Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better reflect
the fact that this is not the GPIO struct device abstraction. We will
add that soon so this would be totallt confusing.
- It was noted that the driver .get_value() callbacks was
sometimes reporting negative -ERR values to the gpiolib core, expecting
them to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than zero"
to indicate that a line was active. As some would have bit 31 set to
indicate "line active" it clashed with negative error codes. This is
fixed by the largeish series clamping values in all drivers with
!!value to [0,1] and then augmenting the code to propagate error codes
to consumers. (Includes some ACKed patches in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of() design
pattern is indeed very nice, but we want to reform the struct gpio_chip
to be a non-volative, stateless business, and keep states internal to
the gpiolib to be able to hold on to the state when adding a proper
userspace ABI (character device) further down the road. To achieve this,
drivers need a handle at the internal state that is not dependent on
their struct gpio_chip() so we add gpiochip_add_data() and
gpiochip_get_data() following the pattern of many other subsystems.
All the "use gpiochip data pointer" patches transforms drivers to this
scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that removed.
Instead of having a separate mm_gpio_chip struct for these generic
drivers, merge that into struct gpio_chip, simplifying the code and
removing the need for separate and confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from the
OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
the branch is merged here too to account for infrastructural changes).
- The sx150x driver now supports the sx1502.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=63rR
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
Pull input updates from Dmitry Torokhov:
- new driver for eGalaxTouch serial touchscreen
- new driver for TS-4800 touchscreen
- an update for Goodix touchscreen driver
- PS/2 mouse module was reworked to limit number of protocols we try on
pass-through ports to speed up their detection time
- wacom_w8001 touchscreen driver now reports pen and touch via separate
instances of input devices
- other driver changes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (42 commits)
Input: elantech - mark protocols v2 and v3 as semi-mt
Input: wacom_w8001 - drop use of ABS_MT_TOOL_TYPE
Input: gpio-keys - fix check for disabling unsupported keys
Input: omap-keypad - remove dead check
Input: ti_am335x_tsc - fix HWPEN interrupt handling
Input: omap-keypad - set tasklet data earlier
Input: rohm_bu21023 - fix handling of retrying firmware update
Input: ALPS - report v3 pinnacle trackstick device only if is present
Input: ALPS - detect trackstick presence for v7 protocol
Input: pcap_ts - use to_delayed_work
Input: bma150 - constify bma150_cfg structure
Input: i8042 - add Fujitsu Lifebook U745 to the nomux list
Input: egalax_ts_serial - fix potential NULL dereference on error
Input: uinput - sanity check on ff_effects_max and EV_FF
Input: uinput - rework ABS validation
Input: uinput - add new UINPUT_DEV_SETUP and UI_ABS_SETUP ioctl
Input: goodix - use "inverted_[xy]" flags instead of "rotated_screen"
Input: goodix - add axis swapping and axis inversion support
Input: goodix - use goodix_i2c_write_u8 instead of i2c_master_send
Input: goodix - add power management support
...
Here's the big set of char/misc patches for 4.5-rc1.
Nothing major, lots of different driver subsystem updates, full details
in the shortlog. All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlaV0GsACgkQMUfUDdst+ymlPgCg07GSc4SOWlUL2V36vQ0kucoO
YjAAoMfeUEhsf/NJ7iaAMGQVUQKuYVqr
=BlqH
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here's the big set of char/misc patches for 4.5-rc1.
Nothing major, lots of different driver subsystem updates, full
details in the shortlog. All of these have been in linux-next for a
while"
* tag 'char-misc-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (71 commits)
mei: fix fasync return value on error
parport: avoid assignment in if
parport: remove unneeded space
parport: change style of NULL comparison
parport: remove unnecessary out of memory message
parport: remove braces
parport: quoted strings should not be split
parport: code indent should use tabs
parport: fix coding style
parport: EXPORT_SYMBOL should follow function
parport: remove trailing white space
parport: fix a trivial typo
coresight: Fix a typo in Kconfig
coresight: checking for NULL string in coresight_name_match()
Drivers: hv: vmbus: Treat Fibre Channel devices as performance critical
Drivers: hv: utils: fix hvt_op_poll() return value on transport destroy
Drivers: hv: vmbus: fix the building warning with hyperv-keyboard
extcon: add Maxim MAX3355 driver
Drivers: hv: ring_buffer: eliminate hv_ringbuffer_peek()
Drivers: hv: remove code duplication between vmbus_recvpacket()/vmbus_recvpacket_raw()
...
