Add comments for the virtio_driver members that were not documented.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Allow extra context per descriptor. To avoid slow down for data path,
this disables use of indirect descriptors for this vq.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Some drivers can't support all features in all configurations. At the
moment we blindly set FEATURES_OK and later FAILED. Support this better
by adding a callback drivers can use to do some early checks.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
For XDP we will need to reset the queues to allow for buffer headroom
to be configured. In order to do this we need to essentially run the
freeze()/restore() code path. Unfortunately the locking requirements
between the freeze/restore and reset paths are different however so
we can not simply reuse the code.
This patch refactors the code path and adds a reset helper routine.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This leaves vring_new_virtqueue alone for compatbility, but it
adds two new improved APIs:
vring_create_virtqueue: Creates a virtqueue backed by automatically
allocated coherent memory. (Some day it this could be extended to
support non-coherent memory, too, if there ends up being a platform
on which it's worthwhile.)
__vring_new_virtqueue: Creates a virtqueue with a manually-specified
layout. This should allow mic_virtio to work much more cleanly.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
virtio_device_is_legacy_only is now unused, drop
it from core.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
bug which doesn't merit cc: stable.
All the exciting stuff went via MST this cycle.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=COY0
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"A balloon enhancement, and a minor race-on-module-unload theoretical
bug which doesn't merit cc: stable.
All the exciting stuff went via MST this cycle"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_balloon: free some memory from balloon on OOM
virtio_balloon: return the amount of freed memory from leak_balloon()
virtio_blk: fix race at module removal
virtio: Fix comment typo 'CONFIG_S_FAILED'
legacy_only flag is now unused, drop it from core.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
transports need to be able to detect legacy-only
devices (ATM balloon only) to use legacy path
to drive them.
Add a core API to do just that.
The implementation just blacklists balloon:
not too pretty, but let's not over-engineer.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
We have no plans to support virtio 1.0 in balloon driver. Add an
explicit flag to mark it legacy only.
This will be used by follow-up patches.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
virtio-blk has some legacy feature bits that modern drivers
must not negotiate, but are needed for old legacy hosts
(that e.g. don't support virtio-scsi).
Allow a separate legacy feature table for such cases.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
For virtio-1, we can theoretically have a more complex virtqueue
layout with avail and used buffers not on a contiguous memory area
with the descriptor table. For now, it's fine for a transport driver
to stay with the old layout: It needs, however, a way to access
the locations of the avail/used rings so it can register them with
the host.
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Change u32 to u64, and use BIT_ULL and 1ULL everywhere.
Note: transports are unchanged, and only set low 32 bit.
This guarantees that no transport sets e.g. VERSION_1
by mistake without proper support.
Based on patch by Rusty.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
It seemed like a good idea to use bitmap for features
in struct virtio_device, but it's actually a pain,
and seems to become even more painful when we get more
than 32 feature bits. Just change it to a u32 for now.
Based on patch by Rusty.
Suggested-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Without the VIRTIO_ prefix CONFIG_S_FAILED looks like a Kconfig macro.
So use that prefix here too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Defer config changed notifications that arrive during
probe/scan/freeze/restore.
This will allow drivers to set DRIVER_OK earlier, without worrying about
racing with config change interrupts.
This change will also benefit old hypervisors (before 2009)
that send interrupts without checking DRIVER_OK: previously,
the callback could race with driver-specific initialization.
This will also help simplify drivers.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (cosmetic changes)
This is in preparation to extending config changed event handling
in core.
Wrapping these in an API also seems to make for a cleaner code.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Replace duplicated code in all transports with a single wrapper in
virtio.c.
The only functional change is in virtio_mmio.c: if a buggy device sends
us an interrupt before driver is set, we previously returned IRQ_NONE,
now we return IRQ_HANDLED.
As this must not happen in practice, this does not look like a big deal.
See also commit 3fff0179e3
virtio-pci: do not oops on config change if driver not loaded.
for the original motivation behind the driver check.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Add new function virtqueue_is_broken(). Callers of virtqueue_get_buf()
should check for a broken queue.
Signed-off-by: Heinz Graalfs <graalfs@linux.vnet.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtqueue_{kick()/notify()} should exploit the new host notification API.
If the notify call returned with a negative value the host kick failed
(e.g. a kick triggered after a device was hot-unplugged). In this case
the virtqueue is set to 'broken' and false is returned, otherwise true.
Signed-off-by: Heinz Graalfs <graalfs@linux.vnet.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a9 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
This adds a way to check ring empty state after enable_cb outside any
locks. Will be used by virtio_net.
