Readers/Writers lock for SW timecounter was acquired without disabling
interrupts on local CPU.
The problematic scenario:
* HW timestamping is enabled
* Timestamp overflow periodic service task is running on local CPU and
holding write_lock for SW timecounter
* Completion arrives, triggers interrupt for local CPU.
Interrupt routine calls napi_schedule(), which triggers rx/tx
skb process.
An attempt to read SW timecounter using read_lock is done, which is
already locked by a writer on the same CPU and cause soft lockup.
Add irqsave/irqrestore for when using the readers/writers lock for
writing.
Fixes: ef9814deaf ('net/mlx5e: Add HW timestamping (TS) support')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool LRO enable/disable is broken, as of today we only modify TCP
TIRs in order to apply the requested configuration.
Hardware requires that all TIRs pointing to the same RQ should share the
same LRO configuration. For that all other TIRs' LRO fields must be
modified as well.
Fixes: 5c50368f38 ('net/mlx5e: Light-weight netdev open/stop')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the MLX5E_CQ_HAS_CQES optimization flag, the following buggy
flow might occur:
- Suppose RX is always busy, TX has a single packet every second.
- We poll a single TX cqe and clear its flag.
- We never arm it again as RX is always busy.
- TX CQ flag is never changed, and new TX cqes are not polled.
We revert this optimization.
Fixes: e586b3b0ba ('net/mlx5: Ethernet Datapath files')
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid double mapping of io mapped memory, Device page may be
mapped to non-cached(NC) or to write-combining(WC).
The code before this fix tries to map it both to WC and NC
contrary to what stated in Intel's software developer manual.
Here we remove the global WC mapping of all UARS
"dev->priv.bf_mapping", since UAR mapping should be decided
per UAR (e.g we want different mappings for EQs, CQs vs QPs).
Caller will now have to choose whether to map via
write-combining API or not.
mlx5e SQs will choose write-combining in order to perform
BlueFlame writes.
Fixes: 88a85f99e5 ('TX latency optimization to save DMA reads')
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Reviewed-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling mlx5e_set_coalesce while the interface is down will result in
modifying CQs that don't exist.
Fixes: f62b8bb8f2 ('net/mlx5: Extend mlx5_core to support ConnectX-4
Ethernet functionality')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CQ moderation is not supported by the device, print a warning on
netdevice load, and return error when trying to modify/query cq
moderation via ethtool.
Fixes: f62b8bb8f2 ('net/mlx5: Extend mlx5_core to support ConnectX-4
Ethernet functionality')
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By its role, there is no need to set all the other parameters
for the drop RQ.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For data cache locality considerations, we moved the nop and
csum_offload_inner within sq_stats struct as they are more
commonly accessed in xmit path.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of the pair (channel, tc), we now use a single number that
goes over all tx queues of a TC, for all TCs.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
More proper to declare carrier state UP only after the channels
are ready for traffic.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only need to flush the irq handler to make sure it does not
queue a work into the global work queue after we start to flush it.
So using synchronize_irq() is more appropriate than a spin lock.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow a user to split or unsplit a port using the newly introduced
devlink ops.
Once split, the original netdev is destroyed and 2 or 4 others are
created, according to user configuration. The new ports are like any
other port, with the sole difference of supporting a lower maximum
speed. When unsplit, the reverse process takes place.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When splitting and unsplitting we'll destroy usable ports on the fly, so
mark them using a NULL pointer to indicate that their local port number
is free and can be re-used.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port netdevs are each associated with a different local port number
in the device. These local ports are grouped into groups of 4 (e.g.
(1-4), (5-8)) called clusters. The cluster constitutes the one of two
possible modules they can be mapped to. This mapping is board-specific
and done by the device's firmware during init.
When splitting a port by 4, the device requires us to first unmap all
the ports in the cluster and then map each to a single lane in the module
associated with the port netdev used as the handle for the operation.
This means that two port netdevs will disappear, as only 100Gb/s (4
lanes) ports can be split and we are guaranteed to have two of these
((1, 3), (5, 7) etc.) in a cluster.
When unsplit occurs we need to reinstantiate the two original 100Gb/s
ports and map each to its origianl module. Therefore, during driver init
store the initial local port to module mapping, so it can be used later
during unsplitting.
Note that a by 2 split doesn't require us to store the mapping, as we
only need to reinstantiate one port whose module is known.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When splitting a port we replace it with 2 or 4 other ports. To be able
to do that we need to remove the original port netdev and unmap it from
its module. However, we first mark it as disabled, as active ports
cannot be unmapped.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add middle layer in mlxsw core code to forward port split/unsplit calls
into specific ASIC drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement newly introduced devlink interface. Add devlink port instances
for every port and set the port types accordingly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, there has been an mlx4-specific sysfs file allowing user to
change port type to either Ethernet of InfiniBand. This is very
inconvenient.
Allow to expose the same ability to set port type in a generic way
using devlink interface.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement newly introduced devlink interface. Add devlink port instances
for every port and set the port types accordingly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
v2->v3:
-add dev param to devlink_register (api change)
Signed-off-by: David S. Miller <davem@davemloft.net>
Mlx5's mkey mechanism is also used for memory windows.
The current code base uses MR (memory region) naming, which is
inaccurate. Changing MR to mkey in order to represent its different
usages more accurately.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Added helper function to read IB standard error counters
via the PPCNT register.
The PPCNT register read command provides the 32-bit error counters
of both IB/RoCE link layer and transport layer.
Signed-off-by: Meny Yossefi <menyy@mellanox.com>
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add support for receiving multicast/unicast traffic with
the don't trap rule.
Sniffing these packets requires a flow steering rule of type NORMAL
at priority 0 with flag IB_FLOW_ATTR_FLAGS_DONT_TRAP set.
Choosing between multicast or unicast is done via ethernet L2 dest_mac
mask and value:
- If mask is all zeros - unicast and multicast are set.
- If mask non zero - only mask with multicast bit 1 and rest 0 is
supported, the mac value will choose if it is
multicast or unicast rule.
If the mask multicast bit is on and some other bits are on too, it means
a request for specific multicast or unicast, this is not supported,
either receive all multicast or all unicast.
Only when limitations are met registered QP will receive requested type
but other QPs can receive same traffic if registered for it.
Otherwise, if limitations are not met, an error will be returned.
Limitations:
- Rule must be with priority 0.
- A0 mode is not supported.
- Sniffer QP cannot appear in any other flow steering rule.
Signed-off-by: Marina Varshaver <marinav@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add TSO and TX checksum counters for tunneled, inner packets
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for TSO and TX checksum when using hw assisted,
tunneled offloads.
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a VXLAN udp dport is added to device it will:
- Configure the hardware to offload the port (up to the max
supported).
- Advertise NETIF_F_GSO_UDP_TUNNEL and supported hw_enc_features.
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add ifndef to en.h. needed for upcoming vxlan patchset.
