Similar to the sdvo code we poke the dvo encoder whether the output is
active. Safe that dvo encoders are not standardized, so this requires
a new callback into the dvo chip driver.
Hence implement that for all 6 dvo drivers.
v2: With the newly added ns2501 we now have 6 dvo drivers instead of
just 5 ...
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All dvo drivers only support 2 dpms states, and our dvo driver
even switches of the dvo port for anything else than DPMS_ON. Hence
ditch this complexity and simply use bool enable.
While reading through this code I've noticed that the mode_set
function of ch7017 is a bit peculiar - it disable the lvds again, even
though the crtc helper code should have done that ... This might be to
work around an issue at driver load, we pretty much ignore the hw
state when taking over.
v2: Also do the conversion for the new ns2501 driver.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Various issues involved with the space character were generating
warnings in the checkpatch.pl file. This patch removes most of those
warnings.
Signed-off-by: Akshay Joshi <me@akshayjoshi.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
As we have already detected something attached to the chip during
initialisation, always report the LVDS connector status as connected
during probing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Use the GMBUS interface rather than direct bit banging to grab the EDID
over DDC (and for other forms of auxiliary communication with external
display controllers). The hope is that this method will be much faster
and more reliable than bit banging for fetching EDIDs from buggy monitors
or through switches, though we still preserve the bit banging as a
fallback in case GMBUS fails.
Based on an original patch by Jesse Barnes.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This was brought over from UMS, and used for a while until we decided
that drm_helper_resume_force_mode was easier and more reliable, since
it didn't require duplicating all the code deleted here. We just
forgot to delete all that junk for a while.
The existing API passed around intel_i2c_chan pointers, which are dependent
on the i2c bit-banging algo. This precluded the driver from using outputs
which use a different algo. Switching to the more general i2c_adpater allows
the driver to support non bit-banging DDC.
This also required moving the slave address into the output private
structures.
Signed-off-by: Keith Packard <keithp@keithp.com>
This commit adds i915 driver support for the DRM mode setting APIs.
Currently, VGA, LVDS, SDVO DVI & VGA, TV and DVO LVDS outputs are
supported. HDMI, DisplayPort and additional SDVO output support will
follow.
Support for the mode setting code is controlled by the new 'modeset'
module option. A new config option, CONFIG_DRM_I915_KMS controls the
default behavior, and whether a PCI ID list is built into the module for
use by user level module utilities.
Note that if mode setting is enabled, user level drivers that access
display registers directly or that don't use the kernel graphics memory
manager will likely corrupt kernel graphics memory, disrupt output
configuration (possibly leading to hangs and/or blank displays), and
prevent panic/oops messages from appearing. So use caution when
enabling this code; be sure your user level code supports the new
interfaces.
A new SysRq key, 'g', provides emergency support for switching back to
the kernel's framebuffer console; which is useful for testing.
Co-authors: Dave Airlie <airlied@linux.ie>, Hong Liu <hong.liu@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel Vetter