macb_64b_desc is always called when HW_DMA_CAP_64B is defined.
So the return NULL can never be reached. Remove the dead code.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Flow Control selftest is also available with ASYM Pause. Lets add
this check to the test and fix eventual false positive failures.
Fixes: 091810dbde ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warning:
drivers/net/ethernet/freescale/gianfar.c:2070:6:
warning: symbol 'reset_gfar' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code allows more than one thread to run in reset. This can
corrupt struct adapter data. Check adapter->resetting before performing
a reset, if there is another reset running delay (100 msec) before trying
again.
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a5681e20b5 ("net/ibmnvic: Fix deadlock problem in reset")
made the change to hold the RTNL lock during a reset to avoid deadlock
but linkwatch_event is fired during the reset and needs the RTNL lock.
That keeps linkwatch_event process from proceeding until the reset
is complete. The reset process cannot tolerate the linkwatch_event
processing after reset completes, so release the RTNL lock during the
process to allow a chance for linkwatch_event to run during reset.
This does not guarantee that the linkwatch_event will be processed as
soon as link state changes, but is an improvement over the current code
where linkwatch_event processing is always delayed, which prevents
transmissions on the device from being deactivated leading transmit
watchdog timer to time-out.
Release the RTNL lock before link state change and re-acquire after
the link state change to allow linkwatch_event to grab the RTNL lock
and run during the reset.
Fixes: a5681e20b5 ("net/ibmnvic: Fix deadlock problem in reset")
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Running old skge driver on PowerPC causes checksum errors
because hardware reported 1's complement checksum is in little-endian
byte order.
Reported-by: Benoit <benoit.sansoni@gmail.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct archdr is only big enough to hold the header of various types of
arcnet packets. So to provide enough space to hold the data read from
hardware provide a buffer large enough to hold a packet with maximal
size.
The problem was noticed by the stack protector which makes the kernel
oops.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects the SPDX License Identifier style
in header file for Distributed Switch Architecture drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch corrects the SPDX License Identifier style
in header file for Broadcom BCM53xx managed switch driver.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
We need to set the error code on this path. Otherwise it probably
results in a NULL dereference down the line.
Fixes: aa3198819b ("ionic: Add RSS support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
If CONFIG_ENA_ETHERNET=y and CONFIG_DIMLIB=n,
below erros can be found:
drivers/net/ethernet/amazon/ena/ena_netdev.o: In function `ena_dim_work':
ena_netdev.c:(.text+0x21cc): undefined reference to `net_dim_get_rx_moderation'
ena_netdev.c:(.text+0x21cc): relocation truncated to
fit: R_AARCH64_CALL26 against undefined symbol `net_dim_get_rx_moderation'
drivers/net/ethernet/amazon/ena/ena_netdev.o: In function `ena_io_poll':
ena_netdev.c:(.text+0x7bd4): undefined reference to `net_dim'
ena_netdev.c:(.text+0x7bd4): relocation truncated to fit:
R_AARCH64_CALL26 against undefined symbol `net_dim'
After commit 282faf61a0 ("net: ena: switch to dim algorithm for rx adaptive
interrupt moderation"), it introduces dim algorithm, which configured by CONFIG_DIMLIB.
So, this patch is to select DIMLIB for ENA_ETHERNET.
Fixes: 282faf61a0 ("net: ena: switch to dim algorithm for rx adaptive interrupt moderation")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Use 'skb_put_data()' instead of rewritting it.
This improves readability.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Putting a struct stmmac_rss object on the stack is a bad idea,
as it exceeds the warning limit for a stack frame on 32-bit architectures:
drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c:1221:12: error: stack frame size of 1208 bytes in function '__stmmac_test_l3filt' [-Werror,-Wframe-larger-than=]
drivers/net/ethernet/stmicro/stmmac/stmmac_selftests.c:1338:12: error: stack frame size of 1208 bytes in function '__stmmac_test_l4filt' [-Werror,-Wframe-larger-than=]
As the object is the trivial empty case, change the called function
to accept a NULL pointer to mean the same thing and remove the
large variable in the two callers.
