In case of UDP traffic with datagram length
below MTU this give about 2% performance increase
when tunneling over ipv4 and about 60% when tunneling
over ipv6
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Suggested-and-acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of UDP traffic with datagram length
below MTU this give about 3% performance increase
when tunneling over ipv4 and about 70% when
tunneling over ipv6.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Suggested-and-acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current ip_tunnel cache implementation is prone to a race
that will cause the wrong dst to be cached on cuncurrent dst cache
miss and ip tunnel update via netlink.
Replacing with the generic implementation fix the issue.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Suggested-and-acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also fix a potential race into the existing tunnel code, which
could lead to the wrong dst to be permanenty cached:
CPU1: CPU2:
<xmit on ip6_tunnel>
<cache lookup fails>
dst = ip6_route_output(...)
<tunnel params are changed via nl>
dst_cache_reset() // no effect,
// the cache is empty
dst_cache_set() // the wrong dst
// is permanenty stored
// into the cache
With the new dst implementation the above race is not possible
since the first cache lookup after dst_cache_reset will fail due
to the timestamp check
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Suggested-and-acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add a generic, lockless dst cache implementation.
The need for lock is avoided updating the dst cache fields
only in per cpu scope, and requiring that the cache manipulation
functions are invoked with the local bh disabled.
The refresh_ts and reset_ts fields are used to ensure the cache
consistency in case of cuncurrent cache update (dst_cache_set*) and
reset operation (dst_cache_reset).
Consider the following scenario:
CPU1: CPU2:
<cache lookup with emtpy cache: it fails>
<get dst via uncached route lookup>
<related configuration changes>
dst_cache_reset()
dst_cache_set()
The dst entry set passed to dst_cache_set() should not be used
for later dst cache lookup, because it's obtained using old
configuration values.
Since the refresh_ts is updated only on dst_cache lookup, the
cached value in the above scenario will be discarded on the next
lookup.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Suggested-and-acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All users now pass false, so we can remove it, and remove the code that
was conditional upon it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only protocol affected at present is Geneve.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was initially introduced in df2cf4a78e ("IGMP: Inhibit
reports for local multicast groups") by defining the sysctl in the
ipv4_net_table array, however it was never implemented to be
namespace aware. Fix this by changing the code accordingly.
Signed-off-by: David S. Miller <davem@davemloft.net>
This change extends the fast SO_REUSEPORT socket lookup implemented
for UDP to TCP. Listener sockets with SO_REUSEPORT and the same
receive address are additionally added to an array for faster
random access. This means that only a single socket from the group
must be found in the listener list before any socket in the group can
be used to receive a packet. Previously, every socket in the group
needed to be considered before handing off the incoming packet.
This feature also exposes the ability to use a BPF program when
selecting a socket from a reuseport group.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preliminary step to allow fast socket lookup of SO_REUSEPORT
groups. Doing so with a BPF filter will require access to the
skb in question. This change plumbs the skb (and offset to payload
data) through the call stack to the listening socket lookup
implementations where it will be used in a following patch.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support fast lookups for TCP sockets with SO_REUSEPORT,
the function that adds sockets to the listening hash set needs
to be able to check receive address equality. Since this equality
check is different for IPv4 and IPv6, we will need two different
socket hashing functions.
This patch adds inet6_hash identical to the existing inet_hash function
and updates the appropriate references. A following patch will
differentiate the two by passing different comparison functions to
__inet_hash.
Additionally, in order to use the IPv6 address equality function from
inet6_hashtables (which is compiled as a built-in object when IPv6 is
enabled) it also needs to be in a built-in object file as well. This
moves ipv6_rcv_saddr_equal into inet_hashtables to accomplish this.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support fast reuseport lookups in TCP, the hash function
defined in struct proto must be capable of returning an error code.
This patch changes the function signature of all related hash functions
to return an integer and handles or propagates this return value at
all call sites.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to 4.3, openvswitch tunnel vports (vxlan, gre and geneve) could
transmit vxlan packets of any size, constrained only by the ability to
send out the resulting packets. 4.3 introduced netdevs corresponding
to tunnel vports. These netdevs have an MTU, which limits the size of
a packet that can be successfully encapsulated. The default MTU
values are low (1500 or less), which is awkwardly small in the context
of physical networks supporting jumbo frames, and leads to a
conspicuous change in behaviour for userspace.
Instead, set the MTU on openvswitch-created netdevs to be the relevant
maximum (i.e. the maximum IP packet size minus any relevant overhead),
effectively restoring the behaviour prior to 4.3.
Signed-off-by: David Wragg <david@weave.works>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the bonding allows to set ad_actor_system and prio while the
bond device is down, but these are actually applied only if there aren't
any slaves yet (applied to bond device when first slave shows up, and to
slaves at 3ad bind time). After this patch changes are applied immediately
and the new values can be used/seen after the bond's upped so it's not
necessary anymore to release all and enslave again to see the changes.
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Novopashenniy reported that ICMP redirects on SYN_RECV sockets
were leading to RST.
This is of course incorrect.
A specific list of ICMP messages should be able to drop a SYN_RECV.
For instance, a REDIRECT on SYN_RECV shall be ignored, as we do
not hold a dst per SYN_RECV pseudo request.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111751
Fixes: 079096f103 ("tcp/dccp: install syn_recv requests into ehash table")
Reported-by: Petr Novopashenniy <pety@rusnet.ru>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit referenced in the Fixes tag incorrectly accounted the number
of in-flight fds over a unix domain socket to the original opener
of the file-descriptor. This allows another process to arbitrary
deplete the original file-openers resource limit for the maximum of
open files. Instead the sending processes and its struct cred should
be credited.
To do so, we add a reference counted struct user_struct pointer to the
scm_fp_list and use it to account for the number of inflight unix fds.
Fixes: 712f4aad40 ("unix: properly account for FDs passed over unix sockets")
Reported-by: David Herrmann <dh.herrmann@gmail.com>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
RCO and GBP are VXLAN extensions, not specified in RFC 7348. Because of
that, they need to be explicitly enabled when creating vxlan interface. By
default, those extensions are not used and plain VXLAN header is sent and
received.
Reflect this in vxlan.h: first, the plain VXLAN header is defined. Following
it, RCO is documented and defined, and likewise for GBP.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VNI_HASH_BITS and VNI_HASH_SIZE are defined twice. Remove the extra
definitions.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
include/net/vxlan.h is a kernel header, no need to prefix fixed size types
with double underscore.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we acknowledge a FIN, it is not enough to ack the sequence number
and queue the skb into receive queue. We also have to call tcp_fin()
to properly update socket state and send proper poll() notifications.
It seems we also had the problem if we received a SYN packet with the
FIN flag set, but it does not seem an urgent issue, as no known
implementation can do that.
Fixes: 61d2bcae99 ("tcp: fastopen: accept data/FIN present in SYNACK message")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 7413 (TCP Fast Open) 4.2.2 states that the SYNACK message
MAY include data and/or FIN
This patch adds support for the client side :
If we receive a SYNACK with payload or FIN, queue the skb instead
of ignoring it.
