-----BEGIN PGP SIGNATURE-----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=/y4d
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Rework portdrv shutdown so it disables interrupts but doesn't
disable bus mastering, which leads to hangs on Loongson LS7A
- Add mechanism to prevent Max_Read_Request_Size (MRRS) increases,
again to avoid hardware issues on Loongson LS7A (and likely other
devices based on DesignWare IP)
- Ignore devices with a firmware (DT or ACPI) node that says the
device is disabled
Resource management:
- Distribute spare resources to unconfigured hotplug bridges at
boot-time (not just when hot-adding such a bridge), which makes
hot-adding devices to docks work better. Tried this in v6.1 but had
to revert for regressions, so try again
- Fix root bus issue that dropped resources that happened to end
at 0, e.g., [bus 00]
PCI device hotplug:
- Remove device locking when marking device as disconnected so this
doesn't have to wait for concurrent driver bind/unbind to complete
- Quirk more Qualcomm bridges that don't fully implement the PCIe
Slot Status 'Command Completed' bit
Power management:
- Account for _S0W of the target bridge in acpi_pci_bridge_d3() so we
don't miss hot-add notifications for USB4 docks, Thunderbolt, etc
Reset:
- Observe delay after reset, e.g., resuming from system sleep,
regardless of whether a bridge can suspend to D3cold at runtime
- Wait for secondary bus to become ready after a bridge reset
Virtualization:
- Avoid FLR on some AMD FCH AHCI adapters where it doesn't work
- Allow independent IOMMU groups for some Wangxun NICs that prevent
peer-to-peer transactions but don't advertise an ACS Capability
Error handling:
- Configure End-to-End-CRC (ECRC) only if Linux owns the AER
Capability
- Remove redundant Device Control Error Reporting Enable in the AER
service driver since this is already done for all devices during
enumeration
ASPM:
- Add pci_enable_link_state() interface to allow drivers to enable
ASPM link state
Endpoint framework:
- Move dra7xx and tegra194 linkup processing from hard IRQ to
threaded IRQ handler
- Add a separate lock for endpoint controller list of endpoint
function drivers to prevent deadlock in callbacks
- Pass events from endpoint controller to endpoint function drivers
via callbacks instead of notifiers
Synopsys DesignWare eDMA controller driver (acked by Vinod):
- Fix CPU vs PCI address issues
- Fix source vs destination address issues
- Fix issues with interleaved transfer semantics
- Fix channel count initialization issue (issue still exists in
several other drivers)
- Clean up and improve debugfs usage so it will work on platforms
with several eDMA devices
Baikal T-1 PCIe controller driver:
- Set a 64-bit DMA mask
Freescale i.MX6 PCIe controller driver:
- Add i.MX8MM, i.MX8MQ, i.MX8MP endpoint mode DT binding and driver
support
Intel VMD host bridge driver:
- Add quirk to configure PCIe ASPM and LTR. This is normally done by
BIOS, and will be for future products
Marvell MVEBU PCIe controller driver:
- Mark this driver as broken in Kconfig since bugs prevent its daily
usage
MediaTek MT7621 PCIe controller driver:
- Delay PHY port initialization to improve boot reliability for ZBT
WE1326, ZBT WF3526-P, and some Netgear models
Qualcomm PCIe controller driver:
- Add MSM8998 DT compatible string
- Unify MSM8996 and MSM8998 clock orderings
- Add SM8350 DT binding and driver support
- Add IPQ8074 Gen3 DT binding and driver support
- Correct qcom,perst-regs in DT binding
- Add qcom_pcie_host_deinit() so the PHY is powered off and
regulators and clocks are disabled on late host-init errors
Socionext UniPhier Pro5 controller driver:
- Clean up uniphier-ep reg, clocks, resets, and their names in DT
binding
Synopsys DesignWare PCIe controller driver:
- Restrict coherent DMA mask to 32 bits for MSI, but allow controller
drivers to set 64-bit streaming DMA mask
- Add eDMA engine support in both Root Port and Endpoint controllers
Miscellaneous:
- Remove MODULE_LICENSE from boolean drivers so they don't look like
modules so modprobe can complain about them"
* tag 'pci-v6.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (86 commits)
PCI: dwc: Add Root Port and Endpoint controller eDMA engine support
PCI: bt1: Set 64-bit DMA mask
PCI: dwc: Restrict only coherent DMA mask for MSI address allocation
dmaengine: dw-edma: Prepare dw_edma_probe() for builtin callers
dmaengine: dw-edma: Depend on DW_EDMA instead of selecting it
dmaengine: dw-edma: Add mem-mapped LL-entries support
PCI: Remove MODULE_LICENSE so boolean drivers don't look like modules
PCI: hv: Drop duplicate PCI_MSI dependency
PCI/P2PDMA: Annotate RCU dereference
PCI/sysfs: Constify struct kobj_type pci_slot_ktype
PCI: hotplug: Allow marking devices as disconnected during bind/unbind
PCI: pciehp: Add Qualcomm quirk for Command Completed erratum
PCI: qcom: Add IPQ8074 Gen3 port support
dt-bindings: PCI: qcom: Add IPQ8074 Gen3 port
dt-bindings: PCI: qcom: Sort compatibles alphabetically
PCI: qcom: Fix host-init error handling
PCI: qcom: Add SM8350 support
dt-bindings: PCI: qcom: Add SM8350
dt-bindings: PCI: qcom-ep: Correct qcom,perst-regs
dt-bindings: PCI: qcom: Unify MSM8996 and MSM8998 clock order
...
