Frames are considered pending when they reside in the driver TX queue or
already queued in the FW.
This notion of "pending" is appropriate for power save considerations in
STA mode, but not necessarily in other modes (for instance P2P-GO).
[Fixed a sparse warning about missing "static" in a function
declaration -- Luca]
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The FW can dynamically manage its internal TX & RX memory pools, moving
blocks from one pool to another when necessary. This can significantly
improve performance. Currently this feature is enabled only for 128x.
Enable dynamic memory for 127x as well. Other parameters in the memory
configuration structure may need to be fine tuned, as the optimal values
for these may change once dynamic memory is enabled.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The driver stops sending TX packets when either there aren't enough
memory blocks, or it runs out of TX descriptors. The driver continues to
send packets to the FW only when more memory blocks are available.
The FW might free TX descriptors without freeing the corresponding
memory blocks, especially when dynamic memory is enabled. In cases where
memory blocks are not freed at all, the driver will keep waiting for
more memory blocks indefinitely.
Fix this by clearing the WL1271_FLAG_FW_TX_BUSY flag when there are
available TX descriptors.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The 128x/AP firmware does not yet support dynamic memory. Temporarily,
the memory configuration for the 127x was used both for 127x/AP as well
as 128x/AP. Since the two chips don't have the same number of memory
blocks, TP was significantly degraded.
This hasn't been fine tuned yet, but using the base 128x numbers
(without dynamic memory) seems to yield much better results (around 30%
more). Additional fine tuning will be required in the future.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When configuring ACX_WAKE_UP_CONDITIONS (before entering psm), we
tell the firmware to wake up once in N DTIMs/beacons.
Allow control of this value via debugfs (for debugging purposes).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reducing the retries of sending PS exit packets to the peer AP.
That fix is to avoid sending unrealizable number of PS exit packets
in case of ap lost.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add support to FM WLAN coexistence (STA only). Some WiFi harmonics
may interfere with FM operation, to avoid this problem special
coexistence techniques are activated around some FM frequencies.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When working in ibss mode, we don't configure rate policy per station
(as we use the same link for multiple stations), so currently the
1mb/s rate is being used.
Instead, configure the firmware to use the whole 11b rates by default.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
ieee80211_reconfig() sets most of the "changed" flags regardless
of the actual change (e.g. BSS_CHANGED_ASSOC will be set even if
the interface is still not associated). in this case the driver
will issue some unneeded commands.
Since the driver relies solely on the BSS_CHANGED_ASSOC flag,
without checking if there was an actual change, it will end up
issuing unjoin() and dummy_join() commands, although it was
never associated and should just remain idle.
Avoid it by checking the actual state change, in addition to the
"changed" flag.
(there seem to be more redundant configuration commands being
issued, but they shouldn't harm)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When debugging, reduce the padding size from each rx packet, to
get the actual packet size (so comparing it against a cap file
will be easier)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Fix mismatch between the REF CLK and TCXO CLK information that is
set in the platform data and the NVS, so we override what comes
from the NVS and replace it with what comes from the platform data.
[Small fix in a comment -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The elp_work is being enqueued on wl1271_ps_elp_sleep, but doesn't get
cancelled on wl1271_ps_elp_wakeup. This might cause immediate entrance
to elp when the wl->mutex is being released, rather than using the delayed
enqueueing optimization.
Cancel elp_work on wakeup request, and add a new WL1271_FLAG_ELP_REQUESTED
flag to further synchronize the elp actions.
[Fixed a couple of typos in some comments -- Luca]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
commit d05c806 ("wl12xx: rearrange some ELP wake_up/sleep calls")
introduced a bug in which wl1271_ps_elp_wakeup() was called instead
of wl1271_ps_elp_sleep() after completing the tx work.
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
End-of-transaction flag should be set when working with
wl127x chip on AP mode.
Thanks Ido Yariv <ido@wizery.com> for the guidance with that.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If an interface type changes from a type that is
only supported on the PAN context (e.g. P2P GO)
to a type that is supported on the BSS context,
and the BSS context is not in use, then we need
to use the BSS context instead of changing the
device type within the context. To achieve this,
refuse the type change, which causes a down/up
cycle that will allocate the BSS context for the
interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The current RXON checking doesn't verify that
the channel is valid (or at least non-zero),
so add that. Also, add a WARN() so we get a
stacktrace, and capture a bitmask of errors
in order to capture all necessary information
in the warning itself (in case the previous
messages are snipped off.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This header file isn't used, and if we ever need
these definitions they shouldn't be added to a
driver but rather to the common 802.11 include
file that has all frame definitions. Thus, just
remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
All agn devices use the same eeprom semaphore and calib version routines.
Delete the indirection and move the semaphore routines to where they are
used and make static.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
All agn devices use the same module parameter structure. Delete the
indirection and access the structure diretly.
Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
New microcode versions use the good CRC threshold
field differently, as a flag, and in that case we
should set it to 1/0 instead of 1/65535 for an
active/passive scan.
The new behaviour is advertised by the uCode with
a feature flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
No functional changes, separate the connect and disconnect sequences in
RXON commit function, easier to read and understand.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The WoWLAN resume code will have to essentially
do a restart, but without going through the work
struct. To support that, refactor the restart by
splitting out the preparation code into a new
function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
There are a few cases like the WoWLAN support
I'm writing that require attempting to access
the NIC when it is known that it might not be
accessible, e.g. after the system woke up and
the platform might have reset the device.
To avoid messages in this case, introduce the
new function iwl_grab_nic_access_silent(), it
will only return an error status.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
If a device error happens while the uCode is
being loaded or initialised, we will attempt
to restart the device (which will likely fail
again, but that's not the issue here). During
this new restart, we turn off the device, but
as the uCode failed to initialise it already
is turned off. As a consequence, grabbing NIC
access will fail and cause excessive messages
and hangs.
To fix this issue, introduce a new status bit
and only attempt to reprogram the device when
it isn't already disabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The tx_headroom required for mwl8k driver is 32 bytes and it
can use the space for 802.11 header received from mac80211.
mwl8k considers the smallest 802.11 frame (CTS2self of 10
bytes) that can be received from mac80211 to compute the
extra_tx_headroom as 22 (32 - 10) bytes.
When the wireless interface is part of bridge, this
extra_tx_headroom requirement results in a memcpy in
mac80211 (in function pskb_expand_head) for all the data
frames needing L2 forwarding/bridging, when NET_SKB_PAD is
defined as 32. This patch reduces the extra_tx_headroom by
8 bytes so that memcpy of data frames in mac80211 is
avoided in this case.
