Add helpers to read the min/max frequency being used
by SLPC. This is done by send a H2G command which forces
SLPC to update the shared data struct which can then be
read. These helpers will be used in a sysfs patch later
on.
v2: Address review comments (Michal W)
v3: Return err in case of query failure (Michal W)
v4: Move decode_min/max_freq to this patch
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Signed-off-by: Sundaresan Sujaritha <sujaritha.sundaresan@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730202119.23810-9-vinay.belgaumkar@intel.com
Add param set h2g helpers to set the min and max frequencies
for use by SLPC.
v2: Address review comments (Michal W)
v3: Check for positive error code (Michal W)
v4: Print generic error in set_param (Michal W)
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Sundaresan Sujaritha <sujaritha.sundaresan@intel.com>
Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730202119.23810-8-vinay.belgaumkar@intel.com
The assumption when it was added was that GT would not be
holding any gt_pm references. However, uc_init is called
from gt_init_hw, which holds a forcewake ref. If SLPC
enable fails, we will still be holding this ref, which will
result in the BUG_ON.
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730202119.23810-7-vinay.belgaumkar@intel.com
Add methods for interacting with GuC for enabling SLPC. Enable
SLPC after GuC submission has been established. GuC load will
fail if SLPC cannot be successfully initialized. Add various
helper methods to set/unset the parameters for SLPC. They can
be set using H2G calls or directly setting bits in the shared
data structure.
v2: Address several review comments, add new helpers for
decoding the SLPC min/max frequencies. Use masks instead of hardcoded
constants. (Michal W)
v3: Split global_state_to_string function, and check for positive
non-zero return value from intel_guc_send() (Michal W)
v4: Optimize the stringify function and other comments (Michal W)
v5: Enable slpc as well before declaring GuC submission status (Michal W)
v6: Checkpatch()
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Signed-off-by: Sundaresan Sujaritha <sujaritha.sundaresan@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730202119.23810-6-vinay.belgaumkar@intel.com
Allocate data structures for SLPC and functions for
initializing on host side.
v2: Address review comments (Michal W)
v3: Remove unnecessary header includes (Michal W)
v4: Rebase
v5: Move allocation of shared data into slpc_init() (Michal W)
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Signed-off-by: Sundaresan Sujaritha <sujaritha.sundaresan@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730202119.23810-5-vinay.belgaumkar@intel.com
Add constants and params that are needed to configure SLPC.
v2: Add a new abi header for SLPC. Replace bitfields with
genmasks. Address other comments from Michal W.
v3: Add slpc H2G format in abi, other review commments (Michal W)
v4: Update status bits according to latest spec
v5: checkpatch()
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Signed-off-by: Sundaresan Sujaritha <sujaritha.sundaresan@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730202119.23810-4-vinay.belgaumkar@intel.com
Also ensure uc_init is called before we initialize RPS so that we
can check for SLPC support. We do not need to enable up/down
interrupts when SLPC is enabled. However, we still need the ARAT
interrupt, which will be enabled separately later.
v2: Explicitly return from intel_rps_enable with slpc check (Matthew B)
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Signed-off-by: Sundaresan Sujaritha <sujaritha.sundaresan@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730202119.23810-3-vinay.belgaumkar@intel.com
Add macros to check for SLPC support. This feature is currently supported
for Gen12+ and enabled whenever GuC submission is enabled/selected.
Include templates for SLPC init/fini and enable.
v2: Move SLPC helper functions to intel_guc_slpc.c/.h. Define
basic template for SLPC structure in intel_guc_slpc_types.h.
Fix copyright (Michal W)
v3: Review comments (Michal W)
v4: Include supported/selected inside slpc struct (Michal W)
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Signed-off-by: Sundaresan Sujaritha <sujaritha.sundaresan@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730202119.23810-2-vinay.belgaumkar@intel.com
There's a missing sentinel since we are not using ARRAY_SIZE(), but rather
checking that the .start is 0 to stop the iteration in mcr_range().
BUG: KASAN: global-out-of-bounds in mcr_range.isra.0+0x69/0xa0 [i915]
Read of size 4 at addr ffffffffa0889928 by task modprobe/3881
Fixes: d8905ba705 ("drm/i915/xehp: Define multicast register ranges")
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730191115.2514581-1-lucas.demarchi@intel.com
No need to hand roll the set_placements stuff, now that we have a helper
for this.
v2: add back the -ENODEV checking since it's possible for stolen to be
probed, and yet still be non-functional
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20210729094731.1953091-1-matthew.auld@intel.com
CNL is the only platform with GRAPHICS_VER == 10. With its removal we
don't need to handle that version anymore.