- Always observe reset delay when waking devices from D3cold, e.g., after
system sleep, regardless of whether we're allowed to runtime-suspend to
D3cold (Lukas Wunner)
- Unify reset and resume delays to wait for downstream devices after a
bridge reset (Lukas Wunner)
- Wait for downstream devices after a DPC-induced bridge reset (Lukas
Wunner)
* pci/reset:
PCI/DPC: Await readiness of secondary bus after reset
PCI: Unify delay handling for reset and resume
PCI/PM: Observe reset delay irrespective of bridge_d3
On surprise removal, pciehp_unconfigure_device() and acpiphp's
trim_stale_devices() call pci_dev_set_disconnected() to mark removed
devices as permanently offline. Thereby, the PCI core and drivers know
to skip device accesses.
However pci_dev_set_disconnected() takes the device_lock and thus waits for
a concurrent driver bind or unbind to complete. As a result, the driver's
->probe and ->remove hooks have no chance to learn that the device is gone.
That doesn't make any sense, so drop the device_lock and instead use atomic
xchg() and cmpxchg() operations to update the device state.
As a byproduct, an AB-BA deadlock reported by Anatoli is fixed which occurs
on surprise removal with AER concurrently performing a bus reset.
AER bus reset:
INFO: task irq/26-aerdrv:95 blocked for more than 120 seconds.
Tainted: G W 6.2.0-rc3-custom-norework-jan11+
schedule
rwsem_down_write_slowpath
down_write_nested
pciehp_reset_slot # acquires reset_lock
pci_reset_hotplug_slot
pci_slot_reset # acquires device_lock
pci_bus_error_reset
aer_root_reset
pcie_do_recovery
aer_process_err_devices
aer_isr
pciehp surprise removal:
INFO: task irq/26-pciehp:96 blocked for more than 120 seconds.
Tainted: G W 6.2.0-rc3-custom-norework-jan11+
schedule_preempt_disabled
__mutex_lock
mutex_lock_nested
pci_dev_set_disconnected # acquires device_lock
pci_walk_bus
pciehp_unconfigure_device
pciehp_disable_slot
pciehp_handle_presence_or_link_change
pciehp_ist # acquires reset_lock
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215590
Fixes: a6bd101b8f ("PCI: Unify device inaccessible")
Link: https://lore.kernel.org/r/3dc88ea82bdc0e37d9000e413d5ebce481cbd629.1674205689.git.lukas@wunner.de
Reported-by: Anatoli Antonovitch <anatoli.antonovitch@amd.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v4.20+
Cc: Keith Busch <kbusch@kernel.org>
This reverts commit 4ff116d0d5.
Tasev Nikola and Mark Enriquez reported that resume from suspend was broken
in v6.1-rc1. Tasev bisected to a47126ec29 ("PCI/PTM: Cache PTM
Capability offset"), but we can't figure out how that could be related.
Mark saw the same symptoms and bisected to 4ff116d0d5 ("PCI/ASPM: Save L1
PM Substates Capability for suspend/resume"), which does have a connection:
it restores L1 Substates configuration while ASPM L1 may be enabled:
pci_restore_state
pci_restore_aspm_l1ss_state
aspm_program_l1ss
pci_write_config_dword(PCI_L1SS_CTL1, ctl1) # L1SS restore
pci_restore_pcie_state
pcie_capability_write_word(PCI_EXP_LNKCTL, cap[i++]) # L1 restore
which is a problem because PCIe r6.0, sec 5.5.4, requires that:
If setting either or both of the enable bits for ASPM L1 PM
Substates, both ports must be configured as described in this
section while ASPM L1 is disabled.
Separately, Thomas Witt reported that 5e85eba6f5 ("PCI/ASPM: Refactor L1
PM Substates Control Register programming") broke suspend/resume, and it
depends on 4ff116d0d5.
Revert 4ff116d0d5 ("PCI/ASPM: Save L1 PM Substates Capability for
suspend/resume") to fix the resume issue and enable revert of 5e85eba6f5
to fix the issue Thomas reported.
Note that reverting 4ff116d0d5 means L1 Substates config may be lost on
suspend/resume. As far as we know the system will use more power but will
still *work* correctly.
Fixes: 4ff116d0d5 ("PCI/ASPM: Save L1 PM Substates Capability for suspend/resume")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216782
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216877
Reported-by: Tasev Nikola <tasev.stefanoska@skynet.be>
Reported-by: Mark Enriquez <enriquezmark36@gmail.com>
Reported-by: Thomas Witt <kernel@witt.link>
Tested-by: Mark Enriquez <enriquezmark36@gmail.com>
Tested-by: Thomas Witt <kernel@witt.link>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v6.1+
Cc: Vidya Sagar <vidyas@nvidia.com>
pci_bridge_wait_for_secondary_bus() is called after a Secondary Bus
Reset, but not after a DPC-induced Hot Reset.
As a result, the delays prescribed by PCIe r6.0 sec 6.6.1 are not
observed and devices on the secondary bus may be accessed before
they're ready.
One affected device is Intel's Ponte Vecchio HPC GPU. It comprises a
PCIe switch whose upstream port is not immediately ready after reset.
Because its config space is restored too early, it remains in
D0uninitialized, its subordinate devices remain inaccessible and DPC
recovery fails with messages such as:
i915 0000:8c:00.0: can't change power state from D3cold to D0 (config space inaccessible)
intel_vsec 0000:8e:00.1: can't change power state from D3cold to D0 (config space inaccessible)
pcieport 0000:89:02.0: AER: device recovery failed
Fix it.
