If a session in X25_STATE_1 (Awaiting Call Accept) receives a call
request, the session will be closed (x25_disconnect), cause=0x01
(Number Busy) and diag=0x48 (Call Collision) will be set and a clear
request will be send.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several spots in the kernel perform a sequence like:
skb_queue_tail(&sk->s_receive_queue, skb);
sk->sk_data_ready(sk, skb->len);
But at the moment we place the SKB onto the socket receive queue it
can be consumed and freed up. So this skb->len access is potentially
to freed up memory.
Furthermore, the skb->len can be modified by the consumer so it is
possible that the value isn't accurate.
And finally, no actual implementation of this callback actually uses
the length argument. And since nobody actually cared about it's
value, lots of call sites pass arbitrary values in such as '0' and
even '1'.
So just remove the length argument from the callback, that way there
is no confusion whatsoever and all of these use-after-free cases get
fixed as a side effect.
Based upon a patch by Eric Dumazet and his suggestion to audit this
issue tree-wide.
Signed-off-by: David S. Miller <davem@davemloft.net>
use pr_<level> instead of printk(LEVEL)
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are multiple locations in the X.25 packet layer where a skb is
assumed to be of at least a certain size and that all its data is
currently available at skb->data. These assumptions are not checked,
hence buffer overreads may occur. Use pskb_may_pull to check these
minimal size assumptions and ensure that data is available at skb->data
when necessary, as well as use skb_copy_bits where needed.
Signed-off-by: Matthew Daley <mattjd@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Cc: stable <stable@kernel.org>
Acked-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
X.25 call user data is being copied in its entirety from incoming messages
without consideration to the size of the destination buffers, leading to
possible buffer overflows. Validate incoming call user data lengths before
these copies are performed.
It appears this issue was noticed some time ago, however nothing seemed to
come of it: see http://www.spinics.net/lists/linux-x25/msg00043.html and
commit 8db09f26f9.
Signed-off-by: Matthew Daley <mattjd@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Andrew Hendry <andrew.hendry@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the case labels the same indent as the switch.
git diff -w shows 80 column line reflowing.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally x25_parse_facilities returned
-1 for an error
0 meaning 0 length facilities
>0 the length of the facilities parsed.
5ef41308f9 ("x25: Prevent crashing when parsing bad X.25 facilities") introduced more
error checking in x25_parse_facilities however used 0 to indicate bad parsing
a6331d6f9a ("memory corruption in X.25 facilities parsing") followed this further for
DTE facilities, again using 0 for bad parsing.
The meaning of 0 got confused in the callers.
If the facilities are messed up we can't determine where the data starts.
So patch makes all parsing errors return -1 and ensures callers close and don't use the skb further.
Reported-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moves the x25 interrupt flag from char into bitfield.
Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is a patch to stop X.25 examining fields beyond the end of the packet.
For example, when a simple CALL ACCEPTED was received:
10 10 0f
x25_parse_facilities was attempting to decode the FACILITIES field, but this
packet contains no facilities field.
Signed-off-by: John Hughes <john@calva.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
If there is data, the unsigned skb->len is greater than 0.
rt.sigdigits is unsigned as well, so the test `>= 0' is
always true, the other part of the test catches wrapped
values.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
For the common, open coded 'skb->h.raw = skb->data' operation, so that we can
later turn skb->h.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple cases:
skb->h.raw = skb->data;
skb->h.raw = {skb_push|[__]skb_pull}()
The next ones will handle the slightly more "complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows use of the optional user facility to insert ITU-T
(http://www.itu.int/ITU-T/) specified DTE facilities in call set-up x25
packets. This feature is optional; no facilities will be added if the ioctl
is not used, and call setup packet remains the same as before.
If the ioctls provided by the patch are used, then a facility marker will be
added to the x25 packet header so that the called dte address extension
facility can be differentiated from other types of facilities (as described in
the ITU-T X.25 recommendation) that are also allowed in the x25 packet header.
Facility markers are made up of two octets, and may be present in the x25
packet headers of call-request, incoming call, call accepted, clear request,
and clear indication packets. The first of the two octets represents the
facility code field and is set to zero by this patch. The second octet of the
marker represents the facility parameter field and is set to 0x0F because the
marker will be inserted before ITU-T type DTE facilities.
Since according to ITU-T X.25 Recommendation X.25(10/96)- 7.1 "All networks
will support the facility markers with a facility parameter field set to all
ones or to 00001111", therefore this patch should work with all x.25 networks.
While there are many ITU-T DTE facilities, this patch implements only the
called and calling address extension, with placeholders in the
x25_dte_facilities structure for the rest of the facilities.
Testing:
This patch was tested using a cisco xot router connected on its serial ports
to an X.25 network, and on its lan ports to a host running an xotd daemon.
It is also possible to test this patch using an xotd daemon and an x25tap
patch, where the xotd daemons work back-to-back without actually using an x.25
network. See www.fyonne.net for details on how to do this.
Signed-off-by: Shaun Pereira <spereira@tusc.com.au>
Acked-by: Andrew Hendry <ahendry@tusc.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of places just needs the states, not even linux/tcp.h, where this
enum was, needs it.
This speeds up development of the refactorings as less sources are
rebuilt when things get moved from net/tcp.h.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Martin Schiller