Right now, cross-tree bridging setups work somewhat by mistake.
In the case of cross-tree bridging with sja1105, all switch instances
need to agree upon a common VLAN ID for forwarding a packet that belongs
to a certain bridging domain.
With TX forwarding offload, the VLAN ID is the bridge VLAN for
VLAN-aware bridging, and the tag_8021q TX forwarding offload VID
(a VLAN which has non-zero VBID bits) for VLAN-unaware bridging.
The VBID for VLAN-unaware bridging is derived from the dp->bridge_num
value calculated by DSA independently for each switch tree.
If ports from one tree join one bridge, and ports from another tree join
another bridge, DSA will assign them the same bridge_num, even though
the bridges are different. If cross-tree bridging is supported, this
is an issue.
Modify DSA to calculate the bridge_num globally across all switch trees.
This has the implication for a driver that the dp->bridge_num value that
DSA will assign to its ports might not be contiguous, if there are
boards with multiple DSA drivers instantiated. Additionally, all
bridge_num values eat up towards each switch's
ds->num_fwd_offloading_bridges maximum, which is potentially unfortunate,
and can be seen as a limitation introduced by this patch. However, that
is the lesser evil for now.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* BSS coloring support
* MEI commands for Intel platforms
* various fixes/cleanups
-----BEGIN PGP SIGNATURE-----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=q8bL
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2021-08-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Minor updates:
* BSS coloring support
* MEI commands for Intel platforms
* various fixes/cleanups
* tag 'mac80211-next-for-net-next-2021-08-20' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next:
cfg80211: fix BSS color notify trace enum confusion
mac80211: Fix insufficient headroom issue for AMSDU
mac80211: add support for BSS color change
nl80211: add support for BSS coloring
mac80211: Use flex-array for radiotap header bitmap
mac80211: radiotap: Use BIT() instead of shifts
mac80211: Remove unnecessary variable and label
mac80211: include <linux/rbtree.h>
mac80211: Fix monitor MTU limit so that A-MSDUs get through
mac80211: remove unnecessary NULL check in ieee80211_register_hw()
mac80211: Reject zero MAC address in sta_info_insert_check()
nl80211: vendor-cmd: add Intel vendor commands for iwlmei usage
====================
Link: https://lore.kernel.org/r/20210820105329.48674-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The per-vlan router option controls the port/vlan and host vlan entries'
mcast router config. The global option controlled only the host vlan
config, but that is unnecessary and incosistent as it's not really a
global vlan option, but rather bridge option to control host router
config, so convert BRIDGE_VLANDB_GOPTS_MCAST_ROUTER to
BRIDGE_VLANDB_ENTRY_MCAST_ROUTER which can be used to control both host
vlan and port vlan mcast router config.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change br_multicast_set_port_router to take port multicast context as
its first argument so we can later use it to control port/vlan mcast
router option.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add support for Foxconn Mediatek Chip
- Add support for LG LGSBWAC92/TWCM-K505D
- hci_h5 flow control fixes and suspend support
- Switch to use lock_sock for SCO and RFCOMM
- Various fixes for extended advertising
- Reword Intel's setup on btusb unifying the supported generations
-----BEGIN PGP SIGNATURE-----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=INb2
-----END PGP SIGNATURE-----
Merge tag 'for-net-next-2021-08-19' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
- Add support for Foxconn Mediatek Chip
- Add support for LG LGSBWAC92/TWCM-K505D
- hci_h5 flow control fixes and suspend support
- Switch to use lock_sock for SCO and RFCOMM
- Various fixes for extended advertising
- Reword Intel's setup on btusb unifying the supported generations
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- bump version strings, by Simon Wunderlich
- update docs about move IRC channel away from freenode,
by Sven Eckelmann
- Switch to kstrtox.h for kstrtou64, by Sven Eckelmann
- Update NULL checks, by Sven Eckelmann (2 patches)
- remove remaining skb-copy calls for broadcast packets,
by Linus Lüssing
-----BEGIN PGP SIGNATURE-----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=sHz+
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-pullrequest-20210819' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- update docs about move IRC channel away from freenode,
by Sven Eckelmann
- Switch to kstrtox.h for kstrtou64, by Sven Eckelmann
- Update NULL checks, by Sven Eckelmann (2 patches)
- remove remaining skb-copy calls for broadcast packets,
by Linus Lüssing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
hci_error_reset() return without calling hci_dev_do_open() when
hci_dev_do_close() return error value which is not 0.