Link: https://lore.kernel.org/r/9f5ff00e1593d8d9a4b452398b98aa14d23fca11.1673769517.git.lukas@wunner.de
Tested-by: Ravi Kishore Koppuravuri <ravi.kishore.koppuravuri@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Sheng Bi reports that pci_bridge_secondary_bus_reset() may fail to wait
for devices on the secondary bus to become accessible after reset:
Although it does call pci_dev_wait(), it erroneously passes the bridge's
pci_dev rather than that of a child. The bridge of course is always
accessible while its secondary bus is reset, so pci_dev_wait() returns
immediately.
Sheng Bi proposes introducing a new pci_bridge_secondary_bus_wait()
function which is called from pci_bridge_secondary_bus_reset():
https://lore.kernel.org/linux-pci/20220523171517.32407-1-windy.bi.enflame@gmail.com/
However we already have pci_bridge_wait_for_secondary_bus() which does
almost exactly what we need. So far it's only called on resume from
D3cold (which implies a Fundamental Reset per PCIe r6.0 sec 5.8).
Re-using it for Secondary Bus Resets is a leaner and more rational
approach than introducing a new function.
That only requires a few minor tweaks:
- Amend pci_bridge_wait_for_secondary_bus() to await accessibility of
the first device on the secondary bus by calling pci_dev_wait() after
performing the prescribed delays. pci_dev_wait() needs two parameters,
a reset reason and a timeout, which callers must now pass to
pci_bridge_wait_for_secondary_bus(). The timeout is 1 sec for resume
(PCIe r6.0 sec 6.6.1) and 60 sec for reset (commit 821cdad5c4 ("PCI:
Wait up to 60 seconds for device to become ready after FLR")).
Introduce a PCI_RESET_WAIT macro for the 1 sec timeout.
- Amend pci_bridge_wait_for_secondary_bus() to return 0 on success or
-ENOTTY on error for consumption by pci_bridge_secondary_bus_reset().
- Drop an unnecessary 1 sec delay from pci_reset_secondary_bus() which
is now performed by pci_bridge_wait_for_secondary_bus(). A static
delay this long is only necessary for Conventional PCI, so modern
PCIe systems benefit from shorter reset times as a side effect.
Fixes: 6b2f1351af ("PCI: Wait for device to become ready after secondary bus reset")
Link: https://lore.kernel.org/r/da77c92796b99ec568bd070cbe4725074a117038.1673769517.git.lukas@wunner.de
Reported-by: Sheng Bi <windy.bi.enflame@gmail.com>
Tested-by: Ravi Kishore Koppuravuri <ravi.kishore.koppuravuri@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: stable@vger.kernel.org # v4.17+
PCIe r2.0, sec 7.8 added Link Capabilities/Status/Control 2 registers to
the PCIe Capability with Capability Version 2.
Previously we assumed these registers were implemented for all PCIe
Capabilities of version 2 or greater, but in fact they are only
implemented for devices with Links.
Update pcie_capability_reg_implemented() to check whether the device has
a Link.
[bhelgaas: commit log, squash export]
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2209100057070.2275@angie.orcam.me.uk
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2209100057300.2275@angie.orcam.me.uk
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Add macros for PCI Configuration Mechanism #1 and use them in the
ftpci100, mt7621, and tegra drivers (Pali Rohár)
* remotes/lorenzo/pci/misc:
PCI: tegra: Use PCI_CONF1_EXT_ADDRESS() macro
PCI: mt7621: Use PCI_CONF1_EXT_ADDRESS() macro
PCI: ftpci100: Use PCI_CONF1_ADDRESS() macro
PCI: Add standard PCI Config Address macros
- Cache the PTM capability offset instead of searching for it every time
(Bjorn Helgaas)
- Separate PTM configuration from PTM enable (Bjorn Helgaas)
- Add pci_suspend_ptm() and pci_resume_ptm() to disable and re-enable PTM
on suspend/resume so some Root Ports can safely enter a lower-power PM
state (Bjorn Helgaas)
- Disable PTM for all devices during suspend; previously we only did this
for Root Ports and even then only in certain cases (Bjorn Helgaas)
- Simplify pci_pm_suspend_noirq() (Rajvi Jingar)
- Reduce the delay after transitions to/from D3hot by using usleep_range()
instead of msleep(), which reduces the typical delay from 19ms to 10ms
(Sajid Dalvi, Will McVicker)
* pci/pm:
PCI/PM: Reduce D3hot delay with usleep_range()
PCI/PM: Simplify pci_pm_suspend_noirq()
PCI/PM: Always disable PTM for all devices during suspend
PCI/PTM: Consolidate PTM interface declarations
PCI/PTM: Reorder functions in logical order
PCI/PTM: Preserve RsvdP bits in PTM Control register
PCI/PTM: Move pci_ptm_info() body into its only caller
PCI/PTM: Add pci_suspend_ptm() and pci_resume_ptm()
PCI/PTM: Separate configuration and enable
PCI/PTM: Add pci_upstream_ptm() helper
PCI/PTM: Cache PTM Capability offset
Previously the L1 PM Substates Control Registers (CTL1 and CTL2) weren't
saved and restored during suspend/resume leading to the L1 PM Substates
configuration being lost post-resume.
Save the L1 PM Substates Control Registers so that the configuration is
retained post-resume.
[bhelgaas: drop pci_is_pcie() testing; we can rely on pci_configure_ltr()
having already done that]
Link: https://lore.kernel.org/r/20220913131822.16557-3-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Lot of PCI and PCIe controllers are using standard Config Address for PCI
Configuration Mechanism #1 (as defined in PCI Local Bus Specification) or
its extended version.