Note: there's room for more optimization: caller is likely to have a
memory barrier already, which means we might be able to get rid of a
barrier here. Deferring this optimization until we do some
benchmarking.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I dived into lguest again, reworking the pagetable code so we can move
the switcher page: our fixmaps sometimes take more than 2MB now...
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJRga7lAAoJENkgDmzRrbjx/yIQAKpqIBtxOJeYH3SY+Uoe7Cfp
toNYcpJEldvb0UcWN8M2cSZpHoxl1SUoq9djwcM29tcKa7EZAjHaGtb/Q1qMTDgv
+B3WAfiGU2pmXFxLAkbrlLNGnysy24JspqJQ5hcYV84EiBxQdZp+nCYgOphd+GMK
ww16vo9ya8jFjzt3GeRp/Heb3vEzV4Cp6BC3i0m8A3WNpEpbRb66pqXNk5o8ggJO
SxQOKSXmUM+0m+jKSul5xn3e2Ls2LOrZZ8/DIHA+gW66N4Zab7n2/j1Q9VRxb4lh
FqnR7KwgBX8OCh9IsBDqQYS7MohvMYge6eUdLtFrq84jvMleMEhrC8q9v2tucFUb
5t18CLwvyK7Gdg6UCKiZ7YSPcuURAILO16al9bh5IseeBDsuX+43VsvQoBmFn9k6
cLOVTZ6BlOmahK5PyRYFSvLa9Rxzr/05Mr7oYq9UgshD9io78dnqczFYIORF53rW
zD7C4HuTZfYJFfNd0wAJ0RfVXnf8QvDlMdo7zPC26DSXNWqj8OexCY0qqSWUB+2F
vcfJP6NkV4fZB8aawWIFUVwc64yqtt2uPVLa7ATZWqk16PgKrchGewmw3tiEwOgu
1l7xgffTRRUIJsqaCZoXdgw3yezcKRjuUBcOxL09lDAAhc+NxWNvzZBsKp66DwDk
yZQKn0OdXnuf0CeEOfFf
=1tYL
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio & lguest updates from Rusty Russell:
"Lots of virtio work which wasn't quite ready for last merge window.
Plus I dived into lguest again, reworking the pagetable code so we can
move the switcher page: our fixmaps sometimes take more than 2MB now..."
Ugh. Annoying conflicts with the tcm_vhost -> vhost_scsi rename.
Hopefully correctly resolved.
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (57 commits)
caif_virtio: Remove bouncing email addresses
lguest: improve code readability in lg_cpu_start.
virtio-net: fill only rx queues which are being used
lguest: map Switcher below fixmap.
lguest: cache last cpu we ran on.
lguest: map Switcher text whenever we allocate a new pagetable.
lguest: don't share Switcher PTE pages between guests.
lguest: expost switcher_pages array (as lg_switcher_pages).
lguest: extract shadow PTE walking / allocating.
lguest: make check_gpte et. al return bool.
lguest: assume Switcher text is a single page.
lguest: rename switcher_page to switcher_pages.
lguest: remove RESERVE_MEM constant.
lguest: check vaddr not pgd for Switcher protection.
lguest: prepare to make SWITCHER_ADDR a variable.
virtio: console: replace EMFILE with EBUSY for already-open port
virtio-scsi: reset virtqueue affinity when doing cpu hotplug
virtio-scsi: introduce multiqueue support
virtio-scsi: push vq lock/unlock into virtscsi_vq_done
virtio-scsi: pass struct virtio_scsi to virtqueue completion function
...
You can access it directly now, since 3.8: v3.7-rc1-13-g06ca287
'virtio: move queue_index and num_free fields into core struct
virtqueue.'
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are specialized versions of virtqueue_add_buf(), which cover
over 80% of cases and are far clearer.
In particular, the scatterlists passed to these functions don't have
to be clean (ie. we ignore end markers).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio_scsi can really use this, to avoid the current hack of copying
the whole sg array. Some other things get slightly neater, too.
This causes a slowdown in virtqueue_add_buf(), which is implemented as
a wrapper. This is addressed in the next patches.
for i in `seq 50`; do /usr/bin/time -f 'Wall time:%e' ./vringh_test --indirect --eventidx --parallel --fast-vringh; done 2>&1 | stats --trim-outliers:
Before:
Using CPUS 0 and 3
Guest: notified 0, pinged 39009-39063(39062)
Host: notified 39009-39063(39062), pinged 0
Wall time:1.700000-1.950000(1.723542)
After:
Using CPUS 0 and 3
Guest: notified 0, pinged 39062-39063(39063)
Host: notified 39062-39063(39063), pinged 0
Wall time:1.760000-2.220000(1.789167)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Reviewed-by: Asias He <asias@redhat.com>
Add wrappers for the host vrings to support loose
coupling between the virtio device and driver.
