Tegra210 CSI hardware internally uses PLLD for internal test pattern
generator logic.
PLLD_BASE register in CAR has a bit CSI_CLK_SOURCE to enable PLLD
out to CSI during TPG mode.
This patch adds this CSI TPG clock gate to Tegra210 clock driver
to allow Tegra video driver to ungate CSI TPG clock during TPG mode
and gate during non TPG mode.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
We're going to use the generic cpufreq-dt driver on Tegra30 and thus CCLK
intermediate re-parenting will be performed by the clock driver. There is
now special CCLK implementation that supports all CCLK quirks, this patch
makes Tegra30 SoCs to use that implementation.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Jasper Korten <jja2000@gmail.com>
Tested-by: David Heidelberg <david@ixit.cz>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
We're going to use the generic cpufreq-dt driver on Tegra20 and thus CCLK
intermediate re-parenting will be performed by the clock driver. There is
now special CCLK implementation that supports all CCLK quirks, this patch
makes Tegra20 SoCs to use that implementation.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Jasper Korten <jja2000@gmail.com>
Tested-by: David Heidelberg <david@ixit.cz>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
CCLK should be re-parented away from PLLX if PLLX's rate is changing.
The PLLP parent is a common safe CPU parent for all Tegra SoCs, thus
CCLK will be re-parented to PLLP before PLLX rate-change begins and then
switched back to PLLX after the rate-change completion. This patch adds
helper functions which perform CCLK re-parenting, these helpers will be
utilized by further patches.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Jasper Korten <jja2000@gmail.com>
Tested-by: David Heidelberg <david@ixit.cz>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There is a need to temporarily re-parent CCLK away from PLLX if PLLX's
rate is about to change. The newly introduced PLL pre/post rate-change
hooks allow to handle such case.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Jasper Korten <jja2000@gmail.com>
Tested-by: David Heidelberg <david@ixit.cz>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
CCLK stands for "CPU Clock", CPU core is running off CCLK. CCLK supports
multiple parents, it has internal clock divider and a clock skipper.
PLLX is the main CCLK parent that provides clock rates above 1GHz and it
has special property such that the CCLK's internal divider is set into
bypass mode when PLLX is selected as a parent for CCLK.
This patch forks generic Super Clock into CCLK implementation which takes
into account all CCLK specifics. The proper CCLK implementation is needed
by the upcoming Tegra20 CPUFreq driver update that will allow to utilize
the generic cpufreq-dt driver by moving intermediate clock selection into
the clock driver.
Note that technically this patch could be squashed into clk-super.c, but
it is cleaner to have a separate source file. Also note that currently all
CCLKLP bits are left in the clk-super.c and only CCLKG is supported by
clk-tegra-super-cclk. It shouldn't be difficult to move the CCLKLP bits,
but CCLKLP is not used by anything in kernel and thus better not to touch
it for now.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Jasper Korten <jja2000@gmail.com>
Tested-by: David Heidelberg <david@ixit.cz>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove the old emc_mux clock and don't use the common EMC clock
definition. This will be replaced by a new clock defined in the
EMC driver.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The EMC clock needs to carefully coordinate with the EMC controller
programming to make sure external memory can be properly clocked. Do so
by hooking up the EMC clock with an EMC provider that will specify which
rates are supported by the EMC and provide a callback to use for setting
the clock rate at the EMC.
Based on work by Peter De Schrijver <pdeschrijver@nvidia.com>.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Export functions to allow accessing the CAR register required by EMC
clock scaling. These functions will be used to access the CAR register
as part of the scaling sequence.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Introduce the low jitter path of PLLP and PLLMB which can be used as EMC
clock source.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This code is only used on Tegra124, so rename it accordingly to make it
more consistent with other file names.
While at it, also get rid of the TEGRA_CLK_EMC Kconfig symbol that's
really just an alias for TEGRA124_EMC.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Current clock driver enables PLLA, cdev1 on Tegra20 and extern1 on
Tegra30 and above as a part of clocks init and there is no need to
have these audio clocks enabled by the clock driver.
extern1 is used as parent for clk_out_1 and clk_out_1 is dedicated
for audio mclk on Tegra30 and above Tegra platforms and these clocks
are taken care by ASoC driver.
So, this patch removes audio related clocks configuration from clock
init of Tegra20 and above.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Current Tegra clock driver registers PMC clocks clk_out_1, clk_out_2,
clk_out_3 and 32KHz blink output in tegra_pmc_init() which does direct
PMC register access during clk_ops and these PMC register read and write
access will not happen when PMC is in secure mode.
Any direct PMC register access from non-secure world will not go
through.
All the PMC clocks are moved to Tegra PMC driver with PMC as a clock
provider.
This patch removes tegra_pmc_clk_init along with corresponding clk ids
from Tegra clock driver.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra has no CLK_M_DIV2 and CLK_M_DIV4 clocks and instead it has
OSC_DIV2 and OSC_DIV4 clocks from OSC pads which are the possible
parents of PMC clocks for Tegra30 through Tegra210.
Tegra PMC clock parents are changed to use OSC_DIV clocks.
So, this patch removes CLK_M_DIV fixed clocks
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
OSC is one of the parent for Tegra PMC clocks clk_out_1, clk_out_2,
and clk_out_3.
This patch adds Tegra OSC to clock lookup.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra30 through Tegra210 has OSC_DIV2 and OSC_DIV4 fixed clocks
from the OSC pads.
This patch adds support for these clocks.