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use checksum complete for all IP packets, unless they are HW LRO,
in which case, use checksum unnecessary.
Signed-off-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement set/get WOL by ethtool and added the needed
device commands and structures to mlx5_ifc.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for DCBNL IEEE get/set max rate.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the set/get DCBNL IEEE PFC callbacks.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support the ndo_setup_tc callback and the needed methods
for multi TC/UP support, and removed the default_vlan_prio
from mlx5e_priv which is always 0, it was replaced with
hardcoded "0" in the new select queue method.
For that we now create MAX_NUM_TC num of TISs (one per prio)
on netdevice creation instead of priv->params.num_tc which
was always 1.
So far each channel had a single TXQ, Now each channel has a
TXQ per TC (Traffic Class).
Added en_dcbnl.c which implements the set/get DCBNL IEEE ETS,
set/get dcbx and registers the mlx5e dcbnl ops.
We still use the kernel's default TXQ selection method to select the
channel to transmit through but now we use our own method to select
the TXQ inside the channel based on VLAN priority.
In mlx5, as opposed to mlx4, tc group N gets lower priority than
tc group N+1.
CC: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add access functions to set and query a physical port TC groups
and prio parameters.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add access functions to set and query a physical port PFC
(Priority Flow Control) parameters.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the device physical port access functions are implemented in the
port.c file.
We just extract the exposure of these functions from driver.h into a
dedicated header file called port.h.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Looks like a lot, but mostly driver fixes scattered all over as usual.
Of note:
1) Add conditional sched in nf conntrack in cleanup to avoid NMI
watchdogs. From Florian Westphal.
2) Fix deadlock in nfnetlink cttimeout, also from Floarian.
3) Fix handling of slaves in bonding ARP monitor validation, from Jay
Vosburgh.
4) Callers of ip_cmsg_send() are responsible for freeing IP options,
some were not doing so. Fix from Eric Dumazet.
5) Fix per-cpu bugs in mvneta driver, from Gregory CLEMENT.
6) Fix vlan handling in mv88e6xxx DSA driver, from Vivien Didelot.
7) bcm7xxx PHY driver bug fixes from Florian Fainelli.
8) Avoid unaligned accesses to protocol headers wrt. GRE, from
Alexander Duyck.
9) SKB leaks and other problems in arc_emac driver, from Alexander
Kochetkov.
10) tcp_v4_inbound_md5_hash() releases listener socket instead of
request socket on error path, oops. Fix from Eric Dumazet.
11) Missing socket release in pppoe_rcv_core() that seems to have
existed basically forever. From Guillaume Nault.
12) Missing slave_dev unregister in dsa_slave_create() error path,
from Florian Fainelli.
13) crypto_alloc_hash() never returns NULL, fix return value check in
__tcp_alloc_md5sig_pool. From Insu Yun.
14) Properly expire exception route entries in ipv4, from Xin Long.
15) Fix races in tcp/dccp listener socket dismantle, from Eric
Dumazet.
16) Don't set IFF_TX_SKB_SHARING in vxlan, geneve, or GRE, it's not
legal. These drivers modify the SKB on transmit. From Jiri Benc.
17) Fix regression in the initialziation of netdev->tx_queue_len.
From Phil Sutter.
18) Missing unlock in tipc_nl_add_bc_link() error path, from Insu Yun.
19) SCTP port hash sizing does not properly ensure that table is a
power of two in size. From Neil Horman.
20) Fix initializing of software copy of MAC address in fmvj18x_cs
driver, from Ken Kawasaki"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (129 commits)
bnx2x: Fix 84833 phy command handler
bnx2x: Fix led setting for 84858 phy.
bnx2x: Correct 84858 PHY fw version
bnx2x: Fix 84833 RX CRC
bnx2x: Fix link-forcing for KR2
net: ethernet: davicom: fix devicetree irq resource
fmvj18x_cs: fix incorrect indexing of dev->dev_addr[] when copying the MAC address
Driver: Vmxnet3: Update Rx ring 2 max size
net: netcp: rework the code for get/set sw_data in dma desc
soc: ti: knav_dma: rename pad in struct knav_dma_desc to sw_data
net: ti: netcp: restore get/set_pad_info() functionality
MAINTAINERS: Drop myself as xen netback maintainer
sctp: Fix port hash table size computation
can: ems_usb: Fix possible tx overflow
Bluetooth: hci_core: Avoid mixing up req_complete and req_complete_skb
net: bcmgenet: Fix internal PHY link state
af_unix: Don't use continue to re-execute unix_stream_read_generic loop
unix_diag: fix incorrect sign extension in unix_lookup_by_ino
bnxt_en: Failure to update PHY is not fatal condition.
bnxt_en: Remove unnecessary call to update PHY settings.
...
When PVID is toggled off on a port member in a VLAN filtering bridge or
the PVID VLAN is deleted, make the port drop untagged packets. Reverse
the operation when PVID is toggled back on.
Set the PVID back to the default (1), when leaving the bridge so that
untagged traffic will be directed to the CPU.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VLAN filtering is enabled on a bridge and PVID is deleted from a
bridge port, then untagged frames are not allowed to ingress into the
bridge from this port.
Add the Switch Port Acceptable Frame Types (SPAFT) register, which
configures the frame admittance of the port.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN device leaves a bridge its STP state is set to DISABLED,
which causes the hardware to discard any packets coming through the port
with this VLAN.
Fix that by setting STP state to FORWARDING when the device leaves its
bridge and allow traffic to be directed to CPU.
Fixes: 26f0e7fb15 ("mlxsw: spectrum: Add support for VLAN devices bridging")
Reported-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MLXSW_PORT_MAX_PORTS represents the maximum number of local ports, which
is 65 for both ASICs (SwitchX-2 and Spectrum) supported by this driver.
Fixes: 93c1edb27f ("mlxsw: Introduce Mellanox switch driver core")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's forbidden to manually change dev->features in run-time. Currently, this is
done in the driver to make sure that GSO_UDP_TUNNEL is advertized only when
VXLAN tunnel is set. However, since the stack actually does features intersection
with hw_enc_features, we can safely revert to advertizing features early when
registering the netdevice.
Fixes: f4a1edd561 ('net/mlx4_en: Advertize encapsulation offloads [...]')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
problem description:
The current code sets UAR page size equal to system page size.
The ConnectX-3 and ConnectX-3 Pro HWs require minimum 128 UAR pages.
The mlx4 kernel drivers are not loaded if there is less than 128 UAR pages.
solution:
Always set UAR page to 4KB. This allows more UAR pages if the OS
has PAGE_SIZE larger than 4KB. For example, PowerPC kernel use 64KB
system page size, with 4MB uar region, there are 4MB/2/64KB = 32
uars (half for uar, half for blueflame). This does not meet minimum 128
UAR pages requirement. With 4KB UAR page, there are 4MB/2/4KB = 512 uars
which meet the minimum requirement.