The resize will be required in driver for frames with 802.11
header size of less than 18 bytes.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove all the convoluted hacks in the driver and simplify things
by making use of mac80211's LED triggers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We now use priv->mutex to serialize sync command, remove old
priv->sync_cmd_mutex and add assertion that priv->mutex must be locked.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check status bits with mutex taken, because when we wait for mutex
unlock, status can change. Patch should also make remaining sync
commands be send with priv->mutex taken. That will prevent execute
these commands when we are currently reset firmware, what could
possibly cause troubles.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We mark command as huge by using meta->flags from other (non huge) command,
but flags can be possibly overridden, when non huge command is enqueued,
what can lead to:
WARNING: at lib/dma-debug.c:696 dma_debug_device_change+0x1a3/0x1f0()
DMA-API: device driver has pending DMA allocations while released from device [count=1]
To fix introduce additional CMD_MAPPED to mark command as mapped and
serialize iwl_enqueue_hcmd() with iwl_tx_cmd_complete() using
hcmd_lock. Serialization will also fix possible race conditions,
because q->read_ptr, q->write_ptr are modified/used in parallel.
Do not change callback, I did (and fixed) that mistake in iwlagn.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
struct iwl_queue is not part of firmware interface, so __packed is not
needed. Remove it since is may affect performance.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We never set STATUS_SCANNING in softwre scanning mode, disable_hw_scan
check is unneeded. Correct debug message while at it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't need to use conditional as ch->band is already assigned to
IEEE80211_BAND_5GHZ or IEEE80211_BAND_2GHZ
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add two below iwlwifi commits to iwlegacy:
commit 554d1d027b
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Thu Dec 23 12:38:21 2010 +0100
iwlagn: enable only rfkill interrupt when device is down
commit 3dd823e6b8
Author: Don Fry <donald.h.fry@intel.com>
Date: Sun Feb 6 09:29:45 2011 -0800
iwlagn: Re-enable RF_KILL interrupt when down
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since
commit f844a709a7
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Fri Jan 28 16:47:44 2011 +0100
iwlwifi: do not set tx power when channel is changing
we set device tx power during initialization to priv->tx_power_next,
which itself is initialized to minimum power. That changed
default behaviour of driver. Previously we initialized device to
transmit at maximum available power by default. Patch change again
to previous behaviour and cleanup tx power initialization.
Fortunately this is not critical fix, as mac80211 layer setup
tx power lately to 14dB, hence device does not operate at minimal
transmit power all the time.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/p54/eeprom.o
drivers/net/wireless/p54/eeprom.c: In function ‘p54_parse_rssical’:
drivers/net/wireless/p54/eeprom.c:494:8: warning: ‘freq’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/mwifiex/join.o
drivers/net/wireless/mwifiex/join.c: In function ‘mwifiex_cmd_802_11_associate’:
drivers/net/wireless/mwifiex/join.c:119:8: warning: ‘tsf_val’ may be used uninitialized in this function
drivers/net/wireless/mwifiex/join.c:103:12: note: ‘tsf_val’ was declared here
Looks like a copy-n-paste error, identical lines are a few lines below
the ones removed, with an actual memcpy to tsf_val in between...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/b43/phy_n.o
drivers/net/wireless/b43/phy_n.c: In function ‘b43_nphy_set_channel’:
drivers/net/wireless/b43/phy_n.c:3848:47: warning: ‘tabent_r2’ may be used uninitialized in this function
drivers/net/wireless/b43/phy_n.c:3849:47: warning: ‘tabent_r3’ may be used uninitialized in this function
drivers/net/wireless/b43/phy_n.c: In function ‘b43_nphy_poll_rssi.clone.14’:
drivers/net/wireless/b43/phy_n.c:2270:6: warning: ‘save_regs_phy$7’ may be used uninitialized in this function
drivers/net/wireless/b43/phy_n.c:2270:6: warning: ‘save_regs_phy$8’ may be used uninitialized in this function
FWIW, the usage of these variables is goverened by checks that match
their initializations. So, I think these are actually false warnings.
Still, I would rather avoid the warning SPAM...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/ath/ath5k/reset.o
drivers/net/wireless/ath/ath5k/reset.c: In function ‘ath5k_hw_init_core_clock’:
drivers/net/wireless/ath/ath5k/reset.c💯51: warning: ‘txf2txs’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Need to use broadcast sta_id for management frames, otherwise we broke
BA session in the firmware and get messages like that:
"Received BA when not expected"
or (on older kernels):
"BA scd_flow 0 does not match txq_id 10"
This fix regression introduced in 2.6.35 during station management
code rewrite by:
commit 2a87c26bbe
Author: Johannes Berg <johannes.berg@intel.com>
Date: Fri Apr 30 11:30:45 2010 -0700
iwlwifi: use iwl_find_station less
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Need to use broadcast sta_id for management frames, otherwise we broke
BA session in the firmware and get messages like that:
"Received BA when not expected"
or (on older kernels):
"BA scd_flow 0 does not match txq_id 10"
This fix regression introduced in 2.6.35 during station management
code rewrite by:
commit 2a87c26bbe
Author: Johannes Berg <johannes.berg@intel.com>
Date: Fri Apr 30 11:30:45 2010 -0700
iwlwifi: use iwl_find_station less
Patch partially resolve:
https://bugzilla.kernel.org/show_bug.cgi?id=16691
However, there are still 11n performance problems on 4965 and 5xxx
devices that need to be investigated.
Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since timestamp in beacon buffer keeps changing all the time,
the memcmp check in mwifiex_save_curr_bcn() is redundant.
Remove that memcmp check and also avoid freeing and allocation
of buffer if required beacon buffer size is same as previous one.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) Initialise HT capabilities in cfg80211 properly.
2) Cfg80211 stack may modify "sband->ht_cap" to disable
40Mhz operation in 2.4GHz band (after recent patch
"cfg80211: module_param to disable HT40 in 2.4GHz band")
Therefore read "sband->ht_cap" instead of an adapter variable
"hw_dot_11n_dev_cap" to get HT capabilities.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are some SD8787 cards which don't support 5GHz band.
Therefore initialise 5GHz band parameters only if hardware
supports the band.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AFAICT, this driver is claiming that 24 bits of rate info fit into a
16-bit field in the Tx descriptor. Anyway, the use of bitfields is
frowned-upon for a variety of well-documented reasons...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This callback is used to set the minimum rate for management
frames.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds WMI_BITRATE_MASK_CMDID which can be
used by the set_bitrate_mask() handler.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bump the firmware version to 1.2
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert all libertas/ files to use kernel-doc notation instead
of whatever it was (doxygen?).
Add or fix function parameters in several places.
Use expected style for multi-line comments in lots of places.