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Fixes for clk controllers on qcom msm8998 SoCs
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Adjust composite clk to new way of describing clk parents
- Add a driver for BCLK of Freescale SAI cores
* clk-imx: (32 commits)
clk: imx: Add support for i.MX8MP clock driver
dt-bindings: imx: Add clock binding doc for i.MX8MP
clk: imx: gate4: Switch imx_clk_gate4_flags() to clk_hw based API
clk: imx: imx8mq: Switch to clk_hw based API
clk: imx: imx8mm: Switch to clk_hw based API
clk: imx: imx8mn: Switch to clk_hw based API
clk: imx: Remove __init for imx_obtain_fixed_clk_hw() API
clk: imx: gate3: Switch to clk_hw based API
clk: imx: add hw API imx_clk_hw_mux2_flags
clk: imx: add imx_unregister_hw_clocks
clk: imx: clk-composite-8m: Switch to clk_hw based API
clk: imx: clk-pll14xx: Switch to clk_hw based API
clk: imx7up: Rename the clks to hws
clk: imx: Rename the imx_clk_divider_gate to imply it's clk_hw based
clk: imx: Rename the imx_clk_pfdv2 to imply it's clk_hw based
clk: imx: Rename the imx_clk_pllv4 to imply it's clk_hw based
clk: imx: Rename sccg and frac pll register to suggest clk_hw
clk: imx: imx7ulp composite: Rename to show is clk_hw based
clk: imx: pllv2: Switch to clk_hw based API
clk: imx: pllv1: Switch to clk_hw based API
...
* clk-ti:
clk: ti: clkctrl: Fix hidden dependency to node name
clk: ti: add clkctrl data dra7 sgx
clk: ti: omap5: Add missing AESS clock
clk: ti: dra7: fix parent for gmac_clkctrl
clk: ti: dra7: add vpe clkctrl data
clk: ti: dra7: add cam clkctrl data
dt-bindings: clock: Move ti-dra7-atl.h to dt-bindings/clock
* clk-xilinx:
clk: zynqmp: Add support for clock with CLK_DIVIDER_POWER_OF_TWO flag
clk: zynqmp: Fix divider calculation
clk: zynqmp: Add support for get max divider
clk: zynqmp: Warn user if clock user are more than allowed
clk: zynqmp: Extend driver for versal
dt-bindings: clock: Add bindings for versal clock driver
* clk-nvidia:
clk: tegra20/30: Explicitly set parent clock for Video Decoder
clk: tegra20/30: Don't pre-initialize displays parent clock
clk: tegra: divider: Check UART's divider enable-bit state on rate's recalculation
clk: tegra: clk-dfll: Remove call to pm_runtime_irq_safe()
clk: tegra: Mark fuse clock as critical
* clk-qcom: (35 commits)
clk: qcom: rpmh: Sort OF match table
dt-bindings: fix warnings in validation of qcom,gcc.yaml
dt-binding: fix compilation error of the example in qcom,gcc.yaml
clk: qcom: Add ipq6018 Global Clock Controller support
clk: qcom: Add DT bindings for ipq6018 gcc clock controller
clk: qcom: gcc-msm8996: Fix parent for CLKREF clocks
clk: qcom: rpmh: Add IPA clock for SC7180
clk: qcom: rpmh: skip undefined clocks when registering
clk: qcom: Add video clock controller driver for SC7180
dt-bindings: clock: Introduce SC7180 QCOM Video clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM VIDEOCC clock bindings
clk: qcom: Add graphics clock controller driver for SC7180
dt-bindings: clock: Introduce SC7180 QCOM Graphics clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM GPUCC clock bindings
clk: qcom: apcs-msm8916: use clk_parent_data to specify the parent
clk: qcom: Add display clock controller driver for SC7180
dt-bindings: clock: Introduce QCOM sc7180 display clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM DISPCC clock bindings
clk: qcom: clk-alpha-pll: Add support for Fabia PLL calibration
clk: qcom: alpha-pll: Remove useless read from set rate
...
* clk-freescale:
clk: fsl-sai: new driver
dt-bindings: clock: document the fsl-sai driver
clk: composite: add _register_composite_pdata() variants
* clk-qoriq:
clk: qoriq: add ls1088a hwaccel clocks support
clk: ls1028a: Add clock driver for Display output interface
dt/bindings: clk: Add YAML schemas for LS1028A Display Clock bindings
The VDE parent won't be changed automatically to PLLC if bootloader
didn't do that for us, hence let's explicitly set the parent for
consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Both Tegra20 and Tegra30 are initializing display's parent clock
incorrectly because PLLP is running at 216/408MHz while display rate is
set to 600MHz, but pre-setting the parent isn't needed at all because
display driver selects proper parent anyways.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
UART clock is divided using divisor values from DLM/DLL registers when
enable-bit is unset in clk register and clk's divider configuration isn't
taken onto account in this case. This doesn't cause any problems, but
let's add a check for the divider's enable-bit state, for consistency.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
pm_runtime_irq_safe() is not needed as interrupts are allowed during
suspend and resume. This was added mistakenly during DFLL suspend and
resume support patch.
While at it, also update the description of the dev argument that is
passed to the tegra_dfll_suspend() function.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For a little over a year, U-Boot on Tegra124 has configured the flow
controller to perform automatic RAM re-repair on off->on power
transitions of the CPU rail[1]. This is mandatory for correct operation
of Tegra124. However, RAM re-repair relies on certain clocks, which the
kernel must enable and leave running. The fuse clock is one of those
clocks. Mark this clock as critical so that LP1 power mode (system
suspend) operates correctly.