Note that only codes in mlx4_core that deal with firmware know that uar
page size is 4KB. Codes that deal with usr page in cq and qp context
(mlx4_ib, mlx4_en and part of mlx4_core) still have the same assumption
that uar page size equals to system page size.
Note that with this implementation, on 64KB system page size kernel, there
are 16 uars per system page but only one uars is used. The other 15
uars are ignored because of the above assumption.
Regarding SR-IOV, mlx4_core in hypervisor will set the uar page size
to 4KB and mlx4_core code in virtual OS will obtain the uar page size from
firmware.
Regarding backward compatibility in SR-IOV, if hypervisor has this new code,
the virtual OS must be updated. If hypervisor has old code, and the virtual
OS has this new code, the new code will be backward compatible with the
old code. If the uar size is big enough, this new code in VF continues to
work with 64 KB uar page size (on PowerPc kernel). If the uar size does not
meet 128 uars requirement, this new code not loaded in VF and print the same
error message as the old code in Hypervisor.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PCI channel could go offline during reset due to EEH. Don't bug on in
this case, the error is recoverable.
Fixes: f6bc11e426 ('net/mlx4_core: Enhance the catas flow to support device reset')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error flow in procedure handle_existing_counter() is wrong.
The procedure should exit after encountering the error, not continue
as if everything is OK.
Fixes: 68230242cd ('net/mlx4_core: Add port attribute when tracking counters')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, the shift value used for time-stamping was constant and didn't
depend on the HW chip frequency. Change that to take the frequency into account
and calculate the maximal value in cycles per wraparound of ten seconds. This
time slot was chosen since it gives a good accuracy in time synchronization.
Algorithm for shift value calculation:
* Round up the maximal value in cycles to nearest power of two
* Calculate maximal multiplier by division of all 64 bits set
to above result
* Then, invert the function clocksource_khz2mult() to get the shift from
maximal mult value
Fixes: ec693d4701 ('net/mlx4_en: Add HW timestamping (TS) support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RdropOvflw counts overrun of HW buffer, therefore should
be used for rx_fifo_errors only.
Currently RdropOvflw counter is mistakenly also set into
rx_missed_errors and rx_over_errors too, which makes the
device total dropped packets accounting to show wrong results.
Fix that. Use it for rx_fifo_errors only.
Fixes: c27a02cd94 ('mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC')
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates setup_tc so we can pass additional parameters into
the ndo op in a generic way. To do this we provide structured union
and type flag.
This lets each classifier and qdisc provide its own set of attributes
without having to add new ndo ops or grow the signature of the
callback.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndo_setup_tc() op was added to support drivers offloading tx
qdiscs however only support for mqprio was ever added. So we
only ever added support for passing the number of traffic classes
to the driver.
This patch generalizes the ndo_setup_tc op so that a handle can
be provided to indicate if the offload is for ingress or egress
or potentially even child qdiscs.
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently our netdevice ops is a one static global variable which
is referenced by all mlx5e netdevice instances. This can be
problematic when different driver instances do not share same
HW capabilities (e.g SRIOV PF and VFs probed to the host).
Now we have two constant global netdevice ops variables, one
for basic netdevice ops and the other with extended SRIOV ops,
on netdevice construction we choose the one suitable for
current device capabilities.
Fixes: 66e49dedad ("net/mlx5e: Add support for SR-IOV ndos")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mlx5e_select_queue is redundant since num_tc is always 1.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- One fix to ipoib multicast joins
- One fix to mlx4 error handling
- One fix to mlx5 size computation
- One fix to a thinko in core code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lzqm
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull more rdma fixes from Doug Ledford:
"I think we are getting pretty close to done now. There are four
one-off fixes in this update:
- fix ipoib multicast joins
- fix mlx4 error handling
- fix mlx5 size computation
- fix a thinko in core code"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/mlx5: Fix RC transport send queue overhead computation
IB/ipoib: fix for rare multicast join race condition
IB/core: Fix reading capability mask of the port info class
net/mlx4: fix some error handling in mlx4_multi_func_init()
The while loop after err_slaves should use post-decrement; otherwise
we'll fail to do the kfrees for i==0, and will run into out-of-bounds
accesses if the setup above failed already at i==0.
[I'm not sure why one even bothers populating the ->vlan_filter array:
mlx4.h isn't #included by anything outside
drivers/net/ethernet/mellanox/mlx4/, and "git grep -C2 -w vlan_filter
drivers/net/ethernet/mellanox/mlx4/" seems to suggest that the
vlan_filter elements aren't used at all.]
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pull networking fixes from David Miller:
"This looks like a lot but it's a mixture of regression fixes as well
as fixes for longer standing issues.
1) Fix on-channel cancellation in mac80211, from Johannes Berg.
2) Handle CHECKSUM_COMPLETE properly in xt_TCPMSS netfilter xtables
module, from Eric Dumazet.
3) Avoid infinite loop in UDP SO_REUSEPORT logic, also from Eric
Dumazet.
4) Avoid a NULL deref if we try to set SO_REUSEPORT after a socket is
bound, from Craig Gallek.
5) GRO key comparisons don't take lightweight tunnels into account,
from Jesse Gross.
6) Fix struct pid leak via SCM credentials in AF_UNIX, from Eric
Dumazet.
7) We need to set the rtnl_link_ops of ipv6 SIT tunnels before we
register them, otherwise the NEWLINK netlink message is missing
the proper attributes. From Thadeu Lima de Souza Cascardo.
8) Several Spectrum chip bug fixes for mlxsw switch driver, from Ido
Schimmel
9) Handle fragments properly in ipv4 easly socket demux, from Eric
Dumazet.
10) Don't ignore the ifindex key specifier on ipv6 output route
lookups, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (128 commits)
tcp: avoid cwnd undo after receiving ECN
irda: fix a potential use-after-free in ircomm_param_request
net: tg3: avoid uninitialized variable warning
net: nb8800: avoid uninitialized variable warning
net: vxge: avoid unused function warnings
net: bgmac: clarify CONFIG_BCMA dependency
net: hp100: remove unnecessary #ifdefs
net: davinci_cpdma: use dma_addr_t for DMA address
ipv6/udp: use sticky pktinfo egress ifindex on connect()
ipv6: enforce flowi6_oif usage in ip6_dst_lookup_tail()
netlink: not trim skb for mmaped socket when dump
vxlan: fix a out of bounds access in __vxlan_find_mac
net: dsa: mv88e6xxx: fix port VLAN maps
fib_trie: Fix shift by 32 in fib_table_lookup
net: moxart: use correct accessors for DMA memory
ipv4: ipconfig: avoid unused ic_proto_used symbol
bnxt_en: Fix crash in bnxt_free_tx_skbs() during tx timeout.
bnxt_en: Exclude rx_drop_pkts hw counter from the stack's rx_dropped counter.
bnxt_en: Ring free response from close path should use completion ring
net_sched: drr: check for NULL pointer in drr_dequeue
...