When using a protocol v2 or v3 hardware, elantech uses the function
elantech_report_semi_mt_data() to report data. This devices are rather
creepy because if num_finger is 3, (x2,y2) is (0,0). Yes, only one valid
touch is reported.
Anyway, userspace (libinput) is now confused by these (0,0) touches,
and detect them as palm, and rejects them.
Commit 3c0213d17a ("Input: elantech - fix semi-mt protocol for v3 HW")
was sufficient enough for xf86-input-synaptics and libinput before it has
palm rejection. Now we need to actually tell libinput that this device is
a semi-mt one and it should not rely on the actual values of the 2 touches.
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
* patchwork: (204 commits)
[media] rc: sunxi-cir: Initialize the spinlock properly
[media] rtl2832: do not filter out slave TS null packets
[media] rtl2832: print reg number on error case
[media] rtl28xxu: return demod reg page from driver cache
[media] coda: enable MPEG-2 ES decoding
[media] coda: don't start streaming without queued buffers
[media] coda: hook up vidioc_prepare_buf
[media] coda: relax coda_jpeg_check_buffer for trailing bytes
[media] coda: make to_coda_video_device static
[media] s5p-mfc: remove volatile attribute from MFC register addresses
[media] s5p-mfc: merge together s5p_mfc_hw_call and s5p_mfc_hw_call_void
[media] s5p-mfc: use spinlock to protect MFC context
[media] s5p-mfc: remove unnecessary callbacks
[media] s5p-mfc: make queue cleanup code common
[media] s5p-mfc: use one implementation of s5p_mfc_get_new_ctx
[media] s5p-mfc: constify s5p_mfc_codec_ops structures
[media] au8522: Avoid memory leak for device config data
[media] ir-lirc-codec.c: don't leak lirc->drv-rbuf
[media] uvcvideo: small cleanup in uvc_video_clock_update()
[media] uvcvideo: Fix reading the current exposure value of UVC
...
As of e0361b7017 ("Input: wacom_w8001 - split the touch and pen devices
into two devices") the touch events aren't multiplexed over the same device
anymore, the use of ABS_MT_TOOL_TYPE is superfluous. And even before then
it only ever sent MT_TOOL_TYPE_FINGER anyway.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 4ea14a53d8 ("Input: gpio-keys - report
error when disabling unsupported key") tried let user know that they
attempted to disable an unsupported key, unfortunately the check is wrong
as it believes that all codes are invalid. Fix it by ensuring that keys
that we try to disable are subset of keys (or switches) that device
reports.
Fixes: 4ea14a53d8 ("Input: gpio-keys - report error when disabling unsupported key")
Reported-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit da1f026b53 ("Keyboard: omap-keypad:
use matrix_keypad.h") switched the driver to use matrix keypad
infrastructure, which made array of keycodes to be unsigned short, and
caused the test for negativity never trigger. This leads to the following
static checker warning:
drivers/input/keyboard/omap-keypad.c:158 omap_kp_tasklet()
warn: 'keycodes[]' is never negative.
Given that we did not care about this check for a few years already let's
simply remove it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Remove write to REG_IRQCLR and REG_IRQWAKEUP in interrupt handler for
IRQENB_HW_PEN as the resume handler should and does clear REG_IRQWAKEUP.
IRQENB_HW_PEN bit is set in irqclr so that all interrupts get cleared
later so let IRQENB_HW_PEN be cleared by that.
Without this patch wakeup events from TSC_ADC do not work because pending
interrupts in TSC_ADC were causing HW_PEN interrupt, needed for wake from
suspend modes, to get disabled immediately by IRQ handler after being
enabled and preventing wake from happening.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It feels like we should set the tasklet data before enabling it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Because of the wrong condition we'd never retry firmware update.
Acked-by: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch moves v3 pinnacle code for trackstick detection from
alps_hw_init_v3() to alps_set_protocol() so ALPS_DUALPOINT flag can be
cleared before registering trackstick input device in kernel.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds detection of trackstick for v7 protocol devices. Code in
this patch is used in official Dell touchpad linux drivers for Dell models:
Dell Latitude E5250/5250, E5450/5450, E5550/5550
Detection code and base reg for alps v3 rushmore and v7 devices is exacly
same.