Since we already support the same for SYN, we refactor the existing
code and reuse it. Note we need to clone the skb, so this operation
might fail under memory pressure.
Sara Dickinson pointed out FreeBSD server Fast Open implementation
was planned to generate such SYNACK in the future.
The server side might be implemented on linux later.
Reported-by: Sara Dickinson <sara@sinodun.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"This looks like a lot but it's a mixture of regression fixes as well
as fixes for longer standing issues.
1) Fix on-channel cancellation in mac80211, from Johannes Berg.
2) Handle CHECKSUM_COMPLETE properly in xt_TCPMSS netfilter xtables
module, from Eric Dumazet.
3) Avoid infinite loop in UDP SO_REUSEPORT logic, also from Eric
Dumazet.
4) Avoid a NULL deref if we try to set SO_REUSEPORT after a socket is
bound, from Craig Gallek.
5) GRO key comparisons don't take lightweight tunnels into account,
from Jesse Gross.
6) Fix struct pid leak via SCM credentials in AF_UNIX, from Eric
Dumazet.
7) We need to set the rtnl_link_ops of ipv6 SIT tunnels before we
register them, otherwise the NEWLINK netlink message is missing
the proper attributes. From Thadeu Lima de Souza Cascardo.
8) Several Spectrum chip bug fixes for mlxsw switch driver, from Ido
Schimmel
9) Handle fragments properly in ipv4 easly socket demux, from Eric
Dumazet.
10) Don't ignore the ifindex key specifier on ipv6 output route
lookups, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (128 commits)
tcp: avoid cwnd undo after receiving ECN
irda: fix a potential use-after-free in ircomm_param_request
net: tg3: avoid uninitialized variable warning
net: nb8800: avoid uninitialized variable warning
net: vxge: avoid unused function warnings
net: bgmac: clarify CONFIG_BCMA dependency
net: hp100: remove unnecessary #ifdefs
net: davinci_cpdma: use dma_addr_t for DMA address
ipv6/udp: use sticky pktinfo egress ifindex on connect()
ipv6: enforce flowi6_oif usage in ip6_dst_lookup_tail()
netlink: not trim skb for mmaped socket when dump
vxlan: fix a out of bounds access in __vxlan_find_mac
net: dsa: mv88e6xxx: fix port VLAN maps
fib_trie: Fix shift by 32 in fib_table_lookup
net: moxart: use correct accessors for DMA memory
ipv4: ipconfig: avoid unused ic_proto_used symbol
bnxt_en: Fix crash in bnxt_free_tx_skbs() during tx timeout.
bnxt_en: Exclude rx_drop_pkts hw counter from the stack's rx_dropped counter.
bnxt_en: Ring free response from close path should use completion ring
net_sched: drr: check for NULL pointer in drr_dequeue
...
Johan Hedberg says:
====================
pull request: bluetooth 2016-01-30
Here's a set of important Bluetooth fixes for the 4.5 kernel:
- Two fixes to 6LoWPAN code (one fixing a potential crash)
- Fix LE pairing with devices using both public and random addresses
- Fix allocation of dynamic LE PSM values
- Fix missing COMPATIBLE_IOCTL for UART line discipline
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of ip6_dst_lookup_tail basically
ignore the egress ifindex match: if the saddr is set,
ip6_route_output() purposefully ignores flowi6_oif, due
to the commit d46a9d678e ("net: ipv6: Dont add RT6_LOOKUP_F_IFACE
flag if saddr set"), if the saddr is 'any' the first route lookup
in ip6_dst_lookup_tail fails, but upon failure a second lookup will
be performed with saddr set, thus ignoring the ifindex constraint.
This commit adds an output route lookup function variant, which
allows the caller to specify lookup flags, and modify
ip6_dst_lookup_tail() to enforce the ifindex match on the second
lookup via said helper.
ip6_route_output() becames now a static inline function build on
top of ip6_route_output_flags(); as a side effect, out-of-tree
modules need now a GPL license to access the output route lookup
functionality.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since cfg80211 frequently takes actions from its netdev notifier
call, wireless extensions messages could still be ordered badly
since the wext netdev notifier, since wext is built into the
kernel, runs before the cfg80211 netdev notifier. For example,
the following can happen:
5: wlan1: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default
link/ether 02:00:00:00:01:00 brd ff:ff:ff:ff:ff:ff
5: wlan1: <BROADCAST,MULTICAST,UP>
link/ether
when setting the interface down causes the wext message.
To also fix this, export the wireless_nlevent_flush() function
and also call it from the cfg80211 notifier.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Having proper defines makes the code a bit readable, it also avoids
duplicating hard-coded values since these are also needed when
auto-allocating PSM values (in a subsequent patch).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After we use refcnt to check if transport is alive, the dead can be
removed from sctp_transport.
The traversal of transport_addr_list in procfs dump is using
list_for_each_entry_rcu, no need to check if it has been freed.
sctp_generate_t3_rtx_event and sctp_generate_heartbeat_event is
protected by sock lock, it's not necessary to check dead, either.
also, the timers are cancelled when sctp_transport_free() is
called, that it doesn't wait for refcnt to reach 0 to cancel them.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when __sctp_lookup_association is running in BH, it will try to
check if t->dead is set, but meanwhile other CPUs may be freeing this
transport and this assoc and if it happens that
__sctp_lookup_association checked t->dead a bit too early, it may think
that the association is still good while it was already freed.
So we fix this race by using atomic_add_unless in sctp_transport_hold.
After we get one transport from hashtable, we will hold it only when
this transport's refcnt is not 0, so that we can make sure t->asoc
cannot be freed before we hold the asoc again.
Note that sctp association is not freed using RCU so we can't use
atomic_add_unless() with it as it may just be too late for that either.
Fixes: 4f00878126 ("sctp: apply rhashtable api to send/recv path")
Reported-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces uses of the long obsolete hash interface with
ahash.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: David S. Miller <davem@davemloft.net>
This patch replaces uses of the long obsolete hash interface with
shash.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: David S. Miller <davem@davemloft.net>
The cgroup methods are no longer used after baac50bbc3 ("net:
tcp_memcontrol: simplify linkage between socket and page counter").
The hunk to delete them was included in the original patch but must
have gotten lost during conflict resolution on the way upstream.
Fixes: baac50bbc3 ("net: tcp_memcontrol: simplify linkage between socket and page counter")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO is currently not aware of tunnel metadata generated by lightweight
tunnels and stored in the dst. This leads to two possible problems:
* Incorrectly merging two frames that have different metadata.
* Leaking of allocated metadata from merged frames.
This avoids those problems by comparing the tunnel information before
merging, similar to how we handle other metadata (such as vlan tags),
and releasing any state when we are done.
Reported-by: John <john.phillips5@hpe.com>
Fixes: 2e15ea39 ("ip_gre: Add support to collect tunnel metadata.")