When switchdev drivers process FDB notifications from the underlying
device they resolve the netdev to which the entry points to and notify
the bridge using the switchdev notifier.
However, since the RTNL mutex is not held there is nothing preventing
the netdev from disappearing in the middle, which will cause
br_switchdev_event() to dereference a non-existing netdev.
Make switchdev drivers hold the lock at the beginning of the
notification processing session and release it once it ends, after
notifying the bridge.
Also, remove switchdev_mutex and fdb_lock, as they are no longer needed
when RTNL mutex is held.
Fixes: 03bf0c2812 ("switchdev: introduce switchdev notifier")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx_lane, tx_lane and module fields in the PMLP register don't have
an additional offset besides the base one (0x04), so set it to 0x00.
Fixes: 4ec14b7634 ("mlxsw: Add interface to access registers and process events")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dumping the FDB we can't compare the actual pointers of the ports
structs, as it's possible the struct represents a vPort instead of the
underlying physical port.
Solve this by comparing the local port number instead, as it's shared
between the physical ports and all the vPorts on top of him.
Fixes: 54a732018d ("mlxsw: spectrum: Adjust switchdev ops for VLAN devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAG FDB records can only point to LAG devices or VLAN devices configured
on top of them. Therefore, when dumping the FDB we shouldn't associate
these records with the underlying physical ports.
Fixes: 8a1ab5d766 ("mlxsw: spectrum: Implement FDB add/remove/dump for LAG")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAG FDB entries pointing to VLAN devices should be reported to the
bridge with the matching VLAN device and not the underlying LAG device.
Fixes: aac78a4408 ("mlxsw: spectrum: Adjust FDB notifications for VLAN devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dumping the hardware FDB we should report entries pointing to VLAN
devices with VLAN 0, as packets coming into the bridge are untagged.
Likewise, pass FDB_{ADD,DEL} notifications with VLAN 0 for these
devices.
Fixes: 54a732018d ("mlxsw: spectrum: Adjust switchdev ops for VLAN devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we disable learning on bridge port we should still update the
software bridge's FDB when entry pointing to this bridge port is
aged-out. We can otherwise have an inconsistency between software and
hardware tables.
Fixes: 8a1ab5d766 ("mlxsw: spectrum: Implement FDB add/remove/dump for LAG")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When port is put into LISTENING state it shouldn't populate the FDB, so
set the port's STP state in hardware to DISCARDING instead of LEARNING.
It will therefore keep listening to BPDU packets, but discard other
non-control packets and won't perform any learning.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When STP state is set to DISABLED the port is assumed to be inactive, but
currently we forward packets ingressing through it.
Instead, set the port's STP state in hardware to DISCARDING, which means
it doesn't forward packets or perform any learning, but it does trap
control packets. However, these packets will be dropped by bridge code,
which results in the expected behavior.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in previous commit, we should always take care of flushing
the FDB in the driver and not rely on bridge code.
We need to distinguish between two cases with regards to LAG:
1) Port is leaving LAG while LAG is bridged (or VLAN devices on top of
it). In this case don't flush the FDB entries pointing to the LAG ID, as
this will affect other ports still member in the LAG. Only flush the FDB
when the last port in the LAG is leaving the bridge.
2) LAG device is leaving the bridge. In this case the CHANGEUPPER event
is simply propagated to each member port, so make each port flush the
FDB in its turn.
Note that emptying a bridged LAG from ports creates an inconsistency
between hardware and software. A user who later (< ageing_time)
re-populates the LAG won't have any FDB entries pointing to the LAG ID
in hardware, but they will be present in the software bridge's FDB.
Currently there is no good solution to this problem, but this will be
addressed by us in the future.
In order to optimize the flushing process, flush by port or LAG ID if
there are no VLAN interfaces on top of the port. Otherwise, flush using
(Port / LAG ID, FID=VID} for each of the lower 4K FIDs. In the case of
VLAN device simply flush using {Port / LAG ID, vFID} with the vFID to
which the VLAN device is mapped to.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a net device from a bridge we should flush the FDB entries
associated with this net device. Up until now, we relied upon bridge
code to do that for us, but it is possible for user to prevent hardware
from syncing with the software bridge (learning_sync=0), so we need to
flush overselves.
Add the Switch Filtering DB Flush (SFDF) register that is used to flush
FDB entries according to different parameters (per-port, per-FID etc).
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for a user to remove a port from a LAG device, while the
LAG device or VLAN devices on top of it are bridged. In these cases,
bridge's teardown sequence is never issued, so we need to take care of
it ourselves.
When LAG's unlinking event is received by port netdev:
1) Traverse its vPorts list and make those member in a bridge leave it.
They will be deleted later by LAG code.
2) Make the port netdev itself leave its bridge if member in one.
Fixes: 0d65fc1304 ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Remove usage of ib_query_device and instead store attributes in
ib_device struct
- Move iopoll out of block and into lib, rename to irqpoll, and use
in several places in the rdma stack as our new completion queue
polling library mechanism. Update the other block drivers that
already used iopoll to use the new mechanism too.
- Replace the per-entry GID table locks with a single GID table lock
- IPoIB multicast cleanup
- Cleanups to the IB MR facility
- Add support for 64bit extended IB counters
- Fix for netlink oops while parsing RDMA nl messages
- RoCEv2 support for the core IB code
- mlx4 RoCEv2 support
- mlx5 RoCEv2 support
- Cross Channel support for mlx5
- Timestamp support for mlx5
- Atomic support for mlx5
- Raw QP support for mlx5
- MAINTAINERS update for mlx4/mlx5
- Misc ocrdma, qib, nes, usNIC, cxgb3, cxgb4, mlx4, mlx5 updates
- Add support for remote invalidate to the iSER driver (pushed through the
RDMA tree due to dependencies, acknowledged by nab)
- Update to NFSoRDMA (pushed through the RDMA tree due to dependencies,
acknowledged by Bruce)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5oO7
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"Initial roundup of 4.5 merge window patches
- Remove usage of ib_query_device and instead store attributes in
ib_device struct
- Move iopoll out of block and into lib, rename to irqpoll, and use
in several places in the rdma stack as our new completion queue
polling library mechanism. Update the other block drivers that
already used iopoll to use the new mechanism too.