Also user in bug https://bugzilla.kernel.org/show_bug.cgi?id=94801 reported
that Toshiba Sattellite Z30-A-1DG has only alps v7 touchpad device without
trackstick and kernel reports to userspace also redundant trackstick
device.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use to_delayed_work() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The bma150_cfg structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Without i8042.nomux=1 the Elantech touch pad is not working at all on
a Fujitsu Lifebook U745. This patch does not seem necessary for all
U745 (maybe because of different BIOS versions?). However, it was
verified that the patch does not break those (see opensuse bug 883192:
https://bugzilla.opensuse.org/show_bug.cgi?id=883192).
Signed-off-by: Aurélien Francillon <aurelien@francillon.net>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
With the recent change af3ff643ea
(Drivers: hv: vmbus: Use uuid_le type consistently), we always get this
warning:
CC [M] drivers/input/serio/hyperv-keyboard.o
drivers/input/serio/hyperv-keyboard.c:427:2: warning: missing braces around
initializer [-Wmissing-braces]
{ HV_KBD_GUID, },
^
drivers/input/serio/hyperv-keyboard.c:427:2: warning: (near initialization
for .id_table[0].guid.b.) [-Wmissing-braces]
The patch fixes the warning.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We didn't check input_allocate_device() for failures so it could lead to
a NULL deref.
Fixes: 6b0f8f9c52 ('Input: add eGalaxTouch serial touchscreen driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently the user can set ff_effects_max to zero with the EV_FF bit (and
the FF_GAIN and/or FF_AUTOCENTER bits) set, in this case the uninitialized
methods ff->set_gain and/or ff->set_autocenter can be dereferenced,
resulting in a kernel oops.
Check in uinput_create_device() and print a helpful message and return
-EINVAL in case the check fails.
Signed-off-by: Elias Vanderstuyft <elias.vds@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rework the uinput ABS validation to check passed absinfo data immediately,
but do ABS initialization as last step in UI_DEV_CREATE. The behavior
observed by user-space is not changed, as ABS initialization was never
checked for errors.
With this in place, the order of device initialization and abs
configuration is no longer fixed. Userspace can initialize the device and
afterwards set absinfo just fine.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds two new ioctls, UINPUT_DEV_SETUP and UI_ABS_SETUP, that replaces
the old device setup method (by write()'ing "struct uinput_user_dev" to the
node). The old method is not easily extendable and requires huge payloads.
Furthermore, overloading write() without properly versioned objects is
error-prone.
Therefore, we introduce two new ioctls to replace the old method. These
ioctls support all features of the old method, plus a "resolution" field
for absinfo. Furthermore, it's properly forward-compatible to new ABS codes
and a growing "struct input_absinfo" structure.
UI_ABS_SETUP also allows user-space to skip unknown axes if not set. There
is no need to copy the whole array temporarily into the kernel, but instead
the caller issues several ioctl where we copy each value manually.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When sending "SLEEP" command to the controller it ceases scanning
completely and is unable to wake the system up from sleep, so if it is
configured as a wakeup source we should simply configure interrupt for
wakeup and rely on idle logic within the controller to reduce power
consumption while it is not used.
Signed-off-by: James Chen <james.chen@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Move timestamp from struct vb2_v4l2_buffer to struct vb2_buffer
for common use, and change its type to u64 in order to handling
y2038 problem. This patch also includes all device drivers' changes related to
this restructuring.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The queue_setup callback has a void pointer that is just for V4L2
and is the pointer to the v4l2_format struct that was passed to
VIDIOC_CREATE_BUFS. The idea was that drivers would use the information
from that struct to buffers suitable for the requested format.
After the vb2 split series this pointer is now a void pointer,
which is ugly, and the reality is that all existing drivers will
effectively just look at the sizeimage field of v4l2_format.
To make this more generic the queue_setup callback is changed:
the void pointer is dropped, instead if the *num_planes argument
is 0, then use the current format size, if it is non-zero, then
it contains the number of requested planes and the sizes array
contains the requested sizes. If either is unsupported, then return
-EINVAL, otherwise use the requested size(s).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The goodix touchscreen driver uses a "rotated_screen" flag for
systems on which the touchscreen is mounted rotated by 180
degrees with respect to the display. With the addition of
support for the dt properties "touchscreen-inverted-x" and
"touchscreen-inverted-y", a separate "rotated_screen" flag
is not necessary anymore. This patch replaces it by setting
the inverted_x and inverted_y flags instead.