Signed-off-by: Jesse Gross <jesse@kernel.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_memcontrol.c only contains legacy memory.tcp.kmem.* file definitions
and mem_cgroup->tcp_mem init/destroy stuff. This doesn't belong to
network subsys. Let's move it to memcontrol.c. This also allows us to
reuse generic code for handling legacy memcg files.
Signed-off-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This series adds accounting of the historical "kmem" memory consumers to
the cgroup2 memory controller.
These consumers include the dentry cache, the inode cache, kernel stack
pages, and a few others that are pointed out in patch 7/8. The
footprint of these consumers is directly tied to userspace activity in
common workloads, and so they have to be part of the minimally viable
configuration in order to present a complete feature to our users.
The cgroup2 interface of the memory controller is far from complete, but
this series, along with the socket memory accounting series, provides
the final semantic changes for the existing memory knobs in the cgroup2
interface, which is scheduled for initial release in the next merge
window.
This patch (of 8):
Remove unused css argument frmo memcg_init_kmem()
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we need to lock all buckets in the connection hashtable we'd attempt to
lock 1024 spinlocks, which is way more preemption levels than supported by
the kernel. Furthermore, this behavior was hidden by checking if lockdep is
enabled, and if it was - use only 8 buckets(!).
Fix this by using a global lock and synchronize all buckets on it when we
need to lock them all. This is pretty heavyweight, but is only done when we
need to resize the hashtable, and that doesn't happen often enough (or at all).
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Marc Dionne discovered a NULL pointer dereference when setting
SO_REUSEPORT on a socket after it is bound.
This patch removes the assumption that at least one socket in the
reuseport group is bound with the SO_REUSEPORT option before other
bind calls occur.
Fixes: e32ea7e747 ("soreuseport: fast reuseport UDP socket selection")
Reported-by: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: Craig Gallek <kraig@google.com>
Tested-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In file included from net/ipv4/tcp_ipv4.c:77 (and many more):
include/net/tcp_memcontrol.h:5: warning: ‘struct cgroup_subsys’ declared inside parameter list
include/net/tcp_memcontrol.h:5: warning: its scope is only this definition or declaration, which is probably not what you want
Add forward declarations for all used structures to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"A quick set of bug fixes after there initial networking merge:
1) Netlink multicast group storage allocator only was tested with
nr_groups equal to 1, make it work for other values too. From
Matti Vaittinen.
2) Check build_skb() return value in macb and hip04_eth drivers, from
Weidong Wang.
3) Don't leak x25_asy on x25_asy_open() failure.
4) More DMA map/unmap fixes in 3c59x from Neil Horman.
5) Don't clobber IP skb control block during GSO segmentation, from
Konstantin Khlebnikov.
6) ECN helpers for ipv6 don't fixup the checksum, from Eric Dumazet.
7) Fix SKB segment utilization estimation in xen-netback, from David
Vrabel.
8) Fix lockdep splat in bridge addrlist handling, from Nikolay
Aleksandrov"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
bgmac: Fix reversed test of build_skb() return value.
bridge: fix lockdep addr_list_lock false positive splat
net: smsc: Add support h8300
xen-netback: free queues after freeing the net device
xen-netback: delete NAPI instance when queue fails to initialize
xen-netback: use skb to determine number of required guest Rx requests
net: sctp: Move sequence start handling into sctp_transport_get_idx()
ipv6: update skb->csum when CE mark is propagated
net: phy: turn carrier off on phy attach
net: macb: clear interrupts when disabling them
sctp: support to lookup with ep+paddr in transport rhashtable
net: hns: fixes no syscon error when init mdio
dts: hisi: fixes no syscon fault when init mdio
net: preserve IP control block during GSO segmentation
fsl/fman: Delete one function call "put_device" in dtsec_config()
hip04_eth: fix missing error handle for build_skb failed
3c59x: fix another page map/single unmap imbalance
3c59x: balance page maps and unmaps
x25_asy: Free x25_asy on x25_asy_open() failure.
mlxsw: fix SWITCHDEV_OBJ_ID_PORT_MDB
...
When a tunnel decapsulates the outer header, it has to comply
with RFC 6080 and eventually propagate CE mark into inner header.
It turns out IP6_ECN_set_ce() does not correctly update skb->csum
for CHECKSUM_COMPLETE packets, triggering infamous "hw csum failure"
messages and stack traces.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unified hierarchy memory controller is going to use this jump label
as well to control the networking callbacks. Move it to the memory
controller code and give it a more generic name.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There won't be any separate counters for socket memory consumed by
protocols other than TCP in the future. Remove the indirection and link
sockets directly to their owning memory cgroup.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There won't be a tcp control soft limit, so integrating the memcg code
into the global skmem limiting scheme complicates things unnecessarily.
Replace this with simple and clear charge and uncharge calls--hidden
behind a jump label--to account skb memory.
Note that this is not purely aesthetic: as a result of shoehorning the
per-memcg code into the same memory accounting functions that handle the
global level, the old code would compare the per-memcg consumption
against the smaller of the per-memcg limit and the global limit. This
allowed the total consumption of multiple sockets to exceed the global
limit, as long as the individual sockets stayed within bounds. After
this change, the code will always compare the per-memcg consumption to
the per-memcg limit, and the global consumption to the global limit, and
thus close this loophole.
Without a soft limit, the per-memcg memory pressure state in sockets is
generally questionable. However, we did it until now, so we continue to
enter it when the hard limit is hit, and packets are dropped, to let
other sockets in the cgroup know that they shouldn't grow their transmit
windows, either. However, keep it simple in the new callback model and
leave memory pressure lazily when the next packet is accepted (as
opposed to doing it synchroneously when packets are processed). When
packets are dropped, network performance will already be in the toilet,
so that should be a reasonable trade-off.
As described above, consumption is now checked on the per-memcg level
and the global level separately. Likewise, memory pressure states are
maintained on both the per-memcg level and the global level, and a
socket is considered under pressure when either level asserts as much.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
tcp_memcontrol replicates the global sysctl_mem limit array per cgroup,
but it only ever sets these entries to the value of the memory_allocated
page_counter limit. Use the latter directly.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The number of allocated sockets is used for calculations in the soft
limit phase, where packets are accepted but the socket is under memory
pressure.
Since there is no soft limit phase in tcp_memcontrol, and memory
pressure is only entered when packets are already dropped, this is
actually dead code. Remove it.
As this is the last user of parent_cg_proto(), remove that too.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a cgroup currently breaches its socket memory limit, it enters
memory pressure mode for itself and its *ancestors*. This throttles
transmission in unrelated sibling and cousin subtrees that have nothing
to do with the breached limit.
On the contrary, breaching a limit should make that group and its
*children* enter memory pressure mode. But this happens already, albeit
lazily: if an ancestor limit is breached, siblings will enter memory
pressure on their own once the next packet arrives for them.
So no additional hierarchy code is needed. Remove the bogus stuff.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When charging socket memory, the code currently checks only the local
page counter for excess to determine whether the memcg is under socket
pressure. But even if the local counter is fine, one of the ancestors
could have breached its limit, which should also force this child to
enter socket pressure. This currently doesn't happen.