[1] 3cc7942a4ae5 ARM: tegra: implement RAM repair
Reported-by: Jonathan Hunter <jonathanh@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
It's unlikely to happen in practice ever, but makes static checkers happy.
Fixes: 535f296d47 ("clk: tegra: Add suspend and resume support on Tegra210")
Reported-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lkml.kernel.org/r/20191210020512.6088-1-digetx@gmail.com
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
match_string() returns the array index of a matching string.
Use it instead of the open-coded implementation.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lkml.kernel.org/r/20191109034226.21044-1-yuehaibing@huawei.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
If CONFIG_PM_SLEEP is n, build fails:
drivers/clk/tegra/clk-tegra210.c:3426:13: error:
tegra210_clk_suspend undeclared here (not in a function); did you mean tegra_clk_ndspeed?
.suspend = tegra210_clk_suspend,
^~~~~~~~~~~~~~~~~~~~
tegra_clk_ndspeed
drivers/clk/tegra/clk-tegra210.c:3427:12: error:
tegra210_clk_resume undeclared here (not in a function); did you mean tegra210_clk_suspend?
.resume = tegra210_clk_resume,
Use ifdef to guard this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 27d10d548c04 ("clk: tegra: Add suspend and resume support on Tegra210")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There is no need to re-configure PLLX if its configuration in unchanged
on return from suspend / cpuidle, this saves 300us if PLLX is already
enabled (common case for cpuidle).
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
All the CAR controller settings are lost on suspend when core power goes
off. This implement saving and restoring context for all PLLs and clocks
during system suspend and resume to have the clocks back to same state
for normal operation.
Clock driver suspend and resume are registered as syscore_ops as clocks
restore need to happen before the other drivers resume to have all their
clocks back to the same state as before suspend.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Move CLK_OUT_ENB and RST_DEVICES registers to clk.h to share these with
Tegra clock driver.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch uses fence_udelay rather than udelay during PLLU
initialization to ensure writes to clock registers happens before
waiting for specified delay.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch implements DFLL suspend and resume operation.
During system suspend entry, CPU clock will switch CPU to safe
clock source of PLLP and disables DFLL clock output.
DFLL driver suspend confirms DFLL disable state and errors out on
being active.
DFLL is re-initialized during the DFLL driver resume as it goes
through complete reset during suspend entry.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch implements restore_context for clk_super_mux and clk_super.
During system supend, core power goes off the and context of Tegra
CAR registers is lost.
So on system resume, context of super clock registers are restored
to have them in same state as before suspend.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch has a fix to enable PLLP branches to CPU before changing
the CPU cluster clock source to PLLP for Gen5 Super clock and
disables PLLP branches to CPU when not in use.
During system suspend entry and exit, CPU source will be switched
to PLLP and this needs PLLP branches to be enabled to CPU prior to
the switch.
On system resume, warmboot code enables PLLP branches to CPU and
powers up the CPU with PLLP clock source.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch implements restore_context support for clk-periph and
clk-sdmmc-mux clock operations to restore clock parent and rates
on system resume.
During system suspend, core power goes off and looses the context
of the Tegra clock controller registers.
So on system resume, clocks parent and rate are restored back to
the context before suspend based on cached data.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch adds support for saving OSC clock frequency and the
drive-strength during OSC clock init and creates an API to restore
OSC control register value from the saved context.
This API is invoked by Tegra210 clock driver during system resume
to restore the OSC clock settings.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch implements save and restore of PLL context.
During system suspend, core power goes off and looses the settings
of the Tegra CAR controller registers.
So during resume, pll context is restored based on cached rate
and state.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch implements save and restore of pllout context.
During system suspend, core power goes off and looses the settings
of the Tegra CAR controller registers.
So during suspend entry the state of pllout is saved and on resume
it is restored back to have pllout in same state as before suspend.
pllout rate is saved and restore in clock divider so it will be at
same rate as before suspend when pllout state is restored.
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch implements context restore for clock divider.
During system suspend, core power goes off and looses the settings
of the Tegra CAR controller registers.
So on resume, clock dividers are restored back for normal operation.
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to allow the display driver to deal uniformly with all SOR
generations, implement the SOR clocks in a way that is compatible with
Tegra186 and later.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In order to allow the display driver to deal uniformly with all SOR
generations, implement the SOR clocks in a way that is compatible with
Tegra186 and later.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This makes Tegra124 and Tegra210 consistent with subsequent Tegra
generations.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The SOR0 clock on Tegra210 is very different from the SOR0 clock found
on Tegra124. Move the Tegra124 implementation to the Tegra124 driver so
that a custom implementation can be provided on Tegra210 without
clashing with the existing clock.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Later SoC generations implement this clock as SOR1_OUT. For consistency,
the Tegra210 implementation was adapted to match the same name in commit
4d1dc40185 ("dt-bindings: clock: tegra: Add sor1_out clock").
Clean up the remaining pieces by adopting the new name for the internal
identifiers and remove the old alias. Note that since both SOR1_SRC and
SOR1_OUT were referring to the same device tree clock ID, this does not
break device tree ABI.
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
A proper External Memory Controller clock rounding and parent selection
functionality is required by the EMC drivers, it is not available using
the generic clock implementation because only the Memory Controller driver
is aware of what clock rates are actually available for a particular
device. EMC drivers will have to register a Tegra-specific CLK-API
callback which will perform rounding of a requested rate. EMC clock users
won't be able to request EMC clock by getting -EPROBE_DEFER until EMC
driver is probed and the callback is set up.