Fixes: 4647e02119 ("net: stmmac: selftests: Add selftest for L3/L4 Filters")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
If CONFIG_NET_DSA_SJA1105_TAS=y and CONFIG_NET_SCH_TAPRIO=n,
below error can be found:
drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_setup_tc_taprio':
sja1105_tas.c:(.text+0x318): undefined reference to `taprio_offload_free'
sja1105_tas.c:(.text+0x590): undefined reference to `taprio_offload_get'
drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_tas_teardown':
sja1105_tas.c:(.text+0x610): undefined reference to `taprio_offload_free'
make: *** [vmlinux] Error 1
sja1105_tas needs tc-taprio, so this patch add the dependency for it.
Fixes: 317ab5b86c ("net: dsa: sja1105: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The ARM netx platform got removed in 5.3, so this driver
is now useless.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
According to the DP83865 datasheet "the 10 Mbps HDX loopback can be
disabled in the expanded memory register 0x1C0.1". The driver erroneously
used bit 0 instead of bit 1.
Fixes: 4621bf1298 ("phy: Add file missed in previous commit.")
Signed-off-by: Peter Mamonov <pmamonov@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Endpoints with zero wMaxPacketSize are not usable for transferring
data. Ignore such endpoints when looking for valid in, out and
status pipes, to make the drivers more robust against invalid and
meaningless descriptors.
The wMaxPacketSize of these endpoints are used for memory allocations
and as divisors in many usbnet minidrivers. Avoiding zero is therefore
critical.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Endpoints with zero wMaxPacketSize are not usable for transferring
data. Ignore such endpoints when looking for valid in, out and
status pipes, to make the driver more robust against invalid and
meaningless descriptors.
The wMaxPacketSize of the out pipe is used as divisor. So this change
fixes a divide-by-zero bug.
Reported-by: syzbot+ce366e2b8296e25d84f5@syzkaller.appspotmail.com
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
With commit 0655f9943d ("net/ibmvnic: Update carrier state after link
state change") we are now able to detect when the carrier is properly
present in the device, so only report an unexpected unknown speed when it
is properly detected. Unknown speed is expected to be seen by the device
in case the backing device has no link detected.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Murilo Fossa Vicentini <muvic@linux.ibm.com>
Reviewed-by: Thomas Falcon <tlfalcon@linux.ibm.com>
clang warns:
../drivers/net/ethernet/pensando/ionic/ionic_debugfs.c:60:37: warning:
expression result unused [-Wunused-value]
ionic, &identity_fops) ? 0 : -EOPNOTSUPP;
^~~~~~~~~~~
1 warning generated.
The return value of debugfs_create_file does not need to be checked [1]
and the function returns void so get rid of the ternary operator, it is
unnecessary.
[1]: https://lore.kernel.org/linux-mm/20150815160730.GB25186@kroah.com/
Fixes: fbfb803153 ("ionic: Add hardware init and device commands")
Link: https://github.com/ClangBuiltLinux/linux/issues/658
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After a reset packet sizes and device mtu can change and need
to be reevaluated to calculate queue sizes.
Malicious devices can set this to zero and we divide by it.
Introduce sanity checking.
Reported-and-tested-by: syzbot+6102c120be558c885f04@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Support IPV6 RA Captive Portal Identifier, from Maciej Żenczykowski.
2) Use bio_vec in the networking instead of custom skb_frag_t, from
Matthew Wilcox.
3) Make use of xmit_more in r8169 driver, from Heiner Kallweit.
4) Add devmap_hash to xdp, from Toke Høiland-Jørgensen.
5) Support all variants of 5750X bnxt_en chips, from Michael Chan.
6) More RTNL avoidance work in the core and mlx5 driver, from Vlad
Buslov.
7) Add TCP syn cookies bpf helper, from Petar Penkov.
8) Add 'nettest' to selftests and use it, from David Ahern.
9) Add extack support to drop_monitor, add packet alert mode and
support for HW drops, from Ido Schimmel.
