Program the timeout values (in escape clock) for HS TX, LP RX and TA
timeout.
HX TX: Ensure that host does not continuously transmit in the HS
state. If this timer expires, then host will gracefully end its HS
transmission and allow the link to enter into LP state.
LP RX: Monitor the length of LP receptions from Peripheral. If timeout
happens then host will drive the stop state onto all data lanes (only
Data Lane 0 should be receiving anything from the Peripheral). This
effectively takes back ownership of the bus transmit in the HS state.
TA timeout: Timeout valuefor monitoring Bus Turn-Around (BTA) sequence.
BTA sequence should complete within a bounded amount of time, with
peripheral acknowledging BTA by driving the stop state.
v2 by Jani:
- Rebase
- Use intel_dsi_bitrate() and intel_dsi_tlpx_ns(intel_dsi)
- Squash HX TX, LP RX and TA timeout into one patch
- Fix bspec mode set sequence reference
- Add FIXME about two timeouts
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/60e610ccffe5f8c09dee1c65828f28f25227efce.1540900289.git.jani.nikula@intel.com
This patch programs DSI operation mode, pixel format,
BGR info, link calibration etc for the DSI transcoder.
This patch also extract BGR info of the DSI panel from
VBT and save it inside struct intel_dsi which used for
configuring DSI transcoder.
v2: Rebase
v3: Use newly defined bitfields.
v4 by Jani:
- Use intel_dsi_bitrate()
- Make bgr_enabled bool
- Use 0 instead of 0x0
- Replace DRM_ERROR() with MISSING_CASE() on pixel format and video mode
- Use is_vid_mode()
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7de4e39a4b2a18e53a2b9d9cea5b5b4c9d6eeb34.1539613303.git.jani.nikula@intel.com
This patch programs D-PHY timing parameters for the
clock and data lane (in escape clocks) of DSI
controller (DSI port 0 and 1).
These programmed timings would be used by DSI Controller
to calculate link transition latencies of the data and
clock lanes.
v2: Use newly defined bitfields for data and clock lane
v3 by Jani:
- Rebase on dphy abstraction
- Reduce local variables
- Remove unrelated comment changes (Ville)
- Use the same style for range checks as VLV (Ville)
- Assign, don't OR dphy_reg contents
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/70d491e2357f328a63b67ea3c43cb57a1d469c15.1539613303.git.jani.nikula@intel.com
intel_dsi_vbt_init() has grown too unwieldy, and it's about to be
modified due to ICL DSI. Abstract out the VLV specific dphy param
init. No functional changes. Intentionally no stylistic changes during
code movement.
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/96d15760db027a137f298ec330520ef8ec6474b0.1539613303.git.jani.nikula@intel.com
Avoid confusion with the functions to be added for the new ICL or gen 11
DSI implementation by renaming the current DSI functions. While at it,
permutate the words in the function names to make them all start with
"vlv_dsi" or "vlv_dsi_pll" etc.
Reduce the platform abstractions in the PLL file while at it, moving the
checks to vlv_dsi.c instead, where we typically already have the
necessary if ladders.
Leave the static functions as-is for now; they could be renamed later if
needed.
No functional changes.
v2: use "gen7" prefix.
v3: use "vlv" and "bxt" prefixes, reduce the abstractions.
References: https://patchwork.freedesktop.org/series/44823/
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180705132509.12881-2-jani.nikula@intel.com
Move the limit checks near the calculations for each field, and actually
log the values that exceed limits.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180419085940.21505-1-jani.nikula@intel.com
The commit 213e08ad60
("drm/i915/bxt: add bxt dsi gpio element support")
enables GPIO support for Broxton based platforms.
While using that API we might get into troubles in the future, because
we can't rely on label name in the driver since vendor firmware might
provide any GPIO pin there, e.g. "reset", and even mark it in _DSD (in
which case the request will fail).
To avoid inconsistency and potential issues we have two options:
a) generate GPIO ACPI mapping table and supply it via
acpi_dev_add_driver_gpios(), or
b) just pass NULL as connection ID.
The b) approach is much simpler and would work since the driver relies
on GPIO indices only. Moreover, the _CRS fallback mechanism, when
requesting GPIO, has been made stricter, and supplying non-NULL
connection ID when neither _DSD, nor GPIO ACPI mapping is present, is
making request fail.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=101921
Fixes: f10e4bf663 ("gpio: acpi: Even more tighten up ACPI GPIO lookups")
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Tested-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170817105541.63914-1-andriy.shevchenko@linux.intel.com
As per BSPEC, high/low switch count to be programmed in
terms of byteclock using exit_zero_count and prep_count.
For Geminilake exit/prep counts are already calculated
in terms of byteclock. This patch calculates high/low
switch count using counts value in byteclock, old calculation
leads to screen flicker/shift issue while resuming from S3/S4.
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1494336565-19185-1-git-send-email-madhav.chauhan@intel.com
Emphasize that the VBT file is nowadays more about initializing and
running stuff based on the VBT contents, not so much about being a
"panel driver". No functional changes.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/b13cb012a555ff5eb56b5e4bb2b0205c3e025a99.1488810382.git.jani.nikula@intel.com
Madhav Chauhan