results, applications can set the active formats
by setting the which argument to V4L2_SUBDEV_FORMAT_ACTIVE
not V4L2_SUBDEV_FORMAT_TRY.
Signed-off-by: Jonghun Han <jonghun.han@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a new VOLATILE control flag that is set for volatile controls.
That way applications know whether the value of the control is volatile
(i.e. can change continuously) or not.
Until now this was an internal property, but it is useful to know in
userspace as well.
A typical use case is the gain value when autogain is on. In that case the
hardware will continuously adjust the gain based various environmental
factors.
This patch just adds and documents the flag, it's not yet used.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* tag 'v3.1-rc6': (1902 commits)
Linux 3.1-rc6
ioctl: register LTTng ioctl
fuse: fix memory leak
fuse: fix flock breakage
Btrfs: add dummy extent if dst offset excceeds file end in
Btrfs: calc file extent num_bytes correctly in file clone
btrfs: xattr: fix attribute removal
Btrfs: fix wrong nbytes information of the inode
Btrfs: fix the file extent gap when doing direct IO
Btrfs: fix unclosed transaction handle in btrfs_cont_expand
Btrfs: fix misuse of trans block rsv
Btrfs: reset to appropriate block rsv after orphan operations
Btrfs: skip locking if searching the commit root in csum lookup
btrfs: fix warning in iput for bad-inode
Btrfs: fix an oops when deleting snapshots
[media] vp7045: fix buffer setup
[media] nuvoton-cir: simplify raw IR sample handling
[media] [Resend] viacam: Don't explode if pci_find_bus() returns NULL
[media] v4l2: Fix documentation of the codec device controls
[media] gspca - sonixj: Fix the darkness of sensor om6802 in 320x240
...
Fixed missing ids of the codec controls description in the controls.xml file.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Move voltage and tone to DVB-S.
- Add turbo code.
- In DVB-S2 and turbo code sections, refer to DVB-S, as both
are extensions to DVB-S.
- Add modulation to DVB-S2.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Define a frame sync event to tell user space when the reception of a frame
starts.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move documentation of structures used in DQEVENT from SUBSCRIBE_EVENT to
DQEVENT.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
[media] ir-mce_kbd-decoder: include module.h for its facilities
[media] ov5642: include module.h for its facilities
[media] em28xx: Fix DVB-C maxsize for em2884
[media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
[media] v4l: mt9v032: Fix Bayer pattern
[media] V4L: mt9m111: rewrite set_pixfmt
[media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
[media] V4L: initial driver for ov5642 CMOS sensor
[media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
[media] V4L: soc-camera: remove soc-camera bus and devices on it
[media] V4L: soc-camera: un-export the soc-camera bus
[media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
[media] V4L: add media bus configuration subdev operations
[media] V4L: soc-camera: group struct field initialisations together
[media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
[media] V4L: pxa-camera: switch to using standard PM hooks
[media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
[media] Don't OOPS if videobuf_dvb_get_frontend return NULL
[media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
[media] omap3isp: Support configurable HS/VS polarities
...
Fix up conflicts:
- arch/arm/mach-omap2/board-rx51-peripherals.c:
cleanup regulator supply definitions in mach-omap2
vs
OMAP3: RX-51: define vdds_csib regulator supply
- drivers/staging/tm6000/tm6000-alsa.c (trivial)
Add control definitions and documentation for controls
specific to codec devices.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add fourcc definitions and documentation for the following
compressed formats: H264, H264 without start codes,
MPEG1/2/4 ES, XVID, VC1 Annex G and Annex L compliant.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[mchehab@redhat.com: Fix a merge conflict and make compat.xml coherent with v4l2.xml]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, -EINVAL is used to return either when an IOCTL is not
implemented, or if the ioctl was not implemented.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move generic stuff into gen-errors.xml, and remove them from
DVB API. While here, removes two bogus error codes that aren't
supported or used on Linux: EINTERNAL and ENOSIGNAL.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove generic errors from ioctl() descriptions. For other ioctl's,
there's no generic section. So, just keep whatever is there.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove generic errors from ioctl() descriptions. For other ioctl's,
there's no generic section. So, just keep whatever is there.