10) Add VLAN offload to stmmac, from Jose Abreu.
11) Lots of devm_platform_ioremap_resource() conversions, from
YueHaibing.
12) Add IONIC driver, from Shannon Nelson.
13) Several kTLS cleanups, from Jakub Kicinski.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1930 commits)
mlxsw: spectrum_buffers: Add the ability to query the CPU port's shared buffer
mlxsw: spectrum: Register CPU port with devlink
mlxsw: spectrum_buffers: Prevent changing CPU port's configuration
net: ena: fix incorrect update of intr_delay_resolution
net: ena: fix retrieval of nonadaptive interrupt moderation intervals
net: ena: fix update of interrupt moderation register
net: ena: remove all old adaptive rx interrupt moderation code from ena_com
net: ena: remove ena_restore_ethtool_params() and relevant fields
net: ena: remove old adaptive interrupt moderation code from ena_netdev
net: ena: remove code duplication in ena_com_update_nonadaptive_moderation_interval _*()
net: ena: enable the interrupt_moderation in driver_supported_features
net: ena: reimplement set/get_coalesce()
net: ena: switch to dim algorithm for rx adaptive interrupt moderation
net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it
net: phy: adin: implement Energy Detect Powerdown mode via phy-tunable
ethtool: implement Energy Detect Powerdown support via phy-tunable
xen-netfront: do not assume sk_buff_head list is empty in error handling
s390/ctcm: Delete unnecessary checks before the macro call “dev_kfree_skb”
net: ena: don't wake up tx queue when down
drop_monitor: Better sanitize notified packets
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXYAIeQAKCRBiEGxRG/Sl
2/SzAQDEnoNxzV/R5kWFd+2kmFeY3cll0d99KMrWJ8om+kje6QD/cXxZHzFm+T1L
UPF66k76oOODV7cyndjXnTnRXbeCRAM=
=Szby
-----END PGP SIGNATURE-----
Merge tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"In this cycle we've finally managed to contribute the patch set
sorting out LED naming issues. Besides that there are many changes
scattered among various LED class drivers and triggers.
LED naming related improvements:
- add new 'function' and 'color' fwnode properties and deprecate
'label' property which has been frequently abused for conveying
vendor specific names that have been available in sysfs anyway
- introduce a set of standard LED_FUNCTION* definitions
- introduce a set of standard LED_COLOR_ID* definitions
- add a new {devm_}led_classdev_register_ext() API with the
capability of automatic LED name composition basing on the
properties available in the passed fwnode; the function is
backwards compatible in a sense that it uses 'label' data, if
present in the fwnode, for creating LED name
- add tools/leds/get_led_device_info.sh script for retrieving LED
vendor, product and bus names, if applicable; it also performs
basic validation of an LED name
- update following drivers and their DT bindings to use the new LED
registration API:
- leds-an30259a, leds-gpio, leds-as3645a, leds-aat1290, leds-cr0014114,
leds-lm3601x, leds-lm3692x, leds-lp8860, leds-lt3593, leds-sc27xx-blt
Other LED class improvements:
- replace {devm_}led_classdev_register() macros with inlines
- allow to call led_classdev_unregister() unconditionally
- switch to use fwnode instead of be stuck with OF one
LED triggers improvements:
- led-triggers:
- fix dereferencing of null pointer
- fix a memory leak bug
- ledtrig-gpio:
- GPIO 0 is valid
Drop superseeded apu2/3 support from leds-apu since for apu2+ a newer,
more complete driver exists, based on a generic driver for the AMD
SOCs gpio-controller, supporting LEDs as well other devices:
- drop profile field from priv data
- drop iosize field from priv data
- drop enum_apu_led_platform_types
- drop superseeded apu2/3 led support
- add pr_fmt prefix for better log output
- fix error message on probing failure
Other misc fixes and improvements to existing LED class drivers:
- leds-ns2, leds-max77650:
- add of_node_put() before return
- leds-pwm, leds-is31fl32xx:
- use struct_size() helper
- leds-lm3697, leds-lm36274, leds-lm3532:
- switch to use fwnode_property_count_uXX()
- leds-lm3532:
- fix brightness control for i2c mode
- change the define for the fs current register
- fixes for the driver for stability
- add full scale current configuration
- dt: Add property for full scale current.