- Replace the per-entry GID table locks with a single GID table lock
- IPoIB multicast cleanup
- Cleanups to the IB MR facility
- Add support for 64bit extended IB counters
- Fix for netlink oops while parsing RDMA nl messages
- RoCEv2 support for the core IB code
- mlx4 RoCEv2 support
- mlx5 RoCEv2 support
- Cross Channel support for mlx5
- Timestamp support for mlx5
- Atomic support for mlx5
- Raw QP support for mlx5
- MAINTAINERS update for mlx4/mlx5
- Misc ocrdma, qib, nes, usNIC, cxgb3, cxgb4, mlx4, mlx5 updates
- Add support for remote invalidate to the iSER driver (pushed
through the RDMA tree due to dependencies, acknowledged by nab)
- Update to NFSoRDMA (pushed through the RDMA tree due to
dependencies, acknowledged by Bruce)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (169 commits)
IB/mlx5: Unify CQ create flags check
IB/mlx5: Expose Raw Packet QP to user space consumers
{IB, net}/mlx5: Move the modify QP operation table to mlx5_ib
IB/mlx5: Support setting Ethernet priority for Raw Packet QPs
IB/mlx5: Add Raw Packet QP query functionality
IB/mlx5: Add create and destroy functionality for Raw Packet QP
IB/mlx5: Refactor mlx5_ib_qp to accommodate other QP types
IB/mlx5: Allocate a Transport Domain for each ucontext
net/mlx5_core: Warn on unsupported events of QP/RQ/SQ
net/mlx5_core: Add RQ and SQ event handling
net/mlx5_core: Export transport objects
IB/mlx5: Expose CQE version to user-space
IB/mlx5: Add CQE version 1 support to user QPs and SRQs
IB/mlx5: Fix data validation in mlx5_ib_alloc_ucontext
IB/sa: Fix netlink local service GFP crash
IB/srpt: Remove redundant wc array
IB/qib: Improve ipoib UD performance
IB/mlx4: Advertise RoCE v2 support
IB/mlx4: Create and use another QP1 for RoCEv2
IB/mlx4: Enable send of RoCE QP1 packets with IP/UDP headers
...
When modifying a QP, the desired operation was determined in
the mlx5_core using a transition table that takes the current
state, the final state, and returns the desired operation.
Since this logic will be used for Raw Packet QP, move the
operation table to the mlx5_ib.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When the user changes the Address Vector(AV) in the modify QP, he
provides an SL. This SL should be translated to Ethernet Priority
by taking the 3 LSB bits, and modify the QP's TIS according to this
Ethernet priority.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Since Raw Packet QP is composed of RQ and SQ, the IB QP's
state is derived from the sub-objects. Therefore we need
to query each one of the sub-objects, and decide on the
IB QP's state.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When an event arrives on QP/RQ/SQ, check whether it's supported,
and print a warning message otherwise.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
RQ/SQ will be used to implement IB verbs QPs, so the IB QP affiliated
events are affiliated also with SQs and RQs.
Since SQ, RQ and QP resource numbers do not share the same name
space, a queue type field was added to the event data to specify
the SW object that the event is affiliated with.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
To be used by mlx5_ib in the following patches for implementing
RAW PACKET QP.
Add mlx5_core_ prefix to alloc and delloc transport_domain since
they are exposed now.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Enforce working with CQE version 1 when the user supports CQE
version 1 and asked to work this way.
If the user still works with CQE version 0, then use the default
CQE version to tell the Firmware that the user still works in the
older mode.
After this patch, the kernel still reports CQE version 0.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In RoCE v2 we need to choose a source UDP port, we do so by using
entropy over the source and dest QPNs.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In order to support RoCE v2, the hardware needs to be configured
to classify certain UDP packets as RoCE v2 packets and pass it
through its RoCE pipeline. This patch enables configuring this
UDP port.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If the hardware supports RoCE v2 (mixed with RoCE v1) mode, we enable
it. This is necessary in order to support RoCE v2.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Query the RoCE support from firmware using the appropriate firmware
commands. Downstream patches will read these capabilities and act
accordingly.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
With several ConnectX-4 cards installed on a server, one may receive
irqn > 255 from the kernel API, which we mistakenly trim to 8bit.
This causes EQ creation failure with the following stack trace:
[<ffffffff812a11f4>] dump_stack+0x48/0x64
[<ffffffff810ace21>] __setup_irq+0x3a1/0x4f0
[<ffffffff810ad7e0>] request_threaded_irq+0x120/0x180
[<ffffffffa0923660>] ? mlx5_eq_int+0x450/0x450 [mlx5_core]
[<ffffffffa0922f64>] mlx5_create_map_eq+0x1e4/0x2b0 [mlx5_core]
[<ffffffffa091de01>] alloc_comp_eqs+0xb1/0x180 [mlx5_core]
[<ffffffffa091ea99>] mlx5_dev_init+0x5e9/0x6e0 [mlx5_core]
[<ffffffffa091ec29>] init_one+0x99/0x1c0 [mlx5_core]
[<ffffffff812e2afc>] local_pci_probe+0x4c/0xa0
Fixing it by changing of the irqn type from u8 to unsigned int to
support values > 255
Fixes: 61d0e73e0a ('net/mlx5_core: Use the the real irqn in eq->irqn')
Reported-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Doron Tsur <doront@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a missing break statement so we always return -EOPNOTSUPP.
Fixes: 3a49b4fde2 ('mlxsw: Adding layer 2 multicast support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_main.c
drivers/net/ethernet/mellanox/mlxsw/spectrum.h
drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
The bond_main.c and mellanox switch conflicts were cases of
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add exports to flow steering API for mlx5_ib usage.
The following functions are exported:
1. mlx5_create_auto_grouped_flow_table - used to create flow
table with auto flow grouping management (create and destroy
flow groups). In auto-grouped flow tables, we create groups
automatically if needed (if we don't find an existing
flow group with same match criteria when we add new rule).
2. mlx5_destroy_flow_table - used to destroy a flow table.
3. mlx5_add_flow_rule - used to add flow rule into a flow table.
4. mlx5_del_flow_rule - used to delete flow rule from its flow table.
5. mlx5_get_flow_namespace - used to get a handle to the required
namespace sub-tree.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver is loaded, we create flow steering namespace
for kernel bypass with nine priorities and another namespace
for leftovers(in order to catch packets that weren't matched).
Verbs applications will use these priorities.
we found nine as a number that balances the requirements from the
user and retains performance.
The bypass namespace is used by verbs applications that want to bypass
the kernel networking stack. The leftovers namespace is used by verbs
applications and the sniffer in order to catch packets that weren't
handled by any preceding rules.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before we create the sub tree of a steering namespaces(kernel, bypass,
leftovers) we check that the device has the required capabilities
in order to create this subtree.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each priority has two attributes:
1. max_ft - maximum allowed flow tables under this priority.
2. start_level - start level range of the flow tables
in the priority.
These attributes are set by traversing the tree nodes by
DFS and set start level and max flow tables to each priority.
Start level depends on the max flow tables of the prior priorities
in the tree.
The leaves of the trees have max_ft set in them. Each node accumulates
the max_ft of its children and set it accordingly.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow tables from different priorities should be chained together.
When a packet arrives we search for a match in the
by-pass flow tables (first we search for a match in priority 0
and if we don't find a match we move to the next priority).
If we can't find a match in any of the bypass flow-tables, we continue
searching in the flow-tables of the next priority, which are the
kernel's flow tables.