Also we can now reduce the max number of slices: the call to
intel_sseu_set_info() with the highest number of slices comes from SKL
and BDW with 3 slices. Recent platforms actually increase the
number of subslices so the number of slices remain 1.
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728220326.1578242-3-lucas.demarchi@intel.com
The module init code is somewhat misplaced in i915_pci.c, since it
needs to pull in init/exit functions from every part of the driver and
pollutes the include list a lot.
Extract an i915_module.c file which pulls all the bits together, and
allows us to massively trim the include list of i915_pci.c.
The downside is that have to drop the error path check Jason added to
catch when we set up the pci driver too early. I think that risk is
acceptable for this pretty nice include.
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727121037.2041102-11-daniel.vetter@ffwll.ch
With the global kmem_cache shrink infrastructure gone there's nothing
special and we can convert them over.
I'm doing this split up into each patch because there's quite a bit of
noise with removing the static global.slab_vmas to just a
slab_vmas.
We have to keep i915_drv.h include in i915_globals otherwise there's
nothing anymore that pulls in GEM_BUG_ON.
v2: Make slab static (Jason, 0day)
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727121037.2041102-9-daniel.vetter@ffwll.ch
With the global kmem_cache shrink infrastructure gone there's nothing
special and we can convert them over.
I'm doing this split up into each patch because there's quite a bit of
noise with removing the static global.slab_dependencies|priorities to just a
slab_dependencies|priorities.
v2: Make slab static (Jason, 0day)
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727121037.2041102-8-daniel.vetter@ffwll.ch
With the global kmem_cache shrink infrastructure gone there's nothing
special and we can convert them over.
I'm doing this split up into each patch because there's quite a bit of
noise with removing the static global.slab_requests|execute_cbs to just a
slab_requests|execute_cbs.
v2: Make slab static (Jason, 0day)
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727121037.2041102-7-daniel.vetter@ffwll.ch
With the global kmem_cache shrink infrastructure gone there's nothing
special and we can convert them over.
I'm doing this split up into each patch because there's quite a bit of
noise with removing the static global.slab_objects to just a
slab_objects.
v2: Make slab static (Jason, 0day)
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727121037.2041102-6-daniel.vetter@ffwll.ch
With the global kmem_cache shrink infrastructure gone there's nothing
special and we can convert them over.
I'm doing this split up into each patch because there's quite a bit of
noise with removing the static global.slab_luts to just a
slab_luts.
v2: Make slab static (Jason, 0day)
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727121037.2041102-5-daniel.vetter@ffwll.ch
With the global kmem_cache shrink infrastructure gone there's nothing
special and we can convert them over.
I'm doing this split up into each patch because there's quite a bit of
noise with removing the static global.slab_ce to just a
slab_ce.
v2: Make slab static (Jason, 0day)
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727121037.2041102-4-daniel.vetter@ffwll.ch
With the global kmem_cache shrink infrastructure gone there's nothing
special and we can convert them over.
I'm doing this split up into each patch because there's quite a bit of
noise with removing the static global.slab_blocks to just a
slab_blocks.
v2: Make slab static (Jason, 0day)
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727121037.2041102-3-daniel.vetter@ffwll.ch
With the global kmem_cache shrink infrastructure gone there's nothing
special and we can convert them over.
I'm doing this split up into each patch because there's quite a bit of
noise with removing the static global.slab_cache to just a slab_cache.
v2: Make slab static (Jason, 0day)
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727121037.2041102-2-daniel.vetter@ffwll.ch
When modesetting (aka the full pci driver, which has nothing to do
with disable_display option, which just gives you the full pci driver
without the display driver) is disabled, we load nothing and do
nothing.
So move that check first, for a bit of orderliness. With Jason's
module init/exit table this now becomes trivial.
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727121037.2041102-1-daniel.vetter@ffwll.ch
During a rebase the parameters were partially renamed, but not
completely. Since the subsequent patches that start using this macro
haven't landed on an upstream tree yet this didn't cause a build
failure.
Fixes: 086df54e20 ("drm/i915/xehpsdv: add initial XeHP SDV definitions")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Caz Yokoyama <caz.yokoyama@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723174239.1551352-2-matthew.d.roper@intel.com
Unblock GuC submission on Gen11+ platforms.
v2:
(Martin Peres / John H)
- Delete debug message when GuC is disabled by default on certain
platforms
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-34-matthew.brost@intel.com
Implement a simple static mapping algorithm of the i915 priority levels
(int, -1k to 1k exposed to user) to the 4 GuC levels. Mapping is as
follows:
i915 level < 0 -> GuC low level (3)
i915 level == 0 -> GuC normal level (2)
i915 level < INT_MAX -> GuC high level (1)
i915 level == INT_MAX -> GuC highest level (0)
We believe this mapping should cover the UMD use cases (3 distinct user
levels + 1 kernel level).