Signed-off-by: Karsten Merker <merker@debian.org>
Reviewed-by: Irina Tirdea <irina.tirdea@intel.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Implement support for the following device-tree and ACPI 5.1 DSD
properties in the goodix touchscreen driver:
- touchscreen-inverted-x: X axis is inverted (boolean)
- touchscreen-inverted-y: Y axis is inverted (boolean)
- touchscreen-swapped-x-y: X and Y axis are swapped (boolean)
These are necessary on tablets which have a display in portrait
format while the touchscreen is in landscape format, such as e.g.
the MSI Primo 81.
Signed-off-by: Karsten Merker <merker@debian.org>
Tested-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Irina Tirdea <irina.tirdea@intel.com> (with ACPI DSD properties)
Tested-by: Aleksei Mamlin <mamlinav@gmail.com> (with device-tree properties)
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Implement suspend/resume for goodix driver.
The suspend and resume process uses the gpio pins. If the device ACPI/DT
information does not declare gpio pins, suspend/resume will not be
available for these devices.
This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel trees for
various devices).
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Goodix devices can be configured by writing custom data to the device at
init. The configuration data is read with request_firmware from
"goodix_<id>_cfg.bin", where <id> is the product id read from the device
(e.g.: goodix_911_cfg.bin for Goodix GT911, goodix_9271_cfg.bin for
GT9271).
The configuration information has a specific format described in the Goodix
datasheet. It includes X/Y resolution, maximum supported touch points,
interrupt flags, various sensitivity factors and settings for advanced
features (like gesture recognition).
Before writing the firmware, it is necessary to reset the device. If
the device ACPI/DT information does not declare gpio pins (needed for
reset), writing the firmware will not be available for these devices.
This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel
trees for various devices).
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
After power on, it is recommended that the driver resets the device.
The reset procedure timing is described in the datasheet and is used
at device init (before writing device configuration) and
for power management. It is a sequence of setting the interrupt
and reset pins high/low at specific timing intervals. This procedure
also includes setting the slave address to the one specified in the
ACPI/device tree.
This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel
trees for various devices).
For reset the driver needs to control the interrupt and
reset gpio pins (configured through ACPI/device tree). For devices
that do not have the gpio pins properly declared, the functionality
depending on these pins will not be available, but the device can still
be used with basic functionality.
For both device tree and ACPI, the interrupt gpio pin configuration is
read from the "irq-gpios" property and the reset pin configuration is
read from the "reset-gpios" property. For ACPI 5.1, named properties
can be specified using the _DSD section. This functionality will not be
available for devices that use indexed gpio pins declared in the _CRS
section (we need to provide backward compatibility with devices
that do not support using the interrupt gpio pin as output).
For ACPI, the pins can be specified using ACPI 5.1:
Device (STAC)
{
Name (_HID, "GDIX1001")
...
Method (_CRS, 0, Serialized)
{
Name (RBUF, ResourceTemplate ()
{
I2cSerialBus (0x0014, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\I2C0",
0x00, ResourceConsumer, ,
)
GpioInt (Edge, ActiveHigh, Exclusive, PullNone, 0x0000,
"\\I2C0", 0x00, ResourceConsumer, ,
)
{ // Pin list
0
}
GpioIo (Exclusive, PullDown, 0x0000, 0x0000,
IoRestrictionOutputOnly, "\\I2C0", 0x00,
ResourceConsumer, ,
)
{
1
}
})
Return (RBUF)
}
Name (_DSD, Package ()
{
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package (2) {"irq-gpios", Package() {^STAC, 0, 0, 0 }},
Package (2) {"reset-gpios", Package() {^STAC, 1, 0, 0 }},
...
}
}
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Each of the Goodix devices supported by this driver has a fixed size for
the configuration information registers. The size varies depending on the
device and is specified in the datasheet.
Use the proper configuration length as specified in the datasheet for
each device model, so we do not read more than the actual size of the
configuration registers.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This makes Logitech PS2++ protocol implementation consistent with
the naming in other protocols. Also mark the stub as "static inline"
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
PS/2 protocol is slow, and using it with pass-through port (where we
encapsulate PS/2 into PS/2) is slower yet so it takes quite a bit of time
to do full protocol discovery for device attached to a pass-through port.
However, so far we have not see anything but trackpoints or basic PS/2
mice on pass-through ports, so let's limit protocols that we probe there
to Trackpoint, IntelliMouse Explorer, IntelliMouse, and bare PS/2 protocol,
and avoid other extended protocols, such as Synaptics, ALPS, etc.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation of limiting protocols that we try on pass-through ports,
let's rework initialization code and factor common code into
psmouse_try_protocol() that accepts protocol type (instead of detec()
function pointer) and can, for most protocols, perform both detection and
initialization.
