With the addition of a device platform mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus/2640/i2c' of git://git.fluff.org/bjdooks/linux: (21 commits)
mach-ux500: set proper I2C platform data from MOP500s
i2c-nomadik: break out single messsage transmission
i2c-nomadik: reset the hw after status check
i2c-nomadik: remove the unnecessary delay
i2c-nomadik: change the TX and RX threshold
i2c-nomadik: add code to retry on timeout failure
i2c-nomadik: use pm_runtime API
i2c-nomadik: print abort cause only on abort tag
i2c-nomadik: correct adapter timeout initialization
i2c-nomadik: remove the redundant error message
i2c-nomadik: corrrect returned error numbers
i2c-nomadik: fix speed enumerator
i2c-nomadik: make i2c timeout specific per i2c bus
i2c-nomadik: add regulator support
i2c: i2c-sh_mobile bus speed platform data V2
i2c: i2c-sh_mobile clock string removal
i2c-eg20t: Support new device ML7223 IOH
i2c: tegra: Add de-bounce cycles.
i2c: tegra: fix repeated start handling
i2c: tegra: recover from spurious interrupt storm
...
Reduce code size in the message transfer function by factoring out
a single-message transfer function.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
In case of I2C timeout, reset the HW only after the HW status
is read, otherwise the staus will be lost.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The delay in the driver seems to be not needed, so remove it.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Markus Grape <markus.grape@stericsson.com>
Tested-by: Per Persson <per.xb.persson@stericsson.com>
Tested-by: Chethan Krishna N <chethan.krishna@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
1) Increase RX FIFO threshold so that there is a reduction in
the number of interrupts handled to complete a transaction.
2) Fill TX FIFO in the write function.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
It is seen that i2c-nomadik controller randomly stops generating the
interrupts leading to a i2c timeout. As a workaround to this problem,
add retries to the on going transfer on failure.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Use the pm_runtime API for pins control.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
[deleted some surplus runtime PM code]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Modify the code to:
1)Print the cause of i2c failure only if the status is set to ABORT.
2)Print slave address on send/receive fail, will help in which slave
failed.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Correct the incorrect initialization of adapter timeout not to be
in milliseconds, as it needs to be done in jiffies.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The abort cause string itself is an error, so remove the redundant
explicit error message.
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The code was returning bad error numbers or just -1 in some cases.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add option to have different i2c timeout delay for different i2c buses
specified in platform data. Default to the old value unless specified.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This on-chip I2C controller needs to fetch the regulator
representing its voltage domain so that it won't be switched off.
Signed-off-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* Fix white space.
* Rename labels to something meaningful.
* Prefix defines with PORT_ to avoid collision with macros from
<linux/parport.h>.
* Add const markers where possible.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Don't let other driver config options influence us, as it makes the
code more complex and fragile for a small benefit. There's nothing
wrong with instantiating I2C devices even if they don't have a driver.
And we're talking about 835 extra bytes in the binary on x86-64,
that's hardly worth arguing about.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Woodhouse <david.woodhouse@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Scanning the BIOS memory for the apanel information is costly, so
avoid doing it on non-Fujitsu machines.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
I don't know if Fujitsu is ever going to produce Patsburg-based
machines, but if they do, I'd rather not probe the secondary (IDF)
SMBus channels. At least not until we have a good reason for doing so.
On a side note, I'm not even sure if it is right to enable detection
of HWMON and DDC devices on the IDF channels. Time will tell...
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds the SMBus controller DeviceID for the Intel Panther Point PCH.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
* 'sh-latest' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (23 commits)
sh: Ignore R_SH_NONE module relocations.
