The DRM bus flags convey additional information on pixel data on
the bus. All current available bus flags might be of interest for
a bridge. Remove the sampling_edge field and use bus_flags.
In the case at hand a dumb VGA bridge needs a specific data enable
polarity (DRM_BUS_FLAG_DE_LOW).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DRM_BUS_FLAG_PIXDATA_(POS|NEG)EDGE and
DRM_BUS_FLAG_SYNC_(POS|NEG)EDGE flags are deprecated in favour of the
new DRM_BUS_FLAG_PIXDATA_(DRIVE|SAMPLE)_(POS|NEG)EDGE and
new DRM_BUS_FLAG_SYNC_(DRIVE|SAMPLE)_(POS|NEG)EDGE flags. Replace them
through the code.
This effectively changes the value of the .sampling_edge bridge timings
field in the dumb-vga-dac driver. This is safe to do as no driver
consumes these values yet.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The mode and ajusted_mode passed to the bridge .mode_set() operation
should never be modified by the bridge (and are not in any of the
existing bridge drivers). Make them const to make this clear.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After some discussion and failed patch sets trying to convey
the right timing information between the display engine and
a bridge using the connector, I try instead to use an optional
timing information container in the bridge itself, so that
display engines can retrieve it from any bridge and use it to
determine how to drive outputs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180112074854.9560-2-linus.walleij@linaro.org
This will let drivers reduce the error cleanup they need, in
particular the "is_panel_bridge" flag.
v2: Slight cleanup of remove function by Andrzej
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170718210510.12229-2-eric@anholt.net
Many DRM drivers have common code to make a stub connector
implementation that wraps a drm_panel. By wrapping the panel in a DRM
bridge, all of the connector code (including calls during encoder
enable/disable) goes away.
v2: Fix build with CONFIG_DRM=m, drop "dev" argument that should just
be the panel's dev, move kerneldoc up a level and document
_remove().
v3: Fix another breakage with CONFIG_DRM=m, fix breakage with
CONFIG_OF=n, move protos under CONFIG_DRM_PANEL_BRIDGE, wrap a
line.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> (v2)
Acked-by: Archit Taneja <architt@codeaurora.org> (v2)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170602202514.11900-1-eric@anholt.net
Introduce a new helper function which calls mode_valid() callback
for all bridges in an encoder chain.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/36bd5e054496ad3c9c71f1ffe204f28533f55f1e.1495720737.git.joabreu@synopsys.com
Laurent started a massive discussion on IRC about this. Let's try to
document common usage a bit better.
v2: Cross-links+typos.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170515091136.26307-1-daniel.vetter@ffwll.ch
This adds a new callback to crtc, encoder and bridge helper functions
called mode_valid(). This callback shall be implemented if the
corresponding component has some sort of restriction in the modes
that can be displayed. A NULL callback implicates that the component
can display all the modes.
We also change the documentation so that the new and old callbacks
are correctly documented.
Only the callbacks were implemented to simplify review process,
following patches will make use of them.
Changes in v2 from Daniel:
- Update the warning about how modes aren't filtered in atomic_check -
the heleprs help out a lot more now.
- Consistenly roll out that warning, crtc/encoder's atomic_check
missed it.
- Sprinkle more links all over the place, so it's easier to see where
this stuff is used and how the differen hooks are related.
- Note that ->mode_valid is optional everywhere.
- Explain why the connector's mode_valid is special and does _not_ get
called in atomic_check.
v3: Document what can and cannot be checked in mode_valid a bit better
(Andrjez). Answer: Only allowed to look at the mode, nothing else.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v2)
Reviewed-by: Jose Abreu <joabreu@synopsys.com> (v2)
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170515093347.31098-1-daniel.vetter@ffwll.ch
I just learned that &struct_name.member_name works and looks pretty
even. It doesn't (yet) link to the member directly though, which would
be really good for big structures or vfunc tables (where the
per-member kerneldoc tends to be long).
Also some minor drive-by polish where it makes sense, I read a lot
of docs ...
Cc: Archit Taneja <architt@codeaurora.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
[danvet: Remove spurious hunk that Archit spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1483044517-5770-13-git-send-email-daniel.vetter@ffwll.ch
sed -e 's/\( \* .*\)struct &\([_a-z]*\)/\1\&struct \2/' -i
Originally I wasnt a friend of this style because I thought a
line-break between the "&struct" and "foo" part would break it. But a
quick test shows that " * &struct \n * foo\n" works pefectly well with
current kernel-doc. So time to mass-apply these changes!
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1483044517-5770-6-git-send-email-daniel.vetter@ffwll.ch
Instead of linking encoders and bridges in every driver (and getting it
wrong half of the time, as many drivers forget to set the drm_bridge
encoder pointer), do so in core code. The drm_bridge_attach() function
needs the encoder and optional previous bridge to perform that task,
update all the callers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Stefan Agner <stefan@agner.ch> # For DCU
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> # For atmel-hlcdc
Acked-by: Vincent Abriou <vincent.abriou@st.com> # For STI
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> # For sun4i
Acked-by: Xinliang Liu <z.liuxinliang@hisilicon.com> # For hisilicon
Acked-by: Jyri Sarha <jsarha@ti.com> # For tilcdc
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1481709550-29226-4-git-send-email-laurent.pinchart+renesas@ideasonboard.com
Stefan Agner