Note that this removes option of forcing Lifebook protocol on devices that
are not recognized by lifebook_detect() as having the hardware, but I do
not recall anyone using this option.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We move protocol descriptions and psmouse_find_by_type() and
pmouse_find_by_name() so that we can use them without forward declarations
in the subsequent patches.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When Cypress protocol support is disabled cypress_init() is a stub that
always returns -ENOSYS, so there is not point in testing for
CONFIG_MOUSE_PS2_CYPRESS after we decided that we are dealing with a
Cypress device. Also, we should only be calling cypress_detect() when
set_properties argument is "true", like with other protocols.
There is a slight change in behavior to make follow-up patches more
uniform: when we detect Cypress but its initialization fails, instead of
immediately returning PSMOUSE_PS2 protocol we now continue trying
IntelliMouse [Explorer]. Given that Cypress devices only have issue with
Sentelic probes probing Imtellimouse should be safe.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The fact that we were calling focaltech_init() even when Focaltech support
is disabled was confusing. Rearrange the code so that if support is
disabled we continue to fall through the rest of protocol probing code
until we get to full reset that Focaltech devices need to work properly.
Also, replace focaltech_init() with a stub now that it is only called when
protocol is enabled.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The module was using non-standard comment style with comment blocks often
starting at the very beginning of a line instead of being aligned with the
code. Let's switch to standard formatting.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of a series mostly exclusive "if" statements testing protocol type
of the mouse let's use "switch" statement.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On this board, the touchscreen, an ads7843, is not handled directly by
Linux but by a companion FPGA. This FPGA is memory-mapped and the IP
design is very similar to the mk712.
This commit adds the support for this IP.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are two EETI touchscreen drivers in the kernel (eeti_ts and
egalax_ts) but both are for I2C-connected panels. This is for a different,
serial and not multi-touch touchscreen panel. The protocol documentation is
at http://www.eeti.com.tw/pdf/Software%20Programming%20Guide_v2.0.pdf
Signed-off-by: Böszörményi Zoltán <zboszor@pr.hu>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Previously the "vendor" and "product" IDs for the elan_i2c driver simply
reported 0000. This patch modifies the elan_i2c driver to include the
Elan vendor ID and the touchpad's product id under
input/input*/{vendor,product}.
Specifically, this is to allow us to apply a generic Elan gestures config
that will apply to all Elan touchpads on ChromeOS. These configs match to
input devices in various ways, but one major way is by matching on vendor
ID. Adding this patch allows the default Elan touchpad config to be
applied to Elan touchpads in this kernel by matching on devices that have
vendor ID 04f3.
Note that product ID is also available via custom sysfs entry "product_id"
as well.
Signed-off-by: Charlie Mooney <charliemooney@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stop reporting KEY_SLEEP for a short key-press and report KEY_POWER instead
This change applies to both DA9063 and DA9062 ONKEY drivers.
A previous application used for testing by the developer required a
KEY_SLEEP and KEY_POWER input_report_key event to distinguish between a
short and long key-press of the power key. This is not the general
convention and the typical solution is for KEY_POWER to be used in both
cases: suspend and S/W power off.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Atmel maxtouch DT binding documents that the compatible string for
the device is "atmel,maxtouch" and the I2C core always reports a module
alias of the form i2c:alias where alias is the compatible string model:
$ grep MODALIAS /sys/devices/platform/12e00000.i2c/i2c-8/8-004b/uevent
MODALIAS=i2c:maxtouch
But there isn't maxtouch entry in the I2C device ID table so when the
i2c:maxtouch MODALIAS uevent is reported, kmod is not able to match the
alias with a module to load:
$ modinfo atmel_mxt_ts | grep alias
alias: of:N*T*Catmel,maxtouch
alias: i2c:mXT224
alias: i2c:atmel_mxt_tp
alias: i2c:atmel_mxt_ts
alias: i2c:qt602240_ts
So add the maxtouch entry to the I2C device ID table to allow the module
to be autoloaded when the device is registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On some devices the wake and enable pins of the pixcir touchscreen
controller are connected to gpios and these must be controlled by the
driver for the device to operate properly.
Signed-off-by: Sander Vermin <sander@vermin.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Linus Torvalds