Also, hci_dev_close() return hci_dev_do_close() function's return
value.
But, hci_dev_do_close() return always 0 even if hdev->shutdown
return error value. So, fix hci_dev_do_close() to save and return
the return value of the hdev->shutdown when it is called.
Signed-off-by: Kangmin Park <l4stpr0gr4m@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Syzbot hit "task hung" bug in hci_req_sync(). The problem was in
unreasonable huge inquiry timeout passed from userspace.
Fix it by adding sanity check for timeout value to hci_inquiry().
Since hci_inquiry() is the only user of hci_req_sync() with user
controlled timeout value, it makes sense to check timeout value in
hci_inquiry() and don't touch hci_req_sync().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Reported-and-tested-by: syzbot+be2baed593ea56c6a84c@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
After gaining __alloc_size hints, GCC thinks it can reach a memcpy()
with eir_len == 0 (since it can't see into the rewrite of status).
Instead, check eir_len == 0, avoiding this future warning:
In function 'eir_append_data',
inlined from 'read_local_oob_ext_data_complete' at net/bluetooth/mgmt.c:7210:12:
./include/linux/fortify-string.h:54:29: warning: '__builtin_memcpy' offset 5 is out of the bounds [0, 3] [-Warray-bounds]
...
net/bluetooth/hci_request.h:133:2: note: in expansion of macro 'memcpy'
133 | memcpy(&eir[eir_len], data, data_len);
| ^~~~~~
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-bluetooth@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently, when creating an ingress qdisc on an indirect device before
the driver registered for callbacks, the driver will not have a chance
to register its filter configuration callbacks.
To fix that, modify the code such that it keeps track of all the ingress
qdiscs that call flow_indr_dev_setup_offload(). When a driver calls
flow_indr_dev_register(), go through the list of tracked ingress qdiscs
and call the driver callback entry point so as to give it a chance to
register its callback.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rcu field is not used. Remove it.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Eli Cohen <elic@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If directly after an MP_CAPABLE 3WHS, the client receives an ADD_ADDR
with HMAC from the server, it is enough to switch to a "fully
established" mode because it has received more MPTCP options.
It was then OK to enable the "fully_established" flag on the MPTCP
socket. Still, best to check if the ADD_ADDR looks valid by looking if
it contains an HMAC (no 'echo' bit). If an ADD_ADDR echo is received
while we are not in "fully established" mode, it is strange and then
we should not switch to this mode now.
But that is not enough. On one hand, the path-manager has be notified
the state has changed. On the other hand, the "fully_established" flag
on the subflow socket should be turned on as well not to re-send the
MP_CAPABLE 3rd ACK content with the next ACK.
Fixes: 84dfe3677a ("mptcp: send out dedicated ADD_ADDR packet")
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function "dma_map_sg" is entitled to merge adjacent entries
and return a value smaller than what was passed as "nents".
Subsequently "ib_map_mr_sg" needs to work with this value ("sg_dma_len")
rather than the original "nents" parameter ("sg_len").
This old RDS bug was exposed and reliably causes kernel panics
(using RDMA operations "rds-stress -D") on x86_64 starting with:
commit c588072bba ("iommu/vt-d: Convert intel iommu driver to the iommu ops")
Simply put: Linux 5.11 and later.
Signed-off-by: Gerd Rausch <gerd.rausch@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Link: https://lore.kernel.org/r/60efc69f-1f35-529d-a7ef-da0549cad143@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We currently have two code paths for broadcast packets:
A) self-generated, via batadv_interface_tx()->
batadv_send_bcast_packet().