So introduce new macros PCI_CONF1_ADDRESS() and PCI_CONF1_EXT_ADDRESS() in
include file drivers/pci/pci.h which can be suitable for PCI and PCIe
controllers which uses this type of access to PCI config space.
Link: https://lore.kernel.org/r/20220924092404.31776-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Consolidate all the PTM-related declarations in drivers/pci/pci.h. No
functional change intended.
Link: https://lore.kernel.org/r/20220909202505.314195-9-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We disable PTM during suspend because that allows some Root Ports to enter
lower-power PM states, which means we also need to disable PTM for all
downstream devices. Add pci_suspend_ptm() and pci_resume_ptm() for this
purpose.
pci_enable_ptm() and pci_disable_ptm() are for drivers to use to enable or
disable PTM. They use dev->ptm_enabled to keep track of whether PTM should
be enabled.
pci_suspend_ptm() and pci_resume_ptm() are PCI core-internal functions to
temporarily disable PTM during suspend and (depending on dev->ptm_enabled)
re-enable PTM during resume.
Enable/disable/suspend/resume all use internal __pci_enable_ptm() and
__pci_disable_ptm() functions that only update the PTM Control register.
Outline:
pci_enable_ptm(struct pci_dev *dev)
{
__pci_enable_ptm(dev);
dev->ptm_enabled = 1;
pci_ptm_info(dev);
}
pci_disable_ptm(struct pci_dev *dev)
{
if (dev->ptm_enabled) {
__pci_disable_ptm(dev);
dev->ptm_enabled = 0;
}
}
pci_suspend_ptm(struct pci_dev *dev)
{
if (dev->ptm_enabled)
__pci_disable_ptm(dev);
}
pci_resume_ptm(struct pci_dev *dev)
{
if (dev->ptm_enabled)
__pci_enable_ptm(dev);
}
Nothing currently calls pci_resume_ptm(); the suspend path saves the PTM
state before disabling PTM, so the PTM state restore in the resume path
implicitly re-enables it. A future change will use pci_resume_ptm() to fix
some problems with this approach.
Link: https://lore.kernel.org/r/20220909202505.314195-5-helgaas@kernel.org
Tested-by: Rajvi Jingar <rajvi.jingar@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
pcie_aspm_pm_state_change() was introduced at the inception of PCIe ASPM
code, but it can cause some issues. For instance, when ASPM config is
changed via sysfs, those changes won't persist across power state change
because pcie_aspm_pm_state_change() overwrites them.
Also, if the driver restores L1SS [1] after system resume, the restored
state will also be overwritten by pcie_aspm_pm_state_change().
Remove pcie_aspm_pm_state_change(). If there's any hardware that really
needs it to function, a quirk can be used instead.
[1] https://lore.kernel.org/linux-pci/20220201123536.12962-1-vidyas@nvidia.com/
Link: https://lore.kernel.org/r/20220509073639.2048236-1-kai.heng.feng@canonical.com
[bhelgaas: remove additional pcie_aspm_pm_state_change() call in
pci_set_low_power_state(), added by
10aa5377fc ("PCI/PM: Split pci_raw_set_power_state()") and moved by
7957d20145 ("PCI/PM: Relocate pci_set_low_power_state()")]
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add function of_pci_get_slot_power_limit(), which parses the
'slot-power-limit-milliwatt' DT property, returning the value in
milliwatts and in format ready for the PCIe Slot Capabilities Register.
Link: https://lore.kernel.org/r/20220412094946.27069-4-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----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=nsMh
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Conserve IRQs by setting up portdrv IRQs only when there are users
(Jan Kiszka)
- Rework and simplify _OSC negotiation for control of PCIe features
(Joerg Roedel)
- Remove struct pci_dev.driver pointer since it's redundant with the
struct device.driver pointer (Uwe Kleine-König)
Resource management:
- Coalesce contiguous host bridge apertures from _CRS to accommodate
BARs that cover more than one aperture (Kai-Heng Feng)
Sysfs:
- Check CAP_SYS_ADMIN before parsing user input (Krzysztof
Wilczyński)
- Return -EINVAL consistently from "store" functions (Krzysztof
Wilczyński)
- Use sysfs_emit() in endpoint "show" functions to avoid buffer
overruns (Kunihiko Hayashi)
PCIe native device hotplug:
- Ignore Link Down/Up caused by resets during error recovery so
endpoint drivers can remain bound to the device (Lukas Wunner)
Virtualization:
- Avoid bus resets on Atheros QCA6174, where they hang the device
(Ingmar Klein)
- Work around Pericom PI7C9X2G switch packet drop erratum by using
store and forward mode instead of cut-through (Nathan Rossi)
- Avoid trying to enable AtomicOps on VFs; the PF setting applies to
all VFs (Selvin Xavier)
MSI:
- Document that /sys/bus/pci/devices/.../irq contains the legacy INTx
interrupt or the IRQ of the first MSI (not MSI-X) vector (Barry
Song)
VPD:
- Add pci_read_vpd_any() and pci_write_vpd_any() to access anywhere
in the possible VPD space; use these to simplify the cxgb3 driver
(Heiner Kallweit)
Peer-to-peer DMA:
- Add (not subtract) the bus offset when calculating DMA address
(Wang Lu)
ASPM:
- Re-enable LTR at Downstream Ports so they don't report Unsupported
Requests when reset or hot-added devices send LTR messages
(Mingchuang Qiao)
Apple PCIe controller driver:
- Add driver for Apple M1 PCIe controller (Alyssa Rosenzweig, Marc
Zyngier)
Cadence PCIe controller driver:
- Return success when probe succeeds instead of falling into error
path (Li Chen)
HiSilicon Kirin PCIe controller driver:
- Reorganize PHY logic and add support for external PHY drivers
(Mauro Carvalho Chehab)
- Support PERST# GPIOs for HiKey970 external PEX 8606 bridge (Mauro
