If the "workaround_for_vbus" is true, the driver will not call
usb_disconnect(). So, since the controller keeps some registers'
value, the driver doesn't re-enumarate suitable speed after
the b-device mode is disabled. To fix the issue, this patch
adds usb_disconnect() calling in renesas_usb3_b_device_write()
if workaround_for_vbus is true.
Fixes: 43ba968b00 ("usb: gadget: udc: renesas_usb3: add debugfs to set the b-device mode")
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Automatic NUMA Balancing uses a multi-stage pass to decide whether a page
should migrate to a local node. This filter avoids excessive ping-ponging
if a page is shared or used by threads that migrate cross-node frequently.
Threads inherit both page tables and the preferred node ID from the
parent. This means that threads can trigger hinting faults earlier than
a new task which delays scanning for a number of seconds. As it can be
load balanced very early in its lifetime there can be an unnecessary delay
before it starts migrating thread-local data. This patch migrates private
pages faster early in the lifetime of a thread using the sequence counter
as an identifier of new tasks.
With this patch applied, STREAM performance is the same as 4.17 even though
processes are not spread cross-node prematurely. Other workloads showed
a mix of minor gains and losses. This is somewhat expected most workloads
are not very sensitive to the starting conditions of a process.
4.19.0-rc5 4.19.0-rc5 4.17.0
numab-v1r1 fastmigrate-v1r1 vanilla
MB/sec copy 43298.52 ( 0.00%) 47335.46 ( 9.32%) 47219.24 ( 9.06%)
MB/sec scale 30115.06 ( 0.00%) 32568.12 ( 8.15%) 32527.56 ( 8.01%)
MB/sec add 32825.12 ( 0.00%) 36078.94 ( 9.91%) 35928.02 ( 9.45%)
MB/sec triad 32549.52 ( 0.00%) 35935.94 ( 10.40%) 35969.88 ( 10.51%)
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Reviewed-by: Rik van Riel <riel@surriel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jirka Hladky <jhladky@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linux-MM <linux-mm@kvack.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20181001100525.29789-3-mgorman@techsingularity.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Rate limiting of page migrations due to automatic NUMA balancing was
introduced to mitigate the worst-case scenario of migrating at high
frequency due to false sharing or slowly ping-ponging between nodes.
Since then, a lot of effort was spent on correctly identifying these
pages and avoiding unnecessary migrations and the safety net may no longer
be required.
Jirka Hladky reported a regression in 4.17 due to a scheduler patch that
avoids spreading STREAM tasks wide prematurely. However, once the task
was properly placed, it delayed migrating the memory due to rate limiting.
Increasing the limit fixed the problem for him.
Currently, the limit is hard-coded and does not account for the real
capabilities of the hardware. Even if an estimate was attempted, it would
not properly account for the number of memory controllers and it could
not account for the amount of bandwidth used for normal accesses. Rather
than fudging, this patch simply eliminates the rate limiting.
However, Jirka reports that a STREAM configuration using multiple
processes achieved similar performance to 4.16. In local tests, this patch
improved performance of STREAM relative to the baseline but it is somewhat
machine-dependent. Most workloads show little or not performance difference
implying that there is not a heavily reliance on the throttling mechanism
and it is safe to remove.
STREAM on 2-socket machine
4.19.0-rc5 4.19.0-rc5
numab-v1r1 noratelimit-v1r1
MB/sec copy 43298.52 ( 0.00%) 44673.38 ( 3.18%)
MB/sec scale 30115.06 ( 0.00%) 31293.06 ( 3.91%)
MB/sec add 32825.12 ( 0.00%) 34883.62 ( 6.27%)
MB/sec triad 32549.52 ( 0.00%) 34906.60 ( 7.24%
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Reviewed-by: Rik van Riel <riel@surriel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jirka Hladky <jhladky@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linux-MM <linux-mm@kvack.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20181001100525.29789-2-mgorman@techsingularity.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since 890658b7ab ("locking/mutex: Kill arch specific code"), there
are no mutex header files under arch/, so we can remove the redundant
entry from MAINTAINERS.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: Jason Low <jason.low2@hpe.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20181001142856.GC9716@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
fd_install() moves the reference given to it into the file descriptor table
of the current process. If the current process is multithreaded, then
immediately after fd_install(), another thread can close() the file
descriptor and cause the file's resources to be cleaned up.