Fix this by using page_counter_try_charge() first. If that fails, it
means that either the local counter or one of the ancestors are in
excess of their limit, and the child should enter socket pressure.
Fixes: 3e32cb2e0a ("mm: memcontrol: lockless page counters")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently mac80211 does not inform the driver of the session
block ack timeout when starting a rx aggregation session.
Drivers that manage the reorder buffer need to know this
parameter.
Seeing that there are now too many arguments for the
drv_ampdu_action() function, wrap them inside a structure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It's not always necessary to set the status.freq field, for example
when this would be an expensive calculation. It must be set for all
management frames (as they might be reported to userspace), but for
data frames it's not really required. Document this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently mac80211 does not inform the driver of the window
size when starting an RX aggregation session.
To enable managing the reorder buffer in the driver or hardware
the window size is needed.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an option for driver to check for packet duplication
by itself.
This is needed for example by the iwlwifi driver which
parallelizes the RX path and does the duplication check
per queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The Group ID Management frame is an Action frame of
category VHT. It is transmitted by the AP to assign
or change the user position of a STA for one or more
group IDs.
Process and save the group membership data. Notify
underlying driver of changes.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/bonding/bond_main.c
drivers/net/ethernet/mellanox/mlxsw/spectrum.h
drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
The bond_main.c and mellanox switch conflicts were cases of
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a skb_at_tc_ingress() as this will be needed elsewhere as well and
can hide the ugly ifdef.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the final part required to namespaceify the tcp
keep alive mechanism.
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is required to have full tcp keepalive mechanism namespace
support.
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different net namespaces might have different requirements as to
the keepalive time of tcp sockets. This might be required in cases
where different firewall rules are in place which require tcp
timeout sockets to be increased/decreased independently of the host.
Signed-off-by: Nikolay Borisov <kernel@kyup.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udp tunnel offloads tend to aggregate datagrams based on inner
headers. gro engine gets notified by tunnel implementations about
possible offloads. The match is solely based on the port number.
Imagine a tunnel bound to port 53, the offloading will look into all
DNS packets and tries to aggregate them based on the inner data found
within. This could lead to data corruption and malformed DNS packets.
While this patch minimizes the problem and helps an administrator to find
the issue by querying ip tunnel/fou, a better way would be to match on
the specific destination ip address so if a user space socket is bound
to the same address it will conflict.
Cc: Tom Herbert <tom@herbertland.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define HW multicast entry: MAC and VID.
Using a MAC address simplifies support for both IPV4 and IPv6.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_multipath_hash() computes a hash using __be32 values, force
cast these to u32 to pacify sparse.
Signed-off-by: Lance Richardson <lrichard@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next, they are:
1) Release nf_tables objects on netns destructions via
nft_release_afinfo().
2) Destroy basechain and rules on netdevice removal in the new netdev
family.
3) Get rid of defensive check against removal of inactive objects in
nf_tables.
4) Pass down netns pointer to our existing nfnetlink callbacks, as well
as commit() and abort() nfnetlink callbacks.
5) Allow to invert limit expression in nf_tables, so we can throttle
overlimit traffic.
6) Add packet duplication for the netdev family.
7) Add forward expression for the netdev family.
8) Define pr_fmt() in conntrack helpers.
9) Don't leave nfqueue configuration on inconsistent state in case of
errors, from Ken-ichirou MATSUZAWA, follow up patches are also from
him.
10) Skip queue option handling after unbind.
11) Return error on unknown both in nfqueue and nflog command.
12) Autoload ctnetlink when NFQA_CFG_F_CONNTRACK is set.
13) Add new NFTA_SET_USERDATA attribute to store user data in sets,
from Carlos Falgueras.
14) Add support for 64 bit byteordering changes nf_tables, from Florian
Westphal.
15) Add conntrack byte/packet counter matching support to nf_tables,
also from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2016-01-08
Here's one more bluetooth-next pull request for the 4.5 kernel:
- Support for CRC check and promiscuous mode for CC2520
- Fixes to btmrvl driver
- New ACPI IDs for hci_bcm driver
- Limited Discovery support for the Bluetooth mgmt interface
- Minor other cleanups here and there
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
User data is stored at after 'nft_set_ops' private data into 'data[]'
flexible array. The field 'udata' points to user data and 'udlen' stores
its length.
Add new flag NFTA_SET_USERDATA.
Signed-off-by: Carlos Falgueras García <carlosfg@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Adding vlan_filtering attribute to allow hardware vendor to support
vlan-aware bridges. Vlan_filtering is a per-bridge attribute.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only user was removed in commit
029f7f3b87 ("netfilter: ipv6: nf_defrag: avoid/free clone operations").
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
transport hashtable will replace the association hashtable,
so association hashtable is not used in sctp any more, so
drop the codes about that.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tranport hashtbale will replace the association hashtable to do the
lookup for transport, and then get association by t->assoc, rhashtable
apis will be used because of it's resizable, scalable and using rcu.
lport + rport + paddr will be the base hashkey to locate the chain,
with net to protect one netns from another, then plus the laddr to
compare to get the target.
this patch will provider the lookup functions:
- sctp_epaddr_lookup_transport
- sctp_addrs_lookup_transport
hash/unhash functions:
- sctp_hash_transport
- sctp_unhash_transport
init/destroy functions:
- sctp_transport_hashtable_init
- sctp_transport_hashtable_destroy
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the mgmt Start Limited Discovery command. Most
of existing Start Discovery code is reused since the only difference
is the presence of a 'limited' flag as part of the discovery state.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To make the EIR parsing helper more general purpose, make it return
the found data and its length rather than just saying whether the data
was present or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commands run in a vrf context are not failing as expected on a route lookup:
root@kenny:~# ip ro ls table vrf-red
unreachable default
root@kenny:~# ping -I vrf-red -c1 -w1 10.100.1.254
ping: Warning: source address might be selected on device other than vrf-red.
PING 10.100.1.254 (10.100.1.254) from 0.0.0.0 vrf-red: 56(84) bytes of data.
--- 10.100.1.254 ping statistics ---
2 packets transmitted, 0 received, 100% packet loss, time 999ms
Since the vrf table does not have a route for 10.100.1.254 the ping
should have failed. The saddr lookup causes a full VRF table lookup.
Propogating a lookup failure to the user allows the command to fail as
expected:
root@kenny:~# ping -I vrf-red -c1 -w1 10.100.1.254
connect: No route to host
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose socket options for setting a classic or extended BPF program
for use when selecting sockets in an SO_REUSEPORT group. These options
can be used on the first socket to belong to a group before bind or
on any socket in the group after bind.
This change includes refactoring of the existing sk_filter code to
allow reuse of the existing BPF filter validation checks.
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include a struct sock_reuseport instance when a UDP socket binds to
a specific address for the first time with the reuseport flag set.
When selecting a socket for an incoming UDP packet, use the information
available in sock_reuseport if present.