Carvalho Chehab)
- Add Kirin 970 support (Mauro Carvalho Chehab)
- Make driver removable (Mauro Carvalho Chehab)
Intel VMD host bridge driver:
- If IOMMU supports interrupt remapping, leave VMD MSI-X remapping
enabled (Adrian Huang)
- Number each controller so we can tell them apart in
/proc/interrupts (Chunguang Xu)
- Avoid building on UML because VMD depends on x86 bare metal APIs
(Johannes Berg)
Marvell Aardvark PCIe controller driver:
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek
Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits
(Marek Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits
at startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge"
instead of the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement
this per spec (Pali Rohár)
MediaTek MT7621 PCIe controller driver:
- Add MediaTek MT7621 PCIe host controller driver and DT binding
(Sergio Paracuellos)
Qualcomm PCIe controller driver:
- Add SC8180x compatible string (Bjorn Andersson)
- Add endpoint controller driver and DT binding (Manivannan
Sadhasivam)
- Restructure to use of_device_get_match_data() (Prasad Malisetty)
- Add SC7280-specific pcie_1_pipe_clk_src handling (Prasad Malisetty)
Renesas R-Car PCIe controller driver:
- Remove unnecessary includes (Geert Uytterhoeven)
Rockchip DesignWare PCIe controller driver:
- Add DT binding (Simon Xue)
Socionext UniPhier Pro5 controller driver:
- Serialize INTx masking/unmasking (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Run dwc .host_init() method before registering MSI interrupt
handler so we can deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Clean up Kconfig dependencies (Andy Shevchenko)
- Export symbols to allow more modular drivers (Luca Ceresoli)
TI DRA7xx PCIe controller driver:
- Allow host and endpoint drivers to be modules (Luca Ceresoli)
- Enable external clock if present (Luca Ceresoli)
TI J721E PCIe driver:
- Disable PHY when probe fails after initializing it (Christophe
JAILLET)
MicroSemi Switchtec management driver:
- Return error to application when command execution fails because an
out-of-band reset has cleared the device BARs, Memory Space Enable,
etc (Kelvin Cao)
- Fix MRPC error status handling issue (Kelvin Cao)
- Mask out other bits when reading of management VEP instance ID
(Kelvin Cao)
- Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions
(Kelvin Cao)
- Add check of event support (Logan Gunthorpe)
Miscellaneous:
- Remove unused pci_pool wrappers, which have been replaced by
dma_pool (Cai Huoqing)
- Use 'unsigned int' instead of bare 'unsigned' (Krzysztof
Wilczyński)
- Use kstrtobool() directly, sans strtobool() wrapper (Krzysztof
Wilczyński)
- Fix some sscanf(), sprintf() format mismatches (Krzysztof
Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof
Wilczyński)
- Correct some misspellings (Krzysztof Wilczyński)"
* tag 'pci-v5.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (137 commits)
PCI: Add ACS quirk for Pericom PI7C9X2G switches
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
PCI: Do not enable AtomicOps on VFs
...
Per PCIe r5.0, sec 7.5.3.16, Downstream Ports must disable LTR if the link
goes down (the Port goes DL_Down status). This is a problem because the
Downstream Port's dev->ltr_path is still set, so we think LTR is still
enabled, and we enable LTR in the Endpoint. When it sends LTR messages,
they cause Unsupported Request errors at the Downstream Port.
This happens in the reset path, where we may enable LTR in
pci_restore_pcie_state() even though the Downstream Port disabled LTR
because the reset caused a link down event.
It also happens in the hot-remove and hot-add path, where we may enable LTR
in pci_configure_ltr() even though the Downstream Port disabled LTR when
the hot-remove took the link down.
In these two scenarios, check the upstream bridge and restore its LTR
enable if appropriate.
The Unsupported Request may be logged by AER as follows:
pcieport 0000:00:1d.0: AER: Uncorrected (Non-Fatal) error received: id=00e8
pcieport 0000:00:1d.0: PCIe Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, id=00e8(Requester ID)
pcieport 0000:00:1d.0: device [8086:9d18] error status/mask=00100000/00010000
pcieport 0000:00:1d.0: [20] Unsupported Request (First)
In addition, if LTR is not configured correctly, the link cannot enter the
L1.2 state, which prevents some machines from entering the S0ix low power
state.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20211012075614.54576-1-mingchuang.qiao@mediatek.com
Reported-by: Utkarsh H Patel <utkarsh.h.patel@intel.com>
Signed-off-by: Mingchuang Qiao <mingchuang.qiao@mediatek.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
After previous changes there are no more users of struct
pci_platform_pm_ops in the tree, so drop it along with all of the
remaining related code.
No functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Using struct pci_platform_pm_ops for ACPI adds unnecessary
indirection to the interactions between the PCI core and ACPI PM,
which is also subject to retpolines.
Moreover, it is not particularly clear from the current code that,
as far as PCI PM is concerned, "platform" really means just ACPI
except for the special casess when Intel MID PCI PM is used or when
ACPI support is disabled (through the kernel config or command line,
or because there are no usable ACPI tables on the system).
To address the above, rework the PCI PM code to invoke ACPI PM
functions directly as needed and drop the acpi_pci_platform_pm
object that is not necessary any more.
