As spotted by Dan Carpenter <dan.carpenter@oracle.com> (thanks!), we have
improperly used an unsigned variable in a calculation that may result in a
negative number. This may cause an unintended underflow if the interface
frequency of the tuner is > approx. 40MHz.
This patch should resolve the issue, following an approach similar to what is
used in af9013.c.
[crope@iki.fi: add Reported-by]
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to udev-182, the firmware load was changed to be async, as
otherwise udev would give up of loading a firmware.
Add an option to return to the previous behaviour, async firmware
loads cause failures with the tda18271 driver.
Antti tested it with the following hardware:
Hauppauge WinTV HVR 930C
MaxMedia UB425-TC
PCTV QuatroStick nano (520e)
Tested-by: Antti Palosaari <crope@iki.fi>
Cc: stable@kernel.org # for Kernel 3.6 - please note that driver location has changed
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is fallback condition as GPIOLIB seems to be disabled by default.
Better solution is needed, maybe GPIOLIB could be enabled by default?
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
tda1004x doesn't allow firmware loads while it is busy with something
else. Avoid it to happen by locking the I2C bus during firmware transfer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is initial support for the Asus MyCinema U3100Mini Plus. The driver
in its current form gets detected and loads properly.
Scanning using dvbscan works without problems, Locking onto a channel
using tzap also works fine. Only playback using tzap -r + mplayer was
tested and was fully functional.
It uses the af9035 USB Bridge chip, with an af9033 demodulator. The tuner
used is the FCI FC2580.
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently there is LNA behind cxd2820r demodulator GPIO. Use
Kernel GPIO interface to access those GPIOs.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This optimizes few hundred bytes from data to text segment.
Also remove one unused function that was commented out already.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use .get_if_frequency() as all used tuner drivers
(mt2060/qt1010/mxl5005s) supports it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is first step closer to support multiple tuners.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Used IF frequency is one of the most important parameter to know.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is done as a minimal printk updating patch to ensure correctness. Yes
it should all one day use dev_foo(), but that's one for the maintainers.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=32932
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implementation taken from rtl2830.
Cc: Thomas Mair <thomas.mair86@googlemail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Am 14.08.2012 14:05, schrieb Manu Abraham:
>> My other device, a STB0899, always reports the set frequency. So it seems
>> driver dependent whether it reports the actually locked frequency found by
>> the zig-zag-algorithm or just the set frequency to tune to.
>
> The STV0299 blindly sets the value based on a software zigzag (due to simpler
> hardware), but this might not be accurate enough. On the other hand, the
> STB0899 internally does zig-zag in hardware for DVB-S2, and partly in
> software for DVB-S.
>
> In any event, the get_frontend callback should return the value that is read
> from the demodulator registers, rather than the cached original value that
> which was requested to be tuned.
>
> The stb0899 returns only the cached value IIRC. Maybe I will fix this soon,
> or maybe you can send a patch.
This is what I get after the patch:
Sat. Pol. Band Freq (MHz) Set Freq (MHz) Get Delta (MHz)
S19,2E H L 10744 10748,474 4,474
S19,2E H L 10773 10777,944 4,944
S19,2E H L 10832 10836,953 4,953
S19,2E H L 10861 10868,774 7,774
...
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let the dvb-frontend return -ENOTTY for those unimplemented IOCTLs.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of having 3 options to allow customizing the media
sub-drivers (tuners, I2C drivers, frontends), merge all of
them into just one.
That simplifies the life for users, as they can just keep
this untouched.
Life for developers is also simpler, as there's now just
one Kconfig item to remember, for the ancillary sub-drivers
providing supports for chips that could change from one
board design to another.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On a few places, := were using instead of +=, causing drivers to
not compile.
While here, standardize the usage of += on all cases where multiple
lines are needed, and for obj-y/obj-m targets, and := when just one
line is needed, on <module>-obj rules.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Identified-by: Antti Polosaari <crope@iki.fi>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This code looks suspicious, but it turns out that "nv" is an array of u8
so sizeof() is the same as ARRAY_SIZE(). Using ARRAY_SIZE() is more
readable though.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the tuners one level up, as the "common" directory will be used
by drivers that are shared between more than one driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Raise the DVB frontends one level up, as the intention is to remove
the drivers/media/dvb directory.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>