Remove erroneous /** in multiple places.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In AP mode we register for the MAX_TX_RETRY and INACTIVE_STA events.
Both are reported to the upper layers as a TX failure in the offending
stations.
In STA mode we register only for the MAX_TX_RETRY event. A TX failure is
interpreted as a loss of connection.
Support for IEEE80211_HW_REPORTS_TX_ACK_STATUS has been removed to avoid
the inherent race condition of a mac80211 TX failure counter in addition
to the FW counter.
This patch depends on "mac80211: allow low level driver to report packet
loss"
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use ps wrappers before accessing hw registers in btcoex.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Generic timer interrupt was not triggered unless autosleep was
disabled. Since autosleep is enabled in the newer chipsets,
enable generic timer for using with bt coex logic.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move bt_stomp to ath9k_hw and add its support for latest chipsets.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 5ed540aecc change the led behavior
for iwlwifi driver; the side effect cause led blink all the time.
Modify the led blink table to fix this problem
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a partial revert of 6eab04a876 ("treewide: remove extra
semicolons"). Wireless tree removes the code in question in rtlwifi
driver, so drop the hunk to avoid conflict.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix most sparse warnings in rtlwifi, rtl8192ce and rtl8192cu drivers.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change rtl8192ce routines phy and trx for addition of RTL8192SE and RTL8192DE.
In addition, make necessary modifications to rtl8192cu. This patch also
removes the temporary patches needed to enable intermediate steps to build
without error.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change rtl8192ce routines phy and rc for addition of RTL8192SE and
RTL8192DE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change rtl8192ce sw and LED routines for addition of RTL8192SE and
RTL8192DE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change rtl8192ce hw routine for addition of RTL8192SE and RTL8192DE.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change common PHY routines for addition of RTL8192SE and RTL8192DE code.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change common firmware routines for addition of RTL8192SE and
RTL8192DE code.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert common dynamic management routines for addition of RTL8192SE
and RTL8192DE code.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert usb routines for addition of RTL8192SE and RTL8192DE code
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert regulatory domain routines for addition of RTL8192SE and
RTL8192DE code.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert rc routines for addition of RTL8192SE and RTL8192DE code
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert ps routines for addition of RTL8192SE and RTL8192DE code
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert pci routines for addition of RTL8192SE and RTL8192DE code
These changes allow the upper-level driver to specify the BAR to be
used as it is different for rtl8192se than for the others.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert core routines for addition of RTL8192SE and RTL8192DE code.
Additional files are changed to allow compilation.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change cam routines for addition of RTL8192SE and RTL8192DE code
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change base routines for addition of RTL8192SE and RTL8192DE code.
Additional files are modified to allow compilation.
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change wifi.h for addition of RTL8192SE and RTL8192DE code
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change efuse routines for addition of RTL8192SE and RTL8192DE code
Signed-off-by: Chaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the ieee80211_sta_block allows the PS code
to handle awake->doze->awake transitions of our
clients in a race-free manner.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"For best CPU usage and power consumption, having as few
frames as possible percolate through the stack is
desirable. Hence, the hardware should filter as much
as possible."
Note: Not all firmwares include the multicast filter
feature and the stack does not filter them either.
The ARP filter on the other hand was dropped from the
patch since it does not work correctly:
Quote from: Max Filippov <jcmvbkbc@gmail.com>
<http://www.spinics.net/lists/linux-wireless/msg67466.html>
"In the ARP case, when there's no other traffic on p54spi,
all ARP requests are dropped. But if there's some egress
traffic from p54spi, filter seems to work correctly:
only ARP requests that match filter pass through.
In the multicast case filter seems to work correctly, but
it treats broadcast as subject to that filtering too. By
default only 01:00:5e:00:00:01 gets into priv->mc_maclist,
so we miss all broadcasts.
These two filters seem to interfere:
- if we set ARP filter and multicast filter without bc
=> we miss all ARPs if there's no egress traffic;
- if we set ARP filter and multicast filter with bc or
don't set mc filter at all => we get all ARPs.
This effect does not depend on filter setup order."
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Tested-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The xpaBiasLvlFreq parameter array is made up of 16 bit words which
aren't byte-swapped like the other 16-bit eeprom parameters are.
It's only used by the AR9160.
Signed-off-by: Adrian Chadd <adrian@freebsd.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Requesting beacon sync up to configure beacon timers properly
in hw, has be done after doing beacon config with default values.
Setting the flags in beacon config is causing the device to not
enter into network sleep on idle state.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR9003 chips, doing three IQ calibrations will possibly cause chip
in stuck state. In noisy environment, chip could receive
a packet during the middle of three calibrations and it causes
the conflict of HW access and the eventual failure. It also
causes IQ calibration outliers which results in poor Tx EVM.
The IQ Cal procedure is after resetting the chip, run IQ cal 3 times
per each cal cycle and find the two closest readings and average of two.
The advantage of running Tx IQ cal more than once is that we can compare
calibration results for the same gain setting over multiple iterations.
Most of the cases the IQ failures were observed after first pass.
For the AR9485 and later chips, Tx IQ Calibration is performed along
with AGC cal. But for pre-AR9485 chips, Tx IQ cal HW has to be separated
from the rest of calibration HW to avoid chip hang. After all
calibrations are done in HW, we can start SW post-processing.
By doing this way, we minimize the SW difference among all chips.
The order of calibration (run IQ cal before other calibration) is also
needed to avoid chip hang for chips before AR9485. This issue was
originally observed with AR9382.
During the issue kernel log was filled with following message
ath: timeout (100000 us) on reg 0xa640: 0x00000001 & 0x00000001 != 0x00000000
ath: timeout (100000 us) on reg 0xa2c4: 0x00158dd9 & 0x00000001 != 0x00000000
ath: Unable to reset channel (2412 MHz), reset status -5
ath: Unable to set channel
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Resolved logic conflicts causing a build failure due to
drivers/net/r8169.c changes using a patch from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Using C line continuation inside format strings is error prone.
Clean up the unintended whitespace introduced by misuse of \.
Neaten correctly used line continations as well for consistency.
drivers/scsi/arcmsr/arcmsr_hba.c has these errors as well,
but arcmsr needs a lot more work and the driver should likely be
moved to staging instead.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This helped the developers to fix an issue of chip not entering network
sleep during idle state, previously this was only available as a debug
message
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
newer chipsets support auto sleep feature, so remove the
unlikely check which does not seems to help anything
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should protect hw_pll handler with power save wrappers and
also modularize hw_pll handler properly for better readability.