B) received/forwarded, via batadv_recv_bcast_packet()->
batadv_forw_bcast_packet().
For A), self-generated broadcast packets:
The only modifications to the skb data is the ethernet header which is
added/pushed to the skb in
batadv_send_broadcast_skb()->batadv_send_skb_packet(). However before
doing so, batadv_skb_head_push() is called which calls skb_cow_head() to
unshare the space for the to be pushed ethernet header. So for this
case, it is safe to use skb clones.
For B), received/forwarded packets:
The same applies as in A) for the to be forwarded packets. Only the
ethernet header is added. However after (queueing for) forwarding the
packet in batadv_recv_bcast_packet()->batadv_forw_bcast_packet(), a
packet is additionally decapsulated and is sent up the stack through
batadv_recv_bcast_packet()->batadv_interface_rx().
Protocols higher up the stack are already required to check if the
packet is shared and create a copy for further modifications. When the
next (protocol) layer works correctly, it cannot happen that it tries to
operate on the data behind the skb clone which is still queued up for
forwarding.
Co-authored-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Currently, the declaration of fill_imix_distribution() is dependent
on CONFIG_XFRM. This is incorrect.
Move fill_imix_distribution() declaration out of #ifndef CONFIG_XFRM
block.
Signed-off-by: Nick Richardson <richardsonnick@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add gfp_t mask as an input parameter to mem_cgroup_charge_skmem(),
to give more control to the networking stack and enable it to change
memcg charging behavior. In the future, the networking stack may decide
to avoid oom-kills when fallbacks are more appropriate.
One behavior change in mem_cgroup_charge_skmem() by this patch is to
avoid force charging by default and let the caller decide when and if
force charging is needed through the presence or absence of
__GFP_NOFAIL.
Signed-off-by: Wei Wang <weiwan@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fq qdisc requires tstamp to be cleared in the forwarding path. Now ovs
doesn't clear skb->tstamp. We encountered a problem with linux
version 5.4.56 and ovs version 2.14.1, and packets failed to
dequeue from qdisc when fq qdisc was attached to ovs port.
Fixes: fb420d5d91 ("tcp/fq: move back to CLOCK_MONOTONIC")
Signed-off-by: kaixi.fan <fankaixi.li@bytedance.com>
Signed-off-by: xiexiaohui <xiexiaohui.xxh@bytedance.com>
Reviewed-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is only one caller for ops_free(), so inline it.
Separate net_drop_ns() and net_free(), so the net_free()
can be called directly.
Add free_exit_list() helper function for free net_exit_list.
====================
v2:
- v1 does not apply, rebase it.
====================
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for tag_sja1105 running on non-sja1105 DSA ports, by making
sure that every time we dereference dp->priv, we check the switch's
dsa_switch_ops (otherwise we access a struct sja1105_port structure that
is in fact something else).
This adds an unconditional build-time dependency between sja1105 being
built as module => tag_sja1105 must also be built as module. This was
there only for PTP before.
Some sane defaults must also take place when not running on sja1105
hardware. These are:
- sja1105_xmit_tpid: the sja1105 driver uses different VLAN protocols
depending on VLAN awareness and switch revision (when an encapsulated
VLAN must be sent). Default to 0x8100.
- sja1105_rcv_meta_state_machine: this aggregates PTP frames with their
metadata timestamp frames. When running on non-sja1105 hardware, don't
do that and accept all frames unmodified.
- sja1105_defer_xmit: calls sja1105_port_deferred_xmit in sja1105_main.c
which writes a management route over SPI. When not running on sja1105
hardware, bypass the SPI write and send the frame as-is.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding support for using the skb->hash value as the flow hash in CAKE,
I accidentally introduced a logic error that broke the host-only isolation
modes of CAKE (srchost and dsthost keywords). Specifically, the flow_hash
variable should stay initialised to 0 in cake_hash() in pure host-based
hashing mode. Add a check for this before using the skb->hash value as
flow_hash.