- avoid potentially unpaired regulator calls
- move static keyword to the front of declarations
- fix optional led-max-microamp prop error handling
- leds-max77650:
- add of_node_put() before return
- add MODULE_ALIAS()
- Switch to fwnode property API
- leds-as3645a:
- fix misuse of strlcpy
- leds-netxbig:
- add of_node_put() in netxbig_leds_get_of_pdata()
- remove legacy board-file support
- leds-is31fl319x:
- simplify getting the adapter of a client
- leds-ti-lmu-common:
- fix coccinelle issue
- move static keyword to the front of declaration
- leds-syscon:
- use resource managed variant of device register
- leds-ktd2692:
- fix a typo in the name of a constant
- leds-lp5562:
- allow firmware files up to the maximum length
- leds-an30259a:
- fix typo
- leds-pca953x:
- include the right header"
* tag 'leds-for-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds: (72 commits)
leds: lm3532: Fix optional led-max-microamp prop error handling
led: triggers: Fix dereferencing of null pointer
leds: ti-lmu-common: Move static keyword to the front of declaration
leds: lm3532: Move static keyword to the front of declarations
leds: trigger: gpio: GPIO 0 is valid
leds: pwm: Use struct_size() helper
leds: is31fl32xx: Use struct_size() helper
leds: ti-lmu-common: Fix coccinelle issue in TI LMU
leds: lm3532: Avoid potentially unpaired regulator calls
leds: syscon: Use resource managed variant of device register
leds: Replace {devm_}led_classdev_register() macros with inlines
leds: Allow to call led_classdev_unregister() unconditionally
leds: lm3532: Add full scale current configuration
dt: lm3532: Add property for full scale current.
leds: lm3532: Fixes for the driver for stability
leds: lm3532: Change the define for the fs current register
leds: lm3532: Fix brightness control for i2c mode
leds: Switch to use fwnode instead of be stuck with OF one
leds: max77650: Switch to fwnode property API
led: triggers: Fix a memory leak bug
...
The branch contains driver changes that are tightly
connected to SoC specific code. Aside from smaller
cleanups and bug fixes, here is a list of the notable
changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver
for its on-board pluggable extension bus. The
same platform also gains a firmware driver.
- The Samsung Exynos family gains a new Chipid driver
exporting using the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon
chips.
- A firmware driver for the NXP i.MX DSP IPC protocol
using shared memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the
NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for
the S905X3 and A311D chips
- A rework of the TI Davinci framebuffer driver to
allow important cleanups in the platform code
- A couple of device drivers for removed ARM SoC
platforms are removed. Most of the removals were
picked up by other maintainers, this contains
whatever was left.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lxFi
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This contains driver changes that are tightly connected to SoC
specific code. Aside from smaller cleanups and bug fixes, here is a
list of the notable changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver for its
on-board pluggable extension bus. The same platform also gains a
firmware driver.
- The Samsung Exynos family gains a new Chipid driver exporting using
the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon chips.
- A firmware driver for the NXP i.MX DSP IPC protocol using shared
memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for the S905X3 and A311D
chips
- A rework of the TI Davinci framebuffer driver to allow important
cleanups in the platform code
- A couple of device drivers for removed ARM SoC platforms are
removed. Most of the removals were picked up by other maintainers,
this contains whatever was left"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
bus: uniphier-system-bus: use devm_platform_ioremap_resource()
soc: ti: ti_sci_pm_domains: Add support for exclusive and shared access
dt-bindings: ti_sci_pm_domains: Add support for exclusive and shared access
firmware: ti_sci: Allow for device shared and exclusive requests
bus: imx-weim: remove incorrect __init annotations
fbdev: remove w90x900/nuc900 platform drivers
spi: remove w90x900 driver
net: remove w90p910-ether driver
net: remove ks8695 driver
firmware: turris-mox-rwtm: Add sysfs documentation
firmware: Add Turris Mox rWTM firmware driver
dt-bindings: firmware: Document cznic,turris-mox-rwtm binding
bus: moxtet: fix unsigned comparison to less than zero
bus: moxtet: remove set but not used variable 'dummy'
ARM: scoop: Use the right include
dt-bindings: power: add Amlogic Everything-Else power domains bindings
soc: amlogic: Add support for Everything-Else power domains controller
fbdev: da8xx: use resource management for dma
fbdev: da8xx-fb: drop a redundant if
fbdev: da8xx-fb: use devm_platform_ioremap_resource()
...