Accordingly, update some of the ACPI PM functions in question to do
extra checks in case the ACPI support is disabled (which previously
was taken care of by avoiding to set the pci_platform_ops pointer
in those cases).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
There are only two users of struct pci_platform_pm_ops in the tree,
one of which is Intel MID PM and the other one is ACPI. They are
mutually exclusive and the MID PM should take precedence when they
both are enabled, but whether or not this really is the case hinges
on the specific ordering of arch_initcall() calls made by them.
The struct pci_platform_pm_ops abstraction is not really necessary
for just these two users, but it adds complexity and overhead because
of retoplines involved in using all of the function pointers in there.
It also makes following the code a bit more difficult than it would
be otherwise.
Moreover, Intel MID PCI PM doesn't even implement the majority of the
function pointers in struct pci_platform_pm_ops in a meaningful way,
so switch over the PCI core to calling the relevant MID PM routines,
mid_pci_set_power_state() and mid_pci_set_power_state(), directly as
needed and drop mid_pci_platform_pm.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Ferry Toth <fntoth@gmail.com>
Make pci_enable_ptm() accessible from the drivers.
Exposing this to the driver enables the driver to use the
'ptm_enabled' field of 'pci_dev' to check if PTM is enabled or not.
This reverts commit ac6c26da29 ("PCI: Make pci_enable_ptm() private").
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Interfaces and structs for saving and restoring PCI Capability state were
declared in include/linux/pci.h, but aren't needed outside drivers/pci/.
Move these to drivers/pci/pci.h:
struct pci_cap_saved_data
struct pci_cap_saved_state
void pci_allocate_cap_save_buffers()
void pci_free_cap_save_buffers()
int pci_add_cap_save_buffer()
int pci_add_ext_cap_save_buffer()
struct pci_cap_saved_state *pci_find_saved_cap()
struct pci_cap_saved_state *pci_find_saved_ext_cap()
Link: https://lore.kernel.org/r/20210802221728.1469304-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Change the type of probe argument in functions which implement reset
methods from int to bool to make the context and intent clear.
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Link: https://lore.kernel.org/r/20210817180500.1253-10-ameynarkhede03@gmail.com
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
_RST is a standard ACPI method that performs a function level reset of a
device (ACPI v6.3, sec 7.3.25).
Add pci_dev_acpi_reset() to probe for _RST method and execute if present.
The default priority of this reset is set to below device-specific and
above hardware resets.
Suggested-by: Alex Williamson <alex.williamson@redhat.com>
Link: https://lore.kernel.org/r/20210817180500.1253-9-ameynarkhede03@gmail.com
Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Move the existing logic from acpi_pci_bridge_d3() to a separate function
pci_set_acpi_fwnode() to set the ACPI fwnode. No functional change
intended.
Link: https://lore.kernel.org/r/20210817180500.1253-7-ameynarkhede03@gmail.com
Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Add "reset_method" sysfs attribute to enable user to query and set
preferred device reset methods and their ordering.
[bhelgaas: on invalid sysfs input, return error and preserve previous
config, as in earlier patch versions]
Co-developed-by: Alex Williamson <alex.williamson@redhat.com>
Link: https://lore.kernel.org/r/20210817180500.1253-6-ameynarkhede03@gmail.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Add reset_methods[] in struct pci_dev to keep track of reset mechanisms
supported by the device and their ordering.
Refactor probing and reset functions to take advantage of calling
convention of reset functions.
Co-developed-by: Alex Williamson <alex.williamson@redhat.com>
Link: https://lore.kernel.org/r/20210817180500.1253-4-ameynarkhede03@gmail.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Downstream Port Containment (PCIe r5.0, sec. 6.2.10) disables the link upon
an error and attempts to re-enable it when instructed by the DPC driver.
A slot which is both DPC- and hotplug-capable is currently powered off by
pciehp once DPC is triggered (due to the link change) and powered back up
on successful recovery. That's undesirable, the slot should remain powered
so the hotplugged device remains bound to its driver. DPC notifies the
driver of the error and of successful recovery in pcie_do_recovery() and
the driver may then restore the device to working state.
Moreover, Sinan points out that turning off slot power by pciehp may foil
recovery by DPC: Power off/on is a cold reset concurrently to DPC's warm
reset. Sathyanarayanan reports extended delays or failure in link
retraining by DPC if pciehp brings down the slot.
Fix by detecting whether a Link Down event is caused by DPC and awaiting
recovery if so. On successful recovery, ignore both the Link Down and the
subsequent Link Up event.
Afterwards, check whether the link is down to detect surprise-removal or
another DPC event immediately after DPC recovery. Ensure that the
corresponding DLLSC event is not ignored by synthesizing it and invoking
irq_wake_thread() to trigger a re-run of pciehp_ist().
The IRQ threads of the hotplug and DPC drivers, pciehp_ist() and
dpc_handler(), race against each other. If pciehp is faster than DPC, it
will wait until DPC recovery completes.
Recovery consists of two steps: The first step (waiting for link
disablement) is recognizable by pciehp through a set DPC Trigger Status
bit. The second step (waiting for link retraining) is recognizable through
a newly introduced PCI_DPC_RECOVERING flag.
If DPC is faster than pciehp, neither of the two flags will be set and
pciehp may glean the recovery status from the new PCI_DPC_RECOVERED flag.
The flag is zero if DPC didn't occur at all, hence DLLSC events are not
ignored by default.
pciehp waits up to 4 seconds before assuming that DPC recovery failed and
bringing down the slot. This timeout is not taken from the spec (it
doesn't mandate one) but based on a report from Yicong Yang that DPC may
take a bit more than 3 seconds on HiSilicon's Kunpeng platform.