The functionality is somewhat similar to the clk-emc.c which serves
Tegra124+ SoCs. The later HW generations support more parent clock sources
and the HW configuration / integration with the EMC drivers differs a tad
from the older gens, hence it's not really worth to try to squash
everything into a single source file.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
side. The two main highlights in the core framework are the addition of an bulk
clk_get API that handles optional clks and an extra debugfs file that tells the
developer about the current parent of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is mostly
because that SoC has started converting to the clk_hw style of clk
registration. The next big update is in the Amlogic meson clk driver that
gained some support for audio, cpu, and temperature clks while fixing some PLL
issues. Finally, the biggest thing that stands out is the conversion of a large
part of the Allwinner sunxi-ng driver to the new clk parent scheme that uses
less strings and more pointer comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks here and
there to clk data along with the normal addition of a handful of new drivers
and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1
-----BEGIN PGP SIGNATURE-----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=mK0C
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round of clk driver and framework updates is heavy on the driver
update side. The two main highlights in the core framework are the
addition of an bulk clk_get API that handles optional clks and an
extra debugfs file that tells the developer about the current parent
of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is
mostly because that SoC has started converting to the clk_hw style of
clk registration. The next big update is in the Amlogic meson clk
driver that gained some support for audio, cpu, and temperature clks
while fixing some PLL issues. Finally, the biggest thing that stands
out is the conversion of a large part of the Allwinner sunxi-ng driver
to the new clk parent scheme that uses less strings and more pointer
comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks
here and there to clk data along with the normal addition of a handful
of new drivers and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (190 commits)
clk: consoldiate the __clk_get_hw() declarations
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: lochnagar: Update DT binding doc to include the primary SPDIF MCLK
clk: Add Si5341/Si5340 driver
dt-bindings: clock: Add silabs,si5341
clk: clk-si544: Implement small frequency change support
clk: add BCM63XX gated clock controller driver
devicetree: document the BCM63XX gated clock bindings
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: rockchip: export HDMIPHY clock on rk3228
clk: rockchip: add watchdog pclk on rk3328
clk: rockchip: add clock id for hdmi_phy special clock on rk3228
clk: rockchip: add clock id for watchdog pclk on rk3328
clk: at91: sckc: add support for SAM9X60
...
- Do a DT/firmware lookup in clk_core_get() even when the DT index is a
nonsensical value
- Fix some clk data typos in the Amlogic DT headers/code
- Avoid returning junk in the TI clk driver when an invalid clk is
looked for
- Fix dividers for the emac clks on Stratix10 SoCs
- Fix default HDA rates on Tegra210 to correct distorted audio
-----BEGIN PGP SIGNATURE-----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=3QYB
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A handful of clk driver fixes and one core framework fix
- Do a DT/firmware lookup in clk_core_get() even when the DT index is
a nonsensical value
- Fix some clk data typos in the Amlogic DT headers/code
- Avoid returning junk in the TI clk driver when an invalid clk is
looked for
- Fix dividers for the emac clks on Stratix10 SoCs
- Fix default HDA rates on Tegra210 to correct distorted audio"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: socfpga: stratix10: fix divider entry for the emac clocks
clk: Do a DT parent lookup even when index < 0
clk: tegra210: Fix default rates for HDA clocks
clk: ti: clkctrl: Fix returning uninitialized data
clk: meson: meson8b: fix a typo in the VPU parent names array variable
clk: meson: fix MPLL 50M binding id typo
It turns out that this PLL is not used on Tegra210, so there's no need
to enable it via the init table. Remove the init table entry for this
PLL to avoid it getting enabled at boot time. If the bootloader enabled
it and forgot to turn it off, the common clock framework will now know
to disable it because it is unused.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
A PLL in IDDQ doesn't work, whether it's enabled or not. This is not a
configuration that makes sense, so warn about it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There is no need to warn if the reference PLL is enabled with the
correct defaults. Only warn if the boot values don't match the defaults.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Full-speed and low-speed USB devices do not work with Tegra210
platforms because of incorrect PLLU/PLLU_OUT1 clock settings.
When full-speed device is connected:
[ 14.059886] usb 1-3: new full-speed USB device number 2 using tegra-xusb
[ 14.196295] usb 1-3: device descriptor read/64, error -71
[ 14.436311] usb 1-3: device descriptor read/64, error -71
[ 14.675749] usb 1-3: new full-speed USB device number 3 using tegra-xusb
[ 14.812335] usb 1-3: device descriptor read/64, error -71
[ 15.052316] usb 1-3: device descriptor read/64, error -71
[ 15.164799] usb usb1-port3: attempt power cycle
When low-speed device is connected:
[ 37.610949] usb usb1-port3: Cannot enable. Maybe the USB cable is bad?
[ 38.557376] usb usb1-port3: Cannot enable. Maybe the USB cable is bad?
[ 38.564977] usb usb1-port3: attempt power cycle
This commit fixes the issue by:
1. initializing PLLU_OUT1 before initializing XUSB_FS_SRC clock
because PLLU_OUT1 is parent of XUSB_FS_SRC.
2. changing PLLU post-divider to /2 (DIVP=1) according to Technical
Reference Manual.
Fixes: e745f992cf ("clk: tegra: Rework pll_u")
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the default clock rates for the HDA and HDA2CODEC_2X clocks
are both 19.2MHz. However, the default rates for these clocks should
actually be 51MHz and 48MHz, respectively. The current clock settings
results in a distorted output during audio playback. Correct the default
clock rates for these clocks by specifying them in the clock init table
for Tegra210.
Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Memory Controller (MC) clock rate can't be simply changed and nothing
in kernel need to change the rate, hence let's make the clock read-only.
This id also needed for the EMC driver because timing configuration may
require the MC clock diver to be disabled, that is handled by the EMC
clock / EMC driver integration and CLK framework shall not touch the
MC divider configuration on the EMC clock rate change.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When a clk user requests rate that is higher than the maximum possible,
the rate shall be clamped to the maximum and not to the current value.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The timings parser doesn't append timings, but instead it parses only
the first timing and hence doesn't store all of the timings when
device-tree has timings for multiple RAM codes. In a result EMC scaling
doesn't work if timings are missing.
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The EMC clock marked as critical, hence it is already enabled at the
registration time.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According to the Tegra124 TRM documentation, PLLM_MISC2 register doesn't
have the lock-enable bit as well as any other PLLM-related register. Hence
PLLM re-locking can't be initiated by software. The incorrect bit setting
should have been harmless since that bit is undefined according to TRM.
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
There are wrongly set parenthesis in the code that are resulting in a
wrong configuration being programmed for PLLM. The original fix was made
by Danny Huang in the downstream kernel. The patch was tested on Nyan Big
Tegra124 chromebook, PLLM rate changing works correctly now and system
doesn't lock up after changing the PLLM rate due to EMC scaling.
Cc: <stable@vger.kernel.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Now that clk_{readl,writel} is just an alias for {readl,writel}, we can
switch all users of clk_* to use the accessors directly and remove the
helpers.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
[sboyd@kernel.org: Also convert renesas file so that this can be
compile independently]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Initially Common Clock Framework isn't aware of the clock-enable status,
this results in enabling of clocks that were enabled by bootloader. This
is not a big deal for a regular clock-gates, but for PLL's it may have
some unpleasant consequences. Thus re-enabling PLLX (the main CPU parent
clock) may result in extra long period of PLL re-locking.
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fix sparse warning:
drivers/clk/tegra/clk-super.c:124:22:
warning: symbol 'tegra_clk_super_mux_ops' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
updates this time around. It's the usual pile of new drivers for new
hardware out there and the normal small fixes and updates, but then we
have some core framework changes too.
In the core framework, we introduce support for a clk_get_optional() API
to get clks that may not always be populated and a way to devm manage clkdev
lookups registered by provider drivers. We also do some refactoring to simplify
the interface between clkdev and the common clk framework so we can reuse the DT
parsing and clk_get() path in provider drivers in the future. This work will
continue in the next few cycles while we convert how providers specify clk
parents.
On the driver side, the biggest part of the dirstat is the Amlogic clk driver
that got support for the G12A SoC. It dominates with almost half the overall
diff, while the second largest part of the diff is in the i.MX clk driver
that gained support for imx8mm SoCs. After that, we have the Actions Semiconductor
and Qualcomm drivers rounding out the big part of the dirstat because they both
got new hardware support for SoCs. The rest is just various updates and non-critical
fixes for existing drivers.
Core:
- Convert a few clk bindings to JSON schema format
- Add a {devm_}clk_get_optional() API
- Add devm_clk_hw_register_clkdev() API to manage clkdev lookups
- Start rewriting clk parent registration and supporting device links
by moving around code that supports clk_get() and DT parsing of the
'clocks' property
New Drivers:
- Add Qualcomm MSM8998 RPM managed clks
- IPA clk support on Qualcomm RPMh clk controllers
- Actions Semi S500 SoC clk support
- Support for fixed rate clks populated from an MMIO register
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car V3H
- Add TMU (timer) clocks on Renesas RZ/G2E
- Add Amlogic G12A Always-On Clock Controller
- Add 32k clock generation for Amlogic AXG
- Add support for the Mali GPU clocks on Amlogic Meson8
- Add Amlogic G12A EE clock controller driver
- Add missing CANFD clocks on Renesas RZ/G2M and RZ/G2E
- Add i.MX8MM SoC clk driver support
Removed Drivers:
- Remove clps711x driver as the board support is gone
Updates:
- 3rd ECO fix for Mediatek MT2712 SoCs
- Updates for Qualcomm MSM8998 GCC clks
- Random static analysis fixes for clk drivers
- Support for sleeping gpios in the clk-gpio type
- Minor fixes for STM32MP1 clk driver (parents, critical flag, etc.)
- Split LCDC into two clks on the Marvell MMP2 SoC
- Various DT of_node refcount fixes
- Get rid of CLK_IS_BASIC from TI code (yay!)
- TI Autoidle clk support
- Fix Amlogic Meson8 APB clock ID name
- Claim input clocks through DT for Amlogic AXG and GXBB
- Correct the DU (display unit) parent clock on Renesas RZ/G2E
- Exynos5433 IMEM CMU crypto clk support (SlimSS)
- Fix for the PLL-MIPI on the Allwinner A23
- Fix Rockchip rk3328 PLL rate calculation
- Add SET_RATE_PARENT flag on display clk of Rockhip rk3066
- i.MX SCU clk driver clk_set_parent() and cpufreq support
-----BEGIN PGP SIGNATURE-----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=D4Bv
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk subsystem updates from Stephen Boyd:
"We have a fairly balanced mix of clk driver updates and clk framework
updates this time around. It's the usual pile of new drivers for new
hardware out there and the normal small fixes and updates, but then we
have some core framework changes too.