A new struct vringh_config_ops with the functions
find_vrhs() and del_vrhs() is added to the virtio_device
struct. This enables virtio drivers to manage virtio
host rings without detailed knowledge of how the
vrings are created and deleted.
The function vringh_notify() is added so vringh clients
can notify the other side that buffers are added to the
used-ring.
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (constified vringh_config)
Add helper macro for drivers that don't do anything
special in module init/exit.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
It is just a table of function pointers, make it const for cleanliness and security
reasons.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Add drv_to_virtio wrapper to get virtio_driver from device_driver.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Use dev_to_virtio wrapper in virtio to make code clearly.
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
They're generic concepts, so hoist them. This also avoids accessor
functions (though kept around for merge with DaveM's net tree).
This goes even further than Jason Wang's 17bb6d4088 patch
("virtio-ring: move queue_index to vring_virtqueue") which moved the
queue_index from the specific transport.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Instead of storing the queue index in transport-specific virtio structs,
this patch moves them to vring_virtqueue and introduces an helper to get
the value. This lets drivers simplify their management and tracing of
virtqueues.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch changes virtio-scsi to use a new virtio_driver->scan() callback
so that scsi_scan_host() can be properly invoked once virtio_dev_probe() has
set add_status(dev, VIRTIO_CONFIG_S_DRIVER_OK) to signal active virtio-ring
operation, instead of from within virtscsi_probe().
This fixes a bug where SCSI LUN scanning for both virtio-scsi-raw and
virtio-scsi/tcm_vhost setups was happening before VIRTIO_CONFIG_S_DRIVER_OK
had been set, causing VIRTIO_SCSI_S_BAD_TARGET to occur. This fixes a bug
with virtio-scsi/tcm_vhost where LUN scan was not detecting LUNs.
Tested with virtio-scsi-raw + virtio-scsi/tcm_vhost w/ IBLOCK on 3.5-rc2 code.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The thaw operation was used by the balloon driver, but after the last
commit there's no reason to have separate thaw and restore callbacks.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Handle thaw, restore and freeze notifications from the PM core. Expose
these to individual virtio drivers that can quiesce and resume vq
operations. For drivers not implementing the thaw() method, use the
restore method instead.
These functions also save device-specific data so that the device can be
put in pre-suspend state after resume, and disable and enable the PCI
device in the freeze and resume functions, respectively.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Based on patch by Christoph for virtio_blk speedup:
Split virtqueue_kick to be able to do the actual notification
outside the lock protecting the virtqueue. This patch was
originally done by Stefan Hajnoczi, but I can't find the
original one anymore and had to recreated it from memory.
Pointers to the original or corrections for the commit message
are welcome.
Stefan's patch was here:
a6d06644e3http://www.spinics.net/lists/linux-virtualization/msg14616.html
Third time's the charm!
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Remove wrapper functions. This makes the allocation type explicit in
all callers; I used GPF_KERNEL where it seemed obvious, left it at
GFP_ATOMIC otherwise.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The old documentation is left over from when we used a structure with
strategy pointers.
And move the documentation to the C file as per kernel practice.
Though I disagree...
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Add support for reporting ring sizes via ethtool -g to the virtio_net
driver.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an API that tells the other side that callbacks
should be delayed until a lot of work has been done.
Implement using the new event_idx feature.
Note: it might seem advantageous to let the drivers
ask for a callback after a specific capacity has
been reached. However, as a single head can
free many entries in the descriptor table,
we don't really have a clue about capacity
until get_buf is called. The API is the simplest
to implement at the moment, we'll see what kind of
hints drivers can pass when there's more than one
user of the feature.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Add an add_buf variant that gets gfp parameter. Use that
to allocate indirect buffers.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We have a single virtqueue_ops implementation,
and it seems unlikely we'll get another one
at this point. So let's remove an unnecessary
level of indirection: it would be very easy to
re-add it if another implementation surfaces.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Add inline functions that wrap vq->vq_ops-> calls
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This adds a new file for virtio 9P device. The file
contain details of the mount device name that should
be used to mount the 9P file system.
Ex: /sys/devices/virtio-pci/virtio1/mount_tag file now
contian the tag name to be used to mount the 9P file system.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
There's currently no way for a virtio driver to ask for unused
buffers, so it has to keep a list itself to reclaim them at shutdown.
This is redundant, since virtio_ring stores that information. So
add a new hook to do this.
Signed-off-by: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This API change means that virtio_net can tell how much capacity
remains for buffers. It's necessarily fuzzy, since
VIRTIO_RING_F_INDIRECT_DESC means we can fit any number of descriptors
in one, *if* we can kmalloc.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Dinesh Subhraveti <dineshs@us.ibm.com>
Cornelia Huck