This patch detects DSI presence for ICL platform
by reading VBT. DSI detection is done while initializing
DSI using newly added function intel_gen11_dsi_init.
v2 by Jani:
- Preserve old behavour of intel_bios_is_dsi_present()
- s/intel_gen11_dsi_init/icl_dsi_init/g
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2324cdfc8918bda3165354e5e0d15053b1074f14.1540900289.git.jani.nikula@intel.com
In case of Legacy DP connector on TypeC port, the
flex IO DPMLE register is set to number of lanes configured
by the display driver which will be programmed into DDI_BUF_CTL
PORT_WIDTH_SELECTION.
This needs to be programmed before enabling the shared PLLs hence
add a pre_pll_enable hook for ICL and add this programming in that hook.
v2:
* Remove the check for combophy port (Jose)
* Simplify the port reversal check logic (Jose)
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Jose Roberto de Souza <jose.souza@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023191248.26418-2-manasi.d.navare@intel.com
This patch fixes the macros used for defining the DFLEXDPMLE
register bit fields. This accounts for changes in the spec.
Fixes: a2bc69a1a9 ("drm/i915/icl: Add register definition for DFLEXDPMLE")
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jose Roberto de Souza <jose.souza@intel.com>
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023191248.26418-1-manasi.d.navare@intel.com
Otherwise it would be in a inconsistent state as port is disconnected
but with a valid tc type.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181030215750.28213-3-jose.souza@intel.com
Otherwise it would be in a inconsistent state as port is disconnected
but with a valid tc type.
Also setting it to unknown will earlier return
icl_tc_phy_disconnect() for any future calls to
intel_digital_port_connected(), this way we don't need to check if
port is marked as safe everytime.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181030215750.28213-2-jose.souza@intel.com
Besides of give the expected output of i915_display_info it will also
avoid some aux ch transactions that would timeout by obvious reasons.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181030215750.28213-1-jose.souza@intel.com
Let's not leak obj->framebuffer_references when we decide that
the framebuffer domensions are not suitable for NV12.
Cc: stable@vger.kernel.org
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Vidya Srinivas <vidya.srinivas@intel.com>
Fixes: e44134f267 ("drm/i915: Add NV12 support to intel_framebuffer_init")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029140031.11765-1-ville.syrjala@linux.intel.com
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Use intel_panel_actually_set_backlight() instead of a direct
call to pwm_config() in pwm_disable_backlight().
The main benefit is consistent debug logging when we turn off the
backlight. Currently we see nothing in dmesg which made me wonder
whether the backlight was even getting turned off properly.
The second benefit is consistency; This is what we do for all
the other backlight implementations.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181024155208.18987-1-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jani Nikula <jani.nikula@intel.com>
DP 1.4 spec defines DP secondary data packet for DSC
picture parameter set. This patch defines its payload size
according to the DP 1.4 specification.
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org> (For merging through
drm-intel)
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-7-manasi.d.navare@intel.com
When DSC is supported we need to validate the modes based on the
maximum supported compressed BPP and maximum supported slice count.
This allows us to allow the modes with pixel clock greater than the
available link BW as long as it meets the compressed BPP
and slice count requirements.
v3:
* Use the macro for dsc sink support (Jani N)
v2:
* Properly comment why we are right shifting the bpp value (Anusha)
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-6-manasi.d.navare@intel.com
This patch adds helpers for calculating the maximum compressed BPP
supported with small joiner.
This also adds a helper for calculating the slice count in case
of small joiner.
These are inside intel_dp since they take into account hardware
limitations.
v6:
* Take mode_clock and mode_hdisplay as input arguments
so that this can be called in intel_dp_mode_valid (Manasi)
v5:
* Get the max slice width from DPCD
* Check against Min_Slice_width of 2560 (Anusha)
v4:
* #defines for PPR in slice count helper (Gaurav)
v3:
* Simply logic for bpp (DK)
* Limit the valid slice count by max supported by Sink (Manasi)
v2:
* Change the small joiner RAM buffer constant as bspec changed (Manasi)
* rename it as SMALL_JOINER since we are not enabling
big joiner yet (Anusha)
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-5-manasi.d.navare@intel.com
This patch adds inline functions and helpers for obtaining
DP sink's supported DSC parameters like DSC sink support,
eDP compressed BPP supported, maximum slice count supported
by the sink devices, DSC line buffer bit depth supported on DP sink,
DSC sink maximum color depth by parsing corresponding DPCD registers.
v4:
* Add helper to give line buf bit depth (Manasi)
* Correct the bit masking in color depth helper (manasi)
v3:
* Use SLICE_CAP_2 for DP (Anusha)
v2:
* Add DSC sink support macro (Jani N)
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org> (For merging through
drm-intel)
Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-4-manasi.d.navare@intel.com
DSC is supported on eDP starting GEN 10 display (on GLK) and on DP starting
GEN 11.
This patch implements the discovery phase of DSC. On hotplug,
source reads the DSC DPCD register set (0x00060 - 0x0006F) to
read the decompression capabilities of the sink device.