The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody is
using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still in
active use and are converted to the ARCH_MULTIPLATFORM build, meaning
that we can compile a kernel that works on these along with most other
ARMv5 platforms. Changes toward that goal are also merged for IOP32x,
but additional work is needed to complete this. Patches for the
remaining ARMv5 platforms have started but need more work and some
testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform
and the move of the TI Davinci platform to a new clocksource driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=u+ew
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Arnd Bergmann:
"The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody
is using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still
in active use and are converted to the ARCH_MULTIPLATFORM build,
meaning that we can compile a kernel that works on these along with
most other ARMv5 platforms. Changes toward that goal are also merged
for IOP32x, but additional work is needed to complete this. Patches
for the remaining ARMv5 platforms have started but need more work and
some testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform and
the move of the TI Davinci platform to a new clocksource driver"
[ The changes had marked INTEL_IOP_ADMA and USB_LPC32XX as being
buildable on other platforms through COMPILE_TEST, but that causes new
warnings that I most definitely do not want to see during the merge
window as that could hide other issues.
So the COMPILE_TEST option got disabled for them again - Linus ]
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: multi_v5_defconfig: make DaVinci part of the ARM v5 multiplatform build
ARM: davinci: support multiplatform build for ARM v5
arm64: exynos: Enable exynos-chipid driver
ARM: OMAP2+: Delete an unnecessary kfree() call in omap_hsmmc_pdata_init()
ARM: OMAP2+: move platform-specific asm-offset.h to arch/arm/mach-omap2
ARM: davinci: dm646x: Fix a typo in the comment
ARM: davinci: dm646x: switch to using the clocksource driver
ARM: davinci: dm644x: switch to using the clocksource driver
ARM: aspeed: Enable SMP boot
ARM: aspeed: Add ASPEED AST2600 architecture
ARM: aspeed: Select timer in each SoC
dt-bindings: arm: cpus: Add ASPEED SMP
ARM: imx: stop adjusting ar8031 phy tx delay
mailmap: map old company name to new one @microchip.com
MAINTAINERS: at91: remove the TC entry
MAINTAINERS: at91: Collect all pinctrl/gpio drivers in same entry
ARM: at91: move platform-specific asm-offset.h to arch/arm/mach-at91
MAINTAINERS: Extend patterns for Samsung SoC, Security Subsystem and clock drivers
ARM: s3c64xx: squash samsung_usb_phy.h into setup-usb-phy.c
ARM: debug-ll: Add support for r7s9210
...
While debugging packet loss towards the CPU, it is useful to be able to
query the CPU port's shared buffer quotas and occupancy.
Since the CPU port has no ingress buffers, all the shared buffers ingress
information will be cleared.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register CPU port with devlink.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Next patch is going to register the CPU port with devlink, but only so
that the CPU port's shared buffer configuration and occupancy could be
queried.
Prevent changing CPU port's shared buffer threshold and binding
configuration.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ena_dev->intr_moder_rx/tx_interval save the intervals received from the
user after dividing them by ena_dev->intr_delay_resolution. Therefore
when intr_delay_resolution changes, the code needs to first mutiply
intr_moder_rx/tx_interval by the previous intr_delay_resolution to get
the value originally given by the user, and only then divide it by the
new intr_delay_resolution.
Current code does not first multiply intr_moder_rx/tx_interval by the old
intr_delay_resolution. This commit fixes it.