Since the reference to "lessee" is held by the file, we must not access
"lessee" after the fd_install() call.
As far as I can tell, to reach this codepath, the caller must have an open
file descriptor to a DRI device in master mode. I'm not sure what the
requirements for that are.
Signed-off-by: Jann Horn <jannh@google.com>
Fixes: 62884cd386 ("drm: Add four ioctls for managing drm mode object leases [v7]")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001153117.216923-1-jannh@google.com
Added interrupt handler for WkupAlert interrupt.
This interrupt should initiate Remote Wake up.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
WKUP_ALERT interrupt should be unmask when lpm mode is enabled.
This interrupt is asserted when the device is in L1 for the duration
mentioned in GREFCLK.SOF_CNN_WKUP_ALERT. This is used to alert SW to
initiate Remote wake up so that the device resumes in time in order not
to lose sync with the host frame number.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added dwc2_gadget_program_ref_clk function to program GREFCLK
register in device mode.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added ref_clk_per and sof_cnt_wkup_alert parameters in
dwc2_core_params struct and set default values.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
New registers were added to dwc otg core.
GREFCLK - This register used to control ref_clk parameters.
GINTSTS2 - New WKUP_ALERT interrupt was added.
GINTMSK2 - Mask register for GINTSTS2.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In service interval based scheduling target (u)frame must be
set as a last frame in this the service interval.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added dwc2_gadget_dec_frame_num_by_one() function in gadget.c.
This function will be used to calculate descriptor frame number field
value. For service interval mode frame number in descriptor should point
to last (u)frame in the interval.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added core parameter for service interval based scheduling.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added GHWCFG4_SERVICE_INTERVAL_SUPPORTED and
DCTL_SERVICE_INTERVAL_SUPPORTED bits definitions to support
service interval based scheduling.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds support for R-Car E3. This SoC needs to release
the PLL reset by the UGCTRL register like R-Car D3. So, this patch
adds a usbhs_of_match entry for this SoC with
"USBHS_TYPE_RCAR_GEN3_WITH_PLL".
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch adds bindings for r8a77990 (R-Car E3).
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since R-Car D3 can use OTG mode, this patch changes the UGCTRL2
value to UGCTRL2_USB0SEL_OTG and UGCTRL2_VBUSSEL like other R-Car
Gen3 SoCs.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This reverts commit cd14247d5c.
R-Car D3 can use OTG mode in fact. So, the commit doesn't need anymore.
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Via p_chmask/c_chmask the user can define whether uac2 shall support
playback and/or capture. This has only effect on the created ALSA device,
but not on the USB descriptor. This patch adds playback/capture descriptors
dependent on that parameter.
Signed-off-by: Andreas Pape <apape@de.adit-jv.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The gadget documentation doesn't state clearly whether a gadget
driver's ->disconnect() callback should be invoked when the D+ pullup
is turned off. Some UDC drivers do this and some don't. This patch
settles the issue by making the core function usb_gadget_disconnect()
issue the callback, so that UDC drivers don't need to worry about it.
A description of the new behavior is added to the function's
kerneldoc. Also, the patch removes a few superseded callbacks from
other core routines.
Future patches will remove the ->disconnect() calls from the UDC
drivers that make them, as they are now unnecessary. Until all those
patches are merged gadget drivers may receive extra ->disconnect()
callbacks, but this should be harmless.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
'optimizations' was misspelled as 'optmizations'. Fixed it. It is a
coding style change which should have no impact on runtime execution of code.
Signed-off-by: Faisal Mehmood <f.m3hm00d@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The name is always non-NULL and then is not used anywhere in this function,
so remove it.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-usb@vger.kernel.org
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The original implementation from commit b504882da5
("USB: add Freescale high-speed USB SOC device controller driver")
returned NULL on failure and an allocated + initialized struct fsl_udc on
success. The current code introduced in commit 4365831dad
("USB: fsl_usb2_udc: Get max ep number from DCCPARAMS register") only
provides partial initialization as well as returning 0 on success and -1
on failures. The function documentation is updated accordingly.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 4365831dad ("USB: fsl_usb2_udc: Get max ep number from DCCPARAMS register")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The allocation with fsl_alloc_request() and kmalloc() were unchecked
fixed this up with a NULL check and appropriate cleanup.
Additionally udc->ep_qh_size was reset to 0 on failure of allocation.