In addition to static mapping, a simple counter system is attached to
each context tracking the number of requests inflight on the context at
each level. This is needed as the GuC levels are per context while in
the i915 levels are per request.
v2:
(Daniele)
- Add BUILD_BUG_ON to enforce ordering of priority levels
- Add missing lockdep to guc_prio_fini
- Check for return before setting context registered flag
- Map DISPLAY priority or higher to highest guc prio
- Update comment for guc_prio
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-33-matthew.brost@intel.com
Some testing environments and some heavier tests are slower than
previous limits allowed for. For example, it can take multiple seconds
for the 'context has been reset' notification handler to reach the
'kill the requests' code in the 'active' version of the 'reset
engines' test. During which time the selftest gets bored, gives up
waiting and fails the test.
There is also an async thread that the selftest uses to pump work
through the hardware in parallel to the context that is marked for
reset. That also could get bored waiting for completions and kill the
test off.
Lastly, the flush at the of various test sections can also see
timeouts due to the large amount of work backed up. This is also true
of the live_hwsp_read test.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-32-matthew.brost@intel.com
When GuC submission is enabled, the GuC controls engine resets. Rather
than explicitly triggering a reset, the driver must submit a hanging
context to GuC and wait for the reset to occur.
Conversely, one of the tests specifically sends hanging batches to the
engines but wants them to sit around until a manual reset of the full
GT (including GuC itself). That means disabling GuC based engine
resets to prevent those from killing the hanging batch too soon. So,
add support to the scheduling policy helper for disabling resets as
well as making them quicker!
In GuC submission mode, the 'is engine idle' test basically turns into
'is engine PM wakelock held'. Independently, there is a heartbeat
disable helper function that the tests use. For unexplained reasons,
this acquires the engine wakelock before disabling the heartbeat and
only releases it when re-enabling the heartbeat. As one of the tests
tries to do a wait for idle in the middle of a heartbeat disabled
section, it is therefore guaranteed to always fail. Added a 'no_pm'
variant of the heartbeat helper that allows the engine to be asleep
while also having heartbeats disabled.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-31-matthew.brost@intel.com
When GuC submission is enabled, the GuC controls engine resets. Rather
than explicitly triggering a reset, the driver must submit a hanging
context to GuC and wait for the reset to occur.
Signed-off-by: Rahul Kumar Singh <rahul.kumar.singh@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-29-matthew.brost@intel.com
When GuC submission is enabled, the GuC controls engine resets. Rather
than explicitly triggering a reset, the driver must submit a hanging
context to GuC and wait for the reset to occur.
Signed-off-by: Rahul Kumar Singh <rahul.kumar.singh@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-28-matthew.brost@intel.com
There are many ways in which the hangcheck selftest can fail. Very few
of them actually printed an error message to say what happened. So,
fill in the missing messages.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-27-matthew.brost@intel.com
This adds GuC backend support for i915_request_cancel(), which in turn
makes CONFIG_DRM_I915_REQUEST_TIMEOUT work.
This implementation makes use of fence while there are likely simplier
options. A fence was chosen because of another feature coming soon
which requires a user to block on a context until scheduling is
disabled. In that case we return the fence to the user and the user can
wait on that fence.
v2:
(Daniele)
- A comment about locking the blocked incr / decr
- A comments about the use of the fence
- Update commit message explaining why fence
- Delete redundant check blocked count in unblock function
- Ring buffer implementation
- Comment about blocked in submission path
- Shorter rpm path
v3:
(Checkpatch)
- Fix typos in commit message
(Daniel)
- Rework to simplier locking structure in guc_context_block / unblock
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-26-matthew.brost@intel.com
When using GuC submission, if a context gets banned disable scheduling
and mark all inflight requests as complete.
Cc: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-25-matthew.brost@intel.com
The media watchdog mechanism involves GuC doing a silent reset and
continue of the hung context. This requires the i915 driver provide a
golden context to GuC in the ADS.
v2:
(Matthew Brost):
- Fix memory corruption in shmem_read
(John H)
- Use locals rather than defines for LR_* + SKIP_SIZE
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-24-matthew.brost@intel.com
Added the scheduling policy parameters to the 'guc_info' debugfs state
dump.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-23-matthew.brost@intel.com
Changing the reset module parameter has no effect on a running GuC.