In the core framework, we introduce support for a clk_get_optional()
API to get clks that may not always be populated and a way to devm
manage clkdev lookups registered by provider drivers. We also do some
refactoring to simplify the interface between clkdev and the common
clk framework so we can reuse the DT parsing and clk_get() path in
provider drivers in the future. This work will continue in the next
few cycles while we convert how providers specify clk parents.
On the driver side, the biggest part of the dirstat is the Amlogic clk
driver that got support for the G12A SoC. It dominates with almost
half the overall diff, while the second largest part of the diff is in
the i.MX clk driver that gained support for imx8mm SoCs. After that,
we have the Actions Semiconductor and Qualcomm drivers rounding out
the big part of the dirstat because they both got new hardware support
for SoCs. The rest is just various updates and non-critical fixes for
existing drivers.
Core:
- Convert a few clk bindings to JSON schema format
- Add a {devm_}clk_get_optional() API
- Add devm_clk_hw_register_clkdev() API to manage clkdev lookups
- Start rewriting clk parent registration and supporting device links
by moving around code that supports clk_get() and DT parsing of the
'clocks' property
New Drivers:
- Add Qualcomm MSM8998 RPM managed clks
- IPA clk support on Qualcomm RPMh clk controllers
- Actions Semi S500 SoC clk support
- Support for fixed rate clks populated from an MMIO register
- Add RPC (QSPI/HyperFLASH) clocks on Renesas R-Car V3H
- Add TMU (timer) clocks on Renesas RZ/G2E
- Add Amlogic G12A Always-On Clock Controller
- Add 32k clock generation for Amlogic AXG
- Add support for the Mali GPU clocks on Amlogic Meson8
- Add Amlogic G12A EE clock controller driver
- Add missing CANFD clocks on Renesas RZ/G2M and RZ/G2E
- Add i.MX8MM SoC clk driver support
Removed Drivers:
- Remove clps711x driver as the board support is gone
Updates:
- 3rd ECO fix for Mediatek MT2712 SoCs
- Updates for Qualcomm MSM8998 GCC clks
- Random static analysis fixes for clk drivers
- Support for sleeping gpios in the clk-gpio type
- Minor fixes for STM32MP1 clk driver (parents, critical flag, etc.)
- Split LCDC into two clks on the Marvell MMP2 SoC
- Various DT of_node refcount fixes
- Get rid of CLK_IS_BASIC from TI code (yay!)
- TI Autoidle clk support
- Fix Amlogic Meson8 APB clock ID name
- Claim input clocks through DT for Amlogic AXG and GXBB
- Correct the DU (display unit) parent clock on Renesas RZ/G2E
- Exynos5433 IMEM CMU crypto clk support (SlimSS)
- Fix for the PLL-MIPI on the Allwinner A23
- Fix Rockchip rk3328 PLL rate calculation
- Add SET_RATE_PARENT flag on display clk of Rockhip rk3066
- i.MX SCU clk driver clk_set_parent() and cpufreq support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (150 commits)
dt-bindings: clock: imx8mq: Fix numbering overlaps and gaps
clk: ti: clkctrl: Fix clkdm_name regression for TI_CLK_CLKCTRL_COMPAT
clk: fixup default index for of_clk_get_by_name()
clk: Move of_clk_*() APIs into clk.c from clkdev.c
clk: Inform the core about consumer devices
clk: Introduce of_clk_get_hw_from_clkspec()
clk: core: clarify the check for runtime PM
clk: Combine __clk_get() and __clk_create_clk()
clk: imx8mq: add GPIO clocks to clock tree
clk: mediatek: correct cpu clock name for MT8173 SoC
clk: imx: Refactor entire sccg pll clk
clk: imx: scu: add cpu frequency scaling support
clk: mediatek: Mark bus and DRAM related clocks as critical
clk: mediatek: Add flags to mtk_gate
clk: mediatek: Add MUX_FLAGS macro
clk: qcom: gcc-sdm845: Define parent of PCIe PIPE clocks
clk: ingenic: Remove set but not used variable 'enable'
clk: at91: programmable: remove unneeded register read
clk: mediatek: using CLK_MUX_ROUND_CLOSEST for the clock of dpi1_sel
clk: mediatek: add MUX_GATE_FLAGS_2
...
Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.
Semantic patch information:
Rationale: DEFINE_SIMPLE_ATTRIBUTE + debugfs_create_file()
imposes some significant overhead as compared to
DEFINE_DEBUGFS_ATTRIBUTE + debugfs_create_file_unsafe().
Generated by: scripts/coccinelle/api/debugfs/debugfs_simple_attr.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following sparse warning:
drivers/clk/tegra/clk-tegra124-dfll-fcpu.c:244:18: warning:
symbol 'tegra210_cpu_cvb_tables' was not declared. Should it be static?
Fixes: 2b2dbc2f94 ("clk: tegra: dfll: add CVB tables for Tegra210")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This contains a couple of prerequisite patches to enable CPU frequency
scaling on Tegra210.
-----BEGIN PGP SIGNATURE-----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=R+Ez
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.1-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
clk: tegra: Changes for v5.1-rc1
This contains a couple of prerequisite patches to enable CPU frequency
scaling on Tegra210.
* tag 'tegra-for-5.1-clk' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
clk: tegra: dfll: build clk-dfll.c for Tegra124 and Tegra210
clk: tegra: dfll: add CVB tables for Tegra210
clk: tegra: dfll: round down voltages based on alignment
clk: tegra: dfll: support PWM regulator control
clk: tegra: dfll: CVB calculation alignment with the regulator
clk: tegra: dfll: registration for multiple SoCs
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tegra210 has a DFLL as well and can share the majority of the code with
the Tegra124 implementation. So build the same code for both platforms.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add CVB tables with different chip characterization, so that we can
generate the customize OPP table that suitable for different chips with
different SKUs.