SH: SE7751: Fix pcibios_map_platform_irq prototype.
sh: remove warning and warning_symbol from struct stacktrace_ops
sh: wire up sys_sendmmsg.
clocksource: sh_tmu: Runtime PM support
clocksource: sh_tmu: __clocksource_updatefreq_hz() update
clocksource: sh_cmt: Runtime PM support
clocksource: sh_cmt: __clocksource_updatefreq_hz() update
dmaengine: shdma: synchronize RCU before freeing, simplify spinlock
dmaengine: shdma: add runtime- and system-level power management
dmaengine: shdma: fix locking
sh: sh-sci: sh7377 and sh73a0 build fixes
sh: cosmetic improvement: use an existing pointer
serial: sh-sci: suspend/resume wakeup support V2
serial: sh-sci: Runtime PM support
sh: select IRQ_FORCED_THREADING.
sh: intc: Set virtual IRQs as nothread.
sh: fixup fpu.o compile order
i2c: add a module alias to the sh-mobile driver
ALSA: add a module alias to the FSI driver
...
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (27 commits)
PCI: Don't use dmi_name_in_vendors in quirk
PCI: remove unused AER functions
PCI/sysfs: move bus cpuaffinity to class dev_attrs
PCI: add rescan to /sys/.../pci_bus/.../
PCI: update bridge resources to get more big ranges when allocating space (again)
KVM: Use pci_store/load_saved_state() around VM device usage
PCI: Add interfaces to store and load the device saved state
PCI: Track the size of each saved capability data area
PCI/e1000e: Add and use pci_disable_link_state_locked()
x86/PCI: derive pcibios_last_bus from ACPI MCFG
PCI: add latency tolerance reporting enable/disable support
PCI: add OBFF enable/disable support
PCI: add ID-based ordering enable/disable support
PCI hotplug: acpiphp: assume device is in state D0 after powering on a slot.
PCI: Set PCIE maxpayload for card during hotplug insertion
PCI/ACPI: Report _OSC control mask returned on failure to get control
x86/PCI: irq and pci_ids patch for Intel Panther Point DeviceIDs
PCI: handle positive error codes
PCI: check pci_vpd_pci22_wait() return
PCI: Use ICH6_GPIO_EN in ich6_lpc_acpi_gpio
...
Fix up trivial conflicts in include/linux/pci_ids.h: commit a6e5e2be44
moved the intel SMBUS ID definitons to the i2c-i801.c driver.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
Commit b826291c, "drivercore/dt: add a match table pointer to struct
device" added an of_match pointer to struct device to cache the
of_match_table entry discovered at driver match time. This was unsafe
because matching is not an atomic operation with probing a driver. If
two or more drivers are attempted to be matched to a driver at the
same time, then the cached matching entry pointer could get
overwritten.
This patch reverts the of_match cache pointer and reworks all users to
call of_match_device() directly instead.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
alg_data is already a pointer which must be passed directly.
Reported-by: Dieter Ripp <ripp@systecnet.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ben Dooks <ben-i2c@fluff.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support to the i2c-sh_mobile driver for setting
the I2C bus speed using platform data.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Remove the clock string magic from the i2c-sh_mobile driver
now when all platforms support clkdev properly.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This enables debouncing of the I2C lines. The debounce period is
2 * the debounce register field value, in terms of the I2C block's main
clock. The Tegra TRM indicates that a setting yielding >50nS is
desirable. Hence, a setting of 2 => 4 clocks @ 72MHz => ~55nS.
Signed-off-by: Ken Radtke <kradtke@nvidia.com>
[swarren: Added commit description body,
Fixed 80-column limit, Reverted file permission change]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
A repeated start should be used for all but the last msg in an xfer. The
NOSTART flag is for skipping the START frame (addr/rw)
Signed-off-by: Erik Gilling <konkers@android.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Re-init the I2C controller when an IRQ arrives with no
I2C_INT_STATUS bits set to indicate why the interrupt was sent.
Storms of such mystery interrupts are infrequently seen.
Dump some more status when these interrupts arrive. Set an error
for the current request and wake up the requester (rather than
timing out the request or possibly silently ignoring the interrupts).