Also add a debug message to track chip resets on pll hang condition.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no reason why pll work handler should be part of xmit
file. move it to main.c so that reading hw check routines are
all in the same place.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need not wake up the chip even before mutex lock is acquired and also
that it is required only if we are going to drain the txq. So place the
wrappers accordingly and this change is also useful when there are no
pending frames in the txq as we do not wake up the chip unnecessarily.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we should program the AR9485 baseband PLL phase shift to 6 and
a redundant setting overwrites the correct value. Remove the
incorrect and unwnated register setting.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The LED gpio is incorrectly programmed for AR9300 and so the led
is not working propelry. AR93xx uses gpio 10 for LED and not the
default.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hw next tigger time is configured as current_tsf + (timer_period * 10) which
is wrong, it should be current_tsf + timer_period. The wrong hw timer configuration
would cause btcoex related issues.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Tell the firmware to enable the life time expiry of tx packets
in the hardware. The hardware will now refer to the timestamp
in every tx packet and decide whether the packet needs to be
dropped or transmitted.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since queues are not stopped anymore, management frames would be
dropped if the corresponding tx queue is full.
This can cause issues say when we want to setup an ampdu stream and
action frames i.e addba requests keep getting dropped frequently.
Fix this by reserving some buffers to allow management frames to
go through in queue full conditions.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Timestamp tx packets using a HW micro-second timer.
This timestamp will be compared to the current timestamp
in the hardware and if the difference is greater than 500ms,
the packet will be dropped.
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is in preparation to support life time expiry of packets in the
hardware to avoid head-of-line blocking where a slow client can
hog a tx queue and affect the traffic to a faster client from the same
queue. Time stamp the packets in driver to allow dropping them in the
hardware if they are queued for more than 500ms.
If queues are stopped, packets will be queued up outside the driver.
Since we will be able to timestamp the packets only after they hit the
driver, the timestamp will be less accurate since we cannot consider
the time the packets spent in queues outside the driver. With this commit,
to achieve accurate timestamping, the tx queues will not be stopped in
normal conditions. The only scenarios where the queues will be stopped are
when firmware commands are executing or if the interface is brought down.
Now, we need to be prepared for a situation where packets hit the driver
even after the tx queues are full. Drop all such packets in the driver itself.
Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My commit 3598e1774c
"iwlwifi: fix enqueue hcmd race conditions" move hcmd callback after
command queue reclaim, to avoid call it with hcmd_lock. But since
queue read index was updated, cmd data can be overwritten. Fix problem
by calling callback before taking hcmd_lock and queue reclaim.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the maximum ampdu size of a station correctly
in the target by using the ampdu_factor.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Register the driver's maximum ampdu subframe limit to mac80211.
* Cleanup the target capabilities structure and fix an endian issue.
* Fix BTCOEX by sending a command to the target when the BT priority
changes.
* Bump the required firmware version to 1.1
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9340 is a AR9003 family built-in 2x2 wmac of ar934x SOCs. It is single band
in ar9341 SOC and dual band in ar9344/ar9342 SOCs.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use hw supported chains instead of hard coded values.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a bool in ath9k_platform_data to pass AHB clock speed information.
Driver needs this to configure PLL on some SOCs.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This variable is only ever checked right after
the function that sets it, but the same function
will also return the status, so we can pass it
through instead of checking hw_ready later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
On new hardware, ucode images always come in
pairs: code and data. Therefore, combine the
variables into an appropriate struct and use
that when both code and data are needed.
Also, combine allocation and copying so that
we have less code in total.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The current firmware loading mechanism in
iwlwifi is very hard to follow, and thus
hard to maintain. To make it easier, make
the firmware loading synchronous.
For now, as a side effect, this removes a
number of retry possibilities we had. It
isn't typical for this to fail, but if it
does happen we restart from scratch which
this also makes easier to do should it be
necessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
When the firmware encounters an error while the
driver is waiting for a notification, it will
never get that notification. Therefore, instead
of timing out, bail out on errors when waiting
for notifications.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
We're unlikely to care about the actual time spent
waiting, so make the function return an error code
which is less error prone in coding new uses.
Also, while at it, mark __must_check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
A notification wait function is called with the
command, but currently has no way of passing
data back to the caller -- fix that by adding a
void pointer to the function that can be used
between the caller and the function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Starting the device consists of many things,
refactor out enabling the hardware and also
return -ERFKILL when the rfkill signal is
found to be asserted (which makes more sense
anyway, but is also required now to make the
__iwl_up function return right away.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The iwl_down path really consists of multiple things,
refactor out the hardware resetting (including, of
course, related software state like irqs).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
There's no point in running through iwl_down()
when we never registered with mac80211, as it
just cleans up internal structures that were
never initialised in this case. Therefore we
can also remove the special handling for this
case from __iwl_down().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The current code to read the error table header
just hardcodes all the offsets, which is a bit
hard to understand. We can read in the entire
header (as much as we need) into a structure,
and then take the data from there, which makes
it easier to understand. To read a bigger blob
we also don't need to grab NIC access for each
word read, making the code more efficient.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since
commit a120e912eb
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Fri Feb 19 15:47:33 2010 -0800
iwlwifi: sanity check before counting number of tfds can be free
we use skb->data after calling ieee80211_tx_status_irqsafe(), which
could free skb instantly.
On current kernels I do not observe practical problems related with
bug, but on 2.6.35.y it cause random system hangs when stressing
wireless link, making bisection of other problems impossible.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since
commit a120e912eb
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Fri Feb 19 15:47:33 2010 -0800
iwlwifi: sanity check before counting number of tfds can be free
we use skb->data after calling ieee80211_tx_status_irqsafe(), which
could free skb instantly.
On current kernels I do not observe practical problems related with
bug, but on 2.6.35.y it cause random system hangs when stressing
wireless link.
Cc: stable@kernel.org # 2.6.32+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement the get_antenna and set_antenna callback functions, which will
allow clients to control the antenna for all non-11n hardware (Antenna handling
in rt2800 is still a bit magical, so we can't use the set_antenna for those drivers
yet).
To best support the set_antenna callback some modifications are needed in the
diversity handling. We should never look at the default antenna settings to determine
if software diversity is enabled. Instead we should set the diversity flag when
possible, which will allow the link_tuner to automatically pick up the tuning.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the get_ringparam callback function we can export ring parameters
to ethtool through the mac80211 interface.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All register reads/writes in rt2800usb were previously done with
rt2800_register_read/rt2800_register_write. These however indirectly
call rt2x00usb_register_read/rt2x00usb_register_write which adds an
additional overhead of at least one call and several move instructions
to each register access.
Replacing the calls to rt2800_register_read/rt2800_register_write with
direct calls to rt2x00usb_register_read/rt2x00usb_register_write gets
rid of quite a number of instructions in the drivers hotpaths (IRQ
handling and txdone handling).
