Note that these 2 are register compatible and report the same superio id,
but they are 2 distinct chips / models!
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Thomas Faber <thfabba@gmx.de>
Tested-by: Alexey Sychev <owl@umail.ru>
Tested-by: Dieter Bloms <dieter@bloms.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Note that this patch also makes 2 changes to the code paths for the f71889fg
to keep the code unified between the 2 (for simplicities sake). Both of these
are harmless for then f71889fg:
1) The first change is to always set the FAN_PROG_SEL bit to 0. This influences
accesses to some banked fan / pwm registers. On the f71889fg no registers
which we use are banked. On the f71889ed however some more fan registers
have been banked including one which we use, by making the FAN_PROG_SEL bit
0, address 0x96 will point to the right register.
2) The second change is to see a FANx_TEMP_SEL value of 0 as pointing to
a PECI / AMDSI value, and thus disable our pwm related sysfs attr.
This is correct for the f71889ed and on the f71889fg 0 is a reserved
value, so we should never see it and if we do, disabling the pwm related
sysfs attr is a sane thing to do.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Thomas Greve <tg42@gmx.net>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Putting this check in its own switch case rather then in the switch case
for adding pwm auto point sysfs attr is cleaner. This is a preparation patch
for adding support for more different models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This is a preparation patch for adding support for more different models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Remove the temp2_type sysfs files for f8000 / f71858fg models,
this got in accidentally and is wrong as these models don't have a
Temperature Sensor Type Register at all.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Make the temp sysattr array for the standard models a 2d array, which allows
to use it for models with less temperatures too. This is a preparation
patch for adding support for more different models.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This is a preparation patch for adding support for more different models,
some of which have a sparse list of used voltage pins.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
The code for determining a sensort type for temp1 was based on me misreading
the datasheet, the tested registers do not determine what kind of sensor
is actually reported as temp1. Instead the enable / disable certain additional
digital sensor readouts throug PECI / AMDSI, etc. Independent of these settings
temp1 is still reading an external BJT or thermistor as configured by the
Temperature Sensor Type Register (0x6b).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Systems with NCT6775F reported temperature sensor labels for systems with
NCT6776F. This patch fixes the problem.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
NCT6776F and NCT6775F support debouncing the fan RPM signal. This can
help improve the stability of th RPM signal for some fans (Arctic cooling
fans for example).
This patch adds a module parameter fan_debounce, which when set to 1 enables
debounce for all fans that the chip supports.
Signed-off-by: Ian Dobson <i.dobson@planet-ian.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Since the fan speed value can be above 0xff, we can no longer use
that value to determine if the fan speed reading is valid. This
makes it difficult to manipulate the stored fan speed register value.
If we store rpm instead of the fan speed register value, we do not
need to correct it if the fan divisor value is changed, and the above
mentioned problem no longer exists.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
Some of the chips supported by this driver have 13 bit or 16 bit fan count
registers. This patch improves support for those registers, specifically for
NCT6775F. With the changes in this patch, fan speed is reported correctly even
if the fan divider is set to a low value, which results in a fan speed reading
above 0xff.
With this patch, the width of fan count registers is no longer used to determine
if the chip has fan divider register(s) or not. A dedicated flag is used instead
to determine if this is the case.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
This patch adds support for NCT6775F and NCT6776F to the w83627ehf driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Tested-by: Ian Dobson <i.dobson@planet-ian.com> (NCT6776F)
Tested-by: Zachary Marzec <zmarzec@gmail.com> (ASUS P8P67 PRO/NCT6776F)
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
If SmartFan IV mode was configured at startup, it should be possible
to re-enable it later on.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
For newer chips, several registers are banked and thus need to be 16 bit.
Also, register addresses change.
To prepare for those chips, convert affected register arrays to 16 bit,
and change access to those registers to array pointers in struct w83627ehf_data.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
Add support for 4th temperature sensor on W83677HG-B.
Display temperature labels on W83677HG-B to report temperature sources.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
Assume that each register is banked, and set the bank for each access.
Cache the bank number so it only needs to be set if it changes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
This cleanup fixes most of the checkpatch warnings and errors in the w83627ehf
driver. Remaining warnings and errors are left untouched on purpose to avoid
making the code less readable.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
This patch unifies temperature register access, and replaces simple_strtoXXX
with strict_strtoXXX throughout the driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ian Dobson <i.dobson@planet-ian.com>
Some fan control chips support a configuration register to set the number of
tachometer pulses per fan revolution. Add an ABI attribute to support this
configuration register.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
LTC4151 is High Voltage I2C Current and Voltage Monitor from Linear
Technology.
Signed-off-by: Per Dalen <per.dalen@appeartv.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
LINEAR16 data format is unsigned, not signed. Impact is that affected
attributes report negative values in the upper half of the supported
value range.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
PMBus only has one set of limit registers for up to three temperature sensors.
Thus, changing a limit for one of the temperature sensors affects limits for
other temperature sensors in the same page (and potentially multiple pages
depending on the chip implementation). To handle this situation, re-read all
temperature limit registers when updating sensor data. This way, all affected
temperature limits are updated whenever the limit for a single sensor is
changed.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Assumption so far was that PMBus devices would support TEMP2 and TEMP3 registers
only on page 0, and that only the TEMP1 register would be used/supported
on other pages.
Turns out that is not correct. UCD92xx devices support TEMP1 and TEMP2 on
page 0, and TEMP2 on other pages. So it is necessary to change the core code
such that it does not make a page based assumptions about temperature register
support.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
So far, it seemed like fans would either all be in page 0, or that
there would be one page per fan.
