devm_add_action_or_reset() is introduced as a helper function which
internally calls devm_add_action(). If devm_add_action() fails
then it will execute the action mentioned and return the error code.
This reduce source code size (avoid writing the action twice)
and reduce the likelyhood of bugs.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Update the formula to calculate temperature:
Currently, current TEMP is calculated as
average of val1 (is calculated by formula 1)
and val2 (is calculated by formula 2). But,
as description in HWM (chapter 10A.3.1.2 Normal Mode.)
If (TEMP_CODE < THCODE2[11:0]) CTEMP value should be val1.
If (TEMP_CODE > THCODE2[11:0]) CTEMP value should be val2.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Update the formula to calculate CTEMP:
Currently, the CTEMP is average of val1 (is calculated by
formula 1) and val2 (is calculated by formula 2). But,
as description in HWM (chapter 10A.3.1.1 Setting of Normal Mode)
If (STEMP < Tj_T) CTEMP value should be val1.
If (STEMP > Tj_T) CTEMP value should be val2.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
As evaluation of hardware team, temperature calculation formula
of M3-W is difference from all other SoCs as below:
- M3-W: Tj_1: 116 (so Tj_1 - Tj_3 = 157)
- Others: Tj_1: 126 (so Tj_1 - Tj_3 = 167)
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Currently after store trip points number in 'ret', it is overwritten
afterwards, this cause incorrect trip point number always be shown in
the debug information after register of each thermal zone.
This patch fix this issue by moving get of trip number to
end of thermal zone registration.
Fixes: 6269e9f790 ("thermal: rcar_gen3_thermal: Register hwmon sysfs interface")
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Currently IRQ remains enabled after .remove, later if device is probed,
IRQ is requested before .thermal_init, this may cause IRQ function be
called before device is initialized.
this patch disables interrupt in .remove, to ensure irq function
only be called after device is fully initialized.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Currently IRQF_SHARED type interrupt line is allocated, but it
is not appropriate, as the interrupt line isn't shared between
different devices, instead IRQF_ONESHOT is the proper type.
By changing interrupt type to IRQF_ONESHOT, now irq handler is
no longer needed, as clear of interrupt status can be done in
threaded interrupt context.
Because IRQF_ONESHOT type interrupt line is kept disabled until
the threaded handler has been run, so there is no need to protect
read/write of REG_GEN3_IRQSTR with lock.
Fixes: 7d4b269776 ("enable hardware interrupts for trip points")
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Fix setting value for IRQCTL register. We are setting the last 6 bits
of (IRQCTL) to be 1 (0x3f), this is only suitable for H3ES1.*, according
to Hardware manual values 1 are "setting prohibited" for Gen3.
Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Register the hwmon sysfs interface on R-Car Gen3 thermal driver to
align it with Gen2 driver. Use devm_add_action() to unregister the
hwmon interface automatically.
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: linux-renesas-soc@vger.kernel.org
To: linux-pm@vger.kernel.org
From: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Pull thermal SoC updates from Eduardo Valentin:
"Several new things coming up. Specifics:
- Rework of tsens and hisi thermal drivers
- OF-thermal now allows sharing multiple cooling devices on maps
- Added support for r8a7744 and R8A77970 on rcar thermal driver
- Added support for r8a774a1 on rcar_gen3 thermal driver
- New thermal driver stm32
- Fixes on multiple thermal drivers: of-thermal, imx, qoriq, armada,
qcom-spmi, rcar, da9062/61"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal: (41 commits)
thermal: da9062/61: Prevent hardware access during system suspend
thermal: rcar_thermal: Prevent doing work after unbind
thermal: rcar_thermal: Prevent hardware access during system suspend
thermal: rcar_gen3_thermal: add R8A77980 support
dt-bindings: thermal: rcar-gen3-thermal: document R8A77980 bindings
thermal: add stm32 thermal driver
dt-bindings: stm32-thermal: add binding documentation
thermal: rcar_thermal: add R8A77970 support
dt-bindings: thermal: rcar-thermal: document R8A77970 bindings
thermal: rcar_thermal: fix duplicate IRQ request
dt-bindings: thermal: rcar: Add device tree support for r8a7744
thermal/drivers/hisi: Add the dual clusters sensors for hi3660
thermal/drivers/hisi: Add more sensors channel
thermal/drivers/hisi: Remove pointless irq field
thermal/drivers/hisi: Use platform_get_irq_byname
thermal/drivers/hisi: Replace macro name with relevant sensor location
thermal/drivers/hisi: Add multiple sensors support
thermal/drivers/hisi: Prepare to support multiple sensors
thermal/drivers/hisi: Factor out the probe functions
thermal/drivers/hisi: Set the thermal zone private data to the sensor pointer
...