For consistency replace all references to rt2800_register_read/write
with the rt2x00usb_register_read/write variants.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All register reads/writes in rt2800pci were previously done with
rt2800_register_read/rt2800_register_write. These however indirectly
call rt2x00pci_register_read/rt2x00pci_register_write which adds an
additional overhead of at least one call and several move instructions
to each register access.
Replacing the calls to rt2800_register_read/rt2800_register_write with
direct calls to rt2x00pci_register_read/rt2x00pci_register_write gets
rid of quite a number of instructions in the drivers hotpaths (IRQ
handling and txdone handling).
For consistency replace all references to rt2800_register_read/write
with the rt2x00pci_register_read/write variants.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The two functions that are in rt2x00ht.c can be much better placed
closer to the places where the call-sites of these functions are (one
in rt2x00config.c and one in rt2x00queue.c) allowing us to make these
functions static.
Also, conditional compilations doesn't seem to be necessary anymore as
802.11n support is quite common nowadays.
This makes the code a bit easier readable and searchable.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Code seems to be feature-complete, so no reason to not enable
these devices by default.
Also, remove the sentence about the support for these devices being
non-functional.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt33xx devices support for both PCI and USB devices has been in
the tree for a couple of months now, and seems to be functional and
not in a worse shape than the support for rt28xx and rt30xx devices.
No longer mark it as experimental and enable the support for these
devices by default.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add USB IDs that are listed in the latest Ralink Windows and/or Linux drivers.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both USB and PCI drivers allow a system administrator to dynamically add
USB/PCI IDs to the device table that a driver supports via the
/sys/bus/{usb,pci,pci_express}/drivers/<driver-name>/new_id files.
However, for the rt2x00 drivers using this method currently crashes the
system with a NULL pointer failure.
This is due to the set-up of rt2x00 where the probe functions require a
rt2x00_ops structure in the driver_info field of the probed device. As
this field is empty for the dynamically added devices this fails for
these devices.
Fix this by introducing driver-specific probe wrappers that do nothing
but calling the bus-specific probe functions with the rt2x00_ops structure
as an argument, rather than depending on the driver_info field.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the USB ID entry from the unknown devices to the list of RT35xx based
devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows the compiler to perform the necessary bitfield calculations
during compile time instead of run time and thus reduces the number of
instructions to run during each tasklet invocation. This should improve
performance in the RX hotpath.
This comes at the cost of a slight increase in the module size (for
example rt2800pci):
Before:
text data bss dec hex filename
14133 832 4 14969 3a79 drivers/net/wireless/rt2x00/rt2800pci.ko
After:
text data bss dec hex filename
14149 832 4 14985 3a89 drivers/net/wireless/rt2x00/rt2800pci.ko
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When powersaving is enabled, assocaition times are very high
(for WPA2 networks, the time can easily be around the 3 seconds).
This is caused, because the flushing of the queues takes
too much time. Without the flushing callback mac80211 assumes
a timeout of 100ms while scanning. Limit all flush waiting
loops to the same maximum.
We can apply this maximum by passing the drop status to the
driver, which makes sure the driver performs extra actions
during the waiting for the queue to become empty.
After these changes, association times fall within the
healthy range of ~0.6 seconds with powersaving enabled.
The difference between association time between powersaving
enabled and disabled is now only ~0.1 second (which can also
be due to the measuring method).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX status is reported by the hardware when a packet has been
sent (or after TX failed after possible retries), which is some
time after the DMA completion. Since the rt2800usb hardware can
not signal interrupts we have to use a timer, otherwise the
TX status would only be read by the next packet's TX DMA
completion, or by the watchdog thread.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The watchdog just triggers rt2800usb_work_txdone() when it
detects a TX status timeout, thus rt2800usb_work_txdone() needs to
handle this case.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a timestamp to each queue entry which is updated whenever
the status of the entry changes, and remove the per-queue
timestamps. The previous check was incorrect and caused both
false positives and false negatives.
With the corrected check it comes apparent that the TX status
usually times out on rt2800usb unless there is sufficient traffic
(i.e. the next TX will complete the previous TX status).
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trying to fix the "TX status report missed" warnings
by reading the TX_STA_FIFO entries as quickly as possible.
The TX_STA_FIFO is too small in hardware, thus reading
it only from the workqueue is too slow and entries get lost.
Start an asynchronous read of the TX_STA_FIFO directly from
the TX URB completion callback (atomic context, thus it cannot
use the blocking rt2800_register_read()). If the async
read returns a valid FIFO entry, it is pushed into a larger
FIFO inside struct rt2x00_dev, until rt2800_txdone() picks
it up.
A .tx_dma_done callback is added to struct rt2x00lib_ops
to trigger the async read from the URB completion callback.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use TXOP_HTTXOP for beacons to stay in sync with the legacy drivers.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bring the TX_SW_CFG2 initialisation for rt305x devices in sync with the
ralink legacy drivers.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This seems to fix problems with some powersaving clients since a
positive value in TBTT_SYNC_CFG_TBTT_ADJUST introduces beacon skew,
which is not wanted in AP mode.
Also update the rest of the TBTT_SYNC config according to the
legacy drivers in AP mode.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow passing a void pointer to rt2x00_queue_entry_for_each which in
turn in provided to the callback function.
Furthermore, allow the callback function to stop processing by returning
true. And also notify the caller of rt2x00_queue_entry_for_each if the
loop was canceled by the callback.
No functional changes, just preparation for an upcoming patch.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number of flags defined for the rt2x00dev->flags field,
has been growing over the years. Currently we are approaching
the maximum number of bits which are available in the field.
A secondary problem, is that one part of the field are initialized only
during boot, because the driver requirements are initialized or device
requirements are loaded from the EEPROM. In both cases, the flags are
fixed and will not change during device operation. The other flags are
the device state, and will change frequently. So far this resulted in the fact
that for some flags, the atomic bit accessors are used, while for the others
the non-atomic variants are used.
By splitting the flags up into a "flags" and "cap_flags" we can put all flags
which are fixed inside "cap_flags". This field can then be read non-atomically.
In the "flags" field we keep the device state, which is going to be read atomically.
This adds more room for more flags in the future, and sanitizes the field access methods.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since commit 0b7fde54f9 "rt2x00: Protect
queue control with mutex" rt2x00 used rt2x00queue_pause_queue for
stopping a tx queue in mac80211. But in case of a failure in the tx
path rt2x00 still called ieee80211_stop_queue which stopped the queue
but prevented rt2x00queue_unpause_queue to wake the queue up again
resulting in a stuck tx queue.