Turns out this was a wrong assumption. There is at least one PMBus
fan controller which supports three pages with four fans each.
Update code to handle this situation.
Reported-by: Greg Schnorr <gschnorr@cisco.com>
Tested-by: Greg Schnorr <gschnorr@cisco.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Greg Schnorr <gschnorr@cisco.com>
Some PMBus chips do not support the VOUT_MODE register. To make matters worse,
such chips may not return an error when reading the register either, but instead
return 0xff.
Check if the register exists using pmbus_check_byte_register() before reading
its value. In addition, validate the returned value and ignore it if it is 0xff
(which is invalid).
Reported-by: Greg Schnorr <gschnorr@cisco.com>
Tested-by: Greg Schnorr <gschnorr@cisco.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Greg Schnorr <gschnorr@cisco.com>
This driver adds support for hardware monitoring features of various PMBus
devices.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
EMC6D103S is similar to EMC6D103, only it does not support registers 62[5:7],
6D[0:7], and 6E[0:7]. Register respective sysfs attributes and update affected
registers for all other chips only.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
So far, the driver updates temp_auto_hyst and temp_auto_off if temp_auto_min changes.
This may cause problems if temp_auto_off was not configured before configuring
temp_auto_min, because one of the variables used (off_desired) is not initialized
in this case.
To simplify the code, and for consistency with other drivers, no longer update the delta
between "min" and "off" until the user sets the "off" value again.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
ADT7463 and ADT7468 optionally support VID5 instead of the standard +12V
measurement input. Use a boolean to identify the chip configuration instead of
hardcoding it several times.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This patch adds support for hardware monitoring of Lineage Compact Power Line
Power Entry Modules.
Reviewed-by: Tom Grennan <tom.grennan@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
There is a move to deprecate bus-specific PM operations and move to
using dev_pm_ops instead in order to reduce the amount of boilerplate
code in buses and facilitiate updates to the PM core. Do this move for
the lis3lv02d SPI driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch initializes register CONFIG3 to a reasonable default PWM frequency
of 25kHz, to prevent audible sound in fan.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-mn10300:
MN10300: atomic_read() should ensure it emits a load
MN10300: The SMP_ICACHE_INV_FLUSH_RANGE IPI command does not exist
MN10300: Proper use of macros get_user() in the case of incremented pointers
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (26 commits)
MIPS: Alchemy: Fix reset for MTX-1 and XXS1500
MIPS: MTX-1: Make au1000_eth probe all PHY addresses
MIPS: Jz4740: Add HAVE_CLK
MIPS: Move idle task creation to work queue
MIPS, Perf-events: Use unsigned delta for right shift in event update
MIPS, Perf-events: Work with the new callchain interface
MIPS, Perf-events: Fix event check in validate_event()
MIPS, Perf-events: Work with the new PMU interface
MIPS, Perf-events: Work with irq_work
MIPS: Fix always CONFIG_LOONGSON_UART_BASE=y
MIPS: Loongson: Fix potentially wrong string handling
MIPS: Fix GCC-4.6 'set but not used' warning in arch/mips/mm/init.c
MIPS: Fix GCC-4.6 'set but not used' warning in ieee754int.h
MIPS: Remove unused code from arch/mips/kernel/syscall.c
MIPS: Fix GCC-4.6 'set but not used' warning in signal*.c
MIPS: MSP: Fix MSP71xx bpci interrupt handler return value
MIPS: Select R4K timer lib for all MSP platforms
MIPS: Loongson: Remove ad-hoc cmdline default
MIPS: Clear the correct flag in sysmips(MIPS_FIXADE, ...).
MIPS: Add an unreachable return statement to satisfy buggy GCCs.
...
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: ce4100: Set pci ops via callback instead of module init
x86/mm: Fix pgd_lock deadlock
x86/mm: Handle mm_fault_error() in kernel space
x86: Don't check for BIOS corruption in first 64K when there's no need to
This reverts the parent commit. I hate doing that, but it's generating
some discussion ("half of it is right"), and since I am planning on
doing the 2.6.38 release later today we can punt it to stable if
required. Let's not rock the boat right now.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
oom_kill_process() starts with victim_points == 0. This means that
(most likely) any child has more points and can be killed erroneously.
Also, "children has a different mm" doesn't match the reality, we should
check child->mm != t->mm. This check is not exactly correct if t->mm ==
NULL but this doesn't really matter, oom_kill_task() will kill them
anyway.
Note: "Kill all processes sharing p->mm" in oom_kill_task() is wrong
too.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit 32fd6901 (MIPS: Alchemy: get rid of common/reset.c)
Alchemy-based boards use their own reset function. For MTX-1 and XXS1500,
the reset function pokes at the BCSR.SYSTEM_RESET register, but this does
not work. According to Bruno Randolf, this was not tested when written.
Previously, the generic au1000_restart() routine called the board specific
reset function, which for MTX-1 and XXS1500 did not work, but finally made
a jump to the reset vector, which really triggers a system restart. Fix
reboot for both targets by jumping to the reset vector.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2093/
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When au1000_eth probes the MII bus for PHY address, if we do not set
au1000_eth platform data's phy_search_highest_address, the MII probing
logic will exit early and will assume a valid PHY is found at address 0.
For MTX-1, the PHY is at address 31, and without this patch, the link
detection/speed/duplex would not work correctly.
CC: stable@kernel.org
Signed-off-by: Florian Fainelli <florian@openwrt.org>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2111/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Hans de Goede