The corresponding entry in the ADS must be updated and then the GuC
informed via a Host2GuC message.
The new debugfs interface to module parameters allows this to happen.
However, connecting the parameter data address back to anything useful
is messy. One option would be to pass a new private data structure
address through instead of just the parameter pointer. However, that
means having a new (and different) data structure for each parameter
and a new (and different) write function for each parameter. This
method keeps everything generic by instead using a string lookup on
the directory entry name.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-22-matthew.brost@intel.com
Use the official driver default scheduling policies for configuring
the GuC scheduler rather than a bunch of hardcoded values.
v2:
(Matthew Brost)
- Move I915_ENGINE_WANT_FORCED_PREEMPTION to later patch
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Cc: Jose Souza <jose.souza@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-21-matthew.brost@intel.com
In the case of a full GPU reset (e.g. because GuC has died or because
GuC's hang detection has been disabled), the driver can't rely on GuC
reporting the guilty context. Instead, the driver needs to scan all
active contexts and find one that is currently executing, as per the
execlist mode behaviour. In GuC mode, this scan is different to
execlist mode as the active request list is handled very differently.
Similarly, the request state dump in debugfs needs to be handled
differently when in GuC submission mode.
Also refactured some of the request scanning code to avoid duplication
across the multiple code paths that are now replicating it.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-20-matthew.brost@intel.com
We receive notification of an engine reset from GuC at its
completion. Meaning GuC has potentially cleared any HW state
we may have been interested in capturing. GuC resumes scheduling
on the engine post-reset, as the resets are meant to be transparent,
further muddling our error state.
There is ongoing work to define an API for a GuC debug state dump. The
suggestion for now is to manually disable FW initiated resets in cases
where debug state is needed.
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-19-matthew.brost@intel.com
Clear the 'disable resets' flag to allow GuC to reset hung contexts
(detected via pre-emption timeout).
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-18-matthew.brost@intel.com
It is impossible to seal all race conditions of resets occurring
concurrent to other operations. At least, not without introducing
excesive mutex locking. Instead, don't complain if it occurs. In
particular, don't complain if trying to send a H2G during a reset.
Whatever the H2G was about should get redone once the reset is over.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-17-matthew.brost@intel.com
The driver must provide GuC with a list of mmio registers
that should be saved/restored during a GuC-based engine reset.
Unfortunately, the list must be dynamically allocated as its size is
variable. That means the driver must generate the list twice - once to
work out the size and a second time to actually save it.
v2:
(Alan / CI)
- GEN7_GT_MODE -> GEN6_GT_MODE to fix WA selftest failure
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Fernando Pacheco <fernando.pacheco@intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-16-matthew.brost@intel.com
The GuC can implement execution qunatums, detect hung contexts and
other such things but it requires the timer expired interrupt to do so.
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
CC: John Harrison <John.C.Harrison@Intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-15-matthew.brost@intel.com
GuC will notify the driver, via G2H, if it fails to
reset an engine. We recover by resorting to a full GPU
reset.
v2:
(John Harrison):
- s/drm_dbg/drm_err
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Fernando Pacheco <fernando.pacheco@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-14-matthew.brost@intel.com
GuC will issue a reset on detecting an engine hang and will notify
the driver via a G2H message. The driver will service the notification
by resetting the guilty context to a simple state or banning it
completely.
v2:
(John Harrison)
- Move msg[0] lookup after length check
v3:
(John Harrison)
- s/drm_dbg/drm_err
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-13-matthew.brost@intel.com
The new GuC interface introduces an MMIO H2G command,
INTEL_GUC_ACTION_RESET_CLIENT, which is used to implement suspend. This
MMIO tears down any active contexts generating a context reset G2H CTB
for each. Once that step completes the GuC tears down the CTB
channels. It is safe to suspend once this MMIO H2G command completes
and all G2H CTBs have been processed. In practice the i915 will likely
never receive a G2H as suspend should only be called after the GPU is
idle.
Resume is implemented in the same manner as before - simply reload the
GuC firmware and reinitialize everything (e.g. CTB channels, contexts,
etc..).
v2:
(Michel / John H)
- INTEL_GUC_ACTION_RESET_CLIENT 0x5B01 -> 0x5507
Cc: John Harrison <john.c.harrison@intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-12-matthew.brost@intel.com
Add disable GuC interrupts to intel_guc_sanitize(). Part of this
requires moving the guc_*_interrupt wrapper function into header file
intel_guc.h.
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727002348.97202-11-matthew.brost@intel.com
Vinay Belgaumkar