The parameter 'tune_high_min_millivolts' is first time introduced in
this patch, which didn't use in the DFLL driver for clock and voltage
tuning before. It will be used later when DFLL in high voltage range.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When generating the OPP table, the voltages are round down with the
alignment from the regulator. The alignment should be applied for
voltages look up as well.
Based on the work of Penny Chiu <pchiu@nvidia.com>.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DFLL hardware supports two modes (I2C and PWM) for voltage control
when requesting a frequency. In this patch, we introduce PWM mode support.
To support that, we re-organize the LUT for unifying the table for both
cases of I2C and PWM mode. And generate that based on regulator info.
For the PWM-based regulator, we get this info from DT. And do the same as
the case of I2C LUT, which can help to map the PMIC voltage ID and voltages
that the regulator supported.
The other parts are the support code for initializing the DFLL hardware
to support PWM mode. Also, the register debugfs file is slightly
reworked to only show the i2c registers when I2C mode is in use.
Based on the work of Peter De Schrijver <pdeschrijver@nvidia.com>.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The CVB table contains calibration data for the CPU DFLL based on
process characterization. The regulator step and offset parameters depend
on the regulator supplying vdd-cpu, not on the specific Tegra SKU.
When using a PWM controlled regulator, the voltage step and offset are
determined by the regulator type in use. This is specified in DT. When
using an I2C controlled regulator, we can retrieve them from CPU regulator
Then pass this information to the CVB table calculation function.
Based on the work done of "Peter De Schrijver <pdeschrijver@nvidia.com>"
and "Alex Frid <afrid@nvidia.com>".
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In a future patch, support for the DFLL in Tegra210 will be introduced.
This requires support for more than 1 set of CVB and CPU max frequency
tables.
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
If tegra_dfll_unregister() fails then "soc" is an error pointer. We
should just return instead of dereferencing it.
Fixes: 1752c9ee23 ("clk: tegra: dfll: Fix drvdata overwriting issue")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk-renesas:
clk: renesas: rcar-gen3: Add HS400 quirk for SD clock
clk: renesas: rcar-gen3: Add documentation for SD clocks
clk: renesas: rcar-gen3: Set state when registering SD clocks
clk: renesas: r8a77995: Simplify PLL3 multiplier/divider
clk: renesas: r8a77995: Add missing CPEX clock
clk: renesas: r8a77995: Remove non-existent SSP clocks
clk: renesas: r8a77995: Remove non-existent VIN5-7 module clocks
clk: renesas: r8a77995: Correct parent clock of DU
clk: renesas: r8a77990: Correct parent clock of DU
clk: renesas: r8a77970: Add CPEX clock
clk: renesas: r8a77965: Add CPEX clock
clk: renesas: r8a7796: Add CPEX clock
clk: renesas: r8a7795: Add CPEX clock
clk: renesas: r8a774a1: Add CPEX clock
dt-bindings: clock: r8a7796: Remove CSIREF clock
dt-bindings: clock: r8a7795: Remove CSIREF clock
clk: renesas: Mark rza2_cpg_clk_register static
clk: renesas: r7s9210: Add USB clocks
clk: renesas: r8a77970: Add RPC clocks
clk: renesas: r7s9210: Add SDHI clocks
* clk-allwinner:
clk: sunxi-ng: a64: Allow parent change for VE clock
clk: sunxi-ng: a33: Set CLK_SET_RATE_PARENT for all audio module clocks
clk: sunxi-ng: a33: Use sigma-delta modulation for audio PLL
clk: sunxi-ng: h3: Allow parent change for ve clock
clk: sunxi-ng: add support for suniv F1C100s SoC
dt-bindings: clock: Add Allwinner suniv F1C100s CCU
clk: sunxi-ng: h3/h5: Fix CSI_MCLK parent
clk: sunxi-ng: r40: Force LOSC parent to RTC LOSC output
clk: sunxi-ng: sun50i: a64: Use sigma-delta modulation for audio PLL
clk: sunxi-ng: a64: Fix gate bit of DSI DPHY
clk: sunxi-ng: Enable DE2_CCU for SUN8I and SUN50I
clk: sunxi-ng: Add support for H6 DE3 clocks
dt-bindings: clock: sun8i-de2: Add H6 DE3 clock description
clk: sunxi-ng: h6: Set video PLLs limits
clk: sunxi-ng: Use u64 for calculation of NM rate
clk: sunxi-ng: Adjust MP clock parent rate when allowed
clk: sunxi-ng: sun50i: h6: Fix MMC clock mux width
clk: sunxi-ng: enable so-said LDOs for A64 SoC's pll-mipi clock
* clk-tegra:
clk: tegra: Return the exact clock rate from clk_round_rate
clk: tegra30: Use Tegra CPU powergate helper function
soc/tegra: pmc: Drop SMP dependency from CPU APIs
clk: tegra: Fix maximum audio sync clock for Tegra124/210
clk: tegra: get rid of duplicate defines
clk: tegra20: Check whether direct PLLM sourcing is turned off for EMC
clk: tegra20: Turn EMC clock gate into divider
* clk-meson: (25 commits)
clk: meson: axg-audio: use the clk input helper function
clk: meson: add clk-input helper function
clk: meson: Mark some things static
clk: meson: meson8b: add the read-only video clock trees
clk: meson: meson8b: add the fractional divider for vid_pll_dco
clk: meson: meson8b: fix the offset of vid_pll_dco's N value
clk: meson: Fix GXL HDMI PLL fractional bits width
clk: meson: meson8b: add the CPU clock post divider clocks
clk: meson: meson8b: rename cpu_div2/cpu_div3 to cpu_in_div2/cpu_in_div3
clk: meson: clk-regmap: add read-only gate ops
clk: meson: meson8b: allow changing the CPU clock tree
clk: meson: meson8b: run from the XTAL when changing the CPU frequency
clk: meson: meson8b: add support for more M/N values in sys_pll
clk: meson: meson8b: mark the CPU clock as CLK_IS_CRITICAL
clk: meson: meson8b: do not use cpu_div3 for cpu_scale_out_sel
clk: meson: clk-pll: check if the clock is already enabled
clk: meson: meson8b: fix the width of the cpu_scale_div clock
clk: meson: meson8b: fix incorrect divider mapping in cpu_scale_table
clk: meson: meson8b: use the HHI syscon if available
dt-bindings: clock: meson8b: use the registers from the HHI syscon
...