This required adding an additional field to the UDP source address
equality function to differentiate between exact and wildcard matches.
The original use case allowed wildcard matches when checking for
existing port uses during bind. The new use case of adding a socket
to a reuseport group requires exact address matching.
Performance test (using a machine with 2 CPU sockets and a total of
48 cores): Create reuseport groups of varying size. Use one socket
from this group per user thread (pinning each thread to a different
core) calling recvmmsg in a tight loop. Record number of messages
received per second while saturating a 10G link.
10 sockets: 18% increase (~2.8M -> 3.3M pkts/s)
20 sockets: 14% increase (~2.9M -> 3.3M pkts/s)
40 sockets: 13% increase (~3.0M -> 3.4M pkts/s)
This work is based off a similar implementation written by
Ying Cai <ycai@google.com> for implementing policy-based reuseport
selection.
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct sock_reuseport is an optional shared structure referenced by each
socket belonging to a reuseport group. When a socket is bound to an
address/port not yet in use and the reuseport flag has been set, the
structure will be allocated and attached to the newly bound socket.
When subsequent calls to bind are made for the same address/port, the
shared structure will be updated to include the new socket and the
newly bound socket will reference the group structure.
Usually, when an incoming packet was destined for a reuseport group,
all sockets in the same group needed to be considered before a
dispatching decision was made. With this structure, an appropriate
socket can be found after looking up just one socket in the group.
This shared structure will also allow for more complicated decisions to
be made when selecting a socket (eg a BPF filter).
This work is based off a similar implementation written by
Ying Cai <ycai@google.com> for implementing policy-based reuseport
selection.
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving the caller of iptunnel_xmit_stats causes a build error in
randconfig builds that disable CONFIG_INET:
In file included from ../net/xfrm/xfrm_input.c:17:0:
../include/net/ip6_tunnel.h: In function 'ip6tunnel_xmit':
../include/net/ip6_tunnel.h:93:2: error: implicit declaration of function 'iptunnel_xmit_stats' [-Werror=implicit-function-declaration]
iptunnel_xmit_stats(dev, pkt_len);
The reason is that the iptunnel_xmit_stats definition is hidden
inside #ifdef CONFIG_INET but the caller is not. We can change
one or the other to fix it, and this patch adds a second #ifdef
around ip6tunnel_xmit() to avoid seeing the invalid call.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 039f50629b ("ip_tunnel: Move stats update to iptunnel_xmit()")
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the first NFC pull request for 4.5 and it brings:
- A new driver for the STMicroelectronics ST95HF NFC chipset.
The ST95HF is an NFC digital transceiver with an embedded analog
front-end and as such relies on the Linux NFC digital
implementation. This is the 3rd user of the NFC digital stack.
- ACPI support for the ST st-nci and st21nfca drivers.
- A small improvement for the nfcsim driver, as we can now tune
the Rx delay through sysfs.
- A bunch of minor cleanups and small fixes from Christophe Ricard,
for a few drivers and the NFC core code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWgsv0AAoJEIqAPN1PVmxKvukP/3eJwA+chAUF89/fqwqFTaJN
fffLoOxx2OBIbTXD2VV36yw4bAo9tbKDAYBZiot3Ig7Kg0SeCJ5oPA9xCVnWPrEY
hxFAldvl+lWQs8nrUOgUZItiFBeUPdfW9YX/yKhUZVc+602nUG/e/+6x8B5MhIce
SAfgCyd0c16DApltP7sw1muyZMvsO6Ow6dyNzDUVYZuabvEhe3SLSj9KFJi7Thsp
h41Iv+bwPLhwF4RXGA6rei/gdEDSMRohprdj3uTDiTarGW+OpcAO0zWACS5m4eR0
zF19+HjGPUk/LpFRaU31xX0ZQQjOTmmfsOt4FBb3P7oJx47egycsadLYPexeG7nj
ruyS6ezlRX1I/tZsnyLNJK92mK5TXYLz2uJ8r2ii/BgPNE+AErB3zKCC+EjXzWhh
AvClGu5b88WJLxoq3I3l5evPwGhebGZ8N/1uiFsHOxvzKVLgxwOmNLRGN4XXxB2i
UbIHgBb6smsu/l+3q9R83kfoMaoWnr+OUIi2QPQVDt/K7t1LfsCuIhzcGSgo1VuW
fGlA1iu+CNDknofeCl4JDo2UXAETO4gdKWw87GXeUcbbraLUczZeO7FFLZqxbMYc
OCaPYshmVFeZRypYdRWDHw67ivj0/h+9iq4PP1XOROkRFH746dD/p4yamJwVi20B
samZ8VPwzgH3/ohQJyX3
=VFUH
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz says:
====================
NFC 4.5 pull request
This is the first NFC pull request for 4.5 and it brings:
- A new driver for the STMicroelectronics ST95HF NFC chipset.
The ST95HF is an NFC digital transceiver with an embedded analog
front-end and as such relies on the Linux NFC digital
implementation. This is the 3rd user of the NFC digital stack.
- ACPI support for the ST st-nci and st21nfca drivers.
- A small improvement for the nfcsim driver, as we can now tune
the Rx delay through sysfs.
- A bunch of minor cleanups and small fixes from Christophe Ricard,
for a few drivers and the NFC core code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ieee802154_llsec_ops structure is never modified, so declare it as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
You can use this to duplicate packets and inject them at the egress path
of the specified interface. This duplication allows you to inspect
traffic from the dummy or any other interface dedicated to this purpose.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add support for missing HCI event EVT_CONNECTIVITY and forward
it to userspace.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
If the netdevice is destroyed, the resources that are attached should
be released too as they belong to the device that is now gone.
Suggested-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We have to release the existing objects on netns removal otherwise we
leak them. Chains are unregistered in first place to make sure no
packets are walking on our rules and sets anymore.
The object release happens by when we unregister the family via
nft_release_afinfo() which is called from nft_unregister_afinfo() from
the corresponding __net_exit path in every family.
Reported-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
By moving stats update into iptunnel_xmit(), we can simplify
iptunnel_xmit() usage. With this change there is no need to
call another function (iptunnel_xmit_stats()) to update stats
in tunnel xmit code path.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoids cluttering tcp_v4_send_reset when followup patch extends
it to deal with timewait sockets.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains the first batch of Netfilter updates for
the upcoming 4.5 kernel. This batch contains userspace netfilter header
compilation fixes, support for packet mangling in nf_tables, the new
tracing infrastructure for nf_tables and cgroup2 support for iptables.
More specifically, they are:
1) Two patches to include dependencies in our netfilter userspace
headers to resolve compilation problems, from Mikko Rapeli.
2) Four comestic cleanup patches for the ebtables codebase, from Ian Morris.
3) Remove duplicate include in the netfilter reject infrastructure,
from Stephen Hemminger.
4) Two patches to simplify the netfilter defragmentation code for IPv6,
patch from Florian Westphal.
5) Fix root ownership of /proc/net netfilter for unpriviledged net
namespaces, from Philip Whineray.