Fix this by also using rt2x00queue_pause_queue in case of tx failures.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds WLAN LED support to the mac80211 rt2x00 driver for
Ralink SoC (rt305x) devices. The current WLAN LED drivers in
rt2800lib.c set the LED brightness via an MCU request, but do nothing
for SoC. This patch checks for SoC and sets the register to enable the
WLAN LED (instead of an MCU request). This enables the WLAN LED for
RT305x devices.
Signed-off-by: Layne Edwards <ledwards@astrumtech.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Frame filtering relies on having a valid destination index (keycache slot),
to keep track of the destination. Assigning a keycache slot (configured
to unencrypted, with no key data attached) improves powersave handling in
AP mode with no encryption.
The dummy keycache entry for a station is cleared, when a real key gets
added.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a long standing issue of pending packets in the queue being
sent (and retransmitted many times) to sleeping stations.
This was made worse by aggregation through driver-internal retransmitting
of A-MDPU subframes.
Previously the hardware tx filter was cleared unconditionally for every
single packet - with this patch it uses the IEEE80211_TX_CTL_CLEAR_PS_FILT
for unaggregated frames.
A sta_notify driver op is added to stop aggregation for stations when they
enter powersave mode. Subframes stay buffered inside the driver, to ensure
that the BlockAck window keeps a sane state.
Since the driver uses software aggregation, the clearing of the tx filter
needs to be handled by the driver instead of mac80211 for aggregated frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While leaving the oper channel, beacon generation is stopped
by mac80211 and beacon slots are marked as inactive.
During the scan, ath9k configures beacon timers
based on IEEE80211_CONF_OFFCHANNEL which inturn generates
beacon alert even though bslot is inactive.
ath9k fails to disable beacon alert while moving to offchannel
if none of the beacon slot is active. This is causing beacon
transmission on foreign channel. This patch enables swba
based on active bslots.
This issue was reported with two vifs (AP+STA) and triggered
scan in STA vif in unassociated state.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_htc_tx_get_slot can return zero as valid index.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Sujith Manoharan <Sujith.Manoharan@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) removal of unnecessary mwifiex_device structure
2) avoid passing adapter pointer to mwifiex_init_sw()
3) remove local variable drv_mode_info in mwifiex_add_card()
4) type change in mwifiex_bss_attr to match mwifiex_private
5) removal of more wordy comments
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use corresponding macros defined in include/linux/ieee80211.h
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove some local variables (mainly function return values)
that are used only once. Also, one dummy function and some
wordy comments are removed.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit be663ab670 (iwlwifi: split the drivers for
agn and legacy devices 3945/4965) added code to read the 4965's revision ID from
the PCI configuration register while it's already stored by PCI subsystem in the
'revision' field of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the ath9k_htc debugfs under ieee80211 to be inline
with ath9k driver and it also helps to simplify debug code.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Acked-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 0x6C regulatory domain is just like the 0x6A regulatory
domain but differs in that 0x6C will allow adhoc and active
scan on its channels only if we are associated to an AP
with a country IE that allows those channels. The
ath_reg_apply_beaconing_flags() does just this -- we respect
the manufacturer's intent on only enabling beaconing modes
of operation if and only if blessed by the country IE.
Cc: David Quan <david.quan@atheros.com>
Cc: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch 'ath9k_hw: fix stopping rx DMA during resets' added code to detect
a condition where rx DMA was stopped, but the MAC failed to enter the idle
state. This condition requires a hardware reset, however the return value
of ath_stoprecv was 'true' in that case, which allowed it to skip the reset
when issuing a fast channel change.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Paul Stewart <pstew@google.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix sparse warning:
CHECK drivers/net/wireless/wl12xx/main.c
drivers/net/wireless/wl12xx/main.c:1246:17: warning: symbol 'wl12xx_alloc_dummy_packet' was not declared. Should it be static?
Signed-off-by: Luciano Coelho <coelho@ti.com>
Instead of hardcoding the hci_io_ds configuration that we write to the
SDIO_IO_DS top registed, read it from the default configuration so
that it's easier to change for different platforms.
Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Some platforms are incapable of triggering on level interrupts. Add a
platform quirks member in the platform data structure, as well as an
edge interrupt quirk which can be set on such platforms.
When the interrupt is requested with IRQF_TRIGGER_RISING, IRQF_ONESHOT
cannot be used, as we might miss interrupts that occur after the FW
status is cleared and before the threaded interrupt handler exits.
Moreover, when IRQF_ONESHOT is not set, iterating more than once in the
threaded interrupt handler introduces a few race conditions between this
handler and the hardirq handler. Currently this is worked around by
limiting the loop to one iteration only. This workaround has an impact
on performance. To remove to this restriction, the race conditions will
need to be addressed.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The total number of TX memory blocks may change when the dynamic memory
option is enabled. The current implementation only tracks the available
memory blocks, which over-complicates TX blocks accounting.
By tracking the number of allocated blocks, calculation of the number of
available blocks becomes simpler and cleaner. It simply equals the total
number of TX memory blocks minus the allocated ones.
Also, remove some unnecessary castings and use union member accesses
instead.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The current implementation allocates a skb each time one is requested by
the firmware. Since dummy packets are handled differently than regular
packets, the skb needs to be marked. Currently, this is done by
setting the pkt_type member to 5. This might not be safe, as we cannot
be sure that there won't be any other packets with this pkt_type value.
Since the packet does not change from one request to another, we can
simply allocate a dummy packet template and always send it. All changes
to the skb done during packet preparation must be reverted, so the same
skb can be reused.
The dummy packets are not transmitted, therefore there's no need to set
the BSSID or our own MAC address.
In addition, the header portion of the packet was zeroed by mistake, so
fix that as well.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Simplify and clean up the block size alignment code:
1. Set the block size according to the padding field type, as it cannot
exceed the maximum value this field can hold.
2. Move the alignment code into a function instead of duplicating it in
multiple places.
3. In the current implementation, the block_size member can be
misleading because a zero value actually means that there's no need to
align. Declare a block size alignment quirk instead.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Clean up the boot sequence code & fix the following issues:
1. Always read the registers' values and set the relevant bits instead of
zeroing all other bits
2. Handle cases where wl1271_top_reg_read returns an error
3. Verify that the HW can detect the selected clock source
4. Remove 128x PG10 initialization code
5. Configure the MCS PLL to work in HP mode
Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Issuing multiple JOIN commands to the wl12xx's firmware, while
we're associated, might have undesired implications, so the driver
prints a message when that happens, and warn developers who check
out the source.
Update the commentary in order to consider the one valid scenario
where this can happen: roaming.
Cautiously keep the message for now, until we either gain confidence
there are no unintentional JOIN-while-associated events, or until
we move to the new multi-role fw who solves this multiple-join issue
for good.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl12xx device normally drops all frames coming from BSSID
it is not joined with.