Similar udc->phy_mode is initially 0 (as udc_controller was
allocated with kzalloc in fsl_udc_probe()) so reset it to 0 as well
so that this function is side-effect free on failure. Not clear if
this is necessary or sensible as fsl_udc_release() probably can not
be called if fsl_udc_probe() failed - but it should not hurt.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: b504882da5 ("USB: add Freescale high-speed USB SOC device controller driver")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The vbus rise & fall interrupts are used to enable and disable
U3 function of device automatically, this cause some issues when
class driver is initialized as deactivated, and will skip over
software-controlled connect by pullup(), but UDC wants to keep
disconnect until usb_gadget_activate() is called which calls
pullup() if needed. So we disable vbus rise & fall interrupts
and just use pullup() to enable & disable U3 function, and reset
mtu3 state when disconnect instead when vbus fall.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
R-Car Gen3 needs to enable clocks of both host and peripheral.
Since [eo]hci-platform disables the reset(s) when the drivers are
removed, renesas_usbhs driver doesn't work correctly. To fix this
issue, this patch adds multiple clocks management on this
renesas_usbhs driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
R-Car Gen3 needs to enable clocks of both host and peripheral.
Otherwise, other side device cannot work correctly. So, this patch
adds a property of clock-names for R-Car Gen3 as an optional.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
R-Car Gen3 needs to deassert resets of both host and peripheral.
Since [eo]hci-platform is possible to assert the reset(s) when
the probing failed, renesas_usbhs driver doesn't work correctly
regardless of finished probing. To fix this issue, this patch adds
reset_control on this renesas_usbhs driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When operating in USB 2.0 speeds (HS/FS), if GUSB2PHYCFG.ENBLSLPM or
GUSB2PHYCFG.SUSPHY is set, it must be cleared before issuing an endpoint
command.
Current implementation only save and restore GUSB2PHYCFG.SUSPHY
configuration. We must save and clear both GUSB2PHYCFG.ENBLSLPM and
GUSB2PHYCFG.SUSPHY settings. Restore them after the command is
completed.
DWC_usb3 3.30a and DWC_usb31 1.90a programming guide section 3.2.2
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In Family 17h, some L3 Cache Performance events require the ThreadMask
and SliceMask to be set. For other events, these fields do not affect
the count either way.
Set ThreadMask and SliceMask to 0xFF and 0xF respectively.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H . Peter Anvin <hpa@zytor.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Suravee <Suravee.Suthikulpanit@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/Message-ID:
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The counters on M3UPI Link 0 and Link 3 don't count properly, and writing
0 to these counters may causes system crash on some machines.
The PCI BDF addresses of the M3UPI in the current code are incorrect.
The correct addresses should be:
D18:F1 0x204D
D18:F2 0x204E
D18:F5 0x204D
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: cd34cd97b7 ("perf/x86/intel/uncore: Add Skylake server uncore support")
Link: http://lkml.kernel.org/r/1537538826-55489-1-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some of the scheduling tracepoints allow the perf_tp_event
code to write to ring buffer under different cpu than the
code is running on.
This results in corrupted ring buffer data demonstrated in
following perf commands:
# perf record -e 'sched:sched_switch,sched:sched_wakeup' perf bench sched messaging
# Running 'sched/messaging' benchmark:
# 20 sender and receiver processes per group
# 10 groups == 400 processes run
Total time: 0.383 [sec]
[ perf record: Woken up 8 times to write data ]
0x42b890 [0]: failed to process type: -1765585640
[ perf record: Captured and wrote 4.825 MB perf.data (29669 samples) ]
# perf report --stdio
0x42b890 [0]: failed to process type: -1765585640
The reason for the corruption are some of the scheduling tracepoints,
that have __perf_task dfined and thus allow to store data to another
cpu ring buffer:
sched_waking
sched_wakeup
sched_wakeup_new
sched_stat_wait
sched_stat_sleep
sched_stat_iowait
sched_stat_blocked
The perf_tp_event function first store samples for current cpu
related events defined for tracepoint:
hlist_for_each_entry_rcu(event, head, hlist_entry)
perf_swevent_event(event, count, &data, regs);
And then iterates events of the 'task' and store the sample
for any task's event that passes tracepoint checks:
ctx = rcu_dereference(task->perf_event_ctxp[perf_sw_context]);
list_for_each_entry_rcu(event, &ctx->event_list, event_entry) {
if (event->attr.type != PERF_TYPE_TRACEPOINT)
continue;
if (event->attr.config != entry->type)
continue;
perf_swevent_event(event, count, &data, regs);
}
Above code can race with same code running on another cpu,
ending up with 2 cpus trying to store under the same ring
buffer, which is specifically not allowed.