Fixes: b0c19ed608 ("sch_cake: Take advantage of skb->hash where appropriate")
Reported-by: Pete Heist <pete@heistp.net>
Tested-by: Pete Heist <pete@heistp.net>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add seq_puts() statement for dev_mcast, make it more readable.
As also, keep vertical alignment for {dev, ptype, dev_mcast} that
under /proc/net.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make all dependent RxRPC kconfig entries be dependent on AF_RXRPC
so that they are presented (indented) after AF_RXRPC instead
of being presented at the same level on indentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Marc Dionne <marc.dionne@auristor.com>
Cc: linux-afs@lists.infradead.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
In mptcp_pm_nl_add_addr_received(), fill a temporary allocate array of
all local address corresponding to the fullmesh endpoint. If such array
is empty, keep the current behavior.
Elsewhere loop on such array and create a subflow for each local address
towards the given remote address
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added and managed a new per endpoint flag, named
MPTCP_PM_ADDR_FLAG_FULLMESH.
In mptcp_pm_create_subflow_or_signal_addr(), if such flag is set, instead
of:
remote_address((struct sock_common *)sk, &remote);
fill a temporary allocated array of all known remote address. After
releaseing the pm lock loop on such array and create a subflow for each
remote address from the given local.
Note that the we could still use an array even for non 'fullmesh'
endpoint: with a single entry corresponding to the primary MPC subflow
remote address.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added a new helper mptcp_pm_get_flags_and_ifindex_by_id(),
and used it in __mptcp_subflow_connect() to get the flags and ifindex
values.
Then the two arguments flags and ifindex of __mptcp_subflow_connect()
can be dropped.
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong enum was used here, leading to warnings.
Just use a u32 instead.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 0d2ab3aea5 ("nl80211: add support for BSS coloring")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The color change announcement is very similar to how CSA works where
we have an IE that includes a counter. When the counter hits 0, the new
color is applied via an updated beacon.
This patch makes the CSA counter functionality reusable, rather than
implementing it again. This also allows for future reuse incase support
for other counter IEs gets added.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/057c1e67b82bee561ea44ce6a45a8462d3da6995.1625247619.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support for BSS color collisions to the wireless subsystem.
Add the required functionality to nl80211 that will notify about color
collisions, triggering the color change and notifying when it is completed.
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: John Crispin <john@phrozen.org>
Link: https://lore.kernel.org/r/500b3582aec8fe2c42ef46f3117b148cb7cbceb5.1625247619.git.lorenzo@kernel.org
[remove unnecessary NULL initialisation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When changing vlan mcast state by br_multicast_toggle_vlan it iterates
over all ports and enables/disables the port mcast ctx based on the new
state, but I forgot to update the host vlan (bridge master vlan entry)
with the new state so it will be left out. Also that function is not
used outside of br_multicast.c, so make it static.
Fixes: f4b7002a70 ("net: bridge: add vlan mcast snooping knob")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending a global vlan notification we should account for the number
of router ports when allocating the skb, otherwise we might end up
losing notifications.
Fixes: dc002875c2 ("net: bridge: vlan: use br_rports_fill_info() to export mcast router ports")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We always create a vlan with enabled mcast snooping, so when the user
turns on per-vlan mcast contexts they'll get consistent behaviour with
the current situation, but one place wasn't updated when a bridge/master
vlan which already exists (created due to port vlans) is being added as
real bridge vlan (BRIDGE_VLAN_INFO_BRENTRY). We need to enable mcast
snooping for that vlan when that happens.