This behavior is configured today by the wl12xx driver in response
to a handful of ieee80211_bss_change and ieee80211_conf_changed
notification flags, such as BSS_CHANGED_ASSOC, BSS_CHANGED_BSSID,
IEEE80211_CONF_CHANGE_IDLE, etc..
This breaks when we roam to a new BSSID, where authentication frames
are sent before any BSS_CHANGED/CONF_CHANGED flags are received.
When this happens the hardware silently drops the authentication
responses, and the roaming fails.
Ideally this aggressive filtering behavior of the device should be disabled
upon a notification from mac80211. Such notification will take place
after multi-channel support will be added: mac80211 will likely send a
remain-on-channel notification to drivers when entering sensitive
states (like authentication), otherwise the firmware might jump to
different channels (to serve a different role).
Until those notifications materialize, disable the hw BSSID filter
when authentication requests are sent, so roaming would work.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Because of the hardware recovery mechanism, its possible the
__wl1271_op_remove_interface is called twice. Currently, this leads to a
kernel crash even before a kernel WARNing can be issued.
Fix this.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
ELP (Extremely/Enhanced Low Power, or something like that ;)) refers to
the powerstate of the 12xx chip, in which very low power is consumed,
and no commands (from the host) can be issued until the chip is woken up.
Wakeup/sleep commands must be protected by a wl->mutex, so it's generally
a good idea to call wakeup/sleep along with the mutex lock/unlock (where
needed). However, in some places the wl12xx driver calls wakeup/sleep in
some "inner" functions. This result in some "nested" wakeup/sleep calls
which might end up letting the chip go to sleep prematurely (e.g. during
event handling).
Fix it by rearranging the elp calls to come along with mutex_lock/unlock.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Initialize the channel and band from mac80211 conf even when the FW is
not yet loaded. This mitigates a bug in AP-mode where the channel was
never changed from its initial setting after FW boot and was therefore
never configured to FW.
Reported-by: Alexander Boukaty <alexanderb@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We were using an array of booleans to mark the channels we had already
scanned. This was causing a sparse error, because bool is not a type
with defined size. To fix this, use bitmasks instead, which is much
cleaner anyway.
Thanks Johannes Berg for the idea.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Fix the following sparse warnings:
drivers/net/wireless/wl12xx/main.c:1129:5: warning: symbol '__wl1271_plt_stop' was not declared. Should it be static?
drivers/net/wireless/wl12xx/main.c:2988:5: warning: symbol 'wl1271_op_ampdu_action' was not declared. Should it be static?
Both functions should be static.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The Soft Gemini BT load ratio value has changed its meaning with FW
version 6.1.0.0.310. It now means the passive scan compensation
percentage during A2DP EDR. Instead of 50, we need to use 200.
Fix the SG configuration accordingly.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The firmware requires dummy packets to be sent using TID 7
(WL1271_TID_MGMT). Instead of hardcoding it in the tx_fill_hdr()
function, set it when creating the packet itself.
This requires Eliad's fix to set the actual TID in the TX descriptor.
Cc: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When passing a tx frame, the driver incorrectly set desc->tid
with the ac instead of the actual tid.
It has some serious implications when using 802.11n + QoS,
as the fw starts a BlockAck with the wrong tid (which finally
cause beacon loss and disconnection / some fw crash)
Fix it by using the actual tid stored in skb->priority.
Reported-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The interface list maintained in main.c is not mutex protected. This could
cause issues, as the list is accessed from notifier chains.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
On wl128x based devices, when TX packets are aggregated, each packet
size must be aligned to the SDIO block size, and sent using block mode
transfers.
The block size is set to 256 bytes, which is less than the maximum
possible byte transfer. Thus, if two small packets (< 256 bytes) are
aggregated, the aggregation buffer size would be 512, and will be sent
using byte mode transfers. This can have undesired side effects.
Fix this by setting the MMC_QUIRK_BLKSZ_FOR_BYTE_MODE mmc card quirk.
For 127x chips this has no effect, as the block size is set to 512
bytes.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Allow early termination of 50 consecutive beacons.
This value is the recommended one by the 12xx's system/RF team,
and tests show that power consumption is improved as expected.
Reported-by: Ruthy Zaphir <ruthyz@ti.com>
Tested-by: Danil Shalumov <danils@ti.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wl12xx chip supports one Rx STBC spatial stream. Announce this in
the HT capabilities info field.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The rx-status passed to mac80211 along with each received frame contains the
band on which the frame was received. Under certain circumstances, this band
information may be incorrect, causing in worst case a WARNING from mac80211,
and causes the received frame to be dropped.
This scenario mainly occurs when performing connected-mode scans, when the
received scan results are from the other band than the one currently
associated to.
[Since desc_band doesn't exist anymore, use status->band in the later
call to ieee80211_channel_to_frequency() to fix compilation -- Luca]
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
All the new firmware versions (>=6.1.3.50.58 for STA and >=6.2.0.0.47
for AP) use 1 spare TX block. We still want to support older
firmwares that require 2 spare blocks, so added a quirk to handle the
difference.
Also implemented a generic way of setting quirks that depend on the
firmware revision.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add support to wl128x chip via chip id
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Choose a different FW for AP-mode wl127x and wl128x chips, base on chip
ID at boot time.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Support sending dummy packet to wl128x FW as results of
dummy packet event. That is part of dynamic TX mem blocks mechanism.
Only send dummy packet when not in AP mode.
[Even though the DUMMY_PACKET_EVENT_ID and the
STA_REMOVE_COMPLETE_EVENT_ID events are defined to the same value, we
need to treat them separately in the code. Keep the check and enable
STA_REMOVE_COMPLETE_EVENT_ID for AP mode and DUMMY_PACKET_EVENT_ID for
STA. Moved one warning to a cleaner place. Use WL1271_TID_MGMT for
dummy packets -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reduced bus transactions in the Tx & Rx path.
[Removed unnecessary check wl->chip.id != CHIP_ID_1283_PG20 when
checking the quirk -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Separate the memory configuration to chip-specific structures and
implement dynamic memory for wl128x.
This feature allows us to move TX memory blocks to the RX pool when
the RX path is overloaded.
Thanks for Arik Nemtsov <arik@wizery.com> for helping simplify the
wl1271_fw_status() code.
[Rewrote the commit subject and message for clarity; improved some
comments and changed "spare" to "padding" for consistency; added a
FIXME for the AP memory configuration -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Boot sequence support FREF clock and TCXO clock.
WL128x has two clocks input - TCXO and FREF.
TCXO is the main clock of the device, while FREF is used to sync
between the GPS and the cellular modem.