Setting the miss flow table in a new flow table to be the next one in
the list is performed via create flow table API. If we want to change an
existing flow table, for example in order to point from an
existing flow table to the new next-in-list flow table, we use the
modify flow table API.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the modify flow table command. This command is used when
we want to change the next flow table of an existing flow table.
The next flow table is defined as the table we search (in order
to find a match), if we couldn't find a match in any of the flow table
entries in the current flow table.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The root Flow Table for each Flow Table Type is defined,
by default, as the Flow Table with level 0.
In order not to use an empty flow tables and introduce new hops,
but still preserve space for flow-tables that have a priority
greater(lower number) than the current flow table, we introduce this
new set root flow table command.
This command tells the HW to start matching packets from the
assigned root flow table.
This command is used when we create new flow table with level lower than the
current lowest flow table or it is the first flow table.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two utility functions for find next and prev flow table.
Find next flow table function gets priority and return the
first flow table of the next priority in the tree.
Find prev flow table return the last flow table of
the previous priority in the tree.
These utility functions are used for chaining flow table from different
priorities.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When user add rule to autogrouped flow table, we search
for flow group with the same match criteria, if we don't
find such group then we create new flow group with the
required match criteria and insert the rule to this group.
We divide the flow table into required_groups + 1,
in order to reserve a part of the flow table for rules
which don't match any existing group.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dumping the FDB (invoked with a process context) or handling FDB
notifications (polled periodicly in delayed work) might each entail
multiple EMAD transcations due to the number of entries.
While we only allow one EMAD transaction at a time, there is nothing
stopping the dump and notification processing sessions from
interleaving. However, this is forbidden by the hardware, so we need to
make sure only one of these sessions can run at a time.
Solve this by adding a mutex ('fdb_lock'), as both kernel threads can
sleep while waiting for the response EMAD.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add SWITCHDEV_OBJ_ID_PORT_MDB switchdev ops support. On first MDB insertion
creates a new multicast group (MID) and add members port to the MID. Also
add new MDB entry for the flooding-domain (fid-vid) and link the MDB entry
to the newly constructed MC group.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a generic function that translate VID to FID.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding back SMID register definition and packing. For each MC group a new
SMID entry will be generated.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multicast-related records have specific format in SFD register.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It may happen that we get notification for FDB entry for object (port,
lag, vport), which does not exist. Currently we ignore that, which only
causes this being re-sent in next notification. The entry will never
disappear. So get rid of it by simply removing it using SFD register.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not pass struct mlxsw_sp_port to mlxsw_sp_port_fdb_uc_op and rather
just pass local_port. This is needed in case this is called from SFN
process function and mlxsw_sp_port is not existent for particular
local_port.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We checked "err" on the lines before so we know it's zero here.
These cause a static checker warning because checking known things can
indicate a bug. Maybe there is a missing assignment or we are checking
the wrong variable.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a vlan is been configured, remeber the untagged mode of the vlan.
When displaying the list of configured VLANs, show the untagged attribute.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is bridged, the bridge must be vlan aware bridge (.1Q)
or the bridging should be on top of VLAN interfaces (.1D bridge).
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize VLANs 0..4095 (Remove init for VID 4096).
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During initialization, when creating the send descriptor queues (SDQs),
we specify the CPU egress traffic class of each SDQ. The maximum number
of classes of this type is different in the two ASICs supported by this
PCI driver.
New firmware versions check this value is set correctly, which causes
errors on the Spectrum ASIC, as its max exposed egress traffic class is
lower than 7.
Solve this by setting this field to 3, which is an acceptable value for
both ASICs.
Note that we currently do not expose the QoS capabilities of the ASICs,
so setting this to an hardcoded value is OK for now.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a PHC support to the mlx5_en driver. Use reader/writer spinlocks to
protect the timecounter since every packet received needs to call
timecounter_cycle2time() when timestamping is enabled. This can become
a performance bottleneck with RSS and multiple receive queues if normal
spinlocks are used.
The driver has been tested with both Documentation/ptp/testptp and the
linuxptp project (http://linuxptp.sourceforge.net/) on a Mellanox
ConnectX-4 card.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for enable/disable HW timestamping for incoming and/or
outgoing packets. To enable/disable HW timestamping appropriate
ioctl should be used. Currently HWTSTAMP_FILTER_ALL/NONE and
HWTSAMP_TX_ON/OFF only are supported. Make all relevant changes in
RX/TX flows to consider TS request and plant HW timestamps into
relevant structures.
Add internal clock for converting hardware timestamp to nanoseconds. In
addition, add a service task to catch internal clock overflow, to make
sure timestamping is accurate.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A preparation step which adds support for reading the hardware
internal timer and the hardware timestamping from the CQE.
In addition, advertize device_frequency_khz HCA capability.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the SKB is cloned, or has an elevated users count, someone else
can be looking at it at the same time.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge port attributes are offloaded to hardware when invoked with SELF
flag set, but it really makes no sense to reflect them when port is not
bridged.
Allow a user to change these attribute only when port is bridged and
initialize them correctly when joining or leaving a bridge.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the bridge status of physical ports in the appropriate functions, to
be consistent with LAG join/leave and vPorts joining/leaving bridge.
Also, remove the error messages in these two functions, as we already
emit errors in both the single functions they call.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for us to fail when joining or leaving a bridge, so let
the user know about that by returning NOTIFY_BAD, as already done for
LAG join/leave and 802.1D bridges.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We set PVID to 1 in mlxsw_sp_port_vlan_init(), so we can remove this
statement.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW is capable of 2 requestor endianness modes for standard 8 Bytes
atomic: BE (0x0) and host endianness (0x1). Read the supported modes
from hca atomic capabilities and configure HW to host endianness mode if
supported.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
A mlx5 Ethernet port must be explicitly enabled for RoCE.
When RoCE is not enabled on the port, the NIC will refuse to create
QPs attached to it and incoming RoCE packets will be considered by the
NIC as plain Ethernet packets.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Introduce a new function called mlx5_query_nic_vport_context().
This function gets all the NIC vport attributes from the device.
The MAC address is just one of the NIC vport attributes, so
mlx5_query_nic_vport_mac_address() is now just a wrapper function
above mlx5_query_nic_vport_context().
More NIC vport attributes will be used in following commits.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
KASan reported use-after-free for the hwmon structure. So fix this by
using devm_kzalloc and let the core take care about freeing the memory
during device dettach.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 89309da39 ("mlxsw: core: Implement temperature hwmon interface")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add another sysfs hwmon attribute to expose possibility to reset
temperature sensors history.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_init_timestamp was called before creation of netdev and port
init, thus used uninitialized values. Specifically - NIC frequency was
incorrect causing wrong calculations and later wrong HW timestamps.