The timeout is necessary because the DPC Trigger Status bit may never
clear: On Root Ports which support RP Extensions for DPC, the DPC driver
polls the DPC RP Busy bit for up to 1 second before giving up on DPC
recovery. Without the timeout, pciehp would then wait indefinitely for DPC
to complete.
This commit draws inspiration from previous attempts to synchronize DPC
with pciehp:
By Sinan Kaya, August 2018:
https://lore.kernel.org/linux-pci/20180818065126.77912-1-okaya@kernel.org/
By Ethan Zhao, October 2020:
https://lore.kernel.org/linux-pci/20201007113158.48933-1-haifeng.zhao@intel.com/
By Kuppuswamy Sathyanarayanan, March 2021:
https://lore.kernel.org/linux-pci/59cb30f5e5ac6d65427ceaadf1012b2ba8dbf66c.1615606143.git.sathyanarayanan.kuppuswamy@linux.intel.com/
Link: https://lore.kernel.org/r/0be565d97438fe2a6d57354b3aa4e8626952a00b.1619857124.git.lukas@wunner.de
Reported-by: Sinan Kaya <okaya@kernel.org>
Reported-by: Ethan Zhao <haifeng.zhao@intel.com>
Reported-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Tested-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Tested-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <kbusch@kernel.org>
pci_init_capabilities() is the only caller and doesn't use the return
value. So let's change the return type to void.
Link: https://lore.kernel.org/r/663ec440-8375-1459-ddb4-98ea76e75917@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "label", "index", and "acpi_index" sysfs attributes show firmware label
information about the device. If the ACPI Device Name _DSM is implemented
for the device, we have:
label Device name (optional, may be null)
acpi_index Instance number (unique under \_SB scope)
When there is no ACPI _DSM and SMBIOS provides an Onboard Devices structure
for the device, we have:
label Reference Designation, e.g., a silkscreen label
index Device Type Instance
Previously these attributes were dynamically created either by
pci_bus_add_device() or the pci_sysfs_init() initcall, but since they don't
need to be created or removed dynamically, we can use a static attribute so
the device model takes care of addition and removal automatically.
Convert "label", "index", and "acpi_index" to static attributes.
Presence of the ACPI _DSM (device_has_acpi_name()) determines whether the
ACPI information (label, acpi_index) or the SMBIOS information (label,
index) is visible.
[bhelgaas: commit log, split to separate patch, add "pci_dev_" prefix]
Suggested-by: Oliver O'Halloran <oohall@gmail.com>
Link: https://lore.kernel.org/r/20210416205856.3234481-6-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "vpd" sysfs attribute allows access to Vital Product Data (VPD).
Previously it was dynamically created either by pci_bus_add_device() or the
pci_sysfs_init() initcall, but since it doesn't need to be created or
removed dynamically, we can use a static attribute so the device model
takes care of addition and removal automatically.
Convert "vpd" to a static attribute and use the .is_bin_visible() callback
to check whether the device supports VPD.
Remove pcie_vpd_create_sysfs_dev_files(),
pcie_vpd_remove_sysfs_dev_files(), pci_create_capabilities_sysfs(), and
pci_create_capabilities_sysfs(), which are no longer needed.
[bhelgaas: This is substantially the same as the earlier patch from Heiner
Kallweit <hkallweit1@gmail.com>. I included Krzysztof's change here so all
the "convert to static attribute" changes are together.]
[bhelgaas: rename to vpd_read()/vpd_write() and pci_dev_vpd_attr_group]
Suggested-by: Oliver O'Halloran <oohall@gmail.com>
Based-on: https://lore.kernel.org/r/7703024f-8882-9eec-a122-599871728a89@gmail.com
Based-on-patch-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/20210416205856.3234481-5-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
A typical cloud provider SR-IOV use case is to create many VFs for use by
guest VMs. The VFs may not be assigned to a VM until a customer requests a
VM of a certain size, e.g., number of CPUs. A VF may need MSI-X vectors
proportional to the number of CPUs in the VM, but there is no standard way
to change the number of MSI-X vectors supported by a VF.
Some Mellanox ConnectX devices support dynamic assignment of MSI-X vectors
to SR-IOV VFs. This can be done by the PF driver after VFs are enabled,
and it can be done without affecting VFs that are already in use. The
hardware supports a limited pool of MSI-X vectors that can be assigned to
the PF or to individual VFs. This is device-specific behavior that
requires support in the PF driver.
Add a read-only "sriov_vf_total_msix" sysfs file for the PF and a writable
"sriov_vf_msix_count" file for each VF. Management software may use these
to learn how many MSI-X vectors are available and to dynamically assign
them to VFs before the VFs are passed through to a VM.
If the PF driver implements the ->sriov_get_vf_total_msix() callback,
"sriov_vf_total_msix" contains the total number of MSI-X vectors available
for distribution among VFs.
If no driver is bound to the VF, writing "N" to "sriov_vf_msix_count" uses
the PF driver ->sriov_set_msix_vec_count() callback to assign "N" MSI-X
vectors to the VF. When a VF driver subsequently reads the MSI-X Message
Control register, it will see the new Table Size "N".
Link: https://lore.kernel.org/linux-pci/20210314124256.70253-2-leon@kernel.org
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Compile-testing these drivers is currently broken. Enabling it causes a
couple of build failures though:
drivers/pci/controller/pci-thunder-ecam.c:119:30: error: shift count >= width of type [-Werror,-Wshift-count-overflow]
drivers/pci/controller/pci-thunder-pem.c:54:2: error: implicit declaration of function 'writeq' [-Werror,-Wimplicit-function-declaration]
drivers/pci/controller/pci-thunder-pem.c:392:8: error: implicit declaration of function 'acpi_get_rc_resources' [-Werror,-Wimplicit-function-declaration]
Fix them with the obvious one-line changes.