Add the R-Car V3H (R8A77980) SoC support to the R-Car gen3 thermal driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Change the upper limit to clamp the high temperature value to 120C when
setting trip points.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Due to hardware evaluation result,
Max temperature is changed from 96 to 116 degree Celsius.
Also, calculation formula and pseudo FUSE values are changed accordingly.
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
Signed-off-by: Hien Dang <hien.dang.eb@renesas.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The initialization sequence for H3 (r8a7795) ES1.x and ES2.0 is
different. H3 ES2.0 and later uses the same sequence as M3 (r8a7796)
ES1.0. Fix this by not looking at compatible strings and instead
defaulting to the r8a7796 initialization sequence and use
soc_device_match() to check for H3 ES1.x.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The thermal_zone_of_device_ops structure is only passed as the fourth
argument to devm_thermal_zone_of_sensor_register, which is declared
as const. Thus the thermal_zone_of_device_ops structure itself can
be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
To restore operation it's easiest to reinitialise all TSCs. In order to
do this the current trip window needs to be stored in the TSC structure
so that it can be restored upon resume.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The device match data needs to be accessible outside the probe function,
store it in the private data structure.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Enable hardware trip points by implementing the set_trips callback. The
thermal core will take care of setting the initial trip point window and
to update it once the driver reports a TSC has moved outside it.
The interrupt structure for this device is a bit odd. There is not a
dedicated IRQ for each TSC, instead the interrupts are shared between
all TSCs. IRQn is fired if the temp monitored in IRQTEMPn is reached in
any of the TSCs, example IRQ3 is fired if temperature in IRQTEMP3 is
reached in either TSC0, TSC1 or TSC2.
For this reason the usage of interrupts in this driver is an all-on or
all-off design. When an interrupt happens all TSCs are checked and all
thermal zones are updated. This could be refined to be more fine grained
but the thermal core takes care of only updating the thermal zones that
have left their trip point window.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Record how many TSCs are found in struct rcar_gen3_thermal_priv, this is
needed to be able to add hardware interrupts for trip points later. Also
add a check to make sure at least one TSC is found.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Move the check for a TSC resource before allocating memory for a new
TSC. If no TSC is found there is little point in allocating memory for
it.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
There is no point in protecting a register read with a lock. This is
most likely a leftover from when the driver was reworked before being
submitted for upstream.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
The .thermal_init needs to be delayed a short amount of time to allow
for the TEMP register to contain something useful. If it's not delayed
these warnings are common during boot:
thermal thermal_zone0: failed to read out thermal zone (-5)
thermal thermal_zone1: failed to read out thermal zone (-5)
thermal thermal_zone2: failed to read out thermal zone (-5)
The warnings are triggered by the first call to .get_temp() while the
TEMP register contains 0 and rcar_gen3_thermal_get_temp() returns -EIO
since a TEMP value of 0 will result in a temperature reading which is
out of specifications.
This should have been done in the initial commit which adds the driver
as the same issue was found and corrected for r8a7795.
Fixes: 564e73d283 ("thermal: rcar_gen3_thermal: Add R-Car Gen3 thermal driver")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Add support for R-Car Gen3 thermal sensors. Polling only for now,
interrupts will be added incrementally. Same goes for reading fuses.
This is documented already, but no hardware available for now.
Signed-off-by: Hien Dang <hien.dang.eb@renesas.com>
Signed-off-by: Thao Nguyen <thao.nguyen.yb@rvc.renesas.com>
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[Niklas: document and rework temperature calculation]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Fuqian Huang