Fixes: 1ec4864b10 ('net/mlx4_en: Fixed crash when port type is changed')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Marina Varshaver <marinav@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Service task is responsible for other tasks in addition to timestamping
overflow check. Launch it even if timestamping is not supported by device.
Fixes: 07841f9d94 ('net/mlx4_en: Schedule napi when RX buffers allocation fails')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix uninitialized variable warnings in nfnetlink_queue, a lot of
people reported this... From Arnd Bergmann.
2) Don't init mutex twice in i40e driver, from Jesse Brandeburg.
3) Fix spurious EBUSY in rhashtable, from Herbert Xu.
4) Missing DMA unmaps in mvpp2 driver, from Marcin Wojtas.
5) Fix race with work structure access in pppoe driver causing
corruptions, from Guillaume Nault.
6) Fix OOPS due to sh_eth_rx() not checking whether netdev_alloc_skb()
actually succeeded or not, from Sergei Shtylyov.
7) Don't lose flags when settifn IFA_F_OPTIMISTIC in ipv6 code, from
Bjørn Mork.
8) VXLAN_HD_RCO defined incorrectly, fix from Jiri Benc.
9) Fix clock source used for cookies in SCTP, from Marcelo Ricardo
Leitner.
10) aurora driver needs HAS_DMA dependency, from Geert Uytterhoeven.
11) ndo_fill_metadata_dst op of vxlan has to handle ipv6 tunneling
properly as well, from Jiri Benc.
12) Handle request sockets properly in xfrm layer, from Eric Dumazet.
13) Double stats update in ipv6 geneve transmit path, fix from Pravin B
Shelar.
14) sk->sk_policy[] needs RCU protection, and as a result
xfrm_policy_destroy() needs to free policies using an RCU grace
period, from Eric Dumazet.
15) SCTP needs to clone ipv6 tx options in order to avoid use after
free, from Eric Dumazet.
16) Missing kbuild export if ila.h, from Stephen Hemminger.
17) Missing mdiobus_alloc() return value checking in mdio-mux.c, from
Tobias Klauser.
18) Validate protocol value range in ->create() methods, from Hannes
Frederic Sowa.
19) Fix early socket demux races that result in illegal dst reuse, from
Eric Dumazet.
20) Validate socket address length in pptp code, from WANG Cong.
21) skb_reorder_vlan_header() uses incorrect offset and can corrupt
packets, from Vlad Yasevich.
22) Fix memory leaks in nl80211 registry code, from Ola Olsson.
23) Timeout loop count handing fixes in mISDN, xgbe, qlge, sfc, and
qlcnic. From Dan Carpenter.
24) msg.msg_iocb needs to be cleared in recvfrom() otherwise, for
example, AF_ALG will interpret it as an async call. From Tadeusz
Struk.
25) inetpeer_set_addr_v4 forgets to initialize the 'vif' field, from
Eric Dumazet.
26) rhashtable enforces the minimum table size not early enough,
breaking how we calculate the per-cpu lock allocations. From
Herbert Xu.
27) Fix FCC port lockup in 82xx driver, from Martin Roth.
28) FOU sockets need to be freed using RCU, from Hannes Frederic Sowa.
29) Fix out-of-bounds access in __skb_complete_tx_timestamp() and
sock_setsockopt() wrt. timestamp handling. From WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (117 commits)
net: check both type and procotol for tcp sockets
drivers: net: xgene: fix Tx flow control
tcp: restore fastopen with no data in SYN packet
af_unix: Revert 'lock_interruptible' in stream receive code
fou: clean up socket with kfree_rcu
82xx: FCC: Fixing a bug causing to FCC port lock-up
gianfar: Don't enable RX Filer if not supported
net: fix warnings in 'make htmldocs' by moving macro definition out of field declaration
rhashtable: Fix walker list corruption
rhashtable: Enforce minimum size on initial hash table
inet: tcp: fix inetpeer_set_addr_v4()
ipv6: automatically enable stable privacy mode if stable_secret set
net: fix uninitialized variable issue
bluetooth: Validate socket address length in sco_sock_bind().
net_sched: make qdisc_tree_decrease_qlen() work for non mq
ser_gigaset: remove unnecessary kfree() calls from release method
ser_gigaset: fix deallocation of platform device structure
ser_gigaset: turn nonsense checks into WARN_ON
ser_gigaset: fix up NULL checks
qlcnic: fix a timeout loop
...
When creating a VLAN device on top of LAG, we are basically creating a
vPort on top of each of the port netdevs member in the LAG. Therefore,
these vPorts should inherit both the LAG status and LAG ID from the
underlying port netdevs.
In addition, when the VLAN device joins or leaves a bridge each of the
underlying vPorts should know about it and act accordingly. This is
achieved by propagating the VLAN event down to the lower devices.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding or removing FDB records of VLAN devices on top of LAG we
should set the lag_vid parameter to the VLAN ID of the VLAN device. It
is reserved otherwise.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unicast LAG records in the Switch Filtering Database (SFD) register have
a lag_vid field indicating the VLAN ID in case of vFIDs. This field is
no longer reserved since we are going to add support for VLAN devices on
top of LAG.
Add the lag_vid field to be used by VLAN devies on top of LAG.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the member VLAN devices in a bridge need to share the same vFID.
To achieve that, expand the vFID struct to include the associated bridge
device (or lack of) and allow one to lookup a vFID based on a bridge
device.
When joining a bridge, lookup the relevant vFID or create one if none
exists. Next, make the VLAN device use the vFID.
Leaving a bridge can either occur because a user removed the VLAN device
from a bridge or because the VLAN device was deleted by the user. In the
latter case the bridge's teardown sequence is invoked after the hardware
vPort is already gone. Therefore, when unlinking the VLAN device from
the real device, check if the associated vPort is bridged and act
accordingly. The bridge's notification will be ignored in this case.
Note that bridging a VLAN interface with an ordinary port netdev is
currently not supported, but not forbidden. This will be addressed in a
follow-up patchset.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN interface is configured on top of a physical port we should
associate the VLAN device with the matching vPort. Likewise, when it's
removed, we should revert back to the underlying port netdev.
While not a must, this is consistent with port netdevs and also provides
a more accurate error printing via netdev_err() and friends.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FDB notifications contain the FID and port (or LAG ID) on which the MAC
was learned. In the case of the 802.1Q bridge one can easily derive the
matching VID - as FID equals VID - and generate the appropriate
notification for the software bridge. With VLAN devices this is no
longer the case, as these are associated with a vFID.
Solve that by converting the FID to a vFID and lookup the matching VLAN
device. From that derive the VID and whether learning (and learning
sync) should occur.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
switchdev ops can now be called for VLAN devices and we need to be
prepared for it. Until now they were only called for the port netdev.
Use the newly propagated orig_dev passed as part of the switchdev
attr/obj and determine whether the original device is a VLAN device. If
so, act accordingly, otherwise continue as usual.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Spectrum ASIC - unlike SwitchX-2 - FDB access is done by
specifying FID as parameter and not VID.