Fixes: 7b54aaaf53 ("net: bridge: multicast: add vlan state initialization and control")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the original TFO server code was implemented in commit
168a8f5805 ("tcp: TCP Fast Open Server -
main code path") the TFO server code has supported the sysctl bit flag
TFO_SERVER_COOKIE_NOT_REQD. Currently, when the TFO_SERVER_ENABLE and
TFO_SERVER_COOKIE_NOT_REQD sysctl bit flags are set, a server connection
will accept a SYN with N bytes of data (N > 0) that has no TFO cookie,
create a new fast open connection, process the incoming data in the SYN,
and make the connection ready for accepting. After accepting, the
connection is ready for read()/recvmsg() to read the N bytes of data in
the SYN, ready for write()/sendmsg() calls and data transmissions to
transmit data.
This commit changes an edge case in this feature by changing this
behavior to apply to (N >= 0) bytes of data in the SYN rather than only
(N > 0) bytes of data in the SYN. Now, a server will accept a data-less
SYN without a TFO cookie if TFO_SERVER_COOKIE_NOT_REQD is set.
Caveat! While this enables a new kind of TFO (data-less empty-cookie
SYN), some firewall rules setup may not work if they assume such packets
are not legit TFOs and will filter them.
Signed-off-by: Luke Hsiao <lukehsiao@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20210816205105.2533289-1-luke.w.hsiao@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For NOP command, need to cancel work scheduled on cmd_timer,
on receiving command status or commmand complete event.
Below use case might lead to race condition multiple when NOP
commands are queued sequentially:
hci_cmd_work() {
if (atomic_read(&hdev->cmd_cnt) {
.
.
.
atomic_dec(&hdev->cmd_cnt);
hci_send_frame(hdev,...);
schedule_delayed_work(&hdev->cmd_timer,...);
}
}
On receiving event for first NOP, the work scheduled on hdev->cmd_timer
is not cancelled and second NOP is dequeued and sent to controller.
While waiting for an event for second NOP command, work scheduled on
cmd_timer for the first NOP can get scheduled, resulting in sending third
NOP command (sending back to back NOP commands). This might
cause issues at controller side (like memory overrun, controller going
unresponsive) resulting in hci tx timeouts, hardware errors etc.
The fix to this issue is to cancel the delayed work scheduled on
cmd_timer on receiving command status or command complete event for
NOP command (this patch handles NOP command same as any other SIG
command).
Signed-off-by: Kiran K <kiran.k@intel.com>
Reviewed-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Reviewed-by: Srivatsa Ravishankar <ravishankar.srivatsa@intel.com>
Acked-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This stores the advertising handle/instance into hci_conn so it is
accessible when re-enabling the advertising once disconnected.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
LE Enhanced Connection Complete contains the Local RPA used in the
connection which must be used when set otherwise there could problems
when pairing since the address used by the remote stack could be the
Local RPA:
BLUETOOTH CORE SPECIFICATION Version 5.2 | Vol 4, Part E
page 2396
'Resolvable Private Address being used by the local device for this
connection. This is only valid when the Own_Address_Type (from the
HCI_LE_Create_Connection, HCI_LE_Set_Advertising_Parameters,
HCI_LE_Set_Extended_Advertising_Parameters, or
HCI_LE_Extended_Create_Connection commands) is set to 0x02 or
0x03, and the Controller generated a resolvable private address for the
local device using a non-zero local IRK. For other Own_Address_Type
values, the Controller shall return all zeros.'
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Commit 0ea9fd001a ("Bluetooth: Shutdown controller after workqueues
are flushed or cancelled") introduced a regression that makes mtkbtsdio
driver stops working:
[ 36.593956] Bluetooth: hci0: Firmware already downloaded
[ 46.814613] Bluetooth: hci0: Execution of wmt command timed out
[ 46.814619] Bluetooth: hci0: Failed to send wmt func ctrl (-110)
The shutdown callback depends on the result of hdev->rx_work, so we
should call it before flushing rx_work:
-> btmtksdio_shutdown()
-> mtk_hci_wmt_sync()
-> __hci_cmd_send()
-> wait for BTMTKSDIO_TX_WAIT_VND_EVT gets cleared
-> btmtksdio_recv_event()
-> hci_recv_frame()
-> queue_work(hdev->workqueue, &hdev->rx_work)
-> clears BTMTKSDIO_TX_WAIT_VND_EVT
So move the shutdown callback before flushing TX/RX queue to resolve the
issue.