This entire block of registers is cached in intel_dp so that
capability information can be used during DSC configuration
phase during compute_config phase of the modeset.
For eDP, this caching happens during the eDP initialization.
This caching is done only for eDP and DP rev >= 1.4
v5:
* Fix the block comment (Gaurav)
* Fix the commit message DSC DPCD addresses (Gaurav)
* Use DRM_ERROR for dpcd_read fail (Gaurav,Anusha)
v4:
* Cache these only for Gen >= 11
v3:
* Remove the dsc_sink_support field in intel_dp (Jani N)
v2:
* Clear the cached registers on hotplug always (Jani N)
* Combine the eDP and DP caching in same function (Jani N)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-3-manasi.d.navare@intel.com
This patch defines the DP DSC receiver capability size that gives
total number of DP DSC DPCD registers.
This also adds a missing #defines for DP DSC support missed in the
commit id (ab6a46ea68 "Add DPCD definitions for DP 1.4 DSC feature")
v3:
* MIN_SLICE_WIDTH = 2560 (Anusha)
* Define DP_DSC_SLICE_WIDTH_MULTIPLIER = 320
v2:
* Add SHIFT define and DECOMPRESSION_EN define missed in prev patch
Cc: dri-devel@lists.freedesktop.org
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Acked-by: Sean Paul <seanpaul@chromium.org> (For merging through
drm-intel)
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-2-manasi.d.navare@intel.com
Add the newly added slice_row_per_frame parameter
in the Picture Parameter Set registers.
This defines the number of vertically stacked slices
in a frame.
Credits to Manasi for noticing bSpec change.
Suggested-by: Manasi Navare <manasi.d.navare@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-1-manasi.d.navare@intel.com
Program the timeout values (in escape clock) for HS TX, LP RX and TA
timeout.
HX TX: Ensure that host does not continuously transmit in the HS
state. If this timer expires, then host will gracefully end its HS
transmission and allow the link to enter into LP state.
LP RX: Monitor the length of LP receptions from Peripheral. If timeout
happens then host will drive the stop state onto all data lanes (only
Data Lane 0 should be receiving anything from the Peripheral). This
effectively takes back ownership of the bus transmit in the HS state.
TA timeout: Timeout valuefor monitoring Bus Turn-Around (BTA) sequence.
BTA sequence should complete within a bounded amount of time, with
peripheral acknowledging BTA by driving the stop state.
v2 by Jani:
- Rebase
- Use intel_dsi_bitrate() and intel_dsi_tlpx_ns(intel_dsi)
- Squash HX TX, LP RX and TA timeout into one patch
- Fix bspec mode set sequence reference
- Add FIXME about two timeouts
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/60e610ccffe5f8c09dee1c65828f28f25227efce.1540900289.git.jani.nikula@intel.com
This patch sends command and executes display off,
assert reset, power off VBT seqeuences to power
down DSI panel. Patch also adds high level function
to wrap all the panel sepcific programming during
DSI disabling.
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/efdafbf6b4d31123738b87b2d8264a9b5553eb32.1540900289.git.jani.nikula@intel.com
Driver needs payload/header credits for sending any command
and data over DSI link. These credits are released once command
or data sent to link. This patch adds functions to wait for releasing
of payload and header credits.
As per BSPEC, driver needs to ensure that all of commands/data
has been dispatched to panel before the transcoder is enabled.
This patch implement those steps i.e. sending NOP DCS command,
wait for header/payload credit to be released etc.
v2 by Jani:
- squash the credit wait helpers patch with the first user
- pass dev_priv to the credit wait helpers
- bikeshed credit helper names
- wait for *at least* the current maximum number of credits
- indentation fix
- add helpers for credits available
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/84bc509beabf2a2d1324a9f2a67ab4ebe05b10a6.1540900289.git.jani.nikula@intel.com
Commit b24413180f ("License cleanup: add SPDX GPL-2.0 license
identifier to files with no license") added "SPDX-License-Identifier:
GPL-2.0" to files which previously had no license, change this to MIT
for intel_ringbuffer.h matching the license text of intel_ringbuffer.c.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031005331.20775-1-jsg@jsg.id.au
When using softpin it's not enough to just pad the vma size, we also
need to ensure the vma offset is at the start of the pt boundary, if we
plan to utilize 64K pages. Therefore to improve test coverage we should
use both aligned and unaligned gtt offsets in igt_write_huge.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029203734.21936-1-matthew.auld@intel.com
This reverts commit c9e666880d.
Checked GVT codes that guest PPGTT PTE flag bits are propagated
to shadow PTE. Read/write bit is not changed. Further tested by
i915 self-test case "igt_ctx_readonly". No error or GPU hang was
detected. So enable read-only support under GVT.