Change the relevant variables and parameters names to reflect that.
Note that this was OK up until now, since FID was always equal to VID,
but with the introduction of VLAN interfaces this is no longer the case.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We previously used only one flood table for packets classified to vFIDs.
However, since we are going to add support for bridges between VLAN
interfaces (mapped to vFIDs) we need to add one more flood table.
That way we can separate the flooding domain of unknown unicast traffic
from all the rest and support flood control (as we do with the 802.1Q
bridge).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __mlxsw_sp_port_flood_set function is now used to configure flooding
for both FIDs and vFIDs, so change the parameter name to 'idx' instead
of 'fid'. This is also consistent with hardware documentation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we used a 1:1 mapping - based on VID - to map a VLAN
interface to a vFID. However, a different scheme is needed in order to
support bridges between VLAN interfaces, as all the member interfaces -
which can have different VIDs - need to share the same vFID.
Solve that by splitting the vFID range in two:
1. Non-bridged VLAN interfaces
2. Bridged VLAN interfaces
When a VLAN interface is created, assign it the next available vFID in
the first range, unless one already exists for that VID or number of
vFIDs in the range was exceeded. When interface is removed, free the
vFID, unless other interfaces are mapped to it.
To accomplish the above:
1. Store the VID to vFID mapping in a new struct (mlxsw_sp_vfid), which
has a global context and holds a reference count.
2. Create a vPort (dummy in case of bridge SELF invocation) on top of
of the physical port and hold a reference to the associated vFID.
vfid vfid
+-------------+ +-------------+
| vfid | | vfid |
| vid +---> ... | vid |
| nr_vports | | nr_vports |
+------+------+ +------+------+
|
+-----------------------+-------+
| |
vport vport
+-------------+ +-------------+
| ... | | ... |
| *vfid +---> ... | *vfid +---> ...
| ... | | ... |
+------+------+ +------+------+
| |
port port
+-------------+ +-------------+
| ... | | ... |
| vports_list | | vports_list |
| ... | | ... |
+-------------+ +-------------+
swXpY swXpZ
Next patches in the series will add the missing infrastructure for the
second range and transfer vPorts between the two ranges according to the
received notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for bridges between VLAN interfaces, we'll introduce
a new entity called a vPort, which is a represntation of the VLAN
interface in the hardware.
The main difference between a vPort and a physical port is that several
FIDs can be bound to the latter, whereas only one (called a vFID) can be
bound to the first.
Therefore, it makes sense to use the same struct to represent the two,
but to only allocate the 'active_vlans' bitmap in case of a physical
port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function can return negative values, so its result should
be assigned to signed variable.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Fixes: fc48866f7 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sensor index should be passed instead of 0. For now, this does not make
a difference, since there is so far only one temperature sensor
exposed by HW.
Fixes: 89309da39 ("mlxsw: core: Implement temperature hwmon interface")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix copy & paste error in MTPM unpack helper.
Fixes: 85926f8770 ("mlxsw: reg: Add definition of temperature management registers")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename en_flow_table.c to en_fs.c in order to be aligned
with the new flow steering files.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose the new flow steering API and remove the old
one.
Few changes are required:
1. The Ethernet flow steering follows the existing implementation, but uses
the new steering API. The old flow steering implementation is removed.
2. Move the E-switch FDB management to use the new API.
3. When driver is loaded call to mlx5_init_fs which initialize
the flow steering tree structure, open namespaces for NIC receive
and for E-switch FDB.
4. Call to mlx5_cleanup_fs when the driver is unloaded.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow steering initialization is based on static tree which
illustrates the flow steering tree when the driver is loaded. The
initialization considers the max supported flow table level of the device,
a minimum of 2 kernel flow tables(vlan and mac) are required to have
kernel flow table functionality.
The tree structures when the driver is loaded:
root_namespace(receive nic)
|
priority-0 (kernel priority)
|
namespace(kernel namespace)
|
priority-0 (flow tables priority)
In the following patches, When the EN driver will use the flow steering
API, it create two flow tables and their flow groups under
priority-0(flow tables priority).
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introducing the following objects:
mlx5_flow_root_namespace: represent the root of specific flow table
type tree(e.g NIC receive, FDB, etc..)
mlx5_flow_group: define the mask of the flow specification.
fs_fte(flow steering flow table entry): defines the value of the
flow specification.
The following describes the relationships between the tree objects:
root_namespace --> priorities -->namespaces -->
priorities -->flow-tables --> flow-groups -->
flow-entries --> destinations
When we create new object(flow table/flow group/flow table entry), we
call to the FW command and then we add the related sw object to the tree.
When we destroy object, e.g. call to mlx5_destroy_flow_table, we use
the tree node destructor for destroying the FW object and remove the
node from the tree.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the flow steering mlx5_flow_namespace (Namespace)
and fs_prio (Flow Steering Priority) tree nodes.
Namespaces are used in order to isolate different usages or types
of steering (for example, downstream patches will add a different
namespaces for the NIC driver and for E-Switch FDB usages).
Flow Steering Priorities are objects that describes priorities
ranges between different flow objects under the same namespace.
Example, entries in priority i are matched before entries
in priority i+1.
This patch adds the following algorithms:
1) Calculate level:
Each flow table has level(the priority between the flow tables).
When we initialize the flow steering tree, we assign range of levels
to each priority, therefore the level for new flow table is
the location within the priority related to the range of the priority.
2) Match between match criteria. This function is used
for searching flow group when new flow rule is added.
3) Match between match values. This function is used
for searching flow table entry when new flow rule is added.
4) Add essential macros for traversing on a node's children.
E.g. traversing on all the flow table of some priority
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introducing the base data structure and its operations that are
going to represent ConnectX-4 Flow Steering, this data structure
is basically a tree and all Flow steering objects such as
(Flow Table/Flow Group/FTE/etc ..) are represented as fs_node(s).
fs_node is the base object which describes a basic tree node, with the
following extra info:
type: describes the runtime type of the node (Object).
lock: lock this node sub-tree.
ref_count: number of children + current references.
remove_func: a generic destructor.
fs_node types will be used and explained once the usage is added in the
following patches.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new Flow Steering (FS) firmware commands,
in-order to support the new flow steering infrastructure.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under SRIOV there might be a case where VFs are loaded
without pre-assigned MAC address. In this case, the VF
will randomize its own MAC. This will address the case
of administrator not assigning MAC to the VF through
the PF OS APIs and keep udev happy.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
E-Switch capabilities should be queried only if E-Switch flow table
is supported and not only when vport group manager.
Fixes: d6666753c6 ("net/mlx5: E-Switch, Introduce HCA cap and E-Switch vport context")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already know "err" is zero so there is no need to check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "err = " assignment is missing here.
Fixes: 0d65fc1304 ('mlxsw: spectrum: Implement LAG port join/leave')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eran Ben Elisha