This patch prevents the problem, by allowing only events with the same
current cpu to receive the event.
NOTE: this requires the use of (per-task-)per-cpu buffers for this
feature to work; perf-record does this.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
[peterz: small edits to Changelog]
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andrew Vagin <avagin@openvz.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: e6dab5ffab ("perf/trace: Add ability to set a target task for events")
Link: http://lkml.kernel.org/r/20180923161343.GB15054@krava
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When we unregister a PMU, we fail to serialize the @pmu_idr properly.
Fix that by doing the entire thing under pmu_lock.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: 2e80a82a49 ("perf: Dynamic pmu types")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When using external vbus supply regulator, it should be enabled
synchronously with PWR bit in HPRT register. This also fixes
unbalanced use of this optional regulator (This can be reproduced
easily when unbinding the driver).
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dwc2_vbus_supply_exit() may call regulator_disable(). It shouldn't be
called with interrupts disabled as it might sleep.
This is seen with DEBUG_ATOMIC_SLEEP=y.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There's a race with root hub resume, when using external vbus supply.
Root hub gets resumed, but runtime pm autosuspend runs as external vbus
supply isn't enabled. So, host never exit from power down properly.
Initialize vbus external supply before, rater that after hub resume.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Move devm_regulator_get_optional() call to probe routine. This avoids
'vbus-supply' regulator to be requested lots of times, upon each call
to dwc2_vbus_supply_init(), e.g. like with runtime pm.
Fixes: 531ef5ebea ("usb: dwc2: add support for host mode external
vbus supply")
Tested-by: Artur Petrosyan <arturp@synopsys.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Like the omap back-end, we get a link error with CONFIG_EXTCON=m
when building the qcom back-end into the kernel:
drivers/usb/dwc3/dwc3-qcom.o: In function `dwc3_qcom_probe':
dwc3-qcom.c:(.text+0x13dc): undefined reference to `extcon_get_edev_by_phandle'
dwc3-qcom.c:(.text+0x1b18): undefined reference to `devm_extcon_register_notifier'
dwc3-qcom.c:(.text+0x1b9c): undefined reference to `extcon_get_state'
Do the same thing as OMAP and add an explicit dependency on
EXTCON.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The at91sam9rl PMC is not quite the same as the at91sam9g45 one and now has
its own compatible string. Add support for that.
Fixes: 217bace8e548 ("ARM: dts: fix PMC compatible")
Acked-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The driver may sleep in an interrupt handler.
The function call path (from bottom to top) in Linux-4.17 is:
[FUNC] fotg210_ep_queue(GFP_KERNEL)
drivers/usb/gadget/udc/fotg210-udc.c, 744:
fotg210_ep_queue in fotg210_get_status
drivers/usb/gadget/udc/fotg210-udc.c, 768:
fotg210_get_status in fotg210_setup_packet
drivers/usb/gadget/udc/fotg210-udc.c, 949:
fotg210_setup_packet in fotg210_irq (interrupt handler)
To fix this bug, GFP_KERNEL is replaced with GFP_ATOMIC.
If possible, spin_unlock() and spin_lock() around fotg210_ep_queue()
can be also removed.
This bug is found by my static analysis tool DSAC.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabling all EP's allow to reset EP's to initial state.
On disconnect disable all EP's instead of just killing
all requests. Because of some platform didn't catch
disconnect event, same stuff added to
dwc2_hsotg_core_init_disconnected() function when USB
reset detected on the bus.
Changed from version 1:
Changed lock acquire flow in dwc2_hsotg_ep_disable()
function.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC3 variant found in Exynos5433 SoCs requires keeping all DRD30/UHOST30
clocks enabled all the time the driver does any access to DWC3 registers,
otherwise external abort happens. So far DWC3 hardware module worked with
samsung,exynos5250-dwusb3 compatible only by luck when built into kernel:
all DRD30 clocks were left enabled by bootloader and later kept enabled
by the DRD PHY driver. However, if one tried to use Exnos DWC3 driver as
a module or performed system suspend/resume cycle, external abort
happened. This patch finally fixes this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Yoshihiro Shimoda