Signed-off-by: Hang Yuan <hang.yuan@linux.intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1540883281-11359-1-git-send-email-hang.yuan@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
ICL supports DC5, DC6, and DC9. Enable DC9 during screen-off, and enable
DC5/6 when appropriate.
v2: (James Ausmus)
- Also handle ICL as GEN9_LP in i915_drm_suspend_late and
i915_drm_suspend_early
- Add DC9 to gen9_dc_mask for ICL
- Re-order GEN checks for newest platform first
- Use INTEL_GEN instead of INTEL_INFO->gen
- Use INTEL_GEN >= 11 instead of IS_ICELAKE
- Consolidate GEN checks
v3: (James Ausmus)
- Also allow DC6 for ICL (Imre, Art)
- Simplify !(GEN >= 11) to GEN < 11 (Imre)
v4: (James Ausmus)
- Don't call intel_power_sequencer_reset after DC9 for Gen11+, as the
PPS regs are Always On
- Rebase against upstream changes
v5: (Anusha Srivatsa)
- rebased against the latest upstream changes.
v6: (Anusha Srivatsa)
- rebased.Use INTEL_GEN consistently.
- Simplify the code (Rodrigo)
v7: rebased. Change order according to platforms(Jyoti)
v8: rebased. Change the check from platform specific to
HAS_PCH_SPLIT(). Add comment in code to be more clear.(Rodrigo)
Cc: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Tested-by: Jyoti Yadav <jyoti.r.yadav@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029221410.4423-1-anusha.srivatsa@intel.com
If we reduce the suspend function for intel_opregion to do the minimum
required, the resume function can also do the simple task of notifier
the ACPI bios that we are back. This avoid some nasty restrictions on
the likes of register_acpi_notifier() that are not allowed during the
early phase of resume.
v2: Keep the order of acpi notify vs turning off ardy/drdy the same.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181030110554.4111-1-chris@chris-wilson.co.uk
If we can prevent stray writes from landing in the scratch page, we can
reuse the same page and same scratch PT for all contexts without fear of
information leaks and side-channels.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029182721.29568-2-chris@chris-wilson.co.uk
Record the scratch PTE encoding upon creation rather than recomputing
the bits everytime. This is important for the next patch where we forgo
having a valid scratch page with which we may compute the bits and so
require keeping the PTE value instead.
v2: Fix up scrub_64K to use scratch_pte as well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029182721.29568-1-chris@chris-wilson.co.uk
intel_fb_pitch_limit() has the parameters pixel_format and fb_modifier
switched in their positions. The parameters are however used correctly,
but change the order for consistency.
Also use kernel data types for both parameters.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026195342.16828-1-dhinakaran.pandiyan@intel.com
The PLANE_AUX_OFFSET mmio does not exist on ICL, do not program it. We'll
still calculate the aux offset as it is required for adjusing x-y offsets.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026193805.11077-2-dhinakaran.pandiyan@intel.com
A framebuffer can comprise surfaces with distinct tiling formats,
making checks against modifier alone insufficient. Make use of a
function to identify a linear surface based on both modifier and color
plane.
v2: Typo fix
v3: remove 'inline' from function definition (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026193805.11077-1-dhinakaran.pandiyan@intel.com
The specially case for SKL for not controlled sagv
is already taken care inside intel_enable_sagv, so there's
no need to duplicate the check here.
v2: Go one step further and remove skl special case. (Jani)
v3: Separate runtime status handle from has_sagv flag.
v4: Go back and accept simple Jani proposed solution.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026200317.21726-1-rodrigo.vivi@intel.com
The vm of two contexts are supposed to be independent, such that a stray
write by one cannot be detected by another. Normally the GTT is filled
explicitly by userspace, but the space in between objects is filled with
a scratch page -- and that scratch page should not be able to form an
inter-context backchannel.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029172925.10159-1-chris@chris-wilson.co.uk
While checking the opportunity to add a display_gen
check to allow glk and cnl to be on same bucket I noticed
these FIXME cases here.
So I got the confirmation from HW architect that we actually
never needed this workaround.
"GLK supports 2 pixel per clock, so pixel clock can be up to 2 * cdclk."
So, this reverts commit 97f55ca5b6 ("drm/i915/glk: limit pixel
clock to 99% of cdclk workaround")
Fixes: 97f55ca5b6 ("drm/i915/glk: limit pixel clock to 99% of cdclk workaround")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026005636.22274-1-rodrigo.vivi@intel.com
commit ac657f6461 ("drm/i915: Introduce IS_GEN macro") introduced
GEN_FOREVER that was never used.
My first attempt was to rename it to FOREVER since GEN is
already part of the macro. Then I used coccinelle to change all
-INTEL_GEN(e1) >= e2
+INTEL_GEN_RANGE(e1, e2, FOREVER)
-INTEL_GEN(e1) <= e2
+INTEL_GEN_RANGE(e1, 0, e2)
and I liked it.
However I didn't like very much the remaining
INTEL_GEN(dev_priv) < n
and:
INTEL_GEN(e1) < n
INTEL_GEN_RANGE(e1, 0, n - 1)
didn't make much sense either.
So INTEL_GEN use for > or < seems a better unified way for unlimited
bounds. So, no reason to keep GEN_FOREVER here.
Let's kill before someone start using it.
v2: Remove remaining GEN_FOREVER forgotten in a comment. (Daniel)
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026195143.20353-2-rodrigo.vivi@intel.com
Madhav Chauhan