Auto-detection checks where TCXO is 32.736MHz or 16.368MHz, in that
case the FREF will be used as the WLAN/BT main clock.
[Use clock enumeration as defined in linux/wl12xx.h; remove
unnecessary else block in wl128x_switch_fref; remove unnecessary
change in main.c; remove some unnecessary debug prints and comments;
fix potential use of uninitialized value (pll_config) -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Take care of FW & NVS with the auto-detection between wl127x and
wl128x.
[Moved some common code outside if statements and added notes about
NVS structure assumptions; Fixed a bug when checking the nvs size: if
the size was incorrect, the local nvs variable was set to NULL, it
should be wl->nvs instead. -- Luca]
[Merged with potential buffer overflow fix -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
New general and radio parameters structures and functions.
Implemented as separate functions due to auto-detection
between wl127x and wl128x.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add the the set_block_size op in the SDIO and in the SPI modules.
Since it is only used with SDIO, just explicitly set the op to NULL in
spi.c
Signed-off-by: Luciano Coelho <coelho@ti.com>
New acx command that sets: Rx fifo enable reduced bus transactions
in RX path. Tx bus transactions padding to SDIO block size that
improve preference in Tx and essential for working with SDIO HS (48Mhz).
The max SDIO block size is 256 when working with Tx bus transactions
padding to SDIO block.
Add new ops to SDIO & SPI that handles the win size change in case of
transactions padding (relevant only for SDIO).
[Fix endianess issues; simplify sdio-specific block_size handling;
minor changes in comments; use "aligned_len" in one calculation
instead of "pad" to avoid confusion -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Definitions to support wl128x:
- New FW file name
- Chip ID
- New PLL Configuration Algorithm macros that will be used at wl128x
boot stage
- Rename NVS macro name: wl127x and wl128x are using the same NVS
file name. However, the ini parameters between them are
different. The driver will validate the correct NVS size in
wl1271_boot_upload_nvs().
[Cleaned up some of the definitions. -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In order to prevent overran of IRQ polarity via FW the polarity setting move after
FW download and before IRQ enable.
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When testing some new P2P code, Angie found that the
driver might crash because the beacon command ended
up being bigger than a regular command. This is quite
obvious -- a normal command is limited to roughly 360
bytes but a beacon may be much larger of course.
To fix this, use the huge command buffer.
Reported-by: Angie Chinchilla <angie.v.chinchilla@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since huge commands all share a single buffer,
there can only be a single one in flight at a
time since otherwise they'd overwrite each
other. This is true in the driver now, but it
seems like a possible source of bugs, so add
a test to verify that huge commands are always
sent synchronously.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
There are a number of things in the driver that
may result in a BUG(), which is suboptimal since
it's hard to get debugging information out of
the driver in that case and the user experience
is also not good :-)
Almost all BUG_ON instances can be converted to
WARN_ON with a few lines of appropriate error
handling, so do that instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For some reason, sending QoS configuration causes transmission to stop
after a single frame on HT channels when not associated. Removing the
extra QoS configuration has no effect on station mode, and fixes
injection mode.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Some customers use 0x6C world regulatory domain and this patch
adds the support.
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In http://lkml.indiana.edu/hypermail/linux/kernel/1104.1/01955.html, Geerti
Uytterhoeven reports the following warnings for the rtlwifi drivers.
src/drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c: warning:
'cck_index' may be used uninitialized in this function: => 637
src/drivers/net/wireless/rtlwifi/rtl8192c/dm_common.c: warning:
'cck_index_old' may be used uninitialized in this function: => 637
src/drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c: warning:
'box_extreg' may be used uninitialized in this function: => 303
src/drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c: warning:
'box_reg' may be used uninitialized in this function: => 303
src/drivers/net/wireless/rtlwifi/rtl8192ce/rf.c: warning:
'chnlgroup' may be used uninitialized in this function: => 205
src/drivers/net/wireless/rtlwifi/rtl8192ce/rf.c: warning:
'u4_regvalue' may be used uninitialized in this function: => 450
src/drivers/net/wireless/rtlwifi/rtl8192cu/hw.c: warning:
'hq_sele' may be used uninitialized in this function: => 924
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old function name sounds like checking for existing BA
stream. The function actually checks if we have room for
creating new BA stream or not.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some function parameters become useless after previous
cleanup changes.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return statement at the last line of a void function
is not necessary.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) remove mwifiex_alloc_fill_wait_queue() and
mwifiex_request_ioctl()
2) avoid dynamic allocation of wait queue
3) remove unnecessary mwifiex_error_code macros that
were used mainly by the wait queue status code
4) remove some abstraction functions
5) split mwifiex_prepare_cmd() to mwifiex_send_cmd_async()
and mwifiex_send_sync() to handle asynchronous and
synchronous commands respectively
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are two variants of AR5312 dual-band devices, one single-radio
and the other one dual-radio. On the dual-radio board, the first MAC
only supports 5 GHz, even though it has a dual-band PHY. The 2.4 GHz
part of this phy is used in pass-through mode, connecting the second
MAC with the second PHY.
Disable 2.4 GHz for the first MAC on an AR5312, but only if the board
configuration indicates a dual-radio device.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
EEPROM version 5.0 adds a new field for disabling AES support, having
an older version means that AES is present. This patch fixes hw AES
crypto support on AR5312 boards, which have an older EEPROM version.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AHB, the calibration data usually does not contain a valid MAC address,
the correct MAC address is stored in the board config.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This struct is not used in any common code, and moving it out of
the ath header makes it easier to add more driver specific ops.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On a dual-radio dual-band AR5312 device, the calibration data is shared
between the 5 GHz and the 2.4 GHz radio/MAC.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Request a re-configuration of Beacon related timers
on the receipt of the first Beacon frame has to be set only
for station mode. Setting beacon sync for IBSS is causing
wrong beacon slot selection on beacon generation.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise, you get this:
CC [M] drivers/net/wireless/ath/ath9k/hif_usb.o
drivers/net/wireless/ath/ath9k/hif_usb.c: In function ‘ath9k_skb_queue_complete’:
drivers/net/wireless/ath/ath9k/hif_usb.c:230:12: error: expected expression before ‘do’
make[2]: *** [drivers/net/wireless/ath/ath9k/hif_usb.o] Error 1
make[1]: *** [drivers/net/wireless/ath/ath9k] Error 2
make: *** [drivers/net/wireless/ath/] Error 2
The TX_STAT_INC macro should probably be changed to accomodate such
usage, although using a trinary operator in place of an if-else seems
questionable to me anyway.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Sujith Manoharan <Sujith.Manoharan@Atheros.com>
Arik Nemtsov