6) Get rid of unused fields in struct nft_pktinfo, from Florian Westphal.
7) Add mangling support to our nf_tables payload expression, from
Patrick McHardy.
8) Introduce a new netlink-based tracing infrastructure for nf_tables,
from Florian Westphal.
9) Change setter functions in nfnetlink_log to be void, from
Rami Rosen.
10) Add netns support to the cttimeout infrastructure.
11) Add cgroup2 support to iptables, from Tejun Heo.
12) Introduce nfnl_dereference_protected() in nfnetlink, from Florian.
13) Add support for mangling pkttype in the nf_tables meta expression,
also from Florian.
BTW, I need that you pull net into net-next, I have another batch that
requires changes that I don't yet see in net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow accepted sockets to derive their sk_bound_dev_if setting from the
l3mdev domain in which the packets originated. A sysctl setting is added
to control the behavior which is similar to sk_mark and
sysctl_tcp_fwmark_accept.
This effectively allow a process to have a "VRF-global" listen socket,
with child sockets bound to the VRF device in which the packet originated.
A similar behavior can be achieved using sk_mark, but a solution using marks
is incomplete as it does not handle duplicate addresses in different L3
domains/VRFs. Allowing sockets to inherit the sk_bound_dev_if from l3mdev
domain provides a complete solution.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper to lookup l3mdev master index given a device index.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Docbook does not like the definition of macros inside a field declaration
and adds a warning. Move the definition out.
Fixes: 79462ad02e ("net: add validation for the socket syscall protocol argument")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an op that the drivers can call into to get existing
geneve ports.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we all know, the value of pf_retrans >= max_retrans_path can
disable pf state. The variables of pf_retrans and max_retrans_path
can be changed by the userspace application.
Sometimes the user expects to disable pf state while the 2
variables are changed to enable pf state. So it is necessary to
introduce a new variable to disable pf state.
According to the suggestions from Vlad Yasevich, extra1 and extra2
are removed. The initialization of pf_enable is added.
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Zhu Yanjun <zyjzyj2000@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern added a vif field in the a4 part of inetpeer_addr struct.
This broke IPv4 TCP fast open client side and more generally tcp metrics
cache, because inetpeer_addr_cmp() is now comparing two u32 instead of
one.
inetpeer_set_addr_v4() needs to properly init vif field, otherwise
the comparison result depends on uninitialized data.
Fixes: 192132b9a0 ("net: Add support for VRFs to inetpeer cache")
Reported-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements SOCK_DESTROY for TCP sockets. It causes all
blocking calls on the socket to fail fast with ECONNABORTED and
causes a protocol close of the socket. It informs the other end
of the connection by sending a RST, i.e., initiating a TCP ABORT
as per RFC 793. ECONNABORTED was chosen for consistency with
FreeBSD.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a SOCK_DESTROY operation, a destroy function
pointer to sock_diag_handler, and a diag_destroy function
pointer. It does not include any implementation code.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements an ILA tanslation table. This table can be
configured with identifier to locator mappings, and can be be queried
to resolve a mapping. Queries can be parameterized based on interface,
direction (incoming or outoing), and matching locator. The table is
implemented using rhashtable and is configured via netlink (through
"ip ila .." in iproute).
The table may be used as alternative means to do do ILA tanslations
other than the lw tunnels
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The start callback allows the caller to set up a context for the
dump callbacks. Presumably, the context can then be destroyed in
the done callback.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tcp_send_sendpage and tcp_sendmsg we check the route capabilities to
determine if checksum offload can be performed. This check currently
does not take the IP protocol into account for devices that advertise
only one of NETIF_F_IPV6_CSUM or NETIF_F_IP_CSUM. This patch adds a
function to check capabilities for checksum offload with a socket
called sk_check_csum_caps. This function checks for specific IPv4 or
IPv6 offload support based on the family of the socket.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
switchdev drivers need to know the netdev on which the switchdev op was
invoked. For example, the STP state of a VLAN interface configured on top
of a port can change while being member in a bridge. In this case, the
underlying driver should only change the STP state of that particular
VLAN and not of all the VLANs configured on the port.
However, current switchdev infrastructure only passes the port netdev down
to the driver. Solve that by passing the original device down to the
driver as part of the required switchdev object / attribute.
This doesn't entail any change in current switchdev drivers. It simply
enables those supporting stacked devices to know the originating device
and act accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Wilder reported crashes caused by dst reuse.
<quote David>
I am seeing a crash on a distro V4.2.3 kernel caused by a double
release of a dst_entry. In ipv4_dst_destroy() the call to
list_empty() finds a poisoned next pointer, indicating the dst_entry
has already been removed from the list and freed. The crash occurs
18 to 24 hours into a run of a network stress exerciser.
</quote>
Thanks to his detailed report and analysis, we were able to understand
the core issue.
IP early demux can associate a dst to skb, after a lookup in TCP/UDP
sockets.
When socket cache is not properly set, we want to store into
sk->sk_dst_cache the dst for future IP early demux lookups,
by acquiring a stable refcount on the dst.
Problem is this acquisition is simply using an atomic_inc(),
which works well, unless the dst was queued for destruction from
dst_release() noticing dst refcount went to zero, if DST_NOCACHE
was set on dst.
We need to make sure current refcount is not zero before incrementing
it, or risk double free as David reported.
This patch, being a stable candidate, adds two new helpers, and use
them only from IP early demux problematic paths.
It might be possible to merge in net-next skb_dst_force() and
skb_dst_force_safe(), but I prefer having the smallest patch for stable
kernels : Maybe some skb_dst_force() callers do not expect skb->dst
can suddenly be cleared.
Can probably be backported back to linux-3.6 kernels
Reported-by: David J. Wilder <dwilder@us.ibm.com>
Tested-by: David J. Wilder <dwilder@us.ibm.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-12-11
Here's another set of Bluetooth & 802.15.4 patches for the 4.5 kernel:
- 6LoWPAN debugfs support
- New 802.15.4 driver for ADF7242 MAC IEEE802154
- Initial code for 6LoWPAN Generic Header Compression (GHC) support
- Refactor Bluetooth LE scan & advertising behind dedicated workqueue
- Cleanups to Bluetooth H:5 HCI driver
- Support for Toshiba Broadcom based Bluetooth controllers
- Use continuous scanning when establishing Bluetooth LE connections
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
郭永刚 reported that one could simply crash the kernel as root by
using a simple program:
int socket_fd;
struct sockaddr_in addr;
addr.sin_port = 0;
addr.sin_addr.s_addr = INADDR_ANY;
addr.sin_family = 10;
socket_fd = socket(10,3,0x40000000);
connect(socket_fd , &addr,16);
AF_INET, AF_INET6 sockets actually only support 8-bit protocol
identifiers. inet_sock's skc_protocol field thus is sized accordingly,
thus larger protocol identifiers simply cut off the higher bits and
store a zero in the protocol fields.