* clk-rockchip:
clk: rockchip: add clock-id to gate of ACODEC for rk3328
clk: rockchip: add clock ID of ACODEC for rk3328
clk: rockchip: fix ID of 8ch clock of I2S1 for rk3328
clk: rockchip: fix I2S1 clock gate register for rk3328
clk: rockchip: make rk3188 hclk_vio_bus critical
clk: rockchip: fix rk3188 sclk_mac_lbtest parameter ordering
clk: rockchip: fix rk3188 sclk_smc gate data
clk: rockchip: fix typo in rk3188 spdif_frac parent
The current behavior is that clk_round_rate would return the same clock
rate passed to it for valid PLL configurations. This change will return
the exact rate the PLL will provide in accordance with clk API.
Signed-off-by: Robert Yang <decatf@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Rather than using the tegra_powergate_is_powered() function for
determining if a CPU is powered, use the tegra_pmc_cpu_is_powered()
instead which was created to get the CPU power status. Internally
tegra_pmc_cpu_is_powered() calls tegra_powergate_is_powered() and so
is equivalent.
The Tegra30 clock driver is the only public user of
tegra_powergate_is_powered() and so by updating the Tegra30 clock
driver to use tegra_pmc_cpu_is_powered(), we can then make
tegra_powergate_is_powered() a non-public function.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The maximum frequency supported for I2S on Tegra124 and Tegra210 is
24.576MHz (as stated in the Tegra TK1 data sheet for Tegra124 and the
Jetson TX1 module data sheet for Tegra210). However, the maximum I2S
frequency is limited to 24MHz because that is the maximum frequency of
the audio sync clock. Increase the maximum audio sync clock frequency
to 24.576MHz for Tegra124 and Tegra210 in order to support 24.576MHz
for I2S.
Update the tegra_clk_register_sync_source() function so that it does
not set the initial rate for the sync clocks and use the clock init
tables to set the initial rate instead.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Use macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Ensure that direct PLLM sourcing is turned off for EMC as we don't support
that configuration in the clk driver.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Kernel should never gate the EMC clock as it causes immediate lockup, so
removing clk-gate functionality doesn't affect anything. Turning EMC clk
gate into divider allows to implement glitch-less EMC scaling, avoiding
reparenting to a backup clock.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
You can't compile this file by itself because it uses SZ_64K from
sizes.h but doesn't include it. Instead it relies on some certain
configuration pulling that in implicitly somewhere else. Just add the
include to make random compile testing easier.
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fix some incorrect data in LVL2 offset and bit mask.
Fixes: e403d00573 ("clk: tegra: MBIST work around for Tegra210")
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Actually report the error code from devm_regulator_get() which may as
well just be a probe deferral.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* clk-imx-critical:
: - Convert to CLK_IS_CRITICAL for i.MX51/53 driver
clk: imx51-imx53: Include sizes.h to silence compile errors
clk: imx51-imx53: Annotate critical clocks as CLK_IS_CRITICAL
* clk-tegra-bpmp:
: - Fix Tegra BPMP driver oops when some xlating a NULL clk
clk: tegra: bpmp: Don't crash when a clock fails to register
* clk-tegra-124:
: - Proper default configuration for vic03 and vde clks on Tegra124
clk: tegra: Make vde a child of pll_c3
clk: tegra: Make vic03 a child of pll_c3
* clk-tegra-critical:
: - Mark Tegra memory controller clks as critical
clk: tegra: Mark Memory Controller clock as critical
* clk-tegra-emc-oob:
: - Fix array bounds clamp in Tegra's emc determine_rate() op
clk: tegra: emc: Avoid out-of-bounds bug
These clocks have low jitter paths to certain parents. To model these
correctly, use the sdmmc mux divider clock type.
Signed-off-by: Peter De-Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a clock type to model the sdmmc switch divider clocks which have paths
to source clocks bypassing the divider (Low Jitter paths). These
are handled by selecting the lj path when the divider is 1 (ie the
rate is the parent rate), otherwise the normal path with divider
will be selected. Otherwise this clock behaves as a normal peripheral
clock.
Signed-off-by: Peter De-Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Move this to a separate file so it can be used to calculate the sdmmc
clock dividers.
Signed-off-by: Peter De-Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add the missing linux/delay.h include statement for udelay() used by
fence_udelay() macro.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
Acked-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Apparently there was an attempt to avoid out-of-bounds accesses when there
is only one memory timing available, but there is a typo in the code that
neglects that attempt.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Sowjanya Komatineni