Also remove the EINTERNAL error code, as no DVB driver returns
it, and this error code is not defined on POSIX or on Linux.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Just like the V4L, MC and LIRC API's, point to the generic error
chapter for ioctl's. This will allow moving generic error codes
to just one place inside all media API's.
A latter patch will remove the generic errors from each specific
ioctl.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a reference for the generic error code chapter to LIRC ioctl
description.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L ioctl function descripton also has a generic error chapter.
Remove it, as it is now obsoleted by a general, multi-API generic
error descriptions.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The EBUSY is already described as a generic error condition, with a
similar text.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of having their own generic error codes at the MC API, move
its section to the generic one and be sure that all media ioctl's
will point to it.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Be sure that all VIDIOC_* ioctl are using the return error macro, and
aren't specifying generic error codes internally.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several errors reported by V4L that aren't described.
They can occur on almost all ioctl's. Instead of adding them
into each ioctl, create a new chapter.
For V4L, the new chapter will automatically be listed on all
places, as there's a macro used everywhere there.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Normally no control events will go to the filehandle that called the
VIDIOC_S_CTRL/VIDIOC_S_EXT_CTRLS ioctls. This is to prevent a feedback
loop.
This can now be overridden by setting the new V4L2_EVENT_SUB_FL_ALLOW_FEEDBACK
flag.
Based on suggestions from Mauro Carvalho Chehab <mchehab@redhat.com> and
Laurent Pinchart <laurent.pinchart@ideasonboard.com>.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Starting with v3.1 the V4L2 API provides certain guarantees with respect to
events. Document these.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The old V4L1 Kernel copatibility layer was removed, but the API
spec still says that it is there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patch utility doesn't work with non-binary files. This causes some
tools to break, like generating tarball targets and the scripts that
generate diff patches at http://www.kernel.org/pub/linux/kernel/v2.6/.
So, let's convert all binaries to ascii using base64, and add a
logic at Makefile to convert them back into binaries at runtime.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While here, remove the mediaindexdocs from PHONY.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, all data structures are commented. A few ioctls remain undocumented:
Error: no ID for constraint linkend: VIDEO_GET_SIZE.
Error: no ID for constraint linkend: VIDEO_GET_FRAME_RATE.
Error: no ID for constraint linkend: VIDEO_GET_PTS.
Error: no ID for constraint linkend: VIDEO_GET_FRAME_COUNT.
Error: no ID for constraint linkend: VIDEO_COMMAND.
Error: no ID for constraint linkend: VIDEO_TRY_COMMAND.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The av7110 uses an OSD API. Such API is not documented at all. Also,
the osd.h API uses camelCase and some other weird stuff. Also, dvb-core
doesn't recognize it.
I don't see any good reason why we should document it. It seems better
to just let it as-is. If ever needed, it is probably better to write
a different API for dvb-core.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's no documentation at all for the DVB net API. Still, better to
remove a few warnings about the missing symbols. So, add the net data
structure inside the net.xml. Now, only the ioctl documentation is missed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Still, there are a few ioctl's not documented:
Error: no ID for constraint linkend: DMX_GET_PES_PIDS.
Error: no ID for constraint linkend: DMX_GET_CAPS.
Error: no ID for constraint linkend: DMX_SET_SOURCE.
Error: no ID for constraint linkend: DMX_ADD_PID.
Error: no ID for constraint linkend: DMX_REMOVE_PID.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make the reference links at dmx.h.xml to match the ones at demux.xml.
While here, also syncronizes the structures defined inside the API,
in order to match the current API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure that both ca.h.xml and ca.xml will match the same names for
the sections/links.
This way, it is now possible to identify API spec gaps:
Error: no ID for constraint linkend: ca-pid.