If the I2C block is inside the DVC, also ACK the DVC I2C transfer
done interrupt in the ISR error return path, as is done for the
normal return path.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
[swarren: Fix minor checkpatch whitespace issue, commit tag]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
For Tegra i2c controller to function properly new slave mode must be
enabled.
swarren notes:
In particular, I found this was needed when working on enabling the
Tegra audio driver on the Seaboard board. There are two different PCB
layouts for this board; a "clamshell" version, which works just fine
without this change, and the original non-clamshell version, which needs
this change in order for I2C to operate correctly. Without it, I2C
probing fails for some devices, e.g. with:
wm8903 0-001a: Device with ID register 0 is not a WM8903
wm8903 0-001a: asoc: failed to probe CODEC wm8903.0-001a: -19
asoc: failed to instantiate card tegra-wm8903: -19
ALSA device list:
No soundcards found.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Use a standard list with proper locking to handle the list of
adapters. Thankfully it only matters on systems with more than one
parallel port, which are very rare.
Thanks to Lukasz Kapiec for reporting the problem to me.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org
Move the SMBus device ID definitions of recent devices from pci_ids.h
to the i2c-i801.c driver file. They don't have to be shared, as they
are clearly identified and only used in this driver. In the future,
such IDs will go to i2c-i801 directly. This will make adding support
for new devices much faster and easier, as it will avoid cross-
subsystem patch sets and merge conflicts.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Seth Heasley <seth.heasley@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch enables I2C driver autoloading on sh-mobile systems.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The cell's platform_data is now accessed with a helper function;
change clients to use that, and remove the now-unused data_size.
Note that the mfd's platform_data is marked __devinitdata. This
is still correct in all cases except for the timbgpio driver, whose
remove hook has been changed to no longer reference the pdata.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus/2639/i2c-2' of git://git.fluff.org/bjdooks/linux:
i2c-pxa2xx: Don't clear isr bits too early
i2c-pxa2xx: Fix register offsets
i2c-pxa2xx: pass of_node from platform driver to adapter and publish
i2c-pxa2xx: check timeout correctly
i2c-pxa2xx: add support for shared IRQ handler
i2c-pxa2xx: Add PCI support for PXA I2C controller
ARM: pxa2xx: reorganize I2C files
i2c-pxa2xx: use dynamic register layout
i2c-mxs: set controller to pio queue mode after reset
i2c-eg20t: support new device OKI SEMICONDUCTOR ML7213 IOH
i2c/busses: Add support for Diolan U2C-12 USB-I2C adapter
isr is passed later into i2c_pxa_irq_txempty and
i2c_pxa_irq_rxfull and they may use some other bits
than irq sources.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix regression that was introduced by dynamic register layout.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
the of_node will auto-publish devices which are added to the device
tree.
Commit 925bb9c6 aka ("of/i2c: Fix module load order issue caused by
of_i2c.c) moved the of_i2c_register_devices() function from the i2c core
back to the drivers. This patch does the same thing for the pxa driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
timeout here maybe 0 if the event occured and a task with a higher
priority stole the cpu and we were sleeping longer than the timeout
value we specified.
In case of a real timeout I changed the error code to I2C_RETRY so we
retry the transfer.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Sodaville has three of them on a single IRQ. IRQF_DISABLED is removed
because it is a NOP allready and scheduled for removal.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The Sodaville I2C controller is almost the same as found on PXA2xx. The
difference:
- the register are at a different offset
- no slave support
The PCI probe code adds three platform devices which are probed then by
the platform code.
The X86 part also adds dummy clock defines because we don't have HW
clock support.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch moves the platform data definition from
arch/arm/plat-pxa/include/plat/i2c.h to include/linux/i2c/pxa-i2c.h so
it can be accessed from x86 the same way as on ARM.
This change should make no functional change to the PXA code. The move
is verified by building the following defconfigs:
cm_x2xx_defconfig corgi_defconfig em_x270_defconfig ezx_defconfig
imote2_defconfig pxa3xx_defconfig spitz_defconfig zeus_defconfig
raumfeld_defconfig magician_defconfig mmp2_defconfig pxa168_defconfig
pxa910_defconfig
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This will prepare the driver to handle register layouts where certain
registers are not available at all.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
mxs_reset_block() clears the PIO_QUEUE_MODE bit. So we have
to set it again after a controller reset.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Samuel Ortiz