Also initialize ena_dev->intr_delay_resolution to be 1.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nonadaptive interrupt moderation intervals are assigned the value set
by the user in ethtool -C divided by ena_dev->intr_delay_resolution.
Therefore when the user tries to get the nonadaptive interrupt moderation
intervals with ethtool -c the code needs to multiply the saved value
by ena_dev->intr_delay_resolution.
The current code erroneously divides instead of multiplying in ethtool -c.
This patch fixes this.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation always updates the interrupt register with
the smoothed_interval of the rx_ring. However this should be
done only in case of adaptive interrupt moderation. If non-adaptive
interrupt moderation is used, the non-adaptive interrupt moderation
interval should be used. This commit fixes that.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove previous implementation of adaptive rx interrupt moderation
from ena_com files.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Deleted unused 4 fields from struct ena_adapter and their only user
ena_restore_ethtool_params().
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Out of the fields {per_napi_bytes, per_napi_packets} in struct ena_ring,
only rx_ring->per_napi_packets are used to determine if napi did work
for dim.
This commit removes all other uses of these fields.
2. Remove ena_ring->moder_tbl_idx, which is not used by dim.
3. Remove all calls to ena_com_destroy_interrupt_moderation(), since all it
did was to destroy the interrupt moderation table, which is removed as
part of removing old interrupt moderation code.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove code duplication in:
ena_com_update_nonadaptive_moderation_interval_tx()
ena_com_update_nonadaptive_moderation_interval_rx()
functions.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver_supported_features to host_host info which is a new API used to
communicate to the device which features are supported by the driver.
Add the interrupt_moderation bit to host_info->driver_supported_features
and enable it to signal the device that this driver supports interrupt
moderation properly.
Reserved bits are for features implemented in the future
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Remove old adaptive interrupt moderation code from set/get_coalesce()
2. Add ena_update_rx_rings_intr_moderation() function for updating
nonadaptive interrupt moderation intervals similarly to
ena_update_tx_rings_intr_moderation().
3. Remove checks of multiple unsupported received interrupt coalescing
parameters. This makes code cleaner and cancels the need to update
it every time a new coalescing parameter is invented.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the dim library for the rx adaptive interrupt moderation implementation
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add intr_moder_rx_interval to struct ena_com_dev and use it as the
location where the interrupt moderation rx interval is saved, instead
of the interrupt moderation table.
This is done as a first step before removing the old interrupt moderation
code.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver becomes the first user of the kernel's `ETHTOOL_PHY_EDPD`
phy-tunable feature.
EDPD is also enabled by default on PHY config_init, but can be disabled via
the phy-tunable control.
When enabling EDPD, it's also a good idea (for the ADIN PHYs) to enable TX
periodic pulses, so that in case the other PHY is also on EDPD mode, there
is no lock-up situation where both sides are waiting for the other to
transmit.
Via the phy-tunable control, TX pulses can be disabled if specifying 0
`tx-interval` via ethtool.
The ADIN PHY supports only fixed 1 second intervals; they cannot be
configured. That is why the acceptable values are 1,
ETHTOOL_PHY_EDPD_DFLT_TX_MSECS and ETHTOOL_PHY_EDPD_NO_TX (which disables
TX pulses).
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When skb_shinfo(skb) is not able to cache extra fragment (that is,
skb_shinfo(skb)->nr_frags >= MAX_SKB_FRAGS), xennet_fill_frags() assumes
the sk_buff_head list is already empty. As a result, cons is increased only
by 1 and returns to error handling path in xennet_poll().
However, if the sk_buff_head list is not empty, queue->rx.rsp_cons may be
set incorrectly. That is, queue->rx.rsp_cons would point to the rx ring
buffer entries whose queue->rx_skbs[i] and queue->grant_rx_ref[i] are
already cleared to NULL. This leads to NULL pointer access in the next
iteration to process rx ring buffer entries.
Below is how xennet_poll() does error handling. All remaining entries in
tmpq are accounted to queue->rx.rsp_cons without assuming how many
outstanding skbs are remained in the list.