This could lead to e.g. NULL function pointer because as a result of
the cut off inet_num is zero and we call down to inet_autobind, which
is NULL for raw sockets.
kernel: Call Trace:
kernel: [<ffffffff816db90e>] ? inet_autobind+0x2e/0x70
kernel: [<ffffffff816db9a4>] inet_dgram_connect+0x54/0x80
kernel: [<ffffffff81645069>] SYSC_connect+0xd9/0x110
kernel: [<ffffffff810ac51b>] ? ptrace_notify+0x5b/0x80
kernel: [<ffffffff810236d8>] ? syscall_trace_enter_phase2+0x108/0x200
kernel: [<ffffffff81645e0e>] SyS_connect+0xe/0x10
kernel: [<ffffffff81779515>] tracesys_phase2+0x84/0x89
I found no particular commit which introduced this problem.
CVE: CVE-2015-8543
Cc: Cong Wang <cwang@twopensource.com>
Reported-by: 郭永刚 <guoyonggang@360.cn>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolve conflict between commit 264640fc2c ("ipv6: distinguish frag
queues by device for multicast and link-local packets") from the net
tree and commit 029f7f3b87 ("netfilter: ipv6: nf_defrag: avoid/free
clone operations") from the nf-next tree.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Conflicts:
net/ipv6/netfilter/nf_conntrack_reasm.c
XFRM can deal with SYNACK messages, sent while listener socket
is not locked. We add proper rcu protection to __xfrm_sk_clone_policy()
and xfrm_sk_policy_lookup()
This might serve as the first step to remove xfrm.xfrm_policy_lock
use in fast path.
Fixes: fa76ce7328 ("inet: get rid of central tcp/dccp listener timer")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will soon switch sk->sk_policy[] to RCU protection,
as SYNACK packets are sent while listener socket is not locked.
This patch simply adds RCU grace period before struct xfrm_policy
freeing, and the corresponding rcu_head in struct xfrm_policy.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a static inline function ipv6_addr_prefix_copy which
copies a ipv6 address prefix(argument pfx) into the ipv6 address prefix.
The prefix len is given by plen as bits. This function mainly based on
ipv6_addr_prefix which copies one address prefix from address into a new
ipv6 address destination and zero all other address bits.
The difference is that ipv6_addr_prefix_copy don't get a prefix from an
ipv6 address, it sets a prefix to an ipv6 address with keeping other
address bits. The use case is for context based address compression
inside 6LoWPAN IPHC header which keeping ipv6 prefixes inside a context
table to lookup address-bits without sending them.
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: Łukasz Duda <lukasz.duda@nordicsemi.no>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch will introduce a 6lowpan entry into the debugfs if enabled.
Inside this 6lowpan directory we create a subdirectories of all 6lowpan
interfaces to offer a per interface debugfs support.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch introduces register and unregister functionality for lowpan
interfaces. While register a lowpan interface there are several things
which need to be initialize by the 6lowpan subsystem. Upcoming
functionality need to register/unregister per interface components e.g.
debugfs entry.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This flag just tells us whether hdev->adv_instances is empty or not.
We can equally well use the list_empty() function to get this
information.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The request to update HCI during power on is always coming either from
hdev->req_workqueue or through an ioctl, so it's safe to use
hci_req_sync for it. This way we also eliminate potential races with
incoming mgmt commands or other actions while powering on.
Part of this refactoring is the splitting of mgmt_powered() into
mgmt_power_on() and __mgmt_power_off() functions. The main reason is
the different requirements as far as hdev locking is concerned, as
highlighted with the __ prefix of the power off API.
Since the power on in the case of clearing the AUTO_OFF flag cannot be
done synchronously in the set_powered mgmt handler, the hci_power_on
work callback is extended to cover this (which also simplifies the
set_powered helper a lot).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the other discoverable changes are behind req_workqueue now it
only makes sense to move the discoverable timeout there as well.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The discoverable mode is intrinsically linked with the connectable
mode e.g. through sharing the same HCI command (Write Scan Enable) for
BR/EDR. It makes therefore sense to move it to hci_request.c and run
the changes through the same hdev->req_workqueue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This way the connectable changes are synchronized against each other,
which helps avoid potential races. The connectable mode is also linked
together with LE advertising which makes is more convenient to have it
behind the same workqueue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This paves the way for eventually performing advertising changes
through the hdev->req_workqueue. Some new APIs need to be exposed from
mgmt.c to hci_request.c and vice-versa, but many of them will go away
once hdev->req_workqueue gets used.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since Add/Remove Device perform the page scan updates independently
from the HCI command completion we've introduced a potential race when
multiple mgmt commands are queued. Doing the page scan updates through
the req_workqueue ensures that the state changes are performed in a
race-free manner.
At the same time, to make the request helper more widely usable,
extend it to also cover Inquiry Scan changes since those are behind
the same HCI command. This is also reflected in the new name of the
API as well as the work struct name.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Only needed when meta nftrace rule(s) were added.
The assumption is that no such rules are active, so the call to
nft_trace_init is "never" needed.
When nftrace rules are active, we always call the nft_trace_* functions,
but will only send netlink messages when all of the following are true:
- traceinfo structure was initialised
- skb->nf_trace == 1
- at least one subscriber to trace group.
Adding an extra conditional
(static_branch ... && skb->nf_trace)
nft_trace_init( ..)
Is possible but results in a larger nft_do_chain footprint.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nft monitor mode can then decode and display this trace data.
Parts of LL/Network/Transport headers are provided as separate
attributes.
Otherwise, printing IP address data becomes virtually impossible
for userspace since in the case of the netdev family we really don't
want userspace to have to know all the possible link layer types
and/or sizes just to display/print an ip address.
We also don't want userspace to have to follow ipv6 header chains
to get the s/dport info, the kernel already did this work for us.
To avoid bloating nft_do_chain all data required for tracing is
encapsulated in nft_traceinfo.
The structure is initialized unconditionally(!) for each nft_do_chain
invocation.
This unconditionall call will be moved under a static key in a
followup patch.
With lots of help from Patrick McHardy and Pablo Neira.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Introduce sock->sk_cgrp_data which is a struct sock_cgroup_data.
->sk_cgroup_prioidx and ->sk_classid are moved into it. The struct
and its accessors are defined in cgroup-defs.h. This is to prepare
for overloading the fields with a cgroup pointer.
This patch mostly performs equivalent conversions but the followings
are noteworthy.
* Equality test before updating classid is removed from
sock_update_classid(). This shouldn't make any noticeable
difference and a similar test will be implemented on the helper side
later.
* sock_update_netprioidx() now takes struct sock_cgroup_data and can
be moved to netprio_cgroup.h without causing include dependency
loop. Moved.
* The dummy version of sock_update_netprioidx() converted to a static
inline function while at it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
netprio builds per-netdev contiguous priomap array which is indexed by
css->id. The array is allocated using kzalloc() effectively limiting
the maximum ID supported to some thousand range. This patch caps the
maximum supported css->id to USHRT_MAX which should be way above what
is actually useable.