Reported-and-tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Fixes: 0ea9fd001a ("Bluetooth: Shutdown controller after workqueues are flushed or cancelled")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We need to account for the IPv6 attributes when dumping querier state.
Fixes: 5e924fe6ccfd ("net: bridge: mcast: dump ipv6 querier state")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was a dumb error I made instead of writing nla_total_size(0)
for a nest attribute, I wrote nla_total_size(sizeof(0)).
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 606433fe3e11 ("net: bridge: mcast: dump ipv4 querier state")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A minor improvement to avoid dumping mcast ctx querier state if snooping
is disabled for that context (either bridge or vlan).
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__tipc_sendmsg() is called to send SYN packet by either tipc_sendmsg()
or tipc_connect(). The difference is in tipc_connect(), it will call
tipc_wait_for_connect() after __tipc_sendmsg() to wait until connecting
is done. So there's no need to wait in __tipc_sendmsg() for this case.
This patch is to fix it by calling tipc_wait_for_connect() only when dlen
is not 0 in __tipc_sendmsg(), which means it's called by tipc_connect().
Note this also fixes the failure in tipcutils/test/ptts/:
# ./tipcTS &
# ./tipcTC 9
(hang)
Fixes: 36239dab6da7 ("tipc: fix implicit-connect for SYN+")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the development of the blamed patch, the "bool broadcast"
argument of dsa_port_tag_8021q_vlan_{add,del} was originally called
"bool local", and the meaning was the exact opposite.
Due to a rookie mistake where the patch was modified at the last minute
without retesting, the instances of dsa_port_tag_8021q_vlan_{add,del}
are called with the wrong values. During setup and teardown, cross-chip
notifiers should not be broadcast to all DSA trees, while during
bridging, they should.
Fixes: 724395f4dc ("net: dsa: tag_8021q: don't broadcast during setup/teardown")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
edumazet@google.com pointed out that queue_oob
does not check socket state after acquiring
the lock. He also pointed to an incorrect usage
of kfree_skb and an unnecessary setting of skb
length. This patch addresses those issue.
Signed-off-by: Rao Shoaib <Rao.Shoaib@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new mcast querier state dump infrastructure and export vlans'
mcast context querier state embedded in attribute
BRIDGE_VLANDB_GOPTS_MCAST_QUERIER_STATE.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for dumping global IPv6 querier state, we dump the state
only if our own querier is enabled or there has been another external
querier which has won the election. For the bridge global state we use
a new attribute IFLA_BR_MCAST_QUERIER_STATE and embed the state inside.
The structure is:
[IFLA_BR_MCAST_QUERIER_STATE]
`[BRIDGE_QUERIER_IPV6_ADDRESS] - ip address of the querier
`[BRIDGE_QUERIER_IPV6_PORT] - bridge port ifindex where the querier
was seen (set only if external querier)
`[BRIDGE_QUERIER_IPV6_OTHER_TIMER] - other querier timeout
IPv4 and IPv6 attributes are embedded at the same level of
IFLA_BR_MCAST_QUERIER_STATE. If we didn't dump anything we cancel the nest
and return.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for dumping global IPv4 querier state, we dump the state
only if our own querier is enabled or there has been another external
querier which has won the election. For the bridge global state we use
a new attribute IFLA_BR_MCAST_QUERIER_STATE and embed the state inside.
The structure is:
[IFLA_BR_MCAST_QUERIER_STATE]
`[BRIDGE_QUERIER_IP_ADDRESS] - ip address of the querier
`[BRIDGE_QUERIER_IP_PORT] - bridge port ifindex where the querier was
seen (set only if external querier)
`[BRIDGE_QUERIER_IP_OTHER_TIMER] - other querier timeout
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vladimir Oltean