Link: https://lore.kernel.org/r/20210308152501.2135937-2-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Robert Richter <rric@kernel.org>
- Save/restore Precision Time Measurement Capability for suspend/resume
(David E. Box)
- Disable PTM during suspend to save power (David E. Box)
* pci/ptm:
PCI: Disable PTM during suspend to save power
PCI/PTM: Save/restore Precision Time Measurement Capability for suspend/resume
- Disable MSI for broken Pericom PCIe-USB adapter (Andy Shevchenko)
- Move MSI/MSI-X init to msi.c (Bjorn Helgaas)
- Move MSI/MSI-X flags updaters to msi.c (Bjorn Helgaas)
- Warn if we assign 64-bit MSI address to device that only supports 32-bit
MSI (Vidya Sagar)
* pci/msi:
PCI/MSI: Set device flag indicating only 32-bit MSI support
PCI/MSI: Move MSI/MSI-X flags updaters to msi.c
PCI/MSI: Move MSI/MSI-X init to msi.c
PCI: Use predefined Pericom Vendor ID
PCI: Disable MSI for Pericom PCIe-USB adapter
- Stop writing AER Capability when we don't own it (Sean V Kelley)
- Bind RCEC devices to the Port driver (Qiuxu Zhuo)
- Cache the RCEC RA Capability offset (Sean V Kelley)
- Add pci_walk_bridge() (Sean V Kelley)
- Clear AER status only when we control AER (Sean V Kelley)
- Recover from RCEC AER errors (Sean V Kelley)
- Add pcie_link_rcec() to associate RCiEPs with RCECs (Sean V Kelley)
- Recover from RCiEP AER errors (Sean V Kelley)
- Add pcie_walk_rcec() for RCEC AER handling (Sean V Kelley)
- Add pcie_walk_rcec() for RCEC PME handling (Sean V Kelley)
- Add RCEC AER error injection support (Qiuxu Zhuo)
* pci/err:
PCI/AER: Add RCEC AER error injection support
PCI/PME: Add pcie_walk_rcec() to RCEC PME handling
PCI/AER: Add pcie_walk_rcec() to RCEC AER handling
PCI/ERR: Recover from RCiEP AER errors
PCI/ERR: Add pcie_link_rcec() to associate RCiEPs
PCI/ERR: Recover from RCEC AER errors
PCI/ERR: Clear AER status only when we control AER
PCI/ERR: Add pci_walk_bridge() to pcie_do_recovery()
PCI/ERR: Avoid negated conditional for clarity
PCI/ERR: Use "bridge" for clarity in pcie_do_recovery()
PCI/ERR: Simplify by computing pci_pcie_type() once
PCI/ERR: Simplify by using pci_upstream_bridge()
PCI/ERR: Rename reset_link() to reset_subordinates()
PCI/ERR: Cache RCEC EA Capability offset in pci_init_capabilities()
PCI/ERR: Bind RCEC devices to the Root Port driver
PCI/AER: Write AER Capability only when we control it
- Decode PCIe 64 GT/s link speed (Gustavo Pimentel)
- De-duplicate Device IDs in the driver dynamic IDs list (Zhenzhong Duan)
- Return u8 from pci_find_capability() and similar (Puranjay Mohan)
- Return u16 from pci_find_ext_capability() and similar (Bjorn Helgaas)
- Include both device and resource name in config space resources
(Alexander Lobakin)
- Fix ACPI companion lookup for device 0 on the root bus (Rafael J.
Wysocki)
* pci/enumeration:
PCI/ACPI: Fix companion lookup for device 0 on the root bus
PCI: Keep both device and resource name for config space remaps
PCI: Return u16 from pci_find_ext_capability() and similar
PCI: Return u8 from pci_find_capability() and similar
PCI: Avoid duplicate IDs in driver dynamic IDs list
PCI: Move pci_match_device() ahead of new_id_store()
PCI: Decode PCIe 64 GT/s link speed
There are systems (for example, Intel based mobile platforms since Coffee
Lake) where the power drawn while suspended can be significantly reduced by
disabling Precision Time Measurement (PTM) on PCIe root ports as this
allows the port to enter a lower-power PM state and the SoC to reach a
lower-power idle state. To save this power, disable the PTM feature on root
ports during pci_prepare_to_sleep() and pci_finish_runtime_suspend(). The
feature will be returned to its previous state during restore and error
recovery.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=209361
Link: https://lore.kernel.org/r/20201207223951.19667-2-david.e.box@linux.intel.com
Reported-by: Len Brown <len.brown@intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI subsystem does not currently save and restore the configuration
space for the Precision Time Measurement (PTM) Extended Capability leading
to the possibility of the feature returning disabled on S3 resume. This
has been observed on Intel Coffee Lake desktops. Add save/restore of the
PTM control register. This saves the PTM Enable, Root Select, and Effective
Granularity bits.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20201207223951.19667-1-david.e.box@linux.intel.com
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Root Complex Event Collectors (RCEC) appear as peers to Root Ports and also
have the AER capability. In addition, actions need to be taken for
associated RCiEPs. In such cases the RCECs will need to be walked in order
to find and act upon their respective RCiEPs.
Extend the existing ability to link the RCECs with a walking function
pcie_walk_rcec(). Add RCEC support to the current AER service driver and
attach the AER service driver to the RCEC device.
Co-developed-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Link: https://lore.kernel.org/r/20201121001036.8560-14-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Linus Torvalds