Error: no ID for constraint linkend: ca-pid.
Error: no ID for constraint linkend: CA_RESET.
Error: no ID for constraint linkend: CA_GET_CAP.
Error: no ID for constraint linkend: CA_GET_SLOT_INFO.
Error: no ID for constraint linkend: CA_GET_DESCR_INFO.
Error: no ID for constraint linkend: CA_GET_MSG.
Error: no ID for constraint linkend: CA_SEND_MSG.
Error: no ID for constraint linkend: CA_SET_DESCR.
Error: no ID for constraint linkend: CA_SET_PID.
Basically, in this case, no CA ioctl is described at the specs, and one
file structure (ca-pid) is missing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Although this ioctl is only used at the av7110 driver, it is not
described at the API docbook. Yet, AUDIO_PAUSE ioctl description
somewhat describes it. Fill the gap by using the information there
and by looking inside av7110 implementation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some attributes suffered some changes since DVBv1. Sync them with the
current API header files.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure that both audio.h.xml and audio.xml will match the same names.
This way, it is now possible to identify API spec gaps:
Error: no ID for constraint linkend: AUDIO_CONTINUE.
Error: no ID for constraint linkend: AUDIO_GET_PTS.
Error: no ID for constraint linkend: AUDIO_BILINGUAL_CHANNEL_SELECT.
While here, fix the cut-and-paste description error on AUDIO_SET_KARAOKE.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the remaining:
Error: no ID for constraint linkend:
With this patch, the dvb frontend API matches the current
dvb core implementation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of repeating duplicate parameters to each delivery system,
just add a section for each specific delivery system, showing
what's applicable to each case. This helps userspace app developers
to know what DVB parameters are applicable to each delivery system.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The old way of setting delivery system parameters were to use
an union with specific per-system parameters. However, as newer
delivery systems required more data, the structure size weren't
enough to fit. So, recomend using the DVBS2API instead.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Put the parameters at the sequencial order as they appear inside
the frontend.h header.
TODO: fix the per-standard section, to reflect the parameters
that should actually be used for each transmission system type.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There were lots of DVB S2API parameters that were never documented.
Let's add a definition for all of them, based on what's currently
used inside the core and the drivers.
The description here is not complete nor perfect, so patches
improving it are welcome.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The frontend.h.xml now references to the main document. However,
several references are missed.
Links the trivial ones with the corresponding API descriptions.
While here, updates the main API to reflect the API improvements.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the DVB API provides two ways to specify the delivery
systems, correlate both ways into a table.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The fe_type_t documentation was incomplete and not linked to the
dvb/frontend.h.xml. Properly document it.
Also, drop a note that newer formats are only supported via
FE_GET_PROPERTY/FE_GET_SET_PROPERTY ioctls.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With this change, it is now possible to discover the gap between
the API defined inside include/dvb/frontend.h and the one documented
into the specs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The JPG-Light, AKA Pegasus Lossless JPEG, is used in Divio webcams based
on NW 800/801/802 chips.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
VIDIOC_S_CTRL and VIDIOC_S_EXT_CTRLS return EACCES when setting a read-only
control VIDIOC_TRY_EXT_CTRLS when trying a read-only control and
VIDIOC_G_CTRL and VIDIOC_G_EXT_CTRLS when getting a write-only control.
Document this.
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch addresses several issues pointed by Randy Dunlap
<rdunlap@xenotime.net> at changeset ece722c:
- In the generated index.html file, "media" is listed first, but it
should be listed in alphabetical order, not first.
- The generated files are (hidden) in .tmpmedia/
- The link from the top-level index.html file to "media" is to
media/index.html, but the file is actually in .tmpmedia/media/index.html
- Please build docs with and without using "O=builddir" and test that.
- Would it be possible for media to have its own Makefile instead of
merging into this one?
Due to the way cleandocs target works, I had to rename the media DocBook
to media_api, otherwise cleandocs would remove the /media directory.
Thanks-to: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Sylwester Nawrocki