985 static int xennet_poll(struct napi_struct *napi, int budget)
... ...
1032 if (unlikely(xennet_set_skb_gso(skb, gso))) {
1033 __skb_queue_head(&tmpq, skb);
1034 queue->rx.rsp_cons += skb_queue_len(&tmpq);
1035 goto err;
1036 }
It is better to always have the error handling in the same way.
Fixes: ad4f15dc2c ("xen/netfront: don't bug in case of too many frags")
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race condition that can occur when calling ena_down().
The ena_clean_tx_irq() - which is a part of the napi handler -
function might wake up the tx queue when the queue is supposed
to be down (during recovery or changing the size of the queues
for example) This causes the ena_start_xmit() function to trigger
and possibly try to access the destroyed queues.
The race is illustrated below:
Flow A: Flow B(napi handler)
ena_down()
netif_carrier_off()
netif_tx_disable()
ena_clean_tx_irq()
netif_tx_wake_queue()
ena_napi_disable_all()
ena_destroy_all_io_queues()
After these flows the tx queue is active and ena_start_xmit() accesses
the destroyed queue which leads to a kernel panic.
fixes: 1738cd3ed3 (net: ena: Add a driver for Amazon Elastic Network Adapters (ENA))
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver periodically generates "trapped" UDP packets that it then
passes on to devlink. Set the offsets to the various protocol layers.
This is a prerequisite to the next patch, where drop monitor is taught
to check that the offset to the MAC header was set.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This qdisc offload is the closest thing to what the SJA1105 supports in
hardware for time-based egress shaping. The switch core really is built
around SAE AS6802/TTEthernet (a TTTech standard) but can be made to
operate similarly to IEEE 802.1Qbv with some constraints:
- The gate control list is a global list for all ports. There are 8
execution threads that iterate through this global list in parallel.
I don't know why 8, there are only 4 front-panel ports.
- Care must be taken by the user to make sure that two execution threads
never get to execute a GCL entry simultaneously. I created a O(n^4)
checker for this hardware limitation, prior to accepting a taprio
offload configuration as valid.
- The spec says that if a GCL entry's interval is shorter than the frame
length, you shouldn't send it (and end up in head-of-line blocking).
Well, this switch does anyway.
- The switch has no concept of ADMIN and OPER configurations. Because
it's so simple, the TAS settings are loaded through the static config
tables interface, so there isn't even place for any discussion about
'graceful switchover between ADMIN and OPER'. You just reset the
switch and upload a new OPER config.
- The switch accepts multiple time sources for the gate events. Right
now I am using the standalone clock source as opposed to PTP. So the
base time parameter doesn't really do much. Support for the PTP clock
source will be added in a future series.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preparation patch for the tc-taprio offload (and potentially
for other future offloads such as tc-mqprio).
Instead of looking directly at skb->priority during xmit, let's get the
netdev queue and the queue-to-traffic-class mapping, and put the
resulting traffic class into the dsa_8021q PCP field. The switch is
configured with a 1-to-1 PCP-to-ingress-queue-to-egress-queue mapping
(see vlan_pmap in sja1105_main.c), so the effect is that we can inject
into a front-panel's egress traffic class through VLAN tagging from
Linux, completely transparently.
Unfortunately the switch doesn't look at the VLAN PCP in the case of
management traffic to/from the CPU (link-local frames at
01-80-C2-xx-xx-xx or 01-1B-19-xx-xx-xx) so we can't alter the
transmission queue of this type of traffic on a frame-by-frame basis. It
is only selected through the "hostprio" setting which ATM is harcoded in
the driver to 7.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support tc-taprio offload, the TTEthernet egress scheduling
core registers must be made visible through the static interface.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new state is required when firmware indicates that the error
recovery process requires polling for firmware state to be completely
down before initiating reset. For example, firmware may take some
time to collect the crash dump before it is down and ready to be
reset.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some error recovery updates to the spec., among other minor changes.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shubhrajyoti Datta