This allows reducing sock->sk_cgrp_prioidx to u16 from u32. The freed
up part will be used to overload the cgroup related fields.
sock->sk_cgrp_prioidx's position is swapped with sk_mark so that the
two cgroup related fields are adjacent.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 0d76d6e8b2 and merge
commit c402293bd7, reversing changes made
to c89359a42e.
The virtio-vsock device specification is not finalized yet. Michael
Tsirkin voiced concerned about merging this code when the hardware
interface (and possibly the userspace interface) could still change.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP SYNACK messages might now be attached to request sockets.
XFRM needs to get back to a listener socket.
Adds new helpers that might be used elsewhere :
sk_to_full_sk() and sk_const_to_full_sk()
Note: We also need to add RCU protection for xfrm lookups,
now TCP/DCCP have lockless listener processing. This will
be addressed in separate patches.
Fixes: ca6fb06518 ("tcp: attach SYNACK messages to request sockets instead of listener")
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since no more DSA driver uses the polling callback, and since
the phylib handles the link detection, remove the link polling
work and timer code.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
needing to reshuffle and fix some bugs. I merged mac80211
to get the right base for some of these changes.
* new mac80211 API for upcoming driver changes: EOSP handling,
key iteration
* scan abort changes allowing to cancel an ongoing scan
* VHT IBSS 80+80 MHz support
* re-enable full AP client state tracking after fixes
* various small fixes (that weren't relevant for mac80211)
* various cleanups
-----BEGIN PGP SIGNATURE-----
iQIcBAABCgAGBQJWZVw7AAoJEGt7eEactAAdQcgP/1bOBBKgCHWZ8xhqmhLIPPUP
AgkkyBcjCbSOWyE1axm5WQZM+fQvyGAcYsnhsK7h0Wy5Jvv6goNYhxkoD3L5lAKC
LkiiqokTpLx1Em6Iugn1sdgag8q7EquYYQN+hOEOWtp32pTsx3/pDglCtGu0SX1N
eystHEAu6mzPezat99M4s80fRlfBop3yaUuL5XopQFGtU37zfUgoXJB3BoXgxNjK
XyD22jtPDreDMndZ9ugfvMaiq3iKRBhKXqgGb3SqMaStIyRK8zAkHb5jg3CllMeq
bEsz4Rb4r+vtm2AVsUMWjfd/upQKwPwuvdvCvv4AQCO+aR9Rm+tR/wnnD4Gtnek5
zPQ6XWt/0V4CKGl+W9shnDSA1DZ3hTijJlaGsK+RUqEtdq903lEP7fc2GsSvlund
jXHfOExieuZOToKWTKpmNGsCw6fjJaGXNd/iLWo5VGAZS2X+JLmFZ94g43a6zOGZ
s1Gz4F3tz4u4Bd26NAK2Z6CQRvDS4OOyLIjl9vpB9Fk/9nQx3f7WD8aBTRuCVAtG
U2sFEUscz3rkdct30Gvkjm3ovmgc4pomTDvOpmNIsSCi2ygzGWHbEvSrrHdIjzVy
KDcvRs6bRtCL/WxaaEIk46M6+6aKlSnZytPLl7vkNnvxXuEF7GYdnNVSUbSH9Nte
XzT4+rZRiqyPZEGhBekw
=+5dd
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-12-07' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This pull request got a bit bigger than I wanted, due to
needing to reshuffle and fix some bugs. I merged mac80211
to get the right base for some of these changes.
* new mac80211 API for upcoming driver changes: EOSP handling,
key iteration
* scan abort changes allowing to cancel an ongoing scan
* VHT IBSS 80+80 MHz support
* re-enable full AP client state tracking after fixes
* various small fixes (that weren't relevant for mac80211)
* various cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
when A sends a data to B, then A close() and enter into SHUTDOWN_PENDING
state, if B neither claim his rwnd is 0 nor send SACK for this data, A
will keep retransmitting this data until t5 timeout, Max.Retrans times
can't work anymore, which is bad.
if B's rwnd is not 0, it should send abort after Max.Retrans times, only
when B's rwnd == 0 and A's retransmitting beyonds Max.Retrans times, A
will start t5 timer, which is also commit f8d9605243 ("sctp: Enforce
retransmission limit during shutdown") means, but it lacks the condition
peer rwnd == 0.
so fix it by adding a bit (zero_window_announced) in peer to record if
the last rwnd is 0. If it was, zero_window_announced will be set. and use
this bit to decide if start t5 timer when local.state is SHUTDOWN_PENDING.
Fixes: commit f8d9605243 ("sctp: Enforce retransmission limit during shutdown")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dmitry Vyukov reported that SCTP was triggering a WARN on socket destroy
related to disabling sock timestamp.
When SCTP accepts an association or peel one off, it copies sock flags
but forgot to call net_enable_timestamp() if a packet timestamping flag
was copied, leading to extra calls to net_disable_timestamp() whenever
such clones were closed.
The fix is to call net_enable_timestamp() whenever we copy a sock with
that flag on, like tcp does.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3511494ce2 ("vxlan: Group Policy extension") changed definition of
VXLAN_HF_RCO from 0x00200000 to BIT(24). This is obviously incorrect. It's
also in violation with the RFC draft.
Fixes: 3511494ce2 ("vxlan: Group Policy extension")
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement new functionality for aborting an ongoing scan.
Add NL80211_CMD_ABORT_SCAN to the nl80211 interface. After
aborting the scan, driver shall provide the scan status by
calling cfg80211_scan_done().
Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com>
Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com>
[change command to take wdev instead of netdev so that it
can be used on p2p-device scans]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add new VIF flag, that will allow get NOA update
notification when driver will request this, even
this is not pure P2P vif (eg. STA vif).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
add ieee80211_iter_keys_rcu() to iterate over uploaded
keys in atomic context (when rcu is locked)
The station removal code removes the keys only after
calling synchronize_net(), so it's not safe to iterate
the keys at this point (and postponing the actual key
deletion with call_rcu() might result in some
badly-ordered ops calls).
Add a flag to indicate a station is being removed,
and skip the configured keys if it's set.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This can happen when the driver needs to send less frames
than expected and then needs to close the SP.
Mac80211 still needs to set the more_data properly based
on its buffer state (ps_tx_buffer and buffered frames on
other TIDs).
To that end, refactor the code that delivers frames upon
uAPSD trigger frames to be able to get only the more_data
bit without actually delivering those frames in case the
driver is just asking to set a NDP with EOSP and MORE_DATA
bit properly set.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function is a very simple wrapper around another one,
just adds a few default parameters, so replace it with a
static inline instead of using EXPORT_SYMBOL, reducing
the module size slightly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices or drivers cannot deal with having the same station
address for different virtual interfaces, say as a client to two
virtual AP interfaces. Rather than requiring each driver with a
limitation like that to enforce it, add a hardware flag for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I want to get the full off-channel bugfix since later code depends on
it, as well as the AP client state change so I can